8.7.1 FDD (single carrier and CA)
36.1013GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Release 18TSUser Equipment (UE) radio transmission and reception
The parameters specified in Table 8.7.1-1 are valid for all FDD tests unless otherwise stated.
Table 8.7.1-1: Common Test Parameters (FDD)
|
Parameter |
Unit |
Value |
|||
|
Cyclic prefix |
Normal |
||||
|
Cell ID |
0 |
||||
|
Inter-TTI Distance |
1 |
||||
|
Number of HARQ processes per component carrier |
Processes |
8 |
|||
|
Maximum number of HARQ transmission |
4 |
||||
|
Redundancy version coding sequence |
{0,0,1,2} for 64QAM and 256QAM |
||||
|
Number of OFDM symbols for PDCCH per component carrier |
OFDM symbols |
1 |
|||
|
Cross carrier scheduling |
Not configured |
||||
|
Propagation condition |
Static propagation condition No external noise sources are applied |
||||
For UE not supporting 256QAM, the requirements are specified in Table 8.7.1-3, with the addition of the parameters in Table 8.7.1-2 and the downlink physical channel setup according to Annex C.3.2. The test points are applied to UE category and bandwidth combination with maximum aggregated bandwidth as specified inTable 8.7.1-4. The TB success rate shall be sustained during at least 300 frames.
For UE supporting 256QAM, the requirements are specified in Table 8.7.1-6, with the addition of the parameters in Table 8.7.1-5 and the downlink physical channel setup according to Annex C.3.2. The test points are applied to UE category and bandwidth combination with maximum aggregated bandwidth as specified in Table 8.7.1-7, the TB success rate shall be sustained during at least 300 frames. For UE supporting 256QAM, the requirement in Table 8.7.1-3 is not applicable.
For UE supporting 256QAM and category 9/10 and category 13, the requirements are specified in both Table 8.7.1-3 and Table 8.7.1-6, with the addition of the parameters in Table 8.7.1-2 and in Table 8.7.1-5 respectivly. The downlink physical channel setup according to Annex C.3.2. The test points are applied to UE category and bandwidth combination with maximum aggregated bandwidth as specified inTable 8.7.1-4 and in Table 8.7.1-7 for the category 9/10 and category 13, the TB success rate shall be sustained during at least 300 frames.
The test coverage for different number of component carriers is defined in 8.1.2.4.
Table 8.7.1-2: test parameters for sustained downlink data rate (FDD 64QAM)
|
Test |
Bandwidth (MHz) |
Transmission mode |
Antenna configuration |
Codebook subset restriction |
Downlink power allocation (dB) |
|
Symbols for unused PRBs |
||
|
|
|
σ |
|||||||
|
1 |
10 |
1 |
1 x 2 |
N/A |
0 |
0 |
0 |
-85 |
OP.6 FDD |
|
1A |
10 |
1 |
1×1 |
N/A |
0 |
0 |
0 |
-85 |
OP.6 FDD |
|
1B |
20 |
1 |
1×1 |
N/A |
0 |
0 |
0 |
-85 |
OP.6 FDD |
|
2 |
10 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
3,4,6 |
20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
3A |
10 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
3B, 4A |
2×10 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
3C, 4B |
15 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
6A |
2×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
6B |
10+15 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
6C |
10+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
6D |
15+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
6E |
2×15 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
6F |
15+5 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
6G |
20+5 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
7 |
3×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
7A |
15+20+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
7B |
10+20+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
7C |
15+15+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
7D |
10+15+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
7E |
10+10+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
7F |
10+15+15 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
7G |
5+10+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
7H |
5+15+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
7I |
5+10+10 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
7J |
5+5+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
7K |
3×10 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
7L |
5+5+10 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
8 |
4×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
8A |
20+20+20+10 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
8B |
20+20+10+10 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
8C |
20+20+10+5 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
8D |
20+10+10+5 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
8E |
15+3×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
8F |
2×15+2×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
8G |
10+15+2×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
8H |
3×10+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
8I |
2×5+2×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
8J |
2×5+10+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
8K |
4×10 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
9 |
5×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
9A |
15+4×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
9B |
10+4×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
9C |
2×10+3×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
9D |
5+10+3×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
9E |
3×10+2×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
9F |
4×10+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
10 |
6×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
11 |
7×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
NOTE 1: For CA test cases, PUCCH format 1b with channel selection is used to feedback ACK/NACK for Test 1-6E, and PUCCH format 3 is used to feedback ACK/NACK for Test 7-7G. |
|||||||||
at antenna port (dBm/15kHz)
Table 8.7.1-3: Minimum requirement (FDD 64QAM)
|
Test |
Number of bits of a DL-SCH transport block received within a TTI |
Measurement channel |
Reference value |
|
TB success rate [%] |
|||
|
1 |
10296 |
R.31-1 FDD |
95 |
|
1A |
10296 |
R.31-1 FDD |
95 |
|
1B |
10296 |
R.31-1A FDD |
95 |
|
2 |
25456 |
R.31-2 FDD |
95 |
|
3 |
51024 |
R.31-3 FDD |
95 |
|
3A |
36696 (Note 2) |
R.31-3A FDD |
85 |
|
3B |
25456 |
R.31-2 FDD |
95 |
|
3C |
51024 |
R.31-3C FDD |
85 |
|
4 |
75376 (Note 3) |
R.31-4 FDD |
85 |
|
4A |
36696 (Note 2) |
R.31-3A FDD |
85 |
|
4B |
55056 (Note 5) |
R.31-4B FDD |
85 |
|
6 |
75376 (Note 3) |
R.31-4 FDD |
85 |
|
6A |
75376 (Note 3) |
R.31-4 FDD |
85 |
|
6B |
36696 (Note 2) for 10MHz CC 55056 for 15MHz CC |
R.31-3A FDD for 10MHz CC R.31-5 FDD for 15MHz CC |
85 |
|
6C |
36696 (Note 2) for 10MHz CC 75376 (Note 3) for 20MHz CC |
R.31-3A FDD for 10MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
6D |
55056 for 15MHz CC 75376 (Note 3) for 20MHz CC |
R.31-5 FDD for 15MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
6E |
55056 (Note 5) for two 15MHz CCs |
R.31-4B FDD for two 15MHz CCs |
85 |
|
6F |
55056 (Note 5) for 15MHz CC 18336 (Note 6) for 5MHz CC |
R.31-5 FDD for 15MHz CC R.31-6 FDD for 5MHz CC |
85 |
|
6G |
75376 (Note 3) for 20MHz CC 18336 (Note 6) for 5MHz CC |
R.31-4 FDD for 20MHz CC R.31-6 FDD for 5MHz CC |
85 |
|
7 |
75376 (Note 3) |
R.31-4 FDD |
85 |
|
7A |
55056 (Note 5) for 15MHz CC 75376 (Note 3) for 20MHz CC |
R.31-5 FDD for 15MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
7B |
36696 (Note 2) for 10MHz CC 75376 (Note 3) for 20MHz CC |
R.31-3A FDD for 10MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
7C |
55056 (Note 5) for 15MHz CC 75376 (Note 3) for 20MHz CC |
R.31-5 FDD for 15MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
7D |
36696 (Note 2) for 10MHz CC 55056 (Note 5) for 15MHz CC 75376 (Note 3) for 20MHz CC |
R.31-3A FDD for 10MHz CC R.31-5 FDD for 15MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
7E |
36696 (Note 2) for 10MHz CC 75376 (Note 3) for 20MHz CC |
R.31-3A FDD for 10MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
7F |
36696 (Note 2) for 10MHz CC 55056 (Note 5) for 15MHz CC |
R.31-3A FDD for 10MHz CC R.31-5 FDD for 15MHz CC |
85 |
|
7G |
18336 (Note 6) for 5MHz CC 36696 (Note 2) for 10MHz CC 75376 (Note 3) for 20MHz CC |
R.31-6 FDD for 5MHz CC R.31-3A FDD for 10MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
7H |
18336 (Note 6) for 5MHz CC 55056 (Note 5) for 15MHz CC 75376 (Note 3) for 20MHz CC |
R.31-6 FDD for 5MHz CC R.31-5 FDD for 15MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
7I |
18336 (Note 6) for 5MHz CC 36696 (Note 2) for 10MHz CC |
R.31-6 FDD for 5MHz CC R.31-3A FDD for 10MHz CC |
85 |
|
7J |
18336 (Note 6) for 5MHz CC 75376 (Note 3) for 20MHz CC |
R.31-6 FDD for 5MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
7K |
36696 (Note 2) for 10MHz CC |
R.31-3A FDD for 10MHz CC |
85 |
|
7L |
18336 (Note 6) for 5MHz CC 36696 (Note 2) for 10MHz CC |
R.31-6 FDD for 5MHz CC R.31-3A FDD for 10MHz CC |
85 |
|
8E |
55056 (Note 5) for 15MHz CC 75376 (Note 3) for 20MHz CC |
R.31-5 FDD for 15MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
8F |
55056 (Note 5) for 15MHz CC 75376 (Note 3) for 20MHz CC |
R.31-5 FDD for 15MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
8G |
36696 (Note 2) for 10MHz CC 55056 (Note 5) for 15MHz CC 75376 (Note 3) for 20MHz CC |
R.31-3A FDD for 10MHz CC R.31-5 FDD for 15MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
8H |
36696 (Note 2) for 10MHz CC 75376 (Note 3) for 20MHz CC |
R.31-3A FDD for 10MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
8I |
18336 (Note 6) for 5MHz CC 75376 (Note 3) for 20MHz CC |
R.31-6 FDD for 5MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
8J |
18336 (Note 6) for 5MHz CC 36696 (Note 2) for 10MHz CC 75376 (Note 3) for 20MHz CC |
R.31-6 FDD for 5MHz CC R.31-3A FDD for 10MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
8K |
36696 (Note 2) for 10MHz CC |
R.31-3A FDD for 10MHz CC |
85 |
|
8 |
75376 (Note 3) |
R.31-4 FDD |
85 |
|
8A |
36696 (Note 2) for 10MHz CC 75376 (Note 3) for 20MHz CC |
R.31-3A FDD for 10MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
8B |
36696 (Note 2) for 10MHz CC 75376 (Note 3) for 20MHz CC |
R.31-3A FDD for 10MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
8C |
18336 (Note 6) for 5MHz CC 36696 (Note 2) for 10MHz CC 75376 (Note 3) for 20MHz CC |
R.31-6 FDD for 5MHz CC R.31-3A FDD for 10MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
8D |
18336 (Note 6) for 5MHz CC 36696 (Note 2) for 10MHz CC 75376 (Note 3) for 20MHz CC |
R.31-6 FDD for 5MHz CC R.31-3A FDD for 10MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
9 |
75376 (Note 3) |
R.31-4 FDD |
85 |
|
9A |
55056 (Note 5) for 15MHz CC 75376 (Note 3) for 20MHz CC |
R.31-5 FDD for 15MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
9B |
36696 (Note 2) for 10MHz CC 75376 (Note 3) for 20MHz CC |
R.31-3A FDD for 10MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
9C |
36696 (Note 2) for 10MHz CC 75376 (Note 3) for 20MHz CC |
R.31-3A FDD for 10MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
9D |
18336 (Note 6) for 5MHz CC 36696 (Note 2) for 10MHz CC 75376 (Note 3) for 20MHz CC |
R.31-6 FDD for 5MHz CC R.31-3A FDD for 10MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
9E |
36696 (Note 2) for 10MHz CC 75376 (Note 3) for 20MHz CC |
R.31-3A FDD for 10MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
9F |
36696 (Note 2) for 10MHz CC 75376 (Note 3) for 20MHz CC |
R.31-3A FDD for 10MHz CC R.31-4 FDD for 20MHz CC |
85 |
|
10 |
75376 (Note 3) |
R.31-4 FDD |
85 |
|
11 |
75376 (Note 3) |
R.31-4 FDD |
85 |
|
Note 1: For 2 layer transmissions, 2 transport blocks are received within a TTI. Note 2: 35160 bits for sub-frame 5. Note 3: 71112 bits for sub-frame 5. Note 4: The TB success rate is defined as TB success rate = 100%*NDL_correct_rx/ (NDL_newtx + NDL_retx), where NDL_newtx is the number of newly transmitted DL transport blocks, NDL_retx is the number of retransmitted DL transport blocks, and NDL_correct_rx is the number of correctly received DL transport blocks. Note 5: 52752bits for sub-frame 5. Note 6: 15840bits for sub-frame 0. |
|||
Table 8.7.1-4: Test points for sustained data rate (FRC 64QAM)
|
CA config |
Maximum supported Bandwidth/ Bandwidth combination (MHz) |
Cat. 1 |
Cat. 1bis |
Cat. 2 |
Cat. 3 |
Cat. 4 |
Cat. 6,7 |
Cat. 9,10 |
Cat 11, 12 |
DL Cat. 15 |
|
DL Cat. 11,12 |
||||||||||
|
Single carrier |
10 |
1 |
1A |
2 |
3A |
3A |
– |
– |
– |
– |
|
15 |
– |
– |
– |
3C |
4B |
– |
– |
– |
– |
|
|
20 |
– |
1B |
– |
3 |
4 |
6 |
– |
– |
– |
|
|
CA with 2CCs |
10+10 |
– |
– |
– |
3B |
4A |
4A |
4A |
– |
– |
|
10+15 |
– |
– |
– |
3B |
4A |
6B |
6B |
– |
– |
|
|
10+20 |
– |
– |
– |
3B |
4A |
6C |
6C |
– |
– |
|
|
15+15 |
– |
– |
– |
3B |
4A |
6E |
6E |
– |
– |
|
|
15+5 |
– |
3B |
4A |
6F |
6F |
– |
– |
|||
|
20+5 |
– |
– |
– |
3 |
4 |
6G |
6G |
– |
– |
|
|
15+20 |
– |
– |
– |
3B |
4A |
6D |
6D |
– |
– |
|
|
20+20 |
– |
– |
– |
3B or 3 (Note 4) |
4A or 4 (Note 4) |
6A |
6A |
– |
– |
|
|
CA with 3CCs |
3×20 |
– |
– |
– |
– |
– |
6A |
7 |
7 |
– |
|
15+20+20 |
– |
– |
– |
– |
– |
6A |
7A |
7A |
– |
|
|
10+20+20 |
– |
– |
– |
– |
– |
6A |
7B |
7B |
– |
|
|
15+15+20 |
– |
6D |
7C |
7C |
– |
|||||
|
10+15+20 |
– |
– |
– |
– |
– |
6D |
7D |
7D |
– |
|
|
10+10+20 |
– |
– |
– |
– |
– |
7E |
7E |
7E |
– |
|
|
10+15+15 |
– |
– |
– |
– |
– |
7F |
7F |
7F |
– |
|
|
5+10+20 |
– |
– |
– |
– |
– |
7G |
7G |
7G |
– |
|
|
5+15+20 |
– |
– |
– |
– |
– |
7H |
7H |
7H |
– |
|
|
5+10+10 |
– |
– |
– |
– |
– |
7I |
7I |
7I |
– |
|
|
5+5+20 |
7J |
7J |
7J |
|||||||
|
3×10 |
7K |
7K |
7K |
|||||||
|
5+5+10 |
7L |
7L |
7L |
|||||||
|
CA with 4CCs |
4×20 |
– |
– |
– |
– |
– |
– |
7 |
8 |
8 |
|
20+20+20+10 |
– |
– |
– |
– |
– |
– |
7 |
8A |
8A |
|
|
20+20+10+10 |
– |
– |
– |
– |
– |
– |
8B |
8B |
8B |
|
|
20+20+10+5 |
– |
– |
– |
– |
– |
– |
8C |
8C |
8C |
|
|
20+10+10+5 |
– |
– |
– |
– |
– |
– |
8D |
8D |
8D |
|
|
15+3×20 |
8E |
8E |
8E |
|||||||
|
2×15+2×20 |
8F |
8F |
8F |
|||||||
|
10+15+2×20 |
8G |
8G |
8G |
|||||||
|
3×10+20 |
8H |
8H |
8H |
|||||||
|
2×5+2×20 |
8I |
8I |
8I |
|||||||
|
2×5+10+20 |
8J |
8J |
8J |
|||||||
|
4×10 |
8K |
8K |
8K |
|||||||
|
CA with 5CCs |
5×20 |
– |
– |
– |
– |
– |
– |
– |
8 |
9 |
|
15+4×20 |
10 |
|||||||||
|
10+4×20 |
11 |
|||||||||
|
2×10+3×20 |
12 |
|||||||||
|
5+10+3×20 |
13 |
|||||||||
|
3×10+2×20 |
14 |
|||||||||
|
CA with 6CCs |
6×20 |
– |
– |
– |
– |
– |
– |
– |
10 |
10 |
|
CA with 7CCs |
7×20 |
– |
– |
– |
– |
– |
– |
– |
11 |
11 |
|
Note 1: Void. Note 2: For non-CA UE, test is selected for maximum supported bandwidth. Note 3: Void. Note 4: If the intra-band contiguous CA is the only CA configuration supported by category 3 or 4 UE, the single carrier test is selecte, i.e., Test 3 for UE category 3 and Test 4 for UE category 4. Otherwise, Test 3B applies for category 3 UE and Test 4A applies for category 4 UE. Note 5: The applicability of requirements for different CA configurations and bandwidth combination sets is defined in 8.1.2.3. Note 6: If DL category is signalled by the UE under test, then select the test point according to UE DL Category. Otherwise, select the test point according to the UE category signalled. |
||||||||||
Table 8.7.1-5: test parameters for sustained downlink data rate (FDD 256QAM)
|
Test |
Bandwidth (MHz) |
Transmission mode |
Antenna configuration |
Codebook subset restriction |
Downlink power allocation (dB) |
|
Symbols for unused PRBs |
||
|
|
|
σ |
|||||||
|
1 |
20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
2 |
2×15 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
2A |
15+5 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
3 |
10+15 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
3A |
20+5 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
4 |
10+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
6 |
15+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
7 |
2×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
8 |
3×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
9 |
15+20+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
10 |
10+20+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
11 |
15+15+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
12 |
10+15+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
13 |
10+10+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
14 |
10+15+15 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
15 |
5+10+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
15A |
5+15+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
15B |
5+10+10 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
15C |
5+5+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
15D |
3×10 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
15E |
5+5+10 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
16 |
4×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
17 |
20+20+20+10 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
18 |
20+20+10+10 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
18A |
20+20+10+5 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
18B |
20+10+10+5 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
18C |
15+3×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
18D |
2×15+2×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
18E |
10+15+2×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
18F |
3×10+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
18G |
2×5+2×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
18H |
2×5+10+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
18I |
4×10 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
19 |
5×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
19A |
15+4×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
19B |
10+4×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
19C |
2×10+3×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
19D |
5+10+3×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
19E |
3×10+2×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
19F |
4×10+20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
20 |
6×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
21 |
7×20 |
3 |
2 x 2 |
10 |
-3 |
-3 |
0 |
-85 |
OP.1 FDD |
|
Note 1: For CA test cases, PUCCH format 3 is used to feedback ACK/NACK. |
|||||||||
at antenna port (dBm/15kHz)
Table 8.7.1-6: Minimum requirement (FDD 256QAM)
|
Test |
Measurement channel |
Reference value |
|
TB success rate [%] |
||
|
1 |
R.68 FDD |
85 |
|
2 |
R.68-1 FDD |
85 |
|
2A |
R.68-1 FDD for 15MHz CC R.68-3 FDD for 5MHz CC |
85 |
|
3 |
R.68-2 FDD for 10MHz CC R.68-1 FDD for 15MHz CC |
85 |
|
3A |
R.68 FDD for 20MHz CC R.68-3 FDD for 5MHz CC |
85 |
|
4 |
R.68-2 FDD for 10MHz CC R.68 FDD for 20MHz CC |
85 |
|
6 |
R.68-1 FDD for 15MHz CC R.68 FDD for 20MHz CC |
85 |
|
7 |
R.68 FDD |
85 |
|
8 |
R.68 FDD |
85 |
|
9 |
R.68-1 FDD for 15MHz CC R.68 FDD for 20MHz CC |
85 |
|
10 |
R.68-2 FDD for 10MHz CC R.68 FDD for 20MHz CC |
85 |
|
11 |
R.68-1 FDD for 15MHz CC R.68 FDD for 20MHz CC |
85 |
|
12 |
R.68-2 FDD for 10MHz CC R.68-1 FDD for 15MHz CC R.68 FDD for 20MHz CC |
85 |
|
13 |
R.68-2 FDD for 10MHz CC R.68 FDD for 20MHz CC |
85 |
|
14 |
R.68-2 FDD for 10MHz CC R.68-1 FDD for 15MHz CC |
85 |
|
15 |
R.68-3 FDD for 5MHz CC R.68-2 FDD for 10MHz CC R.68 FDD for 20MHz CC |
85 |
|
15A |
R.68-3 FDD for 5MHz CC R.68-1 FDD for 15MHz CC R.68 FDD for 20MHz CC |
85 |
|
15B |
R.68-3 FDD for 5MHz CC R.68-2 FDD for 10MHz CC |
85 |
|
15C |
R.68-3 FDD for 5MHz CC R.68 FDD for 20MHz CC |
85 |
|
15D |
R.68-2 FDD for 10MHz CC |
85 |
|
15E |
R.68-3 FDD for 5MHz CC R.68-2 FDD for 10MHz CC |
85 |
|
16 |
R.68 FDD |
85 |
|
17 |
R.68-2 FDD for 10MHz CC R.68 FDD for 20MHz CC |
85 |
|
18 |
R.68-2 FDD for 10MHz CC R.68 FDD for 20MHz CC |
85 |
|
18A |
R.68-3 FDD for 5MHz CC R.68-2 FDD for 10MHz CC R.68 FDD for 20MHz CC |
85 |
|
18B |
R.68-3 FDD for 5MHz CC R.68-2 FDD for 10MHz CC R.68 FDD for 20MHz CC |
85 |
|
18C |
R.68-1 FDD for 15MHz CC R.68 FDD for 20MHz CC |
85 |
|
18D |
R.68-1 FDD for 15MHz CC R.68 FDD for 20MHz CC |
85 |
|
18E |
R.68-2 FDD for 10MHz CC R.68-1 FDD for 15MHz CC R.68 FDD for 20MHz CC |
85 |
|
18F |
R.68-2 FDD for 10MHz CC R.68 FDD for 20MHz CC |
85 |
|
18G |
R.68-3 FDD for 5MHz CC R.68 FDD for 20MHz CC |
85 |
|
18H |
R.68-3 FDD for 5MHz CC R.68-2 FDD for 10MHz CC R.68 FDD for 20MHz CC |
85 |
|
18I |
R.68-2 FDD for 10MHz CC |
85 |
|
19 |
R.68 FDD |
85 |
|
19A |
R.68-1 FDD for 15MHz CC R.68 FDD for 20MHz CC |
85 |
|
19B |
R.68-2 FDD for 10MHz CC R.68 FDD for 20MHz CC |
85 |
|
19C |
R.68-2 FDD for 10MHz CC R.68 FDD for 20MHz CC |
85 |
|
19D |
R.68-3 FDD for 5MHz CC R.68-2 FDD for 10MHz CC R.68 FDD for 20MHz CC |
85 |
|
19E |
R.68-2 FDD for 10MHz CC R.68 FDD for 20MHz CC |
85 |
|
19F |
R.68-2 FDD for 10MHz CC R.68 FDD for 20MHz CC |
85 |
|
20 |
R.68 FDD |
85 |
|
21 |
R.68 FDD |
85 |
|
Note 1: For 2 layer transmissions, 2 transport blocks are received within a TTI. Note 2: The TB success rate is defined as TB success rate = 100%*NDL_correct_rx/ (NDL_newtx + NDL_retx), where NDL_newtx is the number of newly transmitted DL transport blocks, NDL_retx is the number of retransmitted DL transport blocks, and NDL_correct_rx is the number of correctly received DL transport blocks. |
||
Table 8.7.1-7: Test points for sustained data rate (FRC 256QAM)
|
CA config |
Maximum supported Bandwidth/ Bandwidth combination (MHz) |
Cat. 11, 12 |
DL Cat. 13 |
DL Cat. 15 |
DL Cat. 16 |
||
|
DL Cat. 11, 12 |
|||||||
|
Single carrier |
20 |
– |
1 |
– |
– |
||
|
CA with 2CCs |
2×15 |
2 |
2 |
– |
– |
||
|
15+5 |
2A |
2A |
– |
– |
|||
|
10+15 |
3 |
3 |
– |
– |
|||
|
20+5 |
3A |
3A |
– |
– |
|||
|
10+20 |
4 |
4 |
– |
– |
|||
|
15+20 |
6 |
6 |
– |
– |
|||
|
20+20 |
7 |
7 |
– |
– |
|||
|
CA with 3CCs |
3×20 |
8 |
7 |
8 |
– |
||
|
15+20+20 |
9 |
7 |
9 |
– |
|||
|
10+20+20 |
10 |
7 |
10 |
– |
|||
|
15+15+20 |
11 |
6 |
11 |
– |
|||
|
10+15+20 |
12 |
6 |
12 |
– |
|||
|
10+10+20 |
13 |
13 |
13 |
– |
|||
|
10+15+15 |
14 |
14 |
14 |
– |
|||
|
5+10+20 |
15 |
15 |
15 |
– |
|||
|
5+15+20 |
15A |
15A |
15A |
– |
|||
|
5+10+10 |
15B |
15B |
15B |
– |
|||
|
5+5+20 |
15C |
15C |
15C |
||||
|
3×10 |
15D |
15D |
15D |
||||
|
5+5+10 |
15E |
15E |
15E |
||||
|
CA with 4CCs |
4×20 |
8 |
– |
16 |
16 |
||
|
20+20+20+10 |
8 |
– |
17 |
17 |
|||
|
20+20+10+10 |
18 |
– |
18 |
18 |
|||
|
20+20+10+5 |
18A |
– |
18A |
18A |
|||
|
20+10+10+5 |
18B |
– |
18B |
18B |
|||
|
15+3×20 |
18C |
18C |
18C |
||||
|
2×15+2×20 |
18D |
18D |
18D |
||||
|
10+15+2×20 |
18E |
18E |
18E |
||||
|
3×10+20 |
18F |
18F |
18F |
||||
|
2×5+2×20 |
18G |
18G |
18G |
||||
|
2×5+10+20 |
18H |
18H |
18H |
||||
|
4×10 |
18I |
18I |
18I |
||||
|
CA with 5CCs |
5×20 |
– |
– |
16 |
19 |
||
|
15+4×20 |
20 |
||||||
|
10+4×20 |
21 |
||||||
|
2×10+3×20 |
22 |
||||||
|
5+10+3×20 |
23 |
||||||
|
3×10+2×20 |
24 |
||||||
|
4×10+20 |
25 |
||||||
|
CA with 6CCs |
6×20 |
– |
– |
– |
20 |
||
|
CA with 7CCs |
7×20 |
– |
– |
– |
21 |
||
|
NOTE 1: If DL category is signalled by the UE under test, then select the test point according to UE DL Category. Otherwise, select the test point according to the UE category signalled. |
|||||||