4.7.2 Contents of 5GSM messages
38.508-13GPP5GSPart 1: Common test environmentRelease 17TSUser Equipment (UE) conformance specification
– PDU session establishment request
Table 4.7.2-1: PDU SESSION ESTABLISHMENT REQUEST
|
Derivation Path: 24.501 clause 8.3.1 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
Any value according to TS 24.501 [25] subclause 9.4 |
|||
|
PTI |
Any value from 1 to 254 |
|||
|
PDU SESSION ESTABLISHMENT REQUEST message identity |
‘1100 0001’B |
|||
|
Integrity protection maximum data rate |
Present but contents not checked |
|||
|
PDU session type |
Any value between ‘001’B, ‘010’B, ‘011’B and ‘101’B |
The allowed values are respectively IPv4, IPv6, IPv4v6 and Ethernet (EtherType as defined in IEEE 802.3) |
||
|
SSC mode |
If present: contents not checked |
|||
|
5GSM capability |
If present: contents not checked |
|||
|
Maximum number of supported packet filters |
If present: contents not checked |
|||
|
Always-on PDU session requested |
If present: contents not checked |
|||
|
Always-on PDU session requested |
SST_URLLC |
|||
|
APSR |
‘1’B |
Always-on PDU session requested |
||
|
SM PDU DN request container |
If present: contents not checked |
|||
|
Extended protocol configuration options |
If present: contents not checked |
The SS shall remember if this IE is present and its contents because this affects subsequent SS behaviour, e.g. coding of PDU SESSION ESTABLISHMENT ACCEPT. |
||
|
Extended protocol configuration options |
Present including at least the following container |
DATA_OFF |
||
|
Container ID n |
‘0017’H |
3GPP PS data off UE status |
||
|
Length of container ID n contents |
1 octet |
|||
|
Container ID n contents |
‘01’H |
‘deactivated’ |
||
|
IP header compression configuration |
If present: contents not checked |
|||
|
DS-TT Ethernet port MAC address |
If present: contents not checked |
|||
|
UE-DS-TT residence time |
If present: contents not checked |
|||
|
Port management information container |
If present: contents not checked |
|||
|
Ethernet header compression configuration |
If present: contents not checked |
|||
|
Suggested interface identifier |
If present: contents not checked |
|||
|
Service-level-AA container |
If present: contents not checked |
|||
|
Requested MBS container |
If present: contents not checked |
|||
|
PDU session pair ID |
If present: contents not checked |
|||
|
RSN |
If present: contents not checked |
|||
|
Condition |
Explanation |
|
DATA_OFF |
If the UE supports 3GPP PS data off as specified in TS 38.508-2 [10], Table A.4.3.7-1/xx |
– PDU session establishment accept
Table 4.7.2-2: PDU SESSION ESTABLISHMENT ACCEPT
|
Derivation Path: 24.501 clause 8.3.2 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
The same value as the value set in PDU SESSION ESTABLISHMENT REQUEST message |
|||
|
PTI |
The same value as the value set in PDU SESSION ESTABLISHMENT REQUEST message |
|||
|
PDU SESSION ESTABLISHMENT ACCEPT message identity |
‘1100 0010’B |
|||
|
Selected PDU session type |
‘001’B |
IPv4 |
||
|
‘010’B |
IPv6 |
|||
|
‘011’B |
IPv4v6 |
|||
|
‘101’B |
Ethernet |
|||
|
Selected SSC mode |
‘001’B |
SSC mode 1 |
||
|
Authorized QoS rules |
5GC QoS rule of the entry in Table 4.8.4-1 which has been determined by the DNN IE in the UL NAS TRANSPORT message which carried the corresponding PDU SESSION ESTABLISHMENT REQUEST or by pc_APN_Default_Configuration if the DNN IE was not present |
|||
|
Session AMBR |
||||
|
Unit for Session-AMBR for downlink |
‘000 00101’ |
Value is incremented in multiples of 256 Kbps |
||
|
Session-AMBR for downlink |
‘0000 0000 0000 0100’B |
1024 Kbps |
||
|
Unit for Session-AMBR for uplink |
‘000 00101’ |
Value is incremented in multiples of 256 Kbps |
||
|
Session-AMBR for uplink |
‘0000 0000 0000 0100’B |
1024 Kbps |
||
|
5GSM cause |
Not Present |
|||
|
PDU address |
IPv4 |
|||
|
Length of PDU address contents |
5 octets |
|||
|
PDU type value |
‘001’B |
IPv4 |
||
|
PDU address information |
IPv4 address |
The SS provides a valid IPv4 address |
NOT IPv4-DHCP |
|
|
0.0.0.0 |
DHCPv4 is to be used to allocate the IPv4 address |
IPv4-DHCP |
||
|
PDU address |
IPv6 |
|||
|
Length of PDU address contents |
9 octets |
|||
|
PDU type value |
‘010’B |
IPv6 |
||
|
PDU address information |
IPv6 interface identifier |
The SS provides a valid IPv6 interface identifier |
||
|
PDU address |
IPv4v6 |
|||
|
Length of PDU address contents |
13 octets |
|||
|
PDU type value |
‘011’B |
IPv4v6 |
||
|
PDU address information (Octets 4 to 11) |
IPv6 interface identifier |
The SS provides a valid IPv6 interface identifier |
||
|
PDU address information (Octets 12 to 15) |
IPv4 address |
The SS provides a valid IPv4 address |
NOT IPv4-DHCP |
|
|
0.0.0.0 |
DHCPv4 is to be used to allocate the IPv4 address |
IPv4-DHCP |
||
|
RQ timer value |
Not Present |
|||
|
S-NSSAI |
||||
|
Length of S-NSSAI contents |
‘0000 0001’B |
SST |
||
|
SST |
‘0000 0001’B |
SST value 1 (eMBB) |
SST_eMBB |
|
|
SST |
‘0000 0010’B |
SST value 2 (URLLC) |
SST_URLLC |
|
|
SST |
‘0000 0011’B |
SST value 3 (MIoT) |
SST_MIoT |
|
|
SST |
‘0000 0100’B |
SST value 4 (V2X) |
SST_V2X |
|
|
Always-on PDU session indication |
Not Present |
|||
|
Always-on PDU session indication |
||||
|
APSI |
‘0’B |
Always-on PDU session not allowed |
Always_On_Requested |
|
|
APSI |
‘1’B |
Always-on PDU session required |
Always_On_Requested AND SST_URLLC |
|
|
Mapped EPS bearer contexts |
Not Present |
|||
|
Mapped EPS bearer contexts |
Interworking_with_EPS |
|||
|
Mapped EPS bearer context |
||||
|
EPS bearer identity |
The same value as the one specified in the Reference QoS flow referred to from the Reference QoS rule indicated in the IE Authorized QoS rules |
|||
|
Operation code |
‘001’B |
Create new EPS bearer |
||
|
E bit |
‘1’B |
Parameters list is included |
||
|
Number of EPS parameters |
’0001’B |
1 parameter |
||
|
Mapped EPS QoS parameters |
EPC default bearer context of the entry in Table 4.8.4-1 which has been determined by the DNN IE in the UL NAS TRANSPORT message which carried the corresponding PDU SESSION ESTABLISHMENT REQUEST or by pc_APN_Default_Configuration if the DNN IE was not present |
|||
|
EAP message |
Not Present |
|||
|
Authorized QoS flow descriptions |
The QoS flow referred to in the relevant Authorized QoS rules IE |
|||
|
Extended protocol configuration options |
Not Present |
|||
|
Extended protocol configuration options |
P-CSCF_IPv6 OR P-CSCF_IPv4 |
|||
|
Container ID 1 |
‘0001’H |
P-CSCF_IPv6 |
||
|
Length of container ID 1 contents |
Length value determined by testimplementation |
|||
|
Container ID 1 contents |
IPv6 address |
P-CSCF IPv6 Address |
||
|
Container ID 2 |
‘000C’H |
P-CSCF_IPv4 |
||
|
Length of container ID 2 contents |
Length value determined by test implementation |
|||
|
Container ID 2 contents |
IPv4 address |
P-CSCF IPv4 Address |
||
|
Container ID 3 |
‘0001’H |
Additional_P-CSCF_IPv6 |
||
|
Length of container ID 3 contents |
Length value determined by testimplementation |
|||
|
Container ID 3 contents |
IPv6 address |
Additional P-CSCF IPv6 Address |
||
|
Container ID 4 |
‘000C’H |
Additional_P-CSCF_IPv4 |
||
|
Length of container ID 4 contents |
Length value determined by test implementation |
|||
|
Container ID 4 contents |
IPv4 address |
Additional P-CSCF IPv4 Address |
||
|
Container ID n |
‘0003’H |
n assigned to next available number |
DNS IPv6 |
|
|
Length of container ID n contents |
Length value determined by the TTCN implementation |
|||
|
Container ID n contents |
IPv6 address |
DNS IPv6 address |
||
|
Container ID n+1 |
‘000D’H |
n assigned to next available number |
DNS IPv4 |
|
|
Length of container ID n contents |
Length value determined by the TTCN implementation |
|||
|
Container ID n contents |
IPv4 address |
DNS IPv4 address |
||
|
DNN |
The DNN/APN ID of the entry in Table 4.8.4-1 which has been determined by the DNN IE in the UL NAS TRANSPORT message which carried the corresponding PDU SESSION ESTABLISHMENT REQUEST or by pc_APN_Default_Configuration if the DNN IE was not present |
|||
|
5GSM network feature support |
Not Present |
|||
|
Serving PLMN rate control |
Not Present |
|||
|
ATSSS container |
Not Present |
|||
|
Control plane only indication |
Not Present |
|||
|
IP header compression configuration |
Not Present |
|||
|
Ethernet header compression configuration |
Not Present |
|||
|
Service-level-AA container |
Not Present |
|||
|
Received MBS container |
Not Present |
|||
|
Condition |
Explanation |
|
IPv4 |
If in the last PDU SESSION ESTABLISHMENT REQUEST sent prior to this message, the PDU session type = ‘001’B |
|
IPv6 |
If in the last PDU SESSION ESTABLISHMENT REQUEST sent prior to this message, the PDU session type = ‘010’B |
|
IPv4v6 |
If in the last PDU SESSION ESTABLISHMENT REQUEST sent prior to this message, the PDU session type = ‘011’B |
|
IPv4-DHCP |
If in the last PDU SESSION ESTABLISHMENT REQUEST sent prior to this message, the IE Extended protocol configuration options contains a configuration protocol option = ‘000BH’ ("IPv4 address allocation via DHCPv4", length of contents = 0). Note: This condition is used in conjunction with IPv4 or IPv4v6 as indicated in the "PDU address information" just above. |
|
Ethernet |
If in the last PDU SESSION ESTABLISHMENT REQUEST sent prior to this message, the PDU session type = ‘101’B. |
|
Always_On_Requested |
If the last PDU SESSION ESTABLISHMENT REQUEST message included the Always-on PDU session requested IE |
|
P-CSCF_IPv6 |
If in the last PDU SESSION ESTABLISHMENT REQUEST sent prior to this message the IE Extended protocol configuration options contains a configuration protocol option = ‘0001H’ (“P-CSCF IPv6 Address Request", length of contents = 0) |
|
P-CSCF_IPv4 |
If in the last PDU SESSION ESTABLISHMENT REQUEST sent prior to this message the IE Extended protocol configuration options contains a configuration protocol option = ‘000CH’ (“P-CSCF IPv4 Address Request", length of contents = 0) |
|
Interworking_with_EPS |
If the UE has indicated support of S1, then the SS shall include this IE to provide details for the interworking with EPS being supported for a PDU session. This requirement is set up for the purpose of facilitating the test description. It is not mandatory for the Network to support Mapped EPS bearer contexts. |
|
Additional_P-CSCF_IPv6 |
P-CSCF_IPv6 AND SS requires to be configured with second P-CSCF Ipv6 address |
|
Additional _P-CSCF_IPv4 |
P-CSCF_IPv6 AND SS requires to be configured with second P-CSCF Ipv4 address |
|
DNS IPv6 |
If in the last PDU Session Establishment REQUEST the Extended protocol configuration options was included with a “DNS IPv6 Address Request”. |
|
DNS IPv4 |
If in the last PDU Session Establishment REQUEST the Extended protocol configuration options was included with a “DNS IPv4 Address Request”. |
– PDU session establishment reject
Table 4.7.2-3: PDU SESSION ESTABLISHMENT REJECT
|
Derivation Path: 24.501 clause 8.3.3 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
The same value as the value set in PDU SESSION ESTABLISHMENT REQUEST message |
|||
|
PTI |
The same value as the value set in PDU SESSION ESTABLISHMENT REQUEST message |
|||
|
PDU SESSION ESTABLISHMENT REJECT message identity |
‘1100 0011’B |
|||
|
5GSM cause |
The value is set according to specific message content |
|||
|
Back-off timer value |
Not Present |
|||
|
Allowed SSC mode |
Not Present |
|||
|
EAP message |
Not Present |
|||
|
5GSM congestion re-attempt indicator |
Not Present |
|||
|
Extended protocol configuration options |
Not Present |
|||
|
Re-attempt indicator |
Not Present |
|||
|
Service-level-AA container |
Not Present |
|||
– PDU session authentication command
Table 4.7.2-4: PDU SESSION AUTHENTICATION COMMAND
|
Derivation Path: 24.501 clause 8.3.4 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
Set according to specific message content |
|||
|
PTI |
‘0000 0000’B |
No procedure transaction identity assigned |
||
|
PDU SESSION AUTHENTICATION COMMAND message identity |
‘1100 0101’B |
|||
|
EAP message |
Set according to TS 38.508 Table 4.7.3.2-1 |
See TS 24.501 [25] subclause 9.11.2.2 |
||
|
Extended protocol configuration options |
Not Present |
|||
|
Remote UE handling information list |
Not Present |
|||
– PDU session authentication complete
Table 4.7.2-5: PDU SESSION AUTHENTICATION COMPLETE
|
Derivation Path: 24.501 clause 8.3.5 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
The value indicated in PDU SESSION AUTHENTICATION COMMAND message |
|||
|
PTI |
‘0000 0000’B |
No procedure transaction identity assigned |
||
|
PDU SESSION AUTHENTICATION COMPLETE message identity |
‘1100 0110’B |
|||
|
EAP message |
Set according to TS 38.508 Table 4.7.3.2-2 |
See TS 24.501 [25] subclause 9.11.2.2 |
||
|
Extended protocol configuration options |
If present: contents not checked |
|||
|
Remote UE handling information list |
If present: contents not checked |
|||
– PDU session authentication result
Table 4.7.2-6: PDU SESSION AUTHENTICATION RESULT
|
Derivation Path: 24.501 clause 8.3.6 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
The value indicated in PDU SESSION AUTHENTICATION COMMAND message |
|||
|
PTI |
‘0000 0000’B |
No procedure transaction identity assigned |
||
|
PDU SESSION AUTHENTICATION RESULT message identity |
‘1100 0111’B |
|||
|
EAP message |
Set according to specific message content |
See TS 24.501 [25] subclause 9.11.2.2 |
||
|
Extended protocol configuration options |
Not Present |
|||
– PDU session modification request
Table 4.7.2-7: PDU SESSION MODIFICATION REQUEST
|
Derivation Path: 24.501 clause 8.3.7 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
The value indicated in PDU SESSION ESTABLISHMENT REQUEST message |
|||
|
PTI |
Any value from 1 to 254 |
|||
|
PDU SESSION MODIFICATION REQUEST message identity |
‘1100 1001’B |
|||
|
5GSM capability |
If present: contents not checked |
|||
|
5GSM cause |
If present: contents not checked |
|||
|
Maximum number of supported packet filters |
If present: contents not checked |
|||
|
Always-on PDU session requested |
If present: contents not checked |
|||
|
Integrity protection maximum data rate |
If present: contents not checked |
|||
|
Requested QoS rules |
If present: contents not checked |
|||
|
Requested QoS flow descriptions |
If present: contents not checked |
|||
|
Mapped EPS bearer contexts |
If present: contents not checked |
|||
|
Extended protocol configuration options |
If present: contents not checked |
|||
|
Port management information container |
If present: contents not checked |
|||
|
IP header compression configuration |
If present: contents not checked |
|||
|
Ethernet header compression configuration |
If present: contents not checked |
|||
|
Requested MBS container |
If present: contents not checked |
|||
|
Service-level-AA container |
If present: contents not checked |
|||
– PDU session modification reject
Table 4.7.2-8: PDU SESSION MODIFICATION REJECT
|
Derivation Path: 24.501 clause 8.3.8 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
The value indicated in PDU SESSION MODIFICATION REQUEST message. |
|||
|
PTI |
The value indicated in PDU SESSION MODIFICATION REQUEST message. |
|||
|
PDU SESSION MODIFICATION REJECT message identity |
‘1100 1010’B |
|||
|
5GSM cause |
Set according to specific message content. |
|||
|
Back-off timer value |
Not Present |
|||
|
5GSM congestion re-attempt indicator |
Not Present |
|||
|
Extended protocol configuration options |
Not Present |
|||
|
Re-attempt indicator |
Not Present |
|||
– PDU session modification command
Table 4.7.2-9: PDU SESSION MODIFICATION COMMAND
|
Derivation Path: 24.501 clause 8.3.9 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
Set according to specific message content. |
|||
|
PDU session ID |
The value indicated in PDU SESSION MODIFICATION REQUEST message. |
UE_Initiated_Modification |
||
|
PTI |
‘0000 0000’B |
No procedure transaction identity assigned |
||
|
PTI |
The value indicated in PDU SESSION MODIFICATION REQUEST message. |
UE_Initiated_Modification |
||
|
PDU SESSION MODIFICATION COMMAND message identity |
‘1100 1011’B |
|||
|
5GSM cause |
Not Present |
|||
|
Session AMBR |
Not Present |
|||
|
RQ timer value |
Not Present |
|||
|
Always-on PDU session indication |
Not Present |
|||
|
Always-on PDU session indication |
||||
|
APSI |
‘0’B |
Always-on PDU session not allowed |
Always_On_Requested |
|
|
APSI |
‘1’B |
Always-on PDU session required |
Always_On_Requested AND SST_URLLC |
|
|
Authorized QoS rules |
Not Present |
|||
|
Mapped EPS bearer contexts |
Not Present |
|||
|
Authorized QoS flow descriptions |
Not Present |
|||
|
Extended protocol configuration options |
Not Present |
|||
|
ATSSS container |
Not Present |
|||
|
IP header compression configuration |
Not Present |
|||
|
Port management information container |
Not Present |
|||
|
Serving PLMN rate control |
Not Present |
|||
|
Ethernet header compression configuration |
Not Present |
|||
|
Received MBS container |
Not Present |
|||
|
Service-level-AA container |
Not Present |
|||
|
Condition |
Explanation |
|
Always_On_Requested |
If the last PDU SESSION MODIFICATION REQUEST message included the Always-on PDU session requested IE |
|
UE_Initiated_Modification |
If this message was triggered by a PDU SESSION MODIFICATION REQUEST message sent by the UE |
– PDU session modification complete
Table 4.7.2-10: PDU SESSION MODIFICATION COMPLETE
|
Derivation Path: 24.501 clause 8.3.10 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
The value indicated in PDU SESSION MODIFICATION COMMAND message |
|||
|
PTI |
‘0000 0000’B |
No procedure transaction identity assigned |
||
|
PTI |
The value indicated in PDU SESSION MODIFICATION REQUEST message. |
UE_Initiated_Modification |
||
|
PDU SESSION MODIFICATION COMPLETE message identity |
‘1100 1100’B |
|||
|
Extended protocol configuration options |
If present: contents not checked |
|||
|
Port management information container |
If present: contents not checked |
|||
|
Condition |
Explanation |
|
UE_Initiated_Modification |
If this message was triggered by a PDU SESSION MODIFICATION REQUEST message sent by the UE |
– PDU session modification command reject
Table 4.7.2-11: PDU SESSION MODIFICATION COMMAND REJECT
|
Derivation Path: 24.501 clause 8.3.11 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
The value indicated in PDU SESSION MODIFICATION COMMAND message |
|||
|
PTI |
‘0000 0000’B |
No procedure transaction identity assigned |
||
|
PDU SESSION MODIFICATION COMMAND REJECT message identity |
‘1100 1101’B |
|||
|
5GSM cause |
If present: contents not checked |
|||
|
Extended protocol configuration options |
If present: contents not checked |
|||
– PDU session release request
Table 4.7.2-12: PDU SESSION RELEASE REQUEST
|
Derivation Path: 24.501 clause 8.3.12 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
The value indicated in PDU SESSION ESTABLISHMENT REQUEST message |
|||
|
PTI |
Any value from 1 to 254 |
|||
|
PDU SESSION RELEASE REQUEST message identity |
‘1101 0001’B |
|||
|
5GSM cause |
If present: contents not checked |
|||
|
Extended protocol configuration options |
If present: contents not checked |
|||
– PDU session release reject
Table 4.7.2-13: PDU SESSION RELEASE REJECT
|
Derivation Path: 24.501 clause 8.3.13 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
The value indicated in PDU SESSION RELEASE REQUEST message. |
|||
|
PTI |
The value indicated in PDU SESSION RELEASE REQUEST message. |
|||
|
PDU SESSION RELEASE REJECT message identity |
‘1101 0010’B |
|||
|
5GSM cause |
Set according to specific message content. |
|||
|
Extended protocol configuration options |
Not Present |
|||
– PDU session release command
Table 4.7.2-14: PDU SESSION RELEASE COMMAND
|
Derivation Path: 24.501 clause 8.3.14 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
Set according to specific message content. |
|||
|
PTI |
‘0000 0000’B |
No procedure transaction identity assigned |
||
|
PDU SESSION RELEASE COMMAND message identity |
‘1101 0011’B |
|||
|
5GSM cause |
‘0001 1010’B |
Insufficient resources |
||
|
Back-off timer value |
Not Present |
|||
|
EAP message |
Not Present |
|||
|
5GSM congestion re-attempt indicator |
Not Present |
|||
|
Extended protocol configuration options |
Not Present |
|||
|
Access type |
Not Present |
|||
|
Service-level-AA container |
Not Present |
|||
– PDU session release complete
Table 4.7.2-15: PDU SESSION RELEASE COMPLETE
|
Derivation Path: 24.501 clause 8.3.15 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
The value indicated in PDU SESSION RELEASE COMMAND message. |
|||
|
PTI |
‘0000 0000’B |
No procedure transaction identity assigned |
||
|
PDU SESSION RELEASE COMPLETE message identity |
‘1101 0100’B |
|||
|
5GSM cause |
If present: contents not checked |
|||
|
Extended protocol configuration options |
If present: contents not checked |
|||
– 5GSM status
Table 4.7.2-16: 5GSM STATUS
|
Derivation Path: 24.501 clause 8.3.16 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
Set according to specific message content. |
|||
|
PTI |
Set according to specific message content. |
|||
|
5GSM STATUS message identity |
‘1101 0110’B |
|||
|
5GSM cause |
Set according to specific message content. |
|||
– Service-level authentication command
Table 4.7.2-17: SERVICE-LEVEL AUTHENTICATION COMMAND
|
Derivation Path: 24.501 clause 8.3.17 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
Set according to specific message content. |
|||
|
PTI |
Set according to specific message content. |
|||
|
SERVICE-LEVEL AUTHENTICATION COMMAND message identity |
‘1101 1000’B |
|||
|
Service-level-AA container |
FFS |
|||
– Service-level authentication complete
Table 4.7.2-18: SERVICE-LEVEL AUTHENTICATION COMPLETE
|
Derivation Path: 24.501 clause 8.3.18 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
Set according to specific message content. |
|||
|
PTI |
Set according to specific message content. |
|||
|
SERVICE-LEVEL AUTHENTICATION COMPLETE message identity |
‘1101 1001’B |
|||
|
Service-level-AA container |
FFS |
|||
– Remote UE report
Table 4.7.2-19: REMOTE UE REPORT
|
Derivation Path: 24.501 clause 8.3.19 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
Set according to specific message content. |
|||
|
PTI |
Set according to specific message content. |
|||
|
REMOTE UE REPORT message identity |
‘1101 1010’B |
|||
|
Remote UE context connected |
FFS |
|||
|
Remote UE context disconnected |
FFS |
|||
– Remote UE report response
Table 4.7.2-20: REMOTE UE REPORT RESPONSE
|
Derivation Path: 24.501 clause 8.3.20 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Extended protocol discriminator |
‘0010 1110’B |
5GS session management messages |
||
|
PDU session ID |
Set according to specific message content. |
|||
|
PTI |
Set according to specific message content. |
|||
|
REMOTE UE REPORT RESPONSE message identity |
‘1101 1011’B |
|||
|
EAP message |
FFS |
|||
|
Remote UE handling information list |
FFS |
|||
|
Authorized QoS flow descriptions |
FFS |
|||