8.7.2 TDD (single carrier and CA)
36.1013GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Release 18TSUser Equipment (UE) radio transmission and reception
The parameters specified in Table 8.7.2-1 are valid for all TDD tests unless otherwise stated.
Table 8.7.2-1: Common Test Parameters (TDD)
|
Parameter |
Unit |
Value |
|
Special subframe configuration (Note 1) |
4 |
|
|
Cyclic prefix |
Normal |
|
|
Cell ID |
0 |
|
|
Inter-TTI Distance |
1 |
|
|
Maximum number of HARQ transmission |
4 |
|
|
Redundancy version coding sequence |
{0,0,1,2} for 64QAM and 256QAM |
|
|
Number of OFDM symbols for PDCCH per component carrier |
OFDM symbols |
1 |
|
Cross carrier scheduling |
Not configured |
|
|
Propagation condition |
Static propagation condition No external noise sources are applied |
|
|
Note 1: as specified in Table 4.2-1 in TS 36.211 [4]. |
||
For UE not supporting 256QAM, the requirements are specified in Table 8.7.2-3, with the addition of the parameters in Table 8.7.2-2 and the downlink physical channel setup according to Annex C.3.2. The test points are applied to UE category and bandwidth combination with maximum aggregated bandwidth as specified inTable 8.7.2-4. The TB success rate shall be sustained during at least 300 frames.
For UE supporting 256QAM, the requirements are specified in Table 8.7.2-6, with the addition of the parameters in Table 8.7.2-5 and the downlink physical channel setup according to Annex C.3.2. The test points are applied to UE category and bandwidth combination with maximum aggregated bandwidth as specified inTable 8.7.2-7. The TB success rate shall be sustained during at least 300 frames. For UE supporting 256QAM, the requirement in Table 8.7.2-3 is not applicable.
For UE supporting 256QAM and category 9/10 and category 13, the requirements are specified in both Table 8.7.2-3 and Table 8.7.2-6, with the addition of the parameters in Table 8.7.2-2 and in Table 8.7.2-5 respectivly. The downlink physical channel setup according to Annex C.3.2. The test points are applied to UE category and bandwidth combination with maximum aggregated bandwidth as specified inTable 8.7.2-4 and in Table 8.7.2-7 for the category 9/10 and category 13, the TB success rate shall be sustained during at least 300 frames.
The test coverage for different number of component carriers is defined in 8.1.2.4.
Table 8.7.2-2: test parameters for sustained downlink data rate (TDD 64QAM)
|
Test |
Bandwidth (MHz) |
Transmission mode |
Antenna configuration |
Codebook subset restriction |
Downlink power allocation (dB) |
|
ACK/NACK feedback mode |
Symbols for unused PRBs |
||
|
|
|
σ |
||||||||
|
1 |
10 |
1 |
1 x 2 |
N/A |
0 |
0 |
0 |
-85 |
Bundling |
OP.6 TDD |
|
1A |
10 |
1 |
1×1 |
N/A |
0 |
0 |
0 |
-85 |
Bundling |
OP.6 TDD |
|
1B |
20 |
1 |
1×1 |
N/A |
0 |
0 |
0 |
-85 |
Bundling |
OP.6 TDD |
|
2 |
10 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
Bundling |
OP.1 TDD |
|
3 |
20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
Bundling |
OP.1 TDD |
|
3A |
15 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
Muliplexing |
OP.2 TDD |
|
4,6 |
20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
Multiplexing |
OP.1 TDD |
|
6A |
2×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
– (Note 1) |
OP.1 TDD |
|
6B |
20+15 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 1) |
OP.1 TDD |
|
7 |
3×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 2) |
OP.1 TDD |
|
7A |
15+20+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 2) |
OP.1 TDD |
|
8 |
4×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 2) |
OP.1 TDD |
|
9 |
15+3×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 2) |
OP.1 TDD |
|
10 |
5×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 2) |
OP.1 TDD |
|
11 |
15+4×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 2) |
OP.1 TDD |
|
12 |
6×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 2) |
OP.1 TDD |
|
13 |
7×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 2) |
OP.1 TDD |
|
Note 1: PUCCH format 1b with channel selection is used to feedback ACK/NACK. Note 2: PUCCH format 3 is used to feedback ACK/NACK. |
||||||||||
at antenna port (dBm/15kHz)
Table 8.7.2-3: Minimum requirement (TDD 64QAM)
|
Test |
Number of bits of a DL-SCH transport block received within a TTI for normal/special sub-frame |
Measurement channel |
Reference value |
|
TB success rate [%] |
|||
|
1 |
10296/0 |
R.31-1 TDD |
95 |
|
1A |
10296/0 |
R.31-1 TDD |
95 |
|
1B |
10296/0 |
R.31-1A TDD |
95 |
|
2 |
25456/0 |
R.31-2 TDD |
95 |
|
3 |
51024/0 |
R.31-3 TDD |
95 |
|
3A |
51024/0 |
R.31-3A TDD |
85 |
|
4 |
75376/0 (Note 2) |
R.31-4 TDD |
85 |
|
6 |
75376/0 (Note 2) |
R.31-4 TDD |
85 |
|
6A |
75376/0 (Note 2) |
R.31-4 TDD |
85 |
|
6B |
55056/0 for 15MHz CC 75376/0 for 20MHz CC (Note 2) |
R.31-5 TDD for 15MHz CC R.31-4 TDD for 20MHz CC |
85 |
|
7 |
75376/0 (Note 2) |
R.31-4 TDD |
85 |
|
7A |
55056/0 for 15MHz CC 75376/0 for 20MHz CC (Note 2) |
R.31-5 TDD for 15MHz CC R.31-4 TDD for 20MHz CC |
85 |
|
8 |
75376/0 (Note 2) |
R.31-4 TDD |
85 |
|
9 |
55056/0 for 15MHz CC 75376/0 for 20MHz CC (Note 2) |
R.31-5 TDD for 15MHz CC R.31-4 TDD for 20MHz CC |
85 |
|
10 |
75376/0 (Note 2) |
R.31-4 TDD |
85 |
|
11 |
55056/0 for 15MHz CC 75376/0 for 20MHz CC (Note 2) |
R.31-5 TDD for 15MHz CC R.31-4 TDD for 20MHz CC |
85 |
|
12 |
75376/0 (Note 2) |
R.31-4 TDD |
85 |
|
13 |
75376/0 (Note 2) |
R.31-4 TDD |
85 |
|
Note 1: For 2 layer transmissions, 2 transport blocks are received within a TTI. Note 2: 71112 bits for sub-frame 5. Note 3: The TB success rate is defined as TB success rate = 100%*NDL_correct_rx/ (NDL_newtx + NDL_retx), where NDL_newtx is the number of newly transmitted DL transport blocks, NDL_retx is the number of retransmitted DL transport blocks, and NDL_correct_rx is the number of correctly received DL transport blocks. |
|||
Table 8.7.2-4: Test points for sustained data rate (FRC 64QAM)
|
CA config |
Bandwidth/ Bandwidth combination (MHz) |
Cat. 1 |
Cat. 1bis |
Cat. 2 |
Cat. 3 |
Cat. 4 |
Cat. 6,7 |
Cat. 9, 10 |
Cat. 11, 12 |
DL Cat. 15 |
|
DL Cat. 11, 12 |
||||||||||
|
Single carrier |
10 |
1 |
1A |
2 |
– |
– |
– |
– |
– |
– |
|
15 |
– |
– |
– |
3A |
3A |
– |
– |
– |
– |
|
|
20 |
– |
1B |
– |
3 |
4 |
6 |
– |
– |
– |
|
|
CA with 2CCs |
20+20 |
– |
– |
— |
3(Note 4) |
4 (Note 4) |
6A |
6A |
– |
– |
|
15+20 |
– |
– |
– |
3(Note 4) |
4 (Note 4) |
6B |
6B |
– |
– |
|
|
CA with 3 CCs |
3×20 |
– |
– |
– |
– |
– |
6A |
7 |
7 |
– |
|
15+20+20 |
– |
– |
– |
– |
– |
6A |
7A |
7A |
– |
|
|
CA with 4 CCs |
4×20 |
– |
– |
– |
– |
– |
– |
7 |
8 |
8 |
|
15+3×20 |
– |
– |
– |
– |
– |
– |
7 |
9 |
9 |
|
|
CA with 5 CCs |
5×20 |
10 |
10 |
|||||||
|
15+4×20 |
11 |
11 |
||||||||
|
CA with 6 CCs |
6×20 |
12 |
12 |
|||||||
|
CA with 7 CCs |
7×20 |
13 |
13 |
|||||||
|
Note 1: If DL category is signalled by the UE under test, then select the test point according to UE DL Category. Otherwise, select the test point according to the UE category signalled. Note 2: For non-CA UE, test is selected for maximum supported bandwidth. Note 3: Void. Note 4: If the intra-band contiguous CA is the only CA configuration supported by category 3 or 4 UE, single carrier test is selected. Note 5: The applicability of requirements for different CA configurations and bandwidth combination sets is defined in 8.1.2.3. |
||||||||||
Table 8.7.2-5: test parameters for sustained downlink data rate (TDD 256QAM)
|
Test |
Bandwidth (MHz) |
Transmission mode |
Antenna configuration |
Codebook subset restriction |
Downlink power allocation (dB) |
|
ACK/NACK feedback mode |
Symbols for unused PRBs |
||
|
|
|
σ |
||||||||
|
1 |
20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
Bundling |
OP.1 TDD |
|
2 |
15+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 1) |
OP.1 TDD |
|
3 |
2×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 1) |
OP.1 TDD |
|
4 |
3×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 1) |
OP.1 TDD |
|
5 |
15+20+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 1) |
OP.1 TDD |
|
6 |
4×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 1) |
OP.1 TDD |
|
7 |
15+3×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 1) |
OP.1 TDD |
|
8 |
5×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 1) |
OP.1 TDD |
|
9 |
15+4×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 1) |
OP.1 TDD |
|
10 |
6×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 1) |
OP.1 TDD |
|
11 |
7×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
(Note 1) |
OP.1 TDD |
|
Note 1: For CA test cases, PUCCH format 3 is used to feedback ACK/NACK. |
||||||||||
at antenna port (dBm/15kHz)
Table 8.7.2-6: Minimum requirement (TDD 256QAM)
|
Test |
Measurement channel |
Reference value |
|
TB success rate [%] |
||
|
1 |
R.68 TDD |
85 |
|
2 |
R.68-1 TDD for 15MHz CC R.68 TDD for 20MHz CC |
85 |
|
3 |
R.68 TDD |
85 |
|
4 |
R.68 TDD |
85 |
|
5 |
R.68-1 TDD for 15MHz CC R.68 TDD for 20MHz CC |
85 |
|
6 |
R.68 TDD |
85 |
|
7 |
R.68-1 TDD for 15MHz CC R.68 TDD for 20MHz CC |
85 |
|
8 |
R.68 TDD |
85 |
|
9 |
R.68-1 TDD for 15MHz CC R.68 TDD for 20MHz CC |
85 |
|
10 |
R.68 TDD |
85 |
|
11 |
R.68 TDD |
85 |
|
Note 1: For 2 layer transmissions, 2 transport blocks are received within a TTI. Note 2: The TB success rate is defined as TB success rate = 100%*NDL_correct_rx/ (NDL_newtx + NDL_retx), where NDL_newtx is the number of newly transmitted DL transport blocks, NDL_retx is the number of retransmitted DL transport blocks, and NDL_correct_rx is the number of correctly received DL transport blocks. |
||
Table 8.7.2-7: Test points for sustained data rate (FRC 256QAM)
|
CA config |
Bandwidth/ Bandwidth combination (MHz) |
Cat. 11, 12 |
DL Cat. 13 |
DL Cat. 15 |
DL Cat. 16 |
||
|
DL Cat. 11, 12 |
|||||||
|
Single carrier |
20 |
– |
1 |
– |
– |
||
|
CA with 2CCs |
15+20 |
2 |
2 |
– |
– |
||
|
2×20 |
3 |
3 |
– |
– |
|||
|
CA with 3 CCs |
3×20 |
4 |
3 |
4 |
– |
||
|
15+20+20 |
5 |
3 |
5 |
– |
|||
|
CA with 4 CCs |
4×20 |
4 |
– |
6 |
6 |
||
|
15+3×20 |
5 |
– |
7 |
7 |
|||
|
CA with 5 CCs |
5×20 |
8 |
|||||
|
15+4×20 |
9 |
||||||
|
CA with 6 CCs |
6×20 |
10 |
|||||
|
CA with 7 CCs |
7×20 |
11 |