7.4 In-channel selectivity
36.1043GPPBase Station (BS) radio transmission and receptionEvolved Universal Terrestrial Radio Access (E-UTRA)Release 18TS
In-channel selectivity (ICS) is a measure of the receiver ability to receive a wanted signal at its assigned resource block locations in the presence of an interfering signal received at a larger power spectral density. In this condition a throughput requirement shall be met for a specified reference measurement channel. The interfering signal shall be an E-UTRA signal as specified in Annex C and shall be time aligned with the wanted signal.
7.4.1 Minimum requirement
For E-UTRA, the throughput shall be ≥ 95% of the maximum throughput of the reference measurement channel as specified in Annex A with parameters specified in Table 7.4.1-1 for Wide Area BS, in Table 7.4.1-2 for Local Area BS, in Table 7.4.1-3 for Home BS and in Table 7.4.1-4 for Medium Range BS.
Table 7.4.1-1 Wide Area BS in-channel selectivity for E-UTRA
|
E-UTRA channel bandwidth (MHz) |
Reference measurement channel |
Wanted signal mean power [dBm] |
Interfering signal mean power [dBm] |
Type of interfering signal |
|
1.4 |
A1-4 in Annex A.1 |
-106.9 |
-87 |
1.4 MHz E-UTRA signal, 3 RBs |
|
3 |
A1-5 in Annex A.1 |
-102.1 |
-84 |
3 MHz E-UTRA signal, 6 RBs |
|
5 |
A1-2 in Annex A.1 |
-100.0 |
-81 |
5 MHz E-UTRA signal, 10 RBs |
|
10 |
A1-3 in Annex A.1 |
-98.5 |
-77 |
10 MHz E-UTRA signal, 25 RBs |
|
15 |
A1-3 in Annex A.1 (Note) |
-98.5 |
-77 |
15 MHz E-UTRA signal, 25 RBs (Note) |
|
20 |
A1-3 in Annex A.1 (Note) |
-98.5 |
-77 |
20 MHz E-UTRA signal, 25 RBs (Note) |
|
Note: Wanted and interfering signal are placed adjacently around Fc |
||||
Table 7.4.1-2 Local Area BS in-channel selectivity for E-UTRA
|
E-UTRA channel bandwidth (MHz) |
Reference measurement channel |
Wanted signal mean power [dBm] |
Interfering signal mean power [dBm] |
Type of interfering signal |
|
1.4 |
A1-4 in Annex A.1 |
-98.9 |
-79 |
1.4 MHz E-UTRA signal, 3 RBs |
|
3 |
A1-5 in Annex A.1 |
-94.1 |
-76 |
3 MHz E-UTRA signal, 6 RBs |
|
5 |
A1-2 in Annex A.1 |
-92.0 |
-73 |
5 MHz E-UTRA signal, 10 RBs |
|
10 |
A1-3 in Annex A.1 (Note 3) A1-8 in Annex A.1 (Note 2) |
-90.5 -93.2 |
-69 -71.8 |
10 MHz E-UTRA signal, 25 RBs (Note 3) 10 MHz E-UTRA interlace signal, 10 RBs (Note 2) |
|
15 |
A1-3 in Annex A.1 (Note 1) |
-90.5 |
-69 |
15 MHz E-UTRA signal, 25 RBs (Note 1) |
|
20 |
A1-3 in Annex A.1 (Note 1) A1-9 in Annex A.1 (Note 2) |
-90.5 -93.2 |
-69 -71.8 |
20 MHz E-UTRA signal, 25 RBs (Note 1) 20 MHz E-UTRA interlace signal, 10 RBs (Note 2) |
|
Note 1: Wanted and interfering signal are placed adjacently around Fc, this reference measurement channel and interfering signal are not applied for Band 46 and Band 49. Note 2: Wanted and interfering signal interlaces are mirrored around Fc, this reference measurement channel and interfering signal are only applied for Band 46 and Band 49. Note 3: This reference measurement channel and interfering signal are not applied for Band 46 and Band 49. |
||||
Table 7.4.1-3 Home BS in-channel selectivity for E-UTRA
|
E-UTRA channel bandwidth (MHz) |
Reference measurement channel |
Wanted signal mean power [dBm] |
Interfering signal mean power [dBm] |
Type of interfering signal |
|
1.4 |
A1-4 in Annex A.1 |
-98.9 |
-79 |
1.4 MHz E-UTRA signal, 3 RBs |
|
3 |
A1-5 in Annex A.1 |
-94.1 |
-76 |
3 MHz E-UTRA signal, 6 RBs |
|
5 |
A1-2 in Annex A.1 |
-92.0 |
-73 |
5 MHz E-UTRA signal, 10 RBs |
|
10 |
A1-3 in Annex A.1 |
-90.5 |
-69 |
10 MHz E-UTRA signal, 25 RBs |
|
15 |
A1-3 in Annex A.1 (Note) |
-90.5 |
-69 |
15 MHz E-UTRA signal, 25 RBs (Note) |
|
20 |
A1-3 in Annex A.1 (Note) |
-90.5 |
-69 |
20 MHz E-UTRA signal, 25 RBs (Note) |
|
Note: Wanted and interfering signal are placed adjacently around Fc |
||||
Table 7.4.1-4 Medium Range BS in-channel selectivity for E-UTRA
|
E-UTRA channel bandwidth (MHz) |
Reference measurement channel |
Wanted signal mean power [dBm] |
Interfering signal mean power [dBm] |
Type of interfering signal |
|
1.4 |
A1-4 in Annex A.1 |
-101.9 |
-82 |
1.4 MHz E-UTRA signal, 3 RBs |
|
3 |
A1-5 in Annex A.1 |
-97.1 |
-79 |
3 MHz E-UTRA signal, 6 RBs |
|
5 |
A1-2 in Annex A.1 |
-95.0 |
-76 |
5 MHz E-UTRA signal, 10 RBs |
|
10 |
A1-3 in Annex A.1 (Note 3) A1-8 in Annex A.1 (Note 2) |
-93.5 -96.2 |
-72 -74.8 |
10 MHz E-UTRA signal, 25 RBs (Note 3) 10 MHz E-UTRA interlace signal, 10 RBs (Note 2) |
|
15 |
A1-3 in Annex A.1 (Note 1) |
-93.5 |
-72 |
15 MHz E-UTRA signal, 25 RBs (Note 1) |
|
20 |
A1-3 in Annex A.1 (Note 1) A1-9 in Annex A.1 (Note 2) |
-93.5 -96.2 |
-72 -74.8 |
20 MHz E-UTRA signal, 25 RBs (Note 1) 20 MHz E-UTRA interlace signal, 10 RBs (Note 2) |
|
Note 1: Wanted and interfering signal are placed adjacently around Fc, this reference measurement channel and interfering signal are not applied for Band 46. Note 2: Wanted and interfering signal interlaces are mirrored around Fc, this reference measurement channel and interfering signal are only applied for Band 46. Note 3: This reference measurement channel and interfering signal are not applied for Band 46. |
||||
For NB-IoT in-band operation, the throughput shall be ≥ 95% of the maximum throughput of the reference measurement channel as specified in Annex A with parameters specified in Table 7.4.1-5 and Table 7.4.1-6 for Wide Area BS.
Table 7.4.1-5 Wide Area BS in-channel selectivity for NB-IoT in-band operation with 15kHz channel spacing
|
E-UTRA channel bandwidth (MHz) |
Reference measurement channel |
Wanted signal mean power [dBm] |
Interfering signal mean power [dBm] |
Type of interfering signal |
|
3 |
FRC A14-1 in Annex A.14 |
-124.3 |
-84 |
3 MHz E-UTRA signal, 6 RBs (Note 2) |
|
5 |
FRC A14-1 in Annex A.14 |
-124.3 |
-81 |
5 MHz E-UTRA signal, 10 RBs (Note 1) |
|
10 |
FRC A14-1 in Annex A.14 |
-124.3 |
-77 |
10 MHz E-UTRA signal, 25 RBs (Note 1) |
|
15 |
FRC A14-1 in Annex A.14 |
-124.3 |
-77 |
15 MHz E-UTRA signal, 25 RBs (Note 1) |
|
20 |
FRC A14-1 in Annex A.14 |
-124.3 |
-77 |
20 MHz E-UTRA signal, 25 RBs (Note 1) |
|
Note 1: Interfering signal is placed in one side of the Fc, while the NB-IoT PRB is placed on the other side. Both interfering signal and NB-IoT PRB are placed at the middle of the available PRB locations. The wanted NB-IoT tone is placed at the centre of this NB-IoT PRB. Note 2: Interfering signal is placed from the edge of BWConfig, while the NB-IoT PRB is placed at the middle of the remaining PRB locations. The wanted NB-IoT tone is placed at the centre of this NB-IoT PRB. |
||||
Table 7.4.1-6 Wide Area BS in-channel selectivity for NB-IoT in-band operation with 3.75kHz channel spacing
|
E-UTRA channel bandwidth (MHz) |
Reference measurement channel |
Wanted signal mean power [dBm] |
Interfering signal mean power [dBm] |
Type of interfering signal |
|
3 |
FRC A14-2 in Annex A.14 |
-133.2+[3] |
-84 |
3 MHz E-UTRA signal, 6 RBs (Note 2) |
|
5 |
FRC A14-2 in Annex A.14 |
-133.2+[3] |
-81 |
5 MHz E-UTRA signal, 10 RBs (Note 1) |
|
10 |
FRC A14-2 in Annex A.14 |
-133.2+[3] |
-77 |
10 MHz E-UTRA signal, 25 RBs (Note 1) |
|
15 |
FRC A14-2 in Annex A.14 |
-133.2+[3] |
-77 |
15 MHz E-UTRA signal, 25 RBs (Note 1) |
|
20 |
FRC A14-2 in Annex A.14 |
-133.2+[3] |
-77 |
20 MHz E-UTRA signal, 25 RBs (Note 1) |
|
Note 1: Interfering signal is placed in one side of the Fc, while the NB-IoT PRB is placed on the other side. Both interfering signal and NB-IoT PRB are placed at the middle of the available PRB locations. The wanted NB-IoT tone is placed at the centre of this NB-IoT PRB. Note 2: Interfering signal is placed from the edge of BWConfig, while the NB-IoT PRB is placed at the middle of the remaining PRB locations. The wanted NB-IoT tone is placed at the centre of this NB-IoT PRB. |
||||
For NB-IoT in-band operation, the throughput shall be ≥ 95% of the maximum throughput of the reference measurement channel as specified in Annex A with parameters specified in Table 7.4.1-7 and Table 7.4.1-8 for Local Area BS.
Table 7.4.1-7 Local Area BS in-channel selectivity for NB-IoT in-band operation with 15kHz channel spacing
|
E-UTRA channel bandwidth (MHz) |
Reference measurement channel |
Wanted signal mean power [dBm] |
Interfering signal mean power [dBm] |
Type of interfering signal |
|
3 |
FRC A14-1 in Annex A.14 |
-116.3 |
-76 |
3 MHz E-UTRA signal, 6 RBs (Note 2) |
|
5 |
FRC A14-1 in Annex A.14 |
-116.3 |
-73 |
5 MHz E-UTRA signal, 10 RBs (Note 1) |
|
10 |
FRC A14-1 in Annex A.14 |
-116.3 |
-69 |
10 MHz E-UTRA signal, 25 RBs (Note 1) |
|
15 |
FRC A14-1 in Annex A.14 |
-116.3 |
-69 |
15 MHz E-UTRA signal, 25 RBs (Note 1) |
|
20 |
FRC A14-1 in Annex A.14 |
-116.3 |
-69 |
20 MHz E-UTRA signal, 25 RBs (Note 1) |
|
Note 1: Interfering signal is placed in one side of the Fc, while the NB-IoT PRB is placed on the other side. Both interfering signal and NB-IoT PRB are placed at the middle of the available PRB locations. The wanted NB-IoT tone is placed at the centre of this NB-IoT PRB. Note 2: Interfering signal is placed from the edge of BWConfig, while the NB-IoT PRB is placed at the middle of the remaining PRB locations. The wanted NB-IoT tone is placed at the centre of this NB-IoT PRB. |
||||
Table 7.4.1-8 Local Area BS in-channel selectivity for NB-IoT in-band operation with 3.75kHz channel spacing
|
E-UTRA channel bandwidth (MHz) |
Reference measurement channel |
Wanted signal mean power [dBm] |
Interfering signal mean power [dBm] |
Type of interfering signal |
|
3 |
FRC A14-2 in Annex A.14 |
-122.2 |
-76 |
3 MHz E-UTRA signal, 6 RBs (Note 2) |
|
5 |
FRC A14-2 in Annex A.14 |
-122.2 |
-73 |
5 MHz E-UTRA signal, 10 RBs (Note 1) |
|
10 |
FRC A14-2 in Annex A.14 |
-122.2 |
-69 |
10 MHz E-UTRA signal, 25 RBs (Note 1) |
|
15 |
FRC A14-2 in Annex A.14 |
-122.2 |
-69 |
15 MHz E-UTRA signal, 25 RBs (Note 1) |
|
20 |
FRC A14-2 in Annex A.14 |
-122.2 |
-69 |
20 MHz E-UTRA signal, 25 RBs (Note 1) |
|
Note 1: Interfering signal is placed in one side of the Fc, while the NB-IoT PRB is placed on the other side. Both interfering signal and NB-IoT PRB are placed at the middle of the available PRB locations. The wanted NB-IoT tone is placed at the centre of this NB-IoT PRB. Note 2: Interfering signal is placed from the edge of BWConfig, while the NB-IoT PRB is placed at the middle of the remaining PRB locations. The wanted NB-IoT tone is placed at the centre of this NB-IoT PRB. |
||||
For NB-IoT in-band operation, the throughput shall be ≥ 95% of the maximum throughput of the reference measurement channel as specified in Annex A with parameters specified in Table 7.4.1-9 and Table 7.4.1-10 for Home BS.
Table 7.4.1-9 Home BS in-channel selectivity for NB-IoT in-band operation with 15kHz channel spacing
|
E-UTRA channel bandwidth (MHz) |
Reference measurement channel |
Wanted signal mean power [dBm] |
Interfering signal mean power [dBm] |
Type of interfering signal |
|
3 |
FRC A14-1 in Annex A.14 |
-116.3 |
-76 |
3 MHz E-UTRA signal, 6 RBs (Note 2) |
|
5 |
FRC A14-1 in Annex A.14 |
-116.3 |
-73 |
5 MHz E-UTRA signal, 10 RBs (Note 1) |
|
10 |
FRC A14-1 in Annex A.14 |
-116.3 |
-69 |
10 MHz E-UTRA signal, 25 RBs (Note 1) |
|
15 |
FRC A14-1 in Annex A.14 |
-116.3 |
-69 |
15 MHz E-UTRA signal, 25 RBs (Note 1) |
|
20 |
FRC A14-1 in Annex A.14 |
-116.3 |
-69 |
20 MHz E-UTRA signal, 25 RBs (Note 1) |
|
Note 1: Interfering signal is placed in one side of the Fc, while the NB-IoT PRB is placed on the other side. Both interfering signal and NB-IoT PRB are placed at the middle of the available PRB locations. The wanted NB-IoT tone is placed at the centre of this NB-IoT PRB. Note 2: Interfering signal is placed from the edge of BWConfig, while the NB-IoT PRB is placed at the middle of the remaining PRB locations. The wanted NB-IoT tone is placed at the centre of this NB-IoT PRB. |
||||
Table 7.4.1-10 Home BS in-channel selectivity for NB-IoT in-band operation with 3.75kHz channel spacing
|
E-UTRA channel bandwidth (MHz) |
Reference measurement channel |
Wanted signal mean power [dBm] |
Interfering signal mean power [dBm] |
Type of interfering signal |
|
3 |
FRC A14-2 in Annex A.14 |
-122.2 |
-76 |
3 MHz E-UTRA signal, 6 RBs (Note 2) |
|
5 |
FRC A14-2 in Annex A.14 |
-122.2 |
-73 |
5 MHz E-UTRA signal, 10 RBs (Note 1) |
|
10 |
FRC A14-2 in Annex A.14 |
-122.2 |
-69 |
10 MHz E-UTRA signal, 25 RBs (Note 1) |
|
15 |
FRC A14-2 in Annex A.14 |
-122.2 |
-69 |
15 MHz E-UTRA signal, 25 RBs (Note 1) |
|
20 |
FRC A14-2 in Annex A.14 |
-122.2 |
-69 |
20 MHz E-UTRA signal, 25 RBs (Note 1) |
|
Note 1: Interfering signal is placed in one side of the Fc, while the NB-IoT PRB is placed on the other side. Both interfering signal and NB-IoT PRB are placed at the middle of the available PRB locations. The wanted NB-IoT tone is placed at the centre of this NB-IoT PRB. Note 2: Interfering signal is placed from the edge of BWConfig, while the NB-IoT PRB is placed at the middle of the remaining PRB locations. The wanted NB-IoT tone is placed at the centre of this NB-IoT PRB. |
||||
For NB-IoT in-band operation, the throughput shall be ≥ 95% of the maximum throughput of the reference measurement channel as specified in Annex A with parameters specified in Table 7.4.1-11 and Table 7.4.1-12 for Medium Range BS.
Table 7.4.1-11 Medium Range BS in-channel selectivity for NB-IoT in-band operation with 15kHz channel spacing
|
E-UTRA channel bandwidth (MHz) |
Reference measurement channel |
Wanted signal mean power [dBm] |
Interfering signal mean power [dBm] |
Type of interfering signal |
|
3 |
FRC A14-1 in Annex A.14 |
-119.3 |
-79 |
3 MHz E-UTRA signal, 6 RBs (Note 2) |
|
5 |
FRC A14-1 in Annex A.14 |
-119.3 |
-76 |
5 MHz E-UTRA signal, 10 RBs (Note 1) |
|
10 |
FRC A14-1 in Annex A.14 |
-119.3 |
-72 |
10 MHz E-UTRA signal, 25 RBs (Note 1) |
|
15 |
FRC A14-1 in Annex A.14 |
-119.3 |
-72 |
15 MHz E-UTRA signal, 25 RBs (Note 1) |
|
20 |
FRC A14-1 in Annex A.14 |
-119.3 |
-72 |
20 MHz E-UTRA signal, 25 RBs (Note 1) |
|
Note 1: Interfering signal is placed in one side of the Fc, while the NB-IoT PRB is placed on the other side. Both interfering signal and NB-IoT PRB are placed at the middle of the available PRB locations. The wanted NB-IoT tone is placed at the centre of this NB-IoT PRB. Note 2: Interfering signal is placed from the edge of BWConfig, while the NB-IoT PRB is placed at the middle of the remaining PRB locations. The wanted NB-IoT tone is placed at the centre of this NB-IoT PRB. |
||||
Table 7.4.1-12 Medium Range BS in-channel selectivity for NB-IoT in-band operation with 3.75kHz channel spacing
|
E-UTRA channel bandwidth (MHz) |
Reference measurement channel |
Wanted signal mean power [dBm] |
Interfering signal mean power [dBm] |
Type of interfering signal |
|
3 |
FRC A14-2 in Annex A.14 |
-125.2 |
-79 |
3 MHz E-UTRA signal, 6 RBs (Note 2) |
|
5 |
FRC A14-2 in Annex A.14 |
-125.2 |
-76 |
5 MHz E-UTRA signal, 10 RBs (Note 1) |
|
10 |
FRC A14-2 in Annex A.14 |
-125.2 |
-72 |
10 MHz E-UTRA signal, 25 RBs (Note 1) |
|
15 |
FRC A14-2 in Annex A.14 |
-125.2 |
-72 |
15 MHz E-UTRA signal, 25 RBs (Note 1) |
|
20 |
FRC A14-2 in Annex A.14 |
-125.2 |
-72 |
20 MHz E-UTRA signal, 25 RBs (Note 1) |
|
Note 1: Interfering signal is placed in one side of the Fc, while the NB-IoT PRB is placed on the other side. Both interfering signal and NB-IoT PRB are placed at the middle of the available PRB locations. The wanted NB-IoT tone is placed at the centre of this NB-IoT PRB. Note 2: Interfering signal is placed from the edge of BWConfig, while the NB-IoT PRB is placed at the middle of the remaining PRB locations. The wanted NB-IoT tone is placed at the centre of this NB-IoT PRB. |
||||