7.6 Blocking
36.1043GPPBase Station (BS) radio transmission and receptionEvolved Universal Terrestrial Radio Access (E-UTRA)Release 18TS
7.6.1 General blocking requirement
The blocking characteristics is a measure of the receiver ability to receive a wanted signal at its assigned channel in the presence of an unwanted interferer, which are either a 1.4MHz, 3MHz or 5MHz E-UTRA signal for in-band blocking or a CW signal for out-of-band blocking. The interfering signal shall be an E-UTRA signal as specified in Annex C.
7.6.1.1 Minimum requirement
For E-UTRA, the throughput shall be ≥ 95% of the maximum throughput of the reference measurement channel, with a wanted and an interfering signal coupled to BS antenna input using the parameters in Tables 7.6.1.1-1, 7.6.1.1-1a, 7.6.1.1-1b, 7.6.1.1-1c and 7.6.1.1-2. The reference measurement channel for the wanted signal is identified in Table 7.2.1-1, 7.2.1-2, 7.2.1-3 and 7.2.1-4 for each channel bandwidth and further specified in Annex A.
The blocking requirement is applicable outside the Base Station RF Bandwidth or Radio Bandwidth. The interfering signal offset is defined relative to the Base Station RF Bandwidth edges or Radio Bandwidth edges.
For a BS operating in non-contiguous spectrum within any operating band, the blocking requirement applies in addition inside any sub-block gap, in case the sub-block gap size is at least as wide as twice the interfering signal minimum offset in Table 7.6.1.1-2. The interfering signal offset is defined relative to the sub-block edges inside the sub-block gap.
For a BS capable of multi-band operation, the requirement in the in-band blocking frequency ranges applies for each supported operating band. The requirement applies in addition inside any Inter RF Bandwidth gap, in case the Inter RF Bandwidth gap size is at least as wide as twice the interfering signal minimum offset in Table 7.6.1.1-2.
For a BS capable of multi-band operation, the requirement in the out-of-band blocking frequency ranges apply for each operating band, with the exception that the in-band blocking frequency ranges of all supported operating bands according to Tables 7.6.1.1-1, 7.6.1.1-1a and 7.6.1.1-1c shall be excluded from the out-of-band blocking requirement.
Table 7.6.1.1-1: Blocking performance requirement for Wide Area BS for E-UTRA
Operating Band |
Centre Frequency of Interfering Signal [MHz] |
Interfering Signal mean power [dBm] |
Wanted Signal mean power [dBm] |
Interfering signal centre frequency minimum frequency offset from the lower/upper Base Station RF Bandwidth edge or sub-block edge inside a sub-block gap [MHz] |
Type of Interfering Signal |
||
1-7, 9-11, 13, 14, 18,19, 21-23, 24, 27, 30, 33-45, 48, 50, 52, 54, 65, 66, 68, 70 |
(FUL_low -20) |
to |
(FUL_high +20) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +20) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
8, 26, 28 |
(FUL_low -20) |
to |
(FUL_high +10) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +10) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
12 |
(FUL_low -20) |
to |
(FUL_high +13) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +13) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
17 |
(FUL_low -20) |
to |
(FUL_high +18) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +18) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
20, 71 |
(FUL_low -11) |
to |
(FUL_high +20) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +20) |
to to |
(FUL_low -11) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
25 |
(FUL_low -20) |
to |
(FUL_high +15) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +15) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
31, 72, 73, 74, 87, 88 |
(FUL_low -20) |
to |
(FUL_high +5) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +5) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
85 |
(FUL_low -20) |
to |
(FUL_high +12) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +12) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
Note 1: PREFSENS depends on the channel bandwidth as specified in Table 7.2.1-1. Note 2: For a BS capable of multiband operation, in case of interfering signal that is not in the in-band blocking frequency range of the operating band where the wanted signal is present, and not in the in-band blocking frequency range of an adjacent or overlapping operating band, the wanted signal mean power is equal to PREFSENS + 1.4 dB. |
NOTE: Table 7.6.1.1-1 assumes that two operating bands, where the downlink operating band (see Table 5.5-1) of one band would be within the in-band blocking region of the other band, are not deployed in the same geographical area.
Table 7.6.1.1-1a: Blocking performance requirement for Local Area BS for E-UTRA
Operating Band |
Centre Frequency of Interfering Signal [MHz] |
Interfering Signal mean power [dBm] |
Wanted Signal mean power [dBm] |
Interfering signal centre frequency minimum frequency offset from the lower/upper Base Station RF Bandwidth edge or sub-block edge inside a sub-block gap [MHz] |
Type of Interfering Signal |
||
1-7, 9-11, 13-14, 18,19, 21-23, 24, 27, 30, 33-45, 48-54, 65, 66, 68, 70 |
(FUL_low -20) |
to |
(FUL_high +20) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +20) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
8, 26, 28 |
(FUL_low -20) |
to |
(FUL_high +10) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +10) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
12 |
(FUL_low -20) |
to |
(FUL_high +13) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +13) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
17 |
(FUL_low -20) |
to |
(FUL_high +18) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1. 1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +18) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
20, 71 |
(FUL_low -11) |
to |
(FUL_high +20) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1. 1-2 |
See table 7.6.1.1-2 |
1 |
to |
(FUL_low -11) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
(FUL_high +20) |
to |
||||||
25 |
(FUL_low -20) |
to |
(FUL_high +15) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1. 1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +15) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
31, 72, 73, 74, 87, 88 |
(FUL_low -20) |
to |
(FUL_high +5) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +5) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
46 |
(FUL_low -20) |
to |
(FUL_high +20) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
(FUL_low -500) (FUL_high +20) |
to to |
(FUL_low -20) (FUL_high +500) |
-35 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
1 (FUL_high +500) |
to to |
(FUL_low -500) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
85 |
(FUL_low -20) |
to |
(FUL_high +12) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1. 1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +12) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
Note 1: PREFSENS depends on the channel bandwidth as specified in Table 7.2.1-2 Note 2: For a BS capable of multiband operation, in case of interfering signal that is not in the in-band blocking frequency range of the operating band where the wanted signal is present, and not in the in-band blocking frequency range of an adjacent or overlapping operating band, the wanted signal mean power is equal to PREFSENS + 1.4 dB. |
NOTE: Table 7.6.1.1-1a assumes that two operating bands, where the downlink operating band (see Table 5.5-1) of one band would be within the in-band blocking region of the other band, are not deployed in the same geographical area.
Table 7.6.1.1-1b: Blocking performance requirement for Home BS for E-UTRA
Operating Band |
Centre Frequency of Interfering Signal [MHz] |
Interfering Signal mean power [dBm] |
Wanted Signal mean power [dBm] |
Interfering signal centre frequency minimum frequency offset from the channel edge of the wanted signal [MHz] |
Type of Interfering Signal |
||
1-7, 9-11, 13, 14, 18, 19, 21-23, 24, 27, 30, 33-44, 48, 50-52, 54, 65, 66, 68, 70 |
(FUL_low -20) |
to |
(FUL_high +20) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +20) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
8, 26, 28 |
(FUL_low -20) |
to |
(FUL_high +10) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +10) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
12 |
(FUL_low -20) |
to |
(FUL_high +13) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +13) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
17 |
(FUL_low -20) |
to |
(FUL_high +18) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +18) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
20, 71 |
(FUL_low -11) |
to |
(FUL_high +20) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +20) |
to to |
(FUL_low -11) 12750 |
-15 |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
25 |
(FUL_low -20) |
to |
(FUL_high +15) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +15) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
74 |
(FUL_low -20) |
to |
(FUL_high +5) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +5) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
85 |
(FUL_low -20) |
to |
(FUL_high +12) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +12) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
Note 1: PREFSENS depends on the channel bandwidth as specified in Table 7.2.1-3. |
NOTE: Table 7.6.1.1-1b assumes that two operating bands, where the downlink operating band (see Table 5.5-1) of one band would be within the in-band blocking region of the other band, are not deployed in the same geographical area.
Table 7.6.1.1-1c: Blocking performance requirement for Medium Range BS for E-UTRA
Operating Band |
Centre Frequency of Interfering Signal [MHz] |
Interfering Signal mean power [dBm] |
Wanted Signal mean power [dBm] |
Interfering signal centre frequency minimum frequency offset to the lower/higher Base Station RF Bandwidth edge or sub-block edge inside a sub-block gap [MHz] |
Type of Interfering Signal |
||
1-7, 9-11, 13, 14, 18,19, 21-23, 24, 27, 30, 33-45, 48, 50, 52-54, 65, 66, 68, 70 |
(FUL_low -20) |
to |
(FUL_high +20) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +20) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
8, 26, 28 |
(FUL_low -20) |
to |
(FUL_high +10) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +10) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
12 |
(FUL_low -20) |
to |
(FUL_high +13) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +13) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
17 |
(FUL_low -20) |
to |
(FUL_high +18) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +18) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
20, 71 |
(FUL_low -11) |
to |
(FUL_high +20) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +20) |
to to |
(FUL_low -11) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
25 |
(FUL_low -20) |
to |
(FUL_high +15) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +15) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
31, 72, 73, 74, 87, 88 |
(FUL_low -20) |
to |
(FUL_high +5) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +5) |
to to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
46 |
(FUL_low -20) |
to |
(FUL_high +20) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
(FUL_low -500) (FUL_high +20) |
to to |
(FUL_low -20) (FUL_high +500) |
-35 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
1 (FUL_high +500) |
to to |
(FUL_low -500) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
85 |
(FUL_low -20) |
to |
(FUL_high +12) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-2 |
See table 7.6.1.1-2 |
1 (FUL_high +12) |
to |
(FUL_low -20) 12750 |
-15 |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
Note 1: PREFSENS depends on the channel bandwidth as specified in Table 7.2.1-4. Note 2: For a BS capable of multiband operation, in case of interfering signal that is not in the in-band blocking frequency range of the operating band where the wanted signal is present, and not in the in-band blocking frequency range of an adjacent or overlapping operating band, the wanted signal mean power is equal to PREFSENS + 1.4 dB. |
NOTE: Table 7.6.1.1-1c assumes that two operating bands, where the downlink operating band (see Table 5.5-1) of one band would be within the in-band blocking region of the other band, are not deployed in the same geographical area.
Table 7.6.1.1-2: Interfering signals for blocking performance requirement
E-UTRA channel BW of the lowest/highest carrier received [MHz] |
Interfering signal centre frequency minimum offset to the lower/upper Base Station RF Bandwidth edge or sub-block edge inside a sub-block gap [MHz] |
Type of interfering signal |
1.4 |
±2.1 |
1.4 MHz E-UTRA signal |
3 |
±4.5 |
3 MHz E-UTRA signal |
5 |
±7.5 |
5 MHz E-UTRA signal |
10 |
±7.5 |
5 MHz E-UTRA signal |
15 |
±7.5 |
5 MHz E-UTRA signal |
20 |
±7.5 |
5 MHz E-UTRA signal (Note 1) |
20 |
±30 |
20 MHz E-UTRA signal (Note 2) |
Note 1: This type of interfering signal is not applied for Band 46. Note 2: This type of interfering signal is only applied for Band 46. |
For NB-IoT standalone operation, the throughput shall be ≥ 95% of the maximum throughput of the reference measurement channel, with a wanted and an interfering signal coupled to BS antenna input using the parameters in Tables 7.6.1.1-3, 7.6.1.1-3a, 7.6.1.1-3b, 7.6.1.1-3c and 7.6.1.1-4. The reference measurement channel for the wanted signal is identified in Table 7.2.1-5, 7.2.1-5a, 7.2.1-5b and 7.2.1-5c and further specified in Annex A.
The blocking requirement is applicable outside the Base Station RF Bandwidth or Radio Bandwidth. The interfering signal offset is defined relative to the Base Station RF Bandwidth edges or Radio Bandwidth edges.
Table 7.6.1.1-3: Blocking performance requirement for Wide Area BS for NB-IoT standalone operation
Operating Band |
Centre Frequency of Interfering Signal [MHz] |
Interfering Signal mean power [dBm] |
Wanted Signal mean power [dBm] |
Interfering signal centre frequency minimum frequency offset from the lower/upper Base Station RF Bandwidth edge or sub-block edge inside a sub-block gap [MHz] |
Type of Interfering Signal |
||
1-5, 7, 11, 13-14,18,19, 21, 24, 42, 43, 48, 65, 66, 70, 103 |
(FUL_low -20) |
to |
(FUL_high +20) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +20) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
8, 26, 28 |
(FUL_low -20) |
to |
(FUL_high +10) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +10) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
12 |
(FUL_low -20) |
to |
(FUL_high +13) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +13) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
17 |
(FUL_low -20) |
to |
(FUL_high +18) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +18) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
20, 71 |
(FUL_low -11) |
to |
(FUL_high +20) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +20) |
to to |
(FUL_low -11) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
25 |
(FUL_low -20) |
to |
(FUL_high +15) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +15) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
31, 72, 73, 74, 87, 88 |
(FUL_low -20) |
to |
(FUL_high +5) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +5) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
85 |
(FUL_low -20) |
to |
(FUL_high +12) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +12) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
Note 1: PREFSENS is specified in Table 7.2.1-5. Note 2: Up to 24 exceptions are allowed for spurious response frequencies in each wanted signal frequency when measured using a 1MHz step size. For these exceptions the above throughput requirement shall be met when the blocking signal is set to a level of -40 dBm for 15 kHz subcarrier spacing and -46 dBm for 3.75 kHz subcarrier spacing. In addition, each group of exceptions shall not exceed three contiguous measurements using a 1MHz step size. |
Table 7.6.1.1-3a: Blocking performance requirement for Local Area BS for NB-IoT standalone operation
Operating Band |
Centre Frequency of Interfering Signal [MHz] |
Interfering Signal mean power [dBm] |
Wanted Signal mean power [dBm] |
Interfering signal centre frequency minimum frequency offset from the lower/upper Base Station RF Bandwidth edge or sub-block edge inside a sub-block gap [MHz] |
Type of Interfering Signal |
||
1-5, 7, 11, 13-14,18,19, 21, 24, 42, 43, 48, 65, 66, 70, 103 |
(FUL_low -20) |
to |
(FUL_high +20) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +20) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
8, 26, 28 |
(FUL_low -20) |
to |
(FUL_high +10) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +10) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
12 |
(FUL_low -20) |
to |
(FUL_high +13) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +13) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
17 |
(FUL_low -20) |
to |
(FUL_high +18) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +18) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
20, 71 |
(FUL_low -11) |
to |
(FUL_high +20) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +20) |
to to |
(FUL_low -11) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
25 |
(FUL_low -20) |
to |
(FUL_high +15) |
-35 |
PREFSENS +6dB (Note 2) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +15) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 2) |
⎯ |
CW carrier |
|
31, 72, 74, 87, 88 |
(FUL_low -20) |
to |
(FUL_high +5) |
-35 |
PREFSENS +6dB (Note 2) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +5) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 2) |
⎯ |
CW carrier |
|
85 |
(FUL_low -20) |
to |
(FUL_high +12) |
-35 |
PREFSENS +6dB (Note 2) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +12) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 2) |
⎯ |
CW carrier |
|
Note 1: PREFSENS is specified in Table 7.2.1-5a. Note 2: Up to 24 exceptions are allowed for spurious response frequencies in each wanted signal frequency when measured using a 1MHz step size. For these exceptions the above throughput requirement shall be met when the blocking signal is set to a level of -40 dBm for 15 kHz subcarrier spacing and -46 dBm for 3.75 kHz subcarrier spacing. In addition, each group of exceptions shall not exceed three contiguous measurements using a 1MHz step size. |
Table 7.6.1.1-3b: Blocking performance requirement for Home BS for NB-IoT standalone operation
Operating Band |
Centre Frequency of Interfering Signal [MHz] |
Interfering Signal mean power [dBm] |
Wanted Signal mean power [dBm] |
Interfering signal centre frequency minimum frequency offset from the lower/upper Base Station RF Bandwidth edge or sub-block edge inside a sub-block gap [MHz] |
Type of Interfering Signal |
||
1-5, 7,11, 13-14,18,19, 21, 24, 42, 43, 48, 65, 66, 70, 103 |
(FUL_low -20) |
to |
(FUL_high +20) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +20) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
8, 26, 28 |
(FUL_low -20) |
to |
(FUL_high +10) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +10) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
12 |
(FUL_low -20) |
to |
(FUL_high +13) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +13) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
17 |
(FUL_low -20) |
to |
(FUL_high +18) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +18) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
20, 71 |
(FUL_low -11) |
to |
(FUL_high +20) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +20) |
to to |
(FUL_low -11) 12750 |
-15 (Note 2) |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
25 |
(FUL_low -20) |
to |
(FUL_high +15) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +15) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
74 |
(FUL_low -20) |
to |
(FUL_high +5) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +5) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
85 |
(FUL_low -20) |
to |
(FUL_high +12) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +12) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
Note 1: PREFSENS is specified in Table 7.2.1-5b. Note 2: Up to 24 exceptions are allowed for spurious response frequencies in each wanted signal frequency when measured using a 1MHz step size. For these exceptions the above throughput requirement shall be met when the blocking signal is set to a level of -40 dBm for 15 kHz subcarrier spacing and -46 dBm for 3.75 kHz subcarrier spacing. In addition, each group of exceptions shall not exceed three contiguous measurements using a 1MHz step size. |
Table 7.6.1.1-3c: Blocking performance requirement for Medium Range BS for NB-IoT standalone operation
Operating Band |
Centre Frequency of Interfering Signal [MHz] |
Interfering Signal mean power [dBm] |
Wanted Signal mean power [dBm] |
Interfering signal centre frequency minimum frequency offset from the lower/upper Base Station RF Bandwidth edge or sub-block edge inside a sub-block gap [MHz] |
Type of Interfering Signal |
||
1-5, 7, 11, 13-14,18,19, 21, 24, 42, 43, 48, 65, 66, 70, 103 |
(FUL_low -20) |
to |
(FUL_high +20) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +20) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
8, 26, 28 |
(FUL_low -20) |
to |
(FUL_high +10) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +10) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
12 |
(FUL_low -20) |
to |
(FUL_high +13) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +13) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
17 |
(FUL_low -20) |
to |
(FUL_high +18) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +18) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
20, 71 |
(FUL_low -11) |
to |
(FUL_high +20) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +20) |
to to |
(FUL_low -11) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
25 |
(FUL_low -20) |
to |
(FUL_high +15) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +15) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
31, 72, 74, 87, 88 |
(FUL_low -20) |
to |
(FUL_high +5) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +5) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
85 |
(FUL_low -20) |
to |
(FUL_high +12) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-4 |
See table 7.6.1.1-4 |
1 (FUL_high +12) |
to to |
(FUL_low -20) 12750 |
-15 (Note 2) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
Note 1: PREFSENS is specified in Table 7.2.1-5c. Note 2: Up to 24 exceptions are allowed for spurious response frequencies in each wanted signal frequency when measured using a 1MHz step size. For these exceptions the above throughput requirement shall be met when the blocking signal is set to a level of -40 dBm for 15 kHz subcarrier spacing and -46 dBm for 3.75 kHz subcarrier spacing. In addition, each group of exceptions shall not exceed three contiguous measurements using a 1MHz step size. |
NOTE: Tables 7.6.1.1-3, 7.6.1.1-3a, 7.6.1.1-3b and 7.6.1.1-3c assumes that two operating bands, where the downlink operating band (see Table 5.5-1) of one band would be within the in-band blocking region of the other band, are not deployed in the same geographical area.
Table 7.6.1.1-4: Interfering signals for blocking performance requirement for NB-IoT standalone operation
NB-IoT channel BW of the lowest/highest carrier received [MHz] |
Interfering signal centre frequency minimum offset to the lower/upper Base Station RF Bandwidth edge or sub-block edge inside a sub-block gap [MHz] |
Type of interfering signal |
0.2 |
±7.5 |
5MHz E-UTRA signal |
For E-UTRA with NB-IoT in-band/guard band operation, the throughput shall be ≥ 95% of the maximum throughput of the reference measurement channel, with a wanted and an interfering signal coupled to BS antenna input using the parameters in Tables 7.6.1.1-5, 7.6.1.1-5a, 7.6.1.1-5b, 7.6.1.1-5c and 7.6.1.1-6. The reference measurement channel for the wanted signal is identified in Table 7.2.1-1, 7.2.1-2, 7.2.1-3 and 7.2.1-4 for each channel bandwidth for E-UTRA, Table 7.2.1-5, 7.2.1-5a, 7.2.1-5b and 7.2.1-5c for NB-IoT and further specified in Annex A.
The blocking requirement is applicable outside the Base Station RF Bandwidth or Radio Bandwidth. The interfering signal offset is defined relative to the Base Station RF Bandwidth edges or Radio Bandwidth edges.
Table 7.6.1.1-5: Blocking performance requirement for Wide Area BS for E-UTRA with NB-IoT in-band/guard band operation
Operating Band |
Centre Frequency of Interfering Signal [MHz] |
Interfering Signal mean power [dBm] |
Wanted Signal mean power [dBm] |
Interfering signal centre frequency minimum frequency offset from the lower/upper Base Station RF Bandwidth edge or sub-block edge inside a sub-block gap [MHz] |
Type of Interfering Signal |
||
1-5, 7,11, 13-14,18,19, 21, 24, 42, 43, 48, 65, 66, 70 |
(FUL_low -20) |
to |
(FUL_high +20) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +20) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
8, 26, 28 |
(FUL_low -20) |
to |
(FUL_high +10) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +10) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
12 |
(FUL_low -20) |
to |
(FUL_high +13) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +13) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
17 |
(FUL_low -20) |
to |
(FUL_high +18) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +18) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
20, 71 |
(FUL_low -11) |
to |
(FUL_high +20) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +20) |
to to |
(FUL_low -11) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
25 |
(FUL_low -20) |
to |
(FUL_high +15) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +15) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
31, 72, 73, 74, 87, 88 |
(FUL_low -20) |
to |
(FUL_high +5) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +5) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
85 |
(FUL_low -20) |
to |
(FUL_high +12) |
-43 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +12) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
Note 1: PREFSENS depends on the channel bandwidth as specified in Table 7.2.1-1 for E-UTRA and is specified in Table 7.2.1-5 for NB-IoT. Note 2: For a BS capable of multiband operation, in case of interfering signal that is not in the in-band blocking frequency range of the operating band where the wanted signal is present, and not in the in-band blocking frequency range of an adjacent or overlapping operating band, the wanted signal mean power is equal to PREFSENS + 1.4 dB. Note 3: For NB-IoT, up to 24 exceptions are allowed for spurious response frequencies in each wanted signal frequency when measured using a 1MHz step size. For these exceptions the above throughput requirement shall be met when the blocking signal is set to a level of -40 dBm for 15 kHz subcarrier spacing and -46 dBm for 3.75 kHz subcarrier spacing. In addition, each group of exceptions shall not exceed three contiguous measurements using a 1MHz step size. |
Table 7.6.1.1-5a: Blocking performance requirement for Local Area BS for E-UTRA with NB-IoT in-band/guard band operation
Operating Band |
Centre Frequency of Interfering Signal [MHz] |
Interfering Signal mean power [dBm] |
Wanted Signal mean power [dBm] |
Interfering signal centre frequency minimum frequency offset from the lower/upper Base Station RF Bandwidth edge or sub-block edge inside a sub-block gap [MHz] |
Type of Interfering Signal |
||
1-5, 7, 11, 13-14,18,19, 21, 24, 42, 43, 48, 65, 66, 70 |
(FUL_low -20) |
to |
(FUL_high +20) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +20) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
8, 26, 28 |
(FUL_low -20) |
to |
(FUL_high +10) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +10) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
12 |
(FUL_low -20) |
to |
(FUL_high +13) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +13) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
17 |
(FUL_low -20) |
to |
(FUL_high +18) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +18) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
20, 71 |
(FUL_low -11) |
to |
(FUL_high +20) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +20) |
to to |
(FUL_low -11) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
25 |
(FUL_low -20) |
to |
(FUL_high +15) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +15) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
31, 72, 74, 87, 88 |
(FUL_low -20) |
to |
(FUL_high +5) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +5) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
85 |
(FUL_low -20) |
to |
(FUL_high +12) |
-35 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +12) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
Note 1: PREFSENS depends on the channel bandwidth as specified in Table 7.2.1-1 for E-UTRA and is specified in Table 7.2.1-5a for NB-IoT. Note 2: For a BS capable of multiband operation, in case of interfering signal that is not in the in-band blocking frequency range of the operating band where the wanted signal is present, and not in the in-band blocking frequency range of an adjacent or overlapping operating band, the wanted signal mean power is equal to PREFSENS + 1.4 dB. Note 3: For NB-IoT, up to 24 exceptions are allowed for spurious response frequencies in each wanted signal frequency when measured using a 1MHz step size. For these exceptions the above throughput requirement shall be met when the blocking signal is set to a level of -40 dBm for 15 kHz subcarrier spacing and -46 dBm for 3.75 kHz subcarrier spacing. In addition, each group of exceptions shall not exceed three contiguous measurements using a 1MHz step size. |
Table 7.6.1.1-5b: Blocking performance requirement for Home BS for E-UTRA with NB-IoT in-band/guard band operation
Operating Band |
Centre Frequency of Interfering Signal [MHz] |
Interfering Signal mean power [dBm] |
Wanted Signal mean power [dBm] |
Interfering signal centre frequency minimum frequency offset from the lower/upper Base Station RF Bandwidth edge or sub-block edge inside a sub-block gap [MHz] |
Type of Interfering Signal |
||
1-5, 7, 11, 13-14,18,19, 21, 24, 42, 43, 48, 65, 66, 70 |
(FUL_low -20) |
to |
(FUL_high +20) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +20) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
8, 26, 28 |
(FUL_low -20) |
to |
(FUL_high +10) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +10) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
12 |
(FUL_low -20) |
to |
(FUL_high +13) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +13) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
17 |
(FUL_low -20) |
to |
(FUL_high +18) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +18) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
20, 71 |
(FUL_low -11) |
to |
(FUL_high +20) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +20) |
to to |
(FUL_low -11) 12750 |
-15 (Note 3) |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
25 |
(FUL_low -20) |
to |
(FUL_high +15) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +15) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
74 |
(FUL_low -20) |
to |
(FUL_high +5) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +5) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
85 |
(FUL_low -20) |
to |
(FUL_high +12) |
-27 |
PREFSENS +14dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +12) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +14dB (Note 1) |
⎯ |
CW carrier |
|
Note 1: PREFSENS depends on the channel bandwidth as specified in Table 7.2.1-1 for E-UTRA and is specified in Table 7.2.1-5b for NB-IoT. Note 2: (Void) Note 3: For NB-IoT, up to 24 exceptions are allowed for spurious response frequencies in each wanted signal frequency when measured using a 1MHz step size. For these exceptions the above throughput requirement shall be met when the blocking signal is set to a level of -40 dBm for 15 kHz subcarrier spacing and -46 dBm for 3.75 kHz subcarrier spacing. In addition, each group of exceptions shall not exceed three contiguous measurements using a 1MHz step size. |
Table 7.6.1.1-5c: Blocking performance requirement for Medium Range BS for E-UTRA with NB-IoT in-band/guard band operation
Operating Band |
Centre Frequency of Interfering Signal [MHz] |
Interfering Signal mean power [dBm] |
Wanted Signal mean power [dBm] |
Interfering signal centre frequency minimum frequency offset from the lower/upper Base Station RF Bandwidth edge or sub-block edge inside a sub-block gap [MHz] |
Type of Interfering Signal |
||
1-5, 7, 11, 13-14,18,19, 21, 24, 42, 43, 48, 65, 66, 70 |
(FUL_low -20) |
to |
(FUL_high +20) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +20) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
8, 26, 28 |
(FUL_low -20) |
to |
(FUL_high +10) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +10) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
12 |
(FUL_low -20) |
to |
(FUL_high +13) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +13) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
17 |
(FUL_low -20) |
to |
(FUL_high +18) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +18) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
20, 71 |
(FUL_low -11) |
to |
(FUL_high +20) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +20) |
to to |
(FUL_low -11) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
25 |
(FUL_low -20) |
to |
(FUL_high +15) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +15) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
31, 72, 74, 87, 88 |
(FUL_low -20) |
to |
(FUL_high +5) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +5) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
85 |
(FUL_low -20) |
to |
(FUL_high +12) |
-38 |
PREFSENS +6dB (Note 1) |
See table 7.6.1.1-6 |
See table 7.6.1.1-6 |
1 (FUL_high +12) |
to to |
(FUL_low -20) 12750 |
-15 (Note 3) |
PREFSENS +6dB (Note 1) |
⎯ |
CW carrier |
|
Note 1: PREFSENS depends on the channel bandwidth as specified in Table 7.2.1-1 for E-UTRA and is specified in Table 7.2.1-5c for NB-IoT. Note 2: For a BS capable of multiband operation, in case of interfering signal that is not in the in-band blocking frequency range of the operating band where the wanted signal is present, and not in the in-band blocking frequency range of an adjacent or overlapping operating band, the wanted signal mean power is equal to PREFSENS + 1.4 dB. Note 3: For NB-IoT, up to 24 exceptions are allowed for spurious response frequencies in each wanted signal frequency when measured using a 1MHz step size. For these exceptions the above throughput requirement shall be met when the blocking signal is set to a level of -40 dBm for 15 kHz subcarrier spacing and -46 dBm for 3.75 kHz subcarrier spacing. In addition, each group of exceptions shall not exceed three contiguous measurements using a 1MHz step size.. |
NOTE: Tables 7.6.1.1-5, 7.6.1.1-5a and 7.6.1.1-5b assume that two operating bands, where the downlink operating band (see Table 5.5-1) of one band would be within the in-band blocking region of the other band, are not deployed in the same geographical area.
Table 7.6.1.1-6: Interfering signals for blocking performance requirement for E-UTRA with NB-IoT in-band/guard band operation
E-UTRA channel BW of the lowest/highest carrier received [MHz] |
Interfering signal centre frequency minimum offset to the lower/upper Base Station RF Bandwidth edge or sub-block edge inside a sub-block gap [MHz] |
Type of interfering signal |
3(Note) |
±4.5 |
3MHz E-UTRA signal |
5 |
±7.5 |
5MHz E-UTRA signal |
10 |
±7.5 |
5MHz E-UTRA signal |
15 |
±7.5 |
5MHz E-UTRA signal |
20 |
±7.5 |
5MHz E-UTRA signal |
Note: 3 MHz channel bandwidth is not applicable to guard band operation. |
7.6.2 Co-location with other base stations
This additional blocking requirement may be applied for the protection of E-UTRA and NB-IoT BS receivers when GSM, CDMA, UTRA, E-UTRA, NR or NB-IoT BS operating in a different frequency band are co-located with an E-UTRA or NB-IoT BS. The requirement is applicable to all channel bandwidths supported by the E-UTRA BS and E-UTRA with NB-IoT in-band/guard band operation.
The requirements in this clause assume a 30 dB coupling loss between interfering transmitter and E-UTRA or NB-IoT BS receiver and are based on co-location with base stations of the same class.
7.6.2.1 Minimum requirement
The throughput shall be ≥ 95% of the maximum throughput of the reference measurement channel, with a wanted and an interfering signal coupled to BS antenna input using the parameters in Table 7.6.2.1-1 for Wide Area BS, in Table 7.6.2.1-2 for Local Area BS and in Table 7.6.2.1-3 for Medium Range BS. The reference measurement channel for the wanted signal is identified in Tables 7.2.1-1, 7.2.1-2 and 7.2.1-4 for each channel bandwidth for E-UTRA, Table 7.2.1-5 for NB-IoT and further specified in Annex A.
Table 7.6.2.1-1: Blocking performance requirement for E-UTRA and NB-IoT Wide Area BS when co-located with BS in other frequency bands.
Co-located BS type |
Centre Frequency of Interfering Signal (MHz) |
Interfering Signal mean power (dBm) |
Wanted Signal mean power (dBm) |
Type of Interfering Signal |
Macro GSM850 or CDMA850 |
869 – 894 |
+16** |
PREFSENS + 6dB* |
CW carrier |
Macro GSM900 |
921 – 960 |
+16** |
PREFSENS + 6dB* |
CW carrier |
Macro DCS1800 |
1805 – 1880 |
+16** |
PREFSENS + 6dB* |
CW carrier |
Macro PCS1900 |
1930 – 1990 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band I or E-UTRA Band 1 or NR band n1 |
2110 – 2170 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band II or E-UTRA Band 2 or NR band n2 |
1930 – 1990 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band III or E-UTRA Band 3 or NR band n3 |
1805 – 1880 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band IV or E-UTRA Band 4 |
2110 – 2155 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band V or E-UTRA Band 5 or NR band n5 |
869 – 894 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band VI or E-UTRA Band 6 |
875 – 885 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band VII or E-UTRA Band 7 or NR band n7 |
2620 – 2690 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band VIII or E-UTRA Band 8 or NR band n8 |
925 – 960 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band IX or E-UTRA Band 9 |
1844.9 – 1879.9 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band X or E-UTRA Band 10 |
2110 – 2170 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band XI or E-UTRA Band 11 |
1475.9 –1495.9 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band XII or E-UTRA Band 12 or NR band n12 |
729 – 746 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band XIIII or E-UTRA Band 13 or NR Band n13 |
746 – 756 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band XIV or E-UTRA Band 14 or NR Band n14 |
758 – 768 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 17 |
734 – 746 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 18 |
860 – 875 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band XIX or E-UTRA Band 19 |
875 – 890 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band XX or E-UTRA Band 20 or NR band n20 |
791 – 821 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band XXI or E-UTRA Band 21 |
1495.9 – 1510.9 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band XXII or E-UTRA Band 22 |
3510 – 3590 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 24 or NR Band n24 |
1525 – 1559 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band XXV or E-UTRA Band 25 or NR band n25 |
1930 – 1995 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band XXVI or E-UTRA Band 26 or NR Band n26 |
859 – 894 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 27 |
852 – 869 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 28 or NR band n28 |
758 – 803 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 29 or NR Band n29 |
717-728 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 30 or NR Band n30 |
2350 – 2360 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 31 |
462.5-467.5 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA FDD Band XXXII or E-UTRA Band 32 |
1452-1496 (NOTE 3) |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA TDD Band a) or E-UTRA Band 33 |
1900-1920 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA TDD Band a) or E-UTRA Band 34 or NR band n34 |
2010-2025 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA TDD Band b) or E-UTRA Band 35 |
1850-1910 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA TDD Band b) or E-UTRA Band 36 |
1930-1990 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA TDD Band c) or E-UTRA Band 37 |
1910-1930 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA TDD Band d) or E-UTRA Band 38 or NR band n38 |
2570-2620 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA TDD Band f) or E-UTRA Band 39 or NR band n39 |
1880-1920 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA UTRA TDD Band e) or E-UTRA Band 40 or NR band n40 |
2300-2400 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 41 or NR band n41 |
2496 – 2690 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 42 |
3400-3600 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 43 |
3600-3800 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 44 |
703-803 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 45 |
1447-1467 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 48 or NR Band n48 |
3550-3700 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 50 or NR band n50 |
1432 – 1517 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 52 |
3300-3400 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 54 |
1670 – 1675 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 65 or NR Band n65 |
2110 – 2200 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 66 or NR band n66 |
2110 – 2200 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 67 or NR band n67 |
738-758 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 68 |
753-783 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 69 |
2570-2620 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 70 or NR band n70 |
1995 – 2020 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 71 or NR band n71 |
617 – 652 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 72 |
461 – 466 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 73 |
460 – 465 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 74 or NR band n74 |
1475 – 1518 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 75 |
1432 – 1517 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA NR band n77 |
3300-4200 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA NR band n78 |
3300-3800 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA NR band n79 |
4400-5000 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 85 or NR band n85 |
728 – 746 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 87 |
420 – 425 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 88 |
422 – 427 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA NR band n92 |
1432 – 1517 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA NR band n94 |
1432 – 1517 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA NR band n100 |
919.4 – 925 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA NR band n101 |
1900 – 1910 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA E-UTRA Band 103 |
757 – 758 |
+16** |
PREFSENS + 6dB* |
CW carrier |
WA NR band n104 |
6425 – 7125 |
+16 |
PREFSENS + 6dB* |
CW carrier |
Note*: PREFSENS depends on the channel bandwidth as specified in Table 7.2.1-1 for E-UTRA and is specified in Table 7.2.1-5 for NB-IoT. Note**: For NB-IoT, up to 24 exceptions are allowed for spurious response frequencies in each wanted signal frequency when measured using a 1MHz step size. For these exceptions the above throughput requirement shall be met when the blocking signal is set to a level of -40 dBm for 15 kHz subcarrier spacing and -46 dBm for 3.75 kHz subcarrier spacing. In addition, each group of exceptions shall not exceed three contiguous measurements using a 1MHz step size. |
||||
NOTE 1: Except for a BS operating in Band 13, these requirements do not apply when the interfering signal falls within any of the supported uplink operating band or in the 10 MHz immediately outside any of the supported uplink operating band. NOTE 2: Some combinations of bands may not be possible to co-site based on the requirements above. The current state-of-the-art technology does not allow a single generic solution for co-location of UTRA TDD or E-UTRA TDD with E-UTRA FDD on adjacent frequencies for 30dB BS-BS minimum coupling loss. However, there are certain site-engineering solutions that can be used. These techniques are addressed in TR 25.942 [8]. NOTE 3: For a BS operating in band 11, 21 or 74, the requirement for co-location with Band 32 applies for interfering signal within the frequency range 1475.9-1495.9 MHz. NOTE 4: Co-located TDD base stations that are synchronized and using the same or adjacent operating band can receive without special co-location requirements. For unsynchronized base stations, special co-location requirements may apply that are not covered by the 3GPP specifications. |
Table 7.6.2.1-2: Blocking performance requirement for E-UTRA and NB-IoT Local Area BS when co-located with BS in other frequency bands.
Co-located BS type |
Centre Frequency of Interfering Signal (MHz) |
Interfering Signal mean power (dBm) |
Wanted Signal mean power (dBm) |
Type of Interfering Signal |
Pico GSM850 |
869 – 894 |
-7** |
PREFSENS + 6dB* |
CW carrier |
Pico GSM900 |
921 – 960 |
-7** |
PREFSENS + 6dB* |
CW carrier |
Pico DCS1800 |
1805 – 1880 |
-4** |
PREFSENS + 6dB* |
CW carrier |
Pico PCS1900 |
1930 – 1990 |
-4** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band I or E-UTRA Band 1 or NR band n1 |
2110 – 2170 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band II or E-UTRA Band 2 or NR band n2 |
1930 – 1990 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band III or E-UTRA Band 3 or NR band n3 |
1805 – 1880 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band IV or E-UTRA Band 4 |
2110 – 2155 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band V or E-UTRA Band 5 or NR band n5 |
869 – 894 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band VI or E-UTRA Band 6 |
875 – 885 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band VII or E-UTRA Band 7 or NR band n7 |
2620 – 2690 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band VIII or E-UTRA Band 8 or NR band n8 |
925 – 960 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band IX or E-UTRA Band 9 |
1844.9 – 1879.9 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band X or E-UTRA Band 10 |
2110 – 2170 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band XI or E-UTRA Band 11 |
1475.9 – 1495.9 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band XII or E-UTRA Band 12 or NR band n12 |
729 – 746 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band XIIII or E-UTRA Band 13 or NR Band n13 |
746 – 756 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band XIV or E-UTRA Band 14 or NR Band n14 |
758 – 768 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 17 |
734 – 746 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 18 |
860 – 875 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band XIX or E-UTRA Band 19 |
875 – 890 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band XX or E-UTRA Band 20 or NR band n20 |
791 – 821 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band XXI or E-UTRA Band 21 |
1495.9 – 1510.9 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band XXII or E-UTRA Band 22 |
3510 – 3590 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 24 or NR Band n24 |
1525 – 1559 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band XXV or E-UTRA Band 25 or NR band n25 |
1930 – 1995 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band XXVI or E-UTRA Band 26 or NR Band n26 |
859 – 894 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 27 |
852 – 869 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 28 or NR band n28 |
758 – 803 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 29 or NR Band n29 |
717 – 728 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 30 or NR Band n30 |
2350 – 2360 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 31 |
462.5 – 467.5 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA FDD Band XXXII or E-UTRA Band 32 |
1452 – 1496 (NOTE 3) |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA TDD Band a) or E-UTRA Band 33 |
1900 – 1920 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA TDD Band a) or E-UTRA Band 34 or NR band n34 |
2010 – 2025 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA TDD Band b) or E-UTRA Band 35 |
1850 – 1910 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA TDD Band b) or E-UTRA Band 36 |
1930 – 1990 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA TDD Band c) or E-UTRA Band 37 |
1910 – 1930 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA TDD Band d) or E-UTRA Band 38 or NR band n38 |
2570 – 2620 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA UTRA TDD Band f) or E-UTRA Band 39 or NR band n39 |
1880 – 1920 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA UTRA TDD Band e) or Band 40 or NR band n40 |
2300 – 2400 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 41 or NR band n41 |
2496 – 2690 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 42 |
3400 – 3600 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 43 |
3600 – 3800 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 44 |
703 – 803 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 45 |
1447 – 1467 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 46 or NR Band n46 |
5150 – 5925 |
-6 |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 48 or NR Band n48 |
3550 – 3700 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 49 |
3550 – 3700 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 50 or NR band n50 |
1432 – 1517 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 51 or NR band n51 |
1427 – 1432 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 52 |
3300 – 3400 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 53 or NR Band n53 |
2483.5 – 2495 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 54 |
1670 – 1675 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 65 or NR Band n65 |
2110 – 2200 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 66 or NR band n66 |
2110 – 2200 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 67 or NR band n67 |
738 – 758 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 68 |
753 – 783 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 69 |
2570 – 2620 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 70 or NR band n70 |
1995 – 2020 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 71 or NR band n71 |
617 – 652 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 72 |
461 – 466 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 73 |
460 – 465 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 74 or NR band n74 |
1475 – 1518 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 75 or NR band n75 |
1432 – 1517 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 76 or NR band n76 |
1427 – 1432 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA NR band n77 |
3300 – 4200 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA NR band n78 |
3300 – 3800 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA NR band n79 |
4400 – 5000 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 85 or NR band n85 |
728 – 746 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 87 |
420 – 425 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 88 |
422 – 427 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA NR band n91 |
1427 – 1432 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA NR band n92 |
1432 – 1517 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA NR band n93 |
1427 – 1432 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA NR band n94 |
1432 – 1517 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA NR band n96 |
5925 – 7125 |
-6 |
PREFSENS + 6dB* |
CW carrier |
LA NR band n102 |
5925 – 6425 |
-6 |
PREFSENS + 6dB* |
CW carrier |
LA E-UTRA Band 103 |
757 – 758 |
-6** |
PREFSENS + 6dB* |
CW carrier |
LA NR band n104 |
6425 – 7125 |
-6 |
PREFSENS + 6dB* |
CW carrier |
Note*: PREFSENS depends on the channel bandwidth as specified in Table 7.2.1-2. Note**: For NB-IoT, up to 24 exceptions are allowed for spurious response frequencies in each wanted signal frequency when measured using a 1MHz step size. For these exceptions the above throughput requirement shall be met when the blocking signal is set to a level of -40 dBm for 15 kHz subcarrier spacing and -46 dBm for 3.75 kHz subcarrier spacing. In addition, each group of exceptions shall not exceed three contiguous measurements using a 1MHz step size. |
||||
NOTE 1: Except for a BS operating in Band 13, these requirements do not apply when the interfering signal falls within any of the supported uplink operating band or in the 10 MHz immediately outside any of the supported uplink operating band. NOTE 2: Some combinations of bands may not be possible to co-site based on the requirements above. The current state-of-the-art technology does not allow a single generic solution for co-location of UTRA TDD or E-UTRA TDD with E-UTRA FDD on adjacent frequencies for 30dB BS-BS minimum coupling loss. However, there are certain site-engineering solutions that can be used. These techniques are addressed in TR 25.942 [8]. NOTE 3: For a BS operating in band 11, 21 or 74, the requirement for co-location with Band 32 applies for interfering signal within the frequency range 1475.9-1495.9 MHz. NOTE 4: Co-located TDD base stations that are synchronized and using the same or adjacent operating band can receive without special co-location requirements. For unsynchronized base stations (except in Band 46), special co-location requirements may apply that are not covered by the 3GPP specifications. |
Table 7.6.2.1-3: Blocking performance requirement for E-UTRA and NB-IoT Medium Range BS when co-located with BS in other frequency bands.
Co-located BS type |
Centre Frequency of Interfering Signal (MHz) |
Interfering Signal mean power (dBm) |
Wanted Signal mean power (dBm) |
Type of Interfering Signal |
Micro/MR GSM850 |
869 – 894 |
+8** |
PREFSENS + 6dB* |
CW carrier |
Micro/MR GSM900 |
921 – 960 |
+8** |
PREFSENS + 6dB* |
CW carrier |
Micro/MR DCS1800 |
1805 – 1880 |
+8** |
PREFSENS + 6dB* |
CW carrier |
Micro/MR PCS1900 |
1930 – 1990 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band I or E-UTRA Band 1 or NR band n1 |
2110 – 2170 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band II or E-UTRA Band 2 or NR band n2 |
1930 – 1990 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band III or E-UTRA Band 3 or NR band n3 |
1805 – 1880 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band IV or E-UTRA Band 4 |
2110 – 2155 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band V or E-UTRA Band 5 or NR band n5 |
869 – 894 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band VI or E-UTRA Band 6 |
875 – 885 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band VII or E-UTRA Band 7 or NR band n7 |
2620 – 2690 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band VIII or E-UTRA Band 8 or NR band n8 |
925 – 960 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band IX or E-UTRA Band 9 |
1844.9 – 1879.9 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band X or E-UTRA Band 10 |
2110 – 2170 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band XI or E-UTRA Band 11 |
1475.9 –1495.9 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band XII or E-UTRA Band 12 or NR band n12 |
729 – 746 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band XIIII or E-UTRA Band 13 or NR Band n13 |
746 – 756 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band XIV or E-UTRA Band 14 or NR Band n14 |
758 – 768 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 17 |
734 – 746 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 18 |
860 – 875 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band XIX or E-UTRA Band 19 |
875 – 890 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band XX or E-UTRA Band 20 or NR band n20 |
791 – 821 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band XXI or E-UTRA Band 21 |
1495.9 – 1510.9 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band XXII or E-UTRA Band 22 |
3510 – 3590 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 24 or NR Band n24 |
1525 – 1559 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band XXV or E-UTRA Band 25 or NR band n25 |
1930 – 1995 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band XXVI or E-UTRA Band 26 or NR Band n26 |
859 – 894 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 27 |
852 – 869 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 28 or NR band n28 |
758 – 803 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 29 or NR Band n29 |
717 – 728 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 30 or NR Band n30 |
2350 – 2360 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 31 |
462.5 – 467.5 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR UTRA FDD Band XXXII or E-UTRA Band 32 |
1452-1496 (NOTE 3) |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 33 |
1900 – 1920 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 34 or NR band n34 |
2010 – 2025 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 35 |
1850 – 1910 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 36 |
1930 – 1990 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 37 |
1910 – 1930 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 38 or NR band n38 |
2570 – 2620 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 39 or NR band n39 |
1880 – 1920 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 40 or NR band n40 |
2300 – 2400 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 41 or NR band n41 |
2496 – 2690 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 42 |
3400 – 3600 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 43 |
3600 – 3800 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 44 |
703 – 803 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 45 |
1447 – 1467 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 46 or NR Band n46 |
5150 – 5925 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 48 or NR Band n48 |
3550-3700 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 50 or NR band n50 |
1432 – 1517 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 52 |
3300 – 3400 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 53 or NR Band n53 |
2483.5 – 2495 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 54 |
1670 – 1675 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 65 or NR Band n65 |
2110 – 2200 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 66 or NR band n66 |
2110 – 2200 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 67 or NR band n67 |
738-758 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 68 |
753-783 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 69 |
2570-2620 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 70 or NR band n70 |
1995 – 2020 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 71 or NR band n71 |
617 – 652 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 72 |
461 – 466 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 73 |
460 – 465 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 74 or NR band n74 |
1475 – 1518 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 75 or NR band n75 |
1432 – 1517 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR NR band n77 |
3300-4200 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR NR band n78 |
3300-3800 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR NR band n79 |
4400-5000 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 85 or NR band n85 |
728 – 746 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 87 |
420 – 425 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 88 |
422 – 427 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR NR band n92 |
1432 – 1517 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR NR band n94 |
1432 – 1517 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR NR band n96 |
5925 – 7125 |
+8 |
PREFSENS + 6dB* |
CW carrier |
MR NR band n102 |
5925 – 6425 |
+8 |
PREFSENS + 6dB* |
CW carrier |
MR E-UTRA Band 103 |
757 – 758 |
+8** |
PREFSENS + 6dB* |
CW carrier |
MR NR band n104 |
6425 – 7125 |
+8 |
PREFSENS + 6dB* |
CW carrier |
Note*: PREFSENS depends on the channel bandwidth as specified in Table 7.2.1-4. Note**: For NB-IoT, up to 24 exceptions are allowed for spurious response frequencies in each wanted signal frequency when measured using a 1MHz step size. For these exceptions the above throughput requirement shall be met when the blocking signal is set to a level of -40 dBm for 15 kHz subcarrier spacing and -46 dBm for 3.75 kHz subcarrier spacing. In addition, each group of exceptions shall not exceed three contiguous measurements using a 1MHz step size. |
||||
NOTE 1: Except for a BS operating in Band 13, these requirements do not apply when the interfering signal falls within any of the supported uplink operating band or in the 10 MHz immediately outside any of the supported uplink operating band. NOTE 2: Some combinations of bands may not be possible to co-site based on the requirements above. The current state-of-the-art technology does not allow a single generic solution for co-location of UTRA TDD or E-UTRA TDD with E-UTRA FDD on adjacent frequencies for 30dB BS-BS minimum coupling loss. However, there are certain site-engineering solutions that can be used. These techniques are addressed in TR 25.942 [8]. NOTE 3: For a BS operating in band 11, 21 or 74, the requirement for co-location with Band 32 applies for interfering signal within the frequency range 1475.9-1495.9 MHz. NOTE 4: Co-located TDD base stations that are synchronized and using the same or adjacent operating band can receive without special co-location requirements. For unsynchronized base stations (except in Band 46), special co-location requirements may apply that are not covered by the 3GPP specifications. |
7.6.3 Additional requirement (regional)
For the Public Safety LTE BS in Korea from 718 to 728 MHz in band 28, the wanted and the interfering signal coupled to the BS antenna input are specified in Tables G-2.2, G-2.3, G-2.4 and G-2.5 for the blocking requirements. The reference measurement channel for the wanted signal is A.1-3 for 10 MHz channel bandwidth and further specified in Annex A.