6.2B.4 Configured Output Power for EN-DC

38.521-33GPPNRPart 3: Range 1 and Range 2 Interworking operation with other radiosRadio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification

Tools: ARFCN - Frequency Conversion for 5G NR/LTE/UMTS/GSM

6.2B.4.1 Configured Output Power Level for EN-DC

6.2B.4.1.0 Minimum Conformance Requirements

6.2B.4.1.0.1 Configured output power level

6.2B.4.1.0.1.1 Intra-band contiguous EN-DC

The following requirements apply for one component carrier per CG configured for synchronous DC.

For intra-band dual connectivity with one uplink serving cell per CG on E-UTRA and NR respectively, the UE is allowed to set its configured maximum output power P_CMAX,_c(i),ifor serving cell c(i) of CG i, i = 1,2, and its total configured maximum transmission power for EN-DC operation = 10log10() with as specified in clause 7.6 of TS 38.213 [19].

The configured maximum output power P_{CMAX_E-UTRA,}_c(p) in sub-frame p for the configured E-UTRA uplink carrier shall be set within the bounds:

P_{CMAX_L_E-UTRA,}_c (p) ≤ P_{CMAX_E-UTRA,}_c(p) ≤ P_CMAX _{H_E-UTRA,}_c (p)

where P_{CMAX_L_E-UTRA,}_c andP_CMAX _{H_E-UTRA,}_c are the limits for a serving cell c as specified in TS 36.101 [5] clause 6.2.5 modified by P_LTE as follows:

P_{CMAX_L_E-UTRA,}_c = MIN {MIN(P_EMAX,_c, P_{EMAX, EN-DC}, P_LTE) – t_{C_E-UTRA,}c, (P_{PowerClass,EN-DC} – ΔP_{PowerClass,EN-DC}), (P_PowerClass – ΔP_PowerClass) – MAX(MPR_c + A-MPR_c + ΔT_IB,c + T_{C_E-UTRA,}c + T_ProSe, P-MPR_c)}

P_CMAX _{H_E-UTRA,}_c = MIN {P_EMAX,_c, P_{EMAX, EN-DC} , P_LTE, P_{PowerClass, EN-DC}, P_PowerClass – ΔP_PowerClass}

where

– P_EMAX,EN-DC is the value given by the field p-maxUE-FR1 of the RRCConnectionReconfiguration-v1530 IE as defined in TS 36.331 [17];

– P_LTE is the value given by the field p-maxEUTRA-r15 of the RRCConnectionReconfiguration-v1510 IE as defined in TS 36.331 [17] which is the same as P_LTE in TS 38.213 [19];

– ∆t_{C_EUTRA, c} = 1.5 dB when NOTE 2 in Table 6.2.2-1 of TS 36.101 [5] applies; ∆t_{C_EUTRA, c} = 0 dB otherwise;

and whenever NS_01 is not indicated within CG 1:

– for a UE indicating support of dynamicPowerSharing, the MPR_c and the A-MPR_c are determined in accordance with the DCI of serving cell c of the CG 1 and the specification in clause 6.2.4 of TS 36.101 [5];

– for a UE not indicating support of dynamicPowerSharing, the A-MPR_c is determined in accordance with clause 6.2B.3.1 with parameters applicable for UEs not indicating support of dynamicPowerSharing and MPR_c = 0 dB;

and whenever NS_01 is indicated in CG 1:

– for a UE indicating support of dynamicPowerSharing, the MPR_c is determined in accordance with the DCI of serving cell c of the CG 1 and the specification in clause 6.2.4 of TS 36.101 [5];

– for a UE not indicating support of dynamicPowerSharing, the MPR_c is determined in accordance with clause 6.2B.2.1 with parameters applicable for UEs not indicating support of dynamicPowerSharing and A-MPR_c = 0 dB;

The configured maximum output power P_{CMAX_NR,}_c(q) in physical channel q for the configured NR carrier shall be set within the bounds:

P_{CMAX_L,f,}_c,,NR (q) ≤ P_CMAX,f,_c,NR(q) ≤ P_{CMAX_H,f,}_c,NR (q)

where P_{CMAX_L_NR,}_c andP_CMAX _{H_NR,}_c are the limits for a serving cell c as specified in clause 6.2.4 of TS 38.101-1 [2] modified as follows:

P_{CMAX_L,f,}_c,,NR = MIN {MIN(P_EMAX,c , P_{EMAX, EN-DC}, P_NR) – T_{C_NR,}_c, (P_{PowerClass, EN-DC} – ΔP_{PowerClass,EN-DC} ), (P_PowerClass – ΔP_PowerClass) – MAX(MAX(MPR_c, A-MPR_c)+ ΔT_IB,c + T_{C_NR,}_c + ∆T_RxSRS, P-MPR_c) }

P_{CMAX_H,f,}_c,NR = MIN {P_EMAX,c, P_{EMAX, EN-DC}, P_NR , P_{PowerClass, EN-DC}, P_PowerClass – ΔP_PowerClass }

where

– P_EMAX,EN-DC is the value given by the field p-maxUE-FR1 of the RRCConnectionReconfiguration-v1530 IE as defined in TS 36.331 [17];

– P_LTE signalled by RRC as p-MaxEUTRA-r15 in TS 36.331 [17]

– P_NR is the value given by the field p-NR-FR1 of the PhysicalCellGroupConfig IE as defined in [18] and signalled by RRC;

– ΔT_{c_E-UTRA,}_c = 1.5dB when NOTE 2 in Table 6.2.2-1 in TS 36.101 [4] applies for a serving cell c, otherwise T_{C_E-UTRA,}_c = 0dB;

– T_{C_NR,}_c = 1.5dB when NOTE 3 in Table 6.2.1-1 in TS 38.101-1 [2] applies for a serving cell c, otherwise T_{C_NR,}_c = 0dB;

– ΔT_IB,c specified in clause 6.2B.4.2.1 for EN-DC, the individual Power Class defined in table 6.2B.1.1 and any other additional power reductions parameters specified in clauses 6.2B.2 and 6.2B.3 for EN-DC are applicable to P_{CMAX_}_E-UTRA,_cand P_CMAX,f,_c,NRevaluations.

P_{PowerClass, EN-DC} is defined in clause 6.2B.1.1 for intra-band contiguous EN-DC;

– P_{PowerClass,NR} is the nominal UE power of the power class that the UE supports for the NR band of the EN-DC combination as defined in clause 6.2.1 of 38.101-1 [2]; in case IE [powerClassNRPart] as defined in TS 38.331 [18] is indicated, P_{PowerClass,NR} should use that value instead.

– P_{PowerClass,E-UTRA} is the nominal UE power of the power class that the UE supports for the E-UTRA band of the EN-DC combination as defined in clause 6.2.2 of 36.101 [5];-

ΔP_{PowerClass,EN-DC}is 3 dB for a power class 2 capable EN-DC UE when LTE UL/DL configuration is 0 or 6; or LTE UL/DL configuration is 1 and special subframe configuration is 0 or 5; ΔP_{PowerClass,EN-DC}= 3 dB when the IE p-maxUE-FR1 as defined in TS 36.331 [17] is provided and set to the maximum output power of the default power class or lower; ΔP_{PowerClass,EN-DC}is 6 dB for a power class 1.5 capable EN-DC UE when the LTE UL duty cycle is greater than max(50%, maxUplinkDutyCycle); ΔP_{PowerClass,EN-DC}is 3 dB for a power class 1.5 capable EN-DC UE when the LTE UL duty cycle is between max(50%, maxUplinkDutyCycle) and max(25%, maxUplinkDutyCycle/2); otherwise ΔP_{PowerClass,EN-DC}= 0 dB;

and whenever NS_01 is not indicated within CG 2:

– for a UE indicating support of dynamicPowerSharing, A-MPR_c = A-MPR’_c with A-MPR’_c determined in accordance with clause 6.2B.3.1 and MPR_c = 0 dB if transmission(s) in subframe p on CG 1 overlap in time with physical channel q on CG 2;

– for a UE indicating support of dynamicPowerSharing, A-MPR_c is determined in accordance with TS 38.101-1 [2] if transmission(s) in subframe p on CG 1 does not overlap in time with physical channel q on CG 2;

and whenever NS_01 is indicated in CG 2.

– for a UE indicating support of dynamicPowerSharing, MPRc = MPR’c with MPR’c determined in accordance with clause 6.2B.2.1 and A-MPRc = 0 dB if transmission(s) in subframe p on CG 1 overlap in time with physical channel q on CG 2;

– for a UE indicating support of dynamicPowerSharing, MPRc is determined in accordance with TS 38.101-1 [2] if transmission(s) in subframe p on CG 1 does not overlap in time with physical channel q on CG 2;

– for a UE not indicating support of dynamicPowerSharing, the MPRc is determined in accordance with clause 6.2B.2.1 with parameters applicable for UEs not indicating support of dynamicPowerSharing and A‑MPRc = 0 dB;

If the transmissions from NR and E-UTRA do not overlap, then the complete clauses for configured transmitted power for E-UTRA and NR respectively from their own specifications apply with the modifications specified above. The lower value between P_{PowerClass, EN-DC} or P_{EMAX, EN-DC} shall not be exceeded at any time by UE.

If the EN-DC UE is not supporting dynamic power sharing, then the complete clauses for configured transmitted power for E-UTRA and NR respectively from their own specifications TS 36.101 [5] and TS 38.101-1 [2] respectively apply with the modifications specified above.

If the UE does not support dynamic power sharing,

= MIN { P_{EMAX, EN-DC} , P_{PowerClass, EN-DC} – ΔP_{PowerClass,EN-DC} } + 0.3 dB

For UEs indicating support of dynamicPowerSharing in the UE-MRDC-Capability IE the UE can configure the total maximum transmission power within the range

P_{EN-DC,tot_L} ≤ ≤ P_{EN-DC,tot_H}

where

P_{EN-DC,tot_L}(p,q) = MIN{ P_{PowerClass,EN-DC} – ΔP_{PowerClass,EN-DC} – MAX{MPR_tot, A-MPR_tot}, P_EMAX,EN-DC}

P_{EN-DC,tot_H}(p,q) = MIN{P_{PowerClass,EN-DC}, P_EMAX,EN-DC}

for sub-frame p on CG 1 overlapping with physical channel q on CG 2 and with MPR_tot and A-MPR_tot in accordance with 6.2B.2.1 and clause 6.2B.3.1, respectively.

The measured total maximum output power P_UMAX over both CGs/RATs, measured over the transmission reference time duration is

P_UMAX = 10 log₁₀ [p_UMAX,_c,E-UTRA + p_UMAX,_f,c,NR],

where p_UMAX,_c,E-UTRA and p_UMAX,_c,NR denotes the measured output power of serving cell c for E-UTRA and NR respectively, expressed in linear scale.

For UEs indicating support of dynamicPowerSharing, the measured total configured maximum output power P_UMAX shall be within the following bounds:

P_{CMAX_L} -T_LOW (P_{CMAX_L}) ≤ P_UMAX ≤ P_{CMAX_H} + T_HIGH (P_{CMAX_H})

with the tolerances T_LOW(P_{CMAX_L}) and T_HIGH(P_{CMAX_H}) for applicable values of P_{CMAX_L} and P_{CMAX_L} specified in Table 6.2B.4.1.0.1.1-2.

When an UL subframe transmission p from E-UTRA overlap with a physical channel q from the NR, then for P_UMAX evaluation, the E-UTRA subframe p is taken as reference period T_REF and always considered as the reference measurement duration and the following rules are applicable.

T_REF and T_eval are specified in Table 6.2B.4.1.0.1.1-1 when same or different subframes and physical channel durations are used in aggregated carriers. P_{PowerClass ,EN-DC} shall not be exceeded by the UE during any evaluation period of time.

Table 6.2B.4.1.0.1.1-1: P_CMAX evaluation window

transmission duration	T_REF	T_eval
Different transmission duration in different RAT carriers	E-UTRA Subframe	Min(T_{no_hopping}, Physical Channel Length)

For each T_REF, the P_{CMAX_H} is evaluated per T_eval and given by the maximum value over the transmission(s) within the T_eval as follows:

P_{CMAX_H}= MAX { P_{CMAX_EN-DC_H} (p,q) , P_{CMAX_EN-DC_H} (p,q+1), … , P_{CMAX_EN-DC_H} (p,q+n) }

where P_{CMAX_EN-DC_H} are the applicable upper limits for each overlapping scheduling unit pairs (p,q) , (p, q+1) , up to (p, q+n) for each applicable T_eval duration, where q+n is the last NR UL physical channel overlapping with LTE subframe p.

While P_{CMAX_L}is computed as follows:

P_{CMAX_L}= MIN { P_{CMAX_EN-DC_L} (p,q) , P_{CMAX_EN-DC_L} (p,q+1), … , P_{CMAX_EN-DC_L} (p,q+n)}

where P_{CMAX_EN-DC_L} are the applicable lower limits for each overlapping scheduling unit pairs (p,q) , (p, q+1) , up to (p, q+n) for each applicable T_eval duration, where q+n is the last NR UL physical channel overlapping with E-UTRA subframe p,

With

P_{CMAX_EN-DC_H}(p,q) = MIN {10 log₁₀ [p_CMAX _{H_E-UTRA,}_c(p) + p_CMAX _H,f,_c,NR _c(q)], P_{EMAX, EN-DC} ,P_{PowerClass, EN-DC}}

And:

a= 10 log₁₀ [p_{CMAX_E-UTRA,}_c(p) +p_CMAX,f,_c,NR(q) ] > P_{EN-DC,tot_L}

b= 10 log₁₀ [p_{CMAX_E-UTRA,}_c(p) +p_CMAX,f,_c,NR(q) /X_scale] > P_{EN-DC,tot_L}

If a= FALSE and the configured transmission power spectral density between the MCG and SCG differs by less than 6 dB

P_{CMAX_EN-DC_L}(p,q) = MIN {10 log₁₀ [p_CMAX _{L_E-UTRA,}_c(p) + p_CMAX _L,f,_c,,NR _c(q)], P_{EMAX, EN-DC} ,P_{PowerClass, EN-DC}– ΔP_{PowerClass,EN-DC} }

ELSE If (a=TRUE) AND (b=FALSE) and the configured transmission power spectral density between the MCG and SCG differs by less than 6 dB

P_{CMAX_EN-DC_L}(p,q) = MIN {10 log₁₀ [p_CMAX _{L_E-UTRA,}_c(p) + p_CMAX _L,f,_c,,NR _c(q) /X_scale ], P_{EMAX, EN-DC} ,P_{PowerClass, EN-DC}– ΔP_{PowerClass,EN-DC} }

ELSE If b= TRUE or the transmission power after power scaling spectral density between the MCG and SCG differs by more than 6 dB

P_{CMAX_EN-DC_L}(p,q) = MIN {10 log₁₀ [p_CMAX _{L_E-UTRA,}_c(p) ], P_{EMAX, EN-DC} ,P_{PowerClass, EN-DC}– ΔP_{PowerClass,EN-DC} }

where

– p_CMAX _{H_E-UTRA,}_c(p) is the E-UTRA higher limit of the maximum configured power expressed in linear scale;

– p_CMAX _{H_NR,}_c(q) is the NR higher limit of the maximum configured power expressed in linear scale;

– p_CMAX _{L_E-UTRA,}_c(p) is the E-UTRA lower limit of the maximum configured power expressed in linear scale;

– p_CMAX _{L_NR,}_c(q) is the NR lower limit of the maximum configured power expressed in linear scale;

– P_{PowerClass, EN-DC} is defined in clause 6.2B.1.1.3-1 for intra-band EN-DC;

– X_scale is the linear value of X dB which is configured by RRC and can only take values [0 , 6] dB

– p_{CMAX E-UTRA,c}(p) is the linear value of P_{CMAX E-UTRA,c}(p), the real configured max power for E-UTRA

– p_CMAX,f,c_NR(q) is the linear value of P_CMAX,f,c_NR(q), the real configured max power of NR

Table 6.2B.4.1.0.1.1-2: P_CMAX tolerance for Dual Connectivity E-UTRANR

P_CMAX(dBm)	Tolerance T_LOW(P_{CMAX_L}) (dB)	Tolerance T_HIGH (P_{CMAX_H}) (dB)
23 ≤ P_CMAX≤ 33	3.0	2.0
22 ≤ P_CMAX< 23	5.0	2.0
21 ≤ P_CMAX< 22	5.0	3.0
20 ≤ P_CMAX < 21	6.0	4.0
16 ≤ P_CMAX < 20	5.0
11 ≤ P_CMAX < 16	6.0
-40 ≤ P_CMAX < 11	7.0

If the UE supports dynamic power sharing, and when LTE and NR transmissions overlap and the condition (If (a=TRUE) AND (b=FALSE)) is met, SCG shall be transmitted and the following supplementary minimum requirement apply for the measured SCG power, P_UMAX,f,_c,NR(q), under nominal conditions and unless otherwise stated.

10log(p_CMAX _L,f,_c,,NR(q)/X_scale) – T_LOW (10log(p_CMAX _L,f,_c,,NR(q)/X_scale) )} ≤ P_UMAX,f,_c,NR(q) ≤ 10log(p_CMAX _{H, f,}_c,,NR (q)) + T_HIGH (10log(p_CMAX _{H, f,}_c,,NR (q))).

with the tolerances T_LOWand T_HIGHfor applicable values of P_CMAX specified in Table 6.2B.4.1.0.1.1-2.

If the UE supports dynamic power sharing, the measured maximum output power in subframe p on CG 1, p_UMAX,_c,E-UTRA, shall meet the requirements in clause 6.2.5 in TS 36.101 [5] with the limits P_{CMAX_L,}_c and P_{CMAX_H,}_c replaced by P_{CMAX_L_E-UTRA,}_c and P_{CMAX_H_E- UTRA,}_c as specified above, respectively.

If the configured transmission power spectral density between the MCG and SCG differs by more than 6 dB, then

P_UMAX,f,_c,NR(q) ≤ 10log(p_CMAX _{H, f,}_c,,NR (q)) + T_HIGH (10log(p_CMAX _{H, f,}_c,NR (q))).

6.2B.4.1.0.1.2 Intra-band non-contiguous EN-DC

The following requirements apply for one component carrier per CG configured for synchronous DC. The CG(s) are indexed by j = 1 for MCG and j = 2 for SCG.

The configured maximum output power P_{CMAX_E-UTRA,}_c(p) in sub-frame p for the configured E-UTRA uplink carrier shall be set in accordance with clause 6.2B.4.1.0.1.1 but where

– for a UE not indicating support of dynamicPowerSharing, the A-MPR_c determined in accordance with clause 6.2B.3.2 with parameters applicable for UEs not indicating support of dynamicPowerSharing and MPR_c = 0 dB;

whenever NS_01 is not indicated within CG 1 while

– for a UE not indicating support of dynamicPowerSharing, the MPR_c determined in accordance with clause 6.2B.2.2 with parameters applicable for UEs not indicating support of dynamicPowerSharing and A-MPR_c = 0 dB;

whenever NS_01 is indicated in CG 1.

The configured maximum output power P_{CMAX_NR,}_c(q) in physical channel q for the configured NR carrier shall be set in accordance with clause 6.2B.4.1.0.1.1 but where

– for a UE indicating support of dynamicPowerSharing, A-MPR_c = A-MPR’_c with A-MPR’_c determined in accordance with clause 6.2B.3.2 and MPR_c = 0 dB if transmission(s) in subframe p on CG 1 overlap in time with physical channel q on CG 2;

– for a UE indicating support of dynamicPowerSharing, A-MPR_c is determined in accordance with [2] if transmission(s) in subframe p on CG 1 does not overlap in time with physical channel q on CG 2;

– for a UE not indicating support of dynamicPowerSharing, the A-MPR_c is determined in accordance with clause 6.2B.3.2 with parameters applicable for UEs not indicating support of dynamicPowerSharing and MPR_c = 0 dB;

For UEs indicating support of dynamicPowerSharing in the UE-MRDC-Capability IE, the UE can configure the total transmission power in accordance with clause 6.2B.4.1.0.1.1 but with P_{powerclass,EN-DC}the EN-DC power class of the intra-band non-contiguous band combination configured and A-MPR determined in accordance with clause 6.2B.3.2.

whenever NS_01 is not indicated in CG 2 while

– for a UE indicating support of dynamicPowerSharing, MPR_c = MPR’_c with MPR’_c determined in accordance with clause 6.2B.2.2 and A-MPR_c = 0 dB if transmission(s) in subframe p on CG 1 overlap in time with physical channel q on CG 2;

– for a UE indicating support of dynamicPowerSharing, MPR_c is determined in accordance with TS 38.101-1 [2] if transmission(s) in subframe p on CG 1 does not overlap in time with physical channel q on CG 2;

– for a UE not indicating support of dynamicPowerSharing, the MPR_c is determined in accordance with clause 6.2B.2.2 with parameters applicable for UEs not indicating support of dynamicPowerSharing and A-MPR_c = 0 dB;

whenever NS_01 is indicated in CG 2.

For UEs indicating support of dynamicPowerSharing in the UE-MRDC-Capability IE, the UE can configure the total transmission power in accordance with clause 6.2B.4.1.1 but with P_{powerclass,EN-DC}the EN-DC power class of the intra-band non-contiguous band combination configured and A-MPR determined in accordance with clause 6.2B.3.2.

The total maximum output power P_UMAX over both CGs is measured in accordance with clause 6.2B.4.1.0.1.1 and shall be within the limits specified in clause 6.2B.4.1.0.1.1 but with parameters applicable for the non-contiguous band combination configured.

The maximum output power levels p_UMAX,_c,E-UTRA and p_UMAX,_f,c,NR for the CGs are measured in accordance with clause 6.2B.4.1.0.1.1 and shall be within the limits specified in clause 6.2B.4.1.0.1.1 but with parameters applicable for the non-contiguous band combination configured.

6.2B.4.1.0.1.3 Inter-band EN-DC within FR1

For inter-band dual connectivity with one uplink serving cell or more than one uplink serving cells configured for intra-band UL CA on the E-UTRA CG and one uplink serving cell on the NR CG or more than one uplink serving cells configured for intra-band UL CA, the UE is allowed to set its configured maximum output power P_CMAX,_c(i),ifor serving cell c(i) of CG i, i = 1,2, and its total configured maximum transmission power for EN-DC operation, = 10log10() with as specified in clause 7.6 of TS 38.213 [19]. For EN-DC with more than one uplink serving cells configured for intra-band UL CA on the E-UTRA CG, the P_CMAXapplies to the entire E-UTRA CG.

For a UE configured with EN-DC and serving cell frame structure type 1, if the UE is configured with subframeAssignment-r15 for the serving cell and E-UTRA Pcell is FDD, the UE is not expected to be configured with more than one serving cells in the uplink.

The configured maximum output power P_{CMAX_E-UTRA,}_c(p) in sub-frame p for the configured E-UTRA uplink carrier shall be set within the bounds:

P_{CMAX_L_E-UTRA,}_c (p) ≤ P_{CMAX_E-UTRA,}_c(p) ≤ P_CMAX _{H_E-UTRA,}_c (p)

where P_{CMAX_L_E-UTRA,}_c andP_CMAX _{H_E-UTRA,}_c are the limits for a serving cell c as specified in TS 36.101 [5] clause 6.2.5 modified by P_LTE as follows:

P_{CMAX_L_E-UTRA,}_c = MIN { P_{EMAX, EN-DC} , (P_{PowerClass, EN-DC}– ΔP_{PowerClass, EN-DC} ), MIN(P_EMAX,_c, P_LTE) – t_{C_E-UTRA,}_c, (P_{PowerClass,E-UTRA} – ΔP_{PowerClass,E-UTRA}) – MAX(MPR_c + A-MPR_c + ΔT_IB,c + t_{C _E-UTRA,}_c + T_ProSe, P-MPR_c)}

P_CMAX _{H_E-UTRA,}_c = MIN {P_EMAX,_c, P_{EMAX, EN-DC} , (P_{PowerClass, EN-DC}– ΔP_{PowerClass, EN-DC} ), P_LTE, P_{PowerClass, E-UTRA} – ΔP_{PowerClass, E-UTRA}}

For EN-DC with more than one uplink serving cells configured for intra-band UL CA on the E-UTRA CG, P_{CMAX_L_}_E-UTRA,_c andP_CMAX _{H _}_E-UTRA,_c are the limits for the E-UTRA CG as specified in TS 36.101 [5] clause 6.2.5A modified by P_LTE as follows:

P_{CMAX_L_}_E-UTRA,_c = MIN{10 log₁₀ ∑ p_EMAX,c – T_C, (P_{PowerClass,E-UTRA} – ΔP_{PowerClass,E-UTRA}) – MAX(MPR + A-MPR + ΔT_IB,c + T_C + T_ProSe, P-MPR), P_LTE, P_{PowerClass,EN-DC}}

P_CMAX _{H _}_E-UTRA,_c = MIN{10 log₁₀ ∑ p_EMAX,c, P_{PowerClass,E-UTRA}, P_LTE, P_{PowerClass,EN-DC}}

The configured maximum output power P_{CMAX_NR,}_c(q) in physical-channel q for the configured NR carrier shall be set within the bounds:

P_{CMAX_L,f,}_c,,NR (q) ≤ P_CMAX,f,_c,NR(q) ≤ P_{CMAX_H,f,}_c,NR (q)

where P_{CMAX_L_NR,}_c andP_CMAX _{H_NR,}_c are the limits for a serving cell c as specified in clause 6.2.4 of TS 38.101-1 [2] modified as follows:

P_{CMAX_L,f,}_c,,NR = MIN { P_{EMAX, EN-DC} , (P_{PowerClass, EN-DC}– ΔP_{PowerClass, EN-DC} ), MIN(P_EMAX,c , P_NR ) – T_{C_NR,}_c, (P_{PowerClass, NR} – ΔP_{PowerClass, NR}) – MAX(MAX(MPR_c, A-MPR_c)+ ΔT_IB,c + T_{C_NR,}_c + ∆T_RxSRS, P-MPR_c) }

P_{CMAX_H,f,}_c,NR = MIN {P_EMAX,c, P_{EMAX, EN-DC} , (P_{PowerClass, EN-DC}– ΔP_PowerClass ), P_NR , P_{PowerClass, NR} – ΔP_{PowerClass, NR} }

where

– P_EMAX,EN-DC is the value given by the field p-maxUE-FR1 of the RRCConnectionReconfiguration-v1530 IE as defined in TS 36.331 [17];

– If more than one E-UTRA uplink serving cell is configured as intra-band UL CA in the E-UTRA CG, P_PowerClass refers to the maximum output power of the E-UTRA intra-band CA power class given in Table 6.2.2A-1 of TS 36.101 [5];

– P_LTE is the value given by the field p-maxEUTRA-r15 of the RRCConnectionReconfiguration-v1510 IE as defined in TS 36.331 [17];

– If more than one E-UTRA uplink serving cell is configured as intra-band UL CA in the E-UTRA CG, MPR_c = MPR and A-MPR_c = A-MPR with MPR and A-MPR specified in clause 6.2.3A and clause 6.2.4A of TS 36.101 [5] respectively. There is one power management term for the UE, denoted P-MPR, and P-MPR_c = P-MPR. P_{CMAX_}_E-UTRA,_c is calculated under the assumption that the transmit power is increased by the same amount in dB on all component carriers within the E-UTRA CG.

– P_NR is the value given by the field p-NR-FR1 of the PhysicalCellGroupConfig IE as defined TS 38.331 [18];

– Δt_{c_E-UTRA,}_c = 1.5 dB when NOTE 2 in Table 6.2.2-1 in TS 36.101 [5] applies for a serving cell c, otherwise T_{C_E-UTRA,}_c = 0 dB;

– T_{C_NR,}_c = 1.5dB when NOTE 3 in Table 6.2.1-1 in TS 38.101-1 [2] applies for a serving cell c, otherwise T_{C_NR,}_c = 0 dB;

– ΔT_IB,c specified in clause 6.2B.4.2.3 for EN-DC, the individual Power Class defined in table 6.2B.1.3 and any other additional power reductions parameters specified in clauses 6.2B.2 and 6.2B.3for EN-DC are applicable to P_{CMAX_}_E-UTRA,_cand P_CMAX,f,_c,NRevaluations.

– P_{PowerClass, EN-DC} is defined in clause 6.2B.1.3 for inter-band EN-DC;

– P_{PowerClass,E-UTRA} is the nominal UE power of the power class that the UE supports for the E-UTRA band of the EN-DC combination as defined in clause 6.2.2 of 36.101 [5];

– ∆P_{PowerClass,EN-DC} = 3 dB for a power class 2 capable EN-DC UE when requirements of default power class had been applied as specified in sub-clause 6.2B.1; otherwise ∆P_{PowerClass,EN-DC} = 0 dB;

= 10log10() with the configured maximum transmission power for EN-DC operation as specified in clause 7.6 of TS 38.213 [19].

The total configured maximum transmission power for both synchronous and non-synchronous operation is

= MIN { P_{EMAX, EN-DC} ,P_{PowerClass, EN-DC}– ΔP_PowerClass }

If the UE does not support dynamic power sharing,

= MIN { P_{EMAX, EN-DC} ,P_{PowerClass, EN-DC}– ΔP_{PowerClass, EN-DC}} + 0.3 dB

If the EN-DC UE does not support dynamic power sharing, then the complete clauses for configured transmitted power for E-UTRA and NR respectively from their own specifications TS 36.101 [5] and TS 38.101-1 [2] respectively apply with the modifications specified above and applies.

When a UE supporting dynamic sharing is configured for overlapping E-UTRA uplink and NR uplink transmissions, the UE can set its configured maximum output power P_{CMAX_E-UTRA,}_cand P_{CMAX_NR,}_cfor the configured E-UTRA and NR uplink carriers, respectively, and its configured maximum transmission power for EN-DC operation, , as specified above.

The measured total maximum output power P_UMAX over both CGs/RATs, measured over the transmission reference time duration is

P_UMAX = 10 log₁₀ [p_UMAX,_c,E-UTRA + p_UMAX,_c,NR],

where p_UMAX,_c,E-UTRA and p_UMAX,_c,NR denotes the measured output power of serving cell c for E-UTRA and NR respectively, expressed in linear scale.

The measured total configured maximum output power P_UMAX shall be within the following bounds:

P_{CMAX_L} -T_LOW (P_{CMAX_L}) ≤ P_UMAX ≤ P_{CMAX_H} + T_HIGH (P_{CMAX_H})

with the tolerances T_LOW(P_{CMAX_H}) and T_HIGH(P_{CMAX_H}) for applicable values of P_CMAX specified in Table 6.2B.4.1.0.1.3-2.

When an UL subframe transmission p from E-UTRA overlap with a physical-channel q from the NR, then for P_UMAX evaluation, the E-UTRA subframe p is taken as reference period T_REF and always considered as the reference measurement duration and the following rules are applicable.

T_REF and T_eval are specified in Table 6.2B.4.1.0.1.3-1 when same or different subframe and physical-channel durations are used in aggregated carriers. P_{PowerClass ,EN-DC} shall not be exceeded by the UE during any evaluation period of time.

Table 6.2B.4.1.0.1.3-1: P_CMAX evaluation window

transmission duration	T_REF	T_eval
Different transmission duration in different RAT carriers	E-UTRA Subframe on all aggregated cells of E-UTRA	Min(T_{no_hopping}, Physical Channel Length)

For each T_REF, the P_{CMAX_H} is evaluated per T_eval and given by the maximum value over the transmission(s) within the T_eval as follows:

P_{CMAX_H}= MAX { P_{CMAX_EN-DC_H} (p,q) , P_{CMAX_EN-DC_H} (p,q+1), … , P_{CMAX_EN-DC_H} (p,q+n) }

While P_{CMAX_L}is computed as follows:

P_{CMAX_L}= MIN { P_{CMAX_EN-DC_L} (p,q) , P_{CMAX_EN-DC_L} (p,q+1), … , P_{CMAX_EN-DC_L} (p,q+n)}

With

P_{CMAX_EN-DC_H}(p,q) = MIN {10 log₁₀ [p_CMAX _{H_E-UTRA,}_c(p) + p_CMAX _H,f,_c,NR _c(q)], P_{EMAX, EN-DC} ,P_{PowerClass, EN-DC}}

And:

a= 10 log₁₀ [p_{CMAX_E-UTRA,}_c(p) +p_CMAX,f,_c,NR(q) ] >

b= 10 log₁₀ [p_{CMAX_E-UTRA,}_c(p) +p_CMAX,f,_c,NR(q) /X_scale] >

If a= FALSE

P_{CMAX_EN-DC_L}(p,q) = MIN {10 log₁₀ [p_CMAX _{L_E-UTRA,}_c(p) + p_CMAX _L,f,_c,,NR _c(q)], P_{EMAX, EN-DC} ,P_{PowerClass, EN-DC}}

ELSE If (a=TRUE) AND (b=FALSE)

P_{CMAX_EN-DC_L}(p,q) = MIN {10 log₁₀ [p_CMAX _{L_E-UTRA,}_c(p) + p_CMAX _L,f,_c,,NR _c(q) /X_scale ], P_{EMAX, EN-DC} ,P_{PowerClass, EN-DC}}

ELSE If b= TRUE

P_{CMAX_EN-DC_L}(p,q) = MIN {10 log₁₀ [p_CMAX _{L_E-UTRA,}_c(p) ], P_{EMAX, EN-DC} ,P_{PowerClass, EN-DC}}

where

– p_CMAX _{H_E-UTRA,}_c(p) is the E-UTRA higher limit of the maximum configured power expressed in linear scale;

– p_CMAX _{H_NR,}_c(q) is the NR higher limit of the maximum configured power expressed in linear scale;

– p_CMAX _{L_E-UTRA,}_c(p) is the E-UTRA lower limit of the maximum configured power expressed in linear scale;

– p_CMAX _{L_NR,}_c(q) is the NR lower limit of the maximum configured power expressed in linear scale;

– P_{PowerClass, EN-DC} is defined in clause 6.2B.1.3-1 for inter-band EN-DC;

– X_scale is the linear value of X dB which is configured by RRC and can only take values [0 , 6]

– p_{CMAX_E-UTRA,c}(p) is the linear value of P_{CMAX_E-UTRA,c}(p), the configured max power for E-UTRA. If more than one E-UTRA uplink serving cell is configured as intra-band UL CA in the E-UTRA CG, P_{CMAX_ E-UTRA,c}(p) will be replaced by P_CMAX(p) which is the configured maximum power for the entire E-UTRA CG.

– p_CMAX,f,c,NR(q) is the linear value of P_CMAX,f,c,NR (q), the real configured max power of NR

Table 6.2B.4.1.0.1.3-2: P_CMAX tolerance for Dual Connectivity E-UTRA-NR

P_CMAX(dBm)	Tolerance T_LOW(P_{CMAX_L}) (dB)	Tolerance T_HIGH (P_{CMAX_H}) (dB)
23 ≤ P_CMAX≤ 33	3.0	2.0
22 ≤ P_CMAX< 23	5.0	2.0
21 ≤ P_CMAX< 22	5.0	3.0
20 ≤ P_CMAX < 21	6.0	4.0
16 ≤ P_CMAX < 20	5.0
11 ≤ P_CMAX < 16	6.0
-40 ≤ P_CMAX < 11	7.0
NOTE 1: For UEs not indicating support of dynamic power sharing, the upper tolerance T_high shall be reduced by 0.3 dB for P ≥ 20 dBm.

When E-UTRA and NR transmissions overlap and the condition (If (a=TRUE) AND (b=FALSE)) is met, SCG shall be transmitted and the following supplementary minimum requirement apply for the measured SCG power, P_UMAX,f,_c,NR(q), under nominal conditions.

10log(p_CMAX _L,f,_c,,NR _c(q)/X_scale) – T_LOW (10log(p_CMAX _L,f,_c,,NR _c(q)/X_scale) )} ≤ P_UMAX,f,_c,NR(q) ≤ 10log(p_CMAX _{H, f,}_c,,NR _c (q)) + T_HIGH (10log(p_CMAX _{H, f,}_c,,NR _c (q))).

with the tolerances T_LOWand T_HIGHfor applicable values of P_CMAX specified in Table 6.2B.4.1.0.1.3-2.

6.2B.4.1.0.1.4 Inter-band EN-DC including FR2

For inter-band dual connectivity with one uplink serving cell per CG on E-UTRA and NR respectively, with NR configured in FR2, the UE is allowed to set its configured maximum output power P_CMAX,c(i),i for serving cell c(i) of CG i, i = 1,2.

The UE maximum configured power P_CMAX,c(i), on E-UTRA for the subframe i shall be set according to clause 6.2.5 from TS 36.101 [5]. Applicable inter-band ΔT_IB,c parameters shall be used according to the clauses 6.2B.4.2.4 or 6.2B.4.2.5.

The UE maximum configured power P_CMAX,c(j), on NR for the slot j shall be set according to clause 6.2.4 from TS 38.101-2 [3].

For the configured power measurements TS 36.101 [5] clause 6.2.5 and TS 38.101-2 [3] clause 6.2.4 are applicable.

6.2B.4.1.0.1.5 Inter-band EN-DC including both FR1 and FR2

For inter-band dual connectivity with one uplink serving cell per CG on E-UTRA and NR respectively, with both CGs configured in FR1, the requirements specified in clause 6.2B.4.1.0.1.3 apply.

For inter-band dual connectivity with one uplink serving cell per CG on E-UTRA and NR respectively, with NR configured in FR2, the requirements specified in clause 6.2B.4.1.0.1.4 apply.

For inter-band dual connectivity with one uplink serving cell in first CG on E-UTRA and two uplink serving cells in second CG on NR FR1 and NR FR2 respectively, the UE is allowed to set its configured maximum output power P_CMAX,c(i),i for serving cell c(i) , i = 1,2,3 with i=1 for E-UTRA, i=2 for NR FR1 and i=3 for NR FR2.

– For serving cell on FR2, the requirements specified in clause 6.2.4 in TS 38.101-2 [3] apply to the UE maximum configured power P_CMAX,c(3),3 and the measured maximum configured power.

– For remaining inter-band dual connectivity involving CG1 and CG2, the requirements specified in clause 6.2B.4.1.0.1.3 apply.

6.2B.4.1.1 Configured Output Power Level for Intra-Band Contiguous EN-DC

6.2B.4.1.1.1 Test purpose

To verify the UE does not exceed the power bounds defined by P_{CMAX_L} and P_{CMAX_H}

6.2B.4.1.1.2 Test applicability

This test case applies to all types of E-UTRA UE release 15 and forward, supporting intra-band contiguous EN-DC.

6.2B.4.1.1.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.2B.4.1.0.1.1.

Exception requirements for both NR and E-UTRA are defined for this test and therefore LTE anchor agnostic approach is not applied. E-UTRA test point analysis is included and E-UTRA measurements are performed.

6.2B.4.1.1.4 Test description

6.2B.4.1.1.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies and channel bandwidths based on EN-DC operating bands specified in clause 5.3B.1.2, channel bandwidths and sub-carrier spacings for the NR cell specified in TS 38.521-1 [8] clause 5.3 and channel bandwidth for the E-UTRA cell are specified in TS 36.521-1 [10] clause 5.4.2. All of these configurations shall be tested with applicable test parameters for each EN-DC configuration specified in clause 5.3B.1.2 and are shown in table 6.2B.4.1.1.4.1-1. The details of the uplink reference measurement channels (RMCs) are specified in Annex A.2. Configurations of PDSCH and PDCCH before measurement are specified in TS 36.521-1 [10] Annex C.2 and in TS 38.521-1 [8] Annex C.2 for E-UTRA CG and NR CG respectively.

Table 6.2B.4.1.1.4.1-1: Test configurations table for intra-band contiguous EN-DC

Initial Conditions
Test Environment as specified in TS 38.508-1 [5] clause 4.1			Normal, TL/VL, TL/VH, TH/VL, TH/VH
NR and E-UTRA Test Frequencies as specified in TS 38.508-1 [5] clause 4.3.1			Mid range
Test EN-DC bandwidth combination as specified in TS 38.508-1 [5] clause 4.3.1			Lowest N_{RB_agg}, Highest N_{RB_agg}
NR Test SCS as specified in Table 5.3.5-1 in TS 38.521-1 [8]			Highest
NR/E-UTRA Test Parameters for UE supporting DPS
Test ID (NOTE 3)	Downlink Configuration	EN-DC Uplink Configuration
		E-UTRA Cell			NR Cell
		Modulation	RB allocation (NOTE 2)	P_LTE	Modulation	RB allocation (NOTE 1)	P_NR
1a-1f	N/A	QPSK	Full_Allocation	{-13, 7, 12, 15, 19, 23} for PC3 UE {-13, 7, 12, 15, 21, 26} for PC2 UE	CP-OFDM QPSK	Outer_Full	{-13, 7, 12, 15, 18, 23} for PC3 UE {-13, 7, 12, 15, 21, 26} for PC2 UE
2a-2c		QPSK	Partial_Allocation	{-10, 10, 15}	N/A	N/A	{-10, 10, 15}
3a-3c		N/A	N/A	{-10, 10, 15}	DFT-s-OFDM QPSK	Inner Full	{-10, 10, 15}
NR/E-UTRA Test Parameters for UE not supporting DPS
Test ID (NOTE 3)	Downlink Configuration	EN-DC Uplink Configuration
		E-UTRA Cell			NR Cell
		Modulation	RB allocation (NOTE 2)	P_LTE	Modulation	RB allocation (NOTE 1)	P_NR
1a-1d	N/A	QPSK	Full_Allocation	{-10, 10, 15, 23} for PC3 UE {-10, 10, 15, 26} for PC2 UE	CP-OFDM QPSK	Outer_Full	{-10, 10, 15, 23} for PC3 UE {-10, 10, 15, 26} for PC2 UE
2a-2c		QPSK	Partial_Allocation	{-10, 10, 15}	N/A	N/A	{-10, 10, 15}
3a-3c		N/A	N/A	{-10, 10, 15}	DFT-s-OFDM QPSK	Inner Full	{-10, 10, 15}
NOTE 1: The specific configuration of each RB allocation is defined in Table 6.1-1 in TS 38.521-1 [8]. NOTE 2: The specific configuration of each RB allocation is defined in Table 6.1-1 in current specification. NOTE 3: The suffix in Test ID identifies the configured power level being tested from the P_LTE and P_NR lists

Table 6.2B.4.1.1.4.1-2: Void

1. Connect the SS to the UE antenna connectors as shown in [6] TS 38.508-1 A.3.1.2.1 for SS diagram and A.3.2.1 for UE diagram.

2. The parameter settings for the E-UTRA cell are set up according to TS 36.508 [11] clause 4.4.3, and the parameter settings for the NR cell are set up according to TS 38.508-1 [6] clause 4.4.3.

3. Downlink signals are initially set up according to TS 36.521-1 [10] Annex C.0 and TS 38.521-1 [8] Annex C.0 for E-UTRA CG and NR CG respectively, and uplink signals according to TS 36.521-1 [10] Annex H and TS 38.521-1 [8] Annex G for E-UTRA CG and NR CG respectively.

4. The UL Reference Measurement channels are TS 36.521-1 [10] Annex A.2 and TS 38.521-1 [8] Annex A.2 for E-UTRA CG and NR CG respectively.

5. Propagation conditions are set according to TS 36.521-1 [10] Annex B.0 and TS 38.521-1 [8] Annex B.0 for E-UTRA CG and NR CG respectively.

6. Ensure the UE is in state RRC_CONNECTED with generic procedure parameters Connectivity EN-DC, DC bearer MCG and SCG, Connected without release On according to TS 38.508-1 [6] clause 4.5. Message contents are defined in clause 6.2B.4.1.1.4.3.

7. For the case of testing overlapping E-UTRA and NR UL transmission scenario when both bands are TDD, ensure E-UTRA UL transmission overlaps with NR UL transmission in time by giving SCG a delay of 3 E-UTRA subframes, or by giving MCG a delay of 2 subframes.

6.2B.4.1.1.4.2 Test procedure

1. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 and DCI format 0_1 for C_RNTI to schedule the UL RMC according table 6.2B.4.1.1.4.1-1 on E-UTRA CC and NR CC respectively. For test points configured with message in Table 6.2B.4.1.1.4.3-1, NR SS only schedules UL RMC on NR slots that does not overlap with E-UTRA uplink subframe. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

2. Send continuously uplink power control "up" commands to the UE for NR and E-UTRA carrier until the UE transmits at its P_UMAX level; allow at least 200 ms from the first TPC command for the UE to reach P_UMAX level.

3. Measure the mean transmitted power over E-UTRA component carrier and NR component carrier respectively, or/and measure the sum of mean transmitted power over E-UTRA and NR component carriers according to Table 6.2B.4.1.1.5-1 and Table 6.2B.4.1.1.5-2. The period of the measurement shall be at least the continuous duration of one active sub-frame. For TDD, only slots consisting of only UL symbols are under test.

NOTE 1: When switching to DFT-s-OFDM waveform, as specified in the test configuration Table 6.2B.4.1.1.4.1-1, send an NR RRCReconfiguration message according to TS 38.508-1 [6] clause 4.6.3 Table 4.6.3-118 PUSCH-Config with TRANSFORM_PRECODER_ENABLED condition.

6.2B.4.1.1.4.3 Message contents

Message contents are according to TS 36.508 [11] clause 4.6.1 and TS 38.508-1 [6] clause 4.6.1 with the following exceptions.

Table 6.2B.4.1.1.4.3-1: RRCConnectionReconfiguration: tdm-PatternConfig if E-UTRA on FDD band and UE doesn’t support dynamic power sharing

Derivation Path: TS 36.508 [11], Table 4.6.1-8
Information Element		Value/remark	Comment	Condition
tdm-PatternConfig-r15 CHOICE{			Test ID 1d
setup SEQUENCE {
subframeAssignment-r15	sa2
harq-Offset-r15	0
}
}

Table 6.2B.4.1.1.4.3-2: SystemInfomationBlockType1: tdd-Config if E-UTRA on TDD band

Derivation Path: TS 36.508 [11], Table 4.6.3-23
Information Element	Value/remark	Comment	Condition
TDD-Config-DEFAULT ::= SEQUENCE {		Operating on TDD band
subframeAssignment	sa2
specialSubframePatterns	ssp7
}

Table 6.2B.4.1.1.4.3-3: RRCConnectionReconfiguration: nr-Config-r15

Derivation Path: TS 36.508 [11], Table 4.6.1-8
Information Element		Value/remark	Comment	Condition
p-MaxEUTRA-r15	Defined as P_LTE in Table 6.2B.4.1.1.4.1-1

Table 6.2B.4.1.1.4.3-4: PhysicalCellGroupConfig

Derivation Path: TS 38.508-1 [6], Table 4.6.3-106
Information Element	Value/remark	Comment	Condition
PhysicalCellGroupConfig ::= SEQUENCE {
p-NR-FR1	Defined as P_NR in Table 6.2B.4.1.1.4.1-1
}

Table 6.2B.4.1.1.4.3-5: RRCConnectionReconfiguration: p-MaxUE-FR1-r15

Derivation Path: TS 36.508 [11], Table 4.6.1-8
Information Element	Value/remark	Comment	Condition
nonCriticalExtension SEQUENCE {		RRCConnectionReconfiguration-v1530-IEs
p-MaxUE-FR1-r15	23		Power Class 3 UE
	26		Power Class 2 UE
}

6.2B.4.1.1.5 Test requirement

For UE supporting DPS, the output power measured shall not exceed the values specified in Table 6.2B.4.1.1.5-1.

Table 6.2B.4.1.1.5-1: P_CMAX configured UE output power for UE supporting DPS

	E-UTRA component carrier	NR component carrier	Total power measured over E-UTRA and NR component carriers
Test ID 1a	Not measured	Not measured	-10dBm ± (7+TT)
Test ID 1b	Not measured	Not measured	10dBm ± (7+TT)
Test ID 1c	Not measured	Not measured	15 ± (6+TT)
Test ID 1d	Not measured	Not measured	18 ± (5+TT)
Test ID 1e	Not measured	18 + (5+TT) / 11 – (6+TT) for PC3 UE	21.54dBm + (3+TT) / 19.64 – (5+TT) for PC3 UE
		21 + (3+TT) / 14 – (6+TT) for PC2 UE (Rel-15 UE indicates PC2 on NR band, Rel-16 and forward UE repoting (PC2 by P_{PowerClass,NR}, and PC2 or Not present by powerClassNRPart-r16))	24 + (2+TT) / 21.8 – (5+TT) for PC2 UE (Rel-15 UE indicates PC2 on NR band, Rel-16 and forward UE reporting (PC2 by P_{PowerClass,NR}, and PC2 or Not present by powerClassNRPart-r16))
		21 + (3+TT) / 11 – (6+TT) for PC2 UE (Rel-15 and forward UE indicates PC3 on NR band, Rel-16 and forward UE reporting (PC2 by P_{PowerClass,NR}, and PC3 by powerClassNRPart-r16))	24 + (2+TT) / 21.4 – (5+TT) for PC2 UE (Rel-15 and forward UE indicates PC3 on NR band, Rel-16 and forward UE reporting (PC2 by P_{PowerClass,NR}, and PC3 by powerClassNRPart-r16))
Test ID 1f	Maximum output power with reduction as defined in Table 6.2.3.5-1 of TS 36.521-1 [10] for PC3 UE	N/A	Maximum output power with reduction as defined in Table 6.2.3.5-1 of TS 36.521-1 [10] for PC3 UE
	Maximum output power with reduction as defined in Table 6.2.3_1.5-1 of TS 36.521-1 [10] for PC2 UE		Maximum output power with reduction as defined in Table 6.2.3_1.5-1of TS 36.521-1 [10] for PC2 UE
Test ID 2a	-10dBm ± (7+TT)	N/A-	Not measured
Test ID 2b	10dBm ± (6+TT)	N/A-	Not measured
Test ID 2c	15dBm ± (5+TT)	N/A-	Not measured
Test ID 3a	N/A	-10dBm ± (7+TT)	Not measured
Test ID 3b	N/A	10dBm ± (6+TT)	Not measured
Test ID 3c	N/A	15dBm ± (5+TT)	Not measured
NOTE 1: In addition NOTE 2 in Table 6.2.2-1 in TS 36.101 [5] and/or NOTE 3 in Table 6.2.1-1 in TS 38.101-1 [2] shall apply to the tolerances. NOTE 2: TT for each frequency and channel bandwidth is specified in Table 6.2B.4.1.1.5-3

For UE not supporting DPS, the output power measured shall not exceed the values specified in Table 6.2B.4.1.1.5-2.

Table 6.2B.4.1.1.5-2: P_CMAX configured UE output power for UE not supporting DPS

	E-UTRA component carrier	NR component carrier	Total power measured over E-UTRA and NR component carriers
Test ID 1a	-10 dBm ± (7+TT)	-10 dBm ± (7+TT)	Not measured
Test ID 1b	10 dBm ± (6+TT)	10 dBm ± (6+TT)	Not measured
Test ID 1c	15 dBm ± (5+TT)	15 dBm ± (5+TT)	Not measured
Test ID 1d	Maximum output power with reduction as defined in Table 6.2.3.5-1 of TS 36.521-1 [10] for PC3 UE	N/A	Not measured
	Maximum output power with reduction as defined in Table 6.2.3_1.5-1 of TS 36.521-1 [10] for PC2 UE
Test ID 2a	-10dBm ± (7+TT)	N/A	Not measured
Test ID 2b	10dBm ± (6+TT)	N/A	Not measured
Test ID 2c	15dBm ± (5+TT)	N/A	Not measured
Test ID 3a	N/A	-10dBm ± (7+TT)	Not measured
Test ID 3b	N/A	10dBm ± (6+TT)	Not measured
Test ID 3c	N/A	15dBm ± (5+TT)	Not measured
NOTE 1: In addition NOTE 2 in Table 6.2.2-1 in TS 36.101 [5] and/or NOTE 3 in Table 6.2.1-1 in TS 38.101-1 [2] shall apply to the tolerances. NOTE 2: TT for each frequency and channel bandwidth is specified in Table 6.2B.4.1.1.5-3

Table 6.2B.4.1.1.5-3: Test Tolerance (UE configured UE output power)

	f ≤ 3.0GHz	3.0GHz < f ≤ 4.2GHz	4.2GHz < f ≤ 6.0GHz
BW ≤ 40MHz	0.7 dB	1.0 dB	1.0 dB
40MHz < BW ≤ 100MHz	1.0 dB	1.0 dB	1.0 dB

6.2B.4.1.2 Configured Output Power for Intra-Band Non-Contiguous EN-DC

6.2B.4.1.2.1 Test purpose

To verify the UE does not exceed the power bounds defined by P_{CMAX_L} and P_{CMAX_H}.

6.2B.4.1.2.2 Test applicability

This test case applies to all types of E-UTRA UE release 15 and forward, supporting intra-band non-contiguous EN-DC.

6.2B.4.1.2.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.2B.4.1.0.1.2.

6.2B.4.1.2.4 Test description

6.2B.4.1.2.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies and channel bandwidths based on EN-DC operating bands specified in clause 5.3B.1.2, channel bandwidths and sub-carrier spacings for the NR cell specified in TS 38.521-1 [8] clause 5.3 and channel bandwidth for the E-UTRA cell are specified in TS 36.521-1 [10] clause 5.4.2. All of these configurations shall be tested with applicable test parameters for each EN-DC configuration specified in clause 5.3B.1.2 and are shown in table 6.2B.4.1.2.4.1-1. The details of the uplink reference measurement channels (RMCs) are specified in Annex A.2. Configurations of PDSCH and PDCCH before measurement are specified in TS 36.521-1 [10] Annex C.2 and in TS 38.521-1 [8] Annex C.2 for E-UTRA CG and NR CG respectively.

Table 6.2B.4.1.2.4.1-1: Test configurations table for intra-band non-contiguous EN-DC

Initial Conditions
Test Environment as specified in TS 38.508-1 [5] clause 4.1			Normal, TL/VL, TL/VH, TH/VL, TH/VH
NR and E-UTRA Test Frequencies as specified in TS 38.508-1 [5] clause 4.3.1			Maximum Wgap
Test EN-DC bandwidth combination as specified in TS 38.508-1 [5] clause 4.3.1			Lowest N_{RB_agg}, Highest N_{RB_agg}
NR Test SCS as specified in Table 5.3.5-1 in TS 38.521-1 [8]			Highest
NR/E-UTRA Test Parameters for UE supporting DPS
Test ID (NOTE 3)	Downlink Configuration	EN-DC Uplink Configuration
		E-UTRA Cell			NR Cell
		Modulation	RB allocation (NOTE 2)	P_LTE	Modulation	RB allocation (NOTE 1)	P_NR
1a-1d	N/A	QPSK	Full_Allocation	{-13, 7, 10, 23} for PC3 UE {-13, 7, 12, 26} for PC2 UE	CP-OFDM QPSK	Outer_Full	{-13, 7, 10, 23} for PC3 UE {-13, 7, 13, 26} for PC2 UE
2a-2c		QPSK	Partial_Allocation	{-10, 10, 15}	N/A	N/A	{-10, 10, 15}
3a-3c		N/A	N/A	{-10, 10, 15}	DFT-s-OFDM QPSK	Inner Full	{-10, 10, 15}
NR/E-UTRA Test Parameters for UE not supporting DPS
Test ID (NOTE 3)	Downlink Configuration	EN-DC Uplink Configuration
		E-UTRA Cell			NR Cell
		Modulation	RB allocation (NOTE 2)	P_LTE	Modulation	RB allocation (NOTE 1)	P_NR
1a-1b	N/A	QPSK	Full_Allocation	{-10, 23} for PC3 UE {-10, 26} for PC2 UE	CP-OFDM QPSK	Outer_Full	{-10, 23} for PC3 UE {-10, 26} for PC2 UE
2a-2c		QPSK	Partial_Allocation	{-10, 10, 15}	N/A	N/A	{-10, 10, 15}
3a-3c		N/A	N/A	{-10, 10, 15}	DFT-s-OFDM QPSK	Inner Full	{-10, 10, 15}
NOTE 1: The specific configuration of each RB allocation is defined in Table 6.1-1 in TS 38.521-1 [8]. NOTE 2: The specific configuration of each RB allocation is defined in Table 6.1-1 in current specification. NOTE 3: The suffix in Test ID identifies the configured power level being tested from the P_LTE and P_NR lists

Table 6.2B.4.1.2.4.1-2: Void

1. Connect the SS to the UE antenna connectors as shown in [6] TS 38.508-1 A.3.1.2.1 for SS diagram and A.3.2.1 for UE diagram.

2. The parameter settings for the E-UTRA cell are set up according to TS 36.508 [11] clause 4.4.3, and the parameter settings for the NR cell are set up according to TS 38.508-1 [6] clause 4.4.3.

4. The UL Reference Measurement channels are TS 36.521-1 [10] Annex A.2 and TS 38.521-1 [8] Annex A.2 for E-UTRA CG and NR CG respectively.

5. Propagation conditions are set according to TS 36.521-1 [10] Annex B.0 and TS 38.521-1 [8] Annex B.0 for E-UTRA CG and NR CG respectively.

6.2B.4.1.2.4.2 Test procedure

1. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 and DCI format 0_1 for C_RNTI to schedule the UL RMC according table 6.2B.4.1.2.4.1-1 on E-UTRA CC and NR CC respectively. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

3. Measure the mean transmitted power over E-UTRA component carrier and NR component carrier respectively, or/and measure the sum of mean transmitted power over E-UTRA and NR component carriers according to Table 6.2B.4.1.2.5-1 and Table 6.2B.4.1.2.5-2. The period of the measurement shall be at least the continuous duration of one active sub-frame. For TDD, only slots consisting of only UL symbols are under test.

NOTE 1: When switching to DFT-s-OFDM waveform, as specified in the test configuration Table 6.2B.4.1.2.4.1-1, send an NR RRCReconfiguration message according to TS 38.508-1 [6] clause 4.6.3 Table 4.6.3-118 PUSCH-Config with TRANSFORM_PRECODER_ENABLED condition.

6.2B.4.1.2.4.3 Message contents

Message contents are according to TS 36.508 [11] clause 4.6.1 and TS 38.508-1 [6] clause 4.6.1 with the following exceptions.

Table 6.2B.4.1.2.4.3-1: RRCConnectionReconfiguration: tdm-PatternConfig if E-UTRA on FDD band and UE doesn’t support dynamic power sharing

Derivation Path: TS 36.508 [11], Table 4.6.1-8
Information Element		Value/remark	Comment	Condition
tdm-PatternConfig-r15 CHOICE{
setup SEQUENCE {
subframeAssignment-r15	sa2
harq-Offset-r15	0
}
}

Table 6.2B.4.1.2.4.3-2: SystemInfomationBlockType1: tdd-Config if E-UTRA on TDD band

Derivation Path: TS 36.508 [11], Table 4.6.3-23
Information Element	Value/remark	Comment	Condition
TDD-Config-DEFAULT ::= SEQUENCE {		Operating on TDD band
subframeAssignment	sa2
specialSubframePatterns	ssp7
}

Table 6.2B.4.1.2.4.3-3: RRCConnectionReconfiguration: nr-Config-r15

Derivation Path: TS 36.508 [11], Table 4.6.1-8
Information Element		Value/remark	Comment	Condition
p-MaxEUTRA-r15	Defined as P_LTE in Table 6.2B.4.1.2.4.1-1

Table 6.2B.4.1.2.4.3-4: PhysicalCellGroupConfig

Derivation Path: TS 38.508-1 [6], Table 4.6.3-106
Information Element	Value/remark	Comment	Condition
PhysicalCellGroupConfig ::= SEQUENCE {
p-NR-FR1	Defined as P_NR in Table 6.2B.4.1.2.4.1-1
}

Table 6.2B.4.1.2.4.3-5: RRCConnectionReconfiguration: p-MaxUE-FR1-r15

Derivation Path: TS 36.508 [11], Table 4.6.1-8
Information Element	Value/remark	Comment	Condition
nonCriticalExtension ::= SEQUENCE {		RRCConnectionReconfiguration-v1530-IEs
p-MaxUE-FR1-r15	23		Power Class 3 UE
	26		Power Class 2 UE
}

6.2B.4.1.2.5 Test requirement

For UE supporting DPS, the output power measured shall not exceed the values specified in Table 6.2B.4.1.2.5-1.

Table 6.2B.4.1.2.5-1: P_CMAX configured UE output power for UE supporting DPS

	E-UTRA component carrier	NR component carrier	Total power measured over E-UTRA and NR component carriers
Test ID 1a	Not measured	Not measured	-10dBm ± (7+TT)
Test ID 1b	Not measured	Not measured	10dBm ± (7+TT)
Test ID 1c	Not measured	10 + (7+TT) / 2 – (7+TT) for PC3 UE	13.0 + (6+TT) / 10.64 – (7+TT) for PC3 UE
		13 + (6+TT) / 5 – (7+TT) for PC2 UE (Rel-15 UE indicates PC2 on NR band, Rel-16 and forward UE reporting (PC2 by P_{PowerClass,NR}, and PC2 or Not present by powerClassNRPart-r16))	15.5 + (6+TT) / 12.8 – (6+TT) for PC2 UE (Rel-15 UE indicates PC2 on NR band, Rel-16 and forward UE reporting (PC2 by P_{PowerClass,NR}, and PC2 or Not present by powerClassNRPart-r16))
		13 + (6+TT) / 2 – (7+TT) for PC2 UE (Rel-15 and forward UE indicates PC3 on NR band, Rel-16 and forward UE reporting (PC2 by P_{PowerClass,NR}, and PC3 by powerClassNRPart-r16))	15.5 + (6+TT) / 12.4 – (6+TT) for PC2 UE (Rel-15 and forward UE indicates PC3 on NR band, Rel-16 and forward UE reporting (PC2 by P_{PowerClass,NR}, and PC3 by powerClassNRPart-r16))
Test ID 1d	Maximum output power with reduction as defined in Table 6.2.3.5-1 of TS 36.521-1 [10] for PC3 UE	N/A	Maximum output power with reduction as defined in Table 6.2.3.5-1 of TS 36.521-1 [10] for PC3 UE
	Maximum output power with reduction as defined in Table 6.2.3_1.5-1 of TS 36.521-1 [10] for PC2 UE		Maximum output power with reduction as defined in Table 6.2.3_1.5-1 of TS 36.521-1 [10] for PC2 UE
Test ID 2a	-10dBm ± (7+TT)	N/A	Not measured
Test ID 2b	10dBm ± (6+TT)	N/A	Not measured
Test ID 2c	15dBm ± (5+TT)	N/A	Not measured
Test ID 3a	N/A	-10dBm ± (7+TT)	Not measured
Test ID 3b	N/A	10dBm ± (6+TT)	Not measured
Test ID 3c	N/A	15dBm ± (5+TT)	Not measured
NOTE 1: In addition NOTE 2 in Table 6.2.2-1 in TS 36.101 [5] and/or NOTE 3 in Table 6.2.1-1 in TS 38.101-1 [2] shall apply to the tolerances. NOTE 2: TT for each frequency and channel bandwidth is specified in Table 6.2B.4.1.1.5-3

For UE not supporting DPS, the output power measured shall not exceed the values specified in Table 6.2B.4.1.1.5-2.

Table 6.2B.4.1.2.5-2: P_CMAX configured UE output power for UE not supporting DPS

	E-UTRA component carrier	NR component carrier	Total power measured over E-UTRA and NR component carriers
Test ID 1a	-10 dBm ± (7+TT)	-10 dBm ± (7+TT)	Not measured
Test ID 1b	Maximum output power with reduction as defined in Table 6.2.3.5-1 of TS 36.521-1 [10] for PC3 UE	N/A	Not measured
	Maximum output power with reduction as defined in Table 6.2.3_1.5-1 of TS 36.521-1 [10] for PC2 UE
Test ID 2a	-10dBm ± (7+TT)	N/A	Not measured
Test ID 2b	10dBm ± (6+TT)	N/A	Not measured
Test ID 2c	15dBm ± (5+TT)	N/A	Not measured
Test ID 3a	N/A	-10dBm ± (7+TT)	Not measured
Test ID 3b	N/A	10dBm ± (6+TT)	Not measured
Test ID 3c	N/A	15dBm ± (5+TT)	Not measured
NOTE 1: In addition NOTE 2 in Table 6.2.2-1 in TS 36.101 [5] and/or NOTE 3 in Table 6.2.1-1 in TS 38.101-1 [2] shall apply to the tolerances. NOTE 2: TT for each frequency and channel bandwidth is specified in Table 6.2B.4.1.1.5-3

Table 6.2B.4.1.2.5-3: Test Tolerance for UE configured UE output power (Separate measurements over E-UTRA and NR CCs)

Uplink TX		f ≤ 3.0GHz	3.0GHz < f ≤ 4.2GHz	4.2GHz < f ≤ 6GHz
E-UTRA	BW ≤ 20MHz	0.7 dB	1.0 dB	1.3 dB
NR	BW ≤ 40MHz	0.7 dB	1.0 dB	1.0 dB
NR	40MHz < BW ≤ 100MHz	1.0 dB	1.0 dB	1.0 dB

Table 6.2B.4.1.2.5-4: Test Tolerance for UE configured UE output power (Combined measurements of E-UTRA and NR CCs)

TT for overall output power
			NR
			BW ≤ 20MHz			20 MHz < BW ≤ 40MHz			40MHz < BW ≤ 100MHz
			f ≤ 3.0GHz	3.0GHz < f ≤ 4.2GHz	4.2GHz < f ≤ 6.0GHz	f ≤ 3.0GHz	3.0GHz < f ≤ 4.2GHz	4.2GHz < f ≤ 6.0GHz	f ≤ 3.0GHz	3.0GHz < f ≤ 4.2GHz	4.2GHz < f ≤ 6.0GHz
E-UTRA	BW ≤ 20MHz	f ≤ 3.0GHz	0.7 dB	1.0 dB	1.0 dB	0.7 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB
E-UTRA	BW ≤ 20MHz	3.0GHz < f ≤ 4.2GHz	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB

6.2B.4.1.3 Configured Output Power for Inter-Band EN-DC within FR1 (1 E-UTRA CC, 1 NR CC)

6.2B.4.1.3.1 Test purpose

To verify the UE does not exceed the power bounds defined by P_CMAX and P_{CMAX_H.}

6.2B.4.1.3.2 Test applicability

This test case applies to all types of E-UTRA UE release 15 and forward, supporting inter-band EN-DC with 1 E-UTRA CC and 1 NR CC within FR1.

6.2B.4.1.3.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.2B.4.1.0.1.3.

6.2B.4.1.3.4 Test description

6.2B.4.1.3.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies and channel bandwidths based on EN-DC operating bands specified in clause 5.3B.1.2, channel bandwidths and sub-carrier spacings for the NR cell specified in TS 38.521-1 [8] clause 5.3 and channel bandwidth for the E-UTRA cell are specified in TS 36.521-1 [10] clause 5.4.2. All of these configurations shall be tested with applicable test parameters for each EN-DC configuration specified in clause 5.3B.1.2 and are shown in table 6.2B.4.1.3.4.1-1. The details of the uplink reference measurement channels (RMCs) are specified in Annex A.2. Configurations of PDSCH and PDCCH before measurement are specified in TS 36.521-1 [10] Annex C.2 and in TS 38.521-1 [8] Annex C.2 for E-UTRA CG and NR CG respectively.

Table 6.2B.4.1.3.4.1-1: Test configurations table for inter-band EN-DC

Initial Conditions
Test Environment as specified in TS 38.508-1 [5] clause 4.1			Normal, TL/VL, TL/VH, TH/VL, TH/VH
NR Test Frequencies as specified in TS 38.508-1 [5] clause 4.3.1 E-UTRA Test Frequencies as specified in TS 36.508-1 [11] clause 4.3.1			Mid range (NOTE 4)
Test EN-DC bandwidth combination as specified in TS 38.508-1 [5] clause 4.3.1			5MHz for E-UTRA CC1 and Lowest for NR CC1, Highest for E-UTRA CC1 and Highest for NR CC1
NR Test SCS as specified in Table 5.3.5-1 in TS 38.521-1 [8]			Highest
NR/E-UTRA Test Parameters for UE supporting DPS
Test ID (NOTE 3)	Downlink Configuration	EN-DC Uplink Configuration
		E-UTRA Cell			NR Cell
		Modulation	RB allocation (NOTE 2)	P_LTE	Modulation	RB allocation (NOTE 1)	P_NR
1a-1h	N/A	QPSK	Partial_Allocation	{-13, 12, 14, 17, 18, 19, 20, 23} for PC3 UE {-13, 12, 14, 17, 18, 19, 23, 26} for PC2 UE	DFT-s-OFDM QPSK	Inner_Full	{-13, 12, 14, 17, 18, 19, 23, 23} for PC3 UE {-13, 12, 14, 17, 18, 19, 26, 26} for PC2 UE
2a-2c		QPSK	Partial_Allocation	{-10, 10, 15}	N/A	N/A	{-10, 10, 15}
3a-3c		N/A	N/A	{-10, 10, 15}	DFT-s-OFDM QPSK	Inner_Full	{-10, 10, 15}
NR/E-UTRA Test Parameters for UE not supporting DPS
Test ID (NOTE 3)	Downlink Configuration	EN-DC Uplink Configuration
		E-UTRA Cell			NR Cell
		Modulation	RB allocation (NOTE 2)	P_LTE	Modulation	RB allocation (NOTE 1)	P_NR
1a-1d	N/A	QPSK	Partial_Allocation	{-10, 10, 15, 23} for PC3 UE {-10, 10, 15, 26} for PC2 UE	CP-OFDM QPSK	Inner_Full	{-10, 10, 15, 23} for PC3 UE {-10, 10, 15, 26} for PC2 UE
2a-2c		QPSK	Partial_Allocation	{-10, 10, 15}	N/A	N/A	{-10, 10, 15}
3a-3c		N/A	N/A	{-10, 10, 15}	DFT-s-OFDM QPSK	Inner_Full	{-10, 10, 15}
NOTE 1: The specific configuration of each RB allocation is defined in Table 6.1-1 in TS 38.521-1 [8]. NOTE 2: The specific configuration of each RB allocation is defined in Table 6.1-1 in current specification. NOTE 3: The suffix in Test ID identifies the configured power level being tested from the P_LTE and P_NR lists NOTE 4: For NR band n28, 30MHz test channel bandwidth is tested with Low range test frequency.

Table 6.2B.4.1.3.4.1-2: Void

1. Connect the SS to the UE antenna connectors as shown in [6] TS 38.508-1 A.3.1.2.1 for SS diagram and A.3.2.1 for UE diagram.

2. The parameter settings for the E-UTRA cell are set up according to TS 36.508 [11] clause 4.4.3, and the parameter settings for the NR cell are set up according to TS 38.508-1 [6] clause 4.4.3.

4. The UL Reference Measurement channels are TS 36.521-1 [10] Annex A.2 and TS 38.521-1 [8] Annex A.2 for E-UTRA CG and NR CG respectively.

5. Propagation conditions are set according to Table 6.2B.4.1.3.4.1-1.

6.2B.4.1.3.4.2 Test procedure

1. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 and DCI format 0_1 for C_RNTI to schedule the UL RMC according table 6.2B.4.1.3.4.1-1 on E-UTRA CC and NR CC respectively. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

3. Measure the mean transmitted power over E-UTRA component carrier and NR component carrier respectively, or/and measure the sum of mean transmitted power over E-UTRA and NR component carriers according to Table 6.2B.4.1.3.5-1 and Table 6.2B.4.1.3.5-2. The period of the measurement shall be at least the continuous duration of one active sub-frame. For TDD, only slots consisting of only UL symbols are under test. For FDD band in inter-band CA with both TDD band and FDD band, only slots overlapping with only UL symbols in TDD are under test.

NOTE 1: When switching to DFT-s-OFDM waveform, as specified in the test configuration Table 6.2B.4.1.3.4.1-1, send an NR RRCReconfiguration message according to TS 38.508-1 [6] clause 4.6.3 Table 4.6.3-118 PUSCH-Config with TRANSFORM_PRECODER_ENABLED condition.

6.2B.4.1.3.4.3 Message contents

Message contents are according to TS 36.508 [11] clause 4.6.1 and TS 38.508-1 [6] clause 4.6.1 with the following exceptions.

Table 6.2B.4.1.3.4.3-1: RRCConnectionReconfiguration: tdm-PatternConfig if E-UTRA on FDD band and UE doesn’t support dynamic power sharing

Derivation Path: TS 36.508 [11], Table 4.6.1-8
Information Element		Value/remark	Comment	Condition
tdm-PatternConfig-r15 CHOICE{
setup SEQUENCE {
subframeAssignment-r15	sa2
harq-Offset-r15	0
}
}

Table 6.2B.4.1.3.4.3-2: SystemInfomationBlockType1: tdd-Config if E-UTRA on TDD band

Derivation Path: TS 36.508 [11], Table 4.6.3-23
Information Element	Value/remark	Comment	Condition
TDD-Config-DEFAULT ::= SEQUENCE {		Operating on TDD band
subframeAssignment	sa2
specialSubframePatterns	ssp7
}

Table 6.2B.4.1.3.4.3-3: RRCConnectionReconfiguration: nr-Config-r15

Derivation Path: TS 36.508 [11], Table 4.6.1-8
Information Element		Value/remark	Comment	Condition
p-MaxEUTRA-r15	Defined as P_LTE in Table 6.2B.4.1.3.4.1-1

Table 6.2B.4.1.3.4.3-4: PhysicalCellGroupConfig

Derivation Path: TS 38.508-1 [6], Table 4.6.3-106
Information Element	Value/remark	Comment	Condition
PhysicalCellGroupConfig ::= SEQUENCE {
p-NR-FR1	Defined as P_NR in Table 6.2B.4.1.3.4.1-1
}

Table 6.2B.4.1.3.4.3-5: RRCConnectionReconfiguration: p-MaxUE-FR1-r15

Derivation Path: TS 36.508 [11], Table 4.6.1-8
Information Element	Value/remark	Comment	Condition
nonCriticalExtension SEQUENCE {		RRCConnectionReconfiguration-v1530-IEs
p-MaxUE-FR1-r15	23		Power Class 3 UE
	26		Power Class 2 UE
}

6.2B.4.1.3.5 Test requirement

For UE supporting DPS, the output power measured shall not exceed the values specified in Table 6.2B.4.1.3.5-1.

Table 6.2B.4.1.3.5-1: P_CMAX configured UE output power for UE supporting DPS

	E-UTRA component carrier	NR component carrier	Total power measured over E-UTRA and NR component carriers
Test ID 1a	Not measured	Not measured	-10dBm ± (7+TT)
Test ID 1b	Not measured	Not measured	15dBm ± (6+TT)
Test ID 1c	Not measured	Not measured	17 ± (5+TT)
Test ID 1d	Not measured	Not measured	20 + (4+TT)/ – (6+TT)
Test ID 1e	Not measured	Not measured	21 + (3+TT)/ – (5+TT)
Test ID 1f	Not measured	Not measured	22+ (2+TT)/ – (5+TT)
Test ID 1g	Not measured	23 + (2+TT) / 17 – (5+TT) for PC3 UE	23 + (2+TT) / 21.8 – (5+TT) for PC3 UE
		26 + (2+TT) / 20 – (6+TT) for PC2 UE (Rel-15 UE indicates PC2 on NR band, Rel-16 and forward UE reporting (PC2 by P_{PowerClass,NR}, and PC2 or Not present by powerClassNRPart-r16))	26 + (2+TT) / 24.8 – (3+TT) for PC2 UE (Rel-15 UE indicates PC2 on NR band, Rel-16 and forward UE reporting (PC2 by P_{PowerClass,NR}, and PC2 or Not present by powerClassNRPart-r16))
		23 + (2+TT) / 17 – (5+TT) for PC2 UE (Rel-15 and forward UE indicates PC3 on NR band, Rel-16 and forward UE reporting (PC2 by P_{PowerClass,NR}, and PC3 by powerClassNRPart-r16))	26 + (2+TT) / 24.0 – (3+TT) for PC2 UE (Rel-15 and forward UE indicates PC3 on NR band, Rel-16 and forward UE reporting (PC2 by P_{PowerClass,NR}, and PC3 by powerClassNRPart-r16))
Test ID 1h	Maximum output power with reduction as defined in Table 6.2.3.5-1 of TS 36.521-1 [10] for PC3 UE	N/A	Maximum output power with reduction as defined in Table 6.2.3.5-1 of TS 36.521-1 [10] for PC3 UE
	Maximum output power with reduction as defined in Table 6.2.3_1.5-1 of TS 36.521-1 [10] for PC2 UE		Maximum output power with reduction as defined in Table 6.2.3_1.5-1 of TS 36.521-1 [10] for PC2 UE
Test ID 2a	-10dBm ± (7+TT)	N/A	Not measured
Test ID 2b	10dBm ± (6+TT)	N/A	Not measured
Test ID 2c	15dBm ± (5+TT)	N/A	Not measured
Test ID 3a	N/A	-10dBm ± (7+TT)	Not measured
Test ID 3b	N/A	10dBm ± (6+TT)	Not measured
Test ID 3c	N/A	15dBm ± (5+TT)	Not measured
NOTE 1: In addition NOTE 2 in Table 6.2.2-1 in TS 36.101 [5] and/or NOTE 3 in Table 6.2.1-1 in TS 38.101-1 [2] shall apply to the tolerances. NOTE 2: TT for each frequency and channel bandwidth is specified in Table 6.2B.4.1.3.5-3 and Table 6.2B.4.1.3.5-4.

For UE not supporting DPS, the output power measured shall not exceed the values specified in Table 6.2B.4.1.3.5-2.

Table 6.2B.4.1.3.5-2: P_CMAX configured UE output power for UE not supporting DPS

	E-UTRA component carrier	NR component carrier	Total power measured over E-UTRA and NR component carriers
Test ID 1a	-10 dBm ± (7+TT)	-10 dBm ± (7+TT)	Not measured
Test ID 1b	10 dBm ± (6+TT)	10 dBm ± (6+TT)	Not measured
Test ID 1c	15 dBm ± (5+TT)	15 dBm ± (5+TT)	Not measured
Test ID 1d	Maximum output power with reduction as defined in Table 6.2.3.5-1 of TS 36.521-1 [10] for PC3 UE	N/A	Not measured
	Maximum output power with reduction as defined in Table 6.2.3_1.5-1 of TS 36.521-1 [10] for PC2 UE
Test ID 2a	-10dBm ± (7+TT)	N/A	Not measured
Test ID 2b	10dBm ± (6+TT)	N/A	Not measured
Test ID 2c	15dBm ± (5+TT)	N/A	Not measured
Test ID 3a	N/A	-10dBm ± (7+TT)	Not measured
Test ID 3b	N/A	10dBm ± (6+TT)	Not measured
Test ID 3c	N/A	15dBm ± (5+TT)	Not measured
NOTE 1: In addition NOTE 2 in Table 6.2.2-1 in TS 36.101 [5] and/or NOTE 3 in Table 6.2.1-1 in TS 38.101-1 [2] shall apply to the tolerances. NOTE 2: TT for each frequency and channel bandwidth is specified in Table 6.2B.4.1.3.5-3 and Table 6.2B.4.1.3.5-4.

Table 6.2B.4.1.3.5-3: Test Tolerance for UE maximum output power (Separate measurements over E-UTRA and NR CCs)

Uplink TX		f ≤ 3.0GHz	3.0GHz < f ≤ 4.2GHz	4.2GHz < f ≤ 6GHz
E-UTRA	BW ≤ 20MHz	0.7 dB	1.0 dB	1.3 dB
NR	BW ≤ 40MHz	0.7 dB	1.0 dB	1.0 dB
NR	40MHz < BW ≤ 100MHz	1.0 dB	1.0 dB	1.0 dB

Table 6.2B.4.1.3.5-4: Test Tolerance for UE maximum output power (Combined measurements of E-UTRA and NR CCs)

TT for overall output power
			NR
			BW ≤ 20MHz			20 MHz < BW ≤ 40MHz			40MHz < BW ≤ 100MHz
			f ≤ 3.0GHz	3.0GHz < f ≤ 4.2GHz	4.2GHz < f ≤ 6.0GHz	f ≤ 3.0GHz	3.0GHz < f ≤ 4.2GHz	4.2GHz < f ≤ 6.0GHz	f ≤ 3.0GHz	3.0GHz < f ≤ 4.2GHz	4.2GHz < f ≤ 6.0GHz
E-UTRA	BW ≤ 20MHz	f ≤ 3.0GHz	0.7 dB	1.0 dB	1.0 dB	0.7 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB
E-UTRA	BW ≤ 20MHz	3.0GHz < f ≤ 4.2GHz	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB

For the UE which supports inter-band EN-DC configuration, ΔT_IB,c in 6.2B.4.2 applies where unless otherwise stated, the same ΔT_IB,cis applicable to NR band(s) part for DC configurations which have the same NR operating band combination. Unless otherwise stated, ΔT_IB,c is set to zero.

6.2B.4.1.3_1 Configured Output Power for Inter-Band EN-DC within FR1 (2 E-UTRA CCs, 1 NR CC)

6.2B.4.1.3_1.1 Test purpose

Same test purpose as in clause 6.2B.4.1.3.1

6.2B.4.1.3_1.2 Test applicability

This test case applies to all types of E-UTRA UE release 16 and forward, supporting inter-band EN-DC with 2 E-UTRA CCs and 1 NR CC FR1.

6.2B.4.1.3_1.3 Minimum conformance requirements

The minimum conformance requirements are defined in clause 6.2B.4.1.0.1.3.

6.2B.4.1.3_1.4 Test description

6.2B.4.1.3_1.4.1 Initial conditions

Initial conditions are a set of test configurations the UE needs to be tested in and the steps for the SS to take with the UE to reach the correct measurement state.

The initial test configurations consist of environmental conditions, test frequencies and channel bandwidths based on EN-DC operating bands specified in clause 5.3B.1.2, channel bandwidths and sub-carrier spacings for the NR cell specified in TS 38.521-1 [8] clause 5.3 and channel bandwidth for the E-UTRA cell are specified in TS 36.521-1 [10] clause 5.4.2. All of these configurations shall be tested with applicable test parameters for each EN-DC configuration specified in clause 5.3B.1.2 and are shown in table 6.2B.4.1.3_1.4.1-1. The details of the uplink reference measurement channels (RMCs) are specified in Annex A.2. Configurations of PDSCH and PDCCH before measurement are specified in TS 36.521-1 [10] Annex C.2 and in TS 38.521-1 [8] Annex C.2 for E-UTRA CG and NR CG respectively.

Table 6.2B.4.1.3_1.4.1-1: Test configurations table for inter-band EN-DC

Initial Conditions
Test Environment as specified in TS 38.508-1 [5] clause 4.1			Normal, TL/VL, TL/VH, TH/VL, TH/VH
NR Test Frequencies as specified in TS 38.508-1 [5] clause 4.3.1 E-UTRA Test Frequencies as specified in TS 36.508-1 [11] clause 4.3.1			Mid range for MCG and SCG
Test EN-DC bandwidth combination as specified in TS 38.508-1 [5] clause 4.3.1			Lowest N_{RB_agg} for E-UTRA CCs and Lowest for NR CC1, Highest N_{RB_agg} for E-UTRA CCs and Highest for NR CC1
NR Test SCS as specified in Table 5.3.5-1 in TS 38.521-1 [8]			Highest
NR/E-UTRA Test Parameters for UE supporting DPS
Test ID (NOTE 3)	Downlink Configuration	EN-DC Uplink Configuration
		MCG – EUTRA PCC&SCC			SCG – NR
		Modulation	RB allocation (NOTE 2)	P_LTE	Modulation	RB allocation (NOTE 1)	P_NR
1a-1h	N/A	QPSK	Partial_Allocation	{-13, 12, 14, 17, 18, 19, 20, 23}	DFT-s-OFDM QPSK	Inner_Full	{-13, 12, 14, 17, 18, 19, 23, 23}
2a-2c		QPSK	Partial_Allocation	{-10, 10, 15}	N/A	N/A	{-10, 10, 15}
3a-3c		N/A	N/A	{-10, 10, 15}	DFT-s-OFDM QPSK	Inner Full	{-10, 10, 15}
NR/E-UTRA Test Parameters for UE not supporting DPS
Test ID (NOTE 3)	Downlink Configuration	EN-DC Uplink Configuration
		MCG – EUTRA PCC&SCC			SCG – NR
		Modulation	RB allocation (NOTE 2)	P_LTE	Modulation	RB allocation (NOTE 1)	P_NR
1a-1d	N/A	QPSK	Partial_Allocation	{-10, 10, 15, 23}	DFT-s-OFDM QPSK	Inner_Full	{-10, 10, 15, 23}
2a-2c		QPSK	Partial_Allocation	{-10, 10, 15}	N/A	N/A	{-10, 10, 15}
3a-3c		N/A	N/A	{-10, 10, 15}	DFT-s-OFDM QPSK	Inner_Full	{-10, 10, 15}
NOTE 1: The specific configuration of each RB allocation is defined in Table 6.1-1 in TS 38.521-1 [8]. NOTE 2: The specific configuration of each RB allocation is defined in Table 6.1-2 in current specification. NOTE 3: The suffix in Test ID identifies the configured power level being tested from the P_LTE and P_NR lists.

1. Connect the SS to the UE antenna connectors as shown in [6] TS 38.508-1 A.3.1.2.1 for SS diagram and A.3.2.1 for UE diagram.

2. The parameter settings for the E-UTRA cell are set up according to TS 36.508 [11] clause 4.4.3, and the parameter settings for the NR cell are set up according to TS 38.508-1 [6] clause 4.4.3.

3. Downlink signals are initially set up according to TS 36.521-1 [10] Annex C.0 and TS 38.521-1 [8] Annex C.0 for E-UTRA CG PCC and NR CG respectively, and uplink signals according to TS 36.521-1 [10] Annex H and TS 38.521-1 [8] Annex G for E-UTRA CG and NR CG respectively.

4. The UL Reference Measurement channels are set according to Table 6.2B.4.1.3_1.4.1-1.

5. Propagation conditions are set according to TS 36.521-1 [10] Annex B.0 and TS 38.521-1 [8] Annex B.0 for E-UTRA CG and NR CG respectively.

6.2B.4.1.3_1.4.2 Test procedure

1. Configure E-UTRA SCC according to TS 36.521-1 [10] Annex C.0, C.1, and Annex C.3.0 for all E-UTRA downlink physical channels.

2. The SS shall configure SCC as per TS 36.508 [11] clause 5.2A.4. Message contents are defined in clause 6.2B.4.1.3_1.4.3.

3. SS activates SCC by sending the MAC-CE according to TS 36.321 clauses 5.13 and 6.1.3.8. Wait for at least 2 seconds as per TS 36.133 [12] clause 8.3.3.2.

4. SS sends uplink scheduling information for each UL HARQ process via PDCCH DCI format 0 and DCI format 0_1 for C_RNTI to schedule the UL RMC according Table 6.2B.4.1.3_1.4.1-1 on E-UTRA PCC and SCC and NR CC respectively. Since the UE has no payload and no loopback data to send the UE sends uplink MAC padding bits on the UL RMC.

5. Send continuously uplink power control "up" commands in every uplink scheduling information to the UE until the UE transmits at its P_UMAX level; allow at least 200 ms from the first TPC command for the UE to reach P_UMAX level.

6. Measure the mean transmitted power over E-UTRA CG and NR CG respectively, or/and measure the sum of mean transmitted power over E-UTRA CG and NR CG according to Table 6.2B.4.1.3_1.5-1 and Table 6.2B.4.1.3_1.5-2. The period of the measurement shall be at least the continuous duration of one active sub-frame. For TDD, only slots consisting of only UL symbols are under test.

NOTE 1: When switching to DFT-s-OFDM waveform, as specified in the test configuration Table 6.2B.4.1.3_1.4.1-1, send an NR RRCReconfiguration message according to TS 38.508-1 [6] clause 4.6.3 Table 4.6.3-118 PUSCH-Config with TRANSFORM_PRECODER_ENABLED condition.

6.2B.4.1.3_1.4.3 Message contents

Message contents are according to TS 36.508 [11] clause 4.6.1 and TS 38.508-1 [6] clause 4.6.1 with the following exceptions.

Table 6.2B.4.1.3_1.4.3-1: RRCConnectionReconfiguration: tdm-PatternConfig if E-UTRA on FDD band and UE doesn’t support dynamic power sharing

Derivation Path: TS 36.508 [11], Table 4.6.1-8
Information Element		Value/remark	Comment	Condition
tdm-PatternConfig-r15 CHOICE{
setup SEQUENCE {
subframeAssignment-r15	sa2
harq-Offset-r15	0
}
}

Table 6.2B.4.1.3_1.4.3-2: SystemInfomationBlockType1: tdd-Config if E-UTRA on TDD band

Derivation Path: TS 36.508 [11], Table 4.6.3-23
Information Element	Value/remark	Comment	Condition
TDD-Config-DEFAULT ::= SEQUENCE {		Operating on TDD band
subframeAssignment	sa2
specialSubframePatterns	ssp7
}

Table 6.2B.4.1.3_1.4.3-3: RRCConnectionReconfiguration: nr-Config-r15

Derivation Path: TS 36.508 [11], Table 4.6.1-8
Information Element		Value/remark	Comment	Condition
p-MaxEUTRA-r15	Defined as P_LTE in Table 6.2B.4.1.3_1.4.1-1

Table 6.2B.4.1.3_1.4.3-4: PhysicalCellGroupConfig

Derivation Path: TS 38.508-1 [6], Table 4.6.3-106
Information Element	Value/remark	Comment	Condition
PhysicalCellGroupConfig ::= SEQUENCE {
p-NR-FR1	Defined as P_NR in Table 6.2B.4.1.3_1.4.1-1
}

Table 6.2B.4.1.3_1.4.3-5: RRCConnectionReconfiguration: p-MaxUE-FR1-r15

Derivation Path: TS 36.508 [11], Table 4.6.1-8
Information Element	Value/remark	Comment	Condition
nonCriticalExtension SEQUENCE {		RRCConnectionReconfiguration-v1530-IEs
p-MaxUE-FR1-r15	23		Power Class 3 UE
	26		Power Class 2 UE
}

6.2B.4.1.3_1.5 Test requirement

For UE supporting DPS, the output power measured shall not exceed the values specified in Table 6.2B.4.1.3_1.5-1.

Table 6.2B.4.1.3_1.5-1: P_CMAX configured UE output power for UE supporting DPS for PC3 UE

	E-UTRA CG	NR CG	Total power measured over all E-UTRA and NR component carriers
Test ID 1a	Not measured	Not measured	-10 dBm ± (7+TT)
Test ID 1b	Not measured	Not measured	15 dBm ± (6+TT)
Test ID 1c	Not measured	Not measured	17 dBm ± (5+TT)
Test ID 1d	Not measured	Not measured	20 dBm + (4+TT)/ – (6+TT)
Test ID 1e	Not measured	Not measured	21 dBm + (3+TT)/ – (5+TT)
Test ID 1f	Not measured	Not measured	22 dBm + (2+TT)/ – (5+TT)
Test ID 1g	Not measured	23 dBm + (2+TT) / 17 dBm – (5+TT)	23 dBm + (2+TT) / 21.8 dBm – (5+TT)
Test ID 1h	Maximum output power with reduction as defined in Table 6.2.3A.1.5-1 of TS 36.521-1 [10] for PC3 UE	N/A	Maximum output power with reduction as defined in Table 6.2.3A.1.5-1 of TS 36.521-1 [10] for PC3 UE
	Maximum output power with reduction as defined in Table 6.2.3A.1_3.5-1 of TS 36.521-1 [10] for PC2 UE		Maximum output power with reduction as defined in Table 6.2.3A.1_3.5-1 of TS 36.521-1 [10] for PC2 UE
Test ID 2a	-10 dBm ± (7+TT)	N/A	Not measured
Test ID 2b	10 dBm ± (6+TT)	N/A	Not measured
Test ID 2c	15 dBm ± (5+TT)	N/A	Not measured
Test ID 3a	N/A	-10 dBm ± (7+TT)	Not measured
Test ID 3b	N/A	10 dBm ± (6+TT)	Not measured
Test ID 3c	N/A	15 dBm ± (5+TT)	Not measured
NOTE 1: In addition NOTE 2 in Table 6.2.2-1 in TS 36.101 [5] and/or NOTE 3 in Table 6.2.1-1 in TS 38.101-1 [2] shall apply to the tolerances. NOTE 2: TT for each frequency and channel bandwidth is specified in Table 6.2B.4.1.3_1.5-3 and Table 6.2B.4.1.3_1.5-4.

For UE not supporting DPS, the output power measured shall not exceed the values specified in Table 6.2B.4.1.3_1.5-2.

Table 6.2B.4.1.3_1.5-2: P_CMAX configured UE output power for UE not supporting DPS

	E-UTRA CG	NR CG	Total power measured over all E-UTRA and NR component carriers
Test ID 1a	-10 dBm ± (7+TT)	-10 dBm ± (7+TT)	Not measured
Test ID 1b	10 dBm ± (6+TT)	10 dBm ± (6+TT)	Not measured
Test ID 1c	15 dBm ± (5+TT)	15 dBm ± (5+TT)	Not measured
Test ID 1d	Maximum output power with reduction as defined in Table 6.2.3A.1.5-1 of TS 36.521-1 [10] for PC3 UE	N/A	Not measured
	Maximum output power with reduction as defined in Table 6.2.3A.1_3.5-1 of TS 36.521-1 [10] for PC2 UE
Test ID 2a	-10 dBm ± (7+TT)	N/A	Not measured
Test ID 2b	10 dBm ± (6+TT)	N/A	Not measured
Test ID 2c	15 dBm ± (5+TT)	N/A	Not measured
Test ID 3a	N/A	-10 dBm ± (7+TT)	Not measured
Test ID 3b	N/A	10 dBm ± (6+TT)	Not measured
Test ID 3c	N/A	15 dBm ± (5+TT)	Not measured
NOTE 1: In addition NOTE 2 in Table 6.2.2A-1 in TS 36.101 [5] and/or NOTE 3 in Table 6.2.1-1 in TS 38.101-1 [2] shall apply to the tolerances. NOTE 2: TT for each frequency and channel bandwidth is specified in Table 6.2B.4.1.3_1.5-3 and Table 6.2B.4.1.3_1.5-4.

Table 6.2B.4.1.3_1.5-3: Test Tolerance for UE maximum output power (Separate measurements over E-UTRA and NR CCs)

Uplink TX		f ≤ 3.0GHz	3.0GHz < f ≤ 4.2GHz	4.2GHz < f ≤ 6GHz
E-UTRA	BW ≤ 20MHz	0.7 dB	1.0 dB	1.3 dB
NR	BW ≤ 40MHz	0.7 dB	1.0 dB	1.0 dB
NR	40MHz < BW ≤ 100MHz	1.0 dB	1.0 dB	1.0 dB

Table 6.2B.4.1.3_1.5-4: Test Tolerance for UE maximum output power (Combined measurements of E-UTRA and NR CCs)

TT for overall output power
			NR
			BW ≤ 20MHz			20 MHz < BW ≤ 40MHz			40MHz < BW ≤ 100MHz
			f ≤ 3.0GHz	3.0GHz < f ≤ 4.2GHz	4.2GHz < f ≤ 6.0GHz	f ≤ 3.0GHz	3.0GHz < f ≤ 4.2GHz	4.2GHz < f ≤ 6.0GHz	f ≤ 3.0GHz	3.0GHz < f ≤ 4.2GHz	4.2GHz < f ≤ 6.0GHz
E-UTRA	BW ≤ 20MHz	f ≤ 3.0GHz	0.7 dB	1.0 dB	1.0 dB	0.7 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB
E-UTRA	BW ≤ 20MHz	3.0GHz < f ≤ 4.2GHz	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB	1.0 dB

6.2B.4.1.4 Configured Output Power for Inter-Band EN-DC including FR2 (1 NR CC)

6.2B.4.1.4.1 Test purpose

Same test purpose as in clause 6.2.4.1 in TS 38.521-2 [9] for the NR carrier.

6.2B.4.1.4.2 Test applicability

This test case applies to all types of E-UTRA UE release 15 and forward, supporting inter-band EN-DC including FR2 with 1 NR UL CC.

The requirements of this test for NR carrier are covered in test cases 6.2B.1.1 Maximum output power for Inter-Band EN-DC including FR2, 6.2B.2.1 Maximum output power reduction for Inter-Band EN-DC including FR2 and 6.2B.3.1 UE maximum output power with additional requirements for Inter-Band EN-DC including FR2 to all types of NR UE release 15 and forward.

6.2B.4.1.4.3 Minimum conformance requirements

UE configured output power requirement for E-UTRA single carrier and CA operation specified in subclauses 6.2.5 and 6.2.5A of [10] and for NR single carrier and CA operation specified in subclause 6.2.4, 6.2A.4 and 6.2D.4 of [9] apply.

No exception requirements applicable to NR or E-UTRA. LTE anchor agnostic approach is applied.

The normative reference for this requirement is TS 38.101-3 [4] clause 6.2B.4.1.4.

6.2B.4.1.4.4 Test description

This test is covered by clause 6.2B.1.1 Maximum output power for Inter-Band EN-DC including FR2, 6.2B.2.1 Maximum output power reduction for Inter-Band EN-DC including FR2 and 6.2B.3.1 UE maximum output power with additional requirements for Inter-Band EN-DC including FR2.

6.2B.4.1.4.5 Test requirement

6.2B.4.1.4_1 Configured Output Power with Power Boost for Inter-Band EN-DC including FR2 (1 NR CC)

6.2B.4.1.4_1.1 Test purpose

Same test purpose as in clause 6.2.4_1.1 in TS 38.521-2 [9] for the NR carrier.

6.2B.4.1.4_1.2 Test applicability

This test case applies to all types of E-UTRA UE release 16 and forward, supporting inter-band EN-DC including FR2 with 1 NR UL CC and supporting mpr-PowerBoost-FR2-r16 UE capability.

6.2B.4.1.4_1.3 Minimum conformance requirements

UE configured output power requirement for E-UTRA single carrier and CA operation specified in subclauses 6.2.5 and 6.2.5A of [10] and for NR single carrier specified in subclause 6.2.4_1 of [9] apply.

No exception requirements applicable to NR or LTE. LTE anchor agnostic approach is applied.

The normative reference for this requirement is TS 38.101-3 [4] clause 6.2B.4.1.4.

6.2B.4.1.4_1.4 Test description

Same test description as in clause 6.2.4_1.4 in TS 38.521-2 [9] for the NR carrier with the following exceptions:

The initial test configurations for E-UTRA band consist of environmental conditions, test frequencies, and channel bandwidths based on E-UTRA bands specified in Table 4.6-1.

For Initial conditions as in clause 6.2.4_1.4.1 in TS 38.521-2 [9], the following steps will be added to configure E-UTRA component:

2.1. The parameter settings for the E-UTRA cell are set up according to TS 36.508 [11] clause 4.4.3 with E-UTRA channel bandwidth and test frequencies defined in Table 4.6-1.

3.1. Downlink E-UTRA signals are initially set up according to TS 36.521-1 [10] Annex C, clauses C.0, C.1 and C.3.0, and uplink signals according to Annex H, clauses H.1 and H.3.0.

4.1. The E-UTRA UL Reference Measurement channels are set according to Table 4.6-1.

Step 6 of Initial conditions as in clause 6.2.4_1 in TS 38.521-2 [9] is replaced by:

6. Ensure the UE is in state RRC_CONNECTED with generic procedure parameters Connectivity EN-DC, DC bearer MCG and SCG according to TS 38.508 [6] clause 4.5.

Same test procedure as in clause 6.2.4_1.4.2 in TS 38.521-2 [9] with the following steps added for E-UTRA component:

1.1 On the E-UTRA carrier, disable periodic and aperiodic CQI reports, disable SRS, set TimeAlignmentTimerDedicated IE to infinity and disable downlink and uplink scheduling, all as per Table 4.7-1 under clause 4.7.

6.2B.4.1.4_1.5 Test requirement

Same test requirement as in clause 6.2.4_1.5 in TS 38.521-2 [9] for the NR carrier.

6.2B.4.1.5 Configured Output Power for Inter-Band EN-DC including both FR1 and FR2

6.2B.4.1.5.1 Test purpose

Same test purpose as in clause 6.2.4.1 in TS 38.521-1 [8] for NR FR1 carrier and 6.2.4.1 in TS 38.521-2 [9] for NR FR2 carrier.

6.2B.4.1.5.2 Test applicability

The requirements in this test are not testable due to issues with combined testing of NR FR1 and E-UTRA in conducted mode with NR FR2 in radiated mode. Therefore, the conducted and radiated requirements are tested separately.

No test case details are specified. The EN-DC requirements for maximum output power apply and are tested as part of the EN-DC within FR1 and EN-DC including FR2 test cases in clause 6.2B.

6.2B.4.2 ΔT_IB,c for EN-DC

For the UE which supports inter-band EN-DC configuration, ΔT_IB,c in Tables below applies where unless otherwise stated, the same ΔT_IB,cis applicable to NR band(s) part for DC configurations which have the same NR operating band combination. Unless otherwise stated, ΔT_IB,c is set to zero.

Unless ΔT_IB,c is specified for the NE-DC configuration, the specified ΔT_IB,c for the EN-DC configuration including same bands as the corresponding NE-DC configuration is applicable for the NE-DC configuration.

6.2B.4.2.1 Intra-Band Contiguous EN-DC

ΔT_IB,c is not applicable for intra-band contiguous EN-DC.

6.2B.4.2.2 Intra-Band non-Contiguous EN-DC

ΔT_IB,c is not applicable for intra-band non-contiguous EN-DC.

6.2B.4.2.3 Inter-Band EN-DC within FR1

6.2B.4.2.3.1 ΔT_IB,c for EN-DC two bands

Table 6.2B.4.2.3.1-1: ΔT_IB,c due to EN-DC(two bands)

Inter-band EN-DC configuration	E-UTRA or NR Band	ΔT_IB,c (dB)
DC_1_n3	1	0.3
DC_1_n3	n3	0.3
DC_1_n5	1	0.3
DC_1_n5	n5	0.3
DC_1_n8	1	0.3
DC_1_n8	n8	0.3
DC_1_n28	1	0.3
DC_1_n28	n28	0.6
DC_1_n40	1	0.5
DC_1_n40	n40	0.5
DC_1_n51	1	0.6
DC_1_n51	n51	0.6
DC_1_n77	1	0.6
DC_1_n77	n77	0.8
DC_1_n78	1	0.3
DC_1_n78	n78	0.8
DC_2_n5	2	0.3
DC_2_n5	n5	0.3
DC_2_n41	2	0.5
	n41	0.4¹
	n41	0.9²
DC_2_n66	2	0.5
DC_2_n66	n66	0.5
DC_2_n71	2	0.3
DC_2_n71	n71	0.3
DC_2_n77 DC_2-2_n77	2	0.6
DC_2_n77 DC_2-2_n77	n77	0.8
DC_2_n78	2	0.6
DC_2_n78	n78	0.8
DC_3_n1	3	0.3
DC_3_n1	n1	0.3
DC_3_n5	3	0.3
DC_3_n5	n5	0.3
DC_3_n7	3	0.5
DC_3_n7	n7	0.5
DC_3_n8	3	0.3
DC_3_n8	n8	0.3
DC_3_n28	3	0.3
DC_3_n28	n28	0.3
DC_3_n40	3	0.5
DC_3_n40	n40	0.5
DC_3_n41	3	0.5
	n41	0.3³
	n41	0.8⁴
DC_3_n51	3	0.3
DC_3_n51	n51	0.3
DC_3_n77	3	0.6
DC_3_n77	n77	0.8
DC_3_n78	3	0.6
DC_3_n78	n78	0.8
DC_5_n2, DC_5-5_n2	5	0.3
DC_5_n2, DC_5-5_n2	n2	0.3
DC_5_n40	5	0.3
DC_5_n40	n40	0.3
DC_5_n66	5	0.3
DC_5_n66	n66	0.3
DC_5_n77	5	0.6
DC_5_n77	n77	0.8
DC_5_n78	5	0.6
DC_5_n78	n78	0.8
DC_7_n1	7	0.6
DC_7_n1	n1	0.5
DC_7_n3	7	0.5
DC_7_n3	n3	0.5
DC_7_n5	7	0.3
DC_7_n5	n5	0.3
DC_7_n8	7	0.3
DC_7_n8	n8	0.6
DC_7_n28	7	0.3
DC_7_n28	n28	0.3
DC_7_n51	7	0.3
DC_7_n51	n51	0.3
DC_7_n66, DC_7-7_n66	7	0.5
DC_7_n66, DC_7-7_n66	n66	0.5
DC_7_n78, DC_7-7_n78	7	0.5
DC_7_n78, DC_7-7_n78	n78	0.8
DC_8_n1	8	0.3
DC_8_n1	n1	0.3
DC_8_n3	8	0.3
DC_8_n3	n3	0.3
DC_8_n20	8	0.4
DC_8_n20	n20	0.4
DC_8_n28	8	0.6
DC_8_n28	n28	0.5
DC_8_n40	8	0.3
DC_8_n40	n40	0.3
DC_8_n41	8	0.3
DC_8_n41	n41	0.3
DC_8_n77	8	0.6
DC_8_n77	n77	0.8
DC_8_n78	8	0.6
DC_8_n78	n78	0.8
DC_11_n77	11	0.4
DC_11_n77	n77	0.8
DC_11_n78	11	0.4
DC_11_n78	n78	0.8
DC_12_n5	12	0.4
DC_12_n5	n5	0.8
DC_12_n66	12	0.8
DC_12_n66	n66	0.3
DC_12_n78	12	0.5
DC_12_n78	n78	0.8
DC_13_n2	13	0.3
DC_13_n2	n2	0.3
DC_13_n66	13	0.3
DC_13_n66	n66	0.3
DC_13_n77	13	0.5
DC_13_n77	n77	0.8
DC_14_n2	14	0.3
DC_14_n2	n2	0.3
DC_14_n66	14	0.3
DC_14_n66	n66	0.3
DC_18_n77	18	0.3
DC_18_n77	n77	0.8
DC_18_n78	18	0.3
DC_18_n78	n78	0.8
DC_19_n77	19	0.3
DC_19_n77	n77	0.8
DC_19_n78	19	0.3
DC_19_n78	n78	0.8
DC_20_n1	20	0.3
DC_20_n1	n1	0.3
DC_20_n3	20	0.3
DC_20_n3	n3	0.3
DC_20_n7	20	0.3
DC_20_n7	n7	0.3
DC_20_n8	20	0.4
DC_20_n8	n8	0.4
DC_20_n28	20	0.5
DC_20_n28	n28	0.5
DC_20_n51	20	0.5
DC_20_n51	n51	0.5
DC_20_n77	20	0.6
DC_20_n77	n77	0.8
DC_20_n78	20	0.6
DC_20_n78	n78	0.8
DC_21_n77	21	0.4
DC_21_n77	n77	0.8
DC_21_n78	21	0.4
DC_21_n78	n78	0.8
DC_25_n41	25	0.5
	n41	0.4¹
	n41	0.9²
DC_26_n41	26	0.3
DC_26_n41	n41	0.3
DC_26_n77	26	0.3
DC_26_n77	n77	0.8
DC_26_n78	26	0.3
DC_26_n78	n78	0.8
DC_28_n5	28	0.5
DC_28_n5	n5	0.5
DC_28_n51	28	0.5
DC_28_n51	n51	0.5
DC_28_n77	28	0.5
DC_28_n77	n77	0.8
DC_28_n78	28	0.5
DC_28_n78	n78	0.8
DC_30_n5	30	0.3
DC_30_n5	n5	0.3
DC_30_n66	30	0.5
DC_30_n66	n66	0.8
DC_38_n78	n78	0.5
DC_39_n41	39	0.5
DC_39_n41	n41	0.5
DC_39_n78	39	0.3
DC_39_n78	n78	0.8
DC_39_n79	39	0.3
DC_39_n79	n79	0.8
DC_40_n1	n1	0.5
DC_40_n1	40	0.5
DC_40_n41⁵	40	0.5
DC_40_n41⁵	n41	0.5
DC_40_n77	n77	0.5
DC_40_n78	n78	0.5⁶
DC_40_n79	40	0.3
DC_40_n79	n79	0.8
DC_41_n77	41	0.3
DC_41_n77	n77	0.8
DC_41_n78	41	0.3
DC_41_n78	n78	0.8
DC_41_n79	41	0.3
DC_41_n79	n79	0.8
DC_42_n51	42	0.6
DC_42_n51	n51	0.8
DC_48_n5	48	0.3
DC_48_n5	n5	0.3
DC_48_n66	48	0.8
DC_48_n66	n66	0.6
DC_66_n2	66	0.5
DC_66_n2	n2	0.5
DC_66_n5	66	0.3
DC_66_n5	n5	0.3
DC_66_n41	66	0.5
	n41	0.8¹
	n41	1.3²
DC_66_n71	66	0.3
DC_66_n71	n71	0.3
DC_66_n77 DC_66-66_n77 DC_66-66-66_n77	66	0.6
DC_66_n77 DC_66-66_n77 DC_66-66-66_n77	n77	0.8
DC_66_n78	66	0.6
DC_66_n78	n78	0.8
NOTE 1: The requirement is applied for UE transmitting on the frequency range of 2545-2690 MHz. NOTE 2: The requirement is applied for UE transmitting on the frequency range of 2496-2545 MHz. NOTE 3: Applicable for the frequency range of 2515 – 2690 MHz. NOTE 4: Applicable for the frequency range of 2496 – 2515 MHz. NOTE 5: Applicable for UE supporting inter-band EN-DC without simultaneous Rx/Tx. NOTE 6: Only applicable for UE supporting inter-band carrier aggregation with uplink in one E-UTRA band and without simultaneous Rx/Tx.

6.2B.4.2.3.2 ΔT_IB,c for EN-DC three bands

Table 6.2B.4.2.3.2-1: ΔT_IB,c due to EN-DC (three bands)

Inter-band EN-DC configuration	E-UTRA or NR Band	ΔT_IB,c (dB)
DC_1-3_n28	1	0.3
	3	0.3
	n28	0.6
DC_1-3_n77	1	0.6
	3	0.6
	n77	0.8
DC_1-3_n78	1	0.6
	3	0.6
	n78	0.8
DC_1-3_n79	1	0.3
DC_1-3_n79	3	0.3
DC_1-5_n78	1	0.3
	5	0.6
	n78	0.8
DC_1-7_n3	1	0.6
	7	0.6
	n3	0.6
DC_1-7_n28	1	0.5
	7	0.6
	n28	0.6
DC_1-7_n78 DC_1-7-7_n78	1	0.6
	7	0.6
	n78	0.8
DC_1-8_n3	1	0.3
	8	0.3
	n3	0.3
DC_1-8_n78	1	0.3
	8	0.6
	n78	0.8
DC_1-18_n77	1	0.3
	18	0.3
	n77	0.8
DC_1-18_n78	1	0.3
	18	0.3
	n78	0.8
DC_1-19_n77	1	0.3
	19	0.3
	n77	0.8
DC_1-19_n78	1	0.3
	19	0.3
	n78	0.8
DC_1-19_n79	1	0.3
DC_1-19_n79	19	0.3
DC_1-20_n3	1	0.3
	20	0.3
	n3	0.3
DC_1-20_n28	1	0.3
	20	0.6
	n28	0.6
DC_1-20_n78	1	0.3
	20	0.3
	n78	0.8
DC_1-21_n77	1	0.3
	21	0.3
	n77	0.8
DC_1-21_n78	1	0.6
	21	0.4
	n78	0.8
DC_1-21_n79	1	0.3
DC_1-21_n79	21	0.3
DC_1-28_n3	1	0.3
	28	0.6
	n3	0.3
DC_1-28_n77	1	0.3
	28	0.6
	n77	0.8
DC_1-28_n78 DC_1_n28-n78	1	0.3
	28 or n28	0.6
	n78	0.8
DC_1_n28-n79	1	0.3
DC_1_n28-n79	n28	0.3
DC_1-41_n28	1	0.5
	41	0.5
	n28	0.5
DC_1-41_n77	1	0.5
	41	0.5
	n77	0.8
DC_1-41_n78	1	0.5
	41	0.5
	n78	0.8
DC_1-41_n79	1	0.5
DC_1-41_n79	41	0.5
DC_1-42_n77	1	0.6
	42	0.8
	n77	0.8
DC_1-42_n78	1	0.3
	42	0.8
	n78	0.8
DC_1-42_n79	1	0.3
DC_1-42_n79	42	0.8
DC_1_n77-n79	1	0.6
DC_1_n77-n79	n77	0.8
DC_1_SUL_n78-n84	1	0.3
	n78	0.8
	n84	0.3
DC_1_n78-n79	1	0.3
	n78	0.8
	n79	0.5
DC_2-5_n66	2	0.5
	5	0.3
	n66	0.5
DC_2-14_n2	2	0.3
	14	0.3
	n2	0.3
DC_2-14_n66 DC_2-2-14_n66	2	0.5
	14	0.3
	n66	0.5
DC_2-30_n66	2	0.5
	30	0.3
	n66	0.5
DC_2-66_n5	2	0.5
	66	0.5
	n5	0.3
DC_2-66_n41	2	0.5
	66	0.5
	n41	0.8¹
	n41	1.3²
DC_2-66_n71	2	0.5
	66	0.5
	n71	0.3
DC_2-(n)71	2	0.3
	71	0.3
	n71	0.3
DC_3_n3-n77	3	0.6
	n3	0.6
	n77	0.8
DC_3_n3-n78	3	0.6
	n3	0.6
	n78	0.8
DC_3-5_n78	3	0.6
	5	0.6
	n78	0.8
DC_3-7_n28	3	0.5
	7	0.5
	n28	0.3
DC_3-7_n78, DC_3-7-7_n78	3	0.6
	7	0.6
	n78	0.8
DC_3-8_n78	3	0.6
	8	0.6
	n78	0.8
DC_3-18_n77	3	0.6
	18	0.3
	n77	0.8
DC_3-18_n78	3	0.6
	18	0.3
	n78	0.8
DC_3-19_n77	3	0.6
	19	0.3
	n77	0.8
DC_3-19_n78	3	0.6
	19	0.3
	n78	0.8
DC_3-19_n79	3	0.3
DC_3-19_n79	19	0.3
DC_3-20_n1	3	0.3
	20	0.3
	n1	0.3
DC_3-20_n28	3	0.3
	20	0.5
	n28	0.5
DC_3-20_n78	3	0.5
	20	0.3
	n78	0.8
DC_3-21_n77	3	0.8
	21	0.9
	n77	0.8
DC_3-21_n78	3	0.8
	21	0.9
	n78	0.8
DC_3-21_n79	3	0.8
DC_3-21_n79	21	0.9
DC_3-28_n78	3	0.5
	28	0.3
	n78	0.8
DC_3_n28-n78	3	0.5
	n28	0.3
	n78	0.8
DC_3-38_n78	3	0.6
DC_3-38_n78	n78	0.8
DC_3-40_n1	3	0.5
	40	0.5
	n1	0.5
DC_3-41_n28	3	0.5
	41	0.3³
	41	0.8⁴
	n28	0.3
DC_3-41_n41	3	0.5
	41	0.3³
	41	0.8⁴
	n41	0.3³
	n41	0.8⁴
DC_3-41_n77	3	0.6
	41	0.3³
	41	0.8⁴
	n77	0.8
DC_3-41_n78	3	0.6
	41	0.3¹
	41	0.8²
	n78	0.8
DC_3-42_n77	3	0.6
	42	0.8
	n77	0.8
DC_3-42_n78	3	0.6
	42	0.8
	n78	0.8
DC_3-42_n79	3	0.6
DC_3-42_n79	42	0.8
DC_3_n77-n79	3	0.6
DC_3_n77-n79	n77	0.8
DC_3_n78-n79	3	0.6
	n78	0.8
	n79	0.5
DC_3_SUL_n78-n80	3	0.6
	n78	0.8
	n80	0.6
DC_3_SUL_n78-n82	3	0.5
	n78	0.8
	n82	0.3
DC_5-7_n78, DC_5-7-7_n78	5	0.6
	7	0.6
	n78	0.8
DC_5-30_n66	5	0.3
	30	0.3
	n66	0.5
DC_7-20_n28	7	0.3
	20	0.6
	n28	0.6
DC_7-20_n1	7	0.6
	20	0.3
	n1	0.5
DC_7-20_n3	7	0.5
	20	0.3
	n3	0.5
DC_7-20_n78	7	0.3
	20	0.3
	n78	0.8
DC_7-28_n3	7	0.5
	28	0.3
	n3	0.5
DC_7-28_n78	7	0.3
	28	0.3
	n78	0.8
DC_7_n28-n78	7	0.3
	n28	0.3
	n78	0.8
DC_7-46_n78	7	0.5
DC_7-46_n78	n78	0.8
DC_8_SUL_n78- n81	8	0.6
	n78	0.8
	n81	0.6
DC_14-66_n2 DC_14-66-66_n2	14	0.3
	66	0.5
	n2	0.5
DC_14-66_n66	14	0.3
	66	0.3
	n66	0.3
DC_18-28_n77	18	0.5
	28	0.5
	n77	0.8
DC_18-28_n78	18	0.5
	28	0.5
	n78	0.8
DC_18-28_n79	18	0.5
DC_18-28_n79	28	0.5
DC_18-41_n3	18	0.3
	41	0.3³
	41	0.8⁴
	n3	0.5
DC_18-41_n77	18	0.3
	41	0.3³
	41	0.8⁴
	n77	0.8
DC_18-41_n78	18	0.3
	41	0.3³
	41	0.8⁴
	n78	0.8
DC_19-21_n77	19	0.3
	21	0.4
	n77	0.8
DC_19-21_n78	19	0.3
	21	0.4
	n78	0.8
DC_19-21_n79	19	0.3
DC_19-21_n79	21	0.4
DC_19-42_n77	19	0.3
	42	0.8
	n77	0.8
DC_19-42_n78	19	0.3
	42	0.8
	n78	0.8
DC_19-42_n79	19	0.3
DC_19-42_n79	42	0.8
DC_19_n77-n79	19	0.3
DC_19_n77-n79	n77	0.8
DC_19_n78-n79	19	0.3
	n78	0.8
	n79	0.5
DC_20_n8-n75	20	0.4
DC_20_n8-n75	n8	0.4
DC_20_n28-n75	20	0.5
DC_20_n28-n75	n28	0.7
DC_20_n28-n78	20	0.6
	n28	0.6
	n78	0.8
DC_20_n75-n78	20	0.5
DC_20_n75-n78	n78	0.8
DC_20_n76-n78	20	0.5
DC_20_n76-n78	n78	0.8
DC_20_SUL_n78-n82	20	0.6
	n78	0.8
	n82	0.6
DC_20_SUL_n78-n83	20	0.8
	n78	0.8
	n83	0.8
DC_21-42_n77	21	0.4
	42	0.8
	n77	0.8
DC_21-42_n78	21	0.4
	42	0.8
	n78	0.8
DC_21-42_n79	21	0.4
DC_21-42_n79	42	0.8
DC_21_n77-n79	21	0.4
DC_21_n77-n79	n77	0.8
DC_21_n78-n79	21	0.4
	n78	0.8
	n79	0.5
DC_28_n7-n78	28	0.3
	n7	0.3
	n78	0.8
DC_28-42_n77	28	0.5
	42	0.8
	n77	0.8
DC_28-42_n78	28	0.5
	42	0.8
	n78	0.8
DC_28-42_n79	28	0.5
DC_28-42_n79	42	0.8
DC_28_SUL_n78-n83	28	0.5
	n78	0.8
	n83	0.5
DC_41-42_n77	41	0.5
	42	0.8
	n77	0.8
DC_41-42_n78	41	0.5
	42	0.8
	n78	0.8
DC_41-42_n79	41	0.3
DC_41-42_n79	42	0.8
DC_66_(n)71	66	0.3
	71	0.3
	n71	0.3
DC_66_SUL_n78-n86	66	0.6
	n78	0.8
	n86	0.6
NOTE 1: The requirement is applied for UE transmitting on the frequency range of 2545-2690 MHz. NOTE 2: The requirement is applied for UE transmitting on the frequency range of 2496-2545 MHz. NOTE 3: The requirement is applied for UE transmitting on the frequency range of 2515 – 2690 MHz. NOTE 4: The requirement is applied for UE transmitting on the frequency range of 2496 – 2515 MHz.

6.2B.4.2.3.3 ΔTIB,c for EN-DC four bands

Table 6.2B.4.2.3.3-1: ΔT_IB,c due to EN-DC(four bands)

Inter-band EN-DC configuration	E-UTRA or NR Band	ΔT_IB,c (dB)
DC_1-3-5_n78	1	0.6
	3	0.6
	5	0.3
	n78	0.8
DC_1-3-7_n28	1	0.6
	3	0.6
	7	0.6
	n28	0.6
DC_1-3-7_n78 DC_1-3-7-7_n78	1	0.7
	3	0.7
	7	0.7
	n78	0.8
DC_1-3-8_n78	1	0.6
	3	0.6
	8	0.6
	n78	0.8
DC_1-3-19_n78	1	0.6
	3	0.6
	19	0.3
	n78	0.8
DC_1-3-19_n79	1	0.3
	3	0.3
	19	0.3
DC_1-3-20_n28	1	0.3
	3	0.3
	20	0.6
	n28	0.6
DC_1-3-20_n78	1	0.6
	3	0.6
	20	0.3
	n78	0.8
DC_1-3-21_n77	1	0.6
	3	0.8
	21	0.9
	n77	0.8
DC_1-3-21_n78	1	0.6
	3	0.8
	21	0.9
	n78	0.8
DC_1-3-21_n79	1	0.3
	3	0.8
	21	0.9
DC_1-3-28_n77	1	0.6
	3	0.6
	28	0.6
	n77	0.8
DC_1-3-28_n78 DC_1-3_n28-n78	1	0.6
	3	0.6
	28 or n28	0.6
	n78	0.8
DC_1-3-28_n79	1	0.6
	3	0.6
	28	0.6
DC_1-3-42_n77	1	0.6
	3	0.6
	42	0.8
	n77	0.8
DC_1-3-42_n78	1	0.6
	3	0.6
	42	0.8
	n78	0.8
DC_1-3-42_n79	1	0.6
	3	0.6
	42	0.8
DC_1-5-7_n78 DC_1-5-7-7_n78	1	0.6
	5	0.6
	7	0.6
	n78	0.8
DC_1-7-20_n28	1	0.5
	7	0.6
	20	0.6
	n28	0.6
DC_1-7-20_n78	1	0.6
	7	0.7
	20	0.4
	n78	0.8
DC_1-7_n28-n78	1	0.6
	7	0.6
	n28	0.6
	n78	0.8
DC_1-18-28_n77	1	0.3
	18	0.5
	28	0.5
	n77	0.8
DC_1-18-28_n78	1	0.3
	18	0.5
	28	0.5
	n78	0.8
DC_1-18-28_n79	1	0.3
	18	0.5
	28	0.5
DC_1-19-42_n77	1	0.6
	19	0.3
	42	0.8
	n77	0.8
DC_1-19-42_n78	1	0.3
	19	0.3
	42	0.8
	n78	0.8
DC_1-19-42_n79	1	0.3
	19	0.3
	42	0.8
DC_1-20_n28-n78	1	0.3
	20	0.6
	n28	0.6
	n78	0.8
DC_1-21-28_n77	1	0.6
	21	0.4
	28	0.6
	n77	0.8
DC_1-21-28_n78	1	0.3
	21	0.4
	28	0.6
	n78	0.8
DC_1-21-28_n79	1	0.3
	21	0.4
	28	0.6
DC_1-21-42_n77	1	0.6
	21	0.4
	42	0.8
	n77	0.8
DC_1-21-42_n78	1	0.3
	21	0.4
	42	0.8
	n78	0.8
DC_1-21-42_n79	1	0.3
	21	0.4
	42	0.8
DC_1-28-42_n77	1	0.6
	28	0.6
	42	0.8
	n77	0.8
DC_1-28-42_n78	1	0.3
	28	0.6
	42	0.8
	n78	0.8
DC_1-28-42_n79	1	0.3
	28	0.6
	42	0.8
DC_1-41-42_n77	1	0.5
	41	0.5
	42	0.8
	n77	0.8
DC_1-41-42_n78	1	0.5
	41	0.5
	42	0.8
	n78	0.8
DC_1-41-42_n79	1	0.5
	41	0.5
	42	0.8
DC_2-7-13_n66 DC_2-7-7-13_n66	2	0.5
	7	0.5
	13	0.3
	n66	0.5
DC_2-7-66_n66 DC_2-7-7-66_n66	2	0.5
	7	0.5
	66	0.5
	n66	0.5
DC_2-7-66_n78 DC_2-7-7-66_n78	2	0.6
	7	0.5
	66	0.6
	n78	0.8
DC_2-14-66_n2 DC_2-14-66-66_n2	2	0.5
	14	0.3
	66	0.5
	n2	0.5
DC_2-14-66_n66 DC_2-2-14-66_n66	2	0.5
	14	0.3
	66	0.5
	n66	0.5
DC_2-66-(n)71	2	0.5
	66	0.5
	71	0.3
	n71	0.3
DC_3-5-7_n78 DC_3-5-7-7_n78	3	0.6
	5	0.6
	7	0.6
	n78	0.8
DC_3-7-20_n28	3	0.5
	7	0.5
	20	0.6
	n28	0.5
DC_3-7-20_n78	3	0.6
	7	0.6
	20	0.3
	n78	0.8
DC_3-7-28_n78	3	0.6
	7	0.6
	28	0.6
	n78	0.8
DC_3-7_n28-n78	3	0.6
	7	0.6
	n28	0.6
	n78	0.8
DC_3-19-21_n77	3	0.8
	19	0.3
	21	0.9
	n77	0.8
DC_3-19-21_n78	3	0.8
	19	0.3
	21	0.9
	n78	0.8
DC_3-19-21_n79	3	0.8
	19	0.3
	21	0.9
DC_3-19-42_n77	3	0.6
	19	0.3
	42	0.8
	n77	0.8
DC_3-19-42_n78	3	0.6
	19	0.3
	42	0.8
	n78	0.8
DC_3-19-42_n79	3	0.6
	19	0.3
	42	0.8
DC_3-20_n28-n78	3	0.6
	20	0.6
	n28	0.6
	n78	0.8
DC_3-21-42_n77	3	0.8
	21	0.9
	42	0.8
	n77	0.8
DC_3-21-42_n78	3	0.8
	21	0.9
	42	0.8
	n78	0.8
DC_3-21-42_n79	3	0.8
	21	0.9
	42	0.8
DC_3-28-42_n77	3	0.6
	28	0.5
	42	0.8
	n77	0.8
DC_3-28-42_n78	3	0.6
	28	0.5
	42	0.8
	n78	0.8
DC_3-28-42_n79	3	0.6
	28	0.5
	42	0.8
DC_7-20_n28-n78	7	0.3
	20	0.6
	n28	0.6
	n78	0.8
DC_19-21-42_n77	19	0.3
	21	0.4
	42	0.8
	n77	0.8
DC_19-21-42_n78	19	0.3
	21	0.4
	42	0.8
	n78	0.8
DC_19-21-42_n79	19	0.3
	21	0.4
	42	0.8
DC_21-28-42_n77	21	0.4
	28	0.5
	42	0.8
	n77	0.8
DC_21-28-42_n78	21	0.4
	28	0.5
	42	0.8
	n78	0.8
DC_21-28-42_n79	21	0.4
	28	0.5
	42	0.8

6.2B.4.2.3.4 ΔTIB,c for EN-DC five bands

Table 6.2B.4.2.3.4-1: ΔT_IB,c due to EN-DC (five bands)

Inter-band EN-DC configuration	E-UTRA or NR Band	ΔT_IB,c (dB)
DC_1-3-5-7_n78, DC_1-3-5-7-7_n78	1	0.6
	3	0.6
	5	0.6
	7	0.6
	n78	0.8
DC_1-3-7-20_n28	1	0.6
	3	0.6
	7	0.6
	20	0.6
	n28	0.6
DC_1-3-7-20_n78	1	0.6
	3	0.6
	7	0.6
	20	0.6
	n78	0.6
DC_1-3-7_n28-n78	1	0.7
	3	0.7
	7	0.7
	n28	0.6
	n78	0.8
DC_1-3-19-21_n77	1	0.6
	3	0.8
	19	0.3
	21	0.9
	n77	0.8
DC_1-3-19-21_n78	1	0.6
	3	0.8
	19	0.3
	21	0.9
	n78	0.8
DC_1-3-19-21_n79	1	0.3
	3	0.8
	19	0.3
	21	0.9
DC_1-3-19-42_n77	1	0.6
	3	0.6
	19	0.3
	42	0.8
	n77	0.8
DC_1-3-19-42_n78	1	0.6
	3	0.6
	19	0.3
	42	0.8
	n78	0.8
DC_1-3-19-42_n79	1	0.6
	3	0.6
	19	0.3
	42	0.8
DC_1-3-20_n28-n78	1	0.6
	3	0.6
	20	0.6
	n28	0.6
	n78	0.8
DC_1-3-21-42_n77	1	0.6
	3	0.8
	21	0.9
	42	0.8
	n77	0.6
DC_1-3-21-42_n78	1	0.6
	3	0.8
	21	0.9
	42	0.8
	n78	0.6
DC_1-3-21-42_n79	1	0.6
	3	0.8
	21	0.9
	42	0.8
DC_1-3-28-42_n77	1	0.6
	3	0.6
	28	0.6
	42	0.8
	n77	0.8
DC_1-3-28-42_n78	1	0.6
	3	0.6
	28	0.6
	42	0.8
	n78	0.8
DC_1-3-28-42_n79	1	0.6
	3	0.6
	28	0.6
	42	0.8
DC_1-7-20_n28-n78	1	0.6
	7	0.7
	20	0.6
	n28	0.6
	n78	0.8
DC_1-19-21-42_n77	1	0.3
	19	0.3
	21	0.4
	42	0.8
	n77	0.8
DC_1-19-21-42_n78	1	0.3
	19	0.3
	21	0.4
	42	0.8
	n78	0.8
DC_1-19-21-42_n79	1	0.3
	19	0.3
	21	0.4
	42	0.8
DC_1-21-28-42_n77	1	0.6
	21	0.4
	28	0.6
	42	0.8
	n77	0.8
DC_1-21-28-42_n78	1	0.3
	21	0.4
	28	0.6
	42	0.8
	n78	0.8
DC_1-21-28-42_n79	1	0.3
	21	0.4
	28	0.6
	42	0.8
DC_3-7-20_n28-n78	3	0.6
	7	0.6
	20	0.6
	n28	0.6
	n78	0.8

6.2B.4.2.3.5 ΔTIB,c for EN-DC six bands

Table 6.2B.4.2.3.5-1: ΔT_IB,c due to EN-DC (six bands)

Inter-band EN-DC configuration	E-UTRA or NR Band	ΔT_IB,c (dB)
DC_1-3-7-20_n28-n78	1	0.7
	3	0.7
	7	0.7
	20	0.6
	n28	0.6
	n78	0.8

6.2B.4.2.3a Inter-band NE-DC within FR1

Unless ΔT_IB,c is specified in this clause, the value of ΔT_IB,c for the correspondingly specified EN-DC configuration in clause 6.2B.4.2.3 is applicable.

Table 6.2B.4.2.3a-1: ΔT_IB,c due to NE-DC(two bands)

Inter-band NE-DC configuration	E-UTRA or NR Band	ΔT_IB,c (dB)
DC_n28_39	n28	0.3
DC_n28_39	39	0.3

6.2B.4.2.4 Inter-band EN-DC including FR2

6.2B.4.2.4.1 ΔT_IB,c for EN-DC two bands

Unless otherwise stated, ΔT_IB,c for E-UTRA and FR2 NR bands of inter-band EN-DC combinations defined in table 5.5B.5.1-1 is set to zero.

Table 6.2B.4.2.4.1-1: Void

6.2B.4.2.4.2 ΔT_IB,c for EN-DC three bands

Unless otherwise stated, ΔT_IB,c for FR2 NR bands is set to zero, and ΔT_IB,c for constituent E-UTRA bands for inter-band EN-DC defined in table 5.5B.5.2-1 is the same as those for the corresponding E-UTRA CA configuration specified in TS 36.101 [4], without the FR2 NR bands.

Table 6.2B.4.2.4.2-1: Void

6.2B.4.2.4.3 ΔT_IB,c for EN-DC four bands

Unless otherwise stated, ΔT_IB,c for FR2 NR bands is set to zero, and ΔT_IB,c for constituent E-UTRA bands for inter-band EN-DC defined in table 5.5B.5.3-1 is the same as those for the corresponding E-UTRA CA configuration specified in TS 36.101 [4], without the FR2 NR bands.

Table 6.2B.4.2.4.3-1: Void

6.2B.4.2.4.4 ΔT_IB,c for EN-DC five bands

Unless otherwise stated, ΔT_IB,c for FR2 NR bands is set to zero, and ΔT_IB,c for constituent E-UTRA bands for inter-band EN-DC defined in table 5.5B.5.4-1 is the same as those for the corresponding E-UTRA CA configuration specified in TS 36.101 [4], without the FR2 NR bands.

Table 6.2B.4.2.4.4-1: Void

6.2B.4.2.4.5 Void

6.2B.4.2.5 Inter-band EN-DC including both FR1 and FR2

6.2B.4.2.5.1 ΔT_IB,c for EN-DC three bands

Unless otherwise stated, for inter-band EN-DC configurations defined in table 5.5B.6.2-1, ΔT_IB,c for constituent FR2 NR bands is set to zero, and ΔT_IB,c for constituent E-UTRA and FR1 NR bands is the same as those for the corresponding inter band EN-DC configuration without the FR2 bands specified in 6.2B.4.2.3.

Table 6.2B.4.2.5.1-1: Void

6.2B.4.2.5.2 ΔT_IB,c for EN-DC four bands

Unless otherwise stated, for inter-band EN-DC configurations defined in table 5.5B.6.3-1, ΔT_IB,c for constituent FR2 NR bands is set to zero, and ΔT_IB,c for constituent E-UTRA and FR1 NR bands is the same as those for the corresponding inter band EN-DC configuration without the FR2 bands specified in 6.2B.4.2.3.

6.2B.4.2.5.3 ΔT_IB,c for EN-DC five bands

Unless otherwise stated, for inter-band EN-DC configurations defined in table 5.5B.6.4-1, ΔT_IB,c for constituent FR2 NR bands is set to zero, and ΔT_IB,c for constituent E-UTRA and FR1 NR bands is the same as those for the corresponding inter band EN-DC configuration without the FR2 bands specified in 6.2B.4.2.3.

6.2B.4.2.5.4 ΔT_IB,c for EN-DC six bands

Unless otherwise stated, for inter-band EN-DC configurations defined in table 5.5B.6.5-1, ΔT_IB,c for constituent FR2 NR bands is set to zero, and ΔT_IB,c for constituent E-UTRA and FR1 NR bands is the same as those for the corresponding inter band EN-DC configuration without the FR2 bands specified in 6.2B.4.2.3.

6.2B.4.1 Configured Output Power Level for EN-DC

6.2B.4.1.0 Minimum Conformance Requirements

6.2B.4.1.1 Configured Output Power Level for Intra-Band Contiguous EN-DC

6.2B.4.1.2 Configured Output Power for Intra-Band Non-Contiguous EN-DC

6.2B.4.1.3 Configured Output Power for Inter-Band EN-DC within FR1 (1 E-UTRA CC, 1 NR CC)

6.2B.4.1.3_1 Configured Output Power for Inter-Band EN-DC within FR1 (2 E-UTRA CCs, 1 NR CC)

6.2B.4.1.4 Configured Output Power for Inter-Band EN-DC including FR2 (1 NR CC)

6.2B.4.1.4_1 Configured Output Power with Power Boost for Inter-Band EN-DC including FR2 (1 NR CC)

6.2B.4.1.5 Configured Output Power for Inter-Band EN-DC including both FR1 and FR2

6.2B.4.2 ΔTIB,c for EN-DC

6.2B.4.2.1 Intra-Band Contiguous EN-DC

6.2B.4.2.2 Intra-Band non-Contiguous EN-DC

6.2B.4.2.3 Inter-Band EN-DC within FR1

6.2B.4.2.3a Inter-band NE-DC within FR1

6.2B.4.2.4 Inter-band EN-DC including FR2

6.2B.4.2.5 Inter-band EN-DC including both FR1 and FR2

6.2B.4.2 ΔT_IB,c for EN-DC