Identifier for DCI formats

Indicating an UL DCI format

"0"

Frequency domain resource assignment

Dependent on test parameters

–

Time domain resource assignment

Indicating the first entry of PUSCH-TimeDomainResourceAllocationList to be used

"0000"

Frequency hopping flag

w/o hopping

"0"

Modulation and coding scheme

Dependent on test parameters

New data indicator

Set for every data transmission/retransmission according to the rules specified in TS 38.321

–

Redundancy version

Dependent on test parameters

–

HARQ process number

Dependent on test parameters

–

TPC command for scheduled PUSCH

0 dB (accumulated TPC) as per Table 7.1.1-1 in TS 38.213

"01"

UL/SUL indicator

Not present (0 bit for UEs not configured with SUL in the cell)

–

Carrier indicator

Not present

–

UL/SUL indicator

Not present (0 bit for UEs not configured with SUL in the cell)

–

1

1

SUL

Identifier for DCI formats

Indicating an UL DCI format

“0”

Bandwidth part indicator

Not present (indicating active BWP, not present in case of only one BWP-Id as per Table 4.6.3-8)

–

Frequency domain resource assignment

Dependent on test parameters

–

Time domain resource assignment

Indicating the first entry of PUSCH-TimeDomainResourceAllocationList to be used

“0000”

Frequency hopping flag

Not present

–

Modulation and coding scheme

Dependent on test parameters

–

New data indicator

Set for every data transmission / retransmission according to the rules specified in TS 38.321 [20]

–

Redundancy version

Dependent on test parameters

–

HARQ process number

Dependent on test parameters

–

1^st downlink assignment index

Dependent on test parameters

2^nd downlink assignment index

Not present (0 bit if one HARQ-ACK sub-codebook)

–

TPC command for scheduled PUSCH

0 dB (accumulated TPC) as per Table 7.1.1-1 in TS 38.213 [22]

“01”

SRS resource indicator

Not present

–

Precoding information and number of layers

Not present (0 bits for 1 antenna port and if the higher layer parameter txConfig = Codebook as per clause 7.3.1.1.2 TS 38.212 [27])

–

2

“10”

2TX_UL_MIMO or ULFPTx_Mode1

Dependent on UE reported full power PMI

1 bit as per Table 7.3.1.1.2-5 in TS 38.212

ULFPTx_Mode2

0 or 1

1 bit

ULFPTx_ModeFull

Antenna ports

Port 0 (NOTE 2)

“000”

“00”

TRANSFORM _PRECODER _ENABLED

SRS request

No aperiodic SRS resource set triggered as per Table 7.3.1.1.2-24 in TS 38.212 (no SUL configured)

“00”

CSI request

Not present

–

CBG transmission information

Not present

–

PTRS-DMRS association

DMRS port 0

“00”

PTRS_UL_CONFIG

Not present

–

beta_offset indicator

Not present (0 bit if the higher layer parameter dynamic in uci-on-PUSCH is not configured)

–

DMRS sequence initialization

= 0 (ScramblingID0 is not present as per Table 4.6.3-50)

“0”

Not present

–

TRANSFORM _PRECODER _ENABLED

UL-SCH indicator

Dependent on test parameters

1 bit. A value of "1" indicates UL-SCH shall be transmitted on the PUSCH and a value of "0" indicates UL-SCH shall not be transmitted on the PUSCH.

–

NOTE 1: codebookSubset = nonCoherent, 2 layers,TPMI = 0 as specified in TS 38.212 [27] Table 7.3.1.1.2-4

NOTE 2: Bitsize depends on transform precoder being enabled/disabled (PUSCH_Config, Table 4.6.3-118) and on dmrs-Type and maxLength (DMRS-UplinkConfig, Table 4.6.3-51); 3 bits (transform precoder disabled) or 2 bits (transform precoder enabled) for DMRS type 1 and len1

2TX_UL_MIMO

UL-MIMO test cases with 2 Tx antenna ports

PTRS_UL_CONFIG

When PTRS Uplink is configured

TRANSFORM_PRECODER_ENABLED

Transform precoding is enabled (PUSCH_Config, Table 4.6.3-118)

SUL

On the SUL carrier when supplementary carrier is configured

ULFPTx_Mode1

UL-MIMO test cases with UEs supporting UL full power transmission Mode-1

ULFPTx_Mode2

UL-MIMO test cases with UEs supporting UL full power transmission Mode-2

ULFPTx_ModeFull

UL-MIMO test cases with UEs supporting UL full power transmission Mode-full power

Identifier for DCI formats

Indicating an UL DCI format

“0”

Carrier indicator

Not present

–

UL/SUL indicator

Not present (0 bit for UEs not configured with SUL in the cell)

–

Bandwidth part indicator

Not present (indicating active BWP, not present in case of only one BWP-Id as per Table 4.6.3-8)

–

Frequency domain resource assignment

Dependent on test parameters

–

Time domain resource assignment

Indicating the first entry of PUSCH-TimeDomainResourceAllocationList to be used

“0000”

Frequency hopping flag

Not present (0 bit if the higher layer parameter frequencyHoppingDCI-0-2 is not configured)

–

Modulation and coding scheme

Dependent on test parameters

–

New data indicator

Set for every data transmission / retransmission according to the rules specified in TS 38.321 [20]

–

Redundancy version

Dependent on test parameters

–

HARQ process number

Dependent on test parameters

–

Downlink assignment index

Not present (0 bit if the higher layer parameter downlinkAssignmentIndexDCI-0-2 is not configured)

TPC command for scheduled PUSCH

0 dB (accumulated TPC) as per Table 7.1.1-1 in TS 38.213 [22]

“01”

SRS resource indicator

Not present

–

Precoding information and number of layers

Not present (0 bits for 1 antenna port and if the higher layer parameter txConfig = Codebook as per clause 7.3.1.1.2 TS 38.212 [27])

–

Antenna ports

Not present (0 bit if higher layer parameter antennaPortsFieldPresenceDCI-0-2 is not configured)

–

SRS request

Not present (0 bit if the higher layer parameter srs-RequestDCI-0-2 is not configured)

–

CSI request

Not present

–

PTRS-DMRS association

DMRS port 0

“00”

PTRS_UL_CONFIG

Not present

–

beta_offset indicator

Not present (0 bit if the higher layer parameter betaOffsets = semiStatic)

–

DMRS sequence initialization

Not present (0 bit if the higher layer parameter dmrs-SequenceInitializationDCI-0-2 is not configured or if transform precoder is enabled)

–

UL-SCH indicator

Dependent on test parameters

1 bit. A value of "1" indicates UL-SCH shall be transmitted on the PUSCH and a value of "0" indicates UL-SCH shall not be transmitted on the PUSCH.

–

Open-loop power control parameter set indication

Not present (0 bit if the higher layer parameter p0-PUSCH-SetList is not configured)

–

Priority indicator

Not present (0 bit if higher layer parameter priorityIndicatorDCI-0-2 is not configured)

–

Invalid symbol pattern indicator

Not present (0 bit if higher layer parameter invalidSymbolPatternIndicatorDCI-0-2 is not configured)

–

NOTE 1: codebookSubset = nonCoherent, 2 layers,TPMI = 0 as specified in TS 38.212 [27] Table 7.3.1.1.2-4

NOTE 2: Bitsize depends on transform precoder being enabled/disabled (PUSCH_Config, Table 4.6.3-118) and on dmrs-Type and maxLength (DMRS-UplinkConfig, Table 4.6.3-51); 3 bits (transform precoder disabled) or 2 bits (transform precoder enabled) for DMRS type 1 and len1

PTRS_UL_CONFIG

When PTRS Uplink is configured

TRANSFORM_PRECODER_ENABLED

Transform precoding is enabled (PUSCH_Config, Table 4.6.3-118)

Identifier for DCI formats

Indicating a DL DCI format

“01”

Frequency domain resource assignment

Dependent on test parameters

–

Time domain resource assignment

Indicating the first entry of PDSCH-TimeDomainResourceAllocationList to be used

“0000”

VRB-to-PRB mapping

Non-interleaved

“0”

Modulation and coding scheme

Dependent on test parameters

–

New data indicator

Set for every data transmission/retransmission according to the rules specified in TS 38.321

–

Redundancy version

Dependent on test parameters

–

HARQ process number

Dependent on test parameters

–

Downlink assignment index

Dependent on test parameters

–

TPC command for scheduled PUCCH

0 dB (accumulated TPC) as per Table 7.2.1-1 in TS 38.213

“01”

PUCCH resource indicator

PUCCH-ResourceId[7] = 6 in pucch-ResourceSetID[1] or PUCCH-ResourceId[7] = 14 in pucch-ResourceSetID[2] as defined in Table 4.6.3-112 (Mapping as per Table 9.2.3-2 in TS 38.213)

“110”

PDSCH-to-HARQ_feedback timing indicator

K₁ slots as specified in 9.2.3 in TS 38.213

µ=0 (SCS=15kHz): K₁=7

‘110’B

µ=1 (SCS=30kHz): K₁=5

‘100’B

µ=3 (SCS=120kHz): K₁=8

‘111’B

Short Messages Indicator

Only scheduling information for Paging is present in the DCI

“01”

Short Messages

Reserved

–

Frequency domain resource assignment

Dependent on test parameters

–

Time domain resource assignment

Indicating the first entry of PDSCH-TimeDomainResourceAllocationList to be used

“0000”

VRB-to-PRB mapping

Non-interleaved

“0”

Modulation and coding scheme

Dependent on test parameters

–

TB scaling

Scaling factor S=1 as defined in Table 5.1.3.2-2 in TS 38.214)

“00”

Reserved bits

Reserved 6 bits

–

Frequency domain resource assignment

Dependent on test parameters

–

–

Time domain resource assignment

Indicating the first entry of Table 5.1.2.1.1-2 in TS 38.214 [21] to be used

“0000”

SIB1

Indicating the first entry of PDSCH-TimeDomainResourceAllocationList to be used

“0000”

SI

VRB-to-PRB mapping

Non-interleaved

“0”

–

Modulation and coding scheme

Dependent on test parameters

–

–

Redundancy version

Dependent on test parameters

–

–

System information indicator

SIB1

“0”

SIB1

SI message

“1”

SI

Reserved bits

Reserved 15 bits

–

–

SIB1

Used for DCI format 1_0 for SIB1

SI

Used for DCI format 1_0 for SI

Frequency domain resource assignment

Dependent on test parameters

–

Time domain resource assignment

Indicating the first entry of PDSCH-TimeDomainResourceAllocationList to be used

“0000”

VRB-to-PRB mapping

Non-interleaved

“0”

Modulation and coding scheme

Dependent on test parameters

–

Redundancy version

Dependent on test parameters

–

TB scaling

Scaling factor S=[1] as defined in Table 5.1.3.2-2 in TS 38.214)

“00”

Reserved bits

Reserved 16 bits

–

Carrier indicator

Not present

–

Identifier for DCI formats

Indicating a DL DCI format

“1”

Bandwidth part indicator

Not present

–

Frequency domain resource assignment

Dependent on test parameters

–

Time domain resource assignment

Indicating the first entry of PDSCH-TimeDomainResourceAllocationList to be used

“0000”

VRB-to-PRB mapping

Non-interleaved

“0”

PRB bundling size indicator

Not present (semi-static PRB_bundling)

–

Rate matching indicator

Not present

–

ZP CSI-RS trigger

Not present

–

Modulation and coding scheme (TB1)

Dependent on test parameters

–

New data indicator (TB1)

Set for every data transmission/retransmission according to the rules specified in TS 38.321 [20]

–

Redundancy version (TB1)

Dependent on test parameters

–

Modulation and coding scheme (TB2)

Dependent on test parameters

–

New data indicator (TB2)

Set for every data transmission/retransmission according to the rules specified in TS 38.321 [20]

–

Redundancy version (TB2)

Dependent on test parameters

–

HARQ process number

Dependent on test parameters

–

Downlink assignment index

Dependent on test parameters

–

TPC command for scheduled PUCCH

0 dB (accumulated TPC) as per Table 7.2.1-1 in TS 38.213 [22]

“01”

PUCCH resource indicator

PUCCH-ResourceId[7] = 6 in pucch-ResourceSetID[1] or PUCCH-ResourceId[7] = 14 in pucch-ResourceSetID[2] as defined in Table 4.6.3-112 (Mapping as per Table 9.2.3-2 in TS 38.213 [22])

“110”

PDSCH-to-HARQ_feedback timing indicator

corresponding to K1 slots as per Table 9.2.3-1 in TS 38.213 [22] and dl-DataToUL-ACK in Table 4.6.3-112

µ=0 (SCS=15kHz): K1=7

“101”

µ=1 (SCS=30kHz): K1=5

“011”

µ=3 (SCS=120kHz): K1=8

“110”

corresponding to K1 slots as per Table 9.2.3-1 in TS 38.213 [22] and dl-DataToUL-ACK in Table 4.6.3-112

For 60KHz SCS

K1 = 4 if mod(i,5) = 0
K1 = 3 if mod(i,5) = 1
K1 = 7 if mod(i,5) = 2
where i is slot index per frame; i = {0,…,39}

For 120KHz SCS

K1 = 4 if mod(i,5) = 0
K1 =3 if mod(i,5) = 1
K1 =7 if mod(i,5) = 2
where i is slot index per frame; i = {0,…,79}

RF_FR2_DL

corresponding to K1 slots as per Table 9.2.3-1 in TS 38.213 [22] and dl-DataToUL-ACK in Table 4.6.3-112

For TDD

K1 = 4 if mod(i,5) = 0
K1 = 3 if mod(i,5) = 1
K1 = 2 if mod(i,5) = 2
where i is slot index per frame; i = {0,…,9}

For FDD

K1 = 2

RF_FR1_15kHz

For TDD

corresponding to K1 slots as per Table 9.2.3-1 in TS 38.213 [22] and dl-DataToUL-ACK in Table 4.6.3-112

K1 = 8 if mod(i,10) = 0
K1 = 7 if mod(i,10) = 1
K1 = 6 if mod(i,10) = 2
K1 = 5 if mod(i,10) = 3
K1 = 4 if mod(i,10) = 4
K1 = 3 if mod(i,10) = 5
K1 = 2 if mod(i,10) = 6
where i is slot index per frame; i = {0,…,19}

For FDD

K1 = 2

RF_FR1_30kHz

corresponding to K1 slots as per Table 9.2.3-1 in TS 38.213 [22] and dl-DataToUL-ACK in Table 4.6.3-112

For TDD

K1 = 13 if mod(i,20) = 2

K1 = 12 if mod(i,20) = 3

K1 = 11 if mod(i,20) = 4

K1 = 10 if mod(i,20) = 5

K1 = 9 if mod(i,20) = 6

K1 = 8 if mod(i,20) = 7

K1 = 7 if mod(i,20) = 8

K1 = 6 if mod(i,20) = 9
K1 = 6 if mod(i,20) = 10

K1 = 6 if mod(i,20) = 11

K1 = 6 if mod(i,20) = 12
K1 = 6 if mod(i,20) = 13
where i is slot index per frame; i = {0,…,39}

For FDD

K1 = 2

RF_FR1_60kHz

Antenna port(s)

DMRS port 0 as per Table 7.3.1.2.2-1 in TS 38.212 [27] (dmrs-Type = DMRS type 1 and maxLength = len1 as per Table 4.6.3-50)

“0000”

“0011”

RF

Transmission configuration indication

Not present (0 bits, tci-PresentInDCI = Not present as per Table 4.6.3-28)

–

SRS request

No aperiodic SRS resource set triggered as per Table 7.3.1.1.2-24 in TS 38.212 [27] (no SUL configured)

“00”

CBG transmission information

Not present

–

CBG flushing out information

Not present

–

DMRS sequence initialization

fix length of 1 bit; ‘0’B for DMRS-DownlinkConfig.scramblingID0 (or physCellId if scramblingID0 is not present); see Table 4.6.3-50

“0”

RF_FR1_15kHz

RF testing in TS 38.521-x for FR1. SCS is set to 15kHz.

RF_FR1_30kHz

RF testing in TS 38.521-x for FR1. SCS is set to 30kHz.

RF_FR1_60kHz

RF testing in TS 38.521-x for FR1. SCS is set to 60kHz.

RF_FR2_DL

RF testing in TS 38.521-x for FR2. SCS is set to 60kHz or 120kHz

RF

RF testing in TS 38.521-x for FR1 and FR2.

Identifier for DCI formats

Indicating a DL DCI format

“1”

Carrier indicator

Not present

Bandwidth part indicator

Not present

–

Frequency domain resource assignment

Dependent on test parameters

–

Time domain resource assignment

Indicating the first entry of PDSCH-TimeDomainResourceAllocationList to be used

“0000”

VRB-to-PRB mapping

Non-interleaved

“0”

PRB bundling size indicator

Not present (semi-static PRB_bundling)

–

Rate matching indicator

Not present

–

ZP CSI-RS trigger

Not present

–

Modulation and coding scheme

Dependent on test parameters

–

New data indicator

Set for every data transmission/retransmission according to the rules specified in TS 38.321 [20]

–

Redundancy version

Dependent on test parameters

–

HARQ process number

Dependent on test parameters

–

Downlink assignment index

Dependent on test parameters

–

TPC command for scheduled PUCCH

0 dB (accumulated TPC) as per Table 7.2.1-1 in TS 38.213 [22]

“01”

PUCCH resource indicator

PUCCH-ResourceId[7] = 6 in pucch-ResourceSetID[1] or PUCCH-ResourceId[7] = 14 in pucch-ResourceSetID[2] as defined in Table 4.6.3-112 (Mapping as per Table 9.2.3-2 in TS 38.213 [22])

“110”

PDSCH-to-HARQ_feedback timing indicator

corresponding to K1 slots as per Table 9.2.3-1 in TS 38.213 [22] and dl-DataToUL-ACK in Table 4.6.3-112

µ=0 (SCS=15kHz): K1=7

“101”

µ=1 (SCS=30kHz): K1=5

“011”

µ=3 (SCS=120kHz): K1=8

“110”

Antenna port(s)

Not present (0 bit if higher layer parameter antennaPortsFieldPresenceDCI-1-2 is not configured)

–

Transmission configuration indication

Not present (0 bits, tci-PresentInDCI = Not present as per Table 4.6.3-28)

–

SRS request

Not present (0 bit if higher layer parameter srs-RequestDCI-1-2 is not configured)

–

DMRS sequence initialization

Not present (0 bit if higher layer parameter dmrs-SequenceInitializationDCI-1-2 is not configured)

–

Priority indicator

Not present (0 bit if higher layer parameter priorityIndicatorDCI-1-2 is not configured)

–

Resource pool index

Not present

–

Time gap

Indicating the first entry of sl-DCI-ToSL-Trans to be used

“000”B

HARQ process number

Dependent on test parameters

–

New data indicator

Set for every data transmission/retransmission according to the rules specified in TS 38.321[20]

–

Lowest index of the subchannel allocation to the initial transmission

Dependent on test parameters

–

Frequency resource assignment

Dependent on test parameters

–

Time resource assignment

only one PSCCH/PSSCH occasion is scheduled per grant

"00000"B

PSFCH-to-HARQ feedback timing indicator

Indicating the first entry of sl-PSFCH-ToPUCCH to be used

"000"B

PUCCH resource indicator

Indicating the first entry of sl-PUCCH-Config to be used

"000"B

Configuration index

Not present

–

SL-RNTI

Indicating the first entry of sl-ConfiguredGrantConfigList to be used

"000"

SL-CS-RNTI

Counter sidelink assignment index

PDCCH monitoring occasions in which DCI format 3_0 scheduling PSSCH transmissions with corresponding PSFCH reception occasions is present, denoted as Y, satisfies (Y-1) mod 4 =0, as specified in 38.213 Table 16.5.2.1-1

"00"

SL-RNTI

UE is configured to monitor DCI format 3_0 with CRC scrambled by SL-RNTI, i.e. dymanic sidelink grant

SL-CS-RNTI

UE is configured to monitor DCI format 3_0 with CRC scrambled by SL-CS-RNTI, i.e. configured sidelink grant

Frequency domain resource assignment

Dependent on test parameters

–

Time domain resource assignment

Indicating the first entry of PDSCH-TimeDomainResourceAllocationList to be used

“0000”

VRB-to-PRB mapping

Non-interleaved

“0”

Modulation and coding scheme

Dependent on test parameters

–

Redundancy version

Dependent on test parameters

–

MCCH change notification

MBS indicates no new MBS service(s) start. LSB indicates no modification of MCCH information other than the change caused by start of new MBS service(s).

“00”

MCCH-RNTI

Not present

–

G-RNTI

NOTE: Zeros shall be appended to DCI format 4_0 until the payload size equals that of DCI format 1_0 monitored in common search space in the same serving cell.

MCCH-RNTI

UE is configured to monitor DCI format 4_0 with CRC scrambled by MCCH-RNTI

G-RNTI

UE is configured to monitor DCI format 4_0 with CRC scrambled by G-RNTI for MTCH

Frequency domain resource assignment

Dependent on test parameters

–

Time domain resource assignment

Indicating the first entry of PDSCH-TimeDomainResourceAllocationList to be used

“0000”

VRB-to-PRB mapping

Non-interleaved

“0”

Modulation and coding scheme

Dependent on test parameters

–

New data indicator

Set for every data transmission/retransmission according to the rules specified in TS 38.321

–

Redundancy version

Dependent on test parameters

–

HARQ process number

Dependent on test parameters

–

Downlink assignment index

Dependent on test parameters

–

PUCCH resource indicator

PUCCH-ResourceId[7] = 6 in pucch-ResourceSetID[1] or PUCCH-ResourceId[7] = 14 in pucch-ResourceSetID[2] as defined in Table 4.6.3-112 (Mapping as per Table 9.2.3-2 in TS 38.213)

“110”

PDSCH-to-HARQ_feedback timing indicator

K₁ slots, dl-DataToUL-ACK-MulticastDciFormat4-1 is not provided, as specified in 9.2.3 in TS 38.213

µ=0 (SCS=15kHz): K₁=7

‘110’B

µ=1 (SCS=30kHz): K₁=5

‘100’B

µ=3 (SCS=120kHz): K₁=8

‘111’B

Reserved bits

Reserved 3 bits

–

Frequency domain resource assignment

Dependent on test parameters

–

Time domain resource assignment

Indicating the first entry of PDSCH-TimeDomainResourceAllocationList to be used

“0000”

VRB-to-PRB mapping

Non-interleaved

“0”

PRB bundling size indicator

Not present (semi-static PRB bundling)

–

Rate matching indicator

Not present

–

ZP CSI-RS trigger

Not present

–

Modulation and coding scheme (TB1)

Dependent on test parameters

–

New data indicator (TB1)

Set for every data transmission/retransmission according to the rules specified in TS 38.321 [20]

–

Redundancy version (TB1)

Dependent on test parameters

–

Modulation and coding scheme (TB2)

Dependent on test parameters

–

New data indicator (TB2)

Set for every data transmission/retransmission according to the rules specified in TS 38.321 [20]

–

Redundancy version (TB2)

Dependent on test parameters

–

HARQ process number

Dependent on test parameters

–

Downlink assignment index

Dependent on test parameters

–

PUCCH resource indicator

PUCCH-ResourceId[7] = 6 in pucch-ResourceSetID[1] or PUCCH-ResourceId[7] = 14 in pucch-ResourceSetID[2] as defined in Table 4.6.3-112 (Mapping as per Table 9.2.3-2 in TS 38.213 [22])

“110”

PDSCH-to-HARQ_feedback timing indicator

corresponding to K1 slots as per Table 9.2.3-1 in TS 38.213 [22] and dl-DataToUL-ACK in Table 4.6.3-112

µ=0 (SCS=15kHz): K1=7

“101”

µ=1 (SCS=30kHz): K1=5

“011”

µ=3 (SCS=120kHz): K1=8

“110”

Antenna port(s)

DMRS port 0 as per Table 7.3.1.2.2-1 in TS 38.212 [27] (dmrs-Type = DMRS type 1 and maxLength = len1 as per Table 4.6.3-50)

“0000”

Transmission configuration indication

Not present (0 bit, tci-PresentInDCI in PDCCH-Config-Multicast is not enabled as per Table 4.6.3-FFS)

–

DMRS sequence initialization

Fix length of 1 bit (configured to physCellId as scramblingID0 is not present in Table 4.6.3-50.

physCellId

Priority indicator

Not present (0 bit, priorityIndicatorDCI-4-2-r17 is not configured in PDSCH-Config-Multicast as per Table 4.6.3-FFS)

–

Enabling/disabling HARQ-ACK feedback indication

Not present (0 bit,

harq-FeedbackEnablerMulticast does not indicates dci-enable as per Table 4.6.3-FFS)

–

NOTE: The size of DCI format 4_2 is configurable by higher layer parameter sizeDCI-4-2 from 20 bits and up to 140 bits.

Priority

Dependent on test parameters

–

Frequency resource assignment

Dependent on test parameters

–

Time domain resource assignment

only one PSCCH/PSSCH occasion is scheduled per grant

"00000"B

Resource reservation period

Not present

–

DMRS pattern

Indicating the first entry of sl-PSSCH-DMRS-TimePatternList-r16 to be used

"0"B

2^nd-stage SCI format

SCI format 2-A

“00”B

SCI format 2-B

“01”B

DISTANCE-BASED HARQ

Beta_offset indicator

Indicating the first entry of sl-BetaOffsets2ndSCI to be used

"00"B

Number of DMRS port

Single port p = 1000 is used

"0"B

Two ports p = 1000 and 1001 are used

"1"B

SL MIMO

Modulation and coding scheme

Dependent on test parameters

–

Additional MCS table indicator

Not present

–

PSFCH overhead indication

"1"B if mod (i, n_PSFCH) = 0

"0"B if mod (i, n_PSFCH ) ≠ 0

where i is the logical slot index belong to resource pool per 1024 frame as specified in 38.214 [21] clause 8.

–

n_PSFCH = 2 OR n_PSFCH = 4 (Note 1)

Not present

Reserved

Number of reserved bits is given by sl-NumReservedBits-r16

"00"

DISTANCE-BASED HARQ

For distance-based HARQ test

SL MIMO

For SL MIMO test

HARQ process number

Dependent on test parameters

New data indicator

Set for every data transmission/retransmission according to the rules specified in TS 38.321

–

Redundancy version

Dependent on test parameters

–

Source ID

Dependent on test parameters

–

Destination ID

Dependent on test parameters

–

HARQ feedback enabled/disabled indicator

HARQ feedback is enabled

“1”B

Cast type indicator

broadcast

"00"B

BROADCAST

groupcast with ACK/NACK HARQ

"01"B

GROUPCAST_ACK_NACK

unicast

"10"B

UNICAST

groupcast with NACK-only HARQ

"11"B

GROUPCAST_NACK_ONLY

CSI request

Not ask for SL CSI report

"0"B

Ask for SL CSI report

"1"B

SL_CSI

BROADCAST

For broadcast SL communication test

GROUPCAST_ACK_NACK

For groupcast SL communication with ACK/NACK HARQ feedback test

GROUPCAST_NACK_ONLY

For groupcast SL communication with NACK-only HARQ feedback test

UNICAST

For unicast SL communication test

SL_CSI

For SL CSI reporting test

HARQ process number

Dependent on test parameters

–

New data indicator

Set for every data transmission/retransmission according to the rules specified in TS 38.321

–

Redundancy version

Dependent on test parameters

–

Source ID

Dependent on test parameters

–

Destination ID

Dependent on test parameters

–

HARQ feedback enabled/disabled indicator

HARQ feedback enabled

“1”B

Zone ID

Dependent on test parameters

–

Communication range requirement

Indicating the first entry of sl-ZoneConfigMCR-List to be used

"0000"B