11 Performance requirement (ProSe Direct Discovery)
36.1013GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Release 18TSUser Equipment (UE) radio transmission and reception
This clause contains the performance requirements for the Sidelink physical channels specified for ProSe Direct Discovery.
11.1 General
11.1.1 Applicability of requirements
The requirements in this clause are applicable to UEs that support ProSe Direct Discovery. The test case applicability is in according to table 11.1.1-1 depending on set of supported UE capabilities.
Table 11.1.1-1: ProSe Direct Discovery test applicability
|
FDD/TDD |
Tests / clause |
Applicable if UE indicates at least the following capability |
|
FDD |
11.2.1 |
ProSe Direct Discovery without support of disc-SLSS-r12 |
|
11.2.3 |
ProSe Direct Discovery with support of discPeriodicSLSS-r13 and ProSe Direct Communication |
|
|
11.3.1 |
ProSe Direct Discovery |
|
|
11.4.1 |
ProSe Direct Discovery with support of disc-SLSS-r12 |
|
|
11.5.1 |
ProSe Direct Discovery |
|
|
TDD |
11.2.2 |
ProSe Direct Discovery |
|
11.3.2 |
ProSe Direct Discovery |
|
|
11.5.2 |
ProSe Direct Discovery |
For maximum Sidelink Processes test specified in clause 11.5, the UE is required to only meet the test for the maximum channel bandwidth over the ProSe operating bands supported by the UE. Test case 11.2.3 for 5MHz channel bandwidth is applicable to UEs that support ProSe Direct Communication on Band 31 only.
11.1.2 Reference DRX configuration
Table 11.1.2-1: Reference DRX configuration
|
Parameter |
Value |
Comments |
|
onDurationTimer |
psf1 |
|
|
drx-InactivityTimer |
psf1 |
|
|
drx-RetransmissionTimer |
psf1 |
|
|
longDRX-CycleStartOffset |
sf2560, 0 |
|
|
shortDRX |
disabled |
|
|
NOTE 1: For further information see clause 6.3.2 in TS 36.331. |
||
11.2 Demodulation of PSDCH (single link performance)
The purpose of the requirements in this subclause is to verify the PSDCH demodulation performance with a single active PSDCH link under different operating scenarios and channel conditions.
The active cell(s), when present, are specified in the test parameters specific to the test.
11.2.1 FDD (in-coverage)
The minimum requirements are specified in Table 11.2.1-2 with the test parameters specified in Table 11.2.1-1. The receiver UE under test is associated with Cell 1.
Table 11.2.1-1: Test Parameters
|
Parameter |
Unit |
Test 1 |
||
|
Discovery resource pool configuration |
As specified in Table A.7.1.1-1 (Configuration #1-FDD) |
|||
|
DRX configuration |
As specified in Table 11.1.2-1 |
|||
|
at antenna port (NOTE 3)
|
dBm/15kHz |
-98 |
||
|
Active cell(s) |
Cell 1 (Serving cell) |
|||
|
Cell 1 |
Cyclic prefix |
Normal |
||
|
Cell ID |
0 |
|||
|
Downlink power allocation |
 |
dB |
0 |
|
 |
dB |
0 (NOTE 1) |
||
|
σ |
dB |
0 |
||
|
OCNG Pattern (NOTE 2) |
OP.1 FDD |
|||
|
Propagation channel |
AWGN |
|||
|
Antenna configuration |
1×2 |
|||
|
RSRP |
dBm/15kHz |
-92 |
||
|
Active Sidelink UE(s) |
Sidelink UE 1 |
|||
|
Sidelink UE 1 |
Sidelink Transmissions |
PSDCH |
||
|
PSDCH RB allocation |
PRB pairs {2i..2i+1}, where i is chosen randomly uniformly from [0,11] in each discovery period. |
|||
|
Time offset (NOTE 4) |
μs |
+1 |
||
|
Frequency offset (NOTE 5) |
Hz |
+200 |
||
|
Propagation Channel |
EPA5 |
|||
|
Antenna configuration |
1×2 Low |
|||
|
NOTE 1: .
NOTE 2: OCNG is used to fully allocate the available resource blocks to virtual UEs. NOTE 3: Applicable to both DL channel and ProSe Direct Discovery Subframes on UL. NOTE 4: Time offset of Sidelink UE receive signal with respect to Cell 1 downlink timing at the tested UE. NOTE 5: Frequency offset of Sidelink UE with respect to Cell 1 uplink frequency. |
||||
Table 11.2.1-2: Minimum performance
|
Test num. |
Sidelink UE |
Band-width |
Reference channel |
Reference value |
|
|
BLER of PSDCH (%) |
SNR (dB) |
||||
|
1 |
1 |
5 MHz |
D.1 FDD |
30 |
4.6 |
11.2.2 TDD (in-coverage)
The minimum requirements are specified in Table 11.2.2-2 with the test parameters specified in Table 11.2.2-1. The receiver UE under test is associated with Cell 1.
Table 11.2.2-1: Test Parameters
|
Parameter |
Unit |
Test 1 |
||
|
Discovery resource pool configuration |
As specified in Table A.7.1.2-1 (Configuration #1-TDD) |
|||
|
DRX configuration |
As specified in Table 11.1.2-1 |
|||
|
at antenna port (NOTE 5)
|
dBm/15kHz |
-98 |
||
|
Active cell(s) |
Cell 1 (Serving cell) |
|||
|
Cell 1 |
Cyclic prefix |
Normal |
||
|
Uplink downlink configuration (NOTE 3) |
0 |
|||
|
Special subframe configuration (NOTE 4) |
4 |
|||
|
Cell ID |
0 |
|||
|
Downlink power allocation |
 |
dB |
0 |
|
 |
dB |
0 (NOTE 1) |
||
|
σ |
dB |
0 |
||
|
OCNG Pattern NOTE 2 |
OP.1 TDD |
|||
|
Propagation channel |
AWGN |
|||
|
Antenna configuration |
1×2 |
|||
|
RSRP |
dBm/15kHz |
-92 |
||
|
Active Sidelink UE(s) |
Sidelink UE 1 |
|||
|
Sidelink UE 1 |
Sidelink Transmissions |
PSDCH |
||
|
RB allocation |
PRB pairs {2i..2i+1}, where i is chosen randomly uniformly from [0,11] in each discovery period. |
|||
|
Time offset (NOTE 6) |
μs |
+1 |
||
|
Frequency offset (NOTE 7) |
Hz |
+200 |
||
|
Propagation Channel |
EPA5 |
|||
|
Antenna configuration |
1×2 Low |
|||
|
NOTE 1: .
NOTE 2: OCNG is used to fully allocate the available resource blocks to virtual UEs. NOTE 3: As specified in Table 4.2-2 in TS 36.211 [4]. NOTE 4: As specified in Table 4.2-1 in TS 36.211 [4]. NOTE 5: Applicable to both DL subframes and UL subframes configured for ProSe Direct Discovery. NOTE 6: Time offset of Sidelink UE receive signal with respect to Cell 1 downlink timing at the tested UE. NOTE 7: Frequency offset of Sidelink UE with respect to Cell 1 uplink frequency. |
||||
Table 11.2.2-2: Minimum performance
|
Test num. |
Sidelink UE |
Band-width |
Reference channel |
Reference value |
|
|
BLER of PSDCH (%) |
SNR (dB) |
||||
|
1 |
1 |
5 MHz |
D.1 TDD |
30 |
4.6 |
11.2.3 FDD (out-of-coverage)
The minimum requirements are specified in Table 11.2.3-2 with the test parameters specified in Table 11.2.3-1. The receiver UE under test is out of network coverage.
Table 11.2.3-1: Test Parameters
|
Parameter |
Unit |
Test 1 |
|
|
Resource pool configuration |
As specified in Table A.7.1.1-4 (Configuration #4-FDD) |
||
|
DRX configuration |
As specified in Table 11.1.2-1 |
||
|
at antenna port
|
dBm/15kHz |
-98 |
|
|
Active cell(s) |
None |
||
|
Active Sidelink UE(s) |
Sidelink UEs 1, 2 |
||
|
Sidelink UE 1 |
Sidelink Transmissions |
SLSS + PSBCH |
|
|
networkControlledSyncTx |
ON |
||
|
slssid |
30 |
||
|
inCoverage (in MIB-SL) |
TRUE |
||
|
syncOffsetIndicator |
Set same as syncOffsetIndicator1 in Configuration #4-FDD |
||
|
Propagation channel |
EPA5 |
||
|
Antenna configuration |
1×2 Low |
||
|
at antenna port
|
dBm/15kHz |
-82 |
|
|
Sidelink UE 2 |
Sidelink Transmissions |
PSDCH |
|
|
PSDCH RB allocation |
PRB pairs {2i..2i+1}, where i is chosen randomly uniformly from [0,11] (for 5MHz) or [0,24] (for 10MHz) in each discovery period. |
||
|
Time offset (Note 1) |
μs |
+1 |
|
|
Frequency offset (Note 2) |
Hz |
+200 |
|
|
Propagation Channel |
EPA5 |
||
|
Antenna configuration |
1×2 Low |
||
|
NOTE 1: Time offset of Sidelink UE 2 receive signal timing with respect to Sidelink UE 1 receive signal timing at the tested UE. NOTE 2: Frequency offset of Sidelink UE 2 with respect to Sidelink UE 1 transmit frequency. |
|||
Table 11.2.3-2: Minimum performance
|
Test number |
Sidelink UE |
Band-width |
Reference channel |
Reference value |
|
|
BLER of PSDCH (%) |
SNR (dB) |
||||
|
1 |
1 |
5 MHz |
D.1 FDD |
30 |
4.6 |
|
10 MHz |
|||||
11.3 Power imbalance performance with two links
The purpose of this test is to check the demodulation performance when receiving PSDCH transmissions from two Sidelink UEs with power imbalance in one subframe.
11.3.1 FDD
The minimum requirements are specified in Table 11.3.1-2 with the test parameters specified in Table 11.3.1-1. The receiver UE under test is associated with Cell 1. The Sidelink UE 1 and 2 are synchronized to Cell 1 and transmit PSDCH on adjacent RBs.
Table 11.3.1-1: Test Parameters
|
Parameter |
Unit |
Test 1 |
||
|
Discovery resource pool configuration |
As specified in Table A.7.1.1-1 (Configuration #1-FDD) |
|||
|
DRX configuration |
As specified in Table 11.1.2-1 |
|||
|
at antenna port (NOTE 3)
|
dBm/15kHz |
-98 |
||
|
Active cell(s) |
Cell 1 (Serving cell) |
|||
|
Cell 1 |
Cyclic prefix |
Normal |
||
|
Cell ID |
0 |
|||
|
Downlink power allocation |
 |
dB |
0 |
|
 |
dB |
0 (NOTE 1) |
||
|
σ |
dB |
0 |
||
|
OCNG Pattern (NOTE 2) |
OP.1 FDD |
|||
|
Propagation channel |
AWGN |
|||
|
Antenna configuration |
1×2 |
|||
|
RSRP |
dBm/15kHz |
-92 |
||
|
Active Sidelink UE(s) |
Sidelink UE 1, Sidelink UE 2 |
|||
|
Sidelink UE 1 |
Sidelink Transmissions |
PSDCH |
||
|
PSDCH RB allocation |
PRB pairs {4..5} |
|||
|
Time offset (NOTE 3) |
μs |
0 |
||
|
Frequency offset (NOTE 4) |
Hz |
0 |
||
|
Propagation Channel |
AWGN |
|||
|
Antenna configuration |
1×2 Low |
|||
|
Sidelink UE 2 |
Sidelink Transmissions |
PSDCH |
||
|
PSDCH RB allocation |
PRB pairs {6..7} |
|||
|
Time offset (w.r.t. Cell 1 DL) |
μs |
0 |
||
|
Frequency offset (w.r.t. Cell 1 UL) |
Hz |
0 |
||
|
Propagation Channel |
AWGN |
|||
|
Antenna configuration |
1×2 Low |
|||
|
NOTE 1: .
NOTE 2: OCNG is used to fully allocate the available resource blocks to virtual UEs. NOTE 3: Applicable to both DL channel and ProSe Direct Discovery Subframes on UL. NOTE 4: Time offset of Sidelink UE receive signal with respect to Cell 1 downlink timing at the tested UE. NOTE 5: Frequency offset of Sidelink UE with respect to Cell 1 uplink frequency. |
||||
Table 11.3.1-2: Minimum performance
|
Test num. |
Band-width |
Sidelink UE |
Reference channel |
Reference value |
|
|
BLER of PSDCH (%) |
SNR (dB) |
||||
|
1 |
5 MHz |
1 |
D.1 FDD |
(NOTE 1) |
24.3 |
|
2 |
D.1 FDD |
30 |
6.9 |
||
|
NOTE 1: There is no BLER requirement for Sidelink UE 1. |
|||||
11.3.2 TDD
The minimum requirements are specified in Table 11.3.2-2 with the test parameters specified in Table 11.3.2-1. The receiver UE under test is associated with Cell 1. The Sidelink UE 1 and 2 are synchronized to Cell 1 and transmit PSDCH on adjacent RBs.
Table 11.3.2-1: Test Parameters
|
Parameter |
Unit |
Test 1 |
||
|
Discovery resource pool configuration |
As specified in Table A.7.1.2-1 (Configuration #1-TDD) |
|||
|
DRX configuration |
As specified in Table 11.1.2-1 |
|||
|
at antenna port (NOTE 5)
|
dBm/15kHz |
-98 |
||
|
Active cell(s) |
Cell 1 (Serving cell) |
|||
|
Cell 1 |
Cyclic prefix |
Normal |
||
|
Uplink downlink configuration (NOTE 3) |
0 |
|||
|
Special subframe configuration (NOTE 4) |
4 |
|||
|
Cell ID |
0 |
|||
|
Downlink power allocation |
 |
dB |
0 |
|
 |
dB |
0 (NOTE 1) |
||
|
σ |
dB |
0 |
||
|
OCNG Pattern NOTE 2 |
OP.1 TDD |
|||
|
Propagation channel |
AWGN |
|||
|
Antenna configuration |
1×2 |
|||
|
RSRP |
dBm/15kHz |
-92 |
||
|
Active Sidelink UE(s) |
Sidelink UE 1, Sidelink UE 2 |
|||
|
Sidelink UE 1 |
Sidelink Transmissions |
PSDCH |
||
|
PSDCH RB allocation |
PRB pairs {4..5} |
|||
|
Time offset (NOTE 6) |
μs |
0 |
||
|
Frequency offset (NOTE 7) |
Hz |
0 |
||
|
Propagation Channel |
AWGN |
|||
|
Antenna configuration |
1×2 Low |
|||
|
Sidelink UE 2 |
Sidelink Transmissions |
PSDCH |
||
|
RB allocation |
PRB pairs {6..7} |
|||
|
Time offset (NOTE 6) |
μs |
0 |
||
|
Frequency offset (NOTE 7) |
Hz |
0 |
||
|
Propagation Channel |
AWGN |
|||
|
Antenna configuration |
1×2 Low |
|||
|
NOTE 1: .
NOTE 2: OCNG is used to fully allocate the available resource blocks to virtual UEs. NOTE 3: As specified in Table 4.2-2 in TS 36.211 [4]. NOTE 4: As specified in Table 4.2-1 in TS 36.211 [4]. NOTE 5: Applicable to both DL subframes and UL subframes configured for ProSe Direct Discovery. NOTE 6: Time offset of Sidelink UE receive signal with respect to Cell 1 downlink timing at the tested UE. NOTE 7: Frequency offset of Sidelink UE with respect to Cell 1 uplink frequency. |
||||
Table 11.3.2-2: Minimum performance
|
Test num. |
Band-width |
Sidelink UE |
Reference channel |
Reference value |
|
|
BLER of PSDCH (%) |
SNR (dB) |
||||
|
1 |
5 MHz |
1 |
D.1 TDD |
(NOTE 1) |
24.3 |
|
2 |
D.1 TDD |
30 |
6.9 |
||
|
NOTE 1: There is no BLER requirement for Sidelink UE 1. |
|||||
11.4 Multiple timing reference test
The purpose of this test is to check the demodulation performance when receiving from two Sidelink UEs that follow different timing references and transmitting on different resources (non-overlapping in time).
11.4.1 FDD
The test parameters are specified in Table 11.4.1-1. Sidelink UE 2 and the receiver UE under test are associated with Cell 1. Sidelink UE 1 and 3 are associated with another cell and use a different timing, and UE 1 acts as a synchronization reference. The minimum requirements are specified in Table 11.4.1-2.
Table 11.4.1-1: Test Parameters
|
Parameter |
Unit |
Test 1 |
||
|
Discovery resource pool configuration |
As specified in Table A.7.1.1-2 (Configuration #2-FDD) |
|||
|
DRX configuration |
As specified in Table 11.1.2-1 |
|||
|
at antenna port (NOTE 3)
|
dBm/15kHz |
-98 |
||
|
Active cell(s) |
Cell 1 (Serving cell) |
|||
|
Cell 1 |
Cyclic prefix |
Normal |
||
|
Cell ID |
0 |
|||
|
Downlink power allocation |
 |
dB |
0 |
|
 |
dB |
0 (NOTE 1) |
||
|
σ |
dB |
0 |
||
|
OCNG Pattern NOTE 2 |
OP.1 FDD |
|||
|
Propagation channel |
AWGN |
|||
|
Antenna configuration |
1×2 |
|||
|
RSRP |
dBm/15kHz |
-92 |
||
|
Active Sidelink UE(s) |
Sidelink UEs 1, 2, 3 |
|||
|
Sidelink UE 1 |
Sidelink Transmissions |
SLSS |
||
|
networkControlledSyncTx |
ON |
|||
|
slssid |
30 |
|||
|
Time offset (NOTE 4) |
μs |
3511 |
||
|
Frequency offset (NOTE 5) |
Hz |
-100 |
||
|
Propagation channel |
EPA5 |
|||
|
Antenna configuration |
1×2 Low |
|||
|
of SLSS at antenna port
|
dBm/15kHz |
-82 |
||
|
Sidelink UE 2 |
Sidelink Transmissions |
PSDCH |
||
|
Resource pool used for transmissions |
discRxPool(0) |
|||
|
RB allocation |
PRB pairs {2i..2i+1}, where i is chosen randomly uniformly from [0,11] in each discovery period. |
|||
|
Time offset (NOTE 4) |
μs |
+1 |
||
|
Frequency offset (NOTE 5) |
Hz |
+200 |
||
|
Propagation Channel |
EPA5 |
|||
|
Antenna configuration |
1×2 Low |
|||
|
Sidelink UE 3 |
Sidelink Transmissions |
PSDCH |
||
|
Resource pool used for transmissions |
discRxPool(1) |
|||
|
RB allocation |
PRB pairs {2i..2i+1}, where i is chosen randomly uniformly from [0,11] in each discovery period. |
|||
|
Time offset (NOTE 4) |
μs |
3511 |
||
|
Frequency offset (NOTE 5) |
Hz |
+300 |
||
|
Propagation Channel |
EPA5 |
|||
|
Antenna configuration |
1×2 Low |
|||
|
NOTE 1: .
NOTE 2: OCNG is used to fully allocate the available resource blocks to virtual UEs. NOTE 3: Applicable to both DL channel and ProSe Direct Discovery Subframes on UL. NOTE 4: Time offset of Sidelink UE receive signal with respect to Cell 1 downlink timing at the tested UE. NOTE 5: Frequency offset of Sidelink UE with respect to Cell 1 uplink frequency. |
||||
Table 11.4.1-2: Minimum performance
|
Test num. |
Band-width |
Sidelink UE |
Reference channel |
Reference value |
|
|
BLER of PSDCH (%)NOTE 1 |
SNR (dB) |
||||
|
1 |
5 MHz |
2 |
D.1 FDD |
30 |
4.6 |
|
3 |
D.1 FDD |
30 |
4.6 |
||
|
NOTE 1: The BLER is measured after 5 D2D Discovery periods (1600 frames) of lead time during which the test UE detects and synchronizes to Sidelink UE 1 SLSS. |
|||||
11.5 Maximum Sidelink processes test
The purpose of this test is to verify the maximum number of Sidelink processes supported by the UE as reported using UE capability signalling (discSupportedProc).
The UE is required to meet only the test for the maximum channel bandwidth over the ProSe operating bands supported by the UE.
11.5.1 FDD
The test parameters are specified in Table 11.5.1-1. Multiple discovery resource pools are interleaved. Each Sidelink UE transmits in one of the resource pools with 3 retransmissions. The minimum requirements are specified in Table 11.5.1-2.
Table 11.5.1-1: Test Parameters
|
Parameter |
Unit |
Test 1-7 |
||
|
Discovery resource pool configuration |
As specified in Table A.7.1.1-3 (Configuration #3-FDD) with parameters BWChannel, NPools = Number of configured resource pools (as specified in Table 11.5.1-2), and N = discSupportedProc |
|||
|
DRX configuration |
As specified in Table 11.1.2-1 |
|||
|
Active cell(s) |
Cell 1 (Serving cell) |
|||
|
Cell 1 |
Cyclic prefix |
Normal |
||
|
Cell ID |
0 |
|||
|
Downlink power allocation |
 |
dB |
0 |
|
 |
dB |
0 (NOTE 1) |
||
|
σ |
dB |
0 |
||
|
OCNG Pattern NOTE 2 |
OP.1 FDD |
|||
|
Propagation channel |
Static propagation condition No external noise sources are applied |
|||
|
Antenna configuration |
1×2 |
|||
|
RSRP |
dBm/15kHz |
-85 |
||
|
Active Sidelink UE(s) |
Sidelink UE i, i = 0, …, discSupportedProc-1 |
|||
|
Sidelink UE i |
Sidelink Transmissions |
PSDCH (D.1 FDD) |
||
|
Resource pool index (NOTE 3) |
 |
|||
|
PSDCH RB allocation (NOTE 3) |
PRB pairs {2*(i % NMAX_SF), 2*(i % NMAX_SF)+1} |
|||
|
Time offset (NOTE 4) |
μs |
0 |
||
|
Frequency offset (NOTE 4) |
Hz |
0 |
||
|
Propagation Channel |
Static propagation condition No external noise sources are applied |
|||
|
Antenna configuration |
1×2 Low |
|||
|
NOTE 1: .
NOTE 2: OCNG is used to fully allocate the available resource blocks to virtual UEs.. NOTE 3: NMAX_SF represents the maximum number of Sidelink UEs transmitting in one subframe. NMAX_SF = 12 (5 MHz), 25 (10MHz), 37 (15MHz), 50 (10MHz). NOTE 4: Time offset of Sidelink UE receive signal with respect to Cell 1 downlink timing at the tested UE. NOTE 5: Frequency offset of Sidelink UE with respect to Cell 1 uplink frequency. |
||||
Table 11.5.1-2: Minimum performance
|
Test num. |
Bandwidth |
discSupportedProc |
Number of configured resource pools |
|
Reference value |
|
Fraction of maximum throughput (%) |
|||||
|
1 |
5 MHz |
50 |
5 |
-85 |
95 |
|
2 |
10 MHz |
50 |
2 |
-85 |
95 |
|
3 |
15 MHz |
50 |
2 |
-85 |
95 |
|
4 |
20 MHz |
50 |
1 |
-85 |
95 |
|
5 |
10 MHz |
400 |
16 |
-85 |
95 |
|
6 |
15 MHz |
400 |
11 |
-85 |
95 |
|
7 |
20 MHz |
400 |
8 |
-85 |
95 |
at antenna port (dBm/15kHz)11.5.2 TDD
The test parameters are specified in Table 11.5.2-1. Multiple discovery resource pools are interleaved. Each Sidelink UE transmits in one of the resource pools with 3 retransmissions. The minimum requirements are specified in Table 11.5.2-2.
Table 11.5.2-1: Test Parameters
|
Parameter |
Unit |
Test 1-7 |
||
|
Discovery resource pool configuration |
As specified in Table A.7.1.2-2 (Configuration #2-TDD) with parameters BWChannel, NPools = Number of configured resource pools (as specified in Table 11.5.2-2), and N = discSupportedProc |
|||
|
DRX configuration |
As specified in Table 11.1.2-1 |
|||
|
Active cell(s) |
Cell 1 (Serving cell) |
|||
|
Cell 1 |
Cyclic prefix |
Normal |
||
|
Uplink downlink configuration (NOTE 3) |
0 |
|||
|
Special subframe configuration (NOTE 4) |
4 |
|||
|
Cell ID |
0 |
|||
|
Downlink power allocation |
 |
dB |
0 |
|
 |
dB |
0 (NOTE 1) |
||
|
σ |
dB |
0 |
||
|
OCNG Pattern NOTE 2 |
OP.1 TDD |
|||
|
Propagation channel |
Static propagation condition No external noise sources are applied |
|||
|
Antenna configuration |
1×2 |
|||
|
RSRP |
dBm/15kHz |
-85 |
||
|
Active Sidelink UE(s) |
Sidelink UE i, i = 0, …, discSupportedProc-1 |
|||
|
Sidelink UE i |
Sidelink Transmissions |
PSDCH (D.1 TDD) |
||
|
PSDCH Resource pool (NOTE 5) |
 |
|||
|
PSDCH RB allocation (NOTE 5) |
PRB pairs {2*(i % NMAX_SF),2*(i % NMAX_SF)+1} |
|||
|
Time offset (NOTE 6) |
μs |
0 |
||
|
Frequency offset (NOTE 7) |
Hz |
0 |
||
|
Propagation Channel |
Static propagation condition No external noise sources are applied |
|||
|
Antenna configuration |
1×2 Low |
|||
|
NOTE 1: .
NOTE 2: OCNG is used to fully allocate the available resource blocks to virtual UEs. NOTE 3: As specified in Table 4.2-2 in TS 36.211 [4]. NOTE 4: As specified in Table 4.2-1 in TS 36.211 [4]. NOTE 5: NMAX_SF represents the maximum number of Sidelink UEs transmitting in one subframe. NMAX_SF = 12 (5 MHz), 25 (10MHz), 37 (15MHz), 50 (10MHz). NOTE 6: Time offset of Sidelink UE receive signal with respect to Cell 1 downlink timing at the tested UE. NOTE 7: Frequency offset of Sidelink UE with respect to Cell 1 uplink frequency. |
||||
Table 11.5.2-2: Minimum performance
|
Test num. |
Bandwidth |
discSupportedProc |
Number of configured resource pools |
|
Reference value |
|
Fraction of maximum throughput (%) for Sidelink UE i=0…discSupportedProc-1 |
|||||
|
1 |
5 MHz |
50 |
5 |
-85 |
95 |
|
2 |
10 MHz |
50 |
2 |
-85 |
95 |
|
3 |
15 MHz |
50 |
2 |
-85 |
95 |
|
4 |
20 MHz |
50 |
1 |
-85 |
95 |
|
5 |
10 MHz |
400 |
16 |
-85 |
95 |
|
6 |
15 MHz |
400 |
11 |
-85 |
95 |
|
7 |
20 MHz |
400 |
8 |
-85 |
95 |
at antenna port (dBm/15kHz