B.1 Idle lengths for DL, UL and DL+UL compressed mode for DPCH
25.2123GPPMultiplexing and channel coding (FDD)Release 17TS
Table B.1: Parameters for DL compressed mode
TGL |
DL Frame |
Spreading Factor |
Idle length [ms] |
Transmission time Reduction method |
Idle frame Combining |
3 |
A |
512 – 4 |
1.73 – 1.99 |
Spreading factor division by 2 or Higher layer scheduling |
(S) (D) =(1,2) or (2,1) |
B |
1.60 – 1.86 |
||||
4 |
A |
2.40 – 2.66 |
(S) (D) =(1,3), (2,2) or (3,1) |
||
B |
2.27 – 2.53 |
||||
5 |
A |
3.07 – 3.33 |
(S) (D) = (1,4), (2,3), (3, 2) or (4,1) |
||
B |
2.93 – 3.19 |
||||
7 |
A |
4.40 – 4.66 |
(S) (D)=(1,6), (2,5), (3,4), (4,3), (5,2) or (6,1) |
||
B |
4.27 – 4.53 |
||||
10 |
A |
6.40 – 6.66 |
(D)=(3,7), (4,6), (5,5), (6,4) or (7,3) |
||
B |
6.27 – 6.53 |
||||
14 |
A |
9.07 – 9.33 |
(D) =(7,7) |
||
B |
8.93 – 9.19 |
Table B.2: Parameters for UL compressed mode
TGL |
Spreading Factor |
Idle length [ms] |
Transmission time Reduction method |
Idle frame Combining |
3 |
256 – 4 |
2.00 |
Spreading factor division by 2 or Higher layer scheduling |
(S) (D) =(1,2) or (2,1) |
4 |
2.67 |
(S) (D) =(1,3), (2,2) or (3,1) |
||
5 |
3.33 |
(S) (D) = (1,4), (2,3), (3, 2) or (4,1) |
||
7 |
4.67 |
(S) (D)=(1,6), (2,5), (3,4), (4,3), (5,2) or (6,1) |
||
10 |
6.67 |
(D)=(3,7), (4,6), (5,5), (6,4) or (7,3) |
||
14 |
9.33 |
(D) =(7,7) |
Table B.3: Parameters for combined UL/DL compressed mode
TGL |
DL Frame |
Spreading Factor |
Idle length [ms] |
Transmission time Reduction method |
Idle frame Combining |
3 |
A or B |
DL: UL: 256 – 4 |
1.47 – 1.73 |
Spreading factor division by 2 or Higher layer scheduling |
(S) (D) =(1,2) or (2,1) |
4 |
2.13 – 2.39 |
(S) (D) =(1,3), (2,2) or (3,1) |
|||
5 |
2.80 – 3.06 |
(S) (D) = (1,4), (2,3), (3, 2) or (4,1) |
|||
7 |
4.13 – 4.39 |
(S) (D)=(1,6), (2,5), (3,4), (4,3), (5,2) or (6,1) |
|||
10 |
6.13 – 6.39 |
(D)=(3,7), (4,6), (5,5), (6,4) or (7,3) |
|||
14 |
8.80 – 9.06 |
(D) =(7,7) |
(S): Single-frame method as shown in figure 14 (1).
(D): Double-frame method as shown in figure 14 (2). (x,y) indicates x: the number of idle slots in the first frame, y: the number of idle slots in the second frame.
NOTE: Compressed mode by spreading factor reduction is not supported when SF=4 is used in normal mode
Annex C (informative):
Change history
Change history |
|||||||
---|---|---|---|---|---|---|---|
Date |
TSG # |
TSG Doc. |
CR |
Rev |
Subject/Comment |
Old |
New |
RP_05 |
RP-99588 |
– |
Approved at TSG RAN #5 and placed under Change Control |
– |
3.0.0 |
||
14/01/00 |
RP_06 |
RP-99680 |
001 |
3 |
Correction of rate matching parameters for repetition after 1st unterleaving in 25.212 |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99680 |
004 |
– |
Changing the initial offset value for convolutional code rate matching |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99681 |
005 |
1 |
Introduction of compressed mode by higher layer scheduling |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99679 |
008 |
– |
Editorial corrections to TS 25.212 |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99680 |
009 |
– |
Removal of SFN multiplexing |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99680 |
010 |
1 |
Clarification of bit separation and collection |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99680 |
011 |
2 |
Connection between TTI and CFN |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99680 |
012 |
2 |
Zero length transport blocks |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99679 |
014 |
– |
Update of channel coding sections |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99680 |
016 |
– |
Removal of TrCH restriction in DSCH CCTrCH |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99681 |
017 |
– |
20 ms RACH message length |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99680 |
018 |
– |
Minimum SF in UL |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99680 |
024 |
– |
Rate matching parameter determination in DL and fixed positions |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99680 |
026 |
1 |
Corrections to TS 25.212 |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99679 |
027 |
– |
Modification of BTFD description in 25.212 Annex |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99681 |
028 |
– |
TFCI coding and mapping including compressed mode |
3.0.0 |
3.1.0 |
14/01/00 |
– |
– |
– |
Change history was added by the editor |
3.1.0 |
3.1.1 |
|
31/03/00 |
RP_07 |
RP-000061 |
025 |
2 |
CR for parity bit attachment to 0 bit transport block |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
029 |
1 |
Limitations of blind transport format detection |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
034 |
1 |
Clarification of fixed position rate matching |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
035 |
1 |
Clarification of DL compressed mode |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
036 |
– |
Reconfiguration of TFCS |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
037 |
1 |
Removal of fixed gap position in 25.212 |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
038 |
2 |
Definition clarification for TS 25.212 |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
039 |
1 |
Clarification on TFCI coding input |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
041 |
2 |
Correction of UL compressed mode by higher layer scheduling |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
042 |
5 |
Downlink Compressed Mode by puncturing |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
044 |
– |
Modification of Turbo code internal interleaver |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
045 |
– |
Editorial corrections |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
046 |
– |
SF/2 method: DTX insertion after 2nd interleaver |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
047 |
1 |
TFCI coding for FDD |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
048 |
– |
Mapping of TFCI in downlink compressed mode |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
049 |
– |
Editorial changes to Annex A |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
050 |
– |
Removal of rate matching attribute setting for RACH |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
052 |
– |
Padding Function for Turbo coding of small blocks |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
055 |
2 |
Clarifications relating to DSCH |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000061 |
056 |
– |
Editorial modification of uplink shifting parameter calculation for turbo code puncturing |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000062 |
059 |
1 |
Revision: Editorial correction to the calculation of Rate Matching parameters |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000062 |
060 |
1 |
Editorial changes of channel coding section |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000062 |
061 |
– |
Removal of DL compressed mode by higher layer scheduling with fixed positions |
3.1.1 |
3.2.0 |
26/06/00 |
RP_08 |
RP-000266 |
066 |
1 |
Clause 4.4.5 and table 9 is moved to informative annex |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000266 |
068 |
– |
Editorial modifications of 25.212 |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000266 |
069 |
– |
Removal of BTFD for flexible positions in Release 99 |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000266 |
070 |
1 |
Editorial modifications |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000266 |
071 |
1 |
Corrections and editorial modifications of 25.212 for 2nd insertion of DTX bits for CM |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000266 |
072 |
4 |
Corrections to 25.212 (Rate Matching, p-bit insertion, PhCH segmentation) |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000266 |
073 |
– |
Editorial correction in 25.212 coding/multiplexing |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000266 |
074 |
2 |
Bit separation of the Turbo encoded data |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000266 |
076 |
1 |
Revision of code block segmentation description |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000266 |
077 |
– |
Clarifications for TFCI coding |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000266 |
078 |
2 |
Clarifying the rate matching parameter setting for the RACH and BCH |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000266 |
080 |
– |
Clarification on BTFD utilisation (single CCTrCH) |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000266 |
081 |
– |
Correction of order of checking TFC during flexible position RM parameter determination |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000266 |
082 |
– |
Editorial corrections in channel coding section |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000266 |
083 |
– |
Correction for bit separation and bit collection |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000266 |
084 |
1 |
Correction on the spreading factor selection for the RACH |
3.2.0 |
3.3.0 |
23/09/00 |
RP_09 |
RP-000341 |
079 |
– |
Clarification of compressed mode terminology |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000341 |
085 |
1 |
Editorial corrections in Turbo code internal interleaver section |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000341 |
086 |
1 |
Clarification on DL slot format for compressed mode by SF/2 |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000341 |
087 |
– |
Corrections |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000341 |
088 |
1 |
Clarifications to TS 25.212 |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000341 |
089 |
– |
Correction regarding DSCH |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000341 |
090 |
– |
Correction regarding CPCH |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000341 |
092 |
1 |
Bit separation and collection for rate matching |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000341 |
093 |
– |
Puncturing Limit definition in WG1 specification |
3.3.0 |
3.4.0 |
15/12/00 |
RP_10 |
RP-000538 |
094 |
2 |
Correction of BTFD limitations |
3.4.0 |
3.5.0 |
15/12/00 |
RP_10 |
RP-000538 |
096 |
– |
Compressed mode by puncturing |
3.4.0 |
3.5.0 |
15/12/00 |
RP_10 |
RP-000538 |
097 |
– |
Clarification on the Ci formula |
3.4.0 |
3.5.0 |
15/12/00 |
RP_10 |
RP-000538 |
099 |
– |
Editorial modification in RM section |
3.4.0 |
3.5.0 |
15/12/00 |
RP_10 |
RP-000538 |
100 |
1 |
Editorial corrections in TS 25.212 |
3.4.0 |
3.5.0 |
15/12/00 |
RP_10 |
RP-000538 |
101 |
– |
Correction to code block segmentation |
3.4.0 |
3.5.0 |
16/03/01 |
RP_11 |
– |
– |
– |
Approved as Release 4 specification (v4.0.0) at TSG RAN #11 |
3.5.0 |
4.0.0 |
15/06/01 |
RP_12 |
RP-010332 |
106 |
– |
Correction of compressed mode by puncturing |
4.0.0 |
4.1.0 |
15/06/01 |
RP_12 |
RP-010332 |
108 |
1 |
Dual transport format detection |
4.0.0 |
4.1.0 |
15/06/01 |
RP_12 |
RP-010332 |
112 |
1 |
Correction for downlink rate matching for the DSCH |
4.0.0 |
4.1.0 |
21/09/01 |
RP_13 |
RP-010519 |
115 |
– |
Correction of PDSCH spreading factor signalling |
4.1.0 |
4.2.0 |
14/12/01 |
RP_14 |
RP-010737 |
118 |
– |
Clarification of compressed mode |
4.2.0 |
4.3.0 |
14/12/01 |
RP_14 |
RP-010737 |
122 |
– |
Support of multiple CCTrChs of dedicated type |
4.2.0 |
4.3.0 |
08/03/02 |
RP_15 |
RP-020231 |
128 |
2 |
Removal of channel coding option “no coding” for FDD |
4.3.0 |
4.4.0 |
08/03/02 |
RP_15 |
RP-020054 |
123 |
4 |
Inclusion of flexible hard split mode TFCI operation |
4.3.0 |
5.0.0 |
08/03/02 |
RP_15 |
RP-020058 |
126 |
1 |
Changes to 25.212 for HSDPA work item |
4.3.0 |
5.0.0 |
07/06/02 |
RP_16 |
RP-020308 |
136 |
– |
Downlink bit mapping |
5.0.0 |
5.1.0 |
07/06/02 |
RP_16 |
RP-020316 |
130 |
5 |
Correction of Errata noted by RAN1 delegates |
5.0.0 |
5.1.0 |
07/06/02 |
RP_16 |
RP-020316 |
131 |
2 |
Removal of inconsistencies and ambiguities in the HARQ description |
5.0.0 |
5.1.0 |
07/06/02 |
RP_16 |
RP-020316 |
132 |
– |
Rate Matching and Channel Coding for HS-SCCH |
5.0.0 |
5.1.0 |
07/06/02 |
RP_16 |
RP-020316 |
137 |
– |
Basis sequences for HS-DPCCH Channel Quality information code |
5.0.0 |
5.1.0 |
07/06/02 |
RP_16 |
RP-020316 |
145 |
5 |
UE specific masking for HS-SCCH part1 |
5.0.0 |
5.1.0 |
14/09/02 |
RP_17 |
RP-020582 |
141 |
1 |
Bit scrambling for HS-DSCH |
5.1.0 |
5.2.0 |
15/09/02 |
RP_17 |
RP-020582 |
148 |
Physical channel mapping for HS-DPCCH |
5.1.0 |
5.2.0 |
|
15/09/02 |
RP_17 |
RP-020582 |
149 |
HARQ bit collection |
5.1.0 |
5.2.0 |
|
15/09/02 |
RP_17 |
RP-020582 |
150 |
1 |
Coding for HS-SCCH |
5.1.0 |
5.2.0 |
15/09/02 |
RP_17 |
RP-020582 |
151 |
Correction to UE specific masking for HS-SCCH part1 |
5.1.0 |
5.2.0 |
|
15/09/02 |
RP_17 |
RP-020568 |
155 |
2 |
Clarification of the definition of layer 1 transport channel numbers |
5.1.0 |
5.2.0 |
15/09/02 |
RP_17 |
RP-020573 |
157 |
Numbering Corrections |
5.1.0 |
5.2.0 |
|
15/09/02 |
RP_17 |
RP-020645 |
158 |
1 |
Specification of H-RNTI to UE identity mapping |
5.1.0 |
5.2.0 |
20/12/02 |
RP_18 |
RP-020846 |
163 |
– |
Correction of CQI index to bit mapping |
5.2.0 |
5.3.0 |
20/12/02 |
RP_18 |
RP-020846 |
164 |
– |
Correction of mapping of HARQ-ACK |
5.2.0 |
5.3.0 |
26/03/03 |
RP_19 |
RP-030134 |
165 |
1 |
Correction of CQI index to bit mapping |
5.3.0 |
5.4.0 |
26/03/03 |
RP_19 |
RP-030134 |
166 |
3 |
Correction of bit scrambling of HS-DSCH |
5.3.0 |
5.4.0 |
26/03/03 |
RP_19 |
RP-030134 |
Correction of subscript for modulation scheme information |
5.3.0 |
5.4.0 |
||
23/06/03 |
RP_20 |
RP-030272 |
172 |
1 |
Clarification of TPC and Pilot transmission with STTD in compressed mode |
5.4.0 |
5.5.0 |
23/06/03 |
RP_20 |
RP-030272 |
173 |
2 |
Correction on the flexible TFCI coding in the DSCH hard split mode for Rel5 |
5.4.0 |
5.5.0 |
21/09/03 |
RP_21 |
RP-030456 |
178 |
4 |
Clarification on Single Transport Format Detection |
5.5.0 |
5.6.0 |
21/09/03 |
RP_21 |
RP-030456 |
179 |
– |
Correction on table number in first interleave description |
5.5.0 |
5.6.0 |
21/09/03 |
RP_21 |
RP-030456 |
180 |
3 |
Broadening the conditions that require UEs to perform BTFD for the case of HS-DSCH reception |
5.5.0 |
5.6.0 |
06/01/04 |
RP_22 |
RP-030647 |
183 |
– |
Clarification of the CRC attachment procedure for HS-SCCH |
5.6.0 |
5.7.0 |
06/01/04 |
RP_22 |
RP-030647 |
184 |
1 |
Correction of UE identity notation |
5.6.0 |
5.7.0 |
06/01/04 |
RP_22 |
RP-030644 |
185 |
– |
HARQ process identifier mapping |
5.6.0 |
5.7.0 |
06/01/04 |
RP_22 |
RP-030712 |
186 |
Alignment of terminology across 3GPP documentation |
5.6.0 |
5.7.0 |
|
13/01/04 |
RP_22 |
– |
– |
– |
Created for M.1457 update |
5.7.0 |
6.0.0 |
23/03/04 |
RP_23 |
RP-040085 |
187 |
1 |
CCTrCH definition extension to HS-DSCH |
6.0.0 |
6.1.0 |
09/06/04 |
RP_24 |
RP-040230 |
191 |
1 |
Clarification of Channelization Code-Set Mapping |
6.1.0 |
6.2.0 |
13/12/04 |
RP_26 |
RP-040446 |
192 |
2 |
Introduction of MBMS Soft Combining |
6.2.0 |
6.3.0 |
13/12/04 |
RP_26 |
RP-040527 |
195 |
– |
Preamble and Postamble to reduce HS-DPCCH transmit power |
6.2.0 |
6.3.0 |
13/12/04 |
RP_26 |
RP-040449 |
196 |
2 |
Introduction of E-DCH |
6.2.0 |
6.3.0 |
14/03/05 |
RP_27 |
RP-050088 |
193 |
1 |
Introduction of F-DPCH |
6.3.0 |
6.4.0 |
14/03/05 |
RP_27 |
RP-050044 |
198 |
1 |
PLnon-max and PLmax |
6.3.0 |
6.4.0 |
14/03/05 |
RP_27 |
RP-050045 |
199 |
– |
HARQ bit collection for E-DCH |
6.3.0 |
6.4.0 |
16/06/05 |
RP_28 |
RP-050241 |
203 |
– |
Correction of HSDPA Bit Separation |
6.4.0 |
6.5.0 |
16/06/05 |
RP_28 |
RP-050252 |
204 |
2 |
E-DCH Corrections |
6.4.0 |
6.5.0 |
16/06/05 |
RP_28 |
RP-050252 |
205 |
1 |
Compressed mode operation for the Enhanced Uplink |
6.4.0 |
6.5.0 |
16/06/05 |
RP_28 |
RP-050357 |
206 |
1 |
E-HICH and E-RGCH serving/non-serving definition clarification |
6.4.0 |
6.5.0 |
16/06/05 |
RP_28 |
RP-050250 |
208 |
1 |
Feature Clean Up: Removal of “CPCH” |
6.4.0 |
6.5.0 |
16/06/05 |
RP_28 |
RP-050248 |
210 |
– |
Feature Clean Up: Removal of DSCH (FDD mode) |
6.4.0 |
6.5.0 |
16/06/05 |
RP_28 |
RP-050243 |
212 |
1 |
Feature Clean-Up: Removal of 80 ms TTI for DCH for all other cases but when the UE supports SF512 |
6.4.0 |
6.5.0 |
16/06/05 |
RP_28 |
RP-050252 |
215 |
– |
Clarification on E-AGCH bit mapping |
6.4.0 |
6.5.0 |
16/06/05 |
RP_28 |
RP-050252 |
216 |
– |
Determination of SF and number of PhCHs considering SF2 |
6.4.0 |
6.5.0 |
16/06/05 |
RP_28 |
RP-050251 |
217 |
1 |
MBMS related corrections |
6.4.0 |
6.5.0 |
16/06/05 |
RP_28 |
RP-050249 |
218 |
1 |
Feature clean up: Removal of the ‘compressed mode by puncturing’ |
6.4.0 |
6.5.0 |
16/06/05 |
RP_28 |
RP-050252 |
219 |
– |
Re-ordering of the E-DPCCH bit mapping |
6.4.0 |
6.5.0 |
16/06/05 |
RP_28 |
RP-050252 |
220 |
– |
Coding for E‑AGCH |
6.4.0 |
6.5.0 |
26/09/05 |
RP_29 |
RP-050450 |
0222 |
– |
SF max for E-DPDCH |
6.5.0 |
6.6.0 |
26/09/05 |
RP_29 |
RP-050450 |
0223 |
1 |
Compressed mode operation for the Enhanced Uplink |
6.5.0 |
6.6.0 |
26/09/05 |
RP_29 |
RP-050450 |
0225 |
1 |
Absolute grant values |
6.5.0 |
6.6.0 |
26/09/05 |
RP_29 |
RP-050450 |
0227 |
– |
Removal of description on RSN setting |
6.5.0 |
6.6.0 |
12/12/05 |
RP_30 |
RP-050727 |
0228 |
– |
PLmax alignment over all UE categories |
6.6.0 |
6.7.0 |
12/12/05 |
RP_30 |
RP-050727 |
0229 |
– |
Correction of SF when a CCTrCH is mapped onto four E-DPDCHs |
6.6.0 |
6.7.0 |
12/12/05 |
RP_30 |
RP-050727 |
0231 |
1 |
Usage of 2xSF4 with puncturing |
6.6.0 |
6.7.0 |
20/03/06 |
RP_31 |
– |
– |
– |
Creation of Release 7 specification (v.7.0.0) at RAN#31 |
6.7.0 |
7.0.0 |
12/06/06 |
RP_32 |
RP-060370 |
0236 |
– |
Clarification of E-TFCI terminology |
7.0.0 |
7.1.0 |
29/09/06 |
RP_33 |
RP-060490 |
0240 |
– |
Correction to the E-DCH HARQ rate matching for compressed mode |
7.1.0 |
7.2.0 |
11/12/06 |
RP_34 |
RP-060727 |
0244 |
1 |
Clarification on the number of physical channels, transmission gap positioning and physical channel mapping for E-DCH in relation to compressed mode |
7.2.0 |
7.3.0 |
07/03/07 |
RP_35 |
RP-070115 |
0238 |
5 |
Support of CPC feature |
7.3.0 |
7.4.0 |
07/03/07 |
RP_35 |
RP-070114 |
0241 |
4 |
Coding of HS-SCCH to support FDD MIMO |
7.3.0 |
7.4.0 |
07/03/07 |
RP_35 |
RP-070114 |
0242 |
7 |
Coding of HS-DPCCH to support operation of FDD MIMO |
7.3.0 |
7.4.0 |
07/03/07 |
RP_35 |
RP-070116 |
0245 |
4 |
Introduction of 64QAM for HSDPA |
7.3.0 |
7.4.0 |
30/05/07 |
RP_36 |
RP-070387 |
0249 |
– |
MIMO HS-SCCH rate matching |
7.4.0 |
7.5.0 |
30/05/07 |
RP_36 |
RP-070387 |
0248 |
1 |
Correction to coding of HS-SCCH to support FDD MIMO |
7.4.0 |
7.5.0 |
30/05/07 |
RP_36 |
RP-070387 |
0251 |
1 |
HS-SCCH orders in MIMO mode |
7.4.0 |
7.5.0 |
30/05/07 |
RP_36 |
RP-070388 |
0246 |
5 |
Introduction of 16QAM for HSUPA |
7.4.0 |
7.5.0 |
30/05/07 |
RP_36 |
RP-070384 |
0247 |
1 |
Support for DL only SFN operation for MBMS FDD |
7.4.0 |
7.5.0 |
11/09/07 |
RP_37 |
RP-070644 |
0252 |
– |
16QAM modulation selection for HSUPA |
7.5.0 |
7.6.0 |
11/09/07 |
RP_37 |
RP-070642 |
0253 |
– |
Clarifications of MIMO |
7.5.0 |
7.6.0 |
11/09/07 |
RP_37 |
RP-070641 |
0254 |
– |
Clarifications of CPC and MIMO |
7.5.0 |
7.6.0 |
27/11/07 |
RP_38 |
RP-070941 |
0257 |
– |
Correction of decimal to binary mapping in case of type B CQI |
7.6.0 |
7.7.0 |
27/11/07 |
RP_38 |
RP-070941 |
0259 |
– |
Correction of number of TBs in a TTI in case of MIMO |
7.6.0 |
7.7.0 |
28/11/07 |
RP_38 |
RP-070950 |
0256 |
– |
HS-SCCH information field mapping for 64QAM MIMO |
7.7.0 |
8.0.0 |
05/04/08 |
RP_39 |
RP-080146 |
0261 |
– |
Correction to RV-coding in case of simultaneous usage of 64QAM and MIMO |
8.0.0 |
8.1.0 |
28/05/08 |
RP_40 |
RP-080440 |
0262 |
1 |
HS-SCCH orders for HS-SCCH-less operation |
8.1.0 |
8.2.0 |
28/05/08 |
RP_40 |
RP-080349 |
0264 |
2 |
Clarification to number of HS-PDSCH codes in HS-SCCH less operations |
8.1.0 |
8.2.0 |
09/09/08 |
RP_41 |
RP-080673 |
270 |
2 |
Introduction of HS-PDSCH Serving Cell Change Enhancements |
8.2.0 |
8.3.0 |
09/09/08 |
RP_41 |
RP-080665 |
272 |
– |
Correction to the table name and the quoted name |
8.2.0 |
8.3.0 |
03/12/08 |
RP_42 |
RP-080989 |
267 |
5 |
Introduction of Dual-Cell HSDPA Operation on Adjacent Carriers |
8.3.0 |
8.4.0 |
03/12/08 |
RP_42 |
RP-080988 |
270 |
3 |
Introduction of HS-PDSCH Serving Cell Change Enhancements |
8.3.0 |
8.4.0 |
03/03/09 |
RP_43 |
RP-090228 |
274 |
1 |
Correction to the puncturing limit allowed when UL 4PAM modulation is allowed |
8.4.0 |
8.5.0 |
15/09/09 |
RP_45 |
RP-090885 |
278 |
1 |
Reservation of HS-SCCH order combination not used by CPC |
8.5.0 |
8.6.0 |
15/09/09 |
RP_45 |
RP-090889 |
280 |
1 |
Alignment with RAN2 decisions on HS-SCCH orders for activation and deactivation of DTX and DRX operation |
8.5.0 |
8.6.0 |
18/09/09 |
RP_45 |
RP-090975 |
276 |
4 |
Introduction of TxAA extension for non-MIMO UEs |
8.6.0 |
9.0.0 |
18/09/09 |
RP_45 |
RP-090974 |
282 |
1 |
Combination of DC-HSDPA with MIMO |
8.6.0 |
9.0.0 |
01/12/09 |
RP_46 |
RP-091170 |
281 |
2 |
Introduction of DC-HSUPA |
9.0.0 |
9.1.0 |
01/12/09 |
RP_46 |
RP-091171 |
283 |
3 |
MIMO configuration per downlink frequency in DC-MIMO operation |
9.0.0 |
9.1.0 |
16/03/10 |
RP_47 |
RP-100206 |
286 |
1 |
Clarification of MIMO configuration per downlink frequency in DC-MIMO operation |
9.1.0 |
9.2.0 |
14/09/10 |
RP_49 |
RP-100897 |
287 |
1 |
Clarification of uplink frequencies |
9.2.0 |
9.3.0 |
16/09/10 |
RP_49 |
RP-100902 |
288 |
3 |
Release 10 created with the introduction of 4C-HSDPA |
9.3.0 |
10.0.0 |
07/12/10 |
RP_50 |
RP-101318 |
290 |
3 |
Clarification of 4C-HSDPA |
10.0.0 |
10.1.0 |
07/12/10 |
RP_50 |
RP-101318 |
295 |
– |
4C-HSDPA summary of CQI reporting configurations |
10.0.0 |
10.1.0 |
05/12/11 |
RP_54 |
RP-111671 |
296 |
8 |
Introduction of 8C-HSDPA |
10.1.0 |
11.0.0 |
05/12/11 |
RP_54 |
RP-111672 |
297 |
1 |
Introduction of Uplink Closed Loop Transmit Diversity for HSPA |
10.1.0 |
11.0.0 |
28/02/12 |
RP_55 |
RP-120280 |
301 |
– |
Clarification to Target cell HS-SCCH order type |
11.0.0 |
11.1.0 |
28/02/12 |
RP_55 |
RP-120284 |
303 |
– |
Correction to 4C-HSDPA CQI report mapping scenarios table |
11.0.0 |
11.1.0 |
28/02/12 |
RP_55 |
RP-120287 |
304 |
1 |
Introduction of 8C-HSDPA CQI report mapping scenarios table |
11.0.0 |
11.1.0 |
28/02/12 |
RP_55 |
RP-120288 |
305 |
– |
Corrections to Uplink Closed Loop Transmit Diversity |
11.0.0 |
11.1.0 |
13/06/12 |
RP_56 |
RP-120740 |
307 |
1 |
Addition of missing 8C-HSDPA CQI reporting case indices |
11.1.0 |
11.2.0 |
13/06/12 |
RP_56 |
RP-120741 |
306 |
– |
Clarification of CLTD Features |
11.1.0 |
11.2.0 |
04/09/12 |
RP_57 |
RP-121271 |
308 |
2 |
Introduction of Multiflow |
11.2.0 |
11.3.0 |
04/09/12 |
RP_57 |
RP-121267 |
310 |
1 |
Correction of the number of CQI information bits for MC-HSDPA |
11.2.0 |
11.3.0 |
04/09/12 |
RP_57 |
RP-121268 |
311 |
– |
Correction of HS-SCCH order information |
11.2.0 |
11.3.0 |
04/09/12 |
RP_57 |
RP-121270 |
314 |
– |
Introduction of Further Enhancements to CELL_FACH |
11.2.0 |
11.3.0 |
04/12/12 |
RP_58 |
RP-121845 |
312 |
5 |
Introduction of uplink MIMO and 64QAM |
11.3.0 |
11.4.0 |
04/12/12 |
RP_58 |
RP-121843 |
313 |
5 |
Introduction of 4Tx_HSDPA in 25.212 |
11.3.0 |
11.4.0 |
04/12/12 |
RP_58 |
RP-121840 |
316 |
1 |
Clarification of HS-SCCH order for MC-HSPA |
11.3.0 |
11.4.0 |
04/12/12 |
RP_58 |
RP-121844 |
317 |
1 |
Clarifications and corrections to HSDPA Multiflow |
11.3.0 |
11.4.0 |
04/12/12 |
RP_58 |
RP-121842 |
318 |
1 |
Clarification of HS-SCCH order information |
11.3.0 |
11.4.0 |
11/06/13 |
RP_60 |
RP-130745 |
319 |
2 |
Correction to the HS-SCCH Type 4 Structure |
11.4.0 |
11.5.0 |
11/06/13 |
RP_60 |
RP-130748 |
320 |
1 |
Clarification of HS-SCCH orders with the UE is configured in Multiflow and CLTD |
11.4.0 |
11.5.0 |
03/09/13 |
RP_61 |
RP-131245 |
321 |
– |
Correction of HS-SCCH type 4 order |
11.5.0 |
11.6.0 |
03/03/14 |
RP_63 |
RP-140285 |
326 |
– |
Correction of HS-SCCH type 4 orderCorrection to HS-SCCH special information mapping for HS-SCCH less HSDPA |
11.6.0 |
11.7.0 |
10/09/14 |
RP_65 |
RP-141483 |
327 |
2 |
Introduction of Further EUL Enhancements |
11.7.0 |
12.0.0 |
10/09/14 |
RP_65 |
RP-141482 |
328 |
2 |
Introduction of Enhanced Broadcast of System Information |
11.7.0 |
12.0.0 |
10/09/14 |
RP_65 |
RP-141480 |
329 |
4 |
Introduction of DCH Enhancements |
11.7.0 |
12.0.0 |
10/09/14 |
RP_65 |
RP-141481 |
330 |
1 |
Introduction of UMTS Heterogeneous Networks enhancements |
11.7.0 |
12.0.0 |
08/12/14 |
RP_66 |
RP-142101 |
332 |
1 |
Correction of DL FET |
12.0.0 |
12.1.0 |
08/12/14 |
RP_66 |
RP-142101 |
333 |
– |
Correction to TFCI bit mapping index in Rel-12 DCH Enhancements |
12.0.0 |
12.1.0 |
14/09/15 |
RP_69 |
RP-151469 |
334 |
6 |
Introduction of the Multiflow 3F-4C configuration |
12.1.0 |
13.0.0 |
Change history |
|||||||
Date |
Meeting |
TDoc |
CR |
Rev |
Cat |
Subject/Comment |
New version |
2016-06 |
RP-72 |
RP-161144 |
0340 |
F |
Clarifications on DCH enhancements feature |
13.1.0 |
|
2016-06 |
RP-72 |
RP-161283 |
0338 |
2 |
F |
Clarification on UL DPCH 10ms Mode |
13.1.0 |
2016-12 |
RP-74 |
RP-162354 |
0344 |
– |
B |
Introduction of HS-SCCH Order for HS-SCCH DRx feature in enhanced Cell Fach |
14.0.0 |
2016-12 |
RP-74 |
RP-162363 |
0345 |
1 |
B |
Introduction of multi-carrier enhancements for UMTS |
14.0.0 |
2017-09 |
RP-77 |
RP-171592 |
0347 |
– |
B |
Introduction of the HS-SCCH orders for the additional triggering mechanism based on HS-SCCH orders |
15.0.0 |
2020-07 |
RP-88e |
– |
– |
– |
– |
Upgrade to Rel-16 version without technical change |
16.0.0 |
2022-03 |
RP-95e |
– |
– |
– |
– |
Upgrade to Rel-17 version without technical change |
17.0.0 |