F.3 Test Tolerance and Derivation of Test Requirements (informative)
38.521-23GPPNRPart 2: Range 2 StandaloneRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification
TBD
F.3.1 Measurement of test environments
TBD
F.3.2 Measurement of transmitter
Editor’s note: This clause is incomplete. The following aspects are either missing or not yet determined:
- Influence of noise is subtracted from MTSU before calculating the TT for lower limit Tx test cases.
Table F.3.2-1: Derivation of Test Requirements (Transmitter tests)
|
Sub clause |
Test Tolerance (TT) |
Formula for test requirement |
|||
|
6.2.1.1 UE maximum output power (EIRP) |
PC3 Minimum peak EIRP IFF (Max Device size ≤ 30 cm) 2.87 dB (FR2a, NTC) 2.87 dB (FR2b, NTC) 3.04 dB (FR2a, ETC) 3.04 dB (FR2b, ETC) PC1 Minimum peak EIRP IFF (Max Device size ≤ 30 cm) [3.12] dB (FR2a, NTC) TBD dB (FR2b, NTC) TBD dB (FR2a, ETC) TBD dB (FR2b, ETC) Max EIRP 0 dB |
PC3 Minimum peak EIRP TT = 0.60 x (MTSUIFF – 0.1) (FR2a) TT = 0.60 x (MTSUIFF – 0.3) (FR2b) PC1 Minimum peak EIRP TT = 0.60 x (MTSUIFF – [0.13]) (FR2a) TT = TBD (FR2b) |
|||
|
6.2.1.1 UE maximum output power (TRP) |
PC3 Max TRP IFF (Max Device size ≤ 30 cm) 2.65 dB (FR2a, NTC) 2.77 dB (FR2b, NTC) 2.82 dB (FR2a, ETC) 2.94 dB (FR2b, ETC) PC1 Max TRP IFF (Max Device size ≤ 30 cm) [2.78] dB (FR2a, NTC) TBD dB (FR2b, NTC) TBD dB (FR2a, ETC) TBD dB (FR2b, ETC) |
Max TRP TT = 0.60 x MTSUIFF |
|||
|
6.2.1.1_1 UE maximum output power – EIRP (Rel-16 and forward) |
Same as 6.2.1.1 |
||||
|
6.2.1.2 UE maximum output power (Spherical coverage) |
PC1 TBD PC2 TBD PC3 IFF (Max Device size ≤ 30 cm) 2.58 dB (FR2a) 2.58 dB (FR2b) PC4 TBD |
PC3 TT = 0.60 x (MTSUIFF – 0.3) (FR2a) TT = 0.60 x (MTSUIFF – 0.9) (FR2b) PC1 TBD |
|||
|
6.2.1.2_1 UE maximum output power – Spherical coverage (Rel16 and forward) |
Same as 6.2.1.2 |
||||
|
6.2.2 UE maximum output power reduction |
PC3 Minimum peak EIRP IFF (Max Device size ≤ 30 cm) 3.11 dB (FR2a, NTC) 3.11 dB (FR2b, NTC) 3.30 dB (FR2a, ETC) 3.30 dB (FR2b, ETC) |
Minimum peak EIRP TT = 0.65 x (MTSUIFF – 0.13) (FR2a) TT = 0.65 x (MTSUIFF – 0.31) (FR2b) |
|||
|
6.2.2_1 UE maximum output power reduction enhancements |
Same as 6.2.2 |
||||
|
6.2.3 UE maximum output power with additional requirements |
Same as 6.2.2 |
||||
|
6.2.4 Configured transmitted power |
TBD |
||||
|
6.2.4_1 Configured transmitted power with Power Boost |
Same as 6.2.1.1 |
||||
|
6.2A.1.1.1 UE maximum output power – EIRP and TRP for CA (2UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.2.1 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous TBD |
||||
|
6.2A.1.1.2 UE maximum output power – EIRP and TRP for CA (3UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.2.1 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous TBD |
||||
|
6.2A.1.1.3 UE maximum output power – EIRP and TRP for CA (4UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.2.1 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous TBD |
||||
|
6.2A.1.1.4 UE maximum output power – EIRP and TRP for CA (5UL CA) |
Intra-band contiguous CA, Intra-band non-contiguous CA TBD |
||||
|
6.2A.1.1.5 UE maximum output power – EIRP and TRP for CA (6UL CA) |
Intra-band contiguous CA, Intra-band non-contiguous CA TBD |
||||
|
6.2A.1.1.6 UE maximum output power – EIRP and TRP for CA (7UL CA) |
Intra-band contiguous CA, Intra-band non-contiguous CA TBD |
||||
|
6.2A.1.1.7 UE maximum output power – EIRP and TRP for CA (8UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.2A.1.2.1 Spherical coverage for CA (2UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.2.1.2 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.2A.1.2.2 Spherical coverage for CA (3UL CA) |
Maximum aggregated BW ≤ 400MHz Same as 6.2.1.2 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.2A.1.2.3 Spherical coverage for CA (4UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.2.1.2 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.2A.1.2.4 Spherical coverage for CA (5UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.2A.1.2.5 Spherical coverage for CA (6UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.2A.1.2.6 Spherical coverage for CA (7UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.2A.1.2.7 Spherical coverage for CA (8UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.2A.2.1 UE maximum output power reduction for CA (2UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.2.2 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.2A.2.2 UE maximum output power reduction for CA (3UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.2.2 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.2A.2.3 UE maximum output power reduction for CA (4UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.2.2 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.2A.2.4 UE maximum output power reduction for CA (5UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.2A.2.5 UE maximum output power reduction for CA (6UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.2A.2.6 UE maximum output power reduction for CA (7UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.2A.2.7 UE maximum output power reduction for CA (8UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.2D.2 UE maximum output power reduction for UL MIMO |
Same as 6.2.2 |
||||
|
6.2D.3 UE maximum output power with additional requirements for UL MIMO |
Same as 6.2.3 |
||||
|
6.3.1 Minimum output power |
PC3 Minimum EIRP IFF (Max Device size ≤ 30 cm) NTC 4.21 dB (FR2a 50 MHz) 2.52 dB (FR2a 100 MHz) 0.66 dB (FR2a 200 MHz) 0 dB (FR2a 400 MHz) 1.17 dB (FR2b 50 MHz) 0 dB (FR2b 100 MHz) 0 dB (FR2b 200 MHz) 0 dB (FR2b 400 MHz) ETC 4.37 dB (FR2a 50 MHz) 2.68 dB (FR2a 100 MHz) 0.82 dB (FR2a 200 MHz) 0 dB (FR2a 400 MHz) 1.33 dB (FR2b 50 MHz) 0 dB (FR2b 100 MHz) 0 dB (FR2b 200 MHz) 0 dB (FR2b 400 MHz) |
Minimum EIRP TT = max(R, ΔSNRmr + 0.65 x (MTSUIFF – 1.0)) -R R: Relaxation needed to limit influence of TE noise to 1 dB (specified in clause 6.3.1.5) ΔSNRmr: Systematic offset due to noise when measuring at minimum requirement level (-13 dBm) FR2a 50 MHz: ΔSNRmr = 0.86 dB FR2a 100 MHz: ΔSNRmr = 1.57 dB FR2a 200 MHz: ΔSNRmr = 2.71 dB FR2a 400 MHz: ΔSNRmr = 4.35 dB FR2b 50 MHz: ΔSNRmr = 2.32 dB FR2b 100 MHz: ΔSNRmr = 3.82 dB FR2b 200 MHz: ΔSNRmr = 5.82 dB FR2b 400 MHz: ΔSNRmr = 8.21 dB |
|||
|
6.3.2 Transmit OFF power |
0 dB |
||||
|
6.3.3.2 General ON/OFF time mask |
PC3: ON Power Same as 6.2.1.1 (EIRP) OFF Power 0 dB |
ON Power: Same as 6.2.1.1 (EIRP) OFF Power: Same as 6.3.1 |
|||
|
6.3.3.4 PRACH time mask |
PC3: OFF Power Max Device size ≤ 30cm 0 dB ON Power Max Device size ≤ 30cm TBD (FR2a) TBD (FR2b)TBD |
ON Power TBD |
|||
|
6.3.4.2 Absolute power tolerance |
PC3 Max Device size ≤ 30 cm ±8.05 dB (FR2a & FR2b, NTC testing) ±8.42 dB (FR2a & FR2b, ETC testing) |
TT = MTSU |
|||
|
6.3.4.3 Relative power tolerance |
PC3 IFF (Max Device size ≤ 30 cm) [0.46 dB] (FR2a) [0.46 dB] (FR2b) |
PC3 TT = 0.65 x (MTSUIFF – 1.0) (FR2a) TT = 0.65 x (MTSUIFF – 1.0) (FR2b) (assuming a power step ΔP = 1 dB) |
|||
|
6.3.4.4 Aggregate power tolerance |
PC3 IFF (Max Device size ≤ 30 cm) 0.26 dB (FR2a) 0.26 dB (FR2b) |
PC3 TT = 0.65 x (MTSUIFF – 1.0) (FR2a) TT = 0.65 x (MTSUIFF – 1.0) (FR2b) (assuming a power step ΔP = 1 dB) |
|||
|
6.3A.1.1 Minimum output power for CA (2UL CA) |
For UL CA aggregated BW ≤ 800 MHz: Same as 6.3.1 For UL CA aggregated BW > 800 MHz: TBD |
||||
|
6.3A.1.2 Minimum output power for CA (3UL CA) |
For UL CA aggregated BW ≤ 800 MHz: Same as 6.3.1 For UL CA aggregated BW > 800 MHz: TBD |
||||
|
6.3A.1.3 Minimum output power for CA (4UL CA) |
For UL CA aggregated BW ≤ 800 MHz: Same as 6.3.1 For UL CA aggregated BW > 800 MHz: TBD |
||||
|
6.3A.1.4 Minimum output power for CA (5UL CA) |
For UL CA aggregated BW ≤ 800 MHz: Same as 6.3.1 For UL CA aggregated BW > 800 MHz: TBD |
||||
|
6.3A.1.5 Minimum output power for CA (6UL CA) |
For UL CA aggregated BW ≤ 800 MHz: Same as 6.3.1 For UL CA aggregated BW > 800 MHz: TBD |
||||
|
6.3A.1.6 Minimum output power for CA (7UL CA) |
For UL CA aggregated BW ≤ 800 MHz: Same as 6.3.1 For UL CA aggregated BW > 800 MHz: TBD |
||||
|
6.3A.1.7 Minimum output power for CA (8UL CA) |
For UL CA aggregated BW ≤ 800 MHz: Same as 6.3.1 For UL CA aggregated BW > 800 MHz: TBD |
||||
|
6.3A.3.1.1 General ON/OFF time mask for CA (2UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.3.3 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.3A.3.1.2 General ON/OFF time mask for CA (3UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.3.3 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.3A.3.1.3 General ON/OFF time mask for CA (4UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.3.3 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.3A.3.1.4 General ON/OFF time mask for CA (5UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.3A.3.1.5 General ON/OFF time mask for CA (6UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.3A.3.1.6 General ON/OFF time mask for CA (7UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.3A.3.1.7 General ON/OFF time mask for CA (8UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.3D.3.1 General ON/OFF time mask for UL MIMO |
PC3: OFF Power Max Device size ≤ 30cm 0 dB ON Power Max Device size ≤ 30cm TBD (FR2a) TBD (FR2b) |
ON Power TBD |
|||
|
6.3D.3.4 SRS time mask for UL MIMO |
PC3: OFF Power Max Device size ≤ 30cm 0 dB ON Power Max Device size ≤ 30cm TBD (FR2a) TBD (FR2b) |
ON Power TBD |
|||
|
6.3A.4.2.1 Absolute power tolerance for CA (2UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.3.4.2 for each CC. Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.3A.4.2.2 Absolute power tolerance for CA (3UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.3.4.2 for each CC. Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.3A.4.2.3 Absolute power tolerance for CA (4UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.3.4.2 for each CC. Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.3A.4.2.4 Absolute power tolerance for CA (5UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.3.4.2 for each CC. Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.3A.4.2.5 Absolute power tolerance for CA (6UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.3.4.2 for each CC. Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.3A.4.2.6 Absolute power tolerance for CA (7UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.3.4.2 for each CC. Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.3A.4.2.7 Absolute power tolerance for CA (8UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.3.4.2 for each CC. Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.3A.4.3.1 Relative power tolerance for CA (2UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz TBD Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.3A.4.3.2 Relative power tolerance for CA (3UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz TBD Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.3A.4.3.3 Relative power tolerance for CA (4UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz TBD Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.3A.4.3.4 Relative power tolerance for CA (5UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.3A.4.3.5 Relative power tolerance for CA (6UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.3A.4.3.6 Relative power tolerance for CA (7UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.3A.4.3.7 Relative power tolerance for CA (8UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.3A.4.4.1 Aggregate power tolerance for CA (2UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.3.4.4 for each CC. Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.3A.4.4.2 Aggregate power tolerance for CA (3UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.3.4.4 for each CC. Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.3A.4.4.3 Aggregate power tolerance for CA (4UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.3.4.4 for each CC. Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.3A.4.4.4 Aggregate power tolerance for CA (5UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.3A.4.4.5 Aggregate power tolerance for CA (6UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.3A.4.4.6 Aggregate power tolerance for CA (7UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.3A.4.4.7 Aggregate power tolerance for CA (8UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.4.1 Frequency error |
0.005 ppm (NTC & ETC testing) |
TT = 0.5 x MTSU |
|||
|
6.4.2.1 Error vector magnitude |
PUSCH, PC3, FR2a: As defined in Table 6.4.2.1.5-2. PUSCH, PC3, FR2b: As defined in Table 6.4.2.1.5-3. |
Minimum requirement + TT EVM_meas_Increase = sqrt(Minimum requirement^2 + MTSU^2) – Minimum requirement; it is the increase of measured EVM due to test equipment uncertainty. EVM_meas_Increase_Relative = EVM_meas_Increase / Minimum requirement [%] If (EVM_meas_Increase_Relative < 7.5%) TT = 0% Else if (7.5% ≤ EVM_meas_Increase_Relative ≤ 50%) TT = EVM_meas_Increase Else Skip the test as not testable. |
|||
|
6.4.2.2 Carrier leakage |
IFF (Max Device size ≤ 30 cm) FR2a: ±3.54 dB (BW ≤ 400MHz) FR2b: ±3.62 dB (BW ≤ 400MHz) |
TT = 0.65 x MTSUIFF |
|||
|
6.4.2.3 In-band emissions |
TBD |
||||
|
6.4.2.4 EVM equalizer spectrum flatness |
TBD |
||||
|
6.4.2.5 EVM equalizer spectrum flatness for BPSK modulation |
TBD |
||||
|
6.4A.1.1 Frequency error for CA (2UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.4.1 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.4A.1.2 Frequency error for CA (3UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.4.1 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.4A.1.3 Frequency error for CA (4UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.4.1 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.4A.1.4 Frequency error for CA (5UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.4A.1.5 Frequency error for CA (6UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.4A.1.6 Frequency error for CA (7UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.4A.1.7 Frequency error for CA (8UL CA) |
Intra-band contiguous CA TBD |
||||
|
6.4A.2.1.1 Error Vector magnitude for CA (2UL CA) |
TBD |
||||
|
6.4A.2.1.2 Error Vector magnitude for CA (3UL CA) |
TBD |
||||
|
6.4A.2.1.3 Error Vector magnitude for CA (4UL CA) |
TBD |
||||
|
6.4A.2.1.4 Error Vector magnitude for CA (5UL CA) |
TBD |
||||
|
6.4A.2.1.5 Error Vector magnitude for CA (6UL CA) |
TBD |
||||
|
6.4A.2.1.6 Error Vector magnitude for CA (7UL CA) |
TBD |
||||
|
6.4A.2.1.7 Error Vector magnitude for CA (8UL CA) |
TBD |
||||
|
6.4A.2.2.1 Carrier leakage for CA (2UL CA) |
TBD |
||||
|
6.4A.2.2.2 Carrier leakage for CA (3UL CA) |
TBD |
||||
|
6.4A.2.2.3 Carrier leakage for CA (4UL CA) |
TBD |
||||
|
6.4A.2.2.4 Carrier leakage for CA (5UL CA) |
TBD |
||||
|
6.4A.2.2.5 Carrier leakage for CA (6UL CA) |
TBD |
||||
|
6.4A.2.2.6 Carrier leakage for CA (7UL CA) |
TBD |
||||
|
6.4A.2.2.7 Carrier leakage for CA (8UL CA) |
TBD |
||||
|
6.4A.2.3.1 In-band emissions for CA (2UL CA) |
TBD |
||||
|
6.4A.2.3.2 In-band emissions for CA (3UL CA) |
TBD |
||||
|
6.4A.2.3.3 In-band emissions for CA (4UL CA) |
TBD |
||||
|
6.4A.2.3.4 In-band emissions for CA (5UL CA) |
TBD |
||||
|
6.4A.2.3.5 In-band emissions for CA (6UL CA) |
TBD |
||||
|
6.4A.2.3.6 In-band emissions for CA (7UL CA) |
TBD |
||||
|
6.4A.2.3.7 In-band emissions for CA (8UL CA) |
TBD |
||||
|
6.5.1 Occupied bandwidth |
0 kHz |
Minimum requirement + TT |
|||
|
6.5.2.1 Spectrum Emission Mask |
IFF (Max Device size ≤ 30 cm) 3.21 dB (FR2a) 3.46 dB (FR2b) |
TT = 0.65 x MTSUIFF |
|||
|
6.5.2.3 Adjacent Channel Leakage Ratio |
Absolute requirement 0 dB Relative requirement IFF (Max Device size ≤ 30 cm) FR2a: ±4.66 dB (BW ≤ 50MHz) ±4.96 dB (50MHz < BW ≤ 100MHz) ±4.96 dB (100MHz < BW ≤ 200MHz) ±4.96 dB (200MHz < BW ≤ 400MHz) FR2b: ±4.96 dB (BW ≤ 50MHz) ±4.96 dB (50MHz < BW ≤ 100MHz) ±4.96 dB (100MHz < BW ≤ 200MHz) ±4.96 dB (200MHz < BW ≤ 400MHz) |
TT = max(R, ΔSNRmr+0.65 x (MTSUIFF-1.0)) -R + TT due to metric change TT due to metric change : 1.0 dB R: Relaxation needed to limit influence of TE noise to 1 dB (specified in clause 6.5.2.3.5) ΔSNRmr: Systematic offset due to noise when measuring ACP at minimum requirement level |
|||
|
6.5.3.1 Transmitter Spurious emissions |
0 dB |
Minimum requirement + TT |
|||
|
6.5.3.2 Spurious emission band UE co-existence |
0 dB |
Minimum requirement + TT |
|||
|
6.5.3.3 Additional spurious emission |
0 dB |
Minimum requirement + TT |
|||
|
6.5A.1.1 Occupied bandwidth for CA (2UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.5.1 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.5A.1.2 Occupied bandwidth for CA (3UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.5.1 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.5A.1.3 Occupied bandwidth for CA (4UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.5.1 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.5A.1.4 Occupied bandwidth for CA (5UL CA) |
TBD |
||||
|
6.5A.1.5 Occupied bandwidth for CA (6UL CA) |
TBD |
||||
|
6.5A.1.6 Occupied bandwidth for CA (7UL CA) |
TBD |
||||
|
6.5A.1.7 Occupied bandwidth for CA (8UL CA) |
TBD |
||||
|
6.5A.2.1.1 Spectrum Emission Mask for CA (2UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.5.2.1 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.5A.2.1.2 Spectrum Emission Mask for CA (3UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.5.2.1 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.5A.2.1.3 Spectrum Emission Mask for CA (4UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.5.2.1 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.5A.2.1.4 Spectrum Emission Mask for CA (5UL CA) |
TBD |
||||
|
6.5A.2.1.5 Spectrum Emission Mask for CA (6UL CA) |
TBD |
||||
|
6.5A.2.1.6 Spectrum Emission Mask for CA (7UL CA) |
TBD |
||||
|
6.5A.2.1.7 Spectrum Emission Mask for CA (8UL CA) |
TBD |
||||
|
6.5A.2.2.1 Adjacent channel leakage ratio for CA (2UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.5.2.3 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
TT = 0.65 x MTSUIFF + TT due to metric change TT due to metric change : 1.0 dB |
|||
|
6.5A.2.2.2 Adjacent channel leakage ratio for CA (3UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.5.2.3 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
TT = 0.65 x MTSUIFF + TT due to metric change TT due to metric change : 1.0 dB |
|||
|
6.5A.2.2.3 Adjacent channel leakage ratio for CA (4UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.5.2.3 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
TT = 0.65 x MTSUIFF + TT due to metric change TT due to metric change : 1.0 dB |
|||
|
6.5A.2.2.4 Adjacent channel leakage ratio for CA (5UL CA) |
Intra-band contiguous CA 400 MHz < aggregated BW ≤ TBD MHz Intra-band non-contiguous CA TBD |
TBD |
|||
|
6.5A.2.2.5 Adjacent channel leakage ratio for CA (6UL CA) |
Intra-band contiguous CA 400 MHz < aggregated BW ≤ TBD MHz Intra-band non-contiguous CA TBD |
TBD |
|||
|
6.5A.2.2.6 Adjacent channel leakage ratio for CA (7UL CA) |
Intra-band contiguous CA 400 MHz < aggregated BW ≤ TBD MHz Intra-band non-contiguous CA TBD |
TBD |
|||
|
6.5A.2.2.7 Adjacent channel leakage ratio for CA (8UL CA) |
Intra-band contiguous CA 400 MHz < aggregated BW ≤ TBD MHz Intra-band non-contiguous CA TBD |
TBD |
|||
|
6.5A.3.1.1 Transmitter Spurious emissions for CA (2UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.5.3.1 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.5A.3.1.2 Transmitter Spurious emissions for CA (3UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.5.3.1 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.5A.3.1.3 Transmitter Spurious emissions for CA (4UL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 6.5.3.1 Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
6.5A.3.1.4 Transmitter Spurious emissions for CA (5UL CA) |
Intra-band contiguous CA 400 MHz < aggregated BW ≤ TBD MHz Intra-band non-contiguous CA TBD |
TBD |
|||
|
6.5A.3.1.5 Transmitter Spurious emissions for CA (6UL CA) |
Intra-band contiguous CA 400 MHz < aggregated BW ≤ TBD MHz Intra-band non-contiguous CA TBD |
TBD |
|||
|
6.5A.3.1.6 Transmitter Spurious emissions for CA (7UL CA) |
Intra-band contiguous CA 400 MHz < aggregated BW ≤ TBD MHz Intra-band non-contiguous CA TBD |
TBD |
|||
|
6.5A.3.1.7 Transmitter Spurious emissions for CA (8UL CA) |
Intra-band contiguous CA 400 MHz < aggregated BW ≤ TBD MHz Intra-band non-contiguous CA TBD |
TBD |
|||
|
6.5D.2.1 Spectrum Emission Mask for UL MIMO |
Same as 6.5.2.1 |
||||
|
6.5D.2.2 Adjacent channel leakage ratio for UL MIMO |
Same as 6.5.2.3 |
||||
|
6.6.1 Beam correspondence – EIRP |
PC3 1.26 dB (FR2a, FR2b) |
PC3 TT = 0.60 x (MTSUIFF – ΔSNRmr) ΔSNRmr: Systematic offset due to noise when measuring at minimum requirement level |
|||
|
6.6.2 Enhanced Beam correspondence – EIRP |
Same as 6.6.1 |
||||
|
NOTE 1: FR2a: 23.45GHz ≤ f ≤ 32.125GHz |
|||||
F.3.3 Measurement of receiver
Table F.3.3-1: Derivation of Test Requirements (Receiver tests)
|
Sub clause |
Test Tolerance (TT) |
Formula for test requirement |
|||
|
7.3.2 Reference sensitivity power level |
PC3 IFF (Max Device size ≤ 30 cm) 2.34 dB (FR2a, FR2b, NTC) 2.45 dB (FR2a, FR2b, ETC) PC1 IFF (Max Device size ≤ 30 cm) [2.51] dB (FR2a, NTC) TBD dB (FR2a, ETC) |
TT = 0.45 x MTSUIFF |
|||
|
7.3.4 EIS spherical coverage |
PC3 IFF (Max Device size ≤ 30 cm, FR2a, FR2b) 2.21 dB PC1 TBD |
TT = 0.45 x MTSUIFF |
|||
|
7.3A.2.1 Reference sensitivity power level for CA (2DL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 7.3.2 for each component carrier Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
7.3A.2.2 Reference sensitivity power level for CA (3DL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 7.3.2 for each component carrier Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
7.3A.2.3 Reference sensitivity power level for CA (4DL CA) |
Intra-band contiguous CA Maximum aggregated BW ≤ 400MHz Same as 7.3.2 for each component carrier Maximum aggregated BW > 400MHz TBD Intra-band non-contiguous, Inter-band CA TBD |
||||
|
7.3A.2.4 Reference sensitivity power level for CA (5DL CA) |
Intra-band contiguous CA TBD |
||||
|
7.3A.2.5 Reference sensitivity power level for CA (6DL CA) |
Intra-band contiguous CA TBD |
||||
|
7.3A.2.6 Reference sensitivity power level for CA (7DL CA) |
Intra-band contiguous CA TBD |
||||
|
7.3A.2.7 Reference sensitivity power level for CA (8DL CA) |
Intra-band contiguous CA TBD |
||||
|
7.3A.3.1 EIS spherical coverage for CA (2DL CA) |
TBD |
||||
|
7.3A.3.2 EIS spherical coverage for CA (3DL CA) |
TBD |
||||
|
7.3A.3.3 EIS spherical coverage for CA (4DL CA) |
TBD |
||||
|
7.3A.3.4 EIS spherical coverage for CA (5DL CA) |
TBD |
||||
|
7.3A.3.5 EIS spherical coverage for CA (6DL CA) |
TBD |
||||
|
7.3A.3.6 EIS spherical coverage for CA (7DL CA) |
TBD |
||||
|
7.3A.3.7 EIS spherical coverage for CA (8DL CA) |
TBD |
||||
|
7.4 Maximum input level |
TBD |
||||
|
7.4A.1 Maximum input level for CA (2DL CA) |
TBD |
||||
|
7.4A.2 Maximum input level for CA (3DL CA) |
TBD |
||||
|
7.4A.3 Maximum input level for CA (4DL CA) |
TBD |
||||
|
7.4A.4 Maximum input level for CA (5DL CA) |
TBD |
||||
|
7.4A.5 Maximum input level for CA (6DL CA) |
TBD |
||||
|
7.4A.6 Maximum input level for CA (7DL CA) |
TBD |
||||
|
7.4A.7 Maximum input level for CA ((DL CA) |
TBD |
||||
|
7.5 Adjacent channel selectivity |
0 dB |
Wanted signal power + TT T-put limit unchanged |
|||
|
7.5A.1 Adjacent channel selectivity for CA (2UL CA) |
TBD |
||||
|
7.5A.2 Adjacent channel selectivity for CA (3UL CA) |
TBD |
||||
|
7.5A.3 Adjacent channel selectivity for CA (4UL CA) |
TBD |
||||
|
7.5A.4 Adjacent channel selectivity for CA (5UL CA) |
TBD |
||||
|
7.5A.5 Adjacent channel selectivity for CA (6UL CA) |
TBD |
||||
|
7.5A.6 Adjacent channel selectivity for CA (7UL CA) |
TBD |
||||
|
7.5A.7 Adjacent channel selectivity for CA (8UL CA) |
TBD |
||||
|
7.6.2 In-band blocking |
0 dB |
Wanted signal power + TT T-put limit unchanged |
|||
|
7.6A.2.1 In-band blocking for CA (2UL CA) |
TBD |
||||
|
7.6A.2.2 In-band blocking for CA (3UL CA) |
TBD |
||||
|
7.6A.2.3 In-band blocking for CA (4UL CA) |
TBD |
||||
|
7.6A.2.4 In-band blocking for CA (5UL CA) |
TBD |
||||
|
7.6A.2.5 In-band blocking for CA (6UL CA) |
TBD |
||||
|
7.6A.2.6 In-band blocking for CA (7UL CA) |
TBD |
||||
|
7.6A.2.7 In-band blocking for CA (8UL CA) |
TBD |
||||
|
7.9 Spurious emissions |
0 dB |
Minimum requirement + TT T-put limit unchanged |
|||
|
NOTE 1: FR2a, FR2b and FR2c are specified in Table F.3.2-1. |
|||||