Activation time

MP

Integer(0..

255)

CFN [10]

Activation offset

MD

Integer (0..15)

In radio frames. Default value is 0.

REL-13

UE radio access FDD capability update requirement

MP

Boolean

TRUE indicates update required

UE radio access 3.84 Mcps TDD capability update requirement

MP

Boolean

TRUE indicates update required

Name changed in REL-4

UE radio access 7.68 Mcps TDD capability update requirement

MP

Boolean

TRUE indicates update required

REL-7

UE radio access 1.28 Mcps TDD capability update requirement

MP

Boolean

TRUE indicates update required

REL-4

System specific capability update requirement list

OP

1 to <maxSystemCapability>

In this version, a maximum size of 4 of the list shall be applied and any items after the 4^th item in the list shall be ignored.

>System specific capability update requirement

MP

Enumerated (GSM

Five spare values needed.

, GERAN Iu

REL-5

, E-UTRA)

REL-8

Requested E-UTRA Frequency Band list

CV-BCHopt

1 to 16

REL-10

>E-UTRA Frequency band

MP

Integer (1..256)

As defined in [64]. The value of 64 is reserved and shall not be used

REL-10

BCHopt

This IE is not needed when sent in SYSTEM INFORMATION. Otherwise, the IE is optional

Cell update cause

MP

Enumerated (cell reselection, periodical cell update, uplink data transmission, paging response, re-entered service area, radio link failure, RLC unrecoverable error, cellUpdateCause-ext)

Cell update cause Ext

OP

Enumerated (MBMS reception, MBMS ptp RB request, dummy, cellUpdateCause-ext2)

REL-6

Cell update cause Ext2

OP

Enumerated (application layer measurement report available)

Three spare values are needed.

REL-14

Ciphering algorithm

MP

Enumerated (UEA0, UEA1

, UEA2)

REL-7

Ciphering mode command

MP

Enumerated (start/restart)

Ciphering algorithm

MP

Ciphering algorithm 10.3.3.4

Ciphering activation time for DPCH

OP

Activation time

10.3.3.1

Used for radio bearers mapped on RLC-TM. Only applicable if the UE is already in CELL_DCH state

Radio bearer downlink ciphering activation time info

OP

RB activation time info, 10.3.4.13

Used for radio bearers mapped on RLC-AM or RLC-UM
The UTRAN should not include this IE in a message other than a SECURITY MODE COMMAND

CN domain specific DRX cycle length coefficient

MP

Integer(6…9)

Refers to ‘k’ in the formula as specified in [4], Discontinuous reception

Common E-RNTI information

MP

1 to <maxERUCCH>

REL-8

>Starting E-RNTI

MP

E-RNTI 10.3.3.10a

Indicates the starting code of E-RNTI related to a certain E-RUCCH.

REL-8

>Number of group

MP

Integer(1.. maxERNTIgroup)

Indicates the number of common E-RNTI groups related to the E-RUCCH.

REL-8

>Number of E-RNTI per group

MP

Integer

(1.. maxERNTIperGroup)

Indicates the number of common E-RNTIs in the group.

REL-8

C-RNTI

MP

bit string(16)

Support of intra-frequency proximity indication

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support intra-frequency proximity indication

REL-9

Support of inter-frequency proximity indication

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support inter-frequency proximity indication

REL-9

Support of E-UTRA proximity indication

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support E-UTRA proximity indication

REL-9

DSCH-RNTI

MP

bit string(16)

E-RNTI

MP

bit string(16)

REL-6

Establishment cause

MP

Enumerated(

Originating Conversational Call,

Originating Streaming Call,

Originating Interactive Call,

Originating Background Call,

Originating Subscribed traffic Call,

Terminating Conversational Call,

Terminating Streaming Call,

Terminating Interactive Call,

Terminating Background Call,

Emergency Call,

Inter-RAT cell re-selection,

Inter-RAT cell change order,

Registration, Detach,

Originating High Priority Signalling,

Originating Low Priority Signalling,

Call re-establishment,

Terminating High Priority Signalling,

Terminating Low Priority Signalling,

Terminating – cause unknown, MBMS reception, MBMS ptp RB request,

Nine spare values are needed.

Delay Tolerant Access)

REL-10

Expiration Time Factor

MP

Enumerated(

2times, 4times,

8times,

16times, 32times, 64times, 128times, 256times)

Extended Wait time

MP

Integer(1..

1800)

Value in seconds

Expiration Time Factor 2

MP

Integer (0..15)

REL-12

Failure cause

MP

Enumerated (configuration unsupported, physical channel failure, incompatible simultaneous reconfiguration, protocol error, compressed mode runtime error, cell update occurred, invalid configuration, configuration incomplete, unsupported measurement, MBMS session already received correctly, lower priority MBMS service)

Five spare values are needed.

Failure cause

MP

Failure cause 10.3.3.13

Protocol error information

CV-ProtErr

Protocol error information 10.3.8.12

Deleted TGPSI

CV-CompModeErr

TGPSI

10.3.6.82

ProtErr

The IE is mandatory present if the IE "Failure cause" has the value "Protocol error"; otherwise it is not needed in the message.

CompModeErr

The IE is mandatory present if the IE "Failure cause" has the value " Compressed mode runtime error"; otherwise it is not needed in the message

U-RNTI group

MP

U-RNTI group 10.3.3.47a

REL-5

H-RNTI

MP

bit string(16)

REL-5

Voice over UTRA PS HS Support

OP

Enumerated (TRUE)

Absence of this IE means that the UE does not support IMS voice

REL-9

SRVCC Support from UTRA to UTRA

OP

Enumerated (TRUE)

Absence of this IE means that the UE does not support SRVCC from UTRA PS HS to UTRA CS

REL-9

SRVCC Support from UTRA to GERAN

OP

Enumerated (TRUE)

Absence of this IE means that the UE does not support SRVCC from UTRA PS HS to GERAN CS

REL-9

rSRVCC support from UTRA CS to E-UTRAN FDD

OP

Enumerated (TRUE)

Absence of this IE means that the UE does not support rSRVCC from UTRA CS to E-UTRAN FDD

REL-11

rSRVCC support from UTRA CS to E-UTRAN TDD

OP

Enumerated (TRUE)

Absence of this IE means that the UE does not support rSRVCC from UTRA CS to E-UTRAN TDD

REL-11

CHOICE UE id type

MP

>IMSI (GSM-MAP)

IMSI (GSM-MAP) 10.3.1.5

>TMSI and LAI (GSM-MAP)

>>TMSI (GSM-MAP)

MP

TMSI (GSM-MAP) 10.3.1.17

>>LAI (GSM-MAP)

MP

Location Area Identification 10.3.1.7

>P-TMSI and RAI (GSM-MAP)

>>P-TMSI (GSM-MAP)

MP

P-TMSI (GSM-MAP) 10.3.1.13

>>RAI (GSM-MAP)

MP

Routing Area Identification 10.3.1.16

>IMEI

IMEI 10.3.1.4

>ESN (DS-41)

Bit string (SIZE (32))

TIA/EIA/IS-2000-4

>IMSI (DS-41)

Octet string (SIZE (5..7))

TIA/EIA/IS-2000-4

>IMSI and ESN (DS-41)

TIA/EIA/IS-2000-4

>>IMSI (DS-41)

MP

Octet string (SIZE (5..7))

TIA/EIA/IS-2000-4

>>ESN (DS-41)

MP

Bit string (SIZE (32))

TIA/EIA/IS-2000-4

>TMSI (DS-41)

Octet string (SIZE (2..17))

TIA/EIA/IS-2000-4

Although normally upto 12 digits are used for this IE, a bigger length is used to support future extension.

Message authentication code

MP

bit string(32)

MAC-I [40]. The first/leftmost bit of the bit string contains the most significant bit of the MAC-I. The 27 MSB of the IE shall be set to zero and the 5 LSB of the IE shall be set to the value of the IE "RB identity" for the used signalling radio bearer when the encoded RRC message is used as the MESSAGE parameter in the integrity protection algorithm.

RRC Message sequence number

MP

Integer (0..15)

The local RRC hyper frame number (RRC HFN) is concatenated with the RRC message sequence number to form the input parameter COUNT-I for the integrity protection algorithm.

The IE value shall be set to zero when the encoded RRC message is used as the MESSAGE parameter in the integrity protection algorithm.

RRC message sequence number list

MP

4 to 5

The RRC sequence number when a new integrity protection configuration shall be applied, for signalling radio bearers in the order RB0, RB1, RB2, RB3, RB4.

The value for RB1 shall be ignored if this IE was included in a RRC message sent on RB1.

The value for RB2 shall be ignored if this IE was included in a RRC message sent on RB2.

>RRC message sequence number

MP

Integer (0..

15)

Integrity protection algorithm

MP

Enumerated (UIA1

, UIA2)

REL-7

Integrity protection mode command

MP

Enumerated(start, modify)

Downlink integrity protection activation info

CV-modify

Integrity protection activation info 10.3.3.17

Integrity protection algorithm

OP

Integrity protection algorithm 10.3.3.18

Integrity protection initialisation number

CV-start

Bit string(32)

FRESH [40]. The first/leftmost bit of the bit string contains the most significant bit of the FRESH.

Start

The IE is mandatory present if the IE "Integrity protection mode command" has the value "start ", otherwise it is not needed in the message.

Modify

The IE is mandatory present if the IE "Integrity protection mode command" has the value "modify" and not needed otherwise.

Inter-frequency detected set measurements

CV-not_iRAT_HoInfo

Enumerated

(TRUE)

TRUE means that the UE is able to measure inter-frequency detected cells.

REL-10

Cells excluded from detected set measurements

CV-not_iRAT_HoInfo

Enumerated

(TRUE)

TRUE means that the UE is able to exclude cells from detected set measurements.

REL-11

Wideband RSRQ FDD measurements

CV-not_iRAT_HoInfo

Enumerated

(TRUE)

TRUE means that the UE is able to perform wideband RSRQ FDD measurements.

REL-11

Wideband RSRQ TDD measurements

CV-not_iRAT_HoInfo

Enumerated

(TRUE)

TRUE means that the UE is able to perform wideband RSRQ TDD measurements.

REL-11

Event 2g reporting on a configured secondary downlink frequency

CV-not_iRAT_HoInfo

Enumerated

(TRUE)

TRUE means that the UE is able to perform event 2g reporting on a configured secondary downlink frequency.

REL-12

Enhanced UPH reporting

CV-not_iRAT_HoInfo

Enumerated

(TRUE)

TRUE means that the UE is able to perform reporting of filtered UPH measurement.

REL-12

RRC measurement events for UPH reporting

CV-not_iRAT_HoInfo

Enumerated

(TRUE)

TRUE means that the UE is able to perform event 6h and 6i reporting.

REL-14

Increased UE carrier monitoring UTRA

CV-not_iRAT_HoInfo

Enumerated

(TRUE)

TRUE means that the UE supports increased number of UTRA carrier monitoring in connected and idle mode as defined in [19].

REL-12

Increased UE carrier monitoring E-UTRA

CV-not_iRAT_HoInfo

Enumerated

(TRUE)

TRUE means that the UE supports increased number of E-UTRA carrier monitoring in connected and idle mode as defined in [74].

REL-12

Extended RSRQ lower value range

CV-not_iRAT_HoInfo

Enumerated

(TRUE)

TRUE means that the UE supports the extended RSRQ lower value range from -34dB to -19.5dB.

REL-12

RSRQ measurement on all symbols

CV-not_iRAT_HoInfo

Enumerated

(TRUE)

TRUE means that the UE supports the RSRQ measurement on all OFDM symbols and the extended upper RSRQ value range from -3dB to 2.5dB.

REL-12

QoE Measurement Collection for streaming services

CV-not_iRAT_HoInfo

Enumerated (TRUE)

TRUE means that the UE supports QoE Measurement Collection for streaming services.

REL-14

QoE Measurement Collection for MTSI services

CV-not_iRAT_HoInfo

Enumerated (TRUE)

TRUE means that the UE supports QoE Measurement Collection for MTSI services.

REL-15

Need for downlink compressed mode

FDD measurements

MP

Boolean

TRUE means that the UE requires DL compressed mode in order to perform measurements on FDD

3.84 Mcps TDD measurements

CV-3.84_Mcps_tdd_sup

Boolean

TRUE means that the UE requires DL compressed mode in order to perform measurements on 3.84 Mcps TDD

Name changed in REL-4

7.68 Mcps TDD measurements

CV-7.68_Mcps_tdd_sup

Boolean

TRUE means that the UE requires DL compressed mode in order to perform measurements on 7.68 Mcps TDD

REL-7

1.28 Mcps TDD measurements

CV-1.28_Mcps_tdd_sup

Boolean

TRUE means that the UE requires DL compressed mode in order to perform measurements on 1.28 Mcps TDD

REL-4

GSM measurements

CV-gsm_sup

>GSM 900

MP

Boolean

TRUE means that the UE requires DL compressed mode in order to perform measurements on GSM 900

>DCS 1800

MP

Boolean

TRUE means that the UE requires DL compressed mode in order to perform measurements on DCS 1800

>GSM 1900

MP

Boolean

TRUE means that the UE requires DL compressed mode in order to perform measurements on GSM 1900

Multi-carrier measurement

CV-mc_sup

Boolean

TRUE means that the UE requires DL compressed mode in order to perform measurements on multi-carrier

Adjacent Frequency measurements without compressed mode

CV-not_iRAT_HoInfo

Enumerated (TRUE)

TRUE means that the UE does not require compressed mode for adjacent frequency measurements.

REL-8

Inter-band Frequency measurements without compressed mode

CV-not_iRAT_HoInfo

Enumerated (TRUE)

TRUE means that the UE does not require compressed mode for Inter-band measurements for the band combinations reported in the IE “Radio Access Capability Band Combination List”.

REL-9

Enhanced inter-frequency measurements without compressed mode

CV-not_iRAT_HoInfo

Enumerated

(TRUE)

TRUE means that the UE does not require compressed mode for measurements on two additional frequencies

REL-10

Frequency specific compressed mode

CV-not_iRAT_HoInfo

Enumerated (TRUE)

TRUE means that for the dual band operation the UE can apply compressed mode only to the configured frequencies, which belong to the frequency band other than the serving HS-DSCH cell.

REL-10

Inter-frequency measurements on configured carriers without compressed mode

CV-not_iRAT_HoInfo

Enumerated (TRUE)

TRUE means that the UE does not require compressed mode for measurements on the frequencies which are configured for HS-DSCH operation and associated with the secondary serving HS-DSCH cells.

REL-11

Need for uplink compressed mode

FDD measurements

MP

Boolean

TRUE means that the UE requires UL compressed mode in order to perform measurements on FDD

3.84 Mcps TDD measurements

CV-3.84_Mcps_tdd_sup

Boolean

TRUE means that the UE requires UL compressed mode in order to perform measurements on 3.84 Mcps TDD

Name changed in REL-4

7.68 Mcps TDD measurements

CV-7.68_Mcps_tdd_sup

Boolean

TRUE means that the UE requires UL compressed mode in order to perform measurements on 7.68 Mcps TDD

REL-7

1.28 Mcps TDD measurements

CV-1.28_Mcps_tdd_sup

Boolean

TRUE means that the UE requires DL compressed mode in order to perform measurements on 1.28 Mcps TDD

REL-4

GSM measurements

CV-gsm_sup

>GSM 900

MP

Boolean

TRUE means that the UE requires UL compressed mode in order to perform measurements on GSM 900

>DCS 1800

MP

Boolean

TRUE means that the UE requires UL compressed mode in order to perform measurements on DCS 1800

>GSM 1900

MP

Boolean

TRUE means that the UE requires UL compressed mode in order to perform measurements on GSM 1900

Multi-carrier measurement

CV-mc_sup

Boolean

TRUE means that the UE requires UL compressed mode in order to perform measurements on multi-carrier

3.84_Mcps_tdd_sup

The IE is mandatory present if an IE "TDD RF capability" is present with the IE "Chip rate capability" set to "3.84 Mcps". Otherwise this field is not needed in the message.

7.68_Mcps_tdd_sup

The IE is mandatory present if an IE “TDD RF capability” is present with the IE “Chip rate capability” set to “7.68 Mcps”. Otherwise this field is not needed in the message.

1.28_Mcps_tdd_sup

The IE is mandatory present if an IE "TDD RF capability" is present with the IE "Chip rate capability" set to "1.28 Mcps". Otherwise this field is not needed in the message.

gsm_sup

The IE is mandatory present if the IE "Inter-RAT UE radio access capability" indicates support for GSM900, GSM1800 and/or GSM1900. Otherwise this field is not needed in the message.

mc_sup

The IE is mandatory present if the IE "Support of multi-carrier" has the value TRUE. Otherwise this field is not needed in the message.

not_iRAT_HoInfo

The IE is not needed in the INTER RAT HANDOVER INFO message. Otherwise, it is optionally present.

FDD measurements

MP

1 to <maxFreqBandsFDD>

The network should ignore the entry that includes the ‘extension indicator’.

1 to <maxFreqBandsFDD2>

REL-6

1 to <maxFreqBandsFDD3>

REL-10

>FDD Frequency band

CV-fdd2

Enumerated(Band I, Band II,

The default value is the same as indicated in the IE "Frequency band" included in the IE " UE radio access capability extension". Band numbering is defined in [21].

Band III,

REL-5

Band VI, Band IV, Band V, Band VII, extension indicator)

The default value is the same as R99, if the IE “FDD Frequency band 2” below is not included. The setting of the value ‘extension indicator’ by the UE is not specified in the specification.

REL-6

>FDD Frequency band 2

CV-fdd1

Enumerated(Band VIII, Band IX, Band X, Band XI, Band XII, Band XIII, Band XIV, Band XIX, Band XXI, Band XX, Band XXII, extension Indicator)

The default value is the same as indicated in the IE "Frequency band 2" included in the IE " UE radio access capability extension", if the IE “FDD Frequency band” above is not included.

The setting of the value ‘extension indicator’ by the UE is not specified in the specification.

Four spare values are needed

REL-6

>FDD Frequency band 3

OP

Enumerated (Band XXV, Band XXVI, Band XXXII,

extension indicator)

If the IE is not present the value is the same as indicated in the IE "Frequency band 3" if included in the IE " UE radio access capability extension".

The setting of the value ‘extension indicator’ by the UE is not specified in the specification.

Sixty spare

values are needed

REL-10

>Need for DL compressed mode

MP

Boolean

TRUE means that the UE requires DL compressed mode in order to perform measurements on the FDD frequency band indicated by the IE "FDD Frequency band"

>Need for UL compressed mode

MP

Boolean

TRUE means that the UE requires UL compressed mode in order to perform measurements on the FDD frequency band indicated by the IE "FDD Frequency band"

TDD measurements

CV-tdd_sup

1 to <maxFreqBandsTDD>

>TDD Frequency band

MP

Enumerated(a, b, c)

Enumerated(a, b, c, d)

REL-7

>Need for DL compressed mode

MP

Boolean

TRUE means that the UE requires DL compressed mode in order to perform measurements on TDD frequency band indicated by the IE "TDD Frequency band"

>Need for UL compressed mode

MP

Boolean

TRUE means that the UE requires UL compressed mode in order to perform measurements on TDD frequency band indicated by the IE "TDD Frequency band"

GSM measurements

CV-gsm_sup

1 to <maxFreqBandsGSM>

>GSM Frequency band

MP

Enumerated(GSM450, GSM480, GSM850, GSM900P, GSM900E, GSM1800, GSM1900)

as defined in [45].

Nine spare values are needed.

>Need for DL compressed mode

MP

Boolean

TRUE means that the UE requires DL compressed mode in order to perform measurements on GSM frequency band indicated by the IE "GSM Frequency band"

>Need for UL compressed mode

MP

Boolean

TRUE means that the UE requires UL compressed mode in order to perform measurements on GSM frequency band indicated by the IE "GSM Frequency band"

Multi-carrier measurement

CV-mc_sup

>Need for DL compressed mode

MP

Boolean

TRUE means that the UE requires DL compressed mode in order to perform measurements on multi-carrier

>Need for UL compressed mode

MP

Boolean

TRUE means that the UE requires UL compressed mode in order to perform measurements on multi-carrier

E-UTRA measurements

CV-eutra_sup

1 to <maxFreqBandsEUTRA>

Note 1

REL-8

>E-UTRA Frequency band

MP

Integer (1..64)

As defined in [64]. If the IE indicates a value of 64, then the E-UTRA Frequency band for this instance should be read from the corresponding instance of IE "E-UTRA Frequency band extension" in the E-UTRA measurements extension.

REL-8

>Need for compressed mode

MP

Boolean

TRUE means that the UE requires DL and UL compressed mode in order to perform measurements on E-UTRA frequency band indicated by the IE "E-UTRA Frequency band"

REL-8

E-UTRA measurements extension

CV-extended_eutra_sup

1 to <maxFreqBandsEUTRA>

Note 1

REL-11

>E-UTRA Frequency band extension

MP

Integer (65..256)

As defined in [64].

Note 2

REL-11

E-UTRA measurements extension 1

CV- extended_meas_eutra_sup

1 to <maxFreqBandsEUTRA-ext>

Note 1

REL-11

>E-UTRA Frequency band extension 1

MP

Integer (1..256)

As defined in [64]. The value of 64 is reserved and shall not be used.

REL-11

>Need for compressed mode

MP

Boolean

TRUE means that the UE requires DL and UL compressed mode in order to perform measurements on E-UTRA frequency band indicated by the IE "E-UTRA Frequency band extension 1"

REL-11

tdd_sup

The IE is mandatory present if the IE "Multi-mode capability" has the value "TDD" or "FDD/TDD". Otherwise this field is not needed in the message.

gsm_sup

The IE is mandatory present if the IE "Support of GSM" has the value TRUE. Otherwise this field is not needed in the message.

mc_sup

The IE is mandatory present if the IE "Support of multi-carrier" has the value TRUE. Otherwise this field is not needed in the message.

eutra_sup

At least one of these IEs is mandatory present if the IE "Support of E-UTRA" has the value TRUE. Otherwise these fields are not needed in the message.

extended_eutra_sup

At least one of these IEs is mandatory present if the IE "Support of E-UTRA" has the value TRUE and the UE supports a E-UTRA frequency band greater than 64. Otherwise these fields are not needed in the message.

extended_meas_eutra_sup

At least one of these IEs is mandatory present if the IE "Support of E-UTRA" has the value TRUE and the UE needs to report E-UTRA measurement capability for more than 16 E-UTRA bands. Otherwise these fields are not needed in the message.

fdd1

The IE is mandatory default if the IE "FDD Frequency band" is not included in the message. Otherwise this field is not needed in the message.

fdd2

The IE is mandatory default if the IE "FDD Frequency band 2" is not included in the message. Otherwise this field is not needed in the message.

E-UTRA measurements

CV-eutra_sup

1 to <maxFreqBandsEUTRA>

Note 1

REL-8

>E-UTRA Frequency band

MP

Integer (1..64)

As defined in [64]. If the IE indicates a value of 64, then the E-UTRA Frequency band for this instance should be read from the corresponding instance of IE "E-UTRA Frequency band extension" in the E-UTRA measurements extension.

REL-8

>Need for Idle Interval

MP

Boolean

TRUE means that the UE requires idle interval in order to perform measurements on E-UTRA frequency band indicated by the IE "E-UTRA Frequency band"

REL-8

E-UTRA measurements extension

CV-extended_eutra_sup

1 to <maxFreqBandsEUTRA>

Note 1

REL-11

>E-UTRA Frequency band extension

MP

Integer (65..256)

As defined in [64].

Note 2

REL-11

eutra_sup

At least one of these IEs is mandatory present if the IE "Support of E-UTRA" has the value TRUE. Otherwise these fields are not needed in the message.

extended_eutra_sup

At least one of these IEs is mandatory present if the IE "Support of E-UTRA" has the value TRUE and the UE supports a E-UTRA frequency band greater than 64. Otherwise these fields are not needed in the message.

Support for Multiflow with MIMO operation in different bands

OP

Enumerated(single-stream, dual-stream)

Absence of this IE means that a UE does not support MIMO with Multiflow in different bands. Otherwise, it indicates whether a UE support single-stream or dual-stream MIMO.

REL-11

Longer HARQ processing time

OP

Enumerated(TRUE)

Presence of this IE indicates that a UE needs more time to generate the HARQ feedback with Multiflow and MIMO as described in [26], sub-clause 7.7.2.

REL-11

Number of cells

MP

Integer(2..8)

Total number of cells that can be configured to a UE as a part of Multiflow configuration. In this version of the specification, the maximum value is 4.

REL-11

Number of frequencies

MP

Integer(1..4)

Total number of frequencies, across which the Multiflow can be configured.

In this version of the specification, the maximum value is 2.

REL-11

In this version of the specification, the maximum value is 3.

REL-13

MIMO support

OP

Enumerated(single-stream, dual-stream)

Absence of this IE means that a UE does not support MIMO with Multiflow. Otherwise, it indicates whether a UE support single-stream or dual-stream MIMO.

REL-11

Non-contiguous multi-cell

OP

Presence of this IE indicates that a UE supports Multiflow operation with non-contiguous cells.

REL-11

>Gap size

MP

Enumerated(fiveMHz, tenMHz, anyGapSize)

This IE indicates the maximum gap size between the aggregated cells.

"fiveMHz" indicates that UE supports 5 MHz gap size.

"tenMHz" indicates that UE supports 10 MHz gap size and 5 MHz gap size.

"anyGapSize" indicates that UE supports any multiple of 5 MHz gap size.

5 spare values are required.

REL-11

Support of intra-frequency SI acquisition for HO

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support intra-frequency SI acquisition for HO

REL-9

Support of inter-frequency SI acquisition for HO

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support inter-frequency SI acquisition for HO

REL-9

Support of E-UTRA SI acquisition for HO

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support E-UTRA SI acquisition for HO

REL-9

Paging cause

MP

Enumerated(

Terminating Conversational Call,

Terminating Streaming Call,

Terminating Interactive Call,

Terminating Background Call, Terminating High Priority Signalling,

Terminating Low Priority Signalling,

Terminating – cause unknown

)

One spare value is needed.

CHOICE Used paging identity

MP

>CN identity

>>Paging cause

MP

Paging cause 10.3.3.22

>>CN domain identity

MP

CN domain identity 10.3.1.1

>>CHOICE UE Identity

MP

Three spare values are needed.

>>>IMSI (GSM-MAP)

IMSI (GSM-MAP) 10.3.1.5

>>>TMSI (GSM-MAP)

TMSI (GSM-MAP) 10.3.1.17

>>>P-TMSI (GSM-MAP)

P-TMSI (GSM-MAP) 10.3.1.13

>>>IMSI (DS-41)

Octet string (SIZE (5..7))

TIA/EIA/IS-2000-4

>>>TMSI (DS-41)

Octet string (SIZE (2..17))

TIA/EIA/IS-2000-4

>UTRAN single UE identity

>>U-RNTI

MP

U-RNTI 10.3.3.47

>>CN originated page to connected mode UE

OP

>>>Paging cause

MP

Paging cause 10.3.3.22

>>>CN domain identity

MP

CN domain identity 10.3.1.1

>>>Paging record type identifier

MP

Paging record type identifier

10.3.1.10

>>RRC connection release information

MP

RRC connection release information 10.3.3.35o

REL-5

>UTRAN group identity

1 to <maxURNTIgroup>

REL-5

>>RRC connection release information

MP

RRC connection release information 10.3.3.35o

REL-5

>>Group release information

MP

Group release information 10.3.3.14o

REL-5

CHOICE Used paging identity

Condition under which the given used paging identity is chosen

CN identity

For CN originating pages (for idle mode UEs)

UTRAN single UE identity

For UTRAN originating pages (for connected mode UEs), addressing a single UE

UTRAN group identity

For UTRAN originating pages (for connected mode UEs), addressing a group of UEs

Support for lossless SRNS relocation

MP

Boolean

TRUE means supported

Support for lossless DL RLC PDU size change

CV-not_iRAT_HoInfo2

Boolean

TRUE means supported Default value is FALSE

REL-5

Support for RFC2507

MP

Boolean

TRUE means supported

>Max HC context space

MP

Integer(1024, 2048, 4096, 8192,

16384, 32768, 65536, 131072)

Note 1

REL-5

Support for RFC 3095

CV-not_iRAT_HoInfo

Boolean

TRUE means header compression according to IETF ROHC standard [83], [84] is supported

REL-4

>Maximum number of ROHC context sessions

MD

Integer( 2, 4, 8, 12, 16, 24, 32, 48, 64, 128, 256, 512, 1024, 16384)

Default value is 16.

REL-4

>Reverse decompression depth

MD

Integer (0..65535)

Default value is 0 (reverse decompression is not supported).

REL-4

>Support for RFC 3095 context relocation

MP

Boolean

TRUE means supported

REL-5

Support for CS Voice over HSPA

CV-not_iRAT_HoInfo3

Enumerated (TRUE)

The IE indicates the UE’s support for CS Voice over HSPA, if set.

REL-8

not_iRAT_HoInfo

The IE is optionally present in the INTER RAT HANDOVER INFO message. Otherwise, it is mandatory present.

not_iRAT_HoInfo2

The IE is not needed in the INTER RAT HANDOVER INFO message. Otherwise, it is mandatory default.

not_iRAT_HoInfo3

The IE is not needed in the INTER RAT HANDOVER INFO message. Otherwise, it is optionally present.

Downlink physical channel capability information elements

FDD downlink physical channel capability

CH-fdd_req_sup

>Max no DPCH codes

MP

Integer

(1..8)

Maximum number of DPCH codes to be simultaneously received

>Max no physical channel bits received

MP

Integer

(1200, 2400, 3600, 4800, 7200, 9600, 14400, 19200, 28800, 38400, 48000, 57600, 67200, 76800)

Maximum number of physical channel bits received in any 10 ms interval (DPCH, S-CCPCH)

>Support for SF 512 and 80 ms TTI for DPCH

MP

Boolean

TRUE means supported

>Support for DCH Enhancements

CV-not_iRAT_HoInfo2

Enumerated (Basic, Full)

The absence of this IE indicates that the UE does not support DCH Enhancements

REL-12

>Simultaneous support for DCH Enhancements and Compressed Mode operation

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support simultaneous operation of DCH Enhancements and Compressed Mode.

REL-12

>Simultaneous support for DCH Enhancements and DPCCH Discontinuous Transmission

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support simultaneous operation of DCH Enhancements and DPCCH Discontinuous Transmission.

REL-12

>Support of Enhanced Serving Cell Change for Event 1c

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support Enhanced Serving Cell Change for Event 1c operation.

REL-12

>Support of DPCCH2

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support DPCCH2 transmission.

REL-12

>Support of power control algorithm 3

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support power control algorithm 3.

REL-13

>Support of blind HARQ retransmissions for HSDPA

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support blind HARQ retransmissions for HSDPA.

REL-13

>CHOICE Support of HS-PDSCH

CV-not_iRAT_HoInfo

REL-5

>>Supported

REL-5

>>>HS-DSCH physical layer category

MP

Integer

(1..64)

As defined in [35].

Values 13…64 are spares.

See Note 5.

REL-5

>>>HS-DSCH physical layer category extension

OP

Integer (1..20)

As defined in [35].

See Note 6.

REL-7

>>>HS-DSCH physical layer category extension 2

OP

Integer

(21..24)

As defined in [35].

See Note 12. Absence of this IE means that dual cell operation is not supported.

REL-8

>>>HS-DSCH physical layer category extension 3

OP

Integer

(25..28)

As defined in [35].

See Note 13. Absence of this IE means that dual cell operation is not supported with MIMO.

REL-9

>>>HS-DSCH physical layer category extension 4

OP

Integer (29,30)

As defined in [35].

See Note 16.

Absence of this IE means the multi-cell operation on three cells is not supported.

REL-10

>>>HS-DSCH physical layer category extension 5

OP

Integer (31,32)

As defined in [35].

See Note 17.

Absence of this IE means the multi-cell operation on four cells is not supported.

REL-10

>>>HS-DSCH physical layer category extension 6

OP

Integer (33,34)

As defined in [35].

See Note 18.

Absence of this IE means the multi-cell operation on five and /or six cells is not supported.

REL-11

>>>HS-DSCH physical layer category extension 7

OP

Integer (35,36)

As defined in [35].

See Note 19.

Absence of this IE means the multi-cell operation on seven and/or eight cells is not supported.

REL-11

>>>HS-DSCH physical layer category extension 8

OP

Integer (37,38)

As defined in [35].

See Note 20.

Absence of this IE means the MIMO mode with four transmit antennas operation is not supported.

REL-11

>>>HS-SCCHless HS-DSCH operation support

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support HS-SCCHless HS-DSCH operation.

REL-7

>>>Enhanced F-DPCH support

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support enhanced F-DPCH

REL-7

>>>HS-PDSCH in CELL_FACH

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support HS-PDSCH reception in CELL_FACH

REL-7

>>>HS-PDSCH in CELL_PCH and URA_PCH

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support HS-PDSCH in neither CELL_PCH nor URA_PCH states.

REL-7

>>>Target Cell Pre-Configuration

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support HS-SCCH reception in target cell

REL-8

>>>Support of HS-DSCH DRX operation

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support HS-DSCH DRX operation

REL-8

>>>Support of MIMO only with single stream restriction

OP

Enumerated (TRUE)

The presence of this IE means that the UE supports MIMO only with single stream restriction.

REL-9

>>> Non-contiguous multi-cell with MIMO

OP

Enumerated (TRUE)

The presence of this IE means that the UE supports non-contiguous multi-cell with MIMO in the frequency bands where it supports non-contiguous multi-cell operation.

REL-11

>>>Support of MIMO mode with four transmit antennas only with dual stream restriction

OP

Enumerated (TRUE)

The presence of this IE means that the UE supports MIMO mode with four transmit antennas operation only with dual stream restriction.

REL-11

>>>Support of NodeB triggered HS-DPCCH transmission

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support NodeB triggered HS-DPCCH transmission

REL-11

>>>Support of HS-DSCH DRX operation with second DRX cycle

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support HS-DSCH DRX operation with second DRX cycle in CELL_FACH state.

REL-11

>>>Support of Simplified HS-SCCH type 1 operation

OP

Enumerated (TRUE)

The presence of this IE indicates that Simplified HS-SCCH type 1 operation is applicable.

REL-15

>>Unsupported

(no data)

REL-5

>DRX enhancements

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support DRX enhancements.

REL-12

>HS-DPCCH overhead reduction

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support HS-DPCCH overhead reduction for multi-RAB with DCH.

REL-12

>Support of HS-SCCH DRX operation

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support HS-SCCH DRX operation

REL-14

3.84 Mcps TDD downlink physical channel capability

CH-3.84_Mcps_tdd_req_sup

Name changed in REL-4

>Maximum number of timeslots per frame

MP

Integer

(1..14)

>Maximum number of physical channels per frame

MP

Integer

(1..224)

>Minimum SF

MP

Integer (1, 16)

>Support of PDSCH

MP

Boolean

TRUE means supported

>CHOICE Support of HS-PDSCH

CV-not_iRAT_HoInfo

REL-5

>>Supported

REL-5

>>>HS-DSCH physical layer category

MP

Integer

(1..64)

As defined in [35]

REL-5

>>Unsupported

(no data)

REL-5

>Maximum number of physical channels per timeslot

MP

Integer (5..16)

7.68 Mcps TDD downlink physical channel capability

CH-7.68_Mcps_tdd_req_sup

REL-7

>Maximum number of timeslots per frame

MP

Integer

(1..14)

REL-7

>Maximum number of physical channels per frame

MP

Integer

(1..448)

REL-7

>Minimum SF

MP

Integer (1, 32)

REL-7

>Support of PDSCH

MP

Boolean

TRUE means supported

REL-7

>CHOICE Support of HS-PDSCH

CV-not_iRAT_HoInfo

REL-7

>>Supported

REL-7

>>>HS-DSCH physical layer category

MP

Integer

(1..64)

As defined in [35]

REL-7

>>Unsupported

(no data)

REL-7

>Maximum number of physical channels per timeslot

MP

Integer (1..32)

REL-7

1.28 Mcps TDD downlink physical channel capability

CH-1.28_Mcps_tdd_req_sup

REL-4

>Maximum number of timeslots per subframe

MP

Integer (1..6)

REL-4

>Maximum number of physical channels per subframe

MP

Integer (1..96)

REL-4

>Minimum SF

MP

Integer (1, 16)

REL-4

>Support of PDSCH

MP

Boolean

TRUE means supported

REL-4

>CHOICE Support of HS-PDSCH

CV-not_iRAT_HoInfo

REL-5

>>Supported

REL-5

>>>HS-DSCH physical layer category

MP

Integer

(1..64)

As defined in [35]. Values 16…64 are spares.

See Note 8.

REL-5

>>>HS-DSCH physical layer category extension

OP

Integer (1..64)

As defined in [35].

See Note 6.

REL-8

>>>Multi-carrier HS-DSCH physical layer category

OP

Integer

(1..64)

As defined in [35].

Absent if downlink multiple carrier is not supported. Values 45…64 are spares.

See Note 10.

REL-7

>>>Multi-carrier HS-DSCH physical layer category extension

OP

Integer (1..36)

As defined in [35].

Absent if downlink multiple carrier is not supported.

See Note 11.

REL-8

>>>Multi-carrier HS-DSCH physical layer category extension2

OP

Integer (37..64)

This IE shall be used if the Multi-carrier HS-DSCH physical layer category is larger than 36.

Values 45…64 are spares.

See Note 11.

REL-10

>>>Support of SF Mode For HS-PDSCH dual stream

OP

Enumerated (SF1, SF1/SF16)

For,1.28 Mcps TDD only

The absence of this IE indicates that the UE does not support MIMO.

REL-8

>>Unsupported

(no data)

REL-5

>Maximum number of physical channels per timeslot

MP

Integer (1..16)

REL-4

>Support of 8PSK

MP

Boolean

TRUE means supported

REL-4

>Support of non-rectangular resource allocation

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

For 1.28 Mcps TDD only.The absence of this IE indicates that the UE does not support the non-rectangular resource allocation.

REL-12

Uplink physical channel capability information elements

FDD uplink physical channel capability

CH-fdd_req_sup

>Maximum number of DPDCH bits transmitted per 10 ms

MP

Integer (600, 1200, 2400, 4800. 9600, 19200. 28800, 38400, 48000, 57600)

>Support of cell reselection indication reporting

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support the report of Cell Reselection Indication during common E-DCH transmission.

REL-12

>Support of Serving E-DCH cell decoupling

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support Serving E-DCH cell decoupling operation.

REL-12

>Support of Radio Links without DPCH/F-DPCH

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support Radio Links without DPCH/F-DPCH.

REL-12

>CHOICE Support of E-DCH

CV-not_iRAT_HoInfo

REL-6

>>Supported

REL-6

>>>E-DCH physical layer category

MP

Integer (1..16)

As defined in [35] in Rel-6

Values 7 to 16 are spares.

See Note 4.

REL-6

>>>E-DCH physical layer category extension

OP

Integer (7)

As defined in [35].

REL-7

>>>E-DCH physical layer category extension 2

OP

Integer

(8..9)

As defined in [35].

See Note 14. Absence of this IE means that Dual Cell E-DCH operation is not supported.

REL-9

>>>E-DCH physical layer category extension 3

OP

Integer

(10..12)

As defined in [35]. See Note 21.

Absence of this IE means that neither 64 QAM in the uplink nor UL MIMO operation is supported.

REL-11

>>>DPCCH Discontinuous Transmission support

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support DPCCH Discontinuous Transmission

REL-7

>>>Slot Format #4 support

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support Slot Format #4

REL-7

>>Unsupported

(no data)

REL-6

>Access Groups based access control

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support control of DTCH transmissions in CELL_FACH and CELL_PCH.

REL-12

>Enhanced TTI switching

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support Enhanced TTI switching.

REL-12

>Implicit Grant handling

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support Implicit Grants on the Secondary Uplink frequency.

REL-12

>DTX enhancements

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support DTX enhancements.

REL-12

>Support of dual cell E-DCH transmission with DPDCH

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support dual cell E-DCH transmission with DPDCH.

REL-13

>Support of Dual Cell E-DCH operation enhancements

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support Dual Cell E-DCH operation enhancements.

REL-14

3.84 Mcps TDD uplink physical channel capability

CH-3.84_Mcps_tdd_req_sup

Name changed in REL-4

>Maximum Number of timeslots per frame

MP

Integer

(1..14)

>Maximum number of physical channels per timeslot

MP

Integer

(1, 2)

>Minimum SF

MP

Integer

(1, 2, 4, 8)

>Support of PUSCH

MP

Boolean

TRUE means supported

>CHOICE Support of E-DCH

CV-not_iRAT_HoInfo

REL-7

>>Supported

REL-7

>>>E-DCH physical layer category

MP

Integer (1..16)

As defined in [35]

REL-7

>>Unsupported

(no data)

REL-7

7.68 Mcps TDD uplink physical channel capability

CH-7.68_Mcps_tdd_req_sup

REL-7

>Maximum Number of timeslots per frame

MP

Integer

(1..14)

REL-7

>Maximum number of physical channels per timeslot

MP

Integer

(1, 2)

REL-7

>Minimum SF

MP

Integer

(1, 2, 4, 8)

REL-7

>Support of PUSCH

MP

Boolean

TRUE means supported

REL-7

>CHOICE Support of E-DCH

CV-not_iRAT_HoInfo

REL-7

>>Supported

REL-7

>>>E-DCH physical layer category

MP

Integer (1..16)

As defined in [35]

REL-7

>>Unsupported

(no data)

REL-7

1.28 Mcps TDD uplink physical channel capability

CH-1.28_Mcps_tdd_req_sup

REL-4

>Maximum Number of timeslots per subframe

MP

Integer

(1..6)

REL-4

>Maximum number of physical channels per timeslot

MP

Integer

(1, 2,

REL-4

3, 4)

REL-7

>Minimum SF

MP

Integer

(1, 2, 4, 8, 16)

REL-4

>Support of PUSCH

MP

Boolean

TRUE means supported

REL-4

>Support of 8PSK

MP

Boolean

TRUE means supported

REL-4

>CHOICE Support of E-DCH

CV-not_iRAT_HoInfo

REL-7

>>Supported

REL-7

>>>E-DCH physical layer category

MP

Integer (1..6)

As defined in [35]

In case of multi-carrier E-DCH, this IE indicates the capability for each single carrier.

REL-7

>>>Multi-carrier E-DCH physical layer category

OP

Integer (1..8)

As defined in [35]

Absent if multiple carrier E-DCH is not supported.

See Note 15.

REL-10

>>>Maximum number of Carriers for Multi-carrier E-DCH

OP

Enumerated (nf-2, nf-3, nf-6)

One spare value is needed.

REL-10

>>Unsupported

(no data)

REL-7

NOTE 1: Void.

NOTE 2: Void.

NOTE 3: Void.

NOTE 4: All UEs supporting E-DCH should signal a category between 1 and 6 for this IE even if the UE physical capability category is above 6.

NOTE 5: All UEs supporting HS-DSCH should signal a category between 1 and 12 for this IE even if the UE physical capability category is above 12. This IE corresponds to the HS-DSCH category supported by the UE when MAC-ehs is not configured.

NOTE 6: This IE corresponds to the HS-DSCH category supported by the UE when MAC-ehs is configured.

NOTE 7: Void

NOTE 8: All UEs supporting HS-DSCH should signal a category between 1 and 15 for this IE even if the UE physical capability category is above 15. This IE corresponds to the HS-DSCH category supported by the UE when MAC-ehs is not configured.

NOTE 9: Void.

NOTE 10: All UEs supporting multi-carrier HS-DSCH should signal a category between 1 and 18 or 39, 40, 43, 44 for this IE. This IE corresponds to the multi-carrier HS-DSCH category supported by the UE when MAC-ehs is not configured.

NOTE 11: This IE corresponds to the multi-carrier HS-DSCH category supported by the UE when MAC-ehs is configured.

NOTE 12: This IE corresponds to the HS-DSCH category supported by the UE when dual cell operation is configured.

NOTE 13: This IE corresponds to the HS-DSCH category supported by the UE when dual cell operation is configured with MIMO.

NOTE 14: This IE corresponds to the E-DCH category supported by the UE when Dual Cell E-DCH operation is configured.

NOTE 15: This IE corresponds to the E-DCH category supported by the UE when Multi-carrier E-DCH operation is configured.

NOTE 16: This IE corresponds to the HS-DSCH category supported by the UE when it is configured with multi-cell operation on three cells.

NOTE 17: This IE corresponds to the HS-DSCH category supported by the UE when it is configured with multi-cell operation on four cells.

NOTE 18: This IE corresponds to the HS-DSCH category supported by the UE when it is configured with multi-cell operation on five and/or six cells.

NOTE 19: This IE corresponds to the HS-DSCH category supported by the UE when it is configured with multi-cell operation on seven and/or eight cells.

NOTE 20: This IE corresponds to the HS-DSCH category supported by the UE when MIMO mode with four transmit antennas operation is configured.

NOTE 21: This IE corresponds to the E-DCH category supported by the UE when MIMO mode and/or 64QAM is configured.

3.84_Mcps_tdd_req_sup

The IE is mandatory present if the IE "TDD RF capability" is present with the IE "Chip rate capability" set to "3.84 Mcps" and a 3.84 Mcps TDD capability update has been requested in a previous message. Otherwise this field is not needed in the message.

7.68_Mcps_tdd_req_sup

The IE is mandatory present if the IE "TDD RF capability" is present with the IE "Chip rate capability" set to "7.68 Mcps" and a 7.68 Mcps TDD capability update has been requested in a previous message. Otherwise this field is not needed in the message.

1.28_Mcps_tdd_req_sup

The IE is mandatory present if the IE "TDD RF capability" is present with the IE "Chip rate capability" set to "1.28 Mcps" and a 1.28 Mcps TDD capability update has been requested in a previous message. Otherwise this field is not needed in the message.

fdd_req_sup

The IE is mandatory present if the IE "Multi-mode capability" has the value "FDD" or "FDD/TDD" and a FDD capability update has been requested in a previous message. Otherwise this field is not needed in the message.

not_iRAT_HoInfo

The CHOICE Support of HS-PDSCH is not needed in the INTER RAT HANDOVER INFO message. Otherwise, it is mandatory present.

not_iRAT_HoInfo

The CHOICE Support of E-DCH is not needed in the INTER RAT HANDOVER INFO message.

Otherwise, it is mandatory present.

not_iRAT_HoInfo2

The IE is not needed in the INTER RAT HANDOVER INFO message. Otherwise, it is optional.

Support of E-UTRA FDD

MP

Boolean

REL-8

Support of E-UTRA TDD

MP

Boolean

REL-8

Protocol error cause

MP

Enumerated (ASN.1 violation or encoding error, Message type non-existent or not implemented, Message not compatible with receiver state, Information element value not comprehended, Information element missing, Message extension not comprehended)

Two spare values are needed.

Protocol error indicator

MP

Boolean

TRUE means a protocol error occurred. FALSE means a protocol error did not occur.

T314 expired

MP

Boolean

TRUE means that the timer has expired or the stored value is zero.

FALSE means that the timer has not expired.

T315 expired

MP

Boolean

TRUE means that the timer has expired or the stored value is zero.

FALSE means that the timer has not expired.

CHOICE Redirection Information

MP

>Frequency info

Frequency info 10.3.6.36

>Inter-RAT info

Inter-RAT info 10.3.7.25

Re-establishment timer

MP

Enumerated(useT314, useT315)

Rejection cause

MP

Enumerated(congestion, unspecified)

Release cause

MP

Enumerated

(normal event, unspecified, pre-emptive release, congestion, re-establishment reject, directed signalling connection re-establishment, user inactivity)

One spare value is needed.

CHOICE FDD

MP

REL-5

>Supported

REL-5

>>RF capability band FDD list Compressed

MP

1..<maxfreqbandsFDD>

REL-5

1..<maxfreqbandsFDD2>

REL-6

1..<maxfreqbandsFDD3>

REL-10

>>>RF Capability Band FDD Compressed

MP

Enumerated (not supported, default TxRx separation)

TX/RX frequency separation capability for the supported frequency band(s). Default is the TX/RX frequency separation defined in [21] for each frequency band.

Two spare values are needed.

REL-5

>Not supported

NULL

REL-5

CHOICE TDD-3.84Mcps

MP

REL-5

>Supported

REL-5

>>Radio Frequency Band TDD List

MP

Enumerated (a, b, c, a+b, a+c, b+c, a+b+c)

As defined in [22].

One spare value needed

REL-5

Enumerated (a, b, c, d, a+b, a+c, a+d, b+c, b+d, c+d, a+b+c, a+b+d, a+c+d, b+c+d, a+b+c+d)

REL-7

>Not supported

NULL

REL-5

CHOICE TDD-7.68Mcps

MP

REL-7

>Supported

REL-7

>>Radio Frequency Band TDD List

MP

Enumerated (a, b, c, d, a+b, a+c, a+d, b+c, a+b+c, a+b+d, a+c+d, b+c+d, a+b+c+d)

As defined in [22].

One spare value needed

REL-7

>Not supported

NULL

REL-7

CHOICE TDD-1.28Mcps

MP

REL-5

>Supported

REL-5

>>Radio Frequency Band TDD List

MP

Enumerated (a, b, c, a+b, a+c, b+c, a+b+c)

As defined in [22].

One spare value needed

REL-5

Enumerated (a, b, c, d, a+b, a+c, a+d, b+c, b+d, c+d, a+b+c, a+b+d, a+c+d, b+c+d, a+b+c+d)

REL-7

>Not supported

NULL

REL-5

UE power class

MP

Enumerated(1..4)

As defined in [21]

Tx/Rx frequency separation

MP

Enumerated(default TxRx separation)

Default is the TX/RX frequency separation defined in [21] for each frequency band.

Two spare values are needed.

Support of Multiple Frequency Band Indicators

CV-not_iRAT_HoInfo

Enumerated (TRUE)

FDD only.

Absence of this IE means that the UE does not support the signalling requirements of multiple radio frequency bands, as defined in [85], and the UE does not understand the UARFCN signalling for all bands, that overlap with the band(s) supported by the UE.

REL-10

not_iRAT_HoInfo

The IE is not needed in the INTER RAT HANDOVER INFO message. Otherwise, it is optional.

UE power class extension

MP

Enumerated(1..4)

As defined in [21]. A UE with UE power class 3bis signals the value 3. Four spare values are needed

Tx/Rx frequency separation

MP

Enumerated(default TxRx separation)

Default is the TX/RX frequency separation defined in [21] for each frequency band.

Two spare values are needed.

UE power class

MP

Enumerated

(1..4)

as defined in [22]

Radio frequency bands

MP

Enumerated(a, b, c, a+b, a+c, b+c, a+b+c)

as defined in [22].

One spare value needed.

Enumerated (a, b, c, d, a+b, a+c, a+d, b+c, b+d, c+d, a+b+c, a+b+d, a+c+d, b+c+d, a+b+c+d,

REL-7

Notabcd)

as defined in [22].

The value “Notabcd” indicate that the UE does not support neither one of the bands a, b, c nor d.

REL-8

Radio frequency bands extension list

OP

1 to <maxFreqBandsTDD-ext>

as defined in [22].

REL-8

>Radio frequency bands ext

MP

Enumerated (e, f, g, h, i, j, k, l, m, n, o, p)

as defined in [22].

Band g to band p are reserved for future use.

REL-8

Chip rate capability

MP

Enumerated (3.84Mcps, 1.28Mcps,

as defined in [22]

7.68 Mcps)

REL-7

Radio frequency bands

MP

Enumerated(a, b, c, a+b, a+c, b+c, a+b+c)

as defined in [22].

One spare value needed.

Enumerated (a, b, c, d, a+b, a+c, a+d, b+c, b+d, c+d, a+b+c, a+b+d, a+c+d, b+c+d, a+b+c+d)

REL-7

Total RLC AM buffer size

MP

Integer

(10, 50, 100, 150, 500, 1000,

Total receiving and transmitting RLC AM buffer and MAC-hs/ehs reordering buffer capability in kBytes.

Note 1.

Note 2.

200, 300, 400, 750,

REL-5

1150, 1250,

REL-9

1500,

1800,

2300,

2550,

Total receiving and transmitting RLC AM buffer and MAC-hs/ehs reordering buffer capability in kBytes.

Note 2. Four Spare values are needed.

Rel-10

3400,

3500, 4400,

4500,

5000)

REL-11

Maximum RLC AM Window Size

MP

Integer(2047,4095)

Maximum supported RLC TX and RX window in UE

Maximum number of AM entities

MP

Integer

(4,5,6,8,16,30)

Support for Two logical channel Configuration

CV-not_iRAT_HoInfo

Boolean

TRUE means supported

REL-7

not_iRAT_HoInfo

The IE is not needed in the INTER RAT HANDOVER INFO message. Otherwise, it is mandatory present.

RLC re-establish indicator

MP

Boolean

TRUE means re-establish required

FALSE means re-establish not required

RRC State indicator

MP

Enumerated(CELL_DCH, CELL_FACH, CELL_PCH, URA_PCH)

CHOICE Release indicator

MD

Default value is “No release”

REL-5

>No release

REL-5

>Release

REL-5

>>Release cause

MP

Release cause 10.3.3.32

REL-5

CHOICE RRC Tr Id type

MP

REL-5

>Normal

>>RRC transaction identifier

MP

Integer (0..3)

>Extended

REL-5

>>RRC transaction identifier

MP

Integer (0..15)

REL-5

Normal

All cases where the RRC Tr Id type: Extended is not chosen.

Extended

Optional in the MEASUREMENT CONTROL message. Mandatory in the MEASUREMENT CONTROL FAILURE message.

NONCE

OP

Bit string (128)

REL-11

IMS information

MP

Octet String(SIZE(1..32))

Contains ATGW transfer details as defined in [24.237]

REL-11

Ciphering algorithm capability

MP

>UEA0

MP

Boolean

>UEA1

MP

Boolean

>UEA2

MP

Boolean

The value TRUE means that UEA2 is fully interoperability tested.

If fully interoperability tested, also "Security capability indication" of "UE radio access capability compressed" shall be set to TRUE.

REL-7

>Spare

MP

13

Boolean

Shall be set to FALSE by UEs complying with this version of the protocol.

Integrity protection algorithm capability

MP

>UIA1

MP

Boolean

The value TRUE means that UIA1, Kasumi, is supported

>UIA2

MP

Boolean

The value TRUE means that UIA2 is fully interoperability tested.

If fully interoperability tested, also "Security capability indication" of "UE radio access capability compressed" shall be set to TRUE.

REL-7

>Spare

MP

14

Boolean

Shall be set to FALSE by UEs complying with this version of the protocol.

Signallng Connection Release Indication Cause

MP

Enumerated (UE Requested PS Data session end, any other cause)

REL-8

START

MP

Bit string (20)

START [40]. The first/leftmost bit of the bit string contains the most significant bit of the START.

Downlink transport channel capability information elements

Max no of bits received

MP

Integer(640, 1280, 2560, 3840, 5120, 6400, 7680, 8960, 10240, 20480, 40960, 81920, 163840)

Maximum sum of number of bits of all transport blocks received at an arbitrary time instant

Max convolutionally coded bits received

MP

Integer(640, 1280, 2560, 3840, 5120, 6400, 7680, 8960, 10240, 20480, 40960, 81920, 163840)

Maximum sum of number of bits of all convolutionally coded transport blocks received at an arbitrary time instant

Max turbo coded bits received

CV-turbo_dec_sup

Integer(640, 1280, 2560, 3840, 5120, 6400, 7680, 8960, 10240, 20480, 40960, 81920, 163840)

Maximum sum of number of bits of all turbo coded transport blocks received at an arbitrary time instant

Maximum number of simultaneous transport channels

MP

Integer(4, 8, 16, 32)

Maximum number of simultaneous CCTrCH

MP

Integer (1..8)

Max no of received transport blocks

MP

Integer(4, 8, 16, 32, 48, 64, 96, 128, 256, 512)

Maximum total number of transport blocks received within TTIs that end at within the same 10ms interval

Maximum number of TFC

MP

Integer(16, 32, 48, 64, 96, 128, 256, 512, 1024)

Maximum number of TF

MP

Integer(32, 64, 128, 256, 512, 1024)

Support for turbo decoding

MP

Boolean

TRUE means supported

Uplink transport channel capability information elements

Max no of bits transmitted

MP

Integer(640, 1280, 2560, 3840, 5120, 6400, 7680, 8960, 10240, 20480, 40960, 81920, 163840)

Maximum sum of number of bits of all transport blocks transmitted at an arbitrary time instant

Max convolutionally coded bits transmitted

MP

Integer(640, 1280, 2560, 3840, 5120, 6400, 7680, 8960, 10240, 20480, 40960, 81920, 163840)

Maximum sum of number of bits of all convolutionally coded transport blocks transmitted at an arbitrary time instant

Max turbo coded bits transmitted

CV-turbo_enc_sup

Integer(640, 1280, 2560, 3840, 5120, 6400, 7680, 8960, 10240, 20480, 40960, 81920, 163840)

Maximum sum of number of bits of all turbo coded transport blocks transmitted at an arbitrary time instant

Maximum number of simultaneous transport channels

MP

Integer(4, 8, 16, 32)

Maximum number of simultaneous CCTrCH of DCH type

CH-tdd_req_sup

Integer (1..8)

Max no of transmitted transport blocks

MP

Integer(4, 8, 16, 32, 48, 64, 96, 128, 256, 512)

Maximum total number of transport blocks transmitted within TTIs that start at the same time

Maximum number of TFC

MP

Integer(16, 32, 48, 64, 96, 128, 256, 512, 1024)

Maximum number of TF

MP

Integer(32, 64, 128, 256, 512, 1024)

Support for turbo encoding

MP

Boolean

TRUE means supported

turbo_dec_sup

The IE is mandatory present if the IE "Support of turbo decoding" = TRUE. Otherwise this field is not needed in the message.

turbo_enc_sup

The IE is mandatory present if the IE "Support of turbo encoding" = TRUE. Otherwise this field is not needed in the message.

tdd_req_sup

The IE is mandatory present if the IE "Multi-mode capability" has the value "TDD" or "FDD/TDD" and a TDD capability update has been requested in a previous message. Otherwise this field is not needed in the message.

Multi-RAT capability

Support of GSM

MP

Boolean

Support of multi-carrier

MP

Boolean

Multi-mode capability

MP

Enumerated (TDD, FDD, FDD/TDD)

Support of UTRAN to GERAN NACC

CV-not_iRAT_HoInfo

Boolean

REL-5

Support of Handover to GAN

CV-not_iRAT_HoInfo2

Enumerated (DoesSupportHandoverToGAN)

Absence of this IE means that the UE does not support Handover to GAN.

REL-6

Support of Inter-RAT PS handover

CV-not_iRAT_HoInfo2

Enumerated (DoesSupportInter-RAT-PS-Handover)

Absence of this IE means that the UE does not support Inter-RAT PS Handover to GERAN

REL-6

Support of PS Handover to GAN

CV-not_iRAT_HoInfo2

Enumerated (DoesSupportPSHandoverToGAN)

Absence of this IE means that the UE does not support PS Handover to GAN.

REL-7

Support of E-UTRA FDD

CV-not_iRAT_HoInfo2

Enumerated (DoesSupportEUTRAFDD)

Absence of this IE means that the UE does not support E-UTRA FDD

REL-8

Support of Inter-RAT PS Handover to E-UTRA FDD

CV-not_iRAT_HoInfo2

Enumerated (DoesSupportInter-RATHOToEUTRAFDD)

Absence of this IE means that the UE does not support Inter-RAT PS Handover to E-UTRA FDD

REL-8

Support of E-UTRA TDD

CV-not_iRAT_HoInfo2

Enumerated (DoesSupportEUTRATDD)

Absence of this IE means that the UE does not support E-UTRA TDD

REL-8

Support of Inter-RAT PS Handover to E-UTRA TDD

CV-not_iRAT_HoInfo2

Enumerated (DoesSupportInter-RATHOToEUTRATDD)

Absence of this IE means that the UE does not support Inter-RAT PS Handover to E-UTRA TDD

REL-8

EUTRA Feature Group Indicators

CV-not_iRAT_HoInfo2

Bit string (4)

The definitions of the bits are described in Annex E

REL-8

Support of E-UTRA Multiple Frequency Band Indicators

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

Absence of this IE means that the UE does not support the signalling requirements of multiple radio frequency bands in E-UTRA, as defined in [67], and the UE does not understand the EARFCN signalling for all bands, that overlap with the band(s) supported by the UE.

REL-10

Support of E-UTRA FDD measurements and reporting in CELL_FACH

CV-not_iRAT_HoInfo2

Enumerated (DoesSupportEUTRAmeasurementsandreportinginCELLFACH)

Absence of this IE means that the UE does not support E-UTRA measurement for CELL_FACH for E-UTRA FDD

REL-11

Support of E-UTRA TDD measurements and reporting in CELL_FACH

CV-not_iRAT_HoInfo2

Enumerated (DoesSupportEUTRAmeasurementsandreportinginCELLFACH)

Absence of this IE means that the UE does not support E-UTRA measurement for CELL_FACH for E-UTRA TDD

REL-11

Support of RAN-assisted WLAN interworking based on RAN rules

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

Absence of this IE means that the UE does not support RAN-assisted WLAN interworking based on access network selection and traffic steering rules.

REL-12

Support of RAN-assisted WLAN interworking based on ANDSF policies

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

Absence of this IE means that the UE does not support RAN-assisted WLAN interworking based on ANDSF policies.

REL-12

Support of extended E-UTRA frequency priority

CV-not_iRAT_HoInfo2

Enumerated (TRUE)

Absence of this IE means that the UE does not support extended E-UTRA priority.

REL-13

not_iRAT_HoInfo

The IE is not needed in the INTER RAT HANDOVER INFO message. Otherwise, it is mandatory present.

not_iRAT_HoInfo2

The IE is not needed in the INTER RAT HANDOVER INFO message. Otherwise, it is optional.

Access stratum release indicator

MP

Enumerated (R99)

Indicates the release of the UE according to [35]. The IE also indicates the release of the RRC transfer syntax supported by the UE.

CV-not_rrc_connectionSetupComplete

Enumerated(REL-4,

3 spare values are needed.

REL-4

REL-5,

REL-5

REL-6,

REL-6

REL-7,

REL-7

REL-8,

REL-8

REL-9,

REL-9

REL-10,

REL-10

REL-11,

REL-11

REL-12,

REL-12

REL-13,

REL-13

REL-14,

REL-14

REL-15,

REL-15

REL-16)

REL-16

DL capability with simultaneous HS-DSCH configuration

CV-not_iRAT_HoInfo

Enumerated(32kbps, 64kbps, 128kbps, 384kbps)

REL-5

PDCP capability

MP

PDCP capability 10.3.3.24

RLC capability

MP

RLC capability 10.3.3.34

Transport channel capability

MP

Transport channel capability 10.3.3.40

RF capability FDD

OP

RF capability FDD 10.3.3.33

RF capability TDD

OP

RF capability TDD 10.3.3.33b

One "TDD RF capability" entity shall be included for every Chip rate capability supported.

1 to 2

Note 1

REL-4

RF capability TDD 1.28 Mcps

CV-iRAT_HoInfo

RF capability TDD 1.28 Mcps 10.3.3.33c

Note 1

REL-4

Physical channel capability

MP

Physical channel capability 10.3.3.25

UE multi-mode/multi-RAT capability

MP

UE multi-mode/multi-RAT capability 10.3.3.41

Security capability

MP

Security capability 10.3.3.37

UE positioning capability

MP

UE positioning capability 10.3.3.45

Measurement capability

OP

Measurement capability 10.3.3.21

Measurement capability TDD

OP

Measurement capability TDD 10.3.3.21b

REL-8

Device type

MD

Enumerated (DoesNotBenefitFromBatteryConsumptionOptimisation)

Absence of this value means that the device does benefit from NW-based battery consumption optimisation.

UE may set the value to

DoesNotBenefitFromBatteryConsumptionOptimisation when it does not foresee to particularly benefit from NW-based

The IE is not needed in the INTER RAT HANDOVER INFO message.

REL-6

Support for System Information Block type 11bis

OP

Enumerated (TRUE)

REL-6

The IE shall be present and set to TRUE

REL-7

Support for F-DPCH

CV-SupportForHS

Enumerated (TRUE)

Presence of this information element indicates that F-DPCH is supported by the UE.

Absence of this information element indicates that F-DPCH is not supported

REL-6

MAC-ehs support

OP

Enumerated (TRUE)

The presence of this IE indicates that UE supports MAC-ehs, the use of special value of HE field to indicate end of an SDU for RLC AM, octet aligned transport block table and different HS-SCCHs in contiguous TTIs.

The absence of this IE indicates that the UE does not support either MAC-ehs, octet aligned transport block table or the use of special value of HE field to indicate end of an SDU for RLC AM or different HS-SCCHs in contiguous TTIs.

REL-7

UE specific capability Information LCR TDD

OP

Enumerated (NF, TriRxUniTx, TriRxTriTx, HexRxUniTx, HexRxTriTx, HexRxHexT,

For 1.28 Mcps TDD only

REL-7

TwoRxUniTxDiscontiguous, TwoRxTwoTxDiscontiguous, TwoRxUniTxContiguous, TwoRxTwoTxContiguous)

TwoRxUniTxDiscontiguous and TwoRxTwoTxDiscontiguous mean that the UE is capable of supporting two non-adjacent carriers. TwoRxUniTxContiguous and TwoRxTwoTxContiguous mean that the UE is only capable of supporting two adjacent carriers. 6 spare values needed. Note 3.

REL-10

Support for E-DPCCH Power Boosting

OP

Enumerated

(TRUE)

The

absence of this IE indicates that the E-DPCCH Power Boosting is not supported. The presence of this IE indicates that the E-DPCCH Power Boosting is supported by the UE.

REL-7

Support of common E-DCH

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support E-DCH enhanced random access in CELL_FACH state and Idle mode.

REL-8

Support of MAC-i/is

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support MAC-i/is operation.

REL-8

Support of Common E-RGCH based interference control

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support Common E-RGCH based interference control in CELL_FACH state.

REL-11

Support of Fallback to R99 PRACH

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support Fallback to R99 PRACH in CELL_FACH state and IDLE mode.

REL-11

Support of Concurrent deployment

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support Concurrent deployment of 2ms and 10ms TTI in a cell in CELL_FACH state and IDLE mode.

REL-11

Support of TTI alignment and Per HARQ process

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support TTI alignment and Per HARQ process activation and de-activation in CELL_FACH state and IDLE mode.

REL-11

Support of SPS operation

CV-not_iRAT_HoInfo

Enumerated (TRUE)

For 1.28 Mcps TDD only.

The absence of this IE indicates that the UE does not support SPS operation.

REL-8

Support of Control Channel DRX operation

CV-not_iRAT_HoInfo

Enumerated (TRUE)

For 1.28 Mcps TDD only.

The absence of this IE indicates that the UE does not support Control Channel DRX operation

REL-8

Support of CSG

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support access control based on CSG

REL-8

Support for Two DRX schemes in URA_PCH and CELL_PCH

OP

Enumerated

(TRUE)

The absence of this IE indicates that the UE does not support Two DRX schemes in URA_PCH and CELL_PCH

REL-7

Support for E-DPDCH power interpolation formula

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support E-DPDCH power interpolation formula when 16QAM is not configured

REL-7

Support for absolute priority based cell re-selection in UTRAN

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support absolute priority based cell re-selection to UTRA inter-frequency

REL-8

Support of MU-MIMO

OP

Enumerated (Uplink, Uplink and Downlink)

The absence of this IE indicates that the UE does not support MU-MIMO. This IE is used for 1.28 Mcps TDD only

REL-10

Radio Access Capability Band Combination List

OP

1 to 16

The absence of this IE indicates that the UE does not support Dual Band Operation.

REL-9

>Band Combination

MP

Integer(1..256)

The integer value n indicates that the n^th DB-DC Configuration (A,B) in table 5.0AA in [21] is supported by the UE.

REL-9

>Support for Dual Band Dual Cell E-DCH operation

OP

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support Dual Band Dual Cell E-DCH operation on the corresponding band combination indicated by the IE "Band Combination".

REL-13

>Supported Carrier Combination

OP

Absence of this IE means that the UE only supports the carrier combination (1,1) for this band combination (A,B). If carrier combination (X,Y) is supported, then carrier combination (M,N) is supported, where 1<=M<=X and 1<=N<=Y, so the corresponding value for that carrier combination (M,N) should be set to TRUE.

Carrier combination (X,Y) for a band combination (A,B) refers to a block of X contiguous carriers in Band A and a block of Y contiguous carriers in Band B.

REL-10

>>Carrier Combination (1,2)

MP

Boolean

The value TRUE means that carrier combination (1,2) is supported for this band combination (A,B).

REL-10

>>Carrier Combination (2,1)

MP

Boolean

The value TRUE means that carrier combination (2,1) is supported for this band combination (A,B).

REL-10

>>Carrier Combination (1,3)

MP

Boolean

The value TRUE means that carrier combination (1,3) is supported for this band combination (A,B).

REL-10

>>Carrier Combination (3,1)

MP

Boolean

The value TRUE means that carrier combination (3,1) is supported for this band combination (A,B).

REL10

>>Carrier Combination (2,2)

MP

Boolean

The value TRUE means that carrier combination (2,2) is supported for this band combination (A,B).

REL-10

>>Carrier Combination (1,4)

MP

Boolean

The value TRUE means that carrier combination (1,4) is supported for this band combination (A,B).

REL-11

>>Carrier Combination (4,1)

MP

Boolean

The value TRUE means that carrier combination (4,1) is supported for this band combination (A,B).

REL-11

>>Carrier Combination (1,5)

MP

Boolean

The value TRUE means that carrier combination (1,5) is supported for this band combination (A,B).

REL-11

>>Carrier Combination (5,1)

MP

Boolean

The value TRUE means that carrier combination (5,1) is supported for this band combination (A,B).

REL11

>>Carrier Combination (1,6)

MP

Boolean

The value TRUE means that carrier combination (1,6) is supported for this band combination (A,B).

REL-11

>>Carrier Combination (6,1)

MP

Boolean

The value TRUE means that carrier combination (6,1) is supported for this band combination (A,B).

REL-11

>>Carrier Combination (1,7)

MP

Boolean

The value TRUE means that carrier combination (1,7) is supported for this band combination (A,B).

REL-11

>>Carrier Combination (7,1)

MP

Boolean

The value TRUE means that carrier combination (7,1) is supported for this band combination (A,B).

REL-11

>>Carrier Combination (2,3)

MP

Boolean

The value TRUE means that carrier combination (2,3) is supported for this band combination (A,B).

REL11

>>Carrier Combination (3,2)

MP

Boolean

The value TRUE means that carrier combination (3,2) is supported for this band combination (A,B).

REL-11

>>Carrier Combination (2,4)

MP

Boolean

The value TRUE means that carrier combination (2,4) is supported for this band combination (A,B).

REL-11

>>Carrier Combination (4,2)

MP

Boolean

The value TRUE means that carrier combination (4,2) is supported for this band combination (A,B).

REL-11

>>Carrier Combination (2,5)

MP

Boolean

The value TRUE means that carrier combination (2,5) is supported for this band combination (A,B).

REL-11

>>Carrier Combination (5,2)

MP

Boolean

The value TRUE means that carrier combination (5,2) is supported for this band combination (A,B).

REL11

>>Carrier Combination (2,6)

MP

Boolean

The value TRUE means that carrier combination (2,6) is supported for this band combination (A,B).

REL-11

>>Carrier Combination (6,2)

MP

Boolean

The value TRUE means that carrier combination (6,2) is supported for this band combination (A,B).

REL-11

>>Carrier Combination (3,3)

MP

Boolean

The value TRUE means that carrier combination (3,3) is supported for this band combination (A,B).

REL-11

>>Carrier Combination (3,4)

MP

Boolean

The value TRUE means that carrier combination (3,4) is supported for this band combination (A,B).

REL-11

>>Carrier Combination (4,3)

MP

Boolean

The value TRUE means that carrier combination (4,3) is supported for this band combination (A,B).

REL11

>>Carrier Combination (4,4)

MP

Boolean

The value TRUE means that carrier combination (4,4) is supported for this band combination (A,B).

REL11

>>Carrier Combination (3,5)

MP

Boolean

The value TRUE means that carrier combination (3,5) is supported for this band combination (A,B).

REL-11

>>Carrier Combination (5,3)

MP

Boolean

The value TRUE means that carrier combination (5,3) is supported for this band combination (A,B).

REL-11

>Supported Multiflow Combination

OP

Presence of this IE indicates that UE supports Multiflow for this band combination. Note 5.

REL-11

Note 6

REL-13

>>Number of cells in band A

MP

Integer(1..6)

Total number of cells in band A that can be configured to a UE as a part of Multiflow configuration. In this version of the specification, the maximum value is 2.

REL-11

In this version of the specification, the maximum value is 3.

REL-13

>>Number of frequencies in band A

MP

Integer(1..3)

Total number of frequencies in band A, across which the Multiflow can be configured. In this version of the specification, the maximum value is 1.

REL-11

In this version of the specification, the maximum value is 2.

REL-13

>>Number of cells in band B

MP

Integer(1..6)

Total number of cells in band B that can be configured to a UE as a part of Multiflow configuration. In this version of the specification, the maximum value is 2.

REL-11

>>Number of frequencies in band B

MP

Integer(1..3)

Total number of frequencies in band B, across which the Multiflow can be configured. In this version of the specification, the maximum value is 1.

REL-11

Support of multi-cell configuration in inter-RAT handover

CV-iRAT_HoInfo

Enumerated (TRUE)

REL-11

Support of TX Diversity on DL Control Channels by MIMO Capable UE when MIMO operation is active

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the MIMO capable UE does not support TX diversity on DL Control Channels (HS-SCCH, F-DPCH, E-AGCH, E-HICH, E-RGCH) when MIMO is active, P-CPICH is configured on antenna 1, and S-CPICH on antenna 2.

REL-7

The absence of this IE indicates that the MIMO capable UE does not support TX diversity on DL Control Channels (HS-SCCH, F-DPCH, E-AGCH, E-HICH, E-RGCH, F-TPICH) when MIMO is active, P-CPICH is configured on antenna 1, and S-CPICH on antenna 2.

REL-11

Support of enhanced TS0

OP

Enumerated (TRUE)

For 1.28 Mcps TDD only.

The absence of this IE indicates that the UE does not support the enhanced TS0

REL-9

Support for cell-specific Tx diversity configuration for dual-cell operation

CV-

Dual_Cell_HSDPA_supported

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support cell-specific Tx diversity configuration when configured for dual-cell operation.

REL-8

CSG proximity indication capability

CV-not_iRAT_HoInfo

CSG proximity indication capability 10.3.3.8a

REL-9

Neighbour Cell SI acquisition capability

CV-not_iRAT_HoInfo

Neighbour Cell SI acquisition capability 10.3.3.21c

REL-9

Extended measurements Support

CV-not_iRAT_HoInfo

Enumerated

(TRUE)

TRUE means that the UE supports the extended measurement identity range 17 to 32.

REL-9

Support for dual cell with MIMO operation in different bands

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support dual cell with MIMO operation in different bands

REL-10

UE based network performance measurements parameters

CV-not_iRAT_HoInfo

UE based network performance measurements parameters 10.3.3.53

REL-10

Support of UTRAN ANR

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support UTRAN ANR.

REL-10

IMS Voice capability

CV-not_iRAT_HoInfo

IMS Voice capability 10.3.3.14b

REL-9

Multiflow capability

CV-not_iRAT_HoInfo

UE Multiflow capability 10.3.3.21ba

REL-11

Support of MAC-ehs window size extension

OP

Enumerated (TRUE)

For 1.28 Mcps TDD only, the absence of this IE indicates that the UE does not support IE "MAC-ehs window size extension".

Note 4.

REL-9

Support of UM RLC re-establishment via reconfiguration

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support UM RLC re-establishment via reconfiguration.

REL-10

Support of HS-DPCCH power offset extension

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support the HS-DPCCH power offset extension.

REL-11

Support of STTD on DL Control Channels when Multiflow operation is active

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that a Multiflow capable UE does not support STTD on DL Control Channels (HS-SCCH, F-DPCH, E-AGCH, E-HICH, E-RGCH, F-TPICH) when Multiflow operation is active.

REL-11

Support of F-TPICH feedback from the Multiflow assisting cell

CV-not_iRAT_HoInfo

Enumerated(TRUE)

The absence of this IE indicates that the UE does not support reception of the F-TPICH feedback from the Multiflow assisting cell.

REL-12

Support of DSAC and PPAC update in CELL_DCH

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support DSAC and PPAC update in CELL_DCH.

REL-12

Support of retrievable configurations

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support retrievable configurations.

REL-13

Support of URA_PCH with seamless transition

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support URA_PCH with seamless transition.

REL-13

Support of improved synchronized RRC procedures

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support improved synchronized RRC procedures.

REL-13

Support of enhanced state transition

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support enhanced state transition.

REL-13

Support of simultaneous setup and release of RABs and RBs

CV-not_iRAT_HoInfo

Enumerated (TRUE)

The absence of this IE indicates that the UE does not support simultaneous setup and release of RABs and RBs.

REL-14

not_rrc_connectionSetupComplete

The IE is not needed in the RRC CONNECTION SETUP COMPLETE message. Otherwise the IE is mandatory present.

not_iRAT_HoInfo

The IE is not needed in the INTER RAT HANDOVER INFO message. Otherwise, it is optional.

iRAT_HoInfo

The IE is optional in the INTER RAT HANDOVER INFO message. Otherwise, the IE is not needed.

Dual_Cell_HSDPA_supported

This IE is optionally present if Dual-Cell HSDPA is supported. Otherwise it is not needed.

The IE is not needed in the INTER RAT HANDOVER INFO message. Otherwise, it is optional.

SupportForHS

This IE is mandatory present if the UE supports HS-PDSCH, otherwise it is not needed. The IE is not needed in the INTER RAT HANDOVER INFO message.

Access stratum release indicator

MP

Enumerated (R99, REL-4, REL-5,

3 spare values are needed.

REL-5

REL-6,

REL-6

REL-7,

REL-7

REL-8,

REL-8

REL-9,

REL-9

REL-10,

REL-10

REL-11,

REL-11

REL-12,

REL-12

REL-13,

REL-13

REL-14,

REL-14

REL-15,

REL-15

REL-16)

REL-16

Total AM RLC buffer size exceeds 10 kByte

MP

BOOLEAN

REL-5

RF capability compressed

MP

RF capability compressed 10.3.3.32a

REL-5

Support for System Information Block type 11bis

OP

Enumerated (TRUE)

REL-6

The IE shall be present and set to TRUE

REL-7

MAC-ehs support

OP

Enumerated (TRUE)

The presence of this IE indicates that UE supports MAC-ehs, the use of special value of HE field to indicate end of an SDU for RLC AM, octet aligned transport block table and different HS-SCCHs in contiguous TTIs.

Absent if either MAC-ehs, octet aligned transport block table or the use of special value of HE field to indicate end of an SDU for RLC AM or different HS-SCCHs in contiguous TTIs are not supported

REL-7

Security capability indication

OP

Enumerated (TRUE)

TRUE indicates UE security capabilities beyond R99 requirements, see 10.3.3.37

REL-7

GANSS support indication

OP

Enumerated (TRUE)

TRUE indicates that the UE supports GANSS

REL-7

FDD physical channel capability for HS-PDSCH/E-DCH

OP

Absent if HS-PDSCH and E-DCH are not supported

REL-6

>DL capability with simultaneous HS-DSCH configuration

OP

Enumerated (32, 64, 128, 384)

Unit: kbps.

This IE is always required, but the need is set to OP to align with ASN.1

REL-6

>HS-DSCH physical layer category

MP

Integer (1..64)

As defined in [35]

Values 13…64 are spare.

REL-6

>HS-DSCH physical layer category extension

OP

Integer (1..20)

As defined in [35].

See Note 1.

REL-7

>HS-DSCH physical layer category extension 2

OP

Integer (21..24)

As defined in [35].

See Note 2.

REL-8

>HS-DSCH physical layer category extension 3

OP

Integer (25..28)

As defined in [35].

See Note 3.

REL-9

>HS-DSCH physical layer category extension 4

OP

Integer (29,30)

As defined in [35].

See Note 4.

REL-10

>HS-DSCH physical layer category extension 5

OP

Integer (31,32)

As defined in [35].

See Note 5.

REL-10

>HS-DSCH physical layer category extension 6

OP

Integer (33,34)

As defined in [35].

See Note 6.

REL-11

>HS-DSCH physical layer category extension 7

OP

Integer (35,36)

As defined in [35].

See Note 7.

REL-11

>HS-DSCH physical layer category extension 8

OP

Integer (37,38)

As defined in [35].

See Note 8.

REL-11

>CHOICE Support of E-DCH

MP

REL-6

>>Supported

REL-6

>>>E-DCH physical layer category

MP

Integer (1..16)

As defined in [35]

REL-6

>>>E-DCH physical layer category extension

OP

Integer (7)

As defined in [35].

REL-7

>>>E-DCH physical layer category extension 2

OP

Integer

(8..9)

As defined in [35].

REL-9

>>>E-DCH physical layer category extension 3

OP

Integer(10..12)

As defined in [35].

REL-11

>>Unsupported

(no data)

REL-6