Cell Barred

MP

Enumerated(not barred, barred)

If the cell is operating in MBSFN mode as indicated in subclause 8.1.1.6.3 and the value in this IE is different from “barred” the UE behaviour is unspecified.

Intra-frequency cell re-selection indicator

CV-Barred

Enumerated(not allowed, allowed)

T_barred

CV-Barred

Integer (10,20,40,80,160,320,640,1280)

[4]

[s]

Cell Reserved for operator use

MP

Enumerated(reserved, not reserved)

Cell Reservation Extension

MP

Enumerated(reserved, not reserved)

Cell Reserved for CSG

CV-CSG

Enumerated(TRUE)

REL-8

Access Class Barred list

CV-SIB3-MD

maxAC

Default is no access class barred is applied.

The first instance of the parameter corresponds to Access Class 0, the second to Access Class 1 and so on up to Access Class 15. UE reads this IE of its access class stored in SIM.

>Access Class Barred

MP

Enumerated (barred, not barred)

Barred

The IE is mandatory present if the IE "Cell Barred" has the value "Barred"; otherwise the element is not needed in the message.

SIB3-MD

The IE is mandatory and has a default value if the IE "Cell Access Restriction" is included in SIB 3. Otherwise the IE is not needed.

CSG

The IE is optional present if the cell is a CSG cell and the IE “Cell Reservation Extension” has the value "reserved". Otherwise the IE is not needed. The IE is not included in System Information Block type 4.

Cell identity

MP

bit string(28)

Mapping Info

OP

Mapping info 10.3.2.5

For FDD, 3.84 Mcps TDD and 7.68 Mcps TDD, this IE should not be sent.

Cell selection and reselection quality measure

MP

Enumerated (CPICH Ec/N0, CPICH RSCP)

Choice of measurement (CPICH Ec/N0 or CPICH RSCP) to use as quality measure Q for FDD cells.

This IE is also sent to the UE in SIB11/12. Both occurrences of the IE should be set to the same value.

CHOICE mode

MP

>FDD

>>S_intrasearch

OP

Integer (-32..20 by step of 2)

If a negative value is received the UE shall consider the value to be 0.

[4]

[dB]

>>S_intersearch

OP

Integer (-32..20 by step of 2)

If a negative value is received the UE shall consider the value to be 0.

[4]

[dB]

>>S_searchHCS

OP

Integer (-105..91 by step of 2)

If a negative value is received the UE shall consider the value to be 0.

[4]

[dB]

>>RAT List

OP

1 to <maxOtherRAT>

>>>RAT identifier

MP

Enumerated (GSM, cdma2000)

>>>S_search,RAT

MP

Integer (-32..20 by step of 2)

In case the value 20 is received the UE shall consider this IE as if it was absent according to [4]

If a negative value is received the UE shall consider the value to be 0.

[dB]

>>>S_HCS,RAT

OP

Integer (-105..91 by step of 2)

If a negative value is received the UE shall consider the value to be 0.

[4]

[dB]

>>>S_{limit,SearchRAT}

MP

Integer (-32..20 by step of 2)

If a negative value is received the UE shall consider the value to be 0.

[4]

[dB]

>>Qqualmin

MP

Integer (-24..0)

Ec/N0, [dB]

>>Qrxlevmin

MP

Integer (-115..-25 by step of 2)

RSCP, [dBm]

>> Delta_Qrxlevmin

CV-Delta

Integer(-4..-2 by step of 2)

If present, the actual value of Qrxlevmin = Qrxlevmin + Delta_Qrxlevmin

REL-5

>>Qqualmin-offset

CV-SIB3

Integer (1..16)

Ec/N0, [dB]

The default value is 0

REL-7

>>Qrxlevmin-offset

CV-SIB3

Integer (2..16 by step of 2)

RSCP, [dB]

The default value is 0

REL-7

>>Tx Fail Params

CV-SIB3op

REL-12

>>>ConnEst Fail Count

MP

Enumerated (1, 2, 3, 4)

Number of times that the UE detects RRC Connection Establishment failure on the same cell before applying ConnEst Fail Qoffset_,temp.

[4]

REL-12

>>>Offset Validity

MP

Enumerated (30, 60, 120, 240, 300, 420, 600, 900)

Length of time UE uses the ConnEst Fail Qoffset_,temp before the offset is removed from the cell.

[4]

[s]

REL-12

>>>ConnEst Fail Qoffset_,temp

OP

Integer (0..15)

Temporary cell selection/reselection offset used for this cell if RRC Connection Establishment fails. Absence of the IE means that the UE shall apply the value of infinity.

[4]

[dB]

REL-12

>TDD

>>S_intrasearch

OP

Integer (-105..91 by step of 2)

If a negative value is received the UE shall consider the value to be 0.

[4]

[dB]

>>S_intersearch

OP

Integer (-105..91 by step of 2)

If a negative value is received the UE shall consider the value to be 0.

[4]

[dB]

>>S_searchHCS

OP

Integer (-105..91 by step of 2)

If a negative value is received the UE shall consider the value to be 0.

[4]

[dB]

>>RAT List

OP

1 to <maxOtherRAT>

>>>RAT identifier

MP

Enumerated (GSM, cdma2000)

>>>S_search,RAT

MP

Integer (-105..91 by step of 2)

In case the value 91 is received the UE shall consider this IE as if it was absent according to [4]

If a negative value is received the UE shall consider the value to be 0.

[dB]

>>>S_HCS,RAT

OP

Integer (-105..91 by step of 2)

If a negative value is received the UE shall consider the value to be 0.

[4]

[dB]

>>>S_{limit,SearchRAT}

MP

Integer (-105..91 by step of 2)

If a negative value is received the UE shall consider the value to be 0.

[4]

[dB]

>>Qrxlevmin

MP

Integer (-115..-25 by step of 2)

RSCP, [dBm]

>>Delta_Qrxlevmin

CV-Delta

Integer(-4..-2 by step of 2)

If present, the actual value of Qrxlevmin = Qrxlevmin + Delta_Qrxlevmin

REL-5

>>Qrxlevmin-offset

CV-SIB3

Integer (2..16 by step of 2)

RSCP, [dB]

The default value is 0

REL-7

Qhyst1_s

MP

Integer (0..40 by step of 2)

[4]

[dB]

Qhyst1_s,PCH

CV-SIB4

Integer (0..40)

If present, it is used as Qhyst1_s for UE in CELL_PCH or URA_PCH state [4]
[dB]

REL-5

Qhyst1_s,FACH

CV-SIB4

Integer (0..40)

If present, it is used as Qhyst1_s for UE in CELL_FACH state [4]
[dB]

REL-5

Qhyst2_s

CV-FDD-Quality-Measure

Integer (0..40 by step of 2)

Default value is Qhyst1_s

[4]

[dB]

Qhyst2_s,PCH

CV-SIB4-FDD-Quality-Measure

Integer (0..40)

If present, it is used as Qhyst2_s for UE using CPICH Ec/No quality measure in CELL_PCH or URA_PCH state. Default value is Qhyst1_s,PCH
[4]
[dB]

REL-5

Qhyst2_s,FACH

CV-SIB4-FDD-Quality-Measure

Integer (0..40)

If present, it is used as Qhyst2_s for UE using CPICH Ec/No quality measure in CELL_FACH state. Default value is Qhyst1_s,FACH
[4]
[dB]

REL-5

Treselections

MP

Integer (0..31)

[s]

Treselection_s,PCH

CV-SIB4

Integer (0..31)

If present, it is used as Treselections for UE in CELL_PCH or URA_PCH state [4]
[s]

REL-5

Treselection_s,FACH

CV-SIB4

Real (0..6.2 by step of 0.2)

If present, it is used as Treselection_s for UE in CELL_FACH state [4]
[s]

REL-5

Speed dependent ScalingFactor for Treselection

OP

Real (0..1 by step of 0.1)

This IE is used by the UE in high mobility state as scaling factor for Treselection_s or Treselection_s,PCH or Treselection_s,FACH [4]. If present and HCS is used, the UE behaviour is unspecified.

REL-5

Inter-frequency ScalingFactor for Treselection

OP

Real (1..4.75 by step of 0.25)

If present, it is used by the UE as scaling factor for Treselection_s or Treselection_s,PCH or Treselection_s,FACH for inter-frequency cell reselection evaluation [4]. If present and HCS is used, the UE behaviour is unspecified.

REL-5

Inter-RAT ScalingFactor for Treselection

OP

Real (1..4.75 by step of 0.25)

If present, it is used by the UE as scaling factor for Treselection_s or Treselection_s,PCH or Treselection_s,FACH for inter-RAT cell reselection evaluation [4]. If present and HCS is used, the UE behaviour is unspecified.

REL-5

Non-HCS_T_CRmax

MD

Enumerated (not used, 30, 60, 120, 180, 240)

[s]

Default value is ‘not used’.

REL-5

Non-HCS_N_CR

CV-UE speed detector_MD

Integer (1..16)

Default value = 8

REL-5

Non-HCS_T_CRmaxHyst

CV-UE speed detector_MP

Enumerated (not used, 10, 20, 30, 40, 50, 60, 70)

[s]

REL-5

HCS Serving cell Information

OP

HCS Serving cell information 10.3.7.12

Maximum allowed UL TX power

MP

Maximum allowed UL TX power 10.3.6.39

[dBm] UE_TXPWR_MAX_RACH in [4].

FDD-Quality-Measure

The IE is not needed if the IE "Cell selection and reselection quality measure" has the value CPICH RSCP, otherwise the IE is mandatory and has a default value.

Delta

This IE is optional if the value of Qrxlevmin is below –115dBm. It is not needed otherwise.

SIB3

This IE is mandatory default if the IE “Cell selection and re-selection info for SIB3/4” is included in SIB type 3. It is not needed otherwise.

SIB3op

This IE is optional if the IE "Cell selection and re-selection info for SIB3/4" is included in SIB type 3. It is not needed otherwise.

SIB4

This IE is optional if the IE “Cell selection and re-selection info for SIB3/4” is included in SIB type 4. It is not needed otherwise.

SIB4-FDD-Quality-Measure

This IE is optional if the IE “Cell selection and re-selection info for SIB3/4” is included in SIB type 4, and the IE "Cell selection and reselection quality measure" has the value CPICH Ec/N0. It is not needed otherwise.

UE Speed detector_MD (non-HCS)

This IE is not needed if non-HCS_T_CRmax equals ‘not used’, else it is mandatory default.

UE Speed detector_MP (non-HCS)

This IE is not needed if non-HCS_T_CRmax equals ‘not used’, else it is mandatory present.

Qoffset1_s,n

MD

Integer(-50..50)

Default value is 0.

[dB]

Qoffset2_s,n

CV-FDD-Quality-Measure

Integer(-50..50)

Default value is 0.

[dB]

Maximum allowed UL TX power

MD

Maximum allowed UL TX power 10.3.6.39

According to UE_TXPWR_MAX_RACH in [4], [dBm].

If applied to FDD or TDD cells, the default is the Maximum allowed UL TX power for the serving cell.

If applied to a GSM cell, the default is the UE maximum output power applicable for this GSM cell, according to the UE’s radio access capability.

HCS neighbouring cell information

OP

HCS Neighbouring cell information 10.3.7.11

CHOICE mode

MP

>FDD

>>Qqualmin

CV-FDD-Serving-Cell

Integer (-24..0)

Ec/N0, [dB]

Default value is Qqualmin for the serving cell

>>Qrxlevmin

MD

Integer (-115..-25 by step of 2)

RSCP, [dBm]

Default value is Qrxlevmin for the serving cell

>>Delta_Qrxlevmin

CV-Delta

Integer(-4..-2 by step of 2)

If present, the actual value of Qrxlevmin = Qrxlevmin + Delta_Qrxlevmin

REL-5

>TDD

>>Qrxlevmin

MD

Integer (-115..-25 by step of 2)

RSCP, [dBm]

Default value is Qrxlevmin for the serving cell

>> Delta_Qrxlevmin

CV-Delta

Integer(-4..-2 by step of 2)

If present, the actual value of Qrxlevmin = Qrxlevmin + Delta_Qrxlevmin

REL-5

>GSM

>>Qrxlevmin

MD

Integer (-115..-25 by step of 2)

GSM RSSI, [dBm]

Default value is Qrxlevmin for the serving cell

FDD-Quality-Measure

This IE is mandatory and has a default value for Intra/Inter Frequency Cells if the IE "Cell selection and reselection quality measure" has the value CPICH Ec/No. Otherwise the IE is absent.

FDD-Serving-Cell

This IE is mandatory and has a default value if the serving cell is an FDD cell. Otherwise the IE is mandatory present.

Delta

This IE is optional if Qrxlevmin is present and the value of Qrxlevmin is below –115dBm. It is not needed otherwise.

Mapping List

MP

1 to <MaxRAT>

>RAT

MP

Enumerated (UTRA FDD, UTRA TDD 3.84 Mcps, UTRA TDD 1.28 Mcps, GSM, cdma2000)

UTRA TDD 1.28 Mcps is included for REL-4.

>Mapping Function Parameter List

MP

1 to <maxMeasIntervals>

>>Function type

MP

Enumerated (linear, function type 2, function type 3, function type 4)

Type of the function within the interval.

For 1.28Mcps TDD only. If IE “RAT” is set to “UTRA TDD 3.84 Mcps”, the IE should be interpreted as:

Enumerated (frequency scope1, frequency scope2, frequency scope3, RSCP threshold).

REL-11

>>Map_parameter_1

MD

Integer (0..99)

Parameter describing the mapping function between the quality measurement and the representing quality value, see [4].

Default value is zero for the first interval or otherwise the value of Map_parameter_2 of the interval before.

For 1.28Mcps TDD only.

See Note1/Note2

REL-11

Integer (0..127)

For 1.28 Mcps TDD, the parameter is used to indicate the uplink access location of the serving cell.

REL-7

>>Map_parameter_2

MP

Integer (0..99)

Parameter describing the mapping function between the quality measurement and the representing quality value, see [4].

For 1.28Mcps TDD only.

See Note1

REL-11

>>Upper_limit

CV-MaxInt

Integer (1..MaxMeas)

Upper limit of interval for which the Map_parameter_1 and Map_parameter_2 are valid.

MaxMeas = 25 if RAT = UTRA FDD / CPICH Ec/N0,
MaxMeas = 91 if RAT = UTRA TDD 3.84 Mcps or if RAT = UTRA TDD 1.28 Mcps or if RAT = UTRA FDD/ CPICH RSCP,
MaxMeas = 63 if RAT = GSM.

UTRA TDD 1.28 Mcps is included for REL-4.

For 1.28Mcps TDD only.

See Note1

REL-11

MaxInt

This IE is mandatory present if Mapping Function Parameter List has not reached maxMeasIntervals and is not needed otherwise.

URA identity

MP

bit string(16)

CHOICE Action

MP

REL-8

>Clear dedicated priorities

NULL

REL-8

>Configure dedicated priorities

REL-8

>>T322

OP

Integer (5, 10, 20, 30, 60, 120, 180)

Time in minutes for which the configured dedicated priorities are valid. When the timer expires the UE should revert to using the priorities signalled in system information. Absence of this IE means that the configured dedicated priorities are valid until the next update.

One spare value needed.

REL-8

>>Priority Level List

OP

1 to <maxPrio>

REL-8

1 to <maxPrio-ext>

REL-13

>>>priority

OP

Integer (0.. <maxPrio–1>)

If this IE is absent then the UE behaviour is unspecified. 0 is the lowest priority and maxPrio-1 is the highest.

REL-8

>>>subpriority

CV-E-UTRA-priority

Enumerated(oDot2, oDot4, oDot6, oDot8)

Fractional priority value. If present, this value is added to the value of IE "priority".

REL-13

>>>CHOICE Radio Access Technology

MP

REL-8

>>>>UTRA FDD

REL-8

>>>>>Frequency List

MP

1 to < maxNumFDDFreqs>

REL-8

>>>>>>UARFCN

MP

Integer(0 .. 16383)

UARFCN of the downlink carrier frequency [25.101]

REL-8

>>>>UTRA TDD

REL-8

>>>>>Frequency List

MP

1 to < maxNumTDDFreqs>

REL-8

>>>>>>UARFCN

MP

Integer(0 .. 16383)

UARFCN of the downlink carrier frequency [25.101]

REL-8

>>>>E-UTRA

REL-8

>>>>>Frequency List

1 to <maxNumEUTRAFreqs>

REL-8

>>>>>>EARFCN

MP

Integer(0 .. 65535)

EARFCN of the downlink carrier frequency [64]. If the IE indicates a value of 65535, then the EARFCN for this instance should be read from the corresponding instance of IE "EARFCN extension".

REL-8

>>>>>>EARFCN extension

OP

Integer(65536 …262143)

EARFCN of the downlink carrier frequency [64].

REL-11

>>>>GSM

REL-8

>>>>>GSM cell group

MP

GSM cell group 10.3.7.9a

REL-8

>>E-UTRA detection

MP

Boolean

‘TRUE’ means that the UE may detect the presence of a E-UTRA cell and report to NAS

REL-8

E-UTRA-priority

This IE is optionally present if IE "Radio Access Technology" is set to E-UTRA and if IE "priority" is present. Otherwise it is not needed.

CSG Identity

MP

Bit string(27)

As defined in [76]

REL-8

Start PSC

MP

Integer (0..504 by step of 8)

The value of this IE specifies the start PSC of the first PSC range (NOTE 1).

REL-8

Number of PSCs

MP

Enumerated (5, 10, 15, 20, 30, 40, 50, 64, 80, 120, 160, 256, alltheRest)

This IE specifies the number of PSCs reserved for CSG cells in each PSC range. “alltheRest” indicates all values from Start PSC to 511.

Three spare values are needed.

REL-8

PSC Range 2 Offset

CV-alltheRest

Integer (8..504 by step of 8)

If this IE is included, the UE shall calculate the second PSC range (NOTE 2).

If this IE is not included, the UE shall consider the second PSC range to be not present.

REL-8

NOTE 1: Let the IE "Start PSC" = s. and "Number of PSCs" = n. The complete set of (n) PSC values in range 1 is defined as: {s, ((s + 1) mod 512), ((s + 2) mod 512) … ((s + n-1) mod 512)}.

NOTE 2: Let the IEs "Start PSC" + "Number of PSCs" – 1 + "PSC Range 2 Offset" = s. and "Number of PSCs" = n. The complete set of (n) PSC values in range 2 is defined as: {(s mod 512), ((s + 1) mod 512), ((s + 2) mod 512) … ((s + n-1) mod 512)}.

alltheRest

This IE is optionally present if the value of IE “Number of PSCs” is not set to “alltheRest”. Otherwise, it is not needed.

CHOICE Configuration info

MP

REL-12

>Continue

(no data)

REL-12

>New configuration

REL-12

>>T330

OP

Integer (5, 10, 20, 30, 60, 120, 180)

Time in minutes. One spare value is needed.

REL-12

>>WLAN Offload Information

MP

WLAN Offload Information

10.3.9b.3

REL-12