Foreword1 Scope2 References3 Definitions, symbols and abbreviations4 Common test environments4.1 Environmental conditions4.2 Common requirements of test equipment4.3 Reference test conditions4.3.1 Test frequencies4.3.2 Radio conditions4.3.3 Physical channel allocations4.3.4 Signal levels4.3.5 Standard test signals4.3.6 Physical layer parameters4.4 Reference system configurations4.4A Test states4.5 Generic procedures4.5A Auxiliary procedures4.5B Common test environment for Vertical UEs4.6 Default NG-RAN RRC message and information elements contents4.6.0 General4.6.1 Contents of RRC messages4.6.1A Contents of PC5 RRC messages4.6.2 System information blocks4.6.2A Positioning System information blocks4.6.3 Radio resource control information elements4.6.4 UE capability information elements4.6.5 Other information elements4.6.6 Sidelink information elements4.6.7 MBS information elements4.7 Default 5GC NAS message and information elements contents4.7.0 General4.7.1 Contents of 5GMM messages4.7.2 Contents of 5GSM messages4.7.3 Contents of EAP-AKA' messages4.7.4 Contents of V2X messages4.7.5 V2X information elements4.7.6 Contents of UE Policy Delivery messages4.7A Default TC message and information element contents4.7B Default AT Command message and information element4.8 Reference configurations4.9 Test procedures4.9.1 Test procedure to check user plane connectivity on DRB#n4.9.2 Test procedure to activate UE Beamlock Test Function (UBF)4.9.3 Test procedure to deactivate UE Beamlock Test Function (UBF)4.9.4 Test procedure to check that UE is in state 5GC RRC_IDLE on a certain NR/NGC cell4.9.5 Test procedure to check that UE is camped on a new NR/NGC cell belonging to a new TA4.9.6 Test procedures for Switch off / Power off UE4.9.7 Test procedure for UE for Tracking area updating / Inter-system change from N1 mode to S1 mode in 5GMM/EMM-IDLE mode4.9.8 Test procedure for Registration Reject4.9.9 Test procedure for UE for Tracking area updating / Inter-system change from S1 mode to N1 mode in 5GMM/EMM-IDLE mode4.9.10 Test procedure to check that the UE is in RRC_CONNECTED state4.9.11 Test procedure for IMS Emergency call or eCall over IMS establishment in 5GC with IMS emergency registration4.9.12 Test procedure for IMS Emergency call establishment in 5GC without IMS emergency registration4.9.12A Test procedure for IMS MO Emergency call release4.9.12B Test procedure for IMS MT Emergency call release4.9.13 Test procedure for no response to paging4.9.14 Void4.9.15 Test procedure for IMS MO speech call establishment in 5GC4.9.16 Test procedure for IMS MT speech call establishment in 5GC4.9.17 Test procedure for IMS MO call release in 5GC4.9.18 Test procedure for IMS MT call release in 5GC4.9.19 Test procedure for IMS MO SMS in 5GC4.9.20 Test procedure for IMS MT SMS in 5GC4.9.21 Test procedure for PDU Session Release4.9.22 Test procedure for establishing unicast mode NR sidelink communication / Initiating UE side4.9.23 Test procedure for establishing unicast mode NR sidelink communication / Peer UE side4.9.24 Test procedure for IMS MO Video call establishment in 5GC4.9.25 Test procedure for UE Configuration Update for transparent UE Policy delivery4.9.26 Test procedure for IMS MT video call establishment in 5GC4.9.27 Test procedure for adding video to a speech call in 5GC4.9.28 Test procedure for removing video from an ongoing call in 5GC4.9.29 Test Procedure for eCall over IMS establishment in 5GS: eCall Only Support4.9.30 Test procedure for releasing unicast mode NR sidelink communication4.9.31 Test procedure to check user plane connectivity on PC5 unicast link4.9.32 Test procedure to activate UE Power Limit Function (UPLF)4.9.33 Test procedure to deactivate UE Power Limit Function (UPLF)4.9.34 Test procedure for MBS Multicast session join and session establishment4.10 Reference configuration for V2X4.11 GNSS Requirements for NR sidelink5 Test environments for RF test5.0 General5.1 Requirements of test equipment5.2 Reference test conditions5.3 Void5.4 Default NG-RAN RRC message and information elements contents5.5 Common procedures for RF testing6 Test environments for Signalling test7 Test environments for RRM testsA.1 Definition of TermsA.2 General Considerations on Connections DiagramA.3 Setup DiagramsA.3.1 Test Equipment Parts for Conducted MeasurementsA.3.1.1 Basic Transmitter/Receiver testsA.3.1.2 Transmitter tests using Spectrum AnalyserA.3.1.3 Transmitter tests using Spectrum Analyser and Signal GeneratorA.3.1.4 Receiver tests using Signal GeneratorA.3.1.5 Receiver tests using Spectrum AnalyserA.3.1.6 Receiver Performance testsA.3.1.7 Demodulation Performance and CSI reporting testsA.3.1.8 RRM tests with more than one NR cellA.3.1.9 Test Equipment supporting NR SidelinkA.3.2 User Equipment Parts for Conducted MeasurementsA.3.2.1 GeneralA.3.2.2 One Antenna ConnectorA.3.2.3 Two Antenna ConnectorsA.3.2.4 Three Antenna ConnectorsA.3.2.5 Four Antenna ConnectorsA.3.2.6 Over Four Antenna ConnectorsA.3.2.7 User Equipment supporting NR SidelinkA.3.3 Test Equipment Parts for Radiated MeasurementsA.3.4 User Equipment Parts for Radiated MeasurementsB.1 GeneralB.2 Permitted Test MethodsB.2.1 GeneralB.2.2 Direct far field (DFF)B.2.3 Direct far field (DFF) setup simplification for centre of beam measurementsB.2.4 Indirect far field (IFF): Compact Antenna Test Range (CATR)B.2.5 Near field to far field transform (NFTF)B.2.6 Enhanced IFFB.2.7 IFF+DFFC.0 GeneralC.1 Definitions and ParametersC.2 Determination of test frequenciesC.3 Determination of SSB and CORESET#0C.4 Determination of SSB and CORESET#0 for RRM testing with SSB SCS 120 kHz and 240 kHzC.5 Determination of test frequencies and S-SSB for V2X bandsC.5.1 GeneralC.5.2 Determination of test frequencies and S-SSB for V2X bandsC.5.2 Determination of test frequencies and S-SSB for V2X bands 4.9.14 Void 38.508-13GPP5GSPart 1: Common test environmentRelease 17TSUser Equipment (UE) conformance specification Tools: ARFCN - Frequency Conversion for 5G NR/LTE/UMTS/GSM