H.4 Transmitted carrier power

25.1413GPPBase Station (BS) conformance testing (FDD)Release 17TS

1) Set the BS to transmit with the maximum transmission power and measure the output power at the antenna connector, PMTP. Maximum transmission power is the mean power on one carrier measured at the antenna connector with the code level settings that according to the base station manufacturer will result in an output power of nominally the maximum output power in a specified reference condition. Test model 2, clause 6.1.1.2, when the code powers are set according to table 6.3. shall be used.

2) Operate the BS in closed loop power control until the output power has reached a stable state. Measure the output power, Pout, at the antenna connector and record the transmitted carrier power measured and reported in the BS, Prep. Note that Prep is normalised to the output power measured in Test Model 2 with all codes at their default levels. If STTD or closed loop transmit diversity is supported by the BS, only the highest of the transmit powers is reported to higher layers. In case of TX diversity or MIMO transmission both branches need to be measured in order to find out which one is the highest.

3) Check that the Pout meets the requirement in TS 25.133 chapter 9.2.4.1, with the same test equipment accuracy as in chapter 6.4.4. in TS 25.141. Prep can be accepted if Pout will fullfill the following conditions:

[ dBm]

4) Repeat step 2 and 3 over the 5%-95% range of the Prep. Use first the standard code powers of test model 2 to verify the Prep range from 50% to 95%. After that put the other dedicated channels off and reduce the powers of the control codes in order to be able to verify the Prep range from 5% to 50%.

NOTE: Pout shall be tested immediately after PMTP in order to avoid the influence of long term stability variation to measurement results.

Annex I (normative):
Characteristics of the W-CDMA interference signal

The W-CDMA interference signal shall be a DPCH containing the DPCCH and one DPDCH. The data content for each channelization code shall be uncorrelated with each other and to the wanted signal and spread and modulated according to clause 4 of TS25.213 [14]. Further characteristics of DPDCH and DPCCH are specified in table I.1.

Table I.1.: Characteristics of the W-CDMA interference signal

Channel

Bit Rate

Spreading Factor

Channelization Code

Relative Power

DPDCH

240 kbps

16

4

0 dB

DPCCH

15 kbps

256

0

-5.46 dB

NOTE: The DPDCH and DPCCH settings are chosen to simulate a signal with realistic Peak to Average Ratio.

Annex J (informative):
Change history

Date

Meeting

TDoc

CR

Rev

Cat

Subject/Comment

New version

RP-37

Rel-8 version created based on v7.9.0

8.0.0

RP-37

RP-070658

0461

B

Introduction of UMTS1500 requirements

8.0.0

RP-38

RP-070936

0466

1

A

Base Station MIMO corrections

8.1.0

RP-38

RP-070937

0468

A

Spurious emissions limits for coexistance with CDMA850

8.1.0

RP-39

RP-080120

0478

A

Correction to RX spurious emissions

8.2.0

RP-39

RP-080122

0473

1

A

Editorial modifications of the test requirement table for the demodulation of E-DPDCH in multipath fading conditions and table and figure title in A.18 in 25.141

8.2.0

RP-39

RP-080124

0471

1

B

Introduction of UMTS700 requirements (Band XII, XIII and XIV) in TS 25.141

8.2.0

RP-39

RP-080126

0469

1

F

Correction of the node for Band XI BS ACLR

8.2.0

RP-39

RP-080126

0470

F

Correction of spurious emissions limits for coexistence with CDMA850

8.2.0

RP-40

RP-080326

0479

2

F

Correction on emission requirements for protection of public safety operations

8.3.0

RP-41

RP-080632

0480

F

Corrections on the section on BS using antenna array

8.4.0

RP-42

RP-080904

0485

F

Clarification on HS-SCCH structure for Test Model 6

8.5.0

RP-42

RP-080904

0491

3

F

Clarification for test model 1

8.5.0

RP-42

RP-080927

0487

1

F

Clarification of eNB HST propagation conditions (25.141, rel-7)

8.5.0

RP-42

RP-080948

0489

1

B

TS 25.141 modification due to DC HSDPA

8.5.0

RP-42

RP-080945

481

F

Transmitter characteristics Tests for 3G Home NodeB

8.5.0

RP-42

RP-080945

492

1

F

Regional requirement on Home Node B applicability

8.5.0

RP-42

RP-080945

482

F

Receiver characteristics Tests for 3G Home NodeB

8.5.0

RP-42

RP-080945

483

F

Demodulation Requirements Tests for 3G Home NodeB

8.5.0

RP-42

RP-080945

493

F

Modified Test Models for 3G Home NodeB

8.5.0

RP-43

RP-090197

496

F

Co-existence requirement for the band 1880MHz

8.6.0

RP-43

RP-090192

494

F

Change reference bandwidth for ACLR limit for Home BS

8.6.0

RP-43

RP-090192

495

F

3G Home NodeB Transmit Power Conformance Testing for Adjacent Channel Protection

8.6.0

RP-44

RP-090553

499

F

Correction of local area base station coexistence spurious emission requirements

8.7.0

RP-44

RP-090605

497

F

Correction on Home BS Output Power Requirements for Adjacent Channel Protection

8.7.0

RP-44

RP-090605

502

F

Correction on test system uncertainty for Home BS absolute ACLR limit

8.7.0

RP-44

RP-090559

498

B

Introduction of Extended UMTS800 requirements

9.0.0

RP-45

RP-090827

516

1

A

Correction of DPCCH slot format for FRC8

9.1.0

RP-45

RP-090825

505

A

Spectrum emission mask test tolerance correction

9.1.0

RP-45

RP-090825

509

A

Correction of Receiver additional spurious emission requirement

9.1.0

RP-45

RP-090824

511

F

Editorial correction on 6.5.3.7

9.1.0

RP-46

RP-091286

517

 

B

Introduction of Extended UMTS1500 requirements for TS25.141 (Technically endorsed at RAN 4 52bis in R4-093628)

 9.2.0

RP-46

RP-091276

519

 

A

Testing in case of Rx diversity, Tx diversity and MIMO (Technically endorsed at RAN 4 52bis in R4-093983)

 9.2.0

RP-46

RP-091288

520

 

B

Introduction of the BS requirements for DC-HSUPA (Technically Endorsed in R4-52, R4-093331)

 9.2.0

RP-46

RP-091289

521

 

B

Introduction of BS requirements for DB-DC-HSDPA (Technically Endorsed in R4-52, R4-093416)

 9.2.0

RP-46

RP-091277

523

 

A

Corrections on additional spectrum emission limits for Bands XII, XIII, XIV

 9.2.0

RP-46

RP-091296

524

1

F

Correction to the transmitter intermodulation

 9.2.0

RP-46

RP-091296

527

1

A

Time alignment error definition correction for DC-HSDPA

 9.2.0

RP-46

RP-091268

529

1

A

Protection of E-UTRA for UTRA BS

 9.2.0

RP-47

RP-100261

537

A

Corrections on Home BS Output Power Conformance Testing

9.3.0

RP-47

RP-100261

539

1

A

TS 25.141 Removal of testing for receiver diversity port

9.3.0

RP-47

RP-100272

535

1

F

Clarification of time alignment error requirements

9.3.0

RP-47

RP-100263

540

1

B

Introduction of Band XX in 25.141

9.3.0

RP-47

RP-100264

534

F

Corrections for Extended UMTS1500 requirements

9.3.0

RP-47

RP-100267

542

B

Tx-Rx frequency separation for DC-HSUPA

9.3.0

RP-48

RP-100625

548

F

Clarification of applicability of requirements for multi-carrier BS

9.4.0

RP-48

RP-100626

543

F

Correction of blocking performance requirement when co-located with BS in other bands (Band 20)

9.4.0

RP-48

RP-100631

549

F

Correction of RACH message demodulation requirement definitions

9.4.0

RP-48

RP-100631

547

1

F

Co-existence with services in adjacent frequency bands

9.4.0

RP-49

RP-100918

551

A

Corrections on Home BS spurious emission limits for co-existence with Home BS operating in other bands

9.5.0

RP-49

RP-100918

553

A

Clarifications on Base Station transmit and receive configurations

9.5.0

RP-50

RP-101334

566

1

A

Band XII channel arrangement correction on 25.141

9.6.0

RP-50

RP-101340

561

1

F

Revision of Time Alignment Error requirement testing

9.6.0

RP-50

RP-101353

563

 

B

Introduction of frequency bands for 4C-HSDPA

10.0.0

RP-50

RP-101353

562

1

B

Revision of Time Alignment Error requirement testing

10.0.0

RP-50

RP-101361

558

 

B

Protection of E-UTRA Band 24

10.0.0

RP-51

RP-110355

0564

2

B

DB-DC-HSDPA: New band combinations

10.1.0

RP-51

RP-110341

0573

A

Clarification of ambiguity in Test Model 5

10.1.0

RP-51

RP-110352

0576

1

F

Correction of the test port description for TS 25.141 Rel-10

10.1.0

RP-51

RP-110352

0577

1

F

UTRA BS Receiver spurious requirements for protection of other bands

10.1.0

RP-51

RP-110352

0578

1

F

Harmonization of co-existence/co-location requirements between 25.141 and 36.141

10.1.0

RP-52

RP-110788

583

 

A

Modifications to Band 3 to allow LTE Band 3 operation in Japan (Rel-10 TS25.141 CR)

10.2.0

RP-52

RP-110804

584

 

B

Add coexistence requirements for expanded 1900MHz band in 25.141

10.2.0

RP-52

RP-110813

585

 

B

Add 2GHz S-Band (Band 23) in 25.141

10.2.0

RP-52

RP-110800

586

 

B

Definition of Virtual Antenna Mapping (VAM) and applicability of S-CPICH power accuracy requirement

10.2.0

RP-53

RP-111255

592

 

B

Add Band 42 and 43 for LTE 3500 (TDD) to TS 25.141

10.3.0

RP-53

RP-111255

593

1

B

Add Band 22/XXII for LTE/UMTS 3500 (FDD) to TS 25.141

10.3.0

RP-53

RP-111262

588

 

F

Co-existence requirements on TS 25.141

10.3.0

RP-53

RP-111268

587

1

B

Updating BS Coexistence table for Band 23 in 25.141

10.3.0

RP-53

RP-111270

594

1

B

Introduction of S-CPICH power offset accuracy test

10.3.0

RP-54

RP-111686

595

 

F

Removal of TBD in the S-CPICH power offset test

10.4.0

RP-54

RP-111734

596

 

F

Band 42 and 43 for LTE 3500 (TDD) correction to TS 25.141

10.4.0

RP-54

RP-111686

597

 

F

Introduction of HS-DPCCH demodulation performance testing for 4C-HSDPA

10.4.0

RP-54

RP-111734

598

 

F

Clarification of general blocking requirements for co-existence in TS 25.141

10.4.0

RP-54

RP-111687

600

3

F

TX ON or OFF CR 25.141

10.4.0

RP-54

RP-111696

599

1

B

Introduction of new configuration for 4C-HSDPA

11.0.0

RP-55

RP-120305

605

 

B

Introduction of Band 26/XXVI to TS 25. 141

11.1.0

RP-55

RP-120301

606

 

B

MC DB HSDPA: Introduction of configurations I-2-VIII-2 and II-1-V-2 in TS 25.141

11.1.0

RP-55

RP-120297

607

 

A

Correction of frequency range for spurious emission requirements

11.1.0

RP-55

RP-120339

0608

 

A

Addition of Band 23 HeNB specifications in 25.141

11.1.0

RP-56

RP-120787

0609

B

Introduction of non-contiguous operation for 4C-HSDPA

11.2.0

RP-56

RP-120786

0610

1

B

8C-HSDPA: Introduction of BS conformance testing for 8C-HSDPA operation

11.2.0

RP-56

RP-120783

0612

1

A

Update to Regional Requirements table 25.141 – CR Not implemented as the content is not from this spec but from 25.104

 

RP-56

RP-120771

0616

A

Introduction of Japanese Regulatory Requirements to W-CDMA Band VIII (R11)

11.2.0

RP-56

RP-120793

0619

B

Introduction of Band 28

11.2.0

RP-56

RP-120793

0620

B

Introduction of Band 44

11.2.0

RP-56

RP-120792

0621

2

B

Introduction of E850_LB (Band 27) to TS 25.141

11.2.0

RP-56

RP-120766

0625

A

Correction of PHS protection requirements for TS 25.141

11.2.0

RP-57

RP-121314

626

 

F

Alignment of NC-4C-HSDPA configurations table

11.3.0

RP-57

RP-121316

627

1

F

Update of co-location spurious emission in TS 25.141

11.3.0

RP-57

RP-121300

631

 

A

Modificaitions of frequency ranges on spurious emission requirements for Band 6, 18, 19

11.3.0

RP-57

RP-121301

634

 

A

Band VIII ACLR

11.3.0

RP-57

RP-121312

636

 

A

BS test uncertainties above 3 GHz

11.3.0

RP-58

RP-121848

0640

A

Introducing the additional frequency bands of 5 MHz x 2 in 1.7 GHz in Japan to Band III

11.4.0

RP-58

RP-121909

0641

F

Correct f_offsetmax definition for a BS operating in non-contiguous spectrum in TS 25.141

11.4.0

RP-58

RP-121902

0642

B

Introduction of Band 29

11.4.0

RP-60

RP-130768

643

B

Introduction of dual-band 4C-HSDPA configuration for Band I and VIII

11.5.0

RP-60

RP-130764

645

A

2X2MIMO: BS conformance testing for S-CPICH

11.5.0

RP-60

RP-130768

646

F

Correction to Definitions list

11.5.0

RP-60

RP-130800

647

1

B

Indication of HSDPA Multiflow BS performance requirements

11.5.0

RP-60

RP-130792

648

1

B

Introduction of Band 30

12.0.0

RP-60

RP-130790

649

1

B

Introduction of LTE 450 into TS 25.141

12.0.0

RP-61

RP-131293

655

A

Correction on TX-RX sepration for TS25.141

12.1.0

RP-61

RP-131283

656

F

Co-location requirements for E-UTRA Medium Range BS

12.1.0

RP-61

RP-131293

658

A

Correction on Base station maximum output power for TS25.141

12.1.0

RP-61

RP-131287

661

A

Introduction of MIMO mode with 4 transmit antennas

12.1.0

RP-61

RP-131288

662

A

Introduction of BS demodulation performance requirements for HSUPA MIMO

12.1.0

RP-62

RP-131967

667

1

F

Alignment of Note related to BS Spurious emissions limits for co-location with another BS

12.2.0

RP-62

RP-131929

670

1

A

Correction of the terminology used for MIMO mode with two transmit antennas

12.2.0

RP-62

RP-131930

672

 

A

Clarification for CACLR in TS25.141

12.2.0

RP-63

RP-140368

675

 

A

Correction on tested frequency range

12.3.0

RP-64

RP-140926

683

1

B

Introduction of operating band XXXII In TS25.141

12.4.0

RP-65

RP-141562

695

A

CR for RTWP tests (Rel-12)

12.5.0

RP-65

RP-141562

696

F

Update of definitions to support supplemental DL in TS25.141

12.5.0

RP-66

RP-142145

704

 

A

Absolute ACLR limit for UTRA

12.6.0

RP-66

RP-142149

707

 

A

Introduction of multi-carrier multi-band BS testing in TS 25.141 – clauses 1-5

This CR removes several sevtion (by mistake). This change does not appear in the Cat-F CR. This change was thus not implemented.

12.6.0

RP-66

RP-142149

708

 

A

Introduction of multi-carrier and multi-band BS testing in TS 25.141 – clauses 6-7

12.6.0

RP-69

RP-151476

728

A

BS Spec improvements: TS 25.141 Corrections

12.7.0

RP-69

RP-151476

734

A

Multi-band high PSD test configuration clarification

12.7.0

RP-69

RP-151492

726

1

B

CR with updates due to introduction of Rel-13 Multiflow enhancements

13.0.0

RP-70

RP-152141

735

1

B

Introduction of DB-DC-HSUPA for TS25.141

13.1.0

RP-70

RP-152132

741

A

Tx IM requirement correction

13.1.0

RP-70

RP-152157

742

B

Introduction of E-UTRA Band 67 co-existence requirements

13.1.0

RP-70

RP-152172

743

B

Introduction of Band 66

13.1.0

RP-70

RP-152171

744

B

Introduction of Band 65

13.1.0

RP-70

RP-152173

745

B

Introduction of 1447-1467MHz Band into 25.141

13.1.0

RP-70

RP-152132

748

A

BS Spec improvements: TS 25.141 Corrections

13.1.0

RP-70

RP-152132

751

A

Corrections on definition of f_offsetmax for BS operating in multiple bands or non-contiguous spectrum

13.1.0

RP-70

RP-152132

757

A

Correction of UEM requirement for multi-band base station

13.1.0

RP-70

RP-152132

760

A

Clarification on the transmitter intermodulation requirement in TS 25.141

13.1.0

03/2016

RP-71

RP-160483

0761

 

B

Introduction of Band 68

13.2.0

06/2016

RP-72

RP-161134

766

B

Introduction of Band 46 in TS 25.141

13.3.0

06/2016

RP-72

RP-161141

770

A

Corrections to sub-clause number of BS spurious emissions limits in TS25.141 (Rel-13)

13.3.0

06/2016

RP-72

RP-161140

771

F

Corrections on definition of multi-band definition and blocking

13.3.0

2016/06

RP-72

RP-161125

768

B

Introduction of Band 66 to 25.141

14.0.0

2016/06

RP-72

RP-161124

772

B

Introduction of Band 69 co-existence requirements

14.0.0

2016/12

RP-74

RP-162405

0773

B

Introduction of Band 48

14.1.0

2017/06

RP-76

RP-171255

0785

B

CR on eLAA BS for TS 25.141

14.2.0

2017/06

RP-76

RP-171282

0979

1

F

CR on BS for protection of V2X UE in TS 25.141

14.2.0

2017/09

RP-77

RP-171940

0987

F

CR to 25.141: Correction of B70 frequency ranges and unit of measure

14.3.0

2017/09

RP-77

RP-171948

0981

2

B

Introduction of the FDD L-band (Band 74) into TS 25.141

15.0.0

2017/09

RP-77

RP-171946

0982

B

CR to 25.141: Introduction of Band 72

15.0.0

2017/09

RP-77

RP-171950

0983

B

CR to 25.141: Introduction of Band 75 and 76

15.0.0

2017/09

RP-77

RP-171952

0984

B

CR to 25.141: Introduction of Band 71

15.0.0

2017/09

RP-77

RP-171949

0989

1

B

Introduction of TDD L-band into TS 25.141

15.0.0

2017/12

RP-78

RP-172593

0990

B

Introduction of Band 73 into TS 25.141

15.1.0

2017/12

RP-78

RP-172594

0991

1

B

CR to 25.141: Introduction of Band 49

15.1.0

2018-03

RAN#79

RP-180279

0992

B

CR to 25.141: Introduction of Band 85

15.2.0

2018-03

RAN#79

RP-180278

0993

B

Introduction of TDD 3.3-3.4GHz band (band 52)

15.2.0

2018-06

RAN#80

RP-181100

0994

1

F

CR for 25.141: Clarification on spectrum emission mask

15.3.0

2018-12

RAN#82

RP-182388

0996

3

B

Addition of LTE B35 B36 B37 to out of band co-existence & co-location requirements with further change in 25.141

15.4.0

2018-12

RAN#82

RP-182388

0998

F

Addition of LTE B35 B36 B37 to out of band co-existence & co-location requirements with further change in 25.141

15.4.0

2018-12

RAN#82

RP-182376

0997

B

CR to 25.141: Introduction of Band 53

16.0.0

Change history

Date

Meeting

TDoc

CR

Rev

Cat

Subject/Comment

New version

2022-03

SA#95

Update to Rel-17 version (MCC)

17.0.0