9.2.1 Minimum requirement PUCCH 1-0 (Cell-Specific Reference Symbols)

36.1013GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Release 18TSUser Equipment (UE) radio transmission and reception

Tools: ARFCN - Frequency Conversion for 5G NR/LTE/UMTS/GSM

9.2.1.1 FDD

The following requirements apply to UE Category ≥1. For the parameters specified in Table 9.2.1.1-1 and Table 9.2.1.1-2, and using the downlink physical channels specified in tables C.3.2-1 and C.3.2-2, the reported CQI value according to RC.1 FDD / RC.14 FDD in Table A.4-1 shall be in the range of ±1 of the reported median more than 90% of the time. If the PDSCH BLER using the transport format indicated by median CQI is less than or equal to 0.1, the BLER using the transport format indicated by the (median CQI + 1) shall be greater than 0.1. If the PDSCH BLER using the transport format indicated by the median CQI is greater than 0.1, the BLER using transport format indicated by (median CQI – 1) shall be less than or equal to 0.1.

The applicability of the requirement with 5MHz bandwidth as specificed in Table 9.2.1.1-2 is defined in 9.1.1.1.

Table 9.2.1.1-1: PUCCH 1-0 static test (FDD)

Parameter		Unit	Test 1		Test 2
Bandwidth		MHz	10
PDSCH transmission mode			1
Downlink power allocation		dB	0
		dB	0
	σ	dB	0
Propagation condition and antenna configuration			AWGN (1 x 2)
SNR (Note 2)		dB	0	1	6	7
		dB[mW/15kHz]	-98	-97	-92	-91
		dB[mW/15kHz]	-98		-98
Max number of HARQ transmissions			1
Physical channel for CQI reporting			PUCCH Format 2
PUCCH Report Type			4
Reporting periodicity		ms	N_pd = 5
cqi-pmi-ConfigurationIndex			6
Note 1: Reference measurement channel RC.1 FDD according to Table A.4-1 with one sided dynamic OCNG Pattern OP.1 FDD as described in Annex A.5.1.1, except for category 1 UE use RC.4 FDD with two sided dynamic OCNG Pattern OP.2 FDD as described in Annex A.5.1.2. Note 2: For each test, the minimum requirements shall be fulfilled for at least one of the two SNR(s) and the respective wanted signal input level.

Table 9.2.1.1-2: PUCCH 1-0 static test (FDD 5MHz)

Parameter		Unit	Test 1		Test 2
Bandwidth		MHz	5
PDSCH transmission mode			1
Downlink power allocation		dB	0
		dB	0
	σ	dB	0
Propagation condition and antenna configuration			AWGN (1 x 2)
SNR (Note 2)		dB	[0]	[1]	[6]	[7]
		dB[mW/15kHz]	[-98]	[-97]	[-92]	[-91]
		dB[mW/15kHz]	-98		-98
Max number of HARQ transmissions			1
Physical channel for CQI reporting			PUCCH Format 2
PUCCH Report Type			4
Reporting periodicity		ms	N_pd = 5
cqi-pmi-ConfigurationIndex			6
Note 1: Reference measurement channel RC.14 FDD according to Table A.4-1 with one sided dynamic OCNG Pattern OP.1 FDD as described in Annex A.5.1.1, except for category 1 UE use RC.15 FDD with two sided dynamic OCNG Pattern OP.2 FDD as described in Annex A.5.1.2. Note 2: For each test, the minimum requirements shall be fulfilled for at least one of the two SNR(s) and the respective wanted signal input level.

9.2.1.2 TDD

The following requirements apply to UE Category ≥1. For the parameters specified in Table 9.2.1.2-1, and using the downlink physical channels specified in tables C.3.2-1 and C.3.2-2, the reported CQI value according to RC.1 TDD in Table A.4-1 shall be in the range of ±1 of the reported median more than 90% of the time. If the PDSCH BLER using the transport format indicated by median CQI is less than or equal to 0.1, the BLER using the transport format indicated by the (median CQI + 1) shall be greater than 0.1. If the PDSCH BLER using the transport format indicated by the median CQI is greater than 0.1, the BLER using transport format indicated by (median CQI – 1) shall be less than or equal to 0.1.

Table 9.2.1.2-1: PUCCH 1-0 static test (TDD)

Parameter		Unit	Test 1		Test 2
Bandwidth		MHz	10
PDSCH transmission mode			1
Uplink downlink configuration			2
Special subframe configuration			4
Downlink power allocation		dB	0
		dB	0
	σ	dB	0
Propagation condition and antenna configuration			AWGN (1 x 2)
SNR (Note 2)		dB	0	1	6	7
		dB[mW/15kHz]	-98	-97	-92	-91
		dB[mW/15kHz]	-98		-98
Max number of HARQ transmissions			1
Physical channel for CQI reporting			PUSCH (Note 3)
PUCCH Report Type			4
Reporting periodicity		ms	N_pd = 5
cqi-pmi-ConfigurationIndex			3
ACK/NACK feedback mode			Multiplexing
Note 1: Reference measurement channel RC.1 TDD according to Table A.4-1 with one sided dynamic OCNG Pattern OP.1 TDD as described in Annex A.5.2.1, except for category 1 UE use RC.4 TDD with two sided dynamic OCNG Pattern OP.2 TDD as described in Annex A.5.2.2. Note 2: For each test, the minimum requirements shall be fulfilled for at least one of the two SNR(s) and the respective wanted signal input level. Note 3: To avoid collisions between CQI reports and HARQ-ACK it is necessary to report both on PUSCH instead of PUCCH. PDCCH DCI format 0 shall be transmitted in downlink SF#3 and #8 to allow periodic CQI to multiplex with the HARQ-ACK on PUSCH in uplink subframe SF#7 and #2.

9.2.1.3 FDD (CSI measurements in case two CSI subframe sets are configured)

The following requirements apply to UE Category ≥1. For the parameters specified in Table 9.2.1.3-1, and using the downlink physical channels specified in tables C.3.2-1 for Cell 1, C.3.3-1 for Cell 2 and C.3.2-2, the reported CQI value according to RC.2 FDD / RC.6 FDD in Table A.4-1 in subframes overlapping with aggressor cell ABS and non-ABS subframes shall be in the range of ±1 of the reported median more than 90% of the time. If the PDSCH BLER in non-ABS subframes using the transport format indicated by median CQI obtained by reports in CSI subframe sets C_CSI,1 is less than or equal to 0.1, the BLER in non-ABS subframes using the transport format indicated by the (median CQI + 1) shall be greater than 0.1. If the PDSCH BLER in non-ABS subframes using the transport format indicated by the median CQI is greater than 0.1, the BLER in non-ABS subframes using transport format indicated by (median CQI – 1) shall be less than or equal to 0.1. The value of the median CQI obtained by reports in CSI subframe sets C_CSI,0minus the median CQI obtained by reports in CSI subframe sets C_CSI,1shall be larger than or equal to 2 and less than or equal to 5 in Test 1 and shall be larger than or equal to 0 and less than or equal to 1 in Test 2.

Table 9.2.1.3-1: PUCCH 1-0 static test (FDD)

Parameter			Unit	Test 1				Test 2
				Cell 1			Cell 2	Cell 1		Cell 2
Bandwidth			MHz	10				10
PDSCH transmission mode				2		Note 10		2		Note 10
Downlink power allocation			dB	-3				-3
			dB	-3				-3
		σ	dB	0				0
Propagation condition and antenna configuration				Clause B.1 (2×2)				Clause B.1 (2×2)
(Note 1)			dB	4	5		6	4	5	-12
at antenna port			dBm/15kHz	-102 (Note 7)			N/A	-98(Note 7)		N/A
			dBm/15kHz	-98 (Note 8)			N/A	-98(Note 8)		N/A
			dBm/15kHz	-94.8 (Note 9)			N/A	-98(Note 9)		N/A
			dB[mW/15kHz]	-94	-93		-92	-94	-93	-110
Subframe Configuration				Non-MBSFN			Non-MBSFN	Non-MBSFN		Non-MBSFN
Cell Id				0			1	0		1
Time Offset between Cells			μs	2.5 (synchronous cells)				2.5 (synchronous cells)
ABS pattern (Note 2)				N/A			01010101 01010101 01010101 01010101 01010101	N/A		01010101 01010101 01010101 01010101 01010101
RLM/RRM Measurement Subframe Pattern (Note 4)				00000100 00000100 00000100 00000100 00000100			N/A	00000100 00000100 00000100 00000100 00000100		N/A
CSI Subframe Sets (Note 3)	C_CSI,0			01010101 01010101 01010101 01010101 01010101			N/A	01010101 01010101 01010101 01010101 01010101		N/A
	C_CSI,1			10101010 10101010 10101010 10101010 10101010			N/A	10101010 10101010 10101010 10101010 10101010		N/A
Number of control OFDM symbols				3				3
Max number of HARQ transmissions				1				1
Physical channel for C_CSI,0CQI reporting				PUCCH Format 2				PUCCH Format 2
Physical channel for C_CSI,1CQI reporting				PUSCH (Note 12)				PUSCH (Note 12)
PUCCH Report Type				4				4
Reporting periodicity			Ms	N_pd = 5				N_pd = 5
cqi-pmi-ConfigurationIndex C_CSI,0 (Note 13)				6		N/A		6		N/A
cqi-pmi-ConfigurationIndex2 C_CSI,1 (Note 14)				5		N/A		5		N/A
Note 1: For each test, the minimum requirements shall be fulfilled for at least one of the two SNR(s) and the respective wanted signal input level. Note 2: ABS pattern as defined in [9]. Note 3: Time-domain measurement resource restriction pattern for PCell measurements as defined in [7] Note 4: As configured according to the time-domain measurement resource restriction pattern for CSI measurements defined in [7] Note 5: Time-domain measurement resource restriction pattern for PCell measurements as defined in [7] Note 6: Cell 1 is the serving cell. Cell 2 is the aggressor cell. The number of the CRS ports in Cell1 and Cell2 is the same. Note 7: This noise is applied in OFDM symbols #1, #2, #3, #5, #6, #8, #9, #10,#12, #13 of a subframe overlapping with the aggressor ABS. Note 8: This noise is applied in OFDM symbols #0, #4, #7, #11 of a subframe overlapping with the aggressor ABS. Note 9: This noise is applied in all OFDM symbols of a subframe overlapping with aggressor non-ABS. Note 10: Downlink physical channel setup in Cell 2 in accordance with Annex C.3.3 applying OCNG pattern as defined in Annex A.5.1.5 Note 11: Reference measurement channel in Cell 1 RC.2 FDD according to Table A.4-1 for UE Cateogry 2-8 with one sided dynamic OCNG Pattern OP.1 FDD as described in Annex A.5.1.1, and RC.6 FDD according to Table A.4-1 for Category 1 with one/two sided dynamic OCNG Pattern OP. 1/2 FDD as described in Annex A.5.1.1 and A.5.1.2. Note 12: To avoid collisions between HARQ-ACK and wideband CQI it is necessary to report both on PUSCH instead of PUCCH. PDCCH DCI format 0 shall be transmitted in downlink SF#4 and #9 to allow periodic CQI to multiplex with the HARQ-ACK on PUSCH in uplink subframe SF#8 and #3. Note 13: cqi-pmi-ConfigurationIndex is applied for C_CSI,0. Note 14: cqi-pmi-ConfigurationIndex2 is applied for C_CSI,1.

9.2.1.4 TDD (CSI measurements in case two CSI subframe sets are configured)

The following requirements apply to UE Category ≥1. For the parameters specified in Table 9.2.1.4-1, and using the downlink physical channels specified in tables C.3.2-1 for Cell 1, C3.3-1 for Cell 2 and C.3.2-2, the reported CQI value according to RC.2 TDD / RC.6 TDD in Table A.4-1 in subframes overlapping with aggressor cell ABS and non-ABS subframes shall be in the range of ±1 of the reported median more than 90% of the time. If the PDSCH BLER in non-ABS subframes using the transport format indicated by median CQI obtained by reports in CSI subframe sets C_CSI,1 is less than or equal to 0.1, the BLER in non-ABS subframes using the transport format indicated by the (median CQI + 1) shall be greater than 0.1. If the PDSCH BLER in non-ABS subframes using the transport format indicated by the median CQI is greater than 0.1, the BLER in non-ABS subframes using transport format indicated by (median CQI – 1) shall be less than or equal to 0.1. The value of the median CQI obtained by reports in CSI subframe sets C_CSI,0minus the median CQI obtained by reports in CSI subframe sets C_CSI,1shall be larger than or equal to 2 and less than or equal to 5 in Test 1 and shall be larger than or equal to 0 and less than or equal to 1 in Test 2.

Table 9.2.1.4-1: PUCCH 1-0 static test (TDD)

Parameter			Unit	Test 1				Test 2
				Cell 1			Cell 2	Cell 1		Cell 2
Bandwidth			MHz	10				10
PDSCH transmission mode				2		Note 10		2		Note 10
Uplink downlink configuration				1				1
Special subframe configuration				4				4
Downlink power allocation			dB	-3				-3
			dB	-3				-3
		σ	dB	0				0
Propagation condition and antenna configuration				Clause B.1 (2×2)				Clause B.1 (2×2)
(Note 1)			dB	4	5		6	4	5	-12
at antenna port			dBm/15kHz	-102 (Note 7)			N/A	-98 (Note 7)		N/A
			dBm/15kHz	-98 (Note 8)			N/A	-98 (Note 8)		N/A
			dBm/15kHz	-94.8 (Note 9)			N/A	-98 (Note 9)		N/A
			dB[mW/15kHz]	-94	-93		-92	-94	-93	-110
Subframe Configuration				Non-MBSFN			Non-MBSFN	Non-MBSFN		Non-MBSFN
Cell Id				0			1	0		1
Time Offset between Cells			μs	2.5 (synchronous cells)				2.5 (synchronous cells)
ABS pattern (Note 2)				N/A			0100010001 0100010001	N/A		0100010001 0100010001
RLM/RRM Measurement Subframe Pattern (Note 4)				0000000001 0000000001			N/A	0000000001 0000000001		N/A
CSI Subframe Sets (Note 3)	C_CSI,0			0100010001 0100010001			N/A	0100010001 0100010001		N.A
	C_CSI,1			1000101000 1000101000			N/A	1000101000 1000101000		N/A
Number of control OFDM symbols				3				3
Max number of HARQ transmissions				1				1
Physical channel for C_CSI,0CQI reporting				PUCCH Format 2				PUCCH Format 2
Physical channel for C_CSI,1 CQI reporting				PUSCH (Note 12)				PUSCH
PUCCH Report Type				4				4
Reporting periodicity			ms	N_pd = 5				N_pd = 5
cqi-pmi-ConfigurationIndex C_CSI,0 (Note 13)				3		N/A		3		N/A
cqi-pmi-ConfigurationIndex2 C_CSI,1 (Note 14)				4		N/A		4		N/A
ACK/NACK feedback mode				Multiplexing				Multiplexing
Note 1: For each test, the minimum requirements shall be fulfilled for at least one of the two SNR(s) and the respective wanted signal input level. Note 2: ABS pattern as defined in [9]. Note 3: Time-domain measurement resource restriction pattern for PCell measurements as defined in [7] Note 4: As configured according to the time-domain measurement resource restriction pattern for CSI measurements defined in [7]. Note 5: Time-domain measurement resource restriction pattern for PCell measurements as defined in [7] Note 6: Cell 1 is the serving cell. Cell 2 is the aggressor cell. The number of the CRS ports in Cell1 and Cell2 is the same. Note 7: This noise is applied in OFDM symbols #1, #2, #3, #5, #6, #8, #9, #10,#12, #13 of a subframe overlapping with the aggressor ABS. Note 8: This noise is applied in OFDM symbols #0, #4, #7, #11 of a subframe overlapping with the aggressor ABS Note 9: This noise is applied in all OFDM symbols of a subframe overlapping with aggressor non-ABS. Note 10: Downlink physical channel setup in Cell 2 in accordance with Annex C.3.3 applying OCNG pattern as defined in Annex A.5.2.5 Note 11: Reference measurement channel in Cell 1 RC.2 TDD according to Table A.4-1 for UE Category ≥2 with one sided dynamic OCNG Pattern OP.1 TDD as described in Annex A.5.2.1, and RC.6 TDD according to Table A.4-1 for Category 1 with one/two sided dynami OCNG Pattern OP.1/2 TDD as described in Annex A.5.2.1 and Annex A.5.2.2. Note 12: To avoid collisions between HARQ-ACK and wideband CQI it is necessary to report both on PUSCH instead of PUCCH. PDCCH DCI format 0shall be transmitted in downlink SF#4 and #9 to allow periodic CQI to multiplex with the HARQ-ACK on PUSCH in uplink subframe SF#8 and #3. Note 13: cqi-pmi-ConfigurationIndex is applied for C_CSI,0. Note 14: cqi-pmi-ConfigurationIndex2 is applied for C_CSI,1.

9.2.1.5 FDD (CSI measurements in case two CSI subframe sets are configured and with CRS assistance information)

The following requirements apply to UE Category ≥2. For the parameters specified in Table 9.2.1.5-1, and using the downlink physical channels specified in tables C.3.2-1 for Cell 1, C.3.3-2 for Cell 2 and Cell 3, and C.3.2-2, the reported CQI value according to RC.2 FDD in Table A.4-1 in subframes overlapping with aggressor cell ABS and non-ABS subframes shall be in the range of ±1 of the reported median more than 90% of the time.

For test 1 and test 2, if the PDSCH BLER in ABS subframes using the transport format indicated by median CQI obtained by reports in CSI subframe sets C_CSI,0 is less than or equal to 0.1, the BLER in ABS subframes using the transport format indicated by the (median CQI + 1) shall be greater than 0.1. If the PDSCH BLER in ABS subframes using the transport format indicated by the median CQI is greater than 0.1, the BLER in ABS subframes using transport format indicated by (median CQI – 1) shall be less than or equal to 0.1.

For test 2, if the PDSCH BLER in non-ABS subframes using the transport format indicated by median CQI obtained by reports in CSI subframe sets C_CSI,1 is less than or equal to 0.1, the BLER in non-ABS subframes using the transport format indicated by the (median CQI + 2) shall be greater than 0.1. If the PDSCH BLER in non-ABS subframes using the transport format indicated by the median CQI is greater than 0.1, the BLER in non-ABS subframes using transport format indicated by (median CQI – 1) shall be less than or equal to 0.1.

Table 9.2.1.5-1: PUCCH 1-0 static test (FDD)

Parameter			Unit	Test 1				Test 2
				Cell 1			Cell 2 and 3	Cell 1		Cell 2 and 3
Bandwidth			MHz	10				10
PDSCH transmission mode				2		Note 10		2		Note 10
Downlink power allocation			dB	-3				-3
			dB	-3				-3
		σ	dB	0				0
Propagation condition and antenna configuration				Clause B.1 (2×2)				Clause B.1 (2×2)
(Note 1)			dB	4	5		Cell 2: 12 Cell 3: 10	13	14	Cell 2: 12 Cell 3: 10
at antenna port			dBm/15kHz	-98 (Note 7)			N/A	-98 (Note 7)		N/A
			dBm/15kHz	-98 (Note 8)			N/A	-98 (Note 8)		N/A
			dBm/15kHz	-93 (Note 9)			N/A	-93 (Note 9)		N/A
Subframe Configuration				Non-MBSFN			Non-MBSFN	Non-MBSFN		Non-MBSFN
Cell Id				0			Cell 2: 6 Cell 3: 1	0		Cell 2: 6 Cell 3: 1
Time Offset between Cells			μs	Cell 2: 3 usec Cell 3: -1usec				Cell 2: 3 usec Cell 3: -1usec
Frequency Shift between Cells			Hz	Cell 2: 300Hz Cell 3: -100Hz				Cell 2: 300Hz Cell 3: -100Hz
ABS pattern (Note 2)				N/A			01010101 01010101 01010101 01010101 01010101	N/A		01010101 01010101 01010101 01010101 01010101
RLM/RRM Measurement Subframe Pattern (Note 4)				00000100 00000100 00000100 00000100 00000100			N/A	00000100 00000100 00000100 00000100 00000100		N/A
CSI Subframe Sets (Note 3)	C_CSI,0			01010101 01010101 01010101 01010101 01010101			N/A	01010101 01010101 01010101 01010101 01010101		N/A
	C_CSI,1			10101010 10101010 10101010 10101010 10101010			N/A	10101010 10101010 10101010 10101010 10101010		N/A
Number of control OFDM symbols				3				3
Max number of HARQ transmissions				1				1
Physical channel for C_CSI,0CQI reporting				PUCCH Format 2				PUCCH Format 2
Physical channel for C_CSI,1CQI reporting				PUSCH (Note 12)				PUSCH (Note 12)
PUCCH Report Type				4				4
Reporting periodicity			Ms	N_pd = 5				N_pd = 5
cqi-pmi-ConfigurationIndex C_CSI,0 (Note 13)				6		N/A		6		N/A
cqi-pmi-ConfigurationIndex2 C_CSI,1 (Note 14)				5		N/A		5		N/A
Note 1: For each test, the minimum requirements shall be fulfilled for at least one of the two SNR(s) and the respective wanted signal input level. Note 2: ABS pattern as defined in [9]. Note 3: Time-domain measurement resource restriction pattern for PCell measurements as defined in [7] Note 4: As configured according to the time-domain measurement resource restriction pattern for CSI measurements defined in [7] Note 5: Time-domain measurement resource restriction pattern for PCell measurements as defined in [7] Note 6: Cell 1 is the serving cell. Cell 2 and Cell 3 are the aggressor cells. The number of the CRS ports in Cell1, Cell2, and Cell3 are the same. Note 7: This noise is applied in OFDM symbols #1, #2, #3, #5, #6, #8, #9, #10,#12, #13 of a subframe overlapping with the aggressor ABS. Note 8: This noise is applied in OFDM symbols #0, #4, #7, #11 of a subframe overlapping with the aggressor ABS. Note 9: This noise is applied in all OFDM symbols of a subframe overlapping with aggressor non-ABS. Note 10: Downlink physical channel setup in Cell 2 and Cell 3 in accordance with Annex C.3.3 applying OCNG pattern as defined in Annex A.5.1.5 Note 11: Reference measurement channel in Cell 1 RC.2 FDD according to Table A.4-1 with one sided dynamic OCNG Pattern OP.1 FDD as described in Annex A.5.1.1. Note 12: To avoid collisions between HARQ-ACK and wideband CQI it is necessary to report both on PUSCH instead of PUCCH. PDCCH DCI format 0 shall be transmitted in downlink SF#4 and #9 to allow periodic CQI to multiplex with the HARQ-ACK on PUSCH in uplink subframe SF#8 and #3. Note 13: cqi-pmi-ConfigurationIndex is applied for C_CSI,0. Note 14: cqi-pmi-ConfigurationIndex2 is applied for C_CSI,1.

9.2.1.6 TDD (CSI measurements in case two CSI subframe sets are configured and with CRS assistance information)

The following requirements apply to UE Category ≥2. For the parameters specified in Table 9.2.1.6-1, and using the downlink physical channels specified in tables C.3.2-1 for Cell 1, C3.3-2 for Cell 2 and Cell 3, and C.3.2-2, the reported CQI value according to RC.2 TDD in Table A.4-1 in subframes overlapping with aggressor cell ABS and non-ABS subframes shall be in the range of ±1 of the reported median more than 90% of the time.

Table 9.2.1.6-1: PUCCH 1-0 static test (TDD)

Parameter			Unit	Test 1				Test 2
				Cell 1			Cell 2 and 3	Cell 1		Cell 2 and 3
Bandwidth			MHz	10				10
PDSCH transmission mode				2		Note 10		2		Note 10
Uplink downlink configuration				1				1
Special subframe configuration				4				4
Downlink power allocation			dB	-3				-3
			dB	-3				-3
		σ	dB	0				0
Propagation condition and antenna configuration				Clause B.1 (2×2)				Clause B.1 (2×2)
(Note 1)			dB	4	5		Cell 2: 12 Cell 3: 10	13	14	Cell 2: 12 Cell 3: 10
at antenna port			dBm/15kHz	-98 (Note 7)			N/A	-98 (Note 7)		N/A
			dBm/15kHz	-98 (Note 8)			N/A	-98 (Note 8)		N/A
			dBm/15kHz	-93 (Note 9)			N/A	-93 (Note 9)		N/A
Subframe Configuration				Non-MBSFN			Non-MBSFN	Non-MBSFN		Non-MBSFN
Cell Id				0			Cell 2: 6 Cell 3: 1	0		Cell 2: 6 Cell 3: 1
Time Offset between Cells			μs	Cell 2: 3 usec Cell 3: -1usec				Cell 2: 3 usec Cell 3: -1usec
Frequency shift between Cells			Hz	Cell 2: 300Hz Cell 3: -100Hz				Cell 2: 300Hz Cell 3: -100Hz
ABS pattern (Note 2)				N/A			0100010001 0100010001	N/A		0100010001 0100010001
RLM/RRM Measurement Subframe Pattern (Note 4)				0000000001 0000000001			N/A	0000000001 0000000001		N/A
CSI Subframe Sets (Note 3)	C_CSI,0			0100010001 0100010001			N/A	0100010001 0100010001		N.A
	C_CSI,1			1000101000 1000101000			N/A	1000101000 1000101000		N/A
Number of control OFDM symbols				3				3
Max number of HARQ transmissions				1				1
Physical channel for C_CSI,0CQI reporting				PUCCH Format 2				PUCCH Format 2
Physical channel for C_CSI,1 CQI reporting				PUSCH (Note 12)				PUSCH (Note 12)
PUCCH Report Type				4				4
Reporting periodicity			ms	N_pd = 5				N_pd = 5
cqi-pmi-ConfigurationIndex C_CSI,0 (Note 13)				3		N/A		3		N/A
cqi-pmi-ConfigurationIndex2 C_CSI,1 (Note 14)				4		N/A		4		N/A
ACK/NACK feedback mode				Multiplexing				Multiplexing
Note 1: For each test, the minimum requirements shall be fulfilled for at least one of the two SNR(s) and the respective wanted signal input level. Note 2: ABS pattern as defined in [9]. Note 3: Time-domain measurement resource restriction pattern for PCell measurements as defined in [7] Note 4: As configured according to the time-domain measurement resource restriction pattern for CSI measurements defined in [7]. Note 5: Time-domain measurement resource restriction pattern for PCell measurements as defined in [7] Note 6: Cell 1 is the serving cell. Cell 2 and Cell 3 are the aggressor cells. The number of the CRS ports in Cell1, Cell2, and Cell3 is the same. Note 7: This noise is applied in OFDM symbols #1, #2, #3, #5, #6, #8, #9, #10,#12, #13 of a subframe overlapping with the aggressor ABS. Note 8: This noise is applied in OFDM symbols #0, #4, #7, #11 of a subframe overlapping with the aggressor ABS Note 9: This noise is applied in all OFDM symbols of a subframe overlapping with aggressor non-ABS. Note 10: Downlink physical channel setup in Cell 2 and Cell 3 in accordance with Annex C.3.3 applying OCNG pattern as defined in Annex A.5.2.5 Note 11: Reference measurement channel in Cell 1 RC.2 TDD according to Table A.4-1 with one sided dynamic OCNG Pattern OP.1 TDD as described in Annex A.5.2.1. Note 12: To avoid collisions between HARQ-ACK and wideband CQI it is necessary to report both on PUSCH instead of PUCCH. PDCCH DCI format 0shall be transmitted in downlink SF#4 and #9 to allow periodic CQI to multiplex with the HARQ-ACK on PUSCH in uplink subframe SF#8 and #3. Note 13: cqi-pmi-ConfigurationIndex is applied for C_CSI,0. Note 14: cqi-pmi-ConfigurationIndex2 is applied for C_CSI,1.

9.2.1.7 FDD (Modulation and TBS index Table 2 and 4-bit CQI Table 2 are used)

The following requirements apply to UE Category 11-12 and DL Category ≥11. For the parameters specified in Table 9.2.1.7-1, and using the downlink physical channels specified in tables C.3.2-1 and C.3.2-2, the reported CQI value according to RC.1A FDD in Table A.4-1 shall be in the range of ±1 of the reported median more than 90% of the time. If the PDSCH BLER using the transport format indicated by median CQI is less than or equal to 0.1, the BLER using the transport format indicated by the (median CQI + 1) shall be greater than 0.1, or the BLER using the transport format indicated by the (median CQI + 1) shall be less than or equal to 0.1 when the highest MCS value of the test case has reached. If the PDSCH BLER using the transport format indicated by the median CQI is greater than 0.1, the BLER using transport format indicated by (median CQI – 1) shall be less than or equal to 0.1.

In this test, 4-bit CQI Table 2 in Table 7.2.3-2 in TS 36.213 [6], and Modulation and TBS index table 2 in Table 7.1.7.1-1A for PDSCH in TS 36.213 [6] are applied.

Table 9.2.1.7-1: PUCCH 1-0 static test (FDD)

Parameter		Unit	Test 1		Test 2
Bandwidth		MHz	10
PDSCH transmission mode			1
Downlink power allocation		dB	0
		dB	0
	σ	dB	0
Propagation condition and antenna configuration			AWGN (1 x 2)
SNR (Note 2)		dB	-1	0	20	21
		dB[mW/15kHz]	-99	-98	-78	-77
		dB[mW/15kHz]	-98		-98
Max number of HARQ transmissions			1
Physical channel for CQI reporting			PUCCH Format 2
PUCCH Report Type			4
Reporting periodicity		ms	N_pd = 5
cqi-pmi-ConfigurationIndex			6
Note 1: Reference measurement channel RC.1A FDD according to Table A.4-1 with one sided dynamic OCNG Pattern OP.1 FDD as described in Annex A.5.1.1. Note 2: For each test, the minimum requirements shall be fulfilled for at least one of the two SNR(s) and the respective wanted signal input level.

9.2.1.8 TDD (Modulation and TBS index Table 2 and 4-bit CQI Table 2 are used)

The following requirements apply to UE Category 11-12 and UE DL Category ≥11. For the parameters specified in Table 9.2.1.8-1, and using the downlink physical channels specified in tables C.3.2-1 and C.3.2-2, the reported CQI value according to RC.1A TDD in Table A.4-1 shall be in the range of ±1 of the reported median more than 90% of the time. If the PDSCH BLER using the transport format indicated by median CQI is less than or equal to 0.1, the BLER using the transport format indicated by the (median CQI + 1) shall be greater than 0.1, or the BLER using the transport format indicated by the (median CQI + 1) shall be less than or equal to 0.1 when the highest MCS value of the test case has reached. If the PDSCH BLER using the transport format indicated by the median CQI is greater than 0.1, the BLER using transport format indicated by (median CQI – 1) shall be less than or equal to 0.1.

In this test, 4-bit CQI Table 2 in Table 7.2.3-2 in TS 36.213 [6], and Modulation and TBS index table 2 in Table 7.1.7.1-1A for PDSCH in TS 36.213 [6] are applied.

Table 9.2.1.8-1: PUCCH 1-0 static test (TDD)

Parameter		Unit	Test 1		Test 2
Bandwidth		MHz	20
PDSCH transmission mode			1
Uplink downlink configuration			2
Special subframe configuration			4
Downlink power allocation		dB	0
		dB	0
	σ	dB	0
Propagation condition and antenna configuration			AWGN (1 x 2)
SNR (Note 2)		dB	-1	0	20	21
		dB[mW/15kHz]	-99	-98	-78	-77
		dB[mW/15kHz]	-98		-98
Max number of HARQ transmissions			1
Physical channel for CQI reporting			PUSCH (Note 3)
PUCCH Report Type			4
Reporting periodicity		ms	N_pd = 5
cqi-pmi-ConfigurationIndex			3
ACK/NACK feedback mode			Multiplexing
Note 1: Reference measurement channel RC.1A TDD according to Table A.4-1 with one sided dynamic OCNG Pattern OP.1 TDD as described in Annex A.5.2.1. Note 2: For each test, the minimum requirements shall be fulfilled for at least one of the two SNR(s) and the respective wanted signal input level. Note 3: To avoid collisions between CQI reports and HARQ-ACK it is necessary to report both on PUSCH instead of PUCCH. PDCCH DCI format 0 shall be transmitted in downlink SF#3 and #8 to allow periodic CQI to multiplex with the HARQ-ACK on PUSCH in uplink subframe SF#7 and #2.

9.2.1.9 FDD (Modulation and TBS index Table 3 and 4-bit CQI Table 4 are used)

The following requirements apply to UE DL Category 20 and DL Category ≥22. For the parameters specified in Table 9.2.1.9-1, and using the downlink physical channels specified in tables C.3.2-1 and C.3.2-2, the reported CQI value according to RC.X FDD in Table A.4-1 shall be in the range of ±1 of the reported median more than 90% of the time. If the PDSCH BLER using the transport format indicated by median CQI is less than or equal to 0.1, the BLER using the transport format indicated by the (median CQI + 1) shall be greater than 0.1. If the PDSCH BLER using the transport format indicated by the median CQI is greater than 0.1, the BLER using transport format indicated by (median CQI – 1) shall be less than or equal to 0.1.

In this test, 4-bit CQI Table 4 in Table 7.2.3-4 in TS 36.213 [6], and Modulation and TBS index table 3 in Table 7.1.7.1-1B for PDSCH in TS 36.213 [6] are applied.

Table 9.2.1.9-1: PUCCH 1-0 static test (FDD)

Parameter		Unit	Test 1
Bandwidth		MHz	10
PDSCH transmission mode			1
Downlink power allocation		dB	0
		dB	0
	σ	dB	0
Propagation condition and antenna configuration			AWGN (1 x 2)
SNR (Note 2)		dB	28	29
		dB[mW/15kHz]	-70	-69
		dB[mW/15kHz]	-98
Max number of HARQ transmissions			1
Physical channel for CQI reporting			PUCCH Format 2
PUCCH Report Type			4
Reporting periodicity		ms	N_pd = 5
cqi-pmi-ConfigurationIndex			6
Note 1: Reference measurement channel RC.30 FDD according to Table A.4-1 with one sided dynamic OCNG Pattern OP.1 FDD as described in Annex A.5.1.1. Note 2: For each test, the minimum requirements shall be fulfilled for at least one of the two SNR(s) and the respective wanted signal input level.

9.2.1.10 TDD (Modulation and TBS index Table 3 and 4-bit CQI Table 4 are used)

The following requirements apply to UE DL Category 20 and DL Category ≥22. For the parameters specified in Table 9.2.1.10-1, and using the downlink physical channels specified in tables C.3.2-1 and C.3.2-2, the reported CQI value according to RC.X TDD in Table A.4-1 shall be in the range of ±1 of the reported median more than 90% of the time. If the PDSCH BLER using the transport format indicated by median CQI is less than or equal to 0.1, the BLER using the transport format indicated by the (median CQI + 1) shall be greater than 0.1. If the PDSCH BLER using the transport format indicated by the median CQI is greater than 0.1, the BLER using transport format indicated by (median CQI – 1) shall be less than or equal to 0.1.

In this test, 4-bit CQI Table 3 in Table 7.2.3-4 in TS 36.213 [6], and Modulation and TBS index table 3 in Table 7.1.7.1-1B for PDSCH in TS 36.213 [6] are applied.

Table 9.2.1.10-1: PUCCH 1-0 static test (TDD)

Parameter		Unit	Test 1
Bandwidth		MHz	20
PDSCH transmission mode			1
Uplink downlink configuration			2
Special subframe configuration			4
Downlink power allocation		dB	0
		dB	0
	σ	dB	0
Propagation condition and antenna configuration			AWGN (1 x 2)
SNR (Note 2)		dB	28	29
		dB[mW/15kHz]	-70	-69
		dB[mW/15kHz]	-98
Max number of HARQ transmissions			1
Physical channel for CQI reporting			PUSCH (Note 3)
PUCCH Report Type			4
Reporting periodicity		ms	N_pd = 5
cqi-pmi-ConfigurationIndex			3
ACK/NACK feedback mode			Multiplexing
Note 1: Reference measurement channel RC.30 TDD according to Table A.4-1 with one sided dynamic OCNG Pattern OP.1 TDD as described in Annex A.5.2.1. Note 2: For each test, the minimum requirements shall be fulfilled for at least one of the two SNR(s) and the respective wanted signal input level. Note 3: To avoid collisions between CQI reports and HARQ-ACK it is necessary to report both on PUSCH instead of PUCCH. PDCCH DCI format 0 shall be transmitted in downlink SF#3 and #8 to allow periodic CQI to multiplex with the HARQ-ACK on PUSCH in uplink subframe SF#7 and #2.