6.6.3 Operating band unwanted emissions
36.1043GPPBase Station (BS) radio transmission and receptionEvolved Universal Terrestrial Radio Access (E-UTRA)Release 18TS
Unless otherwise stated, the Operating band unwanted emission limits are defined from 10 MHz below the lowest frequency of each supported downlink operating band up to 10 MHz above the highest frequency of each supported downlink operating band.
The requirements shall apply whatever the type of transmitter considered (single carrier or multi-carrier) and for all transmission modes foreseen by the manufacturer’s specification. In addition, for a BS operating in non-contiguous spectrum, the requirements apply inside any sub-block gap. In addition, for a BS operating in multiple bands, the requirements apply inside any Inter RF Bandwidth gap.
For BS capable of multi-band operation where multiple bands are mapped on separate antenna connectors, the single-band requirements apply and the cumulative evaluation of the emission limit in the Inter RF Bandwidth gap are not applicable.
For a BS supporting E-UTRA with NB-IoT guard band operation, the Operating band unwanted emissions requirements apply to E-UTRA carrier with channel bandwidth larger than or equal to 5 MHz.
The unwanted emission limits in the part of the downlink operating band that falls in the spurious domain are consistent with ITU-R Recommendation SM.329 [2].
Emissions shall not exceed the maximum levels specified in the tables below, where:
– Δf is the separation between the Base Station RF Bandwidth edge frequency and the nominal -3dB point of the measuring filter closest to the carrier frequency.
– f_offset is the separation between the Base Station RF Bandwidth edge frequency and the centre of the measuring filter.
– f_offsetmax is the offset to the frequency 10 MHz outside the downlink operating band.
– Δfmax is equal to f_offsetmax minus half of the bandwidth of the measuring filter.
For E-UTRA or E-UTRA with NB-IoT (in-band and/or guard band) BS operating in multiple bands, inside any Inter RF Bandwidth gaps with Wgap < 20 MHz, emissions shall not exceed the cumulative sum of the minimum requirements specified at the Base Station RF Bandwidth edges on each side of the Inter RF Bandwidth gap. The minimum requirement for Base Station RF Bandwidth edge is specified in Tables 6.6.3.1-1 to 6.6.3.3-3 below, where in this case:
– Δf is the separation between the Base Station RF Bandwidth edge frequency and the nominal -3 dB point of the measuring filter closest to the Base Station RF Bandwidth edge.
– f_offset is the separation between the Base Station RF Bandwidth edge frequency and the centre of the measuring filter.
– f_offsetmax is equal to the Inter RF Bandwidth gap minus half of the bandwidth of the measuring filter.
– Δfmax is equal to f_offsetmax minus half of the bandwidth of the measuring filter.
For BS capable of multi-band operation where multiple bands are mapped on the same antenna connector, the operating band unwanted emission limits apply also in a supported operating band without any carrier transmitted, in the case where there are carrier(s) transmitted in other supported operating band(s). In this case where there is no carrier transmitted in an operating band, the operating band unwanted emission limit, as defined in the tables of the present clause for the largest frequency offset (Δfmax), of a band where there is no carrier transmitted shall apply from 10 MHz below the lowest frequency, up to 10 MHz above the highest frequency of the supported downlink operating band without any carrier transmitted. And no cumulative limit is applied in the inter-band gap between a supported downlink operating band with carrier(s) transmitted and a supported downlink operating band without any carrier transmitted.
For a multicarrier E-UTRA BS or BS configured for intra-band contiguous or non-contiguous carrier aggregation the definitions above apply to the lower edge of the carrier transmitted at the lowest carrier frequency and the upper edge of the carrier transmitted at the highest carrier frequency within a specified frequency band.
In addition inside any sub-block gap for a BS operating in non-contiguous spectrum, emissions shall not exceed the cumulative sum of the minimum requirements specified for the adjacent sub blocks on each side of the sub block gap. The minimum requirement for each sub block is specified in Tables 6.6.3.1-1 to 6.6.3.3-3 below, where in this case:
– Δf is the separation between the sub block edge frequency and the nominal -3 dB point of the measuring filter closest to the sub block edge.
– f_offset is the separation between the sub block edge frequency and the centre of the measuring filter.
– f_offsetmax is equal to the sub block gap bandwidth minus half of the bandwidth of the measuring filter.
– Δfmax is equal to f_offsetmax minus half of the bandwidth of the measuring filter.
For Wide Area BS, the requirements of either clause 6.6.3.1 (Category A limits) or clause 6.6.3.2 (Category B limits) shall apply.
For Local Area BS, the requirements of clause 6.6.3.2A shall apply (Category A and B).
For Home BS, the requirements of clause 6.6.3.2B shall apply (Category A and B).
For Medium Range BS, the requirements in clause 6.6.3.2C shall apply (Category A and B).
The application of either Category A or Category B limits shall be the same as for Transmitter spurious emissions (Mandatory Requirements) in clause 6.6.4.1.
The requirements of clauses 6.6.3.1 and 6.6.3.2 apply to Wide Area BS that supports E-UTRA or E-UTRA with NB-IoT (in-band and/or guard band). The requirements for Wide Area BS that supports NB-IoT standalone are in clause 6.6.3.2E.
The requirements of clauses 6.6.3.2A apply to Local Area BS that supports E-UTRA or E-UTRA with NB-IoT (in-band and/or guard band). The requirements for Local Area BS that supports NB-IoT standalone are in clause 6.6.3.2F.
The requirements of clauses 6.6.3.2B apply to Home BS that supports E-UTRA or E-UTRA with NB-IoT (in-band and/or guard band). The requirements for Home BS that supports NB-IoT standalone are in clause 6.6.3.2G.
The requirements of clauses 6.6.3.2C apply to Medium Range BS that supports E-UTRA or E-UTRA with NB-IoT (in-band and/or guard band). The requirements for Medium Range BS that supports NB-IoT standalone are in clause 6.6.3.2H.
6.6.3.1 Minimum requirements for Wide Area BS (Category A)
For E-UTRA BS operating in Bands 5, 6, 8, 12, 13, 14, 17, 18, 19, 26, 27, 28, 29, 31, 44, 68, 71, 72, 73, 85, 87, 88 emissions shall not exceed the maximum levels specified in Tables 6.6.3.1‑1 to 6.6.3.1-3.
Table 6.6.3.1-1: Wide Area BS operating band unwanted emission limits for 1.4 MHz channel bandwidth (E‑UTRA bands <1GHz) for Category A
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 1.4 MHz |
0.05 MHz ≤ f_offset < 1.45 MHz |
|
100 kHz |
|
1.4 MHz ≤ Δf < 2.8 MHz |
1.45 MHz ≤ f_offset < 2.85 MHz |
-11 dBm |
100 kHz |
|
2.8 MHz ≤ Δf ≤ Δfmax |
2.85 MHz ≤ f_offset < f_offsetmax |
-13 dBm |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -13dBm/100kHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap. |
|||
Table 6.6.3.1-2: Wide Area BS operating band unwanted emission limits for 3 MHz channel bandwidth (E‑UTRA bands <1GHz) for Category A
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 3 MHz |
0.05 MHz ≤ f_offset < 3.05 MHz |
|
100 kHz |
|
3 MHz ≤ Δf < 6 MHz |
3.05 MHz ≤ f_offset < 6.05 MHz |
-15 dBm |
100 kHz |
|
6 MHz ≤ Δf ≤ Δfmax |
6.05 MHz ≤ f_offset < f_offsetmax |
-13 dBm |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -13dBm/100kHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap. |
|||
Table 6.6.3.1-3: Wide Area BS operating band unwanted emission limits for 5, 10, 15 and 20 MHz channel bandwidth (E-UTRA bands <1GHz) for Category A
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 5 MHz |
0.05 MHz ≤ f_offset < 5.05 MHz |
|
100 kHz |
|
5 MHz ≤ Δf < min(10 MHz, Δfmax) |
5.05 MHz ≤ f_offset < min(10.05 MHz, f_offsetmax) |
-14 dBm |
100 kHz |
|
10 MHz ≤ Δf ≤ Δfmax |
10.05 MHz ≤ f_offset < f_offsetmax |
-13 dBm (Note 10) |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -13dBm/100kHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap. |
|||
For E-UTRA BS operating in Bands 1, 2, 3, 4, 7, 9, 10, 11, 21, 22, 23, 24, 25, 30, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 45, 48, 50, 52, 54, 65, 66, 69, 70, 74, 75 emissions shall not exceed the maximum levels specified in Tables 6.6.3.1-4 to 6.6.3.1-6:
Table 6.6.3.1-4: Wide Area BS operating band unwanted emission limits for 1.4 MHz channel bandwidth (E‑UTRA bands >1GHz) for Category A
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 1.4 MHz |
0.05 MHz ≤ f_offset < 1.45 MHz |
|
100 kHz |
|
1.4 MHz ≤ Δf < 2.8 MHz |
1.45 MHz ≤ f_offset < 2.85 MHz |
-11 dBm |
100 kHz |
|
2.8 MHz ≤ Δf ≤ Δfmax |
3.3 MHz ≤ f_offset < f_offsetmax |
-13 dBm |
1MHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap, where the contribution from the far-end sub-block shall be scaled according to the measurement bandwidth of the near-end sub-block. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -13dBm/1MHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap, where the contribution from the far-end sub-block or RF Bandwidth shall be scaled according to the measurement bandwidth of the near-end sub-block or RF Bandwidth. |
|||
Table 6.6.3.1-5: Wide Area BS operating band unwanted emission limits for 3 MHz channel bandwidth (E‑UTRA bands >1GHz) for Category A
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 3 MHz |
0.05 MHz ≤ f_offset < 3.05 MHz |
|
100 kHz |
|
3 MHz ≤ Δf < 6 MHz |
3.05 MHz ≤ f_offset < 6.05 MHz |
-15 dBm |
100 kHz |
|
6 MHz ≤ Δf ≤ Δfmax |
6.5 MHz ≤ f_offset < f_offsetmax |
-13 dBm |
1MHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap, where the contribution from the far-end sub-block shall be scaled according to the measurement bandwidth of the near-end sub-block. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -13dBm/1MHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap, where the contribution from the far-end sub-block or RF Bandwidth shall be scaled according to the measurement bandwidth of the near-end sub-block or RF Bandwidth. |
|||
Table 6.6.3.1-6: Wide Area BS operating band unwanted emission limits for 5, 10, 15 and 20 MHz channel bandwidth (E-UTRA bands >1GHz) for Category A
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 5 MHz |
0.05 MHz ≤ f_offset < 5.05 MHz |
|
100 kHz |
|
5 MHz ≤ Δf < min(10 MHz, Δfmax) |
5.05 MHz ≤ f_offset < min(10.05 MHz, f_offsetmax) |
-14 dBm |
100 kHz |
|
10 MHz ≤ Δf ≤ Δfmax |
10.5 MHz ≤ f_offset < f_offsetmax |
-13 dBm (Note 10) |
1MHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap, where the contribution from the far-end sub-block shall be scaled according to the measurement bandwidth of the near-end sub-block. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -13dBm/1MHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap, where the contribution from the far-end sub-block or RF Bandwidth shall be scaled according to the measurement bandwidth of the near-end sub-block or RF Bandwidth. |
|||
6.6.3.2 Minimum requirements for Wide Area BS (Category B)
For Category B Operating band unwanted emissions, there are two options for the limits that may be applied regionally. Either the limits in clause 6.6.3.2.1 or clause 6.6.3.2.2 shall be applied.
6.6.3.2.1 Category B requirements (Option 1)
For E-UTRA BS operating in Bands 5, 8, 12, 13, 14, 17, 20, 26, 27, 28, 29, 31, 44, 68, 67, 71, 72, 73, 85, 87, 88 emissions shall not exceed the maximum levels specified in Tables 6.6.3.2.1-1 to 6.6.3.2.1-3:
Table 6.6.3.2.1-1: Wide Area BS operating band unwanted emission limits for 1.4 MHz channel bandwidth (E‑UTRA bands <1GHz) for Category B
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 1.4 MHz |
0.05 MHz ≤ f_offset < 1.45 MHz |
|
100 kHz |
|
1.4 MHz ≤ Δf < 2.8 MHz |
1.45 MHz ≤ f_offset < 2.85 MHz |
-11 dBm |
100 kHz |
|
2.8 MHz ≤ Δf ≤ Δfmax |
2.85 MHz ≤ f_offset < f_offsetmax |
-16 dBm |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -16dBm/100kHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap. |
|||
Table 6.6.3.2.1-2: Wide Area BS operating band unwanted emission limits for 3 MHz channel bandwidth (E‑UTRA bands <1GHz) for Category B
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 3 MHz |
0.05 MHz ≤ f_offset < 3.05 MHz |
|
100 kHz |
|
3 MHz ≤ Δf < 6 MHz |
3.05 MHz ≤ f_offset < 6.05 MHz |
-15 dBm |
100 kHz |
|
6 MHz ≤ Δf ≤ Δfmax |
6.05 MHz ≤ f_offset < f_offsetmax |
-16 dBm |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -16dBm/100kHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap. |
|||
Table 6.6.3.2.1-3: Wide Area BS operating band unwanted emission limits for 5, 10, 15 and 20 MHz channel bandwidth (E-UTRA bands <1GHz) for Category B
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 5 MHz |
0.05 MHz ≤ f_offset < 5.05 MHz |
|
100 kHz |
|
5 MHz ≤ Δf < min(10 MHz, Δfmax) |
5.05 MHz ≤ f_offset < min(10.05 MHz, f_offsetmax) |
-14 dBm |
100 kHz |
|
10 MHz ≤ Δf ≤ Δfmax |
10.05 MHz ≤ f_offset < f_offsetmax |
-16 dBm (Note 10) |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -16dBm/100kHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap. |
|||
For E-UTRA BS operating in Bands 1, 2, 3, 4, 7, 10, 22, 25, 30, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 45, 48, 50, 52, 65, 66, 69, 70, 75 emissions shall not exceed the maximum levels specified in Tables 6.6.3.2.1-4 to 6.6.3.2.1-6:
Table 6.6.3.2.1-4: Wide Area BS operating band unwanted emission limits for 1.4 MHz channel bandwidth (E‑UTRA bands >1GHz) for Category B
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 1.4 MHz |
0.05 MHz ≤ f_offset < 1.45 MHz |
|
100 kHz |
|
1.4 MHz ≤ Δf < 2.8 MHz |
1.45 MHz ≤ f_offset < 2.85 MHz |
-11 dBm |
100 kHz |
|
2.8 MHz ≤ Δf ≤ Δfmax |
3.3 MHz ≤ f_offset < f_offsetmax |
-15 dBm |
1MHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap, where the contribution from the far-end sub-block shall be scaled according to the measurement bandwidth of the near-end sub-block. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -15dBm/1MHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap, where the contribution from the far-end sub-block or RF Bandwidth shall be scaled according to the measurement bandwidth of the near-end sub-block or RF Bandwidth. |
|||
Table 6.6.3.2.1-5: Wide Area BS operating band unwanted emission limits for 3 MHz channel bandwidth (E‑UTRA bands >1GHz) for Category B
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 3 MHz |
0.05 MHz ≤ f_offset < 3.05 MHz |
|
100 kHz |
|
3 MHz ≤ Δf < 6 MHz |
3.05 MHz ≤ f_offset < 6.05 MHz |
-15 dBm |
100 kHz |
|
6 MHz ≤ Δf ≤ Δfmax |
6.5 MHz ≤ f_offset < f_offsetmax |
-15 dBm |
1MHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap, where the contribution from the far-end sub-block shall be scaled according to the measurement bandwidth of the near-end sub-block. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -15dBm/1MHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap, where the contribution from the far-end sub-block or RF Bandwidth shall be scaled according to the measurement bandwidth of the near-end sub-block or RF Bandwidth. |
|||
Table 6.6.3.2.1-6: Wide Area BS operating band unwanted emission limits for 5, 10, 15 and 20 MHz channel bandwidth (E-UTRA bands >1GHz) for Category B
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 5 MHz |
0.05 MHz ≤ f_offset < 5.05 MHz |
|
100 kHz |
|
5 MHz ≤ Δf < min(10 MHz, Δfmax) |
5.05 MHz ≤ f_offset < min(10.05 MHz, f_offsetmax) |
-14 dBm |
100 kHz |
|
10 MHz ≤ Δf ≤ Δfmax |
10.5 MHz ≤ f_offset < f_offsetmax |
-15 dBm (Note 10) |
1MHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap, where the contribution from the far-end sub-block shall be scaled according to the measurement bandwidth of the near-end sub-block. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -15dBm/1MHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap, where the contribution from the far-end sub-block or RF Bandwidth shall be scaled according to the measurement bandwidth of the near-end sub-block or RF Bandwidth. |
|||
6.6.3.2.2 Category B (Option 2)
The limits in this clause are intended for Europe and may be applied regionally for BS operating in band 1, 3, 7, 8, 32, 33, 34, 38, 65 or 69.
For a BS operating in band 1, 3, 7, 8, 32, 33, 34, 38, 65 or 69 emissions shall not exceed the maximum levels specified in Table 6.6.3.2.2-1 below for 5, 10, 15 and 20 MHz channel bandwidth:
Table 6.6.3.2.2-1: Regional Wide Area BS operating band unwanted emission limits in band 1, 3, 7, 8, 32, 33, 34, 38, 65 or 69 for 5, 10, 15 and 20 MHz channel bandwidth for Category B
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 0.2 MHz |
0.015MHz ≤ f_offset < 0.215MHz |
-14 dBm |
30 kHz |
|
0.2 MHz ≤ Δf < 1 MHz |
0.215MHz ≤ f_offset < 1.015MHz |
|
30 kHz |
|
(Note 9) |
1.015MHz ≤ f_offset < 1.5 MHz |
-26 dBm |
30 kHz |
|
1 MHz ≤ Δf ≤ min( 10 MHz, Δfmax) |
1.5 MHz ≤ f_offset < min(10.5 MHz, f_offsetmax) |
-13 dBm |
1 MHz |
|
10 MHz ≤ Δf ≤ Δfmax |
10.5 MHz ≤ f_offset < f_offsetmax |
-15 dBm (Note 10) |
1 MHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap, where the contribution from the far-end sub-block shall be scaled according to the measurement bandwidth of the near-end sub-block. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -15dBm/1MHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap, where the contribution from the far-end sub-block or RF Bandwidth shall be scaled according to the measurement bandwidth of the near-end sub-block or RF Bandwidth. |
|||
For a BS operating in band 3, 8 or 65, emissions shall not exceed the maximum levels specified in Table 6.6.3.2.2‑2 below for 3 MHz channel bandwidth:
Table 6.6.3.2.2-2: Regional Wide Area BS operating band unwanted emission limits in band 3, 8 or 65 for 3 MHz channel bandwidth for Category B
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 0.05 MHz |
0.015 MHz ≤ f_offset < 0.065 MHz |
|
30 kHz |
|
0.05 MHz ≤ Δf < 0.15 MHz |
0. 065 MHz ≤ f_offset < 0.165 MHz |
|
30 kHz |
|
0.15 MHz ≤ Δf < 0.2 MHz |
0.165MHz ≤ f_offset < 0.215MHz |
-14 dBm |
30 kHz |
|
0.2 MHz ≤ Δf < 1 MHz |
0.215MHz ≤ f_offset < 1.015MHz |
|
30 kHz |
|
(Note 9) |
1.015MHz ≤ f_offset < 1.5 MHz |
-26 dBm |
30 kHz |
|
1 MHz ≤ Δf ≤ 6 MHz |
1.5 MHz ≤ f_offset < 6.5 MHz |
-13 dBm |
1 MHz |
|
6 MHz ≤ Δf ≤ Δfmax |
6.5 MHz ≤ f_offset < f_offsetmax |
-15 dBm |
1 MHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap, where the contribution from the far-end sub-block shall be scaled according to the measurement bandwidth of the near-end sub-block. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -15dBm/1MHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap, where the contribution from the far-end sub-block or RF Bandwidth shall be scaled according to the measurement bandwidth of the near-end sub-block or RF Bandwidth. |
|||
For a BS operating in band 3, 8 or 65, emissions shall not exceed the maximum levels specified in Table 6.6.3.2.2‑3 below for 1.4 MHz channel bandwidth:
Table 6.6.3.2.2-3: Regional Wide Area BS operating band unwanted emission limits in band 3, 8 or 65 for 1.4 MHz channel bandwidth for Category B
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 0.05 MHz |
0.015 MHz ≤ f_offset < 0.065 MHz |
|
30 kHz |
|
0.05 MHz ≤ Δf < 0.15 MHz |
0. 065 MHz ≤ f_offset < 0.165 MHz |
|
30 kHz |
|
0.15 MHz ≤ Δf < 0.2 MHz |
0.165MHz ≤ f_offset < 0.215MHz |
-14 dBm |
30 kHz |
|
0.2 MHz ≤ Δf < 1 MHz |
0.215MHz ≤ f_offset < 1.015MHz |
|
30 kHz |
|
(Note 9) |
1.015MHz ≤ f_offset < 1.5 MHz |
-26 dBm |
30 kHz |
|
1 MHz ≤ Δf ≤ 2.8 MHz |
1.5 MHz ≤ f_offset < 3.3 MHz |
-13 dBm |
1 MHz |
|
2.8 MHz ≤ Δf ≤ Δfmax |
3.3 MHz ≤ f_offset < f_offsetmax |
-15 dBm |
1 MHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap, where the contribution from the far-end sub-block shall be scaled according to the measurement bandwidth of the near-end sub-block. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -15dBm/1MHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap, where the contribution from the far-end sub-block or RF Bandwidth shall be scaled according to the measurement bandwidth of the near-end sub-block or RF Bandwidth. |
|||
6.6.3.2A Minimum requirements for Local Area BS (Category A and B)
For Local Area BS, emissions shall not exceed the maximum levels specified in Tables 6.6.3.2A-1 to 6.6.3.2A-3.
Table 6.6.3.2A-1: Local Area BS operating band unwanted emission limits for 1.4 MHz channel bandwidth
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 1.4 MHz |
0.05 MHz ≤ f_offset < 1.45 MHz |
|
100 kHz |
|
1.4 MHz ≤ Δf < 2.8 MHz |
1.45 MHz ≤ f_offset < 2.85 MHz |
-31 dBm |
100 kHz |
|
2.8 MHz ≤ Δf ≤ Δfmax |
2.85 MHz ≤ f_offset < f_offsetmax |
-31 dBm |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -31dBm/100kHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap. |
|||
Table 6.6.3.2A-2: Local Area BS operating band unwanted emission limits for 3 MHz channel bandwidth
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 3 MHz |
0.05 MHz ≤ f_offset < 3.05 MHz |
|
100 kHz |
|
3 MHz ≤ Δf < 6 MHz |
3.05 MHz ≤ f_offset < 6.05 MHz |
-35 dBm |
100 kHz |
|
6 MHz ≤ Δf ≤ Δfmax |
6.05 MHz ≤ f_offset < f_offsetmax |
-35 dBm |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -35dBm/100kHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap. |
|||
Table 6.6.3.2A-3: Local Area BS operating band unwanted emission limits for 5, 10, 15 and 20 MHz channel bandwidth
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2)) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 5 MHz |
0.05 MHz ≤ f_offset < 5.05 MHz |
|
100 kHz |
|
5 MHz ≤ Δf < min(10 MHz, Δfmax) |
5.05 MHz ≤ f_offset < min(10.05 MHz, f_offsetmax) |
-37 dBm |
100 kHz |
|
10 MHz ≤ Δf ≤ Δfmax |
10.05 MHz ≤ f_offset < f_offsetmax |
-37 dBm (Note 10) |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -37dBm/100kHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap. |
|||
6.6.3.2B Minimum requirements for Home BS (Category A and B)
For Home BS, emissions shall not exceed the maximum levels specified in Tables 6.6.3.2B-1 to 6.6.3.2B-3.
Table 6.6.3.2B-1: Home BS operating band unwanted emission limits for 1.4 MHz channel bandwidth
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 1.4 MHz |
0.05 MHz ≤ f_offset < 1.45 MHz |
|
100 kHz |
|
1.4 MHz ≤ Δf < 2.8 MHz |
1.45 MHz ≤ f_offset < 2.85 MHz |
-36 dBm |
100 kHz |
|
2.8 MHz ≤ Δf ≤ Δfmax |
3.3 MHz ≤ f_offset < f_offsetmax |
(Note 11) |
1MHz |
Table 6.6.3.2B-2: Home BS operating band unwanted emission limits for 3 MHz channel bandwidth
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 3 MHz |
0.05 MHz ≤ f_offset < 3.05 MHz |
|
100 kHz |
|
3 MHz ≤ Δf < 6 MHz |
3.05 MHz ≤ f_offset < 6.05 MHz |
-40 dBm |
100 kHz |
|
6 MHz ≤ Δf ≤ Δfmax |
6.5 MHz ≤ f_offset < f_offsetmax |
(Note 11) |
1MHz |
Table 6.6.3.2B-3: Home BS operating band unwanted emission limits for 5, 10, 15 and 20 MHz channel bandwidth
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 5 MHz |
0.05 MHz ≤ f_offset < 5.05 MHz |
|
100 kHz |
|
5 MHz ≤ Δf < min(10 MHz, Δfmax) |
5.05 MHz ≤ f_offset < min(10.05 MHz, f_offsetmax) |
-42 dBm |
100 kHz |
|
10 MHz ≤ Δf ≤ Δfmax |
10.5 MHz ≤ f_offset < f_offsetmax |
(Note 10, Note 11) |
1MHz |
6.6.3.2C Minimum requirements for Medium Range BS (Category A and B)
For Medium Range BS, emissions shall not exceed the maximum levels specified in Tables 6.6.3.2C-1 to 6.6.3.2C-6.
Table 6.6.3.2C-1: Medium Range BS operating band unwanted emission limits for 1.4 MHz channel bandwidth, 31 < Prated,c ≤ 38 dBm
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 1.4 MHz |
0.05 MHz ≤ f_offset < 1.45 MHz |
|
100 kHz |
|
1.4 MHz ≤ Δf < 2.8 MHz |
1.45 MHz ≤ f_offset < 2.85 MHz |
Prated,c -55dB |
100 kHz |
|
2.8 MHz ≤ Δf ≤ Δfmax |
2.85 MHz ≤ f_offset < f_offsetmax |
-25dBm |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -25dBm/100kHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap. |
|||
Table 6.6.3.2C-2: Medium Range BS operating band unwanted emission limits for 1.4 MHz channel bandwidth, Prated,c ≤ 31 dBm
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 1.4 MHz |
0.05 MHz ≤ f_offset < 1.45 MHz |
|
100 kHz |
|
1.4 MHz ≤ Δf < 2.8 MHz |
1.45 MHz ≤ f_offset < 2.85 MHz |
-24 dBm |
100 kHz |
|
2.8 MHz ≤ Δf ≤ Δfmax |
2.85 MHz ≤ f_offset < f_offsetmax |
-25dBm |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -25dBm/100kHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap. |
|||
Table 6.6.3.2C-3: Medium Range BS operating band unwanted emission limits for 3 MHz channel bandwidth, 31 < Prated,c ≤ 38 dBm
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 3 MHz |
0.05 MHz ≤ f_offset < 3.05 MHz |
|
100 kHz |
|
3 MHz ≤ Δf < 6 MHz |
3.05 MHz ≤ f_offset < 6.05 MHz |
Prated,c -59dB |
100 kHz |
|
6 MHz ≤ Δf ≤ Δfmax |
6.05 MHz ≤ f_offset < f_offsetmax |
Min(Prated,c -59dB, -25dBm) |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be Min(Prated,c -59dB, -25dBm)/100kHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap. |
|||
Table 6.6.3.2C-4: Medium Range BS operating band unwanted emission limits for 3 MHz channel bandwidth, Prated,c ≤ 31 dBm
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 3 MHz |
0.05 MHz ≤ f_offset < 3.05 MHz |
|
100 kHz |
|
3 MHz ≤ Δf < 6 MHz |
3.05 MHz ≤ f_offset < 6.05 MHz |
-28 dBm |
100 kHz |
|
6 MHz ≤ Δf ≤ Δfmax |
6.05 MHz ≤ f_offset < f_offsetmax |
-28 dBm |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -28dBm/100kHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap. |
|||
Table 6.6.3.2C-5: Medium Range BS operating band unwanted emission limits for 5, 10, 15 and 20 MHz channel bandwidth, 31< Prated,c ≤ 38 dBm
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 5 MHz |
0.05 MHz ≤ f_offset < 5.05 MHz |
|
100 kHz |
|
5 MHz ≤ Δf < min(10 MHz, Δfmax) |
5.05 MHz ≤ f_offset < min(10.05 MHz, f_offsetmax) |
Prated,c -60dB |
100 kHz |
|
10 MHz ≤ Δf ≤ Δfmax |
10.05 MHz ≤ f_offset < f_offsetmax |
Min(Prated,c -60dB, -25dBm) (Note 9) |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be Min(Prated,c -60dB, -25dBm)/100kHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap. |
|||
Table 6.6.3.2C-6: Medium Range BS operating band unwanted emission limits for 5, 10, 15 and 20 MHz channel bandwidth, Prated,c ≤ 31 dBm
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 5 MHz |
0.05 MHz ≤ f_offset < 5.05 MHz |
|
100 kHz |
|
5 MHz ≤ Δf < min(10 MHz, Δfmax) |
5.05 MHz ≤ f_offset < min(10.05 MHz, f_offsetmax) |
-29 dBm |
100 kHz |
|
10 MHz ≤ Δf ≤ Δfmax |
10.05 MHz ≤ f_offset < f_offsetmax |
-29 dBm (Note 9) |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 10MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be -29dBm/100kHz. NOTE 2: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap. |
|||
6.6.3.2D Minimum requirements for Local Area and Medium Range BS in Band 46 (Category A and B)
For Local Area and Medium Range BS operating in Band 46, emissions shall not exceed the maximum levels specified in Tables 6.6.3.2D-1 and Tables 6.6.3.2D-2.
Table 6.6.3.2D-1: Local Area and Medium Range BS operating band unwanted emission limits in Band 46 for 20MHz channel bandwidth
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 1 MHz |
0.05 MHz ≤ f_offset < 1.05 MHz |
|
100 kHz |
|
1 MHz ≤ Δf < min(10 MHz, Δfmax) |
1.05 MHz ≤ f_offset < min(10.05 MHz, f_offsetmax) |
|
100 kHz |
|
10 MHz ≤ Δf < min(20 MHz, Δfmax) |
10.05 MHz ≤ f_offset < min(20.05 MHz, f_offsetmax) |
|
100 kHz |
|
20 MHz ≤ Δf < min(170 MHz, Δfmax) |
20.05 MHz ≤ f_offset < min(170.05 MHz, f_offsetmax) |
Max(Prated,c – 62.6dB, -40dBm) |
100 kHz |
|
170 MHz ≤ Δf < min(206 MHz, Δfmax) |
170.05 MHz ≤ f_offset < min(206.05 MHz, f_offsetmax) |
Max(Prated,c – 64.6dB, -40dBm) |
100 kHz |
|
206 MHz ≤ Δf ≤ Δfmax |
206.05 MHz ≤ f_offset < f_offsetmax |
Max(Prated,c – 69.6dB, -40dBm) |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 20 MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be Max(Prated,c – 62.6dB, -40 dBm)/100kHz. |
|||
Table 6.6.3.2D-2: Local Area and Medium Range BS operating band unwanted emission limits in Band 46 for 10MHz channel bandwidth
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 0.5 MHz |
0.05 MHz ≤ f_offset < 0.55 MHz |
|
100 kHz |
|
0.5 MHz ≤ Δf < 5 MHz |
0.55 MHz ≤ f_offset < min(5.05 MHz, f_offsetmax) |
|
100 kHz |
|
5 MHz ≤ Δf < min(10 MHz, Δfmax) |
5.05 MHz ≤ f_offset < min(10.05 MHz, f_offsetmax) |
|
100 kHz |
|
10 MHz ≤ Δf < min(85 MHz, Δfmax) |
10.05 MHz ≤ f_offset < min(85.05 MHz, f_offsetmax) |
Max(Prated,c – 59.5dB, -40dBm) |
100 kHz |
|
85 MHz ≤ Δf < min(103 MHz, Δfmax) |
85.05 MHz ≤ f_offset < min(103.05 MHz, f_offsetmax) |
Max(Prated,c – 61.5dB, -40dBm) |
100 kHz |
|
103 MHz ≤ Δf ≤ Δfmax |
103.05 MHz ≤ f_offset < f_offsetmax |
Max(Prated,c – 66.5dB, -40dBm) |
100 kHz |
|
NOTE 1: For a BS supporting non-contiguous spectrum operation within any operating band, the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap. Exception is f ≥ 10 MHz from both adjacent sub blocks on each side of the sub-block gap, where the minimum requirement within sub-block gaps shall be Max (Prated,c – 59.5dB, -40 dBm)/100kHz. |
|||
6.6.3.2E Minimum requirements for standalone NB-IoT Wide Area BS
For standalone NB-IoT BS, emissions shall not exceed the maximum levels specified in Tables 6.6.3.2E-1.
Table 6.6.3.2E-1: Standalone NB-IoT BS operating band unwanted emission limits
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2, 3, 4, 5) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 0.05 MHz |
0.015 MHz ≤ f_offset < 0.065 MHz |
|
30 kHz |
|
0.05 MHz ≤ Δf < 0.15 MHz |
0.065 MHz ≤ f_offset < 0.165 MHz |
|
30 kHz |
|
0.15 MHz ≤ Δf < 0.2 MHz |
0.165 MHz ≤ f_offset < 0.215 MHz |
-14 dBm |
30 kHz |
|
0.2 MHz ≤ Δf < 1 MHz |
0.215 MHz ≤ f_offset < 1.015 MHz |
|
30 kHz |
|
(Note 9) |
1.015 MHz ≤ f_offset < 1.5 MHz |
-26 dBm |
30 kHz |
|
1 MHz ≤ Δf ≤ min(Δfmax, 10 MHz) |
1.5 MHz ≤ f_offset < min(f_offsetmax, 10.5 MHz) |
-13 dBm |
1 MHz |
|
10 MHz ≤ Δf ≤ Δfmax |
10.5 MHz ≤ f_offset < f_offsetmax |
-15 dBm (Note 10) |
1 MHz |
|
NOTE 1: The limits in this table only apply for operation with a NB-IoT carrier adjacent to the Base Station RF Bandwidth edge. NOTE 2: For a BS supporting non-contiguous spectrum operation within any operating band the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap, where the contribution from the far-end sub-block shall be scaled according to the measurement bandwidth of the near-end sub-block. NOTE 3: For a BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap, where the contribution from the far-end sub-block or RF Bandwidth shall be scaled according to the measurement bandwidth of the near-end sub-block or RF Bandwidth. NOTE 4: In case the carrier adjacent to the RF bandwidth edge is a NB-IoT carrier, the value of X = PNB-IoTcarrier – 43, where PNB-IoTcarrier is the power level of the NB-IoT carrier adjacent to the RF bandwidth edge. In other cases, X = 0. NOTE 5: For BS that only support E-UTRA and NB-IoT multi-carrier operation, the requirements in this table do not apply to an E-UTRA BS from Release 8, which is upgraded to support E-UTRA and NB-IoT multi-carrier operation, where the upgrade does not affect existing RF parts of the radio unit related to the requirements in this table. In this case, the requirements in clauses 6.6.3.1 and 6.6.3.2 shall apply. |
|||
6.6.3.2F Minimum requirements for standalone NB-IoT Local Area BS
For standalone NB-IoT local area BS, emissions shall not exceed the maximum levels specified in Tables 6.6.3.2H-1.
Table 6.6.3.2F-1: Standalone NB-IoT local area BS operating band unwanted emission limits
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2, 3, 4) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 0.05 MHz (Note 1) |
0.015 MHz ≤ f_offset < 0.065 MHz |
|
30 kHz |
|
0.05 MHz ≤ Δf < 0.16 MHz |
0.065 MHz ≤ f_offset < 0.175 MHz |
|
30 kHz |
|
0.15 MHz ≤ Δf < 5 MHz (Note 1) |
0.05 MHz ≤ f_offset < 5.05 MHz |
|
100 kHz |
|
5 MHz ≤ Δf < min(10 MHz, Δfmax) |
5.05 MHz ≤ f_offset < min(10.05 MHz, f_offsetmax) |
-37 dBm |
100 kHz |
|
10 MHz ≤ Δf ≤ Δfmax |
10.05 MHz ≤ f_offset < f_offsetmax |
-37 dBm (Note 10) |
100 kHz |
|
NOTE 1: The limits in this table only apply for operation with a NB-IoT carrier adjacent to the Base Station RF Bandwidth edge. NOTE 2: For BS supporting non-contiguous spectrum operation within any operating band the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap, where the contribution from the far-end sub-block shall be scaled according to the measurement bandwidth of the near-end sub-block. NOTE 3: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap, where the contribution from the far-end sub-block or RF Bandwidth shall be scaled according to the measurement bandwidth of the near-end sub-block or RF Bandwidth. NOTE 4: In case the carrier adjacent to the RF bandwidth edge is a NB-IoT carrier, the value of X = PNB-IoTcarrier – 24, where PNB-IoTcarrier is the power level of the NB-IoT carrier adjacent to the RF bandwidth edge. In other cases, X = 0. |
|||
6.6.3.2G Minimum requirements for standalone NB-IoT Home BS (Category A and B)
For standalone NB-IoT Home BS, emissions shall not exceed the maximum levels specified in Table 6.6.3.2G-1.
Table 6.6.3.2G-1: Standalone NB-IoT Home BS operating band unwanted emission limits (E-UTRA bands ≤3GHz)
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 0.05 MHz |
0.015 MHz ≤ f_offset < 0.065 MHz |
|
30 kHz |
|
0.05 MHz ≤ Δf < 0.16 MHz |
0.065 MHz ≤ f_offset < 0.175 MHz |
|
30 kHz |
|
0.16 MHz ≤ Δf < 5 MHz (Note 8) |
0.175 MHz ≤ f_offset < 5.05 MHz |
|
100 kHz |
|
5 MHz ≤ Δf < min(10 MHz, Δfmax) |
5.05 MHz ≤ f_offset < min(10.05 MHz, f_offsetmax) |
-41 dBm |
100 kHz |
|
10 MHz ≤ Δf ≤ Δfmax |
10.05 MHz ≤ f_offset < f_offsetmax |
-41 dBm (Note 10) |
100 kHz |
|
NOTE 1: The limits in this table only apply for operation with a standalone NB-IoT carrier adjacent to the Base Station RF Bandwidth edge. NOTE 2: In case the carrier adjacent to the RF bandwidth edge is a standalone NB-IoT carrier, the value of X = PNB-IoTcarrier – 20, where PNB-IoTcarrier is the power level of the standalone NB-IoT carrier adjacent to the RF bandwidth edge. In other cases, X = 0. |
|||
6.6.3.2H Minimum requirements for standalone NB-IoT Medium Range BS
For standalone NB-IoT medium range BS (maximum output power 31 < Prated,c ≤ 38 dBm), emissions shall not exceed the maximum levels specified in Tables 6.6.3.2H-1.
Table 6.6.3.2H-1: Standalone NB-IoT medium range BS operating band unwanted emission limits, BS maximum output power 31 < Prated,c ≤ 38 dBm
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2, 3) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 0.05 MHz (Note 1) |
0.015 MHz ≤ f_offset < 0.065 MHz |
|
30 kHz |
|
0.05 MHz ≤ Δf < 0.15 MHz |
0.065 MHz ≤ f_offset < 0.165 MHz |
|
30 kHz |
|
0.15 MHz ≤ Δf < 0.6 MHz (Note 1) |
0.015MHz ≤ f_offset < 0.615MHz |
|
30 kHz |
|
0.6 MHz ≤ Δf < 1 MHz |
0.615MHz ≤ f_offset < 1.015MHz |
|
30 kHz |
|
(Note 6) |
1.015MHz ≤ f_offset < 1.5 MHz |
Prated,c – 65 dB |
30 kHz |
|
1 MHz ≤ Δf ≤ 2.8 MHz |
1.5 MHz ≤ f_offset < 3.3 MHz |
Prated,c – 52 dB |
1 MHz |
|
2.8 MHz ≤ Δf ≤ 5 MHz |
3.3 MHz ≤ f_offset < 5.5 MHz |
min(Prated,c – 52 dB, -15dBm) |
1 MHz |
|
5 MHz ≤ Δf ≤ Δfmax |
5.5 MHz ≤ f_offset < f_offsetmax |
Prated,c – 56 dB |
1 MHz |
|
NOTE 1: The limits in this table only apply for operation with a standalone NB-IoT carrier adjacent to the Base Station RF Bandwidth edge. NOTE 2: For BS supporting non-contiguous spectrum operation within any operating band the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap, where the contribution from the far-end sub-block shall be scaled according to the measurement bandwidth of the near-end sub-block. NOTE 3: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap, where the contribution from the far-end sub-block or RF Bandwidth shall be scaled according to the measurement bandwidth of the near-end sub-block or RF Bandwidth. |
|||
For standalone NB-IoT medium range BS (maximum output power Prated,c ≤ 31 dBm), emissions shall not exceed the maximum levels specified in Tables 6.6.3.2H-2.
Table 6.6.3.2H-2: Standalone NB-IoT medium range BS operating band unwanted emission limits, BS maximum output power Prated,c ≤ 31 dBm
|
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement (Note 1, 2, 3, 4) |
Measurement bandwidth (Note 8) |
|
0 MHz ≤ Δf < 0.05 MHz (Note 1) |
0.015 MHz ≤ f_offset < 0.065 MHz |
|
30 kHz |
|
0.05 MHz ≤ Δf < 0.15 MHz |
0.065 MHz ≤ f_offset < 0.165 MHz |
|
30 kHz |
|
0.15 MHz ≤ Δf < 0.6 MHz (Note 1) |
0.015MHz ≤ f_offset < 0.615MHz |
|
30 kHz |
|
0.6 MHz ≤ Δf < 1 MHz |
0.615MHz ≤ f_offset < 1.015MHz |
|
30 kHz |
|
(Note 6) |
1.015MHz ≤ f_offset < 1.5 MHz |
-34 dBm |
30 kHz |
|
1 MHz ≤ Δf ≤ 5 MHz |
1.5 MHz ≤ f_offset < 5.5 MHz |
-21 dBm |
1 MHz |
|
5 MHz ≤ Δf ≤ Δfmax |
5.5 MHz ≤ f_offset < f_offsetmax |
-25 dBm |
1 MHz |
|
NOTE 1: The limits in this table only apply for operation with a NB-IoT carrier adjacent to the Base Station RF Bandwidth edge. NOTE 2: For BS supporting non-contiguous spectrum operation within any operating band the minimum requirement within sub-block gaps is calculated as a cumulative sum of contributions from adjacent sub blocks on each side of the sub block gap, where the contribution from the far-end sub-block shall be scaled according to the measurement bandwidth of the near-end sub-block. NOTE 3: For BS supporting multi-band operation with Inter RF Bandwidth gap < 20MHz the minimum requirement within the Inter RF Bandwidth gaps is calculated as a cumulative sum of contributions from adjacent sub-blocks or RF Bandwidth on each side of the Inter RF Bandwidth gap, where the contribution from the far-end sub-block or RF Bandwidth shall be scaled according to the measurement bandwidth of the near-end sub-block or RF Bandwidth. NOTE 4: In case the carrier adjacent to the RF bandwidth edge is a NB-IoT carrier, the value of X = PNB-IoTcarrier – 31, where PNB-IoTcarrier is the power level of the NB-IoT carrier adjacent to the RF bandwidth edge. In other cases, X = 0. |
|||
6.6.3.3 Additional requirements
These requirements may be applied for the protection of other systems operating inside or near each supported E-UTRA, E-UTRA with NB-IoT and NB-IoT BS downlink operating band. The limits may apply as an optional protection of such systems that are deployed in the same geographical area as the E-UTRA, E-UTRA with NB-IoT and NB-IoT BS, or they may be set by local or regional regulation as a mandatory requirement for an E-UTRA operating band. It is in some cases not stated in the present document whether a requirement is mandatory or under what exact circumstances that a limit applies, since this is set by local or regional regulation. An overview of regional requirements in the present document is given in clause 4.3.
In certain regions the following requirement may apply. For E-UTRA, E-UTRA with NB-IoT and NB-IoT BS operating in Bands 5, 26, 27 or 28, emissions shall not exceed the maximum levels specified in Tables 6.6.3.3-1.
Table 6.6.3.3-1: Additional operating band unwanted emission limits for E-UTRA bands <1GHz
|
Channel bandwidth |
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement |
Measurement bandwidth (Note 8) |
|
200 kHz |
0 MHz ≤ Δf < 1 MHz |
0.005 MHz ≤ f_offset < 0.995 MHz |
-6 dBm |
10 kHz |
|
1.4 MHz |
0 MHz ≤ Δf < 1 MHz |
0.005 MHz ≤ f_offset < 0.995 MHz |
-14 dBm |
10 kHz |
|
3 MHz |
0 MHz ≤ Δf < 1 MHz |
0.015 MHz ≤ f_offset < 0.985 MHz |
-13 dBm |
30 kHz |
|
5 MHz |
0 MHz ≤ Δf < 1 MHz |
0.015 MHz ≤ f_offset < 0.985 MHz |
-15 dBm |
30 kHz |
|
10 MHz |
0 MHz ≤ Δf < 1 MHz |
0.05 MHz ≤ f_offset < 0.95 MHz |
-13 dBm |
100 kHz |
|
15 MHz |
0 MHz ≤ Δf < 1 MHz |
0.05 MHz ≤ f_offset < 0.95 MHz |
-13 dBm |
100 kHz |
|
20 MHz |
0 MHz ≤ Δf < 1 MHz |
0.05 MHz ≤ f_offset < 0.95 MHz |
-13 dBm |
100 kHz |
|
All |
1 MHz ≤ Δf < Δfmax |
1.05 MHz ≤ f_offset < f_offsetmax |
-13 dBm |
100 kHz |
In certain regions the following requirement may apply. For E-UTRA, E-UTRA with NB-IoT and NB-IoT BS operating in Bands 2, 4, 10, 23, 25, 30, 35, 36, 41, 66, 70, emissions shall not exceed the maximum levels specified in Table 6.6.3.3-2.
Table 6.6.3.3-2: Additional operating band unwanted emission limits for E-UTRA bands>1GHz
|
Channel bandwidth |
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement |
Measurement bandwidth (Note 8) |
|
200 kHz |
0 MHz ≤ Δf < 1 MHz |
0.005 MHz ≤ f_offset < 0.995 MHz |
-6 dBm |
10 kHz |
|
1.4 MHz |
0 MHz ≤ Δf < 1 MHz |
0.005 MHz ≤ f_offset < 0.995 MHz |
-14 dBm |
10 kHz |
|
3 MHz |
0 MHz ≤ Δf < 1 MHz |
0.015 MHz ≤ f_offset < 0.985 MHz |
-13 dBm |
30 kHz |
|
5 MHz |
0 MHz ≤ Δf < 1 MHz |
0.015 MHz ≤ f_offset < 0.985 MHz |
-15 dBm |
30 kHz |
|
10 MHz |
0 MHz ≤ Δf < 1 MHz |
0.05 MHz ≤ f_offset < 0.95 MHz |
-13 dBm |
100 kHz |
|
15 MHz |
0 MHz ≤ Δf < 1 MHz |
0.05 MHz ≤ f_offset < 0.95 MHz |
-15 dBm |
100 kHz |
|
20 MHz |
0 MHz ≤ Δf < 1 MHz |
0.05 MHz ≤ f_offset < 0.95 MHz |
-16 dBm |
100 kHz |
|
All |
1 MHz ≤ Δf < Δfmax |
1.5 MHz ≤ f_offset < f_offsetmax |
-13 dBm |
1 MHz |
In certain regions the following requirement may apply. For E-UTRA, E-UTRA with NB-IoT and NB-IoT BS operating in Bands 12, 13, 14, 17, 29, 71, 85, 103 emissions shall not exceed the maximum levels specified in Table 6.6.3.3-3.
Table 6.6.3.3-3: Additional operating band unwanted emission limits for E-UTRA (bands 12, 13, 14, 17, 29, 71, 85 and 103)
|
Channel bandwidth |
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement |
Measurement bandwidth (Note 8) |
|
All |
0 MHz ≤ Δf < 100 kHz |
0.015 MHz ≤ f_offset < 0.085 MHz |
-13 dBm |
30 kHz |
|
All |
100 kHz ≤ Δf < Δfmax |
150 kHz ≤ f_offset < f_offsetmax |
-13 dBm |
100 kHz |
In certain regions, the following requirements may apply to an E-UTRA, E-UTRA with NB-IoT and NB-IoT TDD BS operating in the same geographic area and in the same operating band as another E-UTRA TDD system without synchronisation. For this case the emissions shall not exceed -52 dBm/MHz in each supported downlink operating band except in:
– The frequency range from 10 MHz below the lower channel edge to the frequency 10 MHz above the upper channel edge of each supported band.
In certain regions the following requirement may apply for protection of DTT. For E-UTRA BS operating in Band 20, the level of emissions in the band 470-790 MHz, measured in an 8MHz filter bandwidth on centre frequencies Ffilter according to Table 6.6.3.3-4, shall not exceed the maximum emission level PEM,N declared by the manufacturer. This requirement applies in the frequency range 470-790 MHz even though part of the range falls in the spurious domain.
Table 6.6.3.3-4: Declared emissions levels for protection of DTT
|
Filter centre frequency, Ffilter |
Measurement bandwidth |
Declared emission level [dBm] |
|
Ffilter = 8*N + 306 (MHz); |
8 MHz |
PEM,N |
Note: The regional requirement is defined in terms of EIRP (effective isotropic radiated power), which is dependent on both the BS emissions at the antenna connector and the deployment (including antenna gain and feeder loss). The requirement defined above provides the characteristics of the base station needed to verify compliance with the regional requirement. Compliance with the regional requirement can be determined using the method outlined in Annex G.
Table 6.6.3.3-5: Void
In regions where FCC regulation applies, requirements for protection of GPS according to FCC Order DA 20-48 applies for operation in Band 24. The following normative requirement covers the base station, to be used together with other information about the site installation to verify compliance with the requirement in FCC Order DA 20-48. The requirement applies to BS operating in Band 24 to ensure that appropriate interference protection is provided to the 1541 – 1650 MHz band. This requirement applies to the frequency range 1541-1650 MHz, even though part of this range falls within the spurious domain.
The level of emissions in the 1541 – 1650 MHz band, measured in measurement bandwidth according to Table 6.6.3.3-6 shall not exceed the maximum emission levels PEM,B24,a, PEM,B24,b, PEM,B24,c, PEM,B24,d, PEM,B24,e and PEM,B24,f declared by the manufacturer.
Table 6.6.3.3-6: Declared emissions levels for protection of the 1541-1650 MHz band
|
Operating Band |
Frequency range |
Declared emission level [dBW] (Measurement bandwidth = 1 MHz) |
Declared emission level [dBW] of discrete emissions of less than 700 Hz bandwidth (Measurement bandwidth = 1 kHz) |
Declared emission level (dBW) of discrete emissions of less than 2 kHz bandwidth (Measurement bandwidth = 1 kHz) |
|
24 |
1541 – 1559 MHz |
PEM,B24,a |
PEM,B24,f |
|
|
1559 – 1610 MHz |
PEM,B24,b |
PEM,B24,d |
||
|
1610 – 1650 MHz |
PEM,B24,c |
PEM,B24,e |
Note: The regional requirements in FCC Order DA 20-48 are defined in terms of EIRP (effective isotropic radiated power), which is dependent on both the BS emissions at the antenna connector and the deployment (including antenna gain and feeder loss). The EIRP level is calculated using: PEIRP = PE + Gant where PE denotes the BS unwanted emission level at the antenna connector, Gant equals the BS antenna gain minus feeder loss. The requirement defined above provides the characteristics of the base station needed to verify compliance with the regional requirement.
Table 6.6.3.3-7: Void
In certain regions, the following requirements may apply to E-UTRA BS operating in Band 32 within 1452-1492 MHz, in Band 75 within 1432-1517 MHz and in Band 76 within 1427-1432 MHz. The level of operating band unwanted emissions, measured on centre frequencies f_offset with filter bandwidth, according to Table 6.6.3.3-8, shall neither exceed the maximum emission level PEM,B32,B75,B76,a , PEM,B32,B75,B76,b nor PEM,B32,B75,B76,c declared by the manufacturer.
For Band 32, this requirement applies in the frequency range 1452-1492 MHz when non-Mobile/Fixed Communications Network (MFCN) services are deployed in adjacent frequency ranges, while it applies also within 1427-1452 MHz and/or 1492-1517 MHz when MFCN services are deployed in such frequency ranges, even though part of the ranges falls in the spurious domain. For Band 75, this requirement applies in the frequency range 1427-1517 MHz. For Band 76, this requirement applies in the frequency range 1432-1517 MHz even though part of the range falls in the spurious domain.
Table 6.6.3.3-8: Declared operating band 32, 75 and 76 unwanted emission within 1427-1517 MHz
|
Frequency offset of measurement filter centre frequency, f_offset |
Declared emission level [dBm] |
Measurement bandwidth |
|
2.5 MHz |
PEM,B32,B75,B76,a |
5 MHz |
|
7.5 MHz |
PEM,B32,B75,B76,b |
5 MHz |
|
12.5 MHz ≤ f_offset ≤ f_offsetmax |
PEM,B32,B75,B76,c |
5 MHz |
|
NOTE: For Band 32, when non-MFCN services are deployed in the adjacent bands, f_offsetmax denotes the frequency difference between the lower channel edge and 1454.5 MHz, and the frequency difference between the upper channel edge and 1489.5 MHz for the set channel position. For Band 32, when MFCN services are deployed in the adjacent frequencies, Band 75 and Band 76, f_offsetmax denotes the frequency difference between the lower channel edge and 1429.5 MHz, and the frequency difference between the upper channel edge and 1514.5 MHz for the set channel position. |
||
NOTE: The regional requirement, included in [19], is defined in terms of EIRP per antenna, which is dependent on both the BS emissions at the antenna connector and the deployment (including antenna gain and feeder loss). The requirement defined above provides the characteristics of the base station needed to verify compliance with the regional requirement. The assessment of the EIRP level is described in Annex H.
In certain regions, the following requirement may apply to E-UTRA BS operating in Band 32 within 1452-1492 MHz for the protection of non-MFCN services in spectrum adjacent to the frequency range 1452-1492 MHz. The level of emissions, measured on centre frequencies Ffilter with filter bandwidth according to Table 6.6.3.3-9, shall neither exceed the maximum emission level PEM,B32,d nor PEM,B32,e declared by the manufacturer. This requirement applies in the frequency range 1429-1518MHz even though part of the range falls in the spurious domain.
Table 6.6.3.3-9: Operating band 32 declared emission outside 1452-1492 MHz
|
Filter centre frequency, Ffilter |
Declared emission level [dBm] |
Measurement bandwidth |
|
1429.5 MHz ≤ Ffilter ≤ 1448.5 MHz |
PEM,B32,d |
1 MHz |
|
Ffilter = 1450.5 MHz |
PEM,B32,e |
3 MHz |
|
Ffilter = 1493.5 MHz |
PEM,B32,e |
3 MHz |
|
1495.5 MHz ≤ Ffilter ≤ 1517.5 MHz |
PEM,B32,d |
1 MHz |
NOTE: The regional requirement, included in [16], is defined in terms of EIRP, which is dependent on both the BS emissions at the antenna connector and the deployment (including antenna gain and feeder loss). The requirement defined above provides the characteristics of the base station needed to verify compliance with the regional requirement. The assessment of the EIRP level is described in Annex H.
In certain regions, the following requirement may apply to BS operating in Band 50 and Band 75 within 1492-1517 MHz and in Band 74 within 1492-1518 MHz. The level of emissions, measured on centre frequencies Ffilter with filter bandwidth according to Table 6.6.3.3-9A, shall neither exceed the maximum emission level PEM,B50,B74,B75,a nor PEM,B50,B74,B75,b declared by the manufacturer.
Table 6.6.3.3-9A: Operating band 50, 74 and 75 declared emission above 1518 MHz
|
Filter centre frequency, Ffilter |
Declared emission level [dBm] |
Measurement bandwidth |
|
1518.5 MHz ≤ Ffilter ≤ 1519.5 MHz |
PEM,B50,B74,B75,a |
1 MHz |
|
1520.5 MHz ≤ Ffilter ≤ 1558.5 MHz |
PEM,B50,B74,B75,b |
1 MHz |
NOTE: The regional requirement, included in [19], is defined in terms of EIRP, which is dependent on both the BS emissions at the antenna connector and the deployment (including antenna gain and feeder loss). The requirement defined above provides the characteristics of the base station needed to verify compliance with the regional requirement. The assessment of the EIRP level is described in Annex H.
In certain regions, the following requirement may apply to E-UTRA BS operating in Band 50 and Band 75 within 1432-1452 MHz, and in Band 51 and Band 76. Emissions shall not exceed the maximum levels specified in Table 6.6.3.3-9B.
Table 6.6.3.3-9B: Additional operating band unwanted emission limits for BS operating in Band 50 and 75 within 1432-1452 MHz, and in Band 51 and 76
|
Filter centre frequency, Ffilter |
Maximum Level [dBm] |
Measurement Bandwidth |
|
Ffilter = 1413.5 MHz |
-42 |
27 MHz |
In addition for Band 46 operation, the BS may have to comply with the applicable operating band unwanted emission limits established regionally, when deployed in regions where those limits apply and under the conditions declared by the manufacturer. The regional requirements may be in the form of conducted power, power spectral density, EIRP and other types of limits. In case of regulatory limits based on EIRP, assessment of the EIRP level is described in Annex H.
In certain regions the following requirement may apply to E-UTRA BS operating in Band 45. Emissions shall not exceed the maximum levels specified in Table 6.6.3.3-10.
Table 6.6.3.3-10: Emissions limits for protection of adjacent band services
|
Operating Band |
Filter centre frequency, Ffilter |
Maximum Level [dBm] |
Measurement Bandwidth |
|
45 |
Ffilter = 1467.5 |
-20 |
1 MHz |
|
Ffilter = 1468.5 |
-23 |
1 MHz |
|
|
Ffilter = 1469.5 |
-26 |
1 MHz |
|
|
Ffilter = 1470.5 |
-33 |
1 MHz |
|
|
Ffilter = 1471.5 |
-40 |
1 MHz |
|
|
1472.5 MHz ≤ Ffilter ≤ 1491.5 MHz |
-47 |
1 MHz |
The following requirement may apply to E-UTRA BS operating in Band 48 and Band 49 in certain regions. Emissions shall not exceed the maximum levels specified in Table 6.6.3.3-11.
Table 6.6.3.3-11: Additional operating band unwanted emission limits for Band 48 and Band 49
|
Channel bandwidth |
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement |
Measurement bandwidth (Note 8) |
|
All |
0 MHz ≤ Δf < 10 MHz |
0.5 MHz ≤ f_offset < 9.5 MHz |
-13 dBm |
1 MHz |
The following requirement may apply to E-UTRA BS operating in Band 53 in certain regions. Emissions shall not exceed the maximum levels specified in Table 6.6.3.3-12.
Table 6.6.3.3-12: Additional operating band unwanted emission limits for Band 53
|
Channel bandwidth [MHz] |
Frequency range [MHz] |
Frequency offset of measurement filter ‑3dB point, Δf |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement |
Measurement bandwidth (Note 8) |
|
1.4, 3, 5 |
2400 – 2477.5 |
6 MHz ≤ Δf < 83.5 MHz |
6.5 MHz ≤ f_offset < 83 MHz |
-25 dBm |
1 MHz |
|
10 |
2400 – 2473.5 |
10 MHz ≤ Δf < 83.5 MHz |
10.5 MHz ≤ f_offset < 83 MHz |
-25 dBm |
1 MHz |
|
1.4, 3, 5 |
2477.5 – 2478.5 |
5 MHz ≤ Δf < 6 MHz |
5.5 MHz |
-13 dBm |
1 MHz |
|
10 |
2473.5 – 2478.5 |
5 MHz ≤ Δf < 10 MHz |
5.5 MHz ≤ f_offset < 9.5 MHz |
-13 dBm |
1 MHz |
|
All |
2478.5 – 2483.5 |
0 MHz ≤ Δf < 5 MHz |
0.5 MHz ≤ f_offset < 4.5 MHz |
-10 dBm |
1 MHz |
|
1.4, 3, 5 |
2495 – 2501 |
0 MHz ≤ Δf < 6 MHz |
0.5 MHz ≤ f_offset < 5.5 MHz |
-13 dBm |
1 MHz |
|
10 |
2495 – 2505 |
0 MHz ≤ Δf < 10 MHz |
0.5 MHz ≤ f_offset < 9.5 MHz |
-13 dBm |
1 MHz |
|
1.4, 3, 5 |
2501 – 2690 |
6 MHz ≤ Δf < 195 MHz |
6.5 MHz ≤ f_offset < 194.5 MHz |
-25 dBm |
1 MHz |
|
10 |
2505 – 2690 |
10 MHz ≤ Δf < 195 MHz |
10.5 MHz ≤ f_offset < 194.5 MHz |
-25 dBm |
1 MHz |
The following notes are common to all clauses in 6.6.3:
NOTE 6: Local or regional regulations may specify another excluded frequency range, which may include frequencies where synchronised E-UTRA TDD systems operate.
NOTE 7: E-UTRA TDD base stations that are synchronized can transmit without these additional co-existence requirements.
NOTE 8: As a general rule for the requirements in clause 6.6.3, the resolution bandwidth of the measuring equipment should be equal to the measurement bandwidth. However, to improve measurement accuracy, sensitivity and efficiency, the resolution bandwidth may be smaller than the measurement bandwidth. When the resolution bandwidth is smaller than the measurement bandwidth, the result should be integrated over the measurement bandwidth in order to obtain the equivalent noise bandwidth of the measurement bandwidth.
NOTE 9: This frequency range ensures that the range of values of f_offset is continuous.
NOTE 10: The requirement is not applicable when Δfmax < 10 MHz.
NOTE 11: For Home BS, the parameter P is defined as the aggregated maximum output power of all transmit antenna connectors of Home BS.