G.2 Typical receiver sensitivity performance (QPSK)

36.1013GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Release 18TSUser Equipment (UE) radio transmission and reception

The residual BLER after HARQ shall be lower than 1% for the reference measurement channels as specified in Annexes G.3 (with one sided dynamic OCNG Pattern OP.1 FDD/TDD for the DL-signal as described in Annex A.5.1.1/A.5.2.1) with parameters specified in Table G.2-1 and Table G.2-2

Table G.2-1: Reference sensitivity QPSK PSENS

Channel bandwidth

E-UTRA Band

1.4 MHz

(dBm)

3 MHz

(dBm)

5 MHz

(dBm)

10 MHz

(dBm)

15 MHz

(dBm)

20 MHz

(dBm)

Duplex Mode

1

[-102]

FDD

2

TBD

FDD

3

TBD

FDD

4

TBD

FDD

5

TBD

FDD

6

TBD

FDD

7

TBD

FDD

8

TBD

FDD

9

TBD

FDD

10

TBD

FDD

11

TBD

FDD

12

TBD

FDD

13

TBD

FDD

14

TBD

FDD

…

17

TBD

FDD

18

TBD

FDD

19

TBD

FDD

20

TBD

FDD

21

TBD

FDD

22

TBD

FDD

23

TBD

FDD

24

TBD

FDD

26

TBD

FDD

27

TBD

FDD

28

TBD

FDD

30

TBD

FDD

31

TBD

FDD

…

33

[-102]

TDD

34

[-102]

TDD

35

[-102]

TDD

36

[-102]

TDD

37

[-102]

TDD

38

[-102]

TDD

39

[-102]

TDD

40

[-102]

TDD

42

[-102]

TDD

43

[-102]

TDD

44

[-102]

TDD

45

[-102]

TDD

…

54

TBD

TDD

…

65

TBD

FDD

70

TBD

FDD

71

TBD

FDD

87

TBD

FDD

88

TBD

FDD

Note 1: The transmitter shall be set to PUMAX as defined in clause 6.2.5

Note 2: Reference measurement channel is G.3 with one sided dynamic OCNG Pattern OP.1 FDD/TDD as described in Annex A.5.1.1/A.5.2.1

Note 3: The signal power is specified per port

Note 4: For the UE which supports both Band 3 and Band 9 the reference sensitivity level is FFS.

Note 5: For the UE which supports both Band 11 and Band 21 the reference sensitivity level is FFS.

Table G.2-2 specifies the minimum number of allocated uplink resource blocks for which the reference receive sensitivity requirement in lower SNR must be met.

Table G.2-2: Minimum uplink configuration for reference sensitivity

E-UTRA Band / Channel bandwidth / NRB / Duplex mode

E-UTRA Band

1.4 MHz

3 MHz

5 MHz

10 MHz

15 MHz

20 MHz

Duplex Mode

1

[6]1

FDD

2

[6]1

FDD

3

[6]1

FDD

4

[6]1

FDD

5

[6]1

FDD

6

[6]1

FDD

7

[6]1

FDD

8

[6]1

FDD

9

[6]1

FDD

10

[6]1

FDD

11

[6]1

FDD

12

[6]1

FDD

13

[6]1

FDD

14

[6]1

FDD

…

17

[6]1

FDD

18

[6]1

FDD

19

[6]1

FDD

20

[6]1

FDD

22

[6]1

FDD

21

[6]1

FDD

23

[6]1

FDD

24

[6]1

FDD

26

[6]1

FDD

27

[6]1

FDD

28

[6]1

FDD

30

[6]1

FDD

31

[5]4

FDD

…

33

50

TDD

34

50

TDD

35

50

TDD

36

50

TDD

37

50

TDD

38

50

TDD

39

50

TDD

40

50

TDD

42

50

TDD

43

50

TDD

44

50

TDD

45

50

TDD

…

54

[6]

TDD

…

65

[6]1

FDD

…

70

[6]1

FDD

71

[6]1

FDD

87

[5]4

FDD

88

[5]4

FDD

Note 1: The UL resource blocks shall be located as close as possible to the downlink operating band but confined within the transmission bandwidth configuration for the channel bandwidth (Table 5.6-1).

Note 2: For the UE which supports both Band 11 and Band 21 the minimum uplink configuration for reference sensitivity is FFS.

Note 3: For Band 20; in the case of 15MHz channel bandwidth, the UL resource blocks shall be located at RBstart _11 and in the case of 20MHz channel bandwidth, the UL resource blocks shall be located at RBstart _16

Note 4: For Band 31, 87, 88; in the case of 5MHz channel bandwidth, the UL resource blocks shall be located at RBstart _10

Unless given by Table G.2-3, the minimum requirements specified in Tables G.2-1 and G.2-2 shall be verified with the network signalling value NS_01 (Table 6.2.4-1) configured.

Table G.2-3: Network Signalling Value for reference sensitivity

Network Signalling value

E-UTRA Band

NS_03

2, 4, 10, 23, 35, 36, 70

NS_06

12,13,14,17

NS_08

19

NS_09

21

NS_21

30

NS_35

71

NS_56

24

NS_62

54