A.3.3 Reference measurement channels for PDSCH performance requirements (FDD)
36.1013GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Release 18TSUser Equipment (UE) radio transmission and reception
A.3.3.1 Single-antenna transmission (Common Reference Symbols)
Table A.3.3.1-1: Fixed Reference Channel QPSK R=1/3
Parameter |
Unit |
Value |
|||||
Reference channel |
R.4 FDD |
R.42 FDD |
R.42-1 FDD |
R.42-2 FDD |
R.42-3 FDD |
R.2 FDD |
|
Channel bandwidth |
MHz |
1.4 |
20 |
3 |
5 |
15 |
10 |
Allocated resource blocks (Note 4) |
6 |
100 |
15 |
25 |
75 |
50 |
|
Allocated subframes per Radio Frame |
9 |
9 |
9 |
9 |
9 |
9 |
|
Modulation |
QPSK |
QPSK |
QPSK |
QPSK |
QPSK |
QPSK |
|
Target Coding Rate |
1/3 |
1/3 |
1/3 |
1/3 |
1/3 |
1/3 |
|
Information Bit Payload (Note 4) |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
408 |
8760 |
1320 |
2216 |
6712 |
4392 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
152 |
8760 |
1064 |
1800 |
6712 |
4392 |
Number of Code Blocks |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
1 |
2 |
1 |
1 |
2 |
1 |
|
For Sub-Frame 5 |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
|
For Sub-Frame 0 |
1 |
2 |
1 |
1 |
2 |
1 |
|
Binary Channel Bits (Note 4) |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
1368 |
27600 |
3780 |
6300 |
20700 |
13800 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
528 |
26760 |
2940 |
5460 |
19860 |
12960 |
Max. Throughput averaged over 1 frame (Note 4) |
Mbps |
0.342 |
7.884 |
1.162 |
1.953 |
6.041 |
3.953 |
UE Category |
≥ 1 |
≥ 1 |
≥ 1 |
≥ 1 |
≥ 1 |
≥ 1 |
|
Note 1: 2 symbols allocated to PDCCH for 20 MHz, 15 MHz and 10 MHz channel BW; 3 symbols allocated to PDCCH for 5 MHz and 3 MHz; 4 symbols allocated to PDCCH for 1.4 MHz. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). Note 4: Given per component carrier per codeword. |
Table A.3.3.1-2: Fixed Reference Channel 16QAM R=1/2
Parameter |
Unit |
Value |
|||||
Reference channel |
R.3-1 FDD |
R.3 FDD |
|||||
Channel bandwidth |
MHz |
1.4 |
3 |
5 |
10 |
15 |
20 |
Allocated resource blocks |
25 |
50 |
|||||
Allocated subframes per Radio Frame |
9 |
9 |
|||||
Modulation |
16QAM |
16QAM |
|||||
Target Coding Rate |
1/2 |
1/2 |
|||||
Information Bit Payload |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
6456 |
14112 |
||||
For Sub-Frame 5 |
Bits |
N/A |
N/A |
||||
For Sub-Frame 0 |
Bits |
5736 |
12960 |
||||
Number of Code Blocks per Sub-Frame |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
2 |
3 |
|||||
For Sub-Frame 5 |
N/A |
N/A |
|||||
For Sub-Frame 0 |
1 |
3 |
|||||
Binary Channel Bits Per Sub-Frame |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
12600 |
27600 |
||||
For Sub-Frame 5 |
Bits |
N/A |
N/A |
||||
For Sub-Frame 0 |
Bits |
10920 |
25920 |
||||
Max. Throughput averaged over 1 frame |
Mbps |
5.738 |
12.586 |
||||
UE Category |
≥ 1 |
≥ 2 |
|||||
Note 1: 2 symbols allocated to PDCCH for 20 MHz, 15 MHz and 10 MHz channel BW; 3 symbols allocated to PDCCH for 5 MHz and 3 MHz; 4 symbols allocated to PDCCH for 1.4 MHz. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). |
Table A.3.3.1-3: Fixed Reference Channel 64QAM R=3/4
Parameter |
Unit |
Value |
|||||
Reference channel |
R.5 FDD |
R.6 FDD |
R.7 FDD |
R.8 FDD |
R.9 FDD |
||
Channel bandwidth |
MHz |
1.4 |
3 |
5 |
10 |
15 |
20 |
Allocated resource blocks |
15 |
25 |
50 |
75 |
100 |
||
Allocated subframes per Radio Frame |
9 |
9 |
9 |
9 |
9 |
||
Modulation |
64QAM |
64QAM |
64QAM |
64QAM |
64QAM |
64QAM |
|
Target Coding Rate |
3/4 |
3/4 |
3/4 |
3/4 |
3/4 |
3/4 |
|
Information Bit Payload |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
8504 |
14112 |
30576 |
46888 |
61664 |
|
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
|
For Sub-Frame 0 |
Bits |
6456 |
12576 |
28336 |
45352 |
61664 |
|
Number of Code Blocks per Sub-Frame |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
2 |
3 |
5 |
8 |
11 |
||
For Sub-Frame 5 |
N/A |
N/A |
N/A |
N/A |
N/A |
||
For Sub-Frame 0 |
2 |
3 |
5 |
8 |
11 |
||
Binary Channel Bits Per Sub-Frame |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
11340 |
18900 |
41400 |
62100 |
82800 |
|
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
|
For Sub-Frame 0 |
Bits |
8820 |
16380 |
38880 |
59580 |
80280 |
|
Max. Throughput averaged over 1 frame |
Mbps |
7.449 |
12.547 |
27.294 |
42.046 |
55.498 |
|
UE Category |
≥ 1 |
≥ 2 |
≥ 2 |
≥ 2 |
≥ 3 |
||
Note 1: 2 symbols allocated to PDCCH for 20 MHz, 15 MHz and 10 MHz channel BW; 3 symbols allocated to PDCCH for 5 MHz and 3 MHz; 4 symbols allocated to PDCCH for 1.4 MHz. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). |
Table A.3.3.1-3a: Fixed Reference Channel 64QAM R=3/4
Parameter |
Unit |
Value |
|||||
Reference channel |
R.6-1 FDD |
R.7-1 FDD |
R.8-1 FDD |
R.9-1 FDD |
R.9-2 FDD |
||
Channel bandwidth |
MHz |
5 |
10 |
15 |
20 |
20 |
|
Allocated resource blocks (Note 3) |
18 |
17 |
17 |
17 |
83 |
||
Allocated subframes per Radio Frame |
9 |
9 |
9 |
9 |
9 |
||
Modulation |
64QAM |
64QAM |
64QAM |
64QAM |
64QAM |
||
Target Coding Rate |
3/4 |
3/4 |
3/4 |
3/4 |
3/4 |
||
Information Bit Payload |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
10296 |
10296 |
10296 |
10296 |
51024 |
|
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
|
For Sub-Frame 0 |
Bits |
8248 |
10296 |
10296 |
10296 |
51024 |
|
Number of Code Blocks per Sub-Frame |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
2 |
2 |
2 |
2 |
9 |
||
For Sub-Frame 5 |
N/A |
N/A |
N/A |
N/A |
N/A |
||
For Sub-Frame 0 |
2 |
2 |
2 |
2 |
9 |
||
Binary Channel Bits Per Sub-Frame |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
13608 |
14076 |
14076 |
14076 |
68724 |
|
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
|
For Sub-Frame 0 |
Bits |
11088 |
14076 |
14076 |
14076 |
66204 |
|
Max. Throughput averaged over 1 frame |
Mbps |
9.062 |
9.266 |
9.266 |
9.266 |
45.922 |
|
UE Category |
≥ 1 |
≥ 1 |
≥ 1 |
≥ 1 |
≥ 2 |
||
Note 1: 2 symbols allocated to PDCCH for 20 MHz, 15 MHz and 10 MHz channel BW; 3 symbols allocated to PDCCH for 5 MHz and 3 MHz; 4 symbols allocated to PDCCH for 1.4 MHz. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: Localized allocation started from RB #0 is applied. Note 4: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). |
Table A.3.3.1-4: Fixed Reference Channel Single PRB (Channel Edge)
Parameter |
Unit |
Value |
|||||
Reference channel |
R.0 FDD |
R.1 FDD |
|||||
Channel bandwidth |
MHz |
1.4 |
3 |
5 |
10/20 |
15 |
20 |
Allocated resource blocks |
1 |
1 |
|||||
Allocated subframes per Radio Frame |
9 |
9 |
|||||
Modulation |
16QAM |
16QAM |
|||||
Target Coding Rate |
1/2 |
1/2 |
|||||
Information Bit Payload |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
224 |
256 |
||||
For Sub-Frame 5 |
Bits |
N/A |
N/A |
||||
For Sub-Frame 0 |
Bits |
224 |
256 |
||||
Number of Code Blocks per Sub-Frame |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
1 |
1 |
|||||
For Sub-Frame 5 |
N/A |
N/A |
|||||
For Sub-Frame 0 |
1 |
1 |
|||||
Binary Channel Bits Per Sub-Frame |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
504 |
552 |
||||
For Sub-Frame 5 |
Bits |
N/A |
N/A |
||||
For Sub-Frame 0 |
Bits |
504 |
552 |
||||
Max. Throughput averaged over 1 frame |
Mbps |
0.202 |
0.230 |
||||
UE Category |
≥ 1 |
≥ 1 |
|||||
Note 1: 2 symbols allocated to PDCCH for 20 MHz, 15 MHz and 10 MHz channel BW; 3 symbols allocated to PDCCH for 5 MHz and 3 MHz; 4 symbols allocated to PDCCH for 1.4 MHz. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). |
Table A.3.3.1-5: Fixed Reference Channel Single PRB (MBSFN Configuration)
Parameter |
Unit |
Value |
|
Reference channel |
R.29 FDD (MBSFN) |
R.29-1 FDD (MBSFN) |
|
Channel bandwidth |
MHz |
10 |
10 |
Allocated resource blocks |
1 |
1 |
|
MBSFN Configuration |
111111(Note 4) |
11111111(Note 5) |
|
Allocated subframes per Radio Frame |
3 |
3 |
|
Modulation |
16QAM |
16QAM |
|
Target Coding Rate |
1/2 |
1/2 |
|
Information Bit Payload |
|||
For Sub-Frames 4,9 |
Bits |
256 |
0(MBSFN) |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
256 |
256 |
For Sub-Frame 1,2,3,6,7,8 |
Bits |
0 (MBSFN) |
0 (MBSFN) |
Number of Code Blocks per Sub-Frame |
|||
For Sub-Frames 4,9 |
1 |
0(MBSFN) |
|
For Sub-Frame 5 |
N/A |
N/A |
|
For Sub-Frame 0 |
1 |
1 |
|
For Sub-Frame 1,2,3,6,7,8 |
0 (MBSFN) |
0 (MBSFN) |
|
Binary Channel Bits Per Sub-Frame |
|||
For Sub-Frames 4,9 |
Bits |
552 |
0(MBSFN) |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
552 |
552 |
For Sub-Frame 1,2,3,6,7,8 |
Bits |
0 (MBSFN) |
0 (MBSFN) |
Max. Throughput averaged over 1 frame |
kbps |
76.8 |
25.6 |
UE Category |
≥ 1 |
≥ 1 |
|
Note 1: 2 symbols allocated to PDCCH. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). Note 4: MBSFN Subframe Allocation as defined in TS 36.331 [7], one frame with 6 bits is chosen for MBSFN subframe allocation Note 5: MBSFN Subframe Allocation as defined in TS 36.331 [7], one frame with 6 bits and MBSFN Subframe Allocation-v14xy in TS 36.331 [7], one frame with 2 bits, are chosen for MBSFN subframe allocation. |
Table A.3.3.1-6: Fixed Reference Channel QPSK R=1/10
Parameter |
Unit |
Value |
|||||
Reference channel |
R.41 FDD |
||||||
Channel bandwidth |
MHz |
1.4 |
3 |
5 |
10 |
15 |
20 |
Allocated resource blocks |
50 |
||||||
Allocated subframes per Radio Frame |
9 |
||||||
Modulation |
QPSK |
||||||
Target Coding Rate |
1/10 |
||||||
Information Bit Payload |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
1384 |
|||||
For Sub-Frame 5 |
Bits |
N/A |
|||||
For Sub-Frame 0 |
Bits |
1384 |
|||||
Number of Code Blocks per Sub-Frame |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
1 |
||||||
For Sub-Frame 5 |
N/A |
||||||
For Sub-Frame 0 |
1 |
||||||
Binary Channel Bits Per Sub-Frame |
|||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
13800 |
|||||
For Sub-Frame 5 |
Bits |
N/A |
|||||
For Sub-Frame 0 |
Bits |
12960 |
|||||
Max. Throughput averaged over 1 frame |
Mbps |
1.246 |
|||||
UE Category |
≥ 1 |
||||||
Note 1: 2 symbols allocated to PDCCH for 20 MHz, 15 MHz and 10 MHz channel BW; 3 symbols allocated to PDCCH for 5 MHz and 3 MHz; 4 symbols allocated to PDCCH for 1.4 MHz. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). |
Table A.3.3.1-7: Fixed Reference Channel for CA demodulation with power imbalance
Parameter |
Unit |
Value |
||
Reference channel |
R.49 FDD |
R.49-1 FDD |
R.49-2 FDD |
|
Channel bandwidth |
MHz |
20 |
10 |
5 |
Allocated resource blocks |
100 |
50 |
25 |
|
Allocated subframes per Radio Frame |
9 |
9 |
9 |
|
Modulation |
64QAM |
64QAM |
64QAM |
|
Coding Rate |
||||
For Sub-Frame 1,2,3,4,6,7,8,9, |
0.84 |
0.84 |
0.84 |
|
For Sub-Frame 5 |
N/A |
N/A |
N/A |
|
For Sub-Frame 0 |
0.87 |
0.87 |
0.86 |
|
Information Bit Payload |
||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
63776 |
31704 |
15840 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
For Sub-Frame 0 |
63776 |
30576 |
14112 |
|
Number of Code Blocks per Sub-Frame |
||||
For Sub-Frames 0,1,2,3,4,6,7,8,9 |
Code Blocks |
11 |
6 |
3 |
For Sub-Frame 5 |
Code Blocks |
N/A |
N/A |
N/A |
Binary Channel Bits Per Sub-Frame |
5 |
3 |
||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
75600 |
||
For Sub-Frame 5 |
Bits |
N/A |
37800 |
18900 |
For Sub-Frame 0 |
Bits |
73080 |
N/A |
N/A |
Max. Throughput averaged over 1 frame |
Mbps |
57.398 |
35280 |
16380 |
UE Category |
≥5 |
≥2 |
≥2 |
|
Note 1: 3 symbols allocated to PDCCH. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). |
A.3.3.2 Multi-antenna transmission (Common Reference Symbols)
A.3.3.2.1 Two antenna ports
Table A.3.3.2.1-1: Fixed Reference Channel two antenna ports
Parameter |
Unit |
Value |
|||||||||||
Reference channel |
R.10 FDD |
R.11 FDD |
R.11-1 FDD |
R.11-2 FDD |
R.11-3 FDD Note 5 |
R.11-4 FDD |
R.30 FDD |
R.30-1 FDD |
R.35-1 FDD |
R.35 FDD |
R.35-2 FDD |
R.35-3 FDD |
|
Channel bandwidth |
MHz |
10 |
10 |
10 |
5 |
10 |
10 |
20 |
15 |
20 |
10 |
15 |
10 |
Allocated resource blocks (Note 4) |
50 |
50 |
50 |
25 |
40 |
50 |
100 |
75 |
100 |
50 |
75 |
50 |
|
Allocated subframes per Radio Frame |
9 |
9 |
8 |
9 |
9 |
9 |
9 |
8 |
8 |
9 |
8 |
8 |
|
Modulation |
QPSK |
16QAM |
16QAM |
16QAM |
16QAM |
QPSK |
16QAM |
16QAM |
64QAM |
64QAM |
64QAM |
64QAM |
|
Target Coding Rate |
1/3 |
1/2 |
1/2 |
1/2 |
1/2 |
1/2 |
1/2 |
1/2 |
0.39 |
1/2 |
0.39 |
0.39 |
|
Information Bit Payload (Note 4) |
|||||||||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
4392 |
12960 |
12960 |
5736 |
10296 |
6968 |
25456 |
19080 |
30576 |
19848 |
22920 |
15264 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
4392 |
12960 |
N/A |
4968 |
10296 |
6968 |
25456 |
N/A |
N/A |
18336 |
N/A |
N/A |
Number of Code Blocks |
|||||||||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
1 |
3 |
3 |
1 |
2 |
2 |
5 |
4 |
5 |
4 |
4 |
3 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
1 |
3 |
N/A |
1 |
2 |
2 |
5 |
N/A |
N/A |
3 |
N/A |
N/A |
Binary Channel Bits (Note 4) |
|||||||||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
13200 |
26400 |
26400 |
12000 |
21120 |
13200 |
52800 |
39600 |
79200 |
39600 |
59400 |
39600 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
12384 |
24768 |
N/A |
10368 |
19488 |
12384 |
51168 |
N/A |
N/A |
37152 |
N/A |
N/A |
Max. Throughput averaged over 1 frame (Note 4) |
Mbps |
3.953 |
11.664 |
10.368 |
5.086 |
9.266 |
6.271 |
22.910 |
15.264 |
24.461 |
17.712 |
18.336 |
12.211 |
UE Category |
≥ 1 |
≥ 2 |
≥ 2 |
≥ 1 |
≥ 1 |
≥ 1 |
≥ 2 |
≥ 2 |
4 |
≥ 2 |
≥ 2 |
≥ 2 |
|
Note 1: 2 symbols allocated to PDCCH for 20 MHz, 15 MHz and 10 MHz channel BW; 3 symbols allocated to PDCCH for 5 MHz and 3 MHz; 4 symbols allocated to PDCCH for 1.4 MHz. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). Note 4: Given per component carrier per codeword. Note 5: For R.11-3 resource blocks of RB6–RB45 are allocated. |
Table A.3.3.2.1-2: Fixed Reference Channel two antenna ports
Parameter |
Unit |
Value |
|||||||||||
Reference channel |
R.46 FDD |
R.47 FDD |
R.35-4 FDD |
R.11-5 FDD |
R.11-6 FDD |
R.11-7 FDD |
R.11-8 FDD |
R.11- 9 FDD |
R.11- 10 FDD |
R.65 FDD |
R.10-2 FDD |
R.10-3 FDD |
|
Channel bandwidth |
MHz |
10 |
10 |
10 |
1.4 |
3 |
15 |
10 |
10 |
10 |
10 |
5 |
10 |
Allocated resource blocks (Note 4) |
50 |
50 |
50 |
6 |
15 |
75 |
50 |
50 |
50 |
50 |
25 |
50 |
|
Allocated number of PDCCH symbols |
2 |
2 |
2 |
4 |
3 |
2 |
2 |
3 |
3 |
2 |
3 |
2 |
|
Allocated subframes per Radio Frame |
9 |
9 |
9 |
8 |
9 |
9 |
9 |
8 |
8 |
8 |
9 |
9 |
|
Modulation |
QPSK |
16QAM |
64QAM |
16QAM |
16QAM |
16QAM |
QPSK |
QPSK |
QPSK |
256QAM |
QPSK |
16QAM |
|
Target Coding Rate |
0.47 |
1/2 |
1/2 |
1/2 |
3/5 |
0.58 |
0.67 |
0. 55 |
1/3 |
0.58 |
|||
Information Bit Payload (Note 4) |
|||||||||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
5160 |
8760 |
18336 |
1352 |
3368 |
19080 |
7992 |
6968 |
7992 |
31704 |
1800 |
15264 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
n/a |
n/a |
For Sub-Frame 0 |
Bits |
5160 |
8760 |
16416 |
N/A |
2664 |
19080 |
6968 |
N/A |
N/A |
N/A |
1800 |
14112 |
Number of Code Blocks |
|||||||||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
1 |
2 |
3 |
1 |
1 |
4 |
2 |
2 |
2 |
6 |
1 |
3 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
n/a |
n/a |
For Sub-Frame 0 |
Bits |
1 |
2 |
3 |
1 |
1 |
4 |
2 |
N/A |
N/A |
N/A |
1 |
3 |
Binary Channel Bits (Note 4) |
|||||||||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
13200 |
26400 |
39600 |
2592 |
7200 |
39600 |
13200 |
12000 |
12000 |
57600 |
6000 |
26400 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
n/a |
n/a |
For Sub-Frame 0 |
Bits |
12384 |
24768 |
37152 |
N/A |
5568 |
37968 |
12384 |
N/A |
N/A |
N/A |
5184 |
24768 |
Max. Throughput averaged over 1 frame (Note 4) |
Mbps |
4.644 |
7.884 |
16.310 |
1.082 |
2.961 |
17.172 |
7.0904 |
5.5744 |
6.3936 |
25.363 |
1.620 |
13.6224 |
UE Category |
≥ 1 |
≥ 1 |
≥ 2 |
≥ 1 |
≥ 1 |
≥ 2 |
≥ 2 |
≥ 1 |
≥ 1 |
11-12 |
≥ 1 |
≥ 2 |
|
UE DL Category |
≥ 6 |
≥ 6 |
≥ 6 |
≥ 6 |
≥ 6 |
≥ 6 |
≥ 6 |
≥ 11 |
≥ 6 |
||||
Note 1: Void Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4] Note 3: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit) Note 4: Given per component carrier per codeword. |
Table A.3.3.2.1-3: Fixed Reference Channel two antenna ports
Parameter |
Unit |
Value |
|
Reference channel |
R.62 FDD |
R.63 FDD |
|
Channel bandwidth |
MHz |
10 |
10 |
Allocated resource blocks (Note 4) |
3 |
1 |
|
Allocated DL subframes per 4 Radio Frames (Note 3) |
15 |
15 |
|
Modulation |
16QAM |
64QAM |
|
Target Coding Rate |
1/2 |
1/2 |
|
Information Bit Payload |
|||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Bits |
744 |
408 |
Number of Code Blocks |
|||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Code blocks |
1 |
1 |
Binary Channel Bits |
|||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Bits |
1584 |
792 |
Max. Throughput averaged over 4 frames |
Mbps |
0.279 |
0.153 |
UE DL Category |
0 |
0 |
|
Note 1: 2 symbols allocated to PDCCH Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4] Note 3: The downlink subframes are scheduled at the 0th, 1st, 2nd, 8th, 9th, 10th, 16th, 17th, 18th, 24th, 25th, 26th, 32nd, 33rd, 34th subframes every 40ms. Information bit payload is available if downlink subframe is scheduled. Note 4: Allocated PRB positions start from {9, 10, …, 9+N-1}, where N is the number of allocated resource blocks. |
Table A.3.3.2.1-4: Fixed Reference Channel two antenna ports
Parameter |
Unit |
Values |
||
Reference channel |
R.79 FDD |
R.103 FDD |
R.104 FDD |
|
Channel bandwidth |
MHz |
10 |
10 |
10 |
Allocated DL subframes per Radio Frame |
Note 3 |
Note 5 |
Note 3 Note 6 |
|
Allocated DL subframes per Radio Frame |
Note 3 |
Note 5 |
Note 3 |
|
Modulation |
16QAM |
QPSK |
64QAM |
|
Target Coding Rate |
1/2 |
1/3 |
0.4 |
|
Information Bit Payload |
||||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Bits |
744 |
224 |
968 |
Number of Code Blocks |
||||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Code blocks |
1 |
1 |
1 |
Binary Channel Bits |
||||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Bits |
1584 |
792 |
2376 |
Max. Throughput averaged over 1 frame |
Mbps |
0.149 |
0.0187 |
0.194 |
UE DL Category |
M1, M2 ≥ 0 |
M1, M2 |
M1, M2 |
|
Note 1: 2 symbols allocated to PDCCH. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: The downlink subframes are scheduled at the 0th and 1st subframes every 10ms. Information bit payload is available if downlink subframe is scheduled (starting from 0th subframe). The corresponding MPDCCH is scheduled 2 subframes before the corresponding PDSCH transmissions. Note 4: Allocated PRB positions for PDSCH are {3, 4, 5} within the assigned narrowband. Allocated PRB positions for MPDCCH are {0, 1} within the assigned narrowband. Note 5: The downlink subframes are scheduled at the 0th subframes every 12ms. Information bit payload is available if downlink subframe is scheduled (starting from 5th subframe). The corresponding MPDCCH is scheduled 5 subframes before the corresponding PDSCH transmissions. Note 6: For case with 14 HARQ processes, scheduling pattern is 17ms. In every scheduling period, subframes from 0 to 11 are used for MPDCCH and MPDSCH transmission, the corresponding MPDCCH is scheduled 2 subframes before the corresponding PDSCH transmissions which are scheduled in subframes from 2 to 11. The corresponding MPDCCH is scheduled 7 subframes before the corresponding PDSCH transmissions which are scheduled in subframes 0 and 1. Subframe 13 is used for ACK/NACK feedback corresponding to MPDSCH transmitted in subframe from 0 to 3; Subframe 14 is used for ACK/NACK feedback corresponding to MPDSCH transmitted in subframe from 4 to 7; Subframe 15 is used for ACK/NACK feedback corresponding to MPDSCH transmitted in subframe from 8 to 11. Subframes 12 and 16 are used for gaps. |
Table A.3.3.2.1-5: Fixed Reference Channel two antenna ports
Parameter |
Unit |
Values |
||
Reference channel |
R.81 FDD |
R.81-1 FDD |
R.81-2 FDD |
|
Channel bandwidth |
MHz |
10 |
10 |
10 |
Allocated resource blocks (Note 4) |
6 |
6 |
6 |
|
Allocated PDSCH subframes |
(Note 3) |
(Note 6) |
(Note 7) |
|
Modulation |
QPSK |
QPSK |
QPSK |
|
Target Coding Rate |
1/10 |
1/10 |
1/10 |
|
Information Bit Payload |
||||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Bits |
152 |
152 |
152 |
Number of Code Blocks |
||||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Code blocks |
1 |
1 |
1 |
Binary Channel Bits |
||||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Bits |
1584 |
1584 |
1584 |
Max. Throughput averaged over one period |
kbps |
0.950 |
1.9 |
4.75 |
UE DL Category |
M1, ≥ 0 |
≥1 |
≥1 |
|
Note 1: 2 symbols allocated to PDCCH Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4] Note 3: PDSCH subframes are scheduled at the 65th to 128th subframes every period=160 ms. Information bit payload is available at the 65th to 128th subframes with repetition. (Starting from the 0th subframe) Note 4: Allocated PRB positions are {0, 1, 2, 3, 4, 5} within the assigned narrowband. Note 5: MPDCCH are scheduled at the 0th to 63rd subframes with repetition. The allocated PRB positions are {0, 1, 2, 3, 4, 5} within the assigned narrowband. (Starting from the 0th subframe) Note 6: PDSCH subframes are scheduled at the 33th to 64th subframes every period=80 ms. Information bit payload is available at the 33th to 64th subframes with repetition. (Starting from the 0th subframe) Note 7: PDSCH subframes are scheduled at the 9th to 24th subframes every period=32 ms. Information bit payload is available at the 9th to 24th subframes with repetition. (Starting from the 0th subframe) |
Table A.3.3.2.1-6: Fixed Reference Channel two antenna ports
Parameter |
Unit |
Values |
|||||||
Reference channel |
R.87 FDD |
R.87-1 FDD |
R.84 FDD |
R.aa FDD |
R.bb FDD |
R.87-2 FDD |
R.87-3 FDD |
R.87-4 FDD |
|
Channel bandwidth |
MHz |
10 |
10 |
10 |
10 |
10 |
5 |
15 |
20 |
Allocated resource blocks (Note 4) |
50 |
50 |
39 |
50 |
50 |
25 |
75 |
100 |
|
Allocated number of PDCCH symbols |
2 |
2 |
2 |
2 |
2 |
2 |
2 |
2 |
|
Allocated subframes per Radio subframes |
8 |
8 |
9 |
9 |
9 |
8 |
8 |
8 |
|
Modulation |
64QAM |
16QAM |
16QAM |
QPSK |
16QAM |
64QAM |
64QAM |
64QAM |
|
Target Coding Rate |
|||||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
0.39 |
0.44 |
1/2 |
0.6 |
0.3 |
0.39 |
0.39 |
0.39 |
|
For Sub-Frames 5 |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
|
For Sub-Frames 0 |
N/A |
N/A |
N/A |
0.65 |
0.32 |
N/A |
N/A |
N/A |
|
Information Bit Payload (Note 4) |
|||||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
15264 |
11448 |
9912 |
7992 |
7992 |
7736 |
22920 |
30576 |
For Sub-Frames 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
For Sub-Frames 0 |
N/A |
N/A |
9912 |
7992 |
7992 |
N/A |
N/A |
N/A |
|
Number of Code Blocks(Notes 3 and 4) |
|||||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
3 |
2 |
2 |
2 |
2 |
2 |
4 |
5 |
|
For Sub-Frames 5 |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
|
For Sub-Frames 0 |
N/A |
N/A |
2 |
2 |
2 |
N/A |
N/A |
N/A |
|
Binary Channel Bits (Note 4) |
|||||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
39600 |
26400 |
20592 |
13200 |
26400 |
19800 |
59400 |
79200 |
For Sub-Frames 5 |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
|
For Sub-Frames 0 |
N/A |
N/A |
20592 |
12384 |
24768 |
N/A |
N/A |
N/A |
|
Max. Throughput averaged over 1 frame (Note 4) |
Mbps |
12.211 |
9.158 |
8.9208 |
7.1928 |
7.1928 |
6.1888 |
18.336 |
24.461 |
UE Category |
≥ 1 |
≥ 1 |
1bis |
≥ 1 |
≥ 2 |
≥ 1 |
≥ 1 |
≥ 1 |
|
UE DL Category |
≥ 6 |
≥ 6 |
N/A |
≥ 6 |
≥ 6 |
≥ 6 |
≥ 6 |
≥ 6 |
|
Note 1: Void Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4] Note 3: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit) Note 4: Given per component carrier per codeword. Note 5: For R.84 FDD, 39 RBs are allocated on RB 0-20 and 30-47. |
Table A.3.3.2.1-7: Fixed Reference Channel two antenna ports
Parameter |
Unit |
Value |
|||
Reference channel |
R.47-1 FDD |
R.47-2 FDD |
R.47-3 FDD |
||
Channel bandwidth |
MHz |
5 |
15 |
20 |
|
Allocated resource blocks (Note 4) |
25 |
75 |
100 |
||
Allocated number of PDCCH symbols |
2 |
2 |
2 |
||
Allocated subframes per Radio Frame |
9 |
9 |
9 |
||
Modulation |
16QAM |
16QAM |
16QAM |
||
Target Coding Rate |
|||||
Information Bit Payload (Note 4) |
|||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
4008 |
12960 |
17568 |
|
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
|
For Sub-Frame 0 |
Bits |
3496 |
12960 |
17568 |
|
Number of Code Blocks |
|||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
1 |
3 |
3 |
|
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
|
For Sub-Frame 0 |
Bits |
1 |
3 |
3 |
|
Binary Channel Bits (Note 3) |
|||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
12000 |
39600 |
52800 |
|
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
|
For Sub-Frame 0 |
Bits |
10368 |
37968 |
51168 |
|
Max. Throughput averaged over 1 frame (Note 3) |
Mbps |
3.556 |
11.664 |
15.8112 |
|
UE Category |
≥ 1 |
≥ 1 |
≥ 1 |
||
UE DL Category |
≥ 6 |
≥ 6 |
≥ 6 |
||
Note 1: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4] Note 2: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit) Note 3: Given per component carrier per codeword. |
Table A.3.3.2.1-8: Fixed Reference Channel two antenna ports
Parameter |
Unit |
Values |
||||
Reference channel |
R.90 FDD |
R.91 FDD |
R.92-1 FDD |
R.92-2 FDD |
||
Channel bandwidth |
MHz |
10 |
10 |
10 |
10 |
|
Allocated resource blocks |
18 (Note 7) |
18 (Note 7) |
36 (Note 8) |
36 (Note 8) |
||
Allocated DL subframes |
Note 3 |
Note 4 |
Note 5 |
Note 6 |
||
Modulation |
QPSK |
QPSK |
QPSK |
QPSK |
||
Target Coding Rate |
1/3 |
1/10 |
1/2 |
1/2 |
||
Information Bit Payload |
||||||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Bits |
1544 |
488 |
4392 |
4392 |
|
Number of Code Blocks |
||||||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Code blocks |
1 |
1 |
1 |
1 |
|
Binary Channel Bits |
||||||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Bits |
4752 |
4752 |
9504 |
9504 |
|
Max. Throughput averaged over one period |
kbps |
48.25 |
3.8125 |
219.6 |
439.2 |
|
UE DL Category |
M2 |
M2 |
≥ 1 |
≥ 1 |
||
Note 1: 2 symbols allocated to PDCCH Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4] Note 3: The downlink subframes are scheduled at the 0th to 24th subframes every period=32 ms. Information bit payload is available at the 17th to 24th subframes with repetition. MPDCCH are scheduled at the 0th to 15th subframes with repetition. (Starting from the 0th subframe) Note 4: The downlink subframes are scheduled at the 0th to 96th subframes every period=128 ms. Information bit payload is available at the 65th to 96th subframes with repetition. MPDCCH are scheduled at the 0th to 63rd subframes with repetition. (Starting from the 0th subframe) Note 5: The downlink subframes are scheduled at the 0th to 12th subframes every period= 20 ms. Information bit payload is available at the 9th to 12th subframes with repetition. MPDCCH are scheduled at the 0th to 7th subframes with repetition. (Starting from the 0th subframe) Note 6: The downlink subframes are scheduled at the 0th to 4th subframes every period=10 ms. Information bit payload is available at the 3rd to 4th subframes with repetition. MPDCCH are scheduled at the 0th to 1st subframes with repetition. (Starting from the 0th subframe) Note 7: Allocated PRB positions are {0, 1, …, 17} within the assigned wideband. Note 8: Allocated PRB positions are {1, 2, 3, …, 18, 31, 32, …, 48}. Note 9: Allocated PRB positions for MPDCCH are {0, 1, 2, 3, 4, 5} within the scheduled narrowband. |
Table A.3.3.2.1-9: Fixed Reference Channel two antenna ports
Parameter |
Unit |
Value |
|
Reference channel |
R.11-13 FDD |
||
Channel bandwidth |
MHz |
10 |
|
Allocated resource blocks (Note 4) |
50 |
||
Allocated subframes per Radio Frame |
9 |
||
Modulation |
16QAM |
||
Target Coding Rate |
1/2 |
||
Information Bit Payload (Note 4) |
|||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
10680 |
|
For Sub-Frame 5 |
Bits |
N/A |
|
For Sub-Frame 0 |
Bits |
10680 |
|
Number of Code Blocks |
|||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
2 |
|
For Sub-Frame 5 |
Bits |
N/A |
|
For Sub-Frame 0 |
Bits |
2 |
|
Binary Channel Bits (Note 4) |
|||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
21648 |
|
For Sub-Frame 5 |
Bits |
N/A |
|
For Sub-Frame 0 |
Bits |
17424 |
|
Max. Throughput averaged over 1 frame (Note 4) |
Mbps |
9.612 |
|
UE Category |
≥ 2 |
||
Note 1: 2 symbols allocated to PDCCH. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). Note 4: Given per component carrier per codeword. Note 5: 41 resource blocks (RB0–RB20 and RB30–RB49) are allocated in sub-frame 0,1,2,3,4,6,7,8,9. |
A.3.3.2.2 Four antenna ports
Table A.3.3.2.2-1: Fixed Reference Channel four antenna ports
Parameter |
Unit |
Value |
|||||||||||
Reference channel |
R.12 FDD |
R.13 FDD |
R.14 FDD |
R.14-1 FDD |
R.14-2 FDD |
R.14-3 FDD |
R.36 FDD |
R.14-4 FDD |
R.14-5 FDD |
R.14-6 FDD |
R.14-7 FDD |
R.36-1 FDD |
|
Channel bandwidth |
MHz |
1.4 |
10 |
10 |
10 |
10 |
20 |
10 |
1.4 |
3 |
5 |
15 |
10 |
Allocated resource blocks (Note 4) |
6 |
50 |
50 |
6 |
3 |
100 |
50 |
6 |
15 |
25 |
75 |
50 |
|
Allocated subframes per Radio Frame |
9 |
9 |
9 |
8 |
8 |
9 |
9 |
8 |
9 |
9 |
9 |
9 |
|
Modulation |
QPSK |
QPSK |
16QAM |
16QAM |
16QAM |
16QAM |
64QAM |
16QAM |
16QAM |
16QAM |
16QAM |
64QAM |
|
Target Coding Rate |
1/3 |
1/3 |
1/2 |
1/2 |
1/2 |
1/2 |
1/2 |
1/2 |
1/2 |
1/2 |
1/2 |
0.55 |
|
Information Bit Payload (Note 4) |
|||||||||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
408 |
4392 |
12960 |
1544 |
744 |
25456 |
18336 |
1192 |
3368 |
5736 |
19080 |
21384 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
n/a |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
152 |
3624 |
11448 |
N/A |
N/A |
22920 |
18336 |
N/A |
2664 |
4968 |
19080 |
19848 |
Number of Code Blocks |
|||||||||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
1 |
1 |
3 |
1 |
1 |
5 |
3 |
1 |
1 |
1 |
4 |
4 |
|
For Sub-Frame 5 |
N/A |
N/A |
N/A |
N/A |
N/A |
n/a |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
|
For Sub-Frame 0 |
1 |
1 |
2 |
N/A |
N/A |
4 |
3 |
N/A |
1 |
1 |
4 |
4 |
|
Binary Channel Bits (Note 4) |
|||||||||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
1248 |
12800 |
25600 |
3072 |
1536 |
51200 |
38400 |
2496 |
6960 |
11600 |
38400 |
38400 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
n/a |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
480 |
12032 |
24064 |
N/A |
N/A |
49664 |
36096 |
N/A |
5424 |
10064 |
36864 |
36096 |
Max. Throughput averaged over 1 frame (Note 4) |
Mbps |
0.342 |
3.876 |
11.513 |
1.235 |
0.595 |
22.656 |
16.502 |
0.954 |
2.961 |
5.086 |
17.172 |
19.092 |
UE Category |
≥ 1 |
≥ 1 |
≥ 2 |
≥ 1 |
≥ 1 |
≥ 2 |
≥ 2 |
≥ 1 |
≥ 1 |
≥ 1 |
≥ 2 |
≥ 2 |
|
Note 1: 2 symbols allocated to PDCCH for 20 MHz, 15 MHz and 10 MHz channel BW; 3 symbols allocated to PDCCH for 5 MHz and 3 MHz; 4 symbols allocated to PDCCH for 1.4 MHz. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). Note 4: Given per component carrier per codeword. |
Table A.3.3.2.2-2: Fixed Reference Channel four antenna ports
Parameter |
Unit |
Value |
||||||||
Reference channel |
R.72 FDD |
R.72-1 FDD |
R.72-2 FDD |
R.72-3 FDD |
R.73 FDD |
R.73-1 FDD |
R.74 FDD |
R.85 FDD |
R.93 FDD |
|
Channel bandwidth |
MHz |
10 |
5 |
15 |
20 |
10 |
10 |
10 |
10 |
10 |
Allocated resource blocks (Note 4) |
50 |
25 |
75 |
100 |
50 |
50 |
50 |
24 (Note 5) |
24 (Note 5) |
|
Allocated subframes per Radio Frame |
9 |
9 |
9 |
9 |
9 |
9 |
9 |
9 |
9 |
|
Modulation |
256QAM |
256QAM |
256QAM |
256QAM |
64QAM |
16QAM |
16QAM |
64QAM |
64QAM |
|
Target Coding Rate |
0.62 |
0.69 |
0.61 |
0.62 |
0.43 |
1/2 |
1/2 |
1/2 |
0.52 |
|
Information Bit Payload (Note 4) |
||||||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
31704 |
15840 |
46888 |
63776 |
16416 (CW0) 32856 (CW1) |
12960 (CW0) 25456 (CW1) |
25456 |
10296 |
9528 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
31704 |
15840 |
46888 |
63776 |
15264 (CW0) 30576 (CW1) |
11448 (CW0) 22920 (CW1) |
22920 |
10296 |
9528 |
Number of Code Blocks |
||||||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
6 |
3 |
8 |
11 |
3 (CW0) 6 (CW1) |
3 (CW0) 5 (CW1) |
5 |
2 |
2 |
|
For Sub-Frame 5 |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
|
For Sub-Frame 0 |
6 |
3 |
8 |
11 |
3 (CW0) 5 (CW1) |
2 (CW0) 4 (CW1) |
5 |
2 |
2 |
|
Binary Channel Bits (Note 4) |
||||||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
51200 |
23200 |
76800 |
102400 |
38400 (CW0) 76800 (CW1) |
25600 (CW0) 51200 (CW1) |
51200 |
18432 |
18432 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
48128 |
20128 |
73728 |
99328 |
36096 (CW0) 72192 (CW1) |
24064 (CW0) 48128 (CW1) |
48128 |
18432 |
18432 |
Max. Throughput averaged over 1 frame (Note 4) |
Mbps |
28.534 |
14.256 |
42.1992 |
57.3984 |
14.659 (CW0) 29.342 (CW1) |
11.513 (CW0) 22.657 (CW1) |
22.657 |
9.2664 |
8.575 |
UE Category |
≥ 11 |
≥ 11 |
≥ 11 |
≥ 11 |
≥ 5 |
≥ 5 |
≥ 5 |
1bis |
1bis |
|
Note 1: 2 symbols allocated to PDCCH for 20 MHz, 15 MHz and 10 MHz channel BW; 3 symbols allocated to PDCCH for 5 MHz and 3 MHz; 4 symbols allocated to PDCCH for 1.4 MHz. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). Note 4: Given per component carrier per codeword. Note 5: 24 resource blocks (RB 0-20 and 30-32) are allocated in sub-frames 0, 1, 2, 3, 4, 6, 7, 8, 9 |
Table A.3.3.2.2-3: Fixed Reference Channel four antenna ports
Parameter |
Unit |
Value |
||||
Reference channel |
R.74-1 FDD |
R.74-2 FDD |
R.74-3 FDD |
R.101 FDD |
||
Channel bandwidth |
MHz |
5 |
15 |
20 |
10 |
|
Allocated resource blocks (Note 4) |
25 |
75 |
100 |
50 |
||
Allocated subframes per Radio Frame |
9 |
9 |
9 |
9 |
||
Modulation |
16QAM |
16QAM |
16QAM |
1024QAM |
||
Target Coding Rate |
1/2 |
1/2 |
1/2 |
3/4 |
||
Information Bit Payload (Note 4) |
||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
11448 |
37888 |
51024 |
52752 |
|
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
|
For Sub-Frame 0 |
Bits |
9912 |
37888 |
51024 |
N/A |
|
Number of Code Blocks |
||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
2 |
7 |
9 |
9 |
||
For Sub-Frame 5 |
N/A |
N/A |
N/A |
N/A |
||
For Sub-Frame 0 |
2 |
7 |
9 |
N/A |
||
Binary Channel Bits (Note 4) |
||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
23200 |
76800 |
102400 |
68000 |
|
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
|
For Sub-Frame 0 |
Bits |
20128 |
73728 |
99328 |
N/A |
|
Max. Throughput averaged over 1 frame (Note 4) |
Mbps |
10.1496 |
34.0992 |
45.9216 |
42.2016 |
|
UE Category |
≥ 5 |
≥ 5 |
≥ 5 |
TBD |
||
UE DL Category |
20, ≥ 22 |
|||||
Note 1: 2 symbols allocated to PDCCH for 20 MHz, 15 MHz and 10 MHz channel BW; 3 symbols allocated to PDCCH for 5 MHz and 3 MHz; 4 symbols allocated to PDCCH for 1.4 MHz. 1 symbol allocated to PDCCH for reference channel with 1024QAM. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). Note 4: Given per component carrier per codeword. |
Table A.3.3.2.2-4: Fixed Reference Channel four antenna ports
Parameter |
Unit |
Values |
Reference channel |
R.95 FDD |
|
Channel bandwidth |
MHz |
10 |
Allocated resource blocks (Note 4) |
3 |
|
Allocated DL subframes per Radio Frame (Note 3) |
2 |
|
Modulation |
16QAM |
|
Target Coding Rate |
1/2 |
|
Information Bit Payload |
||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Bits |
744 |
Number of Code Blocks |
||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Code blocks |
1 |
Binary Channel Bits |
||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Bits |
1536 |
Max. Throughput averaged over 1 frame |
Mbps |
0.149 |
UE DL Category |
M2 |
|
Note 1: 2 symbols allocated to PDCCH. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: The downlink subframes are scheduled at the 0th and 1st subframes every 10ms. Information bit payload is available if downlink subframe is scheduled (starting from 0th subframe). The corresponding MPDCCH is scheduled 2 subframes before the corresponding PDSCH transmissions. Note 4: Allocated PRB positions for PDSCH are {3, 4, 5} within the assigned narrowband. Allocated PRB positions for MPDCCH are {0, 1} within the assigned narrowband. |
A.3.3.3 Reference Measurement Channel for UE-Specific Reference Symbols
A.3.3.3.0 Two antenna ports (no CSI-RS)
The reference measurement channels in Table A.3.3.3.0-1 apply with two CRS antenna ports and without CSI-RS.
Table A.3.3.3.0-1: Fixed Reference Channel without CSI-RS
Parameter |
Unit |
Value |
||||
Reference channel |
R.70 FDD |
R.71 FDD |
||||
Channel bandwidth |
MHz |
10 |
10 |
|||
Allocated resource blocks |
50 |
50 |
||||
Allocated subframes per Radio Frame |
10 |
10 |
||||
Modulation |
QPSK |
16QAM |
||||
Target Coding Rate |
0.65 |
0.6 |
||||
Information Bit Payload |
||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
6968 |
12960 |
|||
For Sub-Frame 5 |
Bits |
N/A |
N/A |
|||
For Sub-Frame 0 |
Bits |
N/A |
N/A |
|||
Number of Code Blocks per Sub-Frame |
||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
2 |
3 |
||||
For Sub-Frame 5 |
N/A |
N/A |
||||
For Sub-Frame 0 |
N/A |
N/A |
||||
Binary Channel Bits Per Sub-Frame |
||||||
For Sub-Frames 1,2,3,4,6,7,8,9 |
Bits |
10800 |
21600 |
|||
For Sub-Frame 5 |
Bits |
N/A |
N/A |
|||
For Sub-Frame 0 |
Bits |
N/A |
N/A |
|||
Max. Throughput averaged over 1 frame |
Mbps |
5.5744 |
10.368 |
|||
UE Category |
≥ 1 |
≥ 2 |
||||
Note 1: 3 symbols allocated to PDCCH. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4] Note 3: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit) |
The reference measurement channels in Table A.3.3.3.0-2 apply for verifying demodulation performance for UE-specific reference symbols without CSI-RS.
Table A.3.3.3.0-2: Fixed Reference Channel without CSI-RS
Parameter |
Unit |
Value |
|||
Reference channel |
R.80 FDD |
R.80-1 FDD |
R.80-2 FDD |
||
Channel bandwidth |
MHz |
10 |
10 |
10 |
|
Allocated resource blocks (Note 4) |
6 |
6 |
6 |
||
Allocated PDSCH subframes |
Note 3 |
Note 6 |
Note 7 |
||
Modulation |
QPSK |
QPSK |
QPSK |
||
Target Coding Rate |
1/3 |
1/3 |
1/3 |
||
Information Bit Payload |
|||||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Bits |
504 |
504 |
504 |
|
Number of Code Blocks |
|||||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Code blocks |
1 |
1 |
1 |
|
Binary Channel Bits |
|||||
For Sub-Frames 0,1,2,3,4,5,6,7,8,9 |
Bits |
1440 |
1440 |
1440 |
|
Max. Throughput averaged over one period |
kbps |
15.75 |
31.5 |
50.4 |
|
UE DL Category |
M1, ≥ 0 |
≥1 |
≥1 |
||
Note 1: 2 symbols allocated to PDCCH Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4] Note 3: PDSCH subframes are scheduled at the 9th to 16th subframes every period=32 ms. Information bit payload is availabled from the 9-th to 16th subframes with repetition. (Starting from the 0th subframe) Note 4: Allocated PRB positions are {0, 1, 2, 3, 4, 5} within the assigned narrowband. Note 5: MPDCCH are scheduled at the 0th to 7th subframes with repetition. The allocated PRB positions are {0, 1, 2, 3, 4, 5} within the assigned narrowband. (Starting from the 0th subframe) Note 6: PDSCH subframes are scheduled at the 3th to 6th subframes every period=16 ms. Information bit payload is availabled from the 3th to 6th subframes with repetition. (Starting from the 0th subframe) Note 7: PDSCH subframes are scheduled at the 2th to 3th subframes every period=10 ms. Information bit payload is availabled from the 2th to 3th subframes with repetition. (Starting from the 0th subframe) |
A.3.3.3.1 Two antenna port (CSI-RS)
The reference measurement channels in Table A.3.3.3.1-1 apply for verifying demodulation performance for UE-specific reference symbols with two cell-specific antenna ports and two CSI-RS antenna ports.
Table A.3.3.3.1-1: Fixed Reference Channel for CDM-multiplexed DM RS with two CSI-RS antenna ports
Parameter |
Unit |
Value |
|||||||||
Reference channel |
R.51 FDD |
R.51-1 FDD |
R.76 FDD |
R.51-2 FDD |
R.51-3 FDD |
R.51-4 FDD |
R.86 FDD |
R.86A FDD |
R.X FDD |
R.94 FDD |
|
Channel bandwidth |
MHz |
10 |
10 |
10 |
5 |
15 |
20 |
10 |
10 |
10 |
10 |
Allocated resource blocks |
50 (Note 3) |
50 (Note 3) |
50 (Note 3) |
25 (Note 5) |
75 (Note 6) |
100 (Note 7) |
50 (Note 3) |
50 (Note 3) |
50 (Note 3) |
24 (Note 8) |
|
Allocated subframes per Radio Frame |
9 |
9 |
9 |
9 |
9 |
9 |
9 |
9 |
9 |
9 |
|
Modulation |
16QAM |
16QAM |
QPSK |
16QAM |
16QAM |
16QAM |
QPSK |
QPSK |
64QAM |
QPSK |
|
Target Coding Rate |
1/2 |
0.54 |
1/2 |
1/2 |
1/2 |
1/3 |
1/3 |
1/2 |
2/3 |
||
Information Bit Payload |
|||||||||||
For Sub-Frames 1,4,6,9 |
Bits |
11448 |
12960 |
6200 |
5736 |
16992 |
22920 |
4392 |
3624 |
18336 |
3752 |
For Sub-Frames 2,3,7,8 |
Bits |
11448 |
12960 |
6200 |
5736 |
16992 |
22920 |
4392 |
3624 |
18336 |
3752 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
n/a |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
9528 |
10680 |
4968 |
3880 |
14112 |
19848 |
3624 |
2984 |
14688 |
3752 |
Number of Code Blocks (Note 4) |
|||||||||||
For Sub-Frames 1,4,6,9 |
Code blocks |
2 |
3 |
2 |
1 |
3 |
4 |
1 |
1 |
3 |
1 |
For Sub-Frames 2,3,7,8 |
Code blocks |
2 |
3 |
2 |
1 |
3 |
4 |
1 |
1 |
3 |
1 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
n/a |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
2 |
2 |
1 |
1 |
3 |
4 |
1 |
1 |
3 |
1 |
Binary Channel Bits |
|||||||||||
For Sub-Frames 1,4,6,9 |
Bits |
24000 |
24000 |
12000 |
10800 |
36000 |
48000 |
12000 |
11600 |
36000 |
5760 |
For Sub-Frames 2,7 |
23600 |
23600 |
11800 |
10600 |
35400 |
47200 |
11800 |
11600 |
35400 |
5664 |
|
For Sub-Frames 3,8 |
23200 |
23200 |
12000 |
10400 |
34800 |
46400 |
11600 |
11200 |
34800 |
5568 |
|
For Sub-Frame 5 |
Bits |
N/A |
N/A |
n/a |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
19680 |
19680 |
9840 |
6912 |
30240 |
42240 |
11184 |
9512 |
29520 |
5760 |
Max. Throughput averaged over 1 frame |
Mbps |
10.1112 |
11.436 |
5.4568 |
4.9768 |
15.0048 |
20.3208 |
3.876 |
3.1976 |
16.138 |
3.376 |
UE Category |
≥ 2 |
≥ 2 |
≥ 2 |
≥ 2 |
≥ 2 |
≥ 2 |
1bis |
≥ 1 |
≥ 2 |
1bis |
|
Note 1: 2 symbols allocated to PDCCH for 20 MHz, 15 MHz and 10 MHz channel BW; 3 symbols allocated to PDCCH for 5 MHz and 3 MHz; 4 symbols allocated to PDCCH for 1.4 MHz. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: 50 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 41 resource blocks (RB0–RB20 and RB30–RB49) are allocated in sub-frame 0. Note 4: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). Note 5: 25 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 17 resource blocks (RB0–RB9 and RB18–RB24) are allocated in sub-frame 0. Note 6: 75 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 63 resource blocks (RB0–R31 and RB44–RB74) are allocated in sub-frame 0. Note 7: 100 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 88 resource blocks (RB0–RB43 and RB56–RB99) are allocated in sub-frame 0. Note 8: 24 resource blocks (RB 0-20 and 30-32) are allocated in sub-frames 0, 1, 2, 3, 4, 6, 7, 8, 9 |
The reference measurement channels in Table A3.3.3.1-2 apply for verifying demudlation performance for UE-specific reference symbols with two cell specific antenna ports and two CSI-RS antenna ports with ZP CSI-RS and NZP CSI-RS in same subframe.
Table A.3.3.3.1-2: Fixed Reference Channel for CDM-multiplexed DM RS with two CSI-RS antenna ports with ZP CSI-RS and NZP CSI-RS
Parameter |
Unit |
Value |
||||
Reference channel |
R.52 FDD |
R.52-1 FDD |
R.53 FDD |
R.54 FDD |
R.97 FDD |
|
Channel bandwidth |
MHz |
10 |
10 |
10 |
10 |
10 |
Allocated resource blocks |
50 (Note 3) |
50 (Note 3) |
50 (Note 3) |
50 (Note 3) |
50 (Note 3) |
|
Allocated subframes per Radio Frame |
9 |
9 |
9 |
9 |
9 |
|
Modulation |
64QAM |
16QAM |
64QAM |
16QAM |
16QAM |
|
Target Coding Rate |
1/2 |
0.54 |
1/2 |
1/2 |
1/2 |
|
Information Bit Payload |
||||||
For Sub-Frames 1,3,4,6,8,9 |
Bits |
18336 |
12960 |
18336 |
11448 |
11448 |
For Sub-Frames 2,7 |
Bits |
16416 |
12960 |
16416 |
11448 |
11448 |
For Sub-Frame 5 |
Bits |
n/a |
n/a |
n/a |
n/a |
n/a |
For Sub-Frame 0 |
Bits |
14688 |
10680 |
14688 |
9528 |
9528 |
Number of Code Blocks (Note 4) |
||||||
For Sub-Frames 1,3,4,6,8,9 |
Code blocks |
3 |
3 |
3 |
2 |
2 |
For Sub-Frames 2, 7 |
Code blocks |
3 |
3 |
3 |
2 |
2 |
For Sub-Frame 5 |
Bits |
n/a |
n/a |
n/a |
n/a |
n/a |
For Sub-Frame 0 |
Bits |
3 |
2 |
3 |
2 |
2 |
Binary Channel Bits |
||||||
For Sub-Frames 1,3,4,6,8,9 |
Bits |
36000 |
24000 |
36000 |
24000 |
24000 |
For Sub-Frames 2,7 |
34200 |
22800 |
33600 |
22800 |
22400 |
|
For Sub-Frame 5 |
Bits |
n/a |
n/a |
n/a |
n/a |
n/a |
For Sub-Frame 0 |
Bits |
29520 |
19680 |
29520 |
19680 |
19680 |
Max. Throughput averaged over 1 frame |
Mbps |
15.7536 |
11.436 |
15.7536 |
10.1112 |
10.1112 |
Note 1: 2 symbols allocated to PDCCH. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: 50 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 41 resource blocks (RB0–RB20 and RB30–RB49) are allocated in sub-frame 0. Note 4: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). |
Table A.3.3.3.1-3: Fixed Reference Channel for CDM-multiplexed DM RS with two CSI-RS antenna ports
Parameter |
Unit |
Value |
||||||
Reference channel |
R.76-1 FDD |
R.76-2 FDD |
R.76-3 FDD |
R.76-4 FDD |
R.76-5 FDD |
R.76-6 FDD |
R.76-7 FDD |
|
Channel bandwidth |
MHz |
5 |
15 |
20 |
5 |
10 |
15 |
20 |
Allocated resource blocks |
25 (Note 5) |
75 (Note 6) |
100 (Note 7) |
25 (Note 5) |
50 (Note 3) |
75 (Note 6) |
100 (Note 7) |
|
Allocated subframes per Radio Frame |
9 |
9 |
9 |
9 |
9 |
9 |
9 |
|
Modulation |
QPSK |
QPSK |
QPSK |
QPSK |
QPSK |
QPSK |
QPSK |
|
Target Coding Rate |
||||||||
Information Bit Payload |
||||||||
For Sub-Frames 1,4,6,9 |
Bits |
2600 |
9144 |
12216 |
3496 |
7992 |
11832 |
15840 |
For Sub-Frames 2,3,7,8 |
Bits |
2600 |
9144 |
12216 |
3496 |
7992 |
11832 |
15840 |
For Sub-Frame 5 |
Bits |
n/a |
n/a |
n/a |
n/a |
n/a |
n/a |
n/a |
For Sub-Frame 0 |
Bits |
1736 |
7736 |
10680 |
2344 |
6456 |
9912 |
14112 |
Number of Code Blocks (Note 4) |
||||||||
For Sub-Frames 1,4,6,9 |
Code blocks |
1 |
2 |
2 |
1 |
2 |
2 |
3 |
For Sub-Frames 2,3,7,8 |
Code blocks |
1 |
2 |
2 |
1 |
2 |
2 |
3 |
For Sub-Frame 5 |
Bits |
n/a |
n/a |
n/a |
n/a |
n/a |
n/a |
n/a |
For Sub-Frame 0 |
Bits |
1 |
2 |
2 |
1 |
2 |
2 |
3 |
Binary Channel Bits |
||||||||
For Sub-Frames 1,4,6,9 |
Bits |
5400 |
18000 |
24000 |
5400 |
12000 |
18000 |
24000 |
For Sub-Frames 2,7 |
5300 |
17700 |
23600 |
5300 |
11800 |
17700 |
23600 |
|
For Sub-Frames 3,8 |
5200 |
17400 |
23200 |
5200 |
12000 |
17400 |
23200 |
|
For Sub-Frame 5 |
Bits |
n/a |
n/a |
n/a |
n/a |
n/a |
n/a |
n/a |
For Sub-Frame 0 |
Bits |
3456 |
15120 |
21120 |
3456 |
9840 |
15120 |
21120 |
Max. Throughput averaged over 1 frame |
Mbps |
2.2536 |
8.0888 |
10.8408 |
3.0312 |
7.0392 |
10.4568 |
14.0832 |
UE Category |
≥ 2 |
≥ 2 |
≥ 2 |
≥ 2 |
≥ 2 |
≥ 2 |
≥ 2 |
|
Note 1: 2 symbols allocated to PDCCH for 20 MHz, 15 MHz and 10 MHz channel BW; 3 symbols allocated to PDCCH for 5 MHz and 3 MHz; 4 symbols allocated to PDCCH for 1.4 MHz. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: 50 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 41 resource blocks (RB0–RB20 and RB30–RB49) are allocated in sub-frame 0. Note 4: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). Note 5: 25 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 17 resource blocks (RB0–RB9 and RB18–RB24) are allocated in sub-frame 0. Note 6: 75 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 63 resource blocks (RB0–R31 and RB44–RB74) are allocated in sub-frame 0. Note 7: 100 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 88 resource blocks (RB0–RB43 and RB56–RB99) are allocated in sub-frame 0. Note 8: Given per component carrier per codeword. |
A.3.3.3.2 Four antenna ports (CSI-RS)
The reference measurement channels in Table A.3.3.3.2-1 apply for verifying demodulation performance for UE-specific reference symbols with two cell-specific antenna ports and four CSI-RS antenna ports.
Table A.3.3.3.2-1: Fixed Reference Channel for CDM-multiplexed DM RS with four CSI-RS antenna ports
Parameter |
Unit |
Value |
||||||||||
Reference channel |
R.43 FDD |
R.43-1 FDD |
R.43-2 FDD |
R.50 FDD |
R.48 FDD |
R.66 FDD |
R.75 FDD |
R.75A FDD |
R.cc FDD |
R.45A-1 FDD |
R.102 FDD |
|
Channel bandwidth |
MHz |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
Allocated resource blocks |
50 (Note 3) |
50 (Note 3) |
50 (Note 5) |
50 (Note 3) |
50 (Note 3) |
50 (Note 3) |
50 (Note 3) |
50 (Note 3) |
50 (Note 3) |
50 (Note 3) |
50 (Note 3) |
|
Allocated subframes per Radio Frame |
9 |
9 |
9 |
9 |
9 |
9 |
9 |
9 |
9 |
9 |
9 |
|
Modulation |
QPSK |
QPSK |
QPSK |
64QAM |
QPSK |
256QAM |
16QAM |
16QAM |
16QAM |
16QAM |
1024QAM |
|
Target Coding Rate |
1/3 |
1/3 |
1/3 |
1/2 |
0.77 |
0.57 |
0.51 |
0.64 |
1/2 |
3/4 |
||
Information Bit Payload |
||||||||||||
For Sub-Frames 1,4,6,9 |
Bits |
3624 |
3624 |
3624 |
18336 |
6200 |
36696 |
25456 |
25456 |
15264 |
11448 |
52752 |
For Sub-Frames 2,3,7,8 |
Bits |
3624 |
3624 |
3624 |
16416 |
6200 |
35160 |
25456 |
25456 |
15264 |
11448 |
52752 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
2984 |
2984 |
3368 |
14688 |
4968 |
30576 |
21384 |
21384 |
12576 |
9528 |
N/A |
Number of Code Blocks (Note 4) |
||||||||||||
For Sub-Frames 1,4,6,9 |
Code blocks |
1 |
1 |
1 |
3 |
2 |
6 |
5 |
5 |
3 |
2 |
9 |
For Sub-Frames 2,3,7,8 |
Code blocks |
1 |
1 |
1 |
3 |
2 |
6 |
5 |
5 |
3 |
2 |
9 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
1 |
1 |
1 |
3 |
1 |
5 |
4 |
4 |
3 |
2 |
N/A |
Binary Channel Bits |
||||||||||||
For Sub-Frames 1,6 |
Bits |
12000 |
13200 |
13200 |
36000 |
12000 |
48000 |
43200 |
48000 |
24000 |
24000 |
66000 |
For Sub-Frames 4,9 |
Bits |
12000 |
12000 |
12000 |
36000 |
12000 |
48000 |
43200 |
48000 |
24000 |
24000 |
66000 |
For Sub-Frames 2,7 |
Bits |
11600 |
12800 |
12800 |
34800 |
11600 |
46400 |
41600 |
46400 |
23200 |
23200 |
64000 |
For Sub-Frames 3,8 |
Bits |
11600 |
12800 |
12800 |
34800 |
12000 |
46400 |
41600 |
46400 |
23200 |
23200 |
66000 |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
9840 |
9840 |
10560 |
29520 |
9840 |
39360 |
35424 |
40224 |
19680 |
19680 |
N/A |
Max. Throughput averaged over 1 frame |
Mbps |
3.1976 |
3.1976 |
3.236 |
15.3696 |
5.4568 |
31.800 |
22.503 |
22.503 |
13.4688 |
10.1112 |
46.5832 |
UE Category |
≥ 1 |
≥ 1 |
≥ 1 |
≥ 2 |
≥ 1 |
11-12 |
≥ 5 |
≥ 5 |
≥ 2 |
≥ 2 |
TBD |
|
UE DL Category |
≥ 6 |
≥ 6 |
≥ 6 |
≥ 6 |
≥ 6 |
≥ 11 |
≥ 6 |
≥ 6 |
≥ 6 |
≥ 6 |
20, ≥ 22 |
|
Note 1: 2 symbols allocated to PDCCH. 1 symbol allocated to PDCCH for reference channel with 1024QAM. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: 50 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 41 resource blocks (RB0–RB20 and RB30–RB49) are allocated in sub-frame 0. Note 4: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). Note 5: 50 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 47 resource blocks (RB0–RB23 and RB27–RB49) are allocated in sub-frame 0. In sub-frame 0, PDSCH is rate matched around RB22, RB23 and RB27. |
The reference measurement channels in Table A.3.3.3.2-2 apply for verifying FDD PMI accuracy measurement and CRI accuracy measurement with two CRS antenna ports and four CSI-RS antenna ports.
Table A.3.3.3.2-2: Fixed Reference Channel for four antenna ports (CSI-RS)
Parameter |
Unit |
Value |
|||||||||||||||
Reference channel |
R.44 FDD |
R.45 FDD |
R.45-1 FDD |
R.60 FDD |
R.50A -1 FDD |
R.45A-2 FDD |
|||||||||||
Channel bandwidth |
MHz |
10 |
10 |
10 |
10 |
10 |
10 |
||||||||||
Allocated resource blocks |
503 |
503 |
39 |
503 |
503 |
503 |
|||||||||||
Allocated subframes per Radio Frame |
10 |
10 |
10 |
10 |
7 |
10 |
|||||||||||
Modulation |
QPSK |
16QAM |
16QAM |
QPSK |
64QAM |
16QAM |
|||||||||||
Target Coding Rate |
1/3 |
1/2 |
1/2 |
1/2 |
1/2 |
1/2 |
|||||||||||
Information Bit Payload |
|||||||||||||||||
For Sub-Frames (Non CSI-RS subframe) |
Bits |
3624 |
11448 |
8760 |
6200 |
18336 |
11448 |
||||||||||
For Sub-Frames (CSI-RS subframe) |
Bits |
3624 |
11448 |
8760 |
6200 |
N/A |
11448 |
||||||||||
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
||||||||||
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
||||||||||
For Sub-Frame 0 |
Bits |
2984 |
9528 |
8760 |
N/A |
14688 |
9528 |
||||||||||
Number of Code Blocks per Sub-Frame |
|||||||||||||||||
For Sub-Frames (Non CSI-RS subframe) |
1 |
2 |
2 |
2 |
3 |
2 |
|||||||||||
For Sub-Frames (CSI-RS subframe) |
1 |
2 |
2 |
2 |
N/A |
2 |
|||||||||||
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
||||||||||
For Sub-Frame 5 |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
|||||||||||
For Sub-Frame 0 |
1 |
2 |
2 |
N/A |
3 |
2 |
|||||||||||
Binary Channel Bits Per Sub-Frame |
|||||||||||||||||
For Sub-Frames (Non CSI-RS subframe) |
Bits |
12000 |
24000 |
18720 |
12000 |
36000 |
24000 |
||||||||||
For Sub-Frames (CSI-RS subframe) |
Bits |
11600 |
23200 |
18096 |
11600 |
N/A |
23600 |
||||||||||
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
||||||||||
For Sub-Frame 5 |
Bits |
N/A |
N/A |
N/A |
N/A |
N/A |
N/A |
||||||||||
For Sub-Frame 0 |
Bits |
9840 |
19680 |
18720 |
N/A |
29520 |
19680 |
||||||||||
Max. Throughput averaged over 1 frame |
Mbps |
3.1976 |
10.1112 |
7.884 |
4.96 |
12.4704 |
10.1112 |
||||||||||
UE Category |
≥ 1 |
≥ 2 |
≥ 1 |
≥ 1 |
≥ 2 |
≥ 2 |
|||||||||||
Note 1: 2 symbols allocated to PDCCH for 20 MHz, 15 MHz and 10 MHz channel BW; 3 symbols allocated to PDCCH for 5 MHz and 3 MHz; 4 symbols allocated to PDCCH for 1.4 MHz Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4] Note 3: For R.44, R.45 and R.60, 50 resource blocks are allocated in sub-frames 1,2,3,4,6,7,8,9 and 41 resource blocks (RB0–RB20 and RB30–RB49) are allocated in sub-frame 0. For R.45-1, 39 resource blocks are allocated in all subframes (RB0–RB20 and RB30–RB47). For R.50A-1, 50 resource blocks are allocated in sub-frames 2, 3, 4, 7, 8, 9 and 41 resource blocks (RB0–RB20 and RB30–RB49) are allocated in sub-frame 0. Note 4: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit) |
The reference measurement channels in Table A.3.3.3.2-3 apply for verifying demodulation performance for UE-specific reference symbols with two cell-specific antenna ports and four CSI-RS antenna ports.
Table A.3.3.3.2-3: Fixed Reference Channel for CDM-multiplexed DM RS with four CSI-RS antenna ports
Parameter |
Unit |
Value |
Reference channel |
R.64 FDD |
|
Channel bandwidth |
MHz |
10 |
Allocated resource blocks (Note 4) |
6 |
|
Allocated subframes per 4 Radio Frames |
15 |
|
Modulation |
QPSK |
|
Target Coding Rate |
1/3 |
|
Information Bit Payload |
||
For Sub-Frames 0,1,4,5,6,9 (Note 3) |
Bits |
504 |
For Sub-Frames 2,3,7,8 (Note 3) |
Bits |
504 |
Number of Code Blocks |
||
For Sub-Frames 0,1,4,5,6,9 |
Code blocks |
1 |
For Sub-Frames 2,3,7,8 |
Code blocks |
1 |
Binary Channel Bits |
||
For Sub-Frames 0,1,4,5,6,9 |
Bits |
1440 |
For Sub-Frames 2,3,7,8 |
Bits |
1392 |
Max. Throughput averaged over 4 frames |
Mbps |
0.189 |
UE DL Category |
0 |
|
Note 1: 2 symbols allocated to PDCCH. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: The downlink subframes are scheduled at the 0th, 1st, 2nd, 8th, 9th, 10th, 16th, 17th, 18th, 24th, 25th, 26th, 32nd, 33rd, 34th subframes every 40ms. Information bit payload is avaialbe if downlink subframe is scheduled. Note 4: Allocated PRB positions start from {9, 10, …, 9+N-1}, where N is the number of allocated resource blocks. |
The reference measurement channels in Table A.3.3.3.2-4 apply with two CRS antenna ports and four CSI-RS antenna ports.
Table A.3.3.3.2-4: Fixed Reference Channel for four antenna ports (CSI-RS)
Parameter |
Unit |
Value |
Reference channel |
R.69 FDD |
|
Channel bandwidth |
MHz |
10 |
Allocated resource blocks |
50 |
|
Allocated subframes per Radio Frame |
8 |
|
Modulation |
QPSK |
|
Target Coding Rate |
||
For Sub-Frames 2,3,4,6,7,8,9 |
0.74 |
|
For Sub-Frame 1 |
0.8 |
|
Information Bit Payload |
||
For Sub-Frames 2,3,4,6,7,8,9 |
Bits |
7992 |
For Sub-Frame 1 |
Bits |
7992 |
For Sub-Frame 5 |
Bits |
N/A |
For Sub-Frame 0 |
Bits |
N/A |
Number of Code Blocks per Sub-Frame |
||
For Sub-Frames 2,3,4,6,7,8,9 |
2 |
|
For Sub-Frame 1 |
2 |
|
For Sub-Frame 5 |
N/A |
|
For Sub-Frame 0 |
N/A |
|
Binary Channel Bits Per Sub-Frame |
||
For Sub-Frames 2,3,4,6,7,8,9 |
Bits |
10800 |
For Sub-Frame 1 |
Bits |
10000 |
2 For Sub-Frame 5 |
Bits |
N/A |
For Sub-Frame 0 |
Bits |
N/A |
Max. Throughput averaged over 1 frame |
Mbps |
6.3936 |
UE Category |
≥ 1 |
|
Note 1: 3 symbols allocated to PDCCH. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4] Note 3: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit) |
The reference measurement channels in Table A.3.3.3.2-5 apply with two CRS antenna ports and four CSI-RS antenna ports.
Table A.3.3.3.2-5: Fixed Reference Channel for CDM-multiplexed DM RS with four CSI-RS antenna ports with ZP CSI-RS and NZP CSI-RS
Parameter |
Unit |
Value |
||
Reference channel |
R.98 FDD |
R.99 FDD |
||
Channel bandwidth |
MHz |
10 |
10 |
|
Allocated resource blocks |
50 (Note 3) |
50 (Note 3) |
||
Allocated subframes per Radio Frame |
9 |
9 |
||
Modulation |
16QAM |
16QAM |
||
Target Coding Rate |
1/2 |
1/2 |
||
Information Bit Payload |
||||
For Sub-Frames 1,3,4,6,8,9 |
Bits |
22920 |
11448 |
|
For Sub-Frames 2,7 |
Bits |
22920 |
11448 |
|
For Sub-Frame 5 |
Bits |
n/a |
n/a |
|
For Sub-Frame 0 |
Bits |
19080 |
9528 |
|
Number of Code Blocks (Note 4) |
||||
For Sub-Frames 1,3,4,6,8,9 |
Code blocks |
4 |
2 |
|
For Sub-Frames 2, 7 |
Code blocks |
4 |
2 |
|
For Sub-Frame 5 |
Bits |
n/a |
n/a |
|
For Sub-Frame 0 |
Bits |
4 |
2 |
|
Binary Channel Bits |
||||
For Sub-Frames 1,3,4,6,8,9 |
Bits |
43200 |
21600 |
|
For Sub-Frames 2,7 |
38400 |
19200 |
||
For Sub-Frame 5 |
Bits |
n/a |
n/a |
|
For Sub-Frame 0 |
Bits |
35424 |
17712 |
|
Max. Throughput averaged over 1 frame |
Mbps |
20.244 |
10.1112 |
|
Note 1: 2 symbols allocated to PDCCH. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: 50 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 41 resource blocks (RB0–RB20 and RB30–RB49) are allocated in sub-frame 0. Note 4: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). |
The reference measurement channels in Table A.3.3.3.2-6 apply with four CRS antenna ports and four CSI-RS antenna ports.
Table A.3.3.3.2-6: Fixed Reference Channel for CDM-multiplexed DM RS with four CSI-RS antenna ports with ZP CSI-RS and NZP CSI-RS
Parameter |
Unit |
Value |
Reference channel |
R.100 FDD |
|
Channel bandwidth |
MHz |
10 |
Allocated resource blocks |
50 (Note 3) |
|
Allocated subframes per Radio Frame |
9 |
|
Modulation |
16QAM |
|
Target Coding Rate |
1/2 |
|
Information Bit Payload |
||
For Sub-Frames 1,3,4,6,8,9 |
Bits |
22920 |
For Sub-Frames 2,7 |
Bits |
22920 |
For Sub-Frame 5 |
Bits |
n/a |
For Sub-Frame 0 |
Bits |
19080 |
Number of Code Blocks (Note 4) |
||
For Sub-Frames 1,3,4,6,8,9 |
Code blocks |
4 |
For Sub-Frames 2, 7 |
Code blocks |
4 |
For Sub-Frame 5 |
Bits |
n/a |
For Sub-Frame 0 |
Bits |
4 |
Binary Channel Bits |
||
For Sub-Frames 1,3,4,6,8,9 |
Bits |
41600 |
For Sub-Frames 2,7 |
36800 |
|
For Sub-Frame 5 |
Bits |
n/a |
For Sub-Frame 0 |
Bits |
34112 |
Max. Throughput averaged over 1 frame |
Mbps |
20.244 |
Note 1: 2 symbols allocated to PDCCH. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: 50 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 41 resource blocks (RB0–RB20 and RB30–RB49) are allocated in sub-frame 0. Note 4: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). |
A.3.3.3.2A Eight antenna ports (CSI-RS)
The reference measurement channels in Table A.3.3.3.2A-1 apply for verifying FDD CRI accuracy measurement with two CRS antenna ports and eight CSI-RS antenna ports.
Table A.3.3.3.2A-1: Fixed Reference Channel for eight antenna ports (CSI-RS)
Parameter |
Unit |
Value |
|
Reference channel |
R.50A-2 FDD |
R.50A-3 FDD |
|
Channel bandwidth |
MHz |
10 |
10 |
Allocated resource blocks |
503 |
503 |
|
Allocated subframes per Radio Frame |
7 |
5 |
|
Modulation |
64QAM |
64QAM |
|
Target Coding Rate |
1/2 |
1/2 |
|
Information Bit Payload |
|||
For Sub-Frames (Non CSI-RS subframe) |
Bits |
18336 |
18336 |
For Sub-Frames (CSI-RS subframe) |
Bits |
N/A |
N/A |
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
N/A |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
14688 |
14688 |
Number of Code Blocks per Sub-Frame |
|||
For Sub-Frames (Non CSI-RS subframe) |
3 |
3 |
|
For Sub-Frames (CSI-RS subframe) |
N/A |
N/A |
|
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
N/A |
For Sub-Frame 5 |
N/A |
N/A |
|
For Sub-Frame 0 |
3 |
3 |
|
Binary Channel Bits Per Sub-Frame |
|||
For Sub-Frames (Non CSI-RS subframe) |
Bits |
36000 |
36000 |
For Sub-Frames (CSI-RS subframe) |
Bits |
N/A |
N/A |
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
N/A |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
29520 |
29520 |
Max. Throughput averaged over 1 frame |
Mbps |
12.4704 |
8.8032 |
UE Category |
≥ 2 |
≥ 2 |
|
Note 1: 2 symbols allocated to PDCCH for 20 MHz, 15 MHz and 10 MHz channel BW; 3 symbols allocated to PDCCH for 5 MHz and 3 MHz; 4 symbols allocated to PDCCH for 1.4 MHz Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4] Note 3: For R.50A-2, 50 resource blocks are allocated in sub-frames 2, 3, 4, 7, 8, 9 and 41 resource blocks (RB0–RB20 and RB30–RB49) are allocated in sub-frame 0. For R.50A-3, 50 resource blocks are allocated in sub-frames 3, 4, 8, 9 and 41 resource blocks (RB0–RB20 and RB30–RB49) are allocated in sub-frame 0. Note 4: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit) |
Table A.3.3.3.2A-2: Fixed Reference Channel for eight antenna ports (CSI-RS)
Parameter |
Unit |
Value |
Reference channel |
R.108 FDD |
|
Channel bandwidth |
MHz |
10 |
Allocated resource blocks |
43 |
|
Allocated subframes per Radio Frame |
8 |
|
Modulation |
QPSK |
|
Target Coding Rate |
1/2 |
|
Information Bit Payload |
||
For Sub-Frames (Non CSI-RS subframe) |
Bits |
472 |
For Sub-Frames (CSI-RS subframe) |
Bits |
472 |
For Sub-Frame 5,7 |
Bits |
N/A |
Number of Code Blocks per Sub-Frame |
||
For Sub-Frames (Non CSI-RS subframe) |
1 |
|
For Sub-Frames (CSI-RS subframe) |
1 |
|
For Sub-Frame 5,7 |
N/A |
|
Binary Channel Bits Per Sub-Frame |
||
For Sub-Frames (Non CSI-RS subframe) |
Bits |
960 |
For Sub-Frames (CSI-RS subframe) |
Bits |
896 |
For Sub-Frame 5,7 |
Bits |
N/A |
Max. Throughput averaged over 1 frame |
Mbps |
0.3776 |
UE Category |
≥ 1 |
|
Note 1: 2 symbols allocated to PDCCH. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4] Note 3: Allocated PRB positions for PDSCH are {2, 3, 4, 5} within the assigned narrowband. Allocated PRB positions for MPDCCH are {0, 1} within the assigned narrowband. Note 4: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit) |
A.3.3.3.3 Twelve antenna port (CSI-RS)
The reference measurement channels in Table A.3.3.3.3-1 apply for verifying PMI accuracy performance for UE-specific reference symbols with two cell-specific antenna ports and twelve CSI-RS antenna ports.
Table A.3.3.3.3-1: Fixed Reference Channel for CDM-multiplexed DM RS with twelve CSI-RS antenna ports
Parameter |
Unit |
Value |
Reference channel |
R.77 FDD |
|
Channel bandwidth |
MHz |
10 |
Allocated resource blocks |
50 (Note 3) |
|
Allocated subframes per Radio Frame |
9 |
|
Modulation |
64QAM |
|
Target Coding Rate |
1/2 |
|
Information Bit Payload |
||
For Sub-Frames (Non CSI-RS subframe) |
Bits |
18336 |
For Sub-Frames (CSI-RS subframe) |
Bits |
16416 |
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
For Sub-Frame 5 |
Bits |
N/A |
For Sub-Frame 0 |
14688 |
|
Number of Code Blocks per Sub-Frame |
Code blocks |
|
For Sub-Frames (Non CSI-RS subframe) |
Code blocks |
3 |
For Sub-Frames (CSI-RS subframe) |
Bits |
3 |
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
For Sub-Frame 5 |
N/A |
|
For Sub-Frame 0 |
Bits |
3 |
Binary Channel Bits Per Sub-Frame |
||
For Sub-Frames (Non CSI-RS subframe) |
36000 |
|
For Sub-Frames (CSI-RS subframe) |
Bits |
32400 |
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
For Sub-Frame 5 |
Bits |
N/A |
For Sub-Frame 0 |
Bits |
29520 |
Max. Throughput averaged over 1 frame |
Mbps |
15.7536 |
UE Category |
≥ 2 |
|
Note 1: 2 symbols allocated to PDCCH. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: 50 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 41 resource blocks (RB0–RB20 and RB30–RB49) are allocated in sub-frame 0. Note 4: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). |
A.3.3.3.4 Sixteen antenna port (CSI-RS)
The reference measurement channels in Table A.3.3.3.4-1 apply for verifying PMI accuracy performance for UE-specific reference symbols with two cell-specific antenna ports and sixteen CSI-RS antenna ports.
Table A.3.3.3.4-1: Fixed Reference Channel for CDM-multiplexed DM RS with sixteen CSI-RS antenna ports
Paramter |
Unit |
Value |
Reference channel |
R.78 FDD |
|
Channel bandwidth |
MHz |
10 |
Allocated resource blocks |
50 (Note 3) |
|
Allocated subframes per Radio Frame |
9 |
|
Modulation |
16QAM |
|
Target Coding Rate |
1/2 |
|
Information Bit Payload |
||
For Sub-Frames (Non CSI-RS subframe) |
Bits |
11448 |
For Sub-Frames (CSI-RS subframe) |
Bits |
9912 |
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
For Sub-Frame 5 |
Bits |
N/A |
For Sub-Frame 0 |
9528 |
|
Number of Code Blocks per Sub-Frame |
Code blocks |
|
For Sub-Frames (Non CSI-RS subframe) |
Code blocks |
2 |
For Sub-Frames (CSI-RS subframe) |
Bits |
2 |
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
For Sub-Frame 5 |
N/A |
|
For Sub-Frame 0 |
Bits |
2 |
Binary Channel Bits Per Sub-Frame |
||
For Sub-Frames (Non CSI-RS subframe) |
24000 |
|
For Sub-Frames (CSI-RS subframe) |
Bits |
20800 |
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
For Sub-Frame 5 |
Bits |
N/A |
For Sub-Frame 0 |
Bits |
19680 |
Max. Throughput averaged over 1 frame |
Mbps |
9.804 |
UE Category |
≥ 2 |
|
Note 1: 2 symbols allocated to PDCCH. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: 50 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 41 resource blocks (RB0–RB20 and RB30–RB49) are allocated in sub-frame 0. Note 4: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). |
A.3.3.3.5 Twenty-four antenna port (CSI-RS)
The reference measurement channels in Table A.3.3.3.5-1 apply for verifying PMI accuracy performance for UE-specific reference symbols with two cell-specific antenna ports and twenty-four CSI-RS antenna ports.
Table A.3.3.3.5-1: Fixed Reference Channel for CDM-multiplexed DM RS with twenty-four CSI-RS antenna ports
Parameter |
Unit |
Value |
|
Reference channel |
R.88 FDD |
R.88A FDD |
|
Channel bandwidth |
MHz |
10 |
10 |
Allocated resource blocks |
50 (Note 3) |
50 (Note 3) |
|
Allocated subframes per Radio Frame |
9 |
9 |
|
Modulation |
16QAM |
16QAM |
|
Target Coding Rate |
1/2 |
1/2 |
|
Information Bit Payload |
|||
For Sub-Frames (Non CSI-RS subframe) |
Bits |
11448 |
11448 |
For Sub-Frames (CSI-RS subframe) |
Bits |
9912 |
11448 |
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
N/A |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
For Sub-Frame 0 |
9528 |
9528 |
|
Number of Code Blocks per Sub-Frame |
Code blocks |
||
For Sub-Frames (Non CSI-RS subframe) |
Code blocks |
2 |
2 |
For Sub-Frames (CSI-RS subframe) |
Bits |
2 |
2 |
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
N/A |
For Sub-Frame 5 |
N/A |
N/A |
|
For Sub-Frame 0 |
Bits |
2 |
2 |
Binary Channel Bits Per Sub-Frame |
|||
For Sub-Frames (Non CSI-RS subframe) |
24000 |
24000 |
|
For Sub-Frames (CSI-RS subframe) |
Bits |
19200 |
22400 |
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
N/A |
For Sub-Frame 5 |
Bits |
N/A |
N/A |
For Sub-Frame 0 |
Bits |
19680 |
19680 |
Max. Throughput averaged over 1 frame |
Mbps |
9.804 |
10.1112 |
UE Category |
≥ 2 |
≥ 2 |
|
Note 1: 2 symbols allocated to PDCCH. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: 50 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 41 resource blocks (RB0–RB20 and RB30–RB49) are allocated in sub-frame 0. Note 4: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). |
A.3.3.3.6 Thirty-two antenna port (CSI-RS)
The reference measurement channels in Table A.3.3.3.6-1 apply for verifying PMI accuracy performance for UE-specific reference symbols with two cell-specific antenna ports and thirty-two CSI-RS antenna ports.
Table A.3.3.3.6-1: Fixed Reference Channel for CDM-multiplexed DM RS with thirty-two CSI-RS antenna ports
Paramter |
Unit |
Value |
Reference channel |
R.89 FDD |
|
Channel bandwidth |
MHz |
10 |
Allocated resource blocks |
50 (Note 3) |
|
Allocated subframes per Radio Frame |
9 |
|
Modulation |
64QAM |
|
Target Coding Rate |
1/2 |
|
Information Bit Payload |
||
For Sub-Frames (Non CSI-RS subframe) |
Bits |
18336 |
For Sub-Frames (CSI-RS subframe) |
Bits |
15264 |
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
For Sub-Frame 5 |
Bits |
N/A |
For Sub-Frame 0 |
14688 |
|
Number of Code Blocks per Sub-Frame |
Code blocks |
|
For Sub-Frames (Non CSI-RS subframe) |
Code blocks |
3 |
For Sub-Frames (CSI-RS subframe) |
Bits |
3 |
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
For Sub-Frame 5 |
N/A |
|
For Sub-Frame 0 |
Bits |
3 |
Binary Channel Bits Per Sub-Frame |
||
For Sub-Frames (Non CSI-RS subframe) |
36000 |
|
For Sub-Frames (CSI-RS subframe) |
Bits |
26400 |
For Sub-Frames (ZeroPowerCSI-RS subframe) |
Bits |
N/A |
For Sub-Frame 5 |
Bits |
N/A |
For Sub-Frame 0 |
Bits |
29520 |
Max. Throughput averaged over 1 frame |
Mbps |
15.5232 |
UE Category |
≥ 2 |
|
Note 1: 2 symbols allocated to PDCCH. Note 2: Reference signal, synchronization signals and PBCH allocated as per TS 36.211 [4]. Note 3: 50 resource blocks are allocated in sub-frames 1, 2, 3, 4, 6, 7, 8, 9 and 41 resource blocks (RB0–RB20 and RB30–RB49) are allocated in sub-frame 0. Note 4: If more than one Code Block is present, an additional CRC sequence of L = 24 Bits is attached to each Code Block (otherwise L = 0 Bit). |