9.3.7 Minimum requirement PUSCH 3-2

36.1013GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Release 18TSUser Equipment (UE) radio transmission and reception

9.3.7.1 FDD

For the parameters specified in Table 9.3.7.1-1, and using the downlink physical channels specified in Annex C.3.2, the minimum requirements are specified in Table 9.3.7.1-2 and by the following.

a) the ratio of the throughput obtained when transmitting based on UE PUSCH 3-2 reported wideband CQI and subband PMI and that obtained when transmitting based on PUSCH 3-1 reported wideband CQI and wideband PMI shall be ≥

b) The ratio of the throughput obtained when transmitting on a randomly selected sub-band among the sub-bands with the highest differential CQI offset level the corresponding TBS based on UE PUSCH3-2 reported subband CQI and subband PMI and that obtained when transmitting on a randomly selected sub-band in set S based on PUSCH 1-2 reported wideband CQI and subband PMI shall be ≥

The transport block sizes TBS for wideband CQI and subband CQI are selected according to RC.17 FDD for test 1 and according to RC.18 FDD for test 2.

Table 9.3.7.1-1 Sub-band test for FDD

Parameter

Unit

Test 1

Test 2

Bandwidth

MHz

10MHz

PDSCH resource allocation

RB

50PRB

a subband, 6PRB

Transmission mode

TM6

TM9

Downlink power allocation

dB

-6

0

dB

-6

0

dB

–

-3

σ

dB

3

-3

SNR (Note 3)

dB

0

1

5

6

dB[mW/15kHz]

-98

-97

-93

-92

dB[mW/15kHz]

-98

-98

-98

-98

Propagation channel

EVA5

EVA5

Antenna configuration

4×2 ULA low

4×2 XP high (Note 4)

Beamforming Model

–

B.4.3

CRS reference signals

Antenna ports 0, 1, 2, 3

Antenna ports 0, 1

Time offset between TX antenna (Note 5)

ns

65

–

CSI reference signals

Antenna ports 15, 16, 17, 18

CSI-RS periodicity and subframe offset

TCSI-RS / ∆CSI-RS

–

5/ 1

CSI-RS reference signal configuration

–

4

alternativeCodebookEnabledFor4TX

No

Yes

CodeBookSubsetRestriction bitmap

0x0000 0000 0000 FFFF

0x0000 0000 0000 FFFF 0000 FFFF

Reporting interval (Note 6)

ms

5

5

CQI delay

ms

8

8

Reporting mode

PUSCH 3-2, PUSCH 3-1

PUSCH 3-2, PUSCH 1-2

Sub-band size

RB

6 (full size)

6 (full size)

Max number of HARQ transmissions

1

1

Note 1: If the UE reports in an available uplink reporting instance at subframe SF#n based on CQI estimation at a downlink subframe not later than SF#(n-4), this reported subband or wideband CQI cannot be applied at the eNB downlink before SF#(n+4)

Note 2: Reference measurement channel RC.17 FDD / RC.18 FDD for Test 1 / 2 according to Table A.4-1 with one/two sided dynamic OCNG Pattern OP.1/2 FDD as described in Annex A.5.1.1/2.

Note 3: For each test, the minimum requirements shall be fulfilled for at least one of the two SNR(s) and the respective wanted signal input level.

Note 4: Randomization of the principle beam direction shall be used as specified in B.2.3A.4.

Note 5: The values of time offset are [0ns 65ns 0ns 65ns] for antenna port [0, 1, 2, 3] respectively.

Note 6: PDCCH DCI format 0 with a trigger for aperiodic CQI shall be transmitted in downlink SF#1 and #6 to allow aperiodic CQI/PMI/RI to be transmitted in uplink SF#0 and #5.

Table 9.3.7.1-2 Minimum requirement (FDD)

Test 1

Test 2

α

1.05

–

β

–

1.15

UE Category

≥2

≥2

9.3.7.2 TDD

For the parameters specified in Table 9.3.7.2-1, and using the downlink physical channels specified in Annex C.3.2, the minimum requirements are specified in Table 9.3.7.2-2 and by the following.

a) the ratio of the throughput obtained when transmitting based on UE PUSCH 3-2 reported wideband CQI and subband PMI and that obtained when transmitting based on PUSCH 3-1 reported wideband CQI and wideband PMI shall be ≥

b) The ratio of the throughput obtained when transmitting on a randomly selected sub-band among the sub-bands with the highest differential CQI offset level the corresponding TBS based on UE PUSCH3-2 reported subband CQI and subband PMI and that obtained when transmitting on a randomly selected sub-band in set S based on PUSCH 1-2 reported wideband CQI and subband PMI shall be ≥

The transport block sizes TBS for wideband CQI and subband CQI are selected according to RC.17 TDD for test 1 and RC.18 TDD for test 2.

Table 9.3.7.2-1 Sub-band test for TDD

Parameter

Unit

Test 1

Test 2

Bandwidth

MHz

10MHz

PDSCH resource allocation

RB

50PRB

a subband, 6PRB

Transmission mode

TM6

TM9

Uplink downlink configuration

1

1

Special subframe configuration

4

4

Downlink power allocation

dB

-6

0

dB

-6

0

dB

–

-3

σ

dB

3

-3

SNR (Note 3)

dB

0

1

5

6

dB[mW/15kHz]

-98

-97

-93

-92

dB[mW/15kHz]

-98

-98

-98

-98

Propagation channel

EVA5

EVA5

Antenna configuration

4×2 ULA low

4×2 XP high (Note 4)

Beamforming Model

–

B.4.3

CRS reference signals

Antenna ports 0, 1, 2, 3

Antenna ports 0, 1

Time offset between TX antenna (Note 5)

ns

65

–

CSI reference signals

Antenna ports 15, 16, 17, 18

CSI-RS periodicity and subframe offset

TCSI-RS / ∆CSI-RS

–

5/ 4

CSI-RS reference signal configuration

–

4

alternativeCodebookEnabledFor4TX

No

Yes

CodeBookSubsetRestriction bitmap

0x0000 0000 0000 FFFF

0x0000 0000 0000 FFFF 0000 FFFF

Reporting interval (Note 6)

ms

5

5

CQI delay

ms

8

8

Reporting mode

PUSCH 3-2, PUSCH 3-1

PUSCH 3-2, PUSCH 1-2

Sub-band size

RB

6 (full size)

6 (full size)

Max number of HARQ transmissions

1

1

Note 1: If the UE reports in an available uplink reporting instance at subframe SF#n based on CQI estimation at a downlink subframe not later than SF#(n-4), this reported subband or wideband CQI cannot be applied at the eNB downlink before SF#(n+4)

Note 2: Reference measurement channel RC.17 TDD / RC.18 TDD for Test 1 / 2 according to Table A.4-1 with one/two sided dynamic OCNG Pattern OP.1/2 TDD as described in Annex A.5.2.1/2.

Note 3: For each test, the minimum requirements shall be fulfilled for at least one of the two SNR(s) and the respective wanted signal input level.

Note 4: Randomization of the principle beam direction shall be used as specified in B.2.3A.4.

Note 5: The values of time offset are [0ns 65ns 0ns 65ns] for antenna port [0, 1, 2, 3] respectively.

Note 6: PDCCH DCI format 0 with a trigger for aperiodic CQI shall be transmitted in downlink SF#4 and #9 to allow aperiodic CQI/PMI/RI to be transmitted in uplink SF#3 and #8.

Table 9.3.7.2-2 Minimum requirement (TDD)

Test 1

Test 2

α

1.05

–

β

–

1.15

UE Category

≥2

≥2