8.6.4 Logged Radio Link Failure
36.523-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA) and Evolved Packet Core (EPC)Part 1: Protocol conformance specificationRelease 17TSUser Equipment (UE) conformance specification
8.6.4.1 Radio Link Failure logging / Reporting of Intra-frequency measurements
8.6.4.1.1 Test Purpose (TP)
(1)
with { UE in RRC_CONNECTED having performed the intra-frequency measurement and reported that the UE has radio link failure information available }
ensure that {
when { UE receives the UEInformationRequest message containing rlf-ReportReq }
then { UE sends the UEInformationResponse message containing the measurement result for intra-frequency neighbour cell }
}
8.6.4.1.2 Conformance requirements
References: The conformance requirements covered in the present TC are specified in: TS 36.331, clause 5.3.7.4, 5.3.7.5, 5.3.11.3 and 5.6.5.3.
[TS 36.331, clause 5.3.7.4]
If the procedure was initiated due to radio link failure or handover failure, the UE shall:
1> set the reestablishmentCellId in the VarRLF-Report to the global cell identity of the selected cell;
[TS 36.331, clause 5.3.7.5]
The UE shall:
…
1> set the content of RRCConnectionReestablishmentComplete message as follows:
2> if the UE has radio link failure or handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN:
3> include the rlf-InfoAvailable;
…
1> submit the RRCConnectionReestablishmentComplete message to lower layers for transmission, upon which the procedure ends;
[TS 36.331, clause 5.3.11.3]
The UE shall:
1> upon T310 expiry; or
1> upon random access problem indication from MAC while neither T300, T301, T304 nor T311 is running; or
1> upon indication from RLC that the maximum number of retransmissions has been reached:
2> consider radio link failure to be detected;
2> store the following radio link failure information in the VarRLF-Report by setting its fields as follows:
3> clear the information included in VarRLF-Report, if any;
3> set the plmn-Identity to the RPLMN;
3> set the measResultLastServCell to include the RSRP and RSRQ, if available, of the PCell based on measurements collected up to the moment the UE detected radio link failure;
3> set the measResultNeighCells to include the best measured cells, other than the PCell, ordered such that the best cell is listed first, and based on measurements collected up to the moment the UE detected radio link failure, and set its fields as follows;
4> if the UE was configured to perform measurements for one or more EUTRA frequencies, include the measResultListEUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring UTRA frequencies, include the measResultListUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring GERAN frequencies, include the measResultListGERAN;
4> if the UE was configured to perform measurement reporting for one or more neighbouring CDMA2000 frequencies, include the measResultsCDMA2000;
NOTE: The measured quantities are filtered by the L3 filter as configured in the mobility measurement configuration. The measurements are based on the time domain measurement resource restriction, if configured. Blacklisted cells are not required to be reported.
3> if detailed location information is available, set the content of the locationInfo as follows:
4> include the locationCoordinates;
4> include the horizontalVelocity, if available;
3> set the failedPCellId to the global cell identity, if available, and otherwise to the physical cell identity and carrier frequency of the PCell where radio link failure is detected;
3> if an RRCConnectionReconfiguration message including the mobilityControlInfo was received before the connection failure:
4> include previousPCellId and set it to the global cell identity of the PCell where the last RRCConnectionReconfiguration including the mobilityControlInfo message was received;
4> set the timeConnFailure to the elapsed time since reception of the last RRCConnectionReconfiguration message including the mobilityControlInfo;
3> set the connectionFailureType to rlf;
2> if AS security has not been activated:
3> perform the actions upon leaving RRC_CONNECTED as specified in 5.3.12, with release cause ‘other’;
2> else:
3> initiate the connection re-establishment procedure as specified in 5.3.7;
The UE may discard the radio link failure information, i.e. release the UE variable VarRLF-Report 48 hours after the radio link failure is detected.
[TS 36.331, clause 5.6.5.3]
Upon receiving the UEInformationRequest message, the UE shall:
…
1> if rlf-ReportReq is set to true and the UE has radio link failure information or handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN, set the rlf-Report in the UEInformationResponse message to the value of rlf-Report in VarRLF-Report;
1> if the rlf-Report is included in UEInformationResponse:
2> discard the rlf-Report from VarRLF-Report upon successful delivery of the UEInformationResponse message confirmed by lower layers.
…
1> if the logMeasReport is included in the UEInformationResponse:
…
1> else:
2> submit the UEInformationResponse message to lower layers for transmission via SRB1;
8.6.4.1.3 Test description
8.6.4.1.3.1 Pre-test conditions
System Simulator:
– Cell 1 and Cell 2
UE:
None.
Preamble:
– The UE is in state Generic RB Established (state 3) on Cell 1 according to [18].
8.6.4.1.3.2 Test procedure sequence
Table 8.6.4.1.3.2-1 illustrates the downlink power levels and other changing parameters to be applied for the cells at various time instants of the test execution. Row marked "T0" denotes the initial conditions after preamble, while columns marked "T1" and "T2" are to be applied subsequently. The exact instants on which these values shall be applied are described in the texts in this clause.
Table 8.6.4.1.3.2-1: Time instances of cell power level and parameter changes
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Remark |
|
|
T0 |
Cell-specific RS EPRE |
dBm/15kHz |
-85 |
-91 |
The power level values are such that measurement results for Cell 1 (M1) and Cell 2 (M2) satisfy exit condition for event A3 (M2 < M1). |
|
T1 |
Cell-specific RS EPRE |
dBm/15kHz |
-85 |
-79 |
The power level values are such that measurement results for Cell 1 (M1) and Cell 2 (M2) satisfy entry condition for event A3 (M2 > M1). |
|
T2 |
Cell-specific RS EPRE |
dBm/15kHz |
"Off" |
-79 |
Only Cell 2 is available. (NOTE 1) |
|
NOTE 1: Power level “Off” is defined in TS 36.508 Table 6.2.2.1-1. |
|||||
Table 8.6.4.1.3.2-2: Main behaviour
|
St |
Procedure |
Message Sequence |
TP |
Verdict |
|
|
U – S |
Message |
||||
|
1 |
The SS transmits an RRCConnectionReconfiguration message to setup intra frequency measurement on Cell 1. |
<– |
RRCConnectionReconfiguration |
– |
– |
|
2 |
The UE transmits an RRCConnectionReconfigurationComplete message on Cell 1. |
–> |
RRCConnectionReconfigurationComplete |
– |
– |
|
3 |
The SS changes Cell 2 parameters according to the row "T1" in Table 8.6.4.1.3.2-1. |
– |
– |
– |
– |
|
4 |
The UE transmits a MeasurementReport message on Cell 1. |
–> |
MeasurementReport |
– |
– |
|
5 |
The SS changes Cell 1 parameter according to the row "T2" in Table 8.6.4.1.3.2-1. |
– |
– |
– |
– |
|
6 |
The UE transmits an RRCConnectionReestablishmentRequest message on Cell 2. |
–> |
RRCConnectionReestablishmentRequest |
– |
– |
|
7 |
The SS transmits an RRCConnectionReestablishment message on Cell 2. |
<– |
RRCConnectionReestablishment |
– |
– |
|
8 |
The UE transmits an RRCConnectionReestablishmentComplete message on Cell 2. |
–> |
RRCConnectionReestablishmentComplete |
– |
– |
|
9 |
The SS transmits an RRCConnectionReconfiguration message on Cell 2. |
<– |
RRCConnectionReconfiguration |
– |
– |
|
10 |
The UE transmits an RRCConnectionReconfigurationComplete message on Cell 2. |
–> |
RRCConnectionReconfigurationComplete |
– |
– |
|
11 |
The SS transmits a UEInformationRequest message on Cell 2. |
<– |
UEInformationRequest |
– |
– |
|
12 |
Check: Does the UE transmit a UEInformationResponse message on Cell 2? |
–> |
UEInformationResponse |
1 |
P |
|
13 |
Check: Does the test result of generic test procedure in TS 36.508 subclause 6.4.2.3 indicate that the UE is in E-UTRA RRC_CONNECTED state on Cell 2? |
– |
– |
1 |
– |
8.6.4.1.3.3 Specific message contents
Table 8.6.4.1.3.3-0: Conditions for specific message contents
in Tables 8.6.4.1.3.3-2 and 8.6.4.1.3.3-8
|
Condition |
Explanation |
|
Band > 64 |
This condition applies if the band number is bigger than 64. |
Table 8.6.4.1.3.3-1: RRCConnectionReconfiguration (step 1, Table 8.6.4.1.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-8, condition MEAS |
Table 8.6.4.1.3.3-2: MeasConfig (Table 8.6.4.1.3.3-1)
|
Derivation Path: 36.508, Table 4.6.6-1 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MeasConfig ::= SEQUENCE { |
|||
|
measObjectToAddModList SEQUENCE (SIZE (1..maxObjectId)) OF SEQUENCE { |
1 entry |
||
|
measObjectId[1] |
IdMeasObject-f1 |
||
|
measObject[1] |
MeasObjectEUTRA-GENERIC(f1) |
||
|
measObect[1] |
MeasObjectEUTRA-GENERIC(maxEARFCN) |
Band > 64 |
|
|
} |
|||
|
reportConfigToAddModList SEQUENCE (SIZE (1..maxReportConfigId)) OF SEQUENCE { |
1 entry |
||
|
reportConfigId[1] |
IdReportConfig-A3 |
||
|
reportConfig[1] |
ReportConfigEUTRA-A3 |
||
|
} |
|||
|
measIdToAddModListSEQUENCE (SIZE (1..maxMeasId)) OF SEQUENCE { |
|||
|
measId[1] |
1 |
||
|
measObjectId[1] |
IdMeasObject-f1 |
||
|
reportConfigId[1] |
IdReportConfig-A3 |
||
|
} |
|||
|
measObjectToAddModList-v9e0 SEQUENCE (SIZE (1..maxObjectId)) OF SEQUENCE { |
Band > 64 |
||
|
measObjectEUTRA-v9e0[1] SEQUENCE { |
|||
|
carrierFreq-v9e0 |
Same downlink EARFCN as used for f1 |
||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.1.3.3-3: MeasurementReport (step 4, Table 8.6.4.1.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-5 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MeasurementReport ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
measurementReport-r8 SEQUENCE { |
|||
|
measResults SEQUENCE { |
|||
|
measId |
1 |
||
|
measResultPcell SEQUENCE { |
|||
|
rsrpResult |
(0..97) |
||
|
rsrqResult |
(0..34) |
||
|
} |
|||
|
measResultNeighCells CHOICE { |
|||
|
measResultListEUTRA SEQUENCE (SIZE (1..maxCellReport)) OF SEQUENCE { |
1 entry |
||
|
physCellId |
PhysicalCellIdentity of Cell 2 |
||
|
cgi-Info |
Not present |
||
|
measResult SEQUENCE { |
|||
|
rsrpResult |
(0..97) |
||
|
rsrqResult |
(0..34) |
||
|
additionalSI-Info-r9 |
Not present |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
measResultForECID-r9 |
Not present |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.1.3.3-4: RRCConnectionReestablishmentRequest (step 6, Table 8.6.4.1.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-13 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishmentRequest ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
rrcConnectionReestablishmentRequest-r8 SEQUENCE { |
|||
|
ue-Identity SEQUENCE { |
|||
|
c-RNTI |
the value of the C-RNTI of the UE |
||
|
physCellId |
PhysicalCellIdentity of Cell 1 |
||
|
shortMAC-I |
The same value as the 16 least significant bits of the XMAC-I value calculated by SS |
||
|
} |
|||
|
reestablishmentCause |
otherFailure |
||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.1.3.3-5: RRCConnectionReestablishmentComplete (step 8, Table 8.6.4.1.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-11 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishmentComplete ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
rrcConnectionReestablishmentComplete-r8 = SEQUENCE { |
|||
|
nonCriticalExtension SEQUENCE { |
|||
|
rlf-InfoAvailable-r9 |
true |
||
|
nonCriticalExtension |
Not present or any allowed value |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.1.3.3-6: RRCConnectionReconfiguration (step 9, Table 8.6.4.1.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-8 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReconfiguration ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
rrcConnectionReconfiguration-r8 SEQUENCE { |
|||
|
radioResourceConfigDedicated |
RadioResourceConfigDedicated-HO |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.1.3.3-7: UEInformationRequest (step 11, Table 8.6.4.1.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23A |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
UEInformationRequest-r9 ::=SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE { |
|||
|
ueInformationRequest-r9 SEQUENCE { |
|||
|
rlf-ReportReq-r9 |
TRUE |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.1.3.3-8: UEInformationResponse (step 12, Table 8.6.4.1.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23B |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
UEInformationResponse-r9 ::=SEQUENCE { |
||||
|
criticalExtensions CHOICE { |
||||
|
c1 CHOICE { |
||||
|
ueInformationResponse-r9 SEQUENCE { |
||||
|
rlf-Report-r9 SEQUENCE { |
||||
|
measResultLastServCell-r9 SEQUENCE { |
||||
|
rsrpResult-r9 |
(0..97) |
|||
|
rsrqResult-r9 |
Not present or (0..34) |
|||
|
} |
||||
|
measResultNeighCells-r9 SEQUENCE { |
||||
|
measResultListEUTRA-r9 SEQUENCE (SIZE (1..maxFreq)) OF SEQUENCE { |
1 entry |
|||
|
carrierFreq-r9[1] |
Same downlink EARFCN as used for Cell 2 |
|||
|
carrierFreq-r9[1] |
maxEARFCN |
Band > 64 |
||
|
measResultList-r9[1] SEQUENCE (SIZE (1..maxCellReport)) OF SEQUENCE { |
1 entry |
|||
|
physCellId[1] |
Physical cell Identity of Cell 2 |
|||
|
cgi-Info[1] |
Not present |
|||
|
measResult[1] SEQUENCE { |
||||
|
rsrpResult |
(0..97) |
|||
|
rsrqResult |
(0..34) |
|||
|
additionalSI-Info-r9 |
Not present |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
measResultListUTRA-r9 |
Not present |
|||
|
measResultListGERAN-r9 |
Not present |
|||
|
measResultsCDMA2000-r9 |
Not present |
|||
|
} |
||||
|
locationInfo-r10 |
Not present or any allowed value |
|||
|
failedPCellId-r10 CHOICE { |
cellGlobalId-r10 or pci-arfcn-r10 |
If the UE has the global cell identity depending on UE implementation, the UE sets the global cell identity, otherwise the UE sets the physical cell identity and the carrier frequency. |
||
|
cellGlobalId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
} |
||||
|
pci-arfcn-r10 SEQUENCE { |
||||
|
physCellId-r10 |
Physical cell Identity of Cell 1 |
|||
|
carrierFreq-r10 |
Same downlink EARFCN as used for Cell 1 |
|||
|
carrierFreq-r10 |
maxEARFCN |
Band > 64 |
||
|
} |
||||
|
} |
||||
|
reestablishmentCellId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 2 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 2 |
|||
|
} |
||||
|
timeConnFailure-r10 |
Not present |
|||
|
connectionFailureType-r10 |
rlf |
|||
|
previousPCellId-r10 |
Not present |
|||
|
failedPCellId-v1090 SEQUENCE { |
Band > 64 |
|||
|
carrierFreq-v1090 |
Not present or the same downlink EARFCN as used for Cell 1 |
|||
|
} |
||||
|
} |
||||
|
nonCriticalExtension SEQUENCE { |
Band > 64 |
|||
|
lateNonCriticalExtension SEQUENCE { |
||||
|
rlf-Report-v9e0 SEQUENCE { |
||||
|
measResultListEUTRA-v9e0 SEQUENCE (SIZE (1..maxFreq)) OF SEQUENCE { |
||||
|
carrierFreq-v9e0[1] |
Same downlink EARFCN as used for Cell 2 |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
8.6.4.2 Radio Link Failure logging / Reporting of Inter-frequency measurements
8.6.4.2.1 Test Purpose (TP)
(1)
with { UE in RRC_CONNECTED having performed the inter-frequency measurement and reported that the UE has radio link failure information available }
ensure that {
when { UE receives the UEInformationRequest message containing rlf-ReportReq }
then { UE sends the UEInformationResponse message containing the measurement result for inter-frequency neighbour cell }
}
8.6.4.2.2 Conformance requirements
References: The conformance requirements covered in the present TC are specified in: TS 36.331, clause 5.3.7.4, 5.3.7.5, 5.3.11.3 and 5.6.5.3.
[TS 36.331, clause 5.3.7.4]
If the procedure was initiated due to radio link failure or handover failure, the UE shall:
1> set the reestablishmentCellId in the VarRLF-Report to the global cell identity of the selected cell;
[TS 36.331, clause 5.3.7.5]
The UE shall:
…
1> set the content of RRCConnectionReestablishmentComplete message as follows:
2> if the UE has radio link failure or handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN:
3> include the rlf-InfoAvailable;
…
1> submit the RRCConnectionReestablishmentComplete message to lower layers for transmission, upon which the procedure ends;
[TS 36.331, clause 5.3.11.3]
The UE shall:
1> upon T310 expiry; or
1> upon random access problem indication from MAC while neither T300, T301, T304 nor T311 is running; or
1> upon indication from RLC that the maximum number of retransmissions has been reached:
2> consider radio link failure to be detected;
2> store the following radio link failure information in the VarRLF-Report by setting its fields as follows:
3> clear the information included in VarRLF-Report, if any;
3> set the plmn-Identity to the RPLMN;
3> set the measResultLastServCell to include the RSRP and RSRQ, if available, of the PCell based on measurements collected up to the moment the UE detected radio link failure;
3> set the measResultNeighCells to include the best measured cells, other than the PCell, ordered such that the best cell is listed first, and based on measurements collected up to the moment the UE detected radio link failure, and set its fields as follows;
4> if the UE was configured to perform measurements for one or more EUTRA frequencies, include the measResultListEUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring UTRA frequencies, include the measResultListUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring GERAN frequencies, include the measResultListGERAN;
4> if the UE was configured to perform measurement reporting for one or more neighbouring CDMA2000 frequencies, include the measResultsCDMA2000;
NOTE: The measured quantities are filtered by the L3 filter as configured in the mobility measurement configuration. The measurements are based on the time domain measurement resource restriction, if configured. Blacklisted cells are not required to be reported.
3> if detailed location information is available, set the content of the locationInfo as follows:
4> include the locationCoordinates;
4> include the horizontalVelocity, if available;
3> set the failedPCellId to the global cell identity, if available, and otherwise to the physical cell identity and carrier frequency of the PCell where radio link failure is detected;
3> if an RRCConnectionReconfiguration message including the mobilityControlInfo was received before the connection failure:
4> include previousPCellId and set it to the global cell identity of the PCell where the last RRCConnectionReconfiguration including the mobilityControlInfo message was received;
4> set the timeConnFailure to the elapsed time since reception of the last RRCConnectionReconfiguration message including the mobilityControlInfo;
3> set the connectionFailureType to rlf;
2> if AS security has not been activated:
3> perform the actions upon leaving RRC_CONNECTED as specified in 5.3.12, with release cause ‘other’;
2> else:
3> initiate the connection re-establishment procedure as specified in 5.3.7;
The UE may discard the radio link failure information, i.e. release the UE variable VarRLF-Report 48 hours after the radio link failure is detected.
[TS 36.331, clause 5.6.5.3]
Upon receiving the UEInformationRequest message, the UE shall:
…
1> if rlf-ReportReq is set to true and the UE has radio link failure information or handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN, set the rlf-Report in the UEInformationResponse message to the value of rlf-Report in VarRLF-Report;
1> if the rlf-Report is included in UEInformationResponse:
2> discard the rlf-Report from VarRLF-Report upon successful delivery of the UEInformationResponse message confirmed by lower layers.
…
1> if the logMeasReport is included in the UEInformationResponse:
…
1> else:
2> submit the UEInformationResponse message to lower layers for transmission via SRB1;
8.6.4.2.3 Test description
8.6.4.2.3.1 Pre-test conditions
System Simulator:
– Cell 1 and Cell 3
– System information combination 3 as defined in TS 36.508 [18] clause 4.4.3.1 is used in E-UTRA cells.
UE:
None.
Preamble:
– The UE is in state Generic RB Established (state 3) on Cell 1 according to [18].
8.6.4.2.3.2 Test procedure sequence
Table 8.6.4.2.3.2-1 illustrates the downlink power levels and other changing parameters to be applied for the cells at various time instants of the test execution. Row marked "T0" denotes the initial conditions after preamble, while columns marked "T1" and "T2" are to be applied subsequently. The exact instants on which these values shall be applied are described in the texts in this clause.
Table 8.6.4.2.3.2-1: Time instances of cell power level and parameter changes
|
Parameter |
Unit |
Cell 1 |
Cell 3 |
Remark |
|
|
T0 |
Cell-specific RS EPRE |
dBm/15kHz |
-85 |
-97 |
The power level values are such that measurement results for Cell 1 (M1) and Cell 3 (M3) satisfy exit condition for event A3 (M3 < M1). |
|
T1 |
Cell-specific RS EPRE |
dBm/15kHz |
-85 |
-73 |
The power level values are such that measurement results for Cell 1 (M1) and Cell 3 (M3) satisfy entry condition for event A3 (M3 > M1). |
|
T2 |
Cell-specific RS EPRE |
dBm/15kHz |
"Off" |
-73 |
Only Cell 3 is available. (NOTE 1) |
|
NOTE 1: Power level “Off” is defined in TS 36.508 Table 6.2.2.1-1. |
|||||
Table 8.6.4.2.3.2-2: Main behaviour
|
St |
Procedure |
Message Sequence |
TP |
Verdict |
|
|
U – S |
Message |
||||
|
1 |
The SS transmits an RRCConnectionReconfiguration message to setup inter-frequency measurement on Cell 1. |
<– |
RRCConnectionReconfiguration |
– |
– |
|
2 |
The UE transmits an RRCConnectionReconfigurationComplete message on Cell 1. |
–> |
RRCConnectionReconfigurationComplete |
– |
– |
|
3 |
The SS changes Cell 3 parameters according to the row "T1" in Table 8.6.4.2.3.2-1. |
– |
– |
– |
– |
|
4 |
The UE transmits a MeasurementReport message on Cell 1. |
–> |
MeasurementReport |
– |
– |
|
5 |
The SS changes Cell 1 parameter according to the row "T2" in Table 8.6.4.2.3.2-1. |
– |
– |
– |
– |
|
6 |
The UE transmits an RRCConnectionReestablishmentRequest message on Cell 3. |
–> |
RRCConnectionReestablishmentRequest |
– |
– |
|
7 |
The SS transmits an RRCConnectionReestablishment message on Cell 3. |
<– |
RRCConnectionReestablishment |
– |
– |
|
8 |
The UE transmits an RRCConnectionReestablishmentComplete message on Cell 3. |
–> |
RRCConnectionReestablishmentComplete |
– |
– |
|
9 |
The SS transmits an RRCConnectionReconfiguration message on Cell 3. |
<– |
RRCConnectionReconfiguration |
– |
– |
|
10 |
The UE transmits an RRCConnectionReconfigurationComplete message on Cell 3. |
–> |
RRCConnectionReconfigurationComplete |
– |
– |
|
11 |
The SS transmits a UEInformationRequest message on Cell 3. |
<– |
UEInformationRequest |
– |
– |
|
12 |
Check: Does the UE transmit a UEInformationResponse message on Cell 3? |
–> |
UEInformationResponse |
1 |
P |
|
13 |
Check: Does the test result of generic test procedure in TS 36.508 subclause 6.4.2.3 indicate that the UE is in E-UTRA RRC_CONNECTED state on Cell 3? |
– |
– |
1 |
– |
8.6.4.2.3.3 Specific message contents
Table 8.6.4.2.3.3-0: Conditions for specific message contents
in Tables 8.6.4.2.3.3-2 and 8.6.4.2.3.3-8
|
Condition |
Explanation |
|
Band > 64 |
This condition applies if the band number is bigger than 64. |
Table 8.6.4.2.3.3-1: RRCConnectionReconfiguration (step 1, Table 8.6.4.2.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-8, condition MEAS |
Table 8.6.4.2.3.3-2: MeasConfig (Table 8.6.4.2.3.3-1)
|
Derivation Path: 36.508, Table 4.6.6-1, condition INTER-FREQ |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MeasConfig ::= SEQUENCE { |
|||
|
measObjectToAddModList SEQUENCE (SIZE (1..maxObjectId)) OF SEQUENCE { |
2 entries |
||
|
measObjectId[1] |
IdMeasObject-f1 |
||
|
measObject[1] |
MeasObjectEUTRA-GENERIC(f1) |
||
|
measObject[1] |
MeasObjectEUTRA-GENERIC(maxEARFCN) |
Band > 64 |
|
|
measObjectId[2] |
IdMeasObject-f2 |
||
|
measObject[2] |
MeasObjectEUTRA-GENERIC(f2) |
||
|
measObject[2] |
MeasObjectEUTRA-GENERIC(maxEARFCN) |
Band > 64 |
|
|
} |
|||
|
reportConfigToAddModList SEQUENCE (SIZE (1..maxReportConfigId)) OF SEQUENCE { |
1 entry |
||
|
reportConfigId[1] |
IdReportConfig-A3 |
||
|
reportConfig[1] |
ReportConfigEUTRA-A3 |
||
|
} |
|||
|
measIdToAddModListSEQUENCE (SIZE (1..maxMeasId)) OF SEQUENCE { |
|||
|
measId[1] |
1 |
||
|
measObjectId[1] |
IdMeasObject-f2 |
||
|
reportConfigId[1] |
IdReportConfig-A3 |
||
|
} |
|||
|
measObjectToAddModList-v9e0 SEQUENCE (SIZE (1..maxObjectId)) OF SEQUENCE { |
Band > 64 |
||
|
measObjectEUTRA-v9e0[1] SEQUENCE { |
|||
|
carrierFreq-v9e0 |
Same downlink EARFCN as used for f1 |
||
|
} |
|||
|
measObjectEUTRA-v9e0[2] SEQUENCE { |
|||
|
carrierFreq-v9e0 |
Same downlink EARFCN as used for f2 |
||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.2.3.3-3: MeasurementReport (step 4, Table 8.6.4.2.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-5 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MeasurementReport ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
measurementReport-r8 SEQUENCE { |
|||
|
measResults SEQUENCE { |
|||
|
measId |
1 |
||
|
measResultPcell SEQUENCE { |
|||
|
rsrpResult |
(0..97) |
||
|
rsrqResult |
(0..34) |
||
|
} |
|||
|
measResultNeighCells CHOICE { |
|||
|
measResultListEUTRA SEQUENCE (SIZE (1..maxCellReport)) OF SEQUENCE { |
1 entry |
||
|
physCellId |
PhysicalCellIdentity of Cell 3 |
||
|
cgi-Info |
Not present |
||
|
measResult SEQUENCE { |
|||
|
rsrpResult |
(0..97) |
||
|
rsrqResult |
(0..34) |
||
|
additionalSI-Info-r9 |
Not present |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
measResultForECID-r9 |
Not present |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.2.3.3-4: RRCConnectionReestablishmentRequest (step 6, Table 8.6.4.2.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-13 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishmentRequest ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
rrcConnectionReestablishmentRequest-r8 SEQUENCE { |
|||
|
ue-Identity SEQUENCE { |
|||
|
c-RNTI |
the value of the C-RNTI of the UE |
||
|
physCellId |
PhysicalCellIdentity of Cell 1 |
||
|
shortMAC-I |
The same value as the 16 least significant bits of the XMAC-I value calculated by SS |
||
|
} |
|||
|
reestablishmentCause |
otherFailure |
||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.2.3.3-5: RRCConnectionReestablishmentComplete (step 8, Table 8.6.4.2.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-11 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishmentComplete ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
rrcConnectionReestablishmentComplete-r8 = SEQUENCE { |
|||
|
nonCriticalExtension SEQUENCE { |
|||
|
rlf-InfoAvailable-r9 |
true |
||
|
nonCriticalExtension |
Not present or any allowed value |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.2.3.3-6: RRCConnectionReconfiguration (step 9, Table 8.6.4.2.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-8 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReconfiguration ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
rrcConnectionReconfiguration-r8 SEQUENCE { |
|||
|
radioResourceConfigDedicated |
RadioResourceConfigDedicated-HO |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.2.3.3-7: UEInformationRequest (step 11, Table 8.6.4.2.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23A |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
UEInformationRequest-r9 ::=SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE { |
|||
|
ueInformationRequest-r9 SEQUENCE { |
|||
|
rlf-ReportReq-r9 |
TRUE |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.2.3.3-8: UEInformationResponse (step 12, Table 8.6.4.2.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23B |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
UEInformationResponse-r9 ::=SEQUENCE { |
||||
|
criticalExtensions CHOICE { |
||||
|
c1 CHOICE { |
||||
|
ueInformationResponse-r9 SEQUENCE { |
||||
|
rlf-Report-r9 SEQUENCE { |
||||
|
measResultLastServCell-r9 SEQUENCE { |
||||
|
rsrpResult-r9 |
(0..97) |
|||
|
rsrqResult-r9 |
Not present or (0..34) |
|||
|
} |
||||
|
measResultNeighCells-r9 SEQUENCE { |
||||
|
measResultListEUTRA-r9 SEQUENCE (SIZE (1..maxFreq)) OF SEQUENCE { |
1 entry |
|||
|
carrierFreq-r9[1] |
Same downlink EARFCN as used for Cell 3 |
|||
|
carrierFreq-r9[1] |
maxEARFCN |
Band > 64 |
||
|
measResultList-r9[1] SEQUENCE (SIZE (1..maxCellReport)) OF SEQUENCE { |
1 entry |
|||
|
physCellId[1] |
PhysicalCellIdentity of Cell 3 |
|||
|
cgi-Info[1] |
Not present |
|||
|
measResult[1] SEQUENCE { |
||||
|
rsrpResult |
(0..97) |
|||
|
rsrqResult |
(0..34) |
|||
|
additionalSI-Info-r9 |
Not present |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
measResultListUTRA-r9 |
Not present |
|||
|
measResultListGERAN-r9 |
Not present |
|||
|
measResultsCDMA2000-r9 |
Not present |
|||
|
} |
||||
|
locationInfo-r10 |
Not present or any allowed value |
|||
|
failedPCellId-r10 CHOICE { |
cellGlobalId-r10 or pci-arfcn-r10 |
If the UE has the global cell identity depending on UE implementation, the UE sets the global cell identity, otherwise the UE sets the physical cell identity and the carrier frequency. |
||
|
cellGlobalId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
} |
||||
|
pci-arfcn-r10 SEQUENCE { |
||||
|
physCellId-r10 |
PhysicalCellIdentity of Cell 1 |
|||
|
carrierFreq-r10 |
Same downlink EARFCN as used for Cell 1 |
|||
|
carrierFreq-r10 |
maxEARFCN |
Band > 64 |
||
|
} |
||||
|
} |
||||
|
reestablishmentCellId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 3 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 3 |
|||
|
} |
||||
|
timeConnFailure-r10 |
Not present |
|||
|
connectionFailureType-r10 |
rlf |
|||
|
previousPCellId-r10 |
Not present |
|||
|
failedPCellId-v1090 SEQUENCE { |
Band > 64 |
|||
|
carrierFreq-v1090 |
Not present or the same downlink EARFCN as used for Cell 1 |
|||
|
} |
||||
|
} |
||||
|
nonCriticalExtension SEQUENCE { |
Band > 64 |
|||
|
lateNonCriticalExtension SEQUENCE { |
||||
|
rlf-Report-v9e0 SEQUENCE { |
||||
|
measResultListEUTRA-v9e0 SEQUENCE (SIZE (1..maxFreq)) OF SEQUENCE { |
||||
|
carrierFreq-v9e0[1] |
Same downlink EARFCN as used for Cell 3 |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
8.6.4.3 Radio Link Failure logging / Reporting at RRC connection establishment and reestablishment
8.6.4.3.1 Test Purpose (TP)
(1)
with { UE in RRC_CONNECTED state detecting radio link failure }
ensure that {
when { T301 expires after UE having sent an RRCConnectionReestablishmentRequest message, the UE has radio link failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN }
then { UE sends the RRCConnectionSetupComplete message with rlf-InfoAvailable included when UE performs TAU procedure }
}
(2)
with { UE in RRC_CONNECTED state detecting radio link failure }
ensure that {
when { UE has radio link failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN }
then { UE sends the RRCConnectionReestablishmentComplete message with rlf-InfoAvailable included
}
}
(3)
with { UE in RRC_CONNECTED state with the radio link failure information available and plmn-Identity stored in VarRLF-Report is equal to the RPLMN }
ensure that {
when { UE receives the UEInformationRequest message with rlf-ReportReq set to true }
then { UE sends the UEInformationResponse message with rlf-Report included }
}
(4)
with { UE in RRC_CONNECTED state with the radio link failure information available and plmn-Identity stored in VarRLF-Report is equal to the RPLMN }
ensure that {
when { UE receives the UEInformationRequest message containing rlf-ReportReq }
then { UE sends the UEInformationResponse message with eestablishmentCellId set to the global cell identity of the selected cell }
}
(5)
with { UE in RRC_CONNECTED state with successful delivery of the UEInformationResponse message confirmed by lower layer }
ensure that {
when { UE receives the UEInformationRequest message containing rlf-ReportReq }
then { UE sends the UEInformationResponse message without rlf-Report included }
}
8.6.4.3.2 Conformance requirements
References: The conformance requirements covered in the present TC are specified in: TS 36.331, clause 5.3.3.4, 5.3.7.5, 5.3.11.3, 5.3.7.4 and 5.6.5.3.
[TS 36.331, clause 5.3.3.4 (TP1)]
The UE shall:
…
1> set the content of RRCConnectionSetupComplete message as follows:
…
2> set the dedicatedInfoNAS to include the information received from upper layers;
2> if the UE has radio link failure or handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN:
3> include rlf-InfoAvailable;
…
2> submit the RRCConnectionSetupComplete message to lower layers for transmission, upon which the procedure ends;
[TS 36.331, clause 5.3.7.5 (TP2)]
The UE shall:
…
1> set the content of RRCConnectionReestablishmentComplete message as follows:
2> if the UE has radio link failure or handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN:
3> include the rlf-InfoAvailable;
…
1> submit the RRCConnectionReestablishmentComplete message to lower layers for transmission, upon which the procedure ends;
[TS 36.331, clause 5.3.11.3 (TP1, TP2)]
The UE shall:
1> upon T310 expiry; or
1> upon random access problem indication from MAC while neither T300, T301, T304 nor T311 is running; or
1> upon indication from RLC that the maximum number of retransmissions has been reached:
2> consider radio link failure to be detected;
2> store the following radio link failure information in the VarRLF-Report by setting its fields as follows:
3> clear the information included in VarRLF-Report, if any;
3> set the plmn-Identity to the RPLMN;
3> set the measResultLastServCell to include the RSRP and RSRQ, if available, of the PCell based on measurements collected up to the moment the UE detected radio link failure;
3> set the measResultNeighCells to include the best measured cells, other than the PCell, ordered such that the best cell is listed first, and based on measurements collected up to the moment the UE detected radio link failure, and set its fields as follows;
4> if the UE was configured to perform measurements for one or more EUTRA frequencies, include the measResultListEUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring UTRA frequencies, include the measResultListUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring GERAN frequencies, include the measResultListGERAN;
4> if the UE was configured to perform measurement reporting for one or more neighbouring CDMA2000 frequencies, include the measResultsCDMA2000;
NOTE: The measured quantities are filtered by the L3 filter as configured in the mobility measurement configuration. The measurements are based on the time domain measurement resource restriction, if configured. Blacklisted cells are not required to be reported.
3> if detailed location information is available, set the content of the locationInfo as follows:
4> include the locationCoordinates;
4> include the horizontalVelocity, if available;
3> set the failedPCellId to the global cell identity, if available, and otherwise to the physical cell identity and carrier frequency of the PCell where radio link failure is detected;
3> if an RRCConnectionReconfiguration message including the mobilityControlInfo was received before the connection failure:
4> include previousPCellId and set it to the global cell identity of the PCell where the last RRCConnectionReconfiguration including the mobilityControlInfo message was received;
4> set the timeConnFailure to the elapsed time since reception of the last RRCConnectionReconfiguration message including the mobilityControlInfo;
3> set the connectionFailureType to rlf;
2> if AS security has not been activated:
3> perform the actions upon leaving RRC_CONNECTED as specified in 5.3.12, with release cause ‘other’;
2> else:
3> initiate the connection re-establishment procedure as specified in 5.3.7;
The UE may discard the radio link failure information, i.e. release the UE variable VarRLF-Report 48 hours after the radio link failure is detected.
[TS 36.331, clause 5.3.7.4 (TP4)]
If the procedure was initiated due to radio link failure or handover failure, the UE shall:
1> set the reestablishmentCellId in the VarRLF-Report to the global cell identity of the selected cell;
[TS 36.331, clause 5.6.5.3 (TP4,TP5)]
Upon receiving the UEInformationRequest message, the UE shall:
…
1> if rlf-ReportReq is set to true and the UE has radio link failure information or handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN, set the rlf-Report in the UEInformationResponse message to the value of rlf-Report in VarRLF-Report;
1> if the rlf-Report is included in UEInformationResponse:
2> discard the rlf-Report from VarRLF-Report upon successful delivery of the UEInformationResponse message confirmed by lower layers.
…
1> if the logMeasReport is included in the UEInformationResponse:
…
1> else:
2> submit the UEInformationResponse message to lower layers for transmission via SRB1;
8.6.4.3.3 Test description
8.6.4.3.3.1 Pre-test conditions
System Simulator:
– Cell 1, Cell 3 and Cell 6
– System information combination 3 as defined in TS 36.508 [18] clause 4.4.3.1 is used in E-UTRA cells.
UE:
None.
Preamble:
– The UE is in state Generic RB Established (state 3) on Cell 1 according to [18].
8.6.4.3.3.2 Test procedure sequence
Table 8.6.4.3.3.2-1 illustrates the downlink power levels and other changing parameters to be applied for the cells at various time instants of the test execution. Row marked "T0" denotes the initial conditions after preamble, while columns marked "T1" and "T2" are to be applied subsequently. The exact instants on which these values shall be applied are described in the texts in this clause.
Table 8.6.4.3.3.2-1: Time instances of cell power level and parameter changes
|
Parameter |
Unit |
Cell 1 |
Cell 3 |
Cell 6 |
Remark |
|
|
T0 |
Cell-specific RS EPRE |
dBm/15kHz |
-85 |
“Off” |
"Off" |
|
|
T1 |
Cell-specific RS EPRE |
dBm/15kHz |
"Off" |
-85 |
"Off" |
|
|
T2 |
Cell-specific RS EPRE |
dBm/15kHz |
"Off" |
"Off" |
-85 |
|
|
NOTE 1: Power level “Off” is defined in TS 36.508 Table 6.2.2.1-1. |
||||||
Table 8.6.4.3.3.2-2: Main behaviour
|
St |
Procedure |
Message Sequence |
TP |
Verdict |
|
|
U – S |
Message |
||||
|
1 |
The SS changes Cell 1 and Cell 3 parameters according to the row "T1" in Table 8.6.4.3.3.2-1 in order that the radio link quality of Cell 1 is degraded and Cell 3 is suitable for camping. |
– |
– |
– |
– |
|
2 |
The UE transmits an RRCConnectionReestablishmentRequest message on Cell 3. |
–> |
RRCConnectionReestablishmentRequest |
– |
– |
|
3 |
The SS does not respond to any RRCConnectionReestablishmentRequest message and waits for 1s to ensure that T301 expires and the UE goes to RRC_IDLE state on Cell 3. |
||||
|
4 |
The UE transmits an RRCConnectionRequest message on Cell 3 |
–> |
RRC: RRCConnectionRequest |
– |
– |
|
5 |
The SS transmit an RRCConnectionSetup message. |
<– |
RRC: RRCConnectionSetup |
– |
– |
|
6 |
Check: Does the UE transmit an RRCConnectionSetupComplete message to confirm the successful completion of the connection establishment with rlf-InfoAvailable included? |
–> |
RRC: RRCConnectionSetupComplete NAS: TRACKING AREA UPDATE REQUEST |
1 |
P |
|
6A |
The SS transmits a SecurityModeCommand message to activate AS security. |
<– |
RRC: SecurityModeCommand |
– |
– |
|
6B |
The UE transmits a SecurityModeComplete message and establishes the initial security configuration. |
–> |
RRC: SecurityModeComplete |
– |
– |
|
7 |
The SS responds with TRACKING AREA UPDATE ACCEPT message. |
<– |
RRC: DLInformationTransfer NAS: TRACKING AREA UPDATE ACCEPT |
– |
– |
|
8 |
The UE sends a TRACKING AREA UPDATE COMPLETE on Cell 3 to finish the TAU procedure |
–> |
RRC: ULInformationTransfer NAS: TRACKING AREA UPDATE COMPLETE |
– |
– |
|
9 |
The SS changes Cell 3 and Cell 6 parameters according to the row "T2" in Table 8.6.4.3.3.2-1 in order that the radio link quality of Cell 3 is degraded and Cell 6 is suitable for camping. |
– |
– |
– |
– |
|
10 |
The UE transmits an RRCConnectionReestablishmentRequest message on Cell 6. |
–> |
RRCConnectionReestablishmentRequest |
– |
– |
|
11 |
The SS transmits an RRCConnectionReestablishment message on Cell 6. |
<– |
RRCConnectionReestablishment |
– |
– |
|
12 |
Check: Does the UE transmit an RRCConnectionReestablishmentComplete message on Cell 6 with rlf-InfoAvailable included? |
–> |
RRCConnectionReestablishmentComplete |
2 |
P |
|
13 |
The SS transmits an RRCConnectionReconfiguration message to resume existing radio bearer on Cell 6. |
<– |
RRCConnectionReconfiguration |
– |
– |
|
14 |
The UE transmits an RRCConnectionReconfigurationComplete message on Cell 6. |
–> |
RRCConnectionReconfigurationComplete |
– |
– |
|
15 |
The SS transmits a UEInformationRequest message with rlf-ReportReq set to true on Cell 6. |
<– |
UEInformationRequest |
– |
– |
|
16 |
Check: Does the UE transmit a UEInformationResponse message on Cell 6 with rlf-Report included? Check: Does the reestablishmentCellId included in the UEInformationResponse message equal to the global cell identity of Cell 6? |
–> |
UEInformationResponse |
3, 4 |
P |
|
17 |
The SS transmits a UEInformationRequest message with rlf-ReportReq set to true on Cell 6. |
<– |
UEInformationRequest |
– |
– |
|
18 |
Check: Does the UE transmit a UEInformationResponse message on Cell 6 without rlf-Report included? |
–> |
UEInformationResponse |
5 |
P |
|
19 |
Check: Does the test result of generic test procedure in TS 36.508 subclause 6.4.2.3 indicate that the UE is in E-UTRA RRC_CONNECTED state on Cell 6? |
– |
– |
1 |
– |
|
– |
At the end of this test procedure sequence, the UE is in end state E-UTRA connected (E2_T3440) according to TS 36.508. |
– |
– |
– |
– |
8.6.4.3.3.3 Specific message contents
Table 8.6.4.3.3.3-1: RRCConnectionReestablishmentRequest (step 2, Table 8.6.4.3.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-13 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishmentRequest ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
rrcConnectionReestablishmentRequest-r8 SEQUENCE { |
|||
|
ue-Identity SEQUENCE { |
|||
|
c-RNTI |
the value of the C-RNTI of the UE |
||
|
physCellId |
PhysicalCellIdentity of Cell 1 |
||
|
shortMAC-I |
The same value as the 16 least significant bits of the XMAC-I value calculated by SS |
||
|
} |
|||
|
reestablishmentCause |
otherFailure |
||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.3.3.3-2: RRCConnectionSetupComplete (step 6, Table 8.6.4.3.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-18 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
RRCConnectionSetupComplete ::= SEQUENCE { |
||||
|
rrc-TransactionIdentifier |
RRC-TransactionIdentifier-UL |
|||
|
criticalExtensions CHOICE { |
||||
|
c1 CHOICE { |
||||
|
rrcConnectionSetupComplete-r8 SEQUENCE { |
||||
|
nonCriticalExtension SEQUENCE { |
||||
|
lateNonCriticalExtension |
||||
|
nonCriticalExtension SEQUENCE { |
||||
|
rlf-InfoAvailable-r10 |
true |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
Table 8.6.4.3.3.3-3: RRCConnectionReestablishmentRequest (step 10, Table 8.6.4.3.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-13 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishmentRequest ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
rrcConnectionReestablishmentRequest-r8 SEQUENCE { |
|||
|
ue-Identity SEQUENCE { |
|||
|
c-RNTI |
the value of the C-RNTI of the UE |
||
|
physCellId |
PhysicalCellIdentity of Cell 3 |
||
|
shortMAC-I |
The same value as the 16 least significant bits of the XMAC-I value calculated by SS |
||
|
} |
|||
|
reestablishmentCause |
otherFailure |
||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.3.3.3-4: RRCConnectionReestablishmentComplete (step 12, Table 8.6.4.3.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-11 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishmentComplete ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
rrcConnectionReestablishmentComplete-r8 = SEQUENCE { |
|||
|
nonCriticalExtension SEQUENCE { |
|||
|
rlf-InfoAvailable-r9 |
true |
||
|
nonCriticalExtension |
Not present or any allowed value |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.3.3.3-5: RRCConnectionReconfiguration (step 13, Table 8.6.4.3.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-8 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReconfiguration ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
rrcConnectionReconfiguration-r8 SEQUENCE { |
|||
|
radioResourceConfigDedicated |
RadioResourceConfigDedicated-HO |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.3.3.3-6: UEInformationRequest (steps 15 and 17, Table 8.6.4.3.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23A |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
UEInformationRequest-r9 ::=SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE { |
|||
|
ueInformationRequest-r9 SEQUENCE { |
|||
|
rlf-ReportReq-r9 |
TRUE |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.3.3.3-7: UEInformationResponse (step 16, Table 8.6.4.3.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23B |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
UEInformationResponse-r9 ::=SEQUENCE { |
||||
|
criticalExtensions CHOICE { |
||||
|
c1 CHOICE { |
||||
|
ueInformationResponse-r9 SEQUENCE { |
||||
|
rlf-Report-r9 SEQUENCE { |
||||
|
measResultLastServCell-r9 SEQUENCE { |
Cell 3 |
|||
|
rsrpResult-r9 |
(0..97) |
|||
|
rsrqResult-r9 |
Not present or (0..34) |
|||
|
} |
||||
|
locationInfo-r10 |
Not present or any allowed value |
|||
|
failedPCellId-r10 CHOICE { |
cellGlobalId-r10 or pci-arfcn-r10 |
If the UE has the global cell identity depending on UE implementation, the UE sets the global cell identity, otherwise the UE sets the physical cell identity and the carrier frequency. |
||
|
cellGlobalId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 3 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 3 |
|||
|
} |
||||
|
pci-arfcn-r10 SEQUENCE { |
||||
|
physCellId-r10 |
PhysicalCellIdentity of Cell 3 |
|||
|
carrierFreq-r10 |
Same downlink EARFCN as used for Cell 3 |
|||
|
carrierFreq-r10 |
maxEARFCN |
Band > 64 |
||
|
} |
||||
|
} |
||||
|
reestablishmentCellId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 6 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 6 |
|||
|
} |
||||
|
timeConnFailure-r10 |
Not present |
|||
|
connectionFailureType-r10 |
rlf |
|||
|
failedPCellId-v1090 SEQUENCE { |
Band > 64 |
|||
|
carrierFreq-v1090 |
Not present or the same downlink EARFCN as used for Cell 3 |
|||
|
} |
||||
|
previousPCellId-r10 |
Not present |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
Condition |
Explanation |
|
Band > 64 |
This condition applies if the band number is bigger than 64. |
Table 8.6.4.3.3.3-8: UEInformationResponse (step 18, Table 8.6.4.3.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23B |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
UEInformationResponse-r9 ::=SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE { |
|||
|
ueInformationResponse-r9 SEQUENCE { |
|||
|
rlf-Report-r9 |
Not present |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
8.6.4.4 Radio Link Failure logging / Reporting at E-UTRA handover
8.6.4.4.1 Test Purpose (TP)
(1)
with { UE in RRC_CONNECTED state with T304 expiry and handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN for Rel-10 UE, or the RPLMN is included in plmn-IdentityList stored in VarRLF-Report for Rel-11 and onwards UE }
ensure that {
when { UE receives the RRCConnectionReestablishment message and completes the RRC Connection Reestablishment successfully }
then { UE sends the RRCConnectionReestablishmentComplete message including rlf-InfoAvailable }
(2)
with { UE in RRC_CONNECTED state with handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN for Rel-10 UE, or the RPLMN is included in plmn-IdentityList stored in VarRLF-Report for Rel-11 and onwards UE }
ensure that {
when { UE receives RRCConnectionReconfiguration message includes the mobilityControlInfo and the UE is able to comply with the configuration included in this message }
then { UE sends the RRCConnectionReconfigurationComplete message with rlf-InfoAvailable included }
}
(3)
with { UE in RRC_CONNECTED state with the handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN for Rel-10 UE, or the RPLMN is included in plmn-IdentityList stored in VarRLF-Report for Rel-11 and onwards UE }
ensure that {
when { UE receives the UEInformationRequest message with rlf-ReportReq set to true }
then { UE sends the UEInformationResponse message with rlf-Report included }
}
(4)
with { UE in RRC_CONNECTED state with the handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN for Rel-10 UE, or the RPLMN is included in plmn-IdentityList stored in VarRLF-Report for Rel-11 and onwards UE }
ensure that {
when { UE receives the UEInformationRequest message with rlf-ReportReq set to true }
then { UE sends the UEInformationResponse message with eestablishmentCellId set to the global cell identity of the selected cell }
}
(5)
with { Rel-10 UE in RRC_CONNECTED state with the handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is not equal to the RPLMN }
ensure that {
when { UE receives the UEInformationRequest message with rlf-ReportReq set to true }
then { UE sends the UEInformationResponse message without rlf-Report included }
}
8.6.4.4.2 Conformance requirements
References: The conformance requirements covered in the present TC are specified in: TS 36.331, clause 5.3.5.4, 5.3.5.6, 5.3.7.4 and 5.6.5.3. Unless otherwise stated these are Rel-10 requirements.
[TS 36.331, clause 5.3.5.4]
If the RRCConnectionReconfiguration message includes the mobilityControlInfo and the UE is able to comply with the configuration included in this message, the UE shall:
…
1> set the content of RRCConnectionReconfigurationComplete message as follows:
2> if the UE has radio link failure or handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN:
3> include rlf-InfoAvailable;
2> if the UE has logged measurements available for E-UTRA and plmn-Identity stored in VarLogMeasReport is equal to the RPLMN:
3> include the logMeasAvailable;
1> submit the RRCConnectionReconfigurationComplete message to lower layers for transmission;
[TS 36.331, clause 5.3.5.6]
[Rel-10]
The UE shall:
1> if T304 expires (handover failure):
NOTE 1: Following T304 expiry any dedicated preamble, if provided within the rach-ConfigDedicated, is not available for use by the UE anymore.
2> revert back to the configuration used in the source PCell, excluding the configuration configured by the physicalConfigDedicated, the mac-MainConfig and the sps-Config;
2> store the following handover failure information in VarRLF-Report by setting its fields as follows:
3> clear the information included in VarRLF-Report, if any;
3> set the plmn-Identity to the RPLMN;
3> set the measResultLastServCell to include the RSRP and RSRQ, if available, of the PCell based on measurements collected up to the moment the UE detected handover failure;
3> set the measResultNeighCells to include the best measured cells, other than the PCell, ordered such that the best cell is listed first, and based on measurements collected up to the moment the UE detected handover failure, and set its fields as follows;
4> if the UE was configured to perform measurements for one or more EUTRA frequencies, include the measResultListEUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring UTRA frequencies, include the measResultListUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring GERAN frequencies, include the measResultListGERAN;
4> if the UE was configured to perform measurement reporting for one or more neighbouring CDMA2000 frequencies, include the measResultsCDMA2000;
NOTE 2: The measured quantities are filtered by the L3 filter as configured in the mobility measurement configuration. The measurements are based on the time domain measurement resource restriction, if configured. Blacklisted cells are not required to be reported.
3> if detailed location information is available, set the content of the locationInfo as follows:
4> include the locationCoordinates;
4> include the horizontalVelocity, if available;
3> set the failedPCellId to the global cell identity, if available, and otherwise to the physical cell identity and carrier frequency of the target PCell of the failed handover;
3> include previousPCellId and set it to the global cell identity of the PCell where the last RRCConnectionReconfiguration message including mobilityControlInfo was received;
3> set the timeConnFailure to the elapsed time since reception of the last RRCConnectionReconfiguration message including the mobilityControlInfo;
3> set the connectionFailureType to ‘hof‘;
2> initiate the connection re-establishment procedure as specified in 5.3.7, upon which the RRC connection reconfiguration procedure ends;
The UE may discard the handover failure information, i.e. release the UE variable VarRLF-Report, 48 hours after the failure is detected, upon power off or upon detach.
NOTE 3: E-UTRAN may retrieve the handover failure information using the UE information procedure with rlf-ReportReq set to true, as specified in 5.6.5.3.
[Rel-11]
The UE shall:
1> if T304 expires (handover failure):
NOTE 1: Following T304 expiry any dedicated preamble, if provided within the rach-ConfigDedicated, is not available for use by the UE anymore.
2> revert back to the configuration used in the source PCell, excluding the configuration configured by the physicalConfigDedicated, the mac-MainConfig and the sps-Config;
2> store the following handover failure information in VarRLF-Report by setting its fields as follows:
3> clear the information included in VarRLF-Report, if any;
3> set the plmn-IdentityList to include the list of EPLMNs stored by the UE (i.e. includes the RPLMN);
…
[TS 36.331, clause 5.3.7.4]
If the procedure was initiated due to radio link failure or handover failure, the UE shall:
1> set the reestablishmentCellId in the VarRLF-Report to the global cell identity of the selected cell;
The UE shall set the contents of RRCConnectionReestablishmentRequest message as follows:
…
1> set the reestablishmentCause as follows:
…
2> else if the re-establishment procedure was initiated due to handover failure as specified in 5.3.5.6 (intra-LTE handover failure) or 5.4.3.5 (inter-RAT mobility from EUTRA failure):
3> set the reestablishmentCause to the value handoverFailure;
2> else:
3> set the reestablishmentCause to the value otherFailure;
The UE shall submit the RRCConnectionReestablishmentRequest message to lower layers for transmission.
[TS 36.331, clause 5.6.5.3]
[Rel-10]
Upon receiving the UEInformationRequest message, the UE shall:
…
1> if rlf-ReportReq is set to true and the UE has radio link failure information or handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN, set the rlf-Report in the UEInformationResponse message to the value of rlf-Report in VarRLF-Report;
1> if the rlf-Report is included in UEInformationResponse:
2> discard the rlf-Report from VarRLF-Report upon successful delivery of the UEInformationResponse message confirmed by lower layers.
…
1> if the logMeasReport is included in the UEInformationResponse:
…
1> else:
2> submit the UEInformationResponse message to lower layers for transmission via SRB1;
[Rel-11]
Upon receiving the UEInformationRequest message, the UE shall:
…
1> if rlf-ReportReq is set to true and the UE has radio link failure information or handover failure information available in VarRLF-Report and if the RPLMN is included in plmn-IdentityList stored in VarRLF-Report:
2> set timeSinceFailure in VarRLF-Report to the time that elapsed since the last radio link or handover failure in E-UTRA;
2> set the rlf-Report in the UEInformationResponse message to the value of rlf-Report in VarRLF-Report;
2> discard the rlf-Report from VarRLF-Report upon successful delivery of the UEInformationResponse message confirmed by lower layers;
…
1> if the logMeasReport is included in the UEInformationResponse:
2> submit the UEInformationResponse message to lower layers for transmission via SRB2;
2> discard the logged measurement entries included in the logMeasInfoList from VarLogMeasReport upon successful delivery of the UEInformationResponse message confirmed by lower layers;
1> else:
2> submit the UEInformationResponse message to lower layers for transmission via SRB1;
8.6.4.4.3 Test description
8.6.4.4.3.1 Pre-test conditions
System Simulator:
– Cell 1, Cell 4 and Cell 12
– Each cell has only a single PLMN identity. The PLMNs are identified in the test by the identifiers in Table 8.6.4.4.3.1-1.
Table 8.6.4.4.3.1-1: PLMN identifiers
|
Cell |
PLMN name |
|
1,4 |
PLMN1 |
|
12 |
PLMN2 |
UE:
None.
Preamble:
– The UE is registered on PLMN1 (Cell 1) using the procedure described in TS 36.508[18] clause 4.5.2.3 except that the ATTACH ACCEPT message indicates PLMN2 in the Equivalent PLMN list as described in Table 8.6.4.4.3.3-19
– The UE is in state Generic RB Established (state 3) on Cell 1 according to [18].
8.6.4.4.3.2 Test procedure sequence
Table 8.6.4.4.3.2-1 illustrates the downlink power levels and other changing parameters to be applied for the cells at various time instants of the test execution. Row marked "T0" denotes the initial conditions after preamble, while columns marked "T1", "T2", "T3", "T4" and "T5" are to be applied subsequently. The exact instants on which these values shall be applied are described in the texts in this clause.
Table 8.6.4.4.3.2-1: Time instances of cell power level and parameter changes
|
Parameter |
Unit |
Cell 1 |
Cell 4 |
Cell 12 |
Remark |
|
|
T0 |
Cell-specific RS EPRE |
dBm/15kHz |
-85 |
Off |
-97 |
The power level values are such that measurement results for Cell 1 (M1) and Cell 12 (M12) satisfy exit condition for event A3 (M12< M1). |
|
T1 |
Cell-specific RS EPRE |
dBm/15kHz |
-85 |
Off |
-73 |
The power level values are such that measurement results for Cell 1 (M1) and Cell 12 (M12) satisfy entry condition for event A3 (M12 > M1). |
|
T2 |
Cell-specific RS EPRE |
dBm/15kHz |
-85 |
Off |
Off |
The power level values are assigned to satisfy SrxlevCell 12 < 0 such that selecting Cell 1 is guaranteed (NOTE 1). |
|
T3 |
Cell-specific RS EPRE |
dBm/15kHz |
-85 |
-79 |
Off |
The power level values are such that measurement results for Cell 1 (M1) and Cell 4 (M4) satisfy entry condition for event A3 (M4 > M1). |
|
T4 |
Cell-specific RS EPRE |
dBm/15kHz |
Off |
-85 |
-73 |
The power level values are such that measurement results for Cell 4 (M4) and Cell 12 (M12) satisfy entry condition for event A3 (M12> M4). (NOTE 1). |
|
T5 |
Cell-specific RS EPRE |
dBm/15kHz |
Off |
Off |
-73 |
The power level values are assigned to satisfy SrxlevCell 4 < 0 such that selecting Cell 12 is guaranteed (NOTE 1). |
|
NOTE 1: Power level “Off” is defined in TS 36.508 Table 6.2.2.1-1. |
||||||
Table 8.6.4.4.3.2-2: Main behaviour
|
St |
Procedure |
Message Sequence |
TP |
Verdict |
|
|
U – S |
Message |
||||
|
1 |
The SS transmits an RRCConnectionReconfiguration message to setup intra and inter frequency measurement on Cell 1. |
<– |
RRCConnectionReconfiguration |
– |
– |
|
2 |
The UE transmits an RRCConnectionReconfigurationComplete message on Cell 1. |
–> |
RRCConnectionReconfigurationComplete |
– |
– |
|
3 |
The SS changes Cell 12 parameter according to the row "T1" in table 8.6.4.4.3.2-1. |
– |
– |
– |
– |
|
4 |
The UE transmits a MeasurementReport message on Cell 1 to report event A3 with the measured RSRP, RSRQ value for Cell 12. |
–> |
MeasurementReport |
– |
– |
|
5 |
The SS transmits an RRCConnectionReconfiguration message on Cell 1 to order the UE to perform inter frequency handover to Cell 12. |
<– |
RRCConnectionReconfiguration |
– |
– |
|
– |
EXCEPTION: In parallel to the event described in step 6 the steps specified in Table 8.6.4.4.3.2-3 should take place. |
– |
– |
– |
– |
|
6 |
Wait for 1 s to ensure that T304 expires. The SS changes Cell 12 parameter according to the row "T2" in table 8.6.4.4.3.2-1. |
– |
– |
– |
– |
|
7 |
The UE transmits an RRCConnectionReestablishmentRequest message on Cell 1 |
–> |
RRCConnectionReestablishmentRequest |
– |
– |
|
8 |
The SS transmits an RRCConnectionReestablishment message to resume SRB1 operation and re-activate security on Cell 1. |
<– |
RRCConnectionReestablishment |
– |
– |
|
9 |
Check: Does the UE transmit an RRCConnectionReestablishmentComplete message with rlf-InfoAvailable included? |
–> |
RRCConnectionReestablishmentComplete |
1 |
P |
|
10 |
The SS transmits an RRCConnectionReconfiguration message to resume existing radio bearer on Cell 1. |
<– |
RRCConnectionReconfiguration |
– |
– |
|
11 |
The UE transmits an RRCConnectionReconfigurationComplete message on Cell 1. |
–> |
RRCConnectionReconfigurationtComplete |
– |
– |
|
12 |
The SS changes Cell 4 parameter according to the row "T3" in table 8.6.4.4.3.2-1. |
– |
– |
– |
– |
|
13 |
The UE transmits a MeasurementReport message on Cell 1 to report event A3 with the measured RSRP, RSRQ value for Cell 4. |
–> |
MeasurementReport |
– |
– |
|
14 |
The SS transmits an RRCConnectionReconfiguration message on Cell 1 to order the UE to perform intra frequency handover to Cell 4. |
<– |
RRCConnectionReconfiguration |
– |
– |
|
15 |
Check: Does the UE transmit an RRCConnectionReconfigurationComplete message on Cell 4 with rlf-InfoAvailable included? |
–> |
RRCConnectionReconfigurationComplete |
2 |
P |
|
16 |
The SS transmits a UEInformationRequest message with rlf-ReportReq set to true on Cell 4. |
<– |
UEInformationRequest |
– |
– |
|
17 |
Check: Does the UE transmit a UEInformationResponse message on Cell 4 with rlf-Report included? Check: Does the reestablishmentCellId included in the UEInformationResponse message equal to the global cell identity of Cell 1? |
–> |
UEInformationResponse |
3,4 |
P |
|
18 |
The SS transmits an RRCConnectionReconfiguration message to activate the measurement gaps on Cell 4 |
<– |
RRCConnectionReconfiguration |
– |
– |
|
19 |
The UE transmits an RRCConnectionReconfigurationComplete message to confirm the activation of the measurement gaps on Cell 4. |
–> |
RRCConnectionReconfigurationtComplete |
– |
– |
|
20 |
The SS changes Cell 1, Cell 4 and Cell – 12 parameters according to the row "T4" in table 8.6.4.4.3.2-1. |
– |
– |
– |
– |
|
21 |
The UE transmits a MeasurementReport message on Cell 4 to report event A3 with the measured RSRP, RSRQ value for Cell 12. |
–> |
MeasurementReport |
– |
– |
|
22 |
The SS transmits an RRCConnectionReconfiguration message on Cell 4 to order the UE to perform inter frequency handover to Cell 12. |
<– |
RRCConnectionReconfiguration |
– |
– |
|
– |
EXCEPTION: In parallel to the events described in step 23 the steps specified in Table 8.6.4.4.3.2-3 should take place. |
– |
– |
– |
– |
|
23 |
The SS changes Cell 4 power level according to the row "T5" in table 8.6.4.4.3.2-1. |
– |
– |
– |
– |
|
24 |
The UE transmits an RRCConnectionReestablishmentRequest message on Cell 12 |
–> |
RRCConnectionReestablishmentRequest |
– |
– |
|
25 |
The SS transmits an RRCConnectionReestablishment message to resume SRB1 operation and re-activate security on Cell 12. |
<– |
RRCConnectionReestablishment |
– |
– |
|
26 |
Check: Does the UE transmit an RRCConnectionReestablishmentComplete message with rlf-InfoAvailable included? |
–> |
RRCConnectionReestablishmentComplete |
1 |
P |
|
27 |
The SS transmits an RRCConnectionReconfiguration message to resume existing radio bearer on Cell 12. |
<– |
RRCConnectionReconfiguration |
– |
– |
|
28 |
The UE transmits an RRCConnectionReconfigurationComplete message on Cell 12. |
–> |
RRCConnectionReconfigurationtComplete |
– |
– |
|
29 |
The UE transmits a TRACKING AREA UPDATE REQUEST message on Cell 12. |
– |
– |
– |
– |
|
30 |
SS responds with a TRACKING AREA UPDATE ACCEPT message. NOTE: The TAU is accepted with PLMN1 listed as an Equivalent PLMN |
– |
– |
– |
– |
|
31 |
The UE transmits a TRACKING AREA UPDATE COMPLETE message. |
– |
– |
– |
– |
|
– |
EXCEPTION: Steps 31Aa1 and 31Aa2 depend on the UE implementation. The lower letter indicates a branch that will take place depending on the UE release. |
– |
– |
– |
– |
|
31Aa1 |
IF Rel-10 UE THEN the SS transmits a UEInformationRequest message with rlf-ReportReq set to true on Cell 12. |
<– |
UEInformationRequest |
– |
– |
|
31Aa2 |
Check: Does the UE transmit a UEInformationResponse message on Cell 12 without rlf-Report included? |
–> |
UEInformationResponse |
5 |
P |
|
32 |
Void |
||||
|
33 |
Void |
||||
|
34 |
Check: Does the test result of generic test procedure in TS 36.508 subclause 6.4.2.3 indicate that the UE is in E-UTRA RRC_CONNECTED state on Cell 12? |
– |
– |
1 |
– |
Table 8.6.4.4.3.2-3: Parallel behaviour
|
St |
Procedure |
Message Sequence |
TP |
Verdict |
|
|
U – S |
Message |
||||
|
– |
EXCEPTION: The steps 1 and 2 below are repeated for the duration of T304. |
– |
– |
– |
– |
|
1 |
The UE attempts to perform the inter frequency handover using MAC Random Access Preamble on Cell 12. |
– |
– |
– |
– |
|
2 |
The SS does not respond. |
– |
– |
– |
– |
Table 8.6.4.4.3.2-4: Void
8.6.4.4.3.3 Specific message contents
Table 8.6.4.4.3.3-0: SystemInformationBlockType2 for Cell 1, Cell 4 and Cell 12 (preamble and all the steps in Table 8.6.4.4.3.2-2)
|
Derivation Path: 36.508, Table 4.6.3-12 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
ra-SupervisionInfo SEQUENCE { |
|||
|
preambleTransMax |
n50 |
||
|
} |
|||
Table 8.6.4.4.3.3-0: Conditions for specific message contents
in Tables 8.6.4.4.3.3-2, 8.6.4.4.3.3-5, 8.6.4.4.3.3-14 and 8.6.4.4.3.3-18
|
Condition |
Explanation |
|
Band > 64 |
This condition applies if the band number is bigger than 64. |
|
Band 24 High range |
If Band 24 high frequency range is selected for the target cell |
Table 8.6.4.4.3.3-1: RRCConnectionReconfiguration (step 1, Table 8.6.4.4.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-8, condition MEAS |
Table 8.6.4.4.3.3-2: MeasConfig (Table 8.6.4.4.3.3-1)
|
Derivation Path: 36.508, Table 4.6.6-1, condition INTER-FREQ |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MeasConfig SEQUENCE { |
|||
|
measObjectToAddModList SEQUENCE (SIZE (1..maxObjectId)) OF SEQUENCE { |
2 entries |
||
|
measObjectId[1] |
IdMeasObject-f1 |
||
|
measObject[1] |
MeasObjectEUTRA-GENERIC(f1) |
||
|
measObect[1] |
MeasObjectEUTRA-GENERIC(maxEARFCN) |
Band > 64 |
|
|
measObjectId[2] |
IdMeasObject-f2 |
||
|
measObject[2] |
MeasObjectEUTRA-GENERIC(f2) |
||
|
measObect[2] |
MeasObjectEUTRA-GENERIC(maxEARFCN) |
Band > 64 |
|
|
} |
|||
|
reportConfigToAddModList SEQUENCE (SIZE (1..maxReportConfigId)) OF SEQUENCE { |
1 entry |
||
|
reportConfigId[1] |
IdReportConfig-A3 |
||
|
reportConfig[1] |
ReportConfigEUTRA-A3 |
||
|
} |
|||
|
measIdToAddModList SEQUENCE (SIZE (1..maxMeasId)) OF SEQUENCE { |
2 entries |
||
|
measId[1] |
1 |
||
|
measObjectId[1] |
IdMeasObject-f1 |
||
|
reportConfigId[1] |
IdReportConfig-A3 |
||
|
measId[2] |
2 |
||
|
measObjectId[2] |
IdMeasObject-f2 |
||
|
reportConfigId[2] |
IdReportConfig-A3 |
||
|
} |
|||
|
measObjectToAddModList-v9e0 SEQUENCE (SIZE (1..maxObjectId)) OF SEQUENCE { |
Band > 64 |
||
|
measObjectEUTRA-v9e0[1] SEQUENCE { |
|||
|
carrierFreq-v9e0 |
Same downlink EARFCN as used for f1 |
||
|
} |
|||
|
measObjectEUTRA-v9e0[2] SEQUENCE { |
|||
|
carrierFreq-v9e0 |
Same downlink EARFCN as used for f2 |
||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.4.3.3-3: MeasurementReport (step 4, Table 8.6.4.4.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-5 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MeasurementReport ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
measurementReport-r8 SEQUENCE { |
|||
|
measResults SEQUENCE { |
|||
|
measId |
2 |
||
|
measResultPcell SEQUENCE { |
Cell 1 |
||
|
rsrpResult |
(0..97) |
||
|
rsrqResult |
(0..34) |
||
|
} |
|||
|
measResultNeighCells CHOICE { |
|||
|
measResultListEUTRA SEQUENCE (SIZE (1..maxCellReport)) OF SEQUENCE { |
1 entry |
||
|
physCellId[1] |
PhysicalCellIdentity of Cell 12 |
||
|
cgi-Info[1] |
Not present |
||
|
measResult[1] SEQUENCE { |
|||
|
rsrpResult |
(0..97) |
||
|
rsrqResult |
(0..34) |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.4.3.3-4: RRCConnectionReconfiguration (step 5, step 14 and step 22, Table 8.6.4.4.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-8, condition HO |
Table 8.6.4.4.3.3-5: MobilityControlInfo (step 5, Table 8.6.4.4.3.3-4)
|
Derivation Path: 36.308, Table 4.6.5-1 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MobilityControlInfo ::= SEQUENCE { |
|||
|
targetPhysCellId |
PhysicalCellIdentity of Cell 12 |
||
|
carrierFreq SEQUENCE { |
|||
|
dl-CarrierFreq |
Same downlink EARFCN as used for Cell 12 |
||
|
ul-CarrierFreq |
Not present |
||
|
Same uplink EARFCN as used for Cell 12 |
Band 24 High range |
||
|
} |
|||
|
rach-ConfigDedicated SEQUENCE { |
|||
|
ra-PreambleIndex |
63 |
||
|
ra-PRACH-MaskIndex |
0 |
||
|
} |
|||
|
carrierFreq-v9e0 SEQUENCE { |
Band > 64 |
||
|
dl-CarrierFreq-v9e0 |
Same downlink EARFCN as used for Cell 12 |
||
|
} |
|||
Table 8.6.4.4.3.3-6: RRCConnectionReestablishmentRequest (step 7, Table 8.6.4.4.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-13 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishmentRequest ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
rrcConnectionReestablishmentRequest-r8 SEQUENCE { |
|||
|
ue-Identity SEQUENCE { |
|||
|
c-RNTI |
the value of the C-RNTI of the UE |
||
|
physCellId |
PhysicalCellIdentity of Cell 1 |
||
|
shortMAC-I |
The same value as the 16 least significant bits of the XMAC-I value calculated by SS. |
||
|
} |
|||
|
reestablishmentCause |
handoverFailure |
||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.4.3.3-7: RRCConnectionReestablishment (step 8, Table 8.6.4.4.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-10 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishment ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
rrcConnectionReestablishment-r8 SEQUENCE { |
|||
|
nextHopChainingCount |
0 |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.4.3.3-8: RRCConnectionReestablishmentComplete (step 9 and step 26, Table 8.6.4.4.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-11 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishmentComplete ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
rrcConnectionReestablishmentComplete-r8 = SEQUENCE { |
|||
|
nonCriticalExtension SEQUENCE { |
|||
|
rlf-InfoAvailable-r9 |
true |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.4.3.3-9: RRCConnectionReconfiguration (step 10, Table 8.6.4.4.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-8 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReconfiguration ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
rrcConnectionReconfiguration-r8 SEQUENCE { |
|||
|
radioResourceConfigDedicated |
RadioResourceConfigDedicated-HO |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.4.3.3-10: MeasurementReport (step 13, Table 8.6.4.4.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-5 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MeasurementReport ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
measurementReport-r8 SEQUENCE { |
|||
|
measResults SEQUENCE { |
|||
|
measId |
1 |
||
|
measResultPcell SEQUENCE { |
Cell 1 |
||
|
rsrpResult |
(0..97) |
||
|
rsrqResult |
(0..34) |
||
|
} |
|||
|
measResultNeighCells CHOICE { |
|||
|
measResultListEUTRA SEQUENCE (SIZE (1..maxCellReport)) OF SEQUENCE { |
1 entry |
||
|
physCellId[1] |
PhysicalCellIdentity of Cell 4 |
||
|
cgi-Info[1] |
Not present |
||
|
measResult[1] SEQUENCE { |
|||
|
rsrpResult |
(0..97) |
||
|
rsrqResult |
(0..34) |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.4.3.3-11: MobilityControlInfo (step 14, Table 8.6.4.4.3.3-4)
|
Derivation Path: 36.308, Table 4.6.5-1 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MobilityControlInfo ::= SEQUENCE { |
|||
|
targetPhysCellId |
PhysicalCellIdentity of Cell 4 |
||
|
carrierFreq |
Not present |
||
|
rach-ConfigDedicated SEQUENCE { |
|||
|
ra-PreambleIndex |
63 |
||
|
ra-PRACH-MaskIndex |
0 |
||
|
} |
|||
|
} |
|||
Table 8.6.4.4.3.3-12: RRCConnectionReconfigurationComplete (step 15, Table 8.6.4.4.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-9 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
RRCConnectionReconfigurationComplete ::= SEQUENCE { |
||||
|
rrc-TransactionIdentifier |
RRC-TransactionIdentifier-UL |
|||
|
criticalExtensions CHOICE { |
||||
|
rrcConnectionReconfigurationComplete-r8 SEQUENCE { |
||||
|
nonCriticalExtension SEQUENCE { |
||||
|
nonCriticalExtension SEQUENCE { |
||||
|
rlf-InfoAvailable-r10 |
true |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
Table 8.6.4.4.3.3-13: UEInformationRequest (step 16 and step 31Aa1, Table 8.6.4.4.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23A |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
UEInformationRequest-r9 ::=SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE { |
|||
|
ueInformationRequest-r9 SEQUENCE { |
|||
|
rlf-ReportReq-r9 |
TRUE |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.4.3.3-14: UEInformationResponse (step 17, Table 8.6.4.4.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23B |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
UEInformationResponse-r9 ::=SEQUENCE { |
||||
|
criticalExtensions CHOICE { |
||||
|
c1 CHOICE { |
||||
|
ueInformationResponse-r9 SEQUENCE { |
||||
|
rlf-Report-r9 SEQUENCE { |
||||
|
measResultLastServCell-r9 SEQUENCE { |
Cell 1 |
|||
|
rsrpResult-r9 |
(0..97) |
|||
|
rsrqResult-r9 |
Not present or (0..34) |
|||
|
} |
||||
|
measResultNeighCells-r9 SEQUENCE { |
||||
|
measResultListEUTRA-r9 SEQUENCE(SIZE(1..maxFreq)) OF SEQUENCE { |
1 entry |
|||
|
carrierFreq-r9 |
The ARFCN of Cell 12 |
|||
|
carrierFreq-r9[1] |
maxEARFCN |
Band > 64 |
||
|
measResultList-r9 SEQUENCE (SIZE (1..maxCellReport)) OF SEQUENCE { |
||||
|
physCellId |
Phys cell id of cell 12 |
|||
|
cgi-Info |
Not present |
|||
|
measResult SEQUENCE { |
||||
|
rsrpResult |
(0..97) |
|||
|
rsrqResult |
Not present or (0..34) |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
locationInfo-r10 |
Not present or any allowed value |
|||
|
failedPCellId-r10 CHOICE { |
cellGlobalId-r10 or pci-arfcn-r10 |
If the UE has the global cell identity depending on UE implementation, the UE sets the global cell identity, otherwise the UE sets the physical cell identity and the carrier frequency. |
Target PCell |
|
|
cellGlobalId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 12 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 12 |
|||
|
} |
||||
|
pci-arfcn-r10 SEQUENCE { |
||||
|
physCellId-r10 |
PhysicalCellIdentity of Cell 12 |
|||
|
carrierFreq-r10 |
Same downlink EARFCN as used for Cell 12 |
|||
|
carrierFreq-r10 |
maxEARFCN |
Band > 64 |
||
|
} |
||||
|
} |
||||
|
reestablishmentCellId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 1 |
“Verify setting of reestablishmentCellId in the VarRLF-Report to the global cell identity of the selected cell at RRC connection re-establishment due to handover failure” |
||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
} |
||||
|
timeConnFailure-r10 |
Not Checked/Present |
|||
|
connectionFailureType-r10 |
hof |
|||
|
previousPCellId-r10 SEQUENCE { |
Source PCell |
|||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 1 |
plmn-Identity |
||
|
cellIdentity |
cellIdentity of Cell 1 |
cellIdentity |
||
|
} |
||||
|
failedPCellId-v1090 SEQUENCE { |
Band > 64 |
|||
|
carrierFreq-v1090 |
Not present or the same downlink EARFCN as used for Cell 12 |
|||
|
} |
||||
|
} |
||||
|
nonCriticalExtension SEQUENCE { |
Band > 64 |
|||
|
lateNonCriticalExtension SEQUENCE { |
||||
|
rlf-Report-v9e0 SEQUENCE { |
||||
|
measResultListEUTRA-v9e0 SEQUENCE (SIZE (1..maxFreq)) OF SEQUENCE { |
||||
|
carrierFreq-v9e0[1] |
Same downlink EARFCN as used for Cell 12 |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
Table 8.6.4.4.3.3-15: RRCConnectionReconfiguration (step 18, Table 8.6.4.4.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-8, condition MEAS |
Table 8.6.4.4.3.3-16: MeasConfig (Table 8.6.4.4.3.3-15)
|
Derivation Path: 36.508, Table 4.6.6-1, condition INTER-FREQ |
Table 8.6.4.4.3.3-17: MeasurementReport (step 21, Table 8.6.4.4.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-5 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MeasurementReport ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
measurementReport-r8 SEQUENCE { |
|||
|
measResults SEQUENCE { |
|||
|
measId |
2 |
||
|
measResultPcell SEQUENCE { |
Cell 4 |
||
|
rsrpResult |
(0..97) |
||
|
rsrqResult |
(0..34) |
||
|
} |
|||
|
measResultNeighCells CHOICE { |
|||
|
measResultListEUTRA SEQUENCE (SIZE (1..maxCellReport)) OF SEQUENCE { |
1 entry |
||
|
physCellId[1] |
PhysicalCellIdentity of Cell 12 |
||
|
cgi-Info[1] |
Not present |
||
|
measResult[1] SEQUENCE { |
|||
|
rsrpResult |
(0..97) |
||
|
rsrqResult |
(0..34) |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.4.3.3-18: MobilityControlInfo (step 22, Table 8.6.4.4.3.3-4)
|
Derivation Path: 36.308, Table 4.6.5-1 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MobilityControlInfo ::= SEQUENCE { |
|||
|
targetPhysCellId |
PhysicalCellIdentity of Cell 12 |
||
|
carrierFreq SEQUENCE { |
|||
|
dl-CarrierFreq |
Same downlink EARFCN as used for Cell 12 |
||
|
ul-CarrierFreq |
Not present |
||
|
Same uplink EARFCN as used for Cell 12 |
Band 24 High range |
||
|
} |
|||
|
rach-ConfigDedicated SEQUENCE { |
|||
|
ra-PreambleIndex |
63 |
||
|
ra-PRACH-MaskIndex |
0 |
||
|
} |
|||
|
carrierFreq-v9e0 SEQUENCE { |
Band > 64 |
||
|
dl-CarrierFreq-v9e0 |
Same downlink EARFCN as used for Cell 12 |
||
|
} |
|||
Table 8.6.4.4.3.3-19: RRCConnectionReestablishmentRequest (step 24, Table 8.6.4.4.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-13 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishmentRequest ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
rrcConnectionReestablishmentRequest-r8 SEQUENCE { |
|||
|
ue-Identity SEQUENCE { |
|||
|
c-RNTI |
the value of the C-RNTI of the UE |
||
|
physCellId |
PhysicalCellIdentity of Cell 4 |
||
|
shortMAC-I |
The same value as the 16 least significant bits of the XMAC-I value calculated by SS. |
||
|
} |
|||
|
reestablishmentCause |
handoverFailure |
||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.4.3.3-20: UEInformationResponse (step 31Aa2, Table 8.6.4.4.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23B |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
UEInformationResponse-r9 ::= SEQUENCE { |
||||
|
rrc-TransactionIdentifier |
RRC-TransactionIdentifier-UL |
|||
|
criticalExtensions CHOICE { |
||||
|
c1 CHOICE{ |
||||
|
ueInformationResponse-r9 SEQUENCE { |
||||
|
rlf-Report-r9 SEQUENCE {} |
Not present |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
Table 8.6.4.4.3.3-21: ATTACH ACCEPT for Cell 1 (preamble)
|
Derivation path: 36.508 Table 4.7.2-1 |
|||
|
Information Element |
Value/Remark |
Comment |
Condition |
|
Equivalent PLMNs |
PLMN2 |
||
Table 8.6.4.4.3.3-22: TRACKING AREA UPDATE ACCEPT for Cell 12 (step 30, Table 8.6.4.4.3.2-2)
|
Derivation path: 36.508 Table 4.7.2-24 |
|||
|
Information Element |
Value/Remark |
Comment |
Condition |
|
Equivalent PLMNs |
PLMN1 |
||
8.6.4.5 Radio Link Failure logging / Reporting of ECGI of the PCell
8.6.4.5.1 Test Purpose (TP)
(1)
with { UE in RRC_CONNECTED having performed intra-frequency handover and reported that the UE has radio link failure information available }
ensure that {
when { UE receives the UEInformationRequest message containing rlf-ReportReq }
then { UE sends the UEInformationResponse message containing previousPCellId }
}
8.6.4.5.2 Conformance requirements
References: The conformance requirements covered in the present TC are specified in: TS 36.331, clause 5.3.7.4, 5.3.7.5, 5.3.11.3 and 5.6.5.3.
[TS 36.331, clause 5.3.7.4]
If the procedure was initiated due to radio link failure or handover failure, the UE shall:
1> set the reestablishmentCellId in the VarRLF-Report to the global cell identity of the selected cell;
[TS 36.331, clause 5.3.7.5]
The UE shall:
…
1> set the content of RRCConnectionReestablishmentComplete message as follows:
2> if the UE has radio link failure or handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN:
3> include the rlf-InfoAvailable;
…
1> submit the RRCConnectionReestablishmentComplete message to lower layers for transmission, upon which the procedure ends;
[TS 36.331, clause 5.3.11.3]
The UE shall:
1> upon T310 expiry; or
1> upon random access problem indication from MAC while neither T300, T301, T304 nor T311 is running; or
1> upon indication from RLC that the maximum number of retransmissions has been reached:
2> consider radio link failure to be detected;
2> store the following radio link failure information in the VarRLF-Report by setting its fields as follows:
3> clear the information included in VarRLF-Report, if any;
3> set the plmn-Identity to the RPLMN;
3> set the measResultLastServCell to include the RSRP and RSRQ, if available, of the PCell based on measurements collected up to the moment the UE detected radio link failure;
3> set the measResultNeighCells to include the best measured cells, other than the PCell, ordered such that the best cell is listed first, and based on measurements collected up to the moment the UE detected radio link failure, and set its fields as follows;
4> if the UE was configured to perform measurements for one or more EUTRA frequencies, include the measResultListEUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring UTRA frequencies, include the measResultListUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring GERAN frequencies, include the measResultListGERAN;
4> if the UE was configured to perform measurement reporting for one or more neighbouring CDMA2000 frequencies, include the measResultsCDMA2000;
NOTE: The measured quantities are filtered by the L3 filter as configured in the mobility measurement configuration. The measurements are based on the time domain measurement resource restriction, if configured. Blacklisted cells are not required to be reported.
3> if detailed location information is available, set the content of the locationInfo as follows:
4> include the locationCoordinates;
4> include the horizontalVelocity, if available;
3> set the failedPCellId to the global cell identity, if available, and otherwise to the physical cell identity and carrier frequency of the PCell where radio link failure is detected;
3> if an RRCConnectionReconfiguration message including the mobilityControlInfo was received before the connection failure:
4> include previousPCellId and set it to the global cell identity of the PCell where the last RRCConnectionReconfiguration including the mobilityControlInfo message was received;
4> set the timeConnFailure to the elapsed time since reception of the last RRCConnectionReconfiguration message including the mobilityControlInfo;
3> set the connectionFailureType to rlf;
2> if AS security has not been activated:
3> perform the actions upon leaving RRC_CONNECTED as specified in 5.3.12, with release cause ‘other’;
2> else:
3> initiate the connection re-establishment procedure as specified in 5.3.7;
The UE may discard the radio link failure information, i.e. release the UE variable VarRLF-Report 48, hours after the radio link failure is detected, upon power off or upon detach.
[TS 36.331, clause 5.6.5.3]
Upon receiving the UEInformationRequest message, the UE shall:
…
1> if rlf-ReportReq is set to true and the UE has radio link failure information or handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN, set the rlf-Report in the UEInformationResponse message to the value of rlf-Report in VarRLF-Report;
1> if the rlf-Report is included in UEInformationResponse:
2> discard the rlf-Report from VarRLF-Report upon successful delivery of the UEInformationResponse message confirmed by lower layers.
…
1> if the logMeasReport is included in the UEInformationResponse:
…
1> else:
2> submit the UEInformationResponse message to lower layers for transmission via SRB1;
8.6.4.5.3 Test description
8.6.4.5.3.1 Pre-test conditions
System Simulator:
– Cell 1 and Cell 2
UE:
None.
Preamble:
– The UE is in state Generic RB Established (state 3) on Cell 1 according to [18].
8.6.4.5.3.2 Test procedure sequence
Table 8.6.4.5.3.2-1 illustrates the downlink power levels and other changing parameters to be applied for the cells at various time instants of the test execution. Row marked "T0" denotes the initial conditions after preamble, while columns marked "T1", "T2" and "T3" are to be applied subsequently. The exact instants on which these values shall be applied are described in the texts in this clause.
Table 8.6.4.5.3.2-1: Time instances of cell power level and parameter changes
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Remark |
|
|
T0 |
Cell-specific RS EPRE |
dBm/15kHz |
-85 |
-91 |
The power level values are such that measurement results for Cell 1 (M1) and Cell 2 (M2) satisfy exit condition for event A3 (M2 < M1). |
|
T1 |
Cell-specific RS EPRE |
dBm/15kHz |
-85 |
-79 |
The power level values are such that measurement results for Cell 1 (M1) and Cell 2 (M2) satisfy entry condition for event A3 (M2 > M1). |
|
T2 |
Cell-specific RS EPRE |
dBm/15kHz |
"Off" |
"Off" |
No Cells are available. (NOTE 1). |
|
T3 |
Cell-specific RS EPRE |
dBm/15kHz |
"Off" |
-85 |
Only Cell 2 is available. (NOTE 1) |
|
NOTE 1: Power level “Off” is defined in TS 36.508 Table 6.2.2.1-1. |
|||||
Table 8.6.4.5.3.2-2: Main behaviour
|
St |
Procedure |
Message Sequence |
TP |
Verdict |
|
|
U – S |
Message |
||||
|
1 |
The SS transmits an RRCConnectionReconfiguration message to setup intra-frequency measurement on Cell 1. |
<– |
RRCConnectionReconfiguration |
– |
– |
|
2 |
The UE transmits an RRCConnectionReconfigurationComplete message on Cell 1. |
–> |
RRCConnectionReconfigurationComplete |
– |
– |
|
3 |
The SS changes Cell 2 parameter according to the row "T1" in Table 8.6.4.5.3.2-1. |
– |
– |
– |
– |
|
4 |
The UE transmits a MeasurementReport message on Cell 1. |
–> |
MeasurementReport |
– |
– |
|
5 |
The SS transmits an RRCConnectionReconfiguration message on Cell 1 to order the UE to perform intra-frequency handover to Cell 2. |
<– |
RRCConnectionReconfiguration |
– |
– |
|
6 |
The UE transmits an RRCConnectionReconfigurationComplete message on Cell 2. |
–> |
RRCConnectionReconfigurationComplete |
– |
– |
|
6A |
Wait for 1s to ensure that the UE completes the acquisition of essential SI |
– |
– |
– |
– |
|
7 |
The SS changes Cell 1 and Cell 2 parameter according to the row "T2" in Table 8.6.4.5.3.2-1. |
– |
– |
– |
– |
|
8 |
Wait for 3s to ensure that the UE detects T310 expiry. |
– |
– |
– |
– |
|
9 |
The SS changes Cell 2 parameter according to the row "T3" in Table 8.6.4.5.3.2-1. |
– |
– |
– |
– |
|
10 |
The UE transmits an RRCConnectionReestablishmentRequest message on Cell 2. |
–> |
RRCConnectionReestablishmentRequest |
– |
– |
|
11 |
The SS transmits an RRCConnectionReestablishment message on Cell 2. |
<– |
RRCConnectionReestablishment |
– |
– |
|
12 |
The UE transmits an RRCConnectionReestablishmentComplete message with radio link failure information on Cell 2. |
–> |
RRCConnectionReestablishmentComplete |
– |
– |
|
13 |
The SS transmits an RRCConnectionReconfiguration message on Cell 2. |
<– |
RRCConnectionReconfiguration |
– |
– |
|
14 |
The UE transmits an RRCConnectionReconfigurationComplete message on Cell 2. |
–> |
RRCConnectionReconfigurationComplete |
– |
– |
|
15 |
The SS transmits a UEInformationRequest message on Cell 2. |
<– |
UEInformationRequest |
– |
– |
|
16 |
Check: Does the UE transmit a UEInformationResponse message on Cell 2? |
–> |
UEInformationResponse |
1 |
P |
|
17 |
Check: Does the test result of generic test procedure in TS 36.508 subclause 6.4.2.3 indicate that the UE is in E-UTRA RRC_CONNECTED state on Cell 2? |
– |
– |
1 |
– |
8.6.4.5.3.3 Specific message contents
Table 8.6.4.5.3.3-0: Conditions for specific message contents
in Tables 8.6.4.5.3.3-2 and 8.6.4.5.3.3-10
|
Condition |
Explanation |
|
Band > 64 |
This condition applies if the band number is bigger than 64. |
Table 8.6.4.5.3.3-1: RRCConnectionReconfiguration (step 1, Table 8.6.4.5.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-8, condition MEAS |
Table 8.6.4.5.3.3-2: MeasConfig (Table 8.6.4.5.3.3-1)
|
Derivation Path: 36.508, Table 4.6.6-1 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MeasConfig ::= SEQUENCE { |
|||
|
measObjectToAddModList SEQUENCE (SIZE (1..maxObjectId)) OF SEQUENCE { |
1 entry |
||
|
measObjectId[1] |
IdMeasObject-f1 |
||
|
measObject[1] |
MeasObjectEUTRA-GENERIC(f1) |
||
|
measObect[1] |
MeasObjectEUTRA-GENERIC(maxEARFCN) |
Band > 64 |
|
|
} |
|||
|
reportConfigToAddModList SEQUENCE (SIZE (1..maxReportConfigId)) OF SEQUENCE { |
1 entry |
||
|
reportConfigId[1] |
IdReportConfig-A3 |
||
|
reportConfig[1] |
ReportConfigEUTRA-A3 |
||
|
} |
|||
|
measIdToAddModListSEQUENCE (SIZE (1..maxMeasId)) OF SEQUENCE { |
|||
|
measId[1] |
1 |
||
|
measObjectId[1] |
IdMeasObject-f1 |
||
|
reportConfigId[1] |
IdReportConfig-A3 |
||
|
} |
|||
|
measObjectToAddModList-v9e0 SEQUENCE (SIZE (1..maxObjectId)) OF SEQUENCE { |
Band > 64 |
||
|
measObjectEUTRA-v9e0[1] SEQUENCE { |
|||
|
carrierFreq-v9e0 |
Same downlink EARFCN as used for f1 |
||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.5.3.3-3: MeasurementReport (step 4, Table 8.6.4.5.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-5 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MeasurementReport ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
measurementReport-r8 SEQUENCE { |
|||
|
measResults SEQUENCE { |
|||
|
measId |
1 |
||
|
measResultPCell SEQUENCE { |
|||
|
rsrpResult |
(0..97) |
||
|
rsrqResult |
(0..34) |
||
|
} |
|||
|
measResultNeighCells CHOICE { |
|||
|
measResultListEUTRA SEQUENCE (SIZE (1..maxCellReport)) OF SEQUENCE { |
1 entry |
||
|
physCellId |
PhysicalCellIdentity of Cell 2 |
||
|
cgi-Info |
Not present |
||
|
measResult SEQUENCE { |
|||
|
rsrpResult |
(0..97) |
||
|
rsrqResult |
(0..34) |
||
|
additionalSI-Info-r9 |
Not present |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
measResultForECID-r9 |
Not present |
||
|
locationInfo-r10 |
Not present |
||
|
measResultServFreqList-r10 |
Not present |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.5.3.3-4: RRCConnectionReconfiguration (step 5, Table 8.6.4.5.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-8, condition HO |
Table 8.6.4.5.3.3-5: MobilityControlInfo (Table 8.6.4.5.3.3-4)
|
Derivation Path: 36.508, Table 4.6.5-1 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MobilityControlInfo ::= SEQUENCE { |
|||
|
targetPhysCellId |
PhysicalCellIdentity of Cell 2 |
||
|
carrierFreq |
Not present |
||
|
} |
|||
Table 8.6.4.5.3.3-6: RRCConnectionReestablishmentRequest (step 10, Table 8.6.4.5.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-13 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishmentRequest ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
rrcConnectionReestablishmentRequest-r8 SEQUENCE { |
|||
|
ue-Identity SEQUENCE { |
|||
|
c-RNTI |
the value of the C-RNTI of the UE |
||
|
physCellId |
PhysicalCellIdentity of Cell 2 |
||
|
shortMAC-I |
The same value as the 16 least significant bits of the XMAC-I value calculated by SS |
||
|
} |
|||
|
reestablishmentCause |
otherFailure |
||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.5.3.3-7: RRCConnectionReestablishmentComplete (step 12, Table 8.6.4.5.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-11 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishmentComplete ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
rrcConnectionReestablishmentComplete-r8 = SEQUENCE { |
|||
|
nonCriticalExtension SEQUENCE { |
|||
|
rlf-InfoAvailable-r9 |
true |
||
|
nonCriticalExtension |
Not present or any allowed value |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.5.3.3-8: RRCConnectionReconfiguration (step 13, Table 8.6.4.5.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-8 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReconfiguration ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
rrcConnectionReconfiguration-r8 SEQUENCE { |
|||
|
radioResourceConfigDedicated |
RadioResourceConfigDedicated-HO |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.5.3.3-9: UEInformationRequest (step 15, Table 8.6.4.5.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23A |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
UEInformationRequest-r9 ::=SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE { |
|||
|
ueInformationRequest-r9 SEQUENCE { |
|||
|
rlf-ReportReq-r9 |
TRUE |
||
|
logMeasReportReq-r10 |
Not present |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.5.3.3-10: UEInformationResponse (step 16, Table 8.6.4.5.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23B |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
UEInformationResponse-r9 ::=SEQUENCE { |
||||
|
criticalExtensions CHOICE { |
||||
|
c1 CHOICE { |
||||
|
ueInformationResponse-r9 SEQUENCE { |
||||
|
rlf-Report-r9 SEQUENCE { |
||||
|
measResultLastServCell-r9 SEQUENCE { |
||||
|
rsrpResult-r9 |
(0..97) |
|||
|
rsrqResult-r9 |
Not present or (0..34) |
|||
|
} |
||||
|
measResultNeighCells-r9 |
Not present |
|||
|
locationInfo-r10 |
Not present or any allowed value |
|||
|
failedPCellId-r10 CHOICE { |
cellGlobalId-r10 or pci-arfcn-r10 |
If the UE has the global cell identity depending on UE implementation, the UE sets the global cell identity, otherwise the UE sets the physical cell identity and the carrier frequency. |
||
|
cellGlobalId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 2 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 2 |
|||
|
} |
||||
|
pci-arfcn-r10 SEQUENCE { |
||||
|
physCellId-r10 |
Physical cell Identity of Cell 2 |
|||
|
carrierFreq-r10 |
Same downlink EARFCN as used for Cell 2 |
|||
|
carrierFreq-r10 |
maxEARFCN |
Band > 64 |
||
|
} |
||||
|
} |
||||
|
reestablishmentCellId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 2 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 2 |
|||
|
} |
||||
|
failedPCellId-v1090 SEQUENCE { |
Band > 64 |
|||
|
carrierFreq-v1090 |
Not present or the same downlink EARFCN as used for Cell 2 |
|||
|
} |
||||
|
timeConnFailure-r10 |
Any allowed value |
|||
|
connectionFailureType-r10 |
rlf |
|||
|
previousPCellId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
8.6.4.6 Void
8.6.4.7 Radio Link Failure logging / Location information
8.6.4.7.1 Test Purpose (TP)
(1)
with { UE in RRC_CONNECTED having performed the intra-frequency measurement and reported that the UE has radio link failure information with location information available }
ensure that {
when { UE receives the UEInformationRequest message containing rlf-ReportReq }
then { UE sends the UEInformationResponse message containing the measurement result for intra-frequency neighbour cell including locationCoordinates }
}
8.6.4.7.2 Conformance requirements
References: The conformance requirements covered in the present TC are specified in: TS 34.306, clause 4.3.13.2; TS 36.331, clause 5.3.11.3 and 5.6.5.3.
[TS 36.306, clause 4.3.13.2 (TP1)]
standaloneGNSS-Location
This parameter defines whether the UE is equipped with a standalone GNSS receiver that may be used to provide detailed location information in RRC measurement report and logged measurements in RRC_IDLE.
[TS 36.331, clause 5.3.11.3]
The UE shall:
1> upon T310 expiry; or
1> upon random access problem indication from MAC while neither T300, T301, T304 nor T311 is running; or
1> upon indication from RLC that the maximum number of retransmissions has been reached:
2> consider radio link failure to be detected;
2> store the following radio link failure information in the VarRLF-Report by setting its fields as follows:
3> clear the information included in VarRLF-Report, if any;
3> set the plmn-Identity to the RPLMN;
3> set the measResultLastServCell to include the RSRP and RSRQ, if available, of the PCell based on measurements collected up to the moment the UE detected radio link failure;
3> set the measResultNeighCells to include the best measured cells, other than the PCell, ordered such that the best cell is listed first, and based on measurements collected up to the moment the UE detected radio link failure, and set its fields as follows;
4> if the UE was configured to perform measurements for one or more EUTRA frequencies, include the measResultListEUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring UTRA frequencies, include the measResultListUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring GERAN frequencies, include the measResultListGERAN;
4> if the UE was configured to perform measurement reporting for one or more neighbouring CDMA2000 frequencies, include the measResultsCDMA2000;
NOTE: The measured quantities are filtered by the L3 filter as configured in the mobility measurement configuration. The measurements are based on the time domain measurement resource restriction, if configured. Blacklisted cells are not required to be reported.
3> if detailed location information is available, set the content of the locationInfo as follows:
4> include the locationCoordinates;
4> include the horizontalVelocity, if available;
3> set the failedPCellId to the global cell identity, if available, and otherwise to the physical cell identity and carrier frequency of the PCell where radio link failure is detected;
3> if an RRCConnectionReconfiguration message including the mobilityControlInfo was received before the connection failure:
4> include previousPCellId and set it to the global cell identity of the PCell where the last RRCConnectionReconfiguration including the mobilityControlInfo message was received;
4> set the timeConnFailure to the elapsed time since reception of the last RRCConnectionReconfiguration message including the mobilityControlInfo;
3> set the connectionFailureType to rlf;
2> if AS security has not been activated:
3> perform the actions upon leaving RRC_CONNECTED as specified in 5.3.12, with release cause ‘other’;
2> else:
3> initiate the connection re-establishment procedure as specified in 5.3.7;
The UE may discard the radio link failure information, i.e. release the UE variable VarRLF-Report 48 hours after the radio link failure is detected.
[TS 36.331, clause 5.6.5.3]
Upon receiving the UEInformationRequest message, the UE shall:
…
1> if rlf-ReportReq is set to true and the UE has radio link failure information or handover failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN, set the rlf-Report in the UEInformationResponse message to the value of rlf-Report in VarRLF-Report;
1> if the rlf-Report is included in UEInformationResponse:
2> discard the rlf-Report from VarRLF-Report upon successful delivery of the UEInformationResponse message confirmed by lower layers.
…
1> if the logMeasReport is included in the UEInformationResponse:
…
1> else:
2> submit the UEInformationResponse message to lower layers for transmission via SRB1;
8.6.4.7.3 Test description
8.6.4.7.3.1 Pre-test conditions
System Simulator:
– Cell 1 and Cell 2
UE: None.
Preamble:
– The UE’s positioning engine (e.g. standalone GNSS receiver) should be provided with any necessary stimulus to allow it to provide the position. This shall be done by use of the test function Update UE Location Information defined in TS 36.509 [25] , if supported by the UE according to pc_UpdateUE_LocationInformation. Otherwise, or in addition any other suitable method may also be used.
– The UE is in state Generic RB Established (state 3) on Cell 1 according to [18].
8.6.4.7.3.2 Test procedure sequence
Same test procedure as specified in 8.6.4.1.3.2 with the following exception:
– The specific message content for the UEInformationResponse message in Table 8.6.4.1.3.3-8 is replaced by the specific message content in Table 8.6.4.7.3.3-1.
8.6.4.7.3.3 Specific message contents
Table 8.6.4.7.3.3-1: UEInformationResponse (step 12, Table 8.6.4.1.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23B |
||||||||
|
Information Element |
Value/remark |
Comment |
Condition |
|||||
|
UEInformationResponse-r9 ::=SEQUENCE { |
||||||||
|
criticalExtensions CHOICE { |
||||||||
|
c1 CHOICE { |
||||||||
|
ueInformationResponse-r9 SEQUENCE { |
||||||||
|
rlf-Report-r9 SEQUENCE { |
||||||||
|
measResultLastServCell-r9 SEQUENCE { |
||||||||
|
rsrpResult-r9 |
(0..97) |
|||||||
|
rsrqResult-r9 |
Not present or (0..34) |
|||||||
|
} |
||||||||
|
measResultNeighCells-r9 SEQUENCE { |
||||||||
|
measResultListEUTRA-r9 SEQUENCE (SIZE (1..maxFreq)) OF SEQUENCE { |
1 entry |
|||||||
|
carrierFreq-r9[1] |
Same downlink EARFCN as used for Cell 2 |
|||||||
|
carrierFreq-r9[1] |
maxEARFCN |
Band > 64 |
||||||
|
measResultList-r9[1] SEQUENCE (SIZE (1..maxCellReport)) OF SEQUENCE { |
1 entry |
|||||||
|
physCellId[1] |
Physical cell Identity of Cell 2 |
|||||||
|
cgi-Info[1] |
Not present |
|||||||
|
measResult[1] SEQUENCE { |
||||||||
|
rsrpResult |
(0..97) |
|||||||
|
rsrqResult |
(0..34) |
|||||||
|
additionalSI-Info-r9 |
Not present |
|||||||
|
} |
||||||||
|
} |
||||||||
|
} |
||||||||
|
measResultListUTRA-r9 |
Not present |
|||||||
|
measResultListGERAN-r9 |
Not present |
|||||||
|
measResultsCDMA2000-r9 |
Not present |
|||||||
|
} |
||||||||
|
locationInfo-r10 SEQUENCE { |
||||||||
|
locationCoordinates-r10 CHOICE { |
||||||||
|
ellipsoid-Point-r10 |
Any allowed value |
|||||||
|
ellipsoidPointWithAltitude-r10 |
Any allowed value |
|||||||
|
} |
||||||||
|
} |
||||||||
|
failedPCellId-r10 CHOICE { |
cellGlobalId-r10 or pci-arfcn-r10 |
If the UE has the global cell identity depending on UE implementation, the UE sets the global cell identity, otherwise the UE sets the physical cell identity and the carrier frequency. |
||||||
|
cellGlobalId-r10 SEQUENCE { |
||||||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||||||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||||||
|
} |
||||||||
|
pci-arfcn-r10 SEQUENCE { |
||||||||
|
physCellId-r10 |
Physical cell Identity of Cell 1 |
|||||||
|
carrierFreq-r10 |
Same downlink EARFCN as used for Cell 1 |
|||||||
|
carrierFreq-r10 |
maxEARFCN |
Band > 64 |
||||||
|
} |
||||||||
|
} |
||||||||
|
reestablishmentCellId-r10 SEQUENCE { |
||||||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 2 |
|||||||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 2 |
|||||||
|
} |
||||||||
|
timeConnFailure-r10 |
Not present |
|||||||
|
connectionFailureType-r10 |
rlf |
|||||||
|
previousPCellId-r10 |
Not present |
|||||||
|
failedPCellId-v1090 SEQUENCE { |
Band > 64 |
|||||||
|
carrierFreq-v1090 |
Not present or the same downlink EARFCN as used for Cell 1 |
|||||||
|
} |
||||||||
|
} |
||||||||
|
nonCriticalExtension SEQUENCE { |
Band > 64 |
|||||||
|
lateNonCriticalExtension SEQUENCE { |
||||||||
|
rlf-Report-v9e0 SEQUENCE { |
||||||||
|
measResultListEUTRA-v9e0 SEQUENCE (SIZE (1..maxFreq)) OF SEQUENCE { |
||||||||
|
carrierFreq-v9e0[1] |
Same downlink EARFCN as used for Cell 2 |
|||||||
|
} |
||||||||
|
} |
||||||||
|
} |
||||||||
|
} |
||||||||
|
} |
||||||||
|
} |
||||||||
|
} |
||||||||
|
} |
||||||||
|
Condition |
Explanation |
|
Band > 64 |
This condition applies if the band number is bigger than 64. |
8.6.4.8 Radio Link Failure logging / Logging and reporting / Reporting at RRC connection establishment / PLMN list
8.6.4.8.1 Test Purpose (TP)
(1)
with { UE having completed the radio bearer establishment and initial security activation procedure }
ensure that {
when { UE detects radio link failure and T311 is expired and camp on a cell belonging to equivalent PLMN }
then { UE performs RRC Connection Establishment procedure and sends an RRCConnectionSetupComplete message with rlf-InfoAvailable }
}
(2)
with { UE having sent an RRCConnectionSetupComplete message with rlf-InfoAvailable }
ensure that {
when { UE receives a UEInformationRequest message with rlf-ReportReq set to true }
then { UE sends a UEInformationResponse message with rlf-Report }
}
8.6.4.8.2 Conformance requirements
References: The conformance requirements covered in the present TC are specified in: TS 36.331, clause 5.3.3.4, 5.3.11.3 and 5.6.5.3. Unless otherwise stated these are Rel-11 requirements.
[TS 36.331, clause 5.3.3.4]
The UE shall:
…
1> set the content of RRCConnectionSetupComplete message as follows:
…
2> if the UE has radio link failure or handover failure information available in VarRLF-Report and if the RPLMN is included in plmn-IdentityList stored in VarRLF-Report:
3> include rlf-InfoAvailable;
[TS 36.331, clause 5.3.11.3]
The UE shall:
1> upon T310 expiry; or
1> upon random access problem indication from MAC while neither T300, T301, T304 nor T311 is running; or
1> upon indication from RLC that the maximum number of retransmissions has been reached:
2> consider radio link failure to be detected;
2> store the following radio link failure information in the VarRLF-Report by setting its fields as follows:
3> clear the information included in VarRLF-Report, if any;
3> set the plmn-IdentityList to include the list of EPLMNs stored by the UE (i.e. includes the RPLMN);
3> set the measResultLastServCell to include the RSRP and RSRQ, if available, of the PCell based on measurements collected up to the moment the UE detected radio link failure;
3> set the measResultNeighCells to include the best measured cells, other than the PCell, ordered such that the best cell is listed first, and based on measurements collected up to the moment the UE detected radio link failure, and set its fields as follows;
4> if the UE was configured to perform measurements for one or more EUTRA frequencies, include the measResultListEUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring UTRA frequencies, include the measResultListUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring GERAN frequencies, include the measResultListGERAN;
4> if the UE was configured to perform measurement reporting for one or more neighbouring CDMA2000 frequencies, include the measResultsCDMA2000;
4> for each neighbour cell included, include the optional fields that are available;
…
3> if detailed location information is available, set the content of the locationInfo as follows:
4> include the locationCoordinates;
4> include the horizontalVelocity, if available;
3> set the failedPCellId to the global cell identity, if available, and otherwise to the physical cell identity and carrier frequency of the PCell where radio link failure is detected;
3> if an RRCConnectionReconfiguration message including the mobilityControlInfo was received before the connection failure:
4> if the last RRCConnectionReconfiguration message including the mobilityControlInfo concerned an intra E-UTRA handover:
5> include the previousPCellId and set it to the global cell identity of the PCell where the last RRCConnectionReconfiguration message including mobilityControlInfo was received;
5> set the timeConnFailure to the elapsed time since reception of the last RRCConnectionReconfiguration message including the mobilityControlInfo;
4> if the last RRCConnectionReconfiguration message including the mobilityControlInfo concerned a handover to E-UTRA from UTRA and if the UE supports Radio Link Failure Report for Inter-RAT MRO:
5> include the previousUTRA-CellId and set it to the physical cell identity, the carrier frequency and the global cell identity, if available, of the UTRA Cell in which the last RRCConnectionReconfiguration message including mobilityControlInfo was received;
5> set the timeConnFailure to the elapsed time since reception of the last RRCConnectionReconfiguration message including the mobilityControlInfo;
3> set the connectionFailureType to rlf;
3> set the c-RNTI to the C-RNTI used in the PCell;
3> set the rlf-Cause to the trigger for detecting radio link failure;
2> if AS security has not been activated:
3> perform the actions upon leaving RRC_CONNECTED as specified in 5.3.12, with release cause ‘other’;
2> else:
3> initiate the connection re-establishment procedure as specified in 5.3.7;
The UE may discard the radio link failure information, i.e. release the UE variable VarRLF-Report, 48 hours after the radio link failure is detected, upon power off or upon detach.
[TS 36.331, clause 5.6.5.3]
Upon receiving the UEInformationRequest message, the UE shall:
…
1> if rlf-ReportReq is set to true and the UE has radio link failure information or handover failure information available in VarRLF-Report and if the RPLMN is included in plmn-IdentityList stored in VarRLF-Report:
2> set timeSinceFailure in VarRLF-Report to the time that elapsed since the last radio link or handover failure in E-UTRA;
2> set the rlf-Report in the UEInformationResponse message to the value of rlf-Report in VarRLF-Report;
2> discard the rlf-Report from VarRLF-Report upon successful delivery of the UEInformationResponse message confirmed by lower layers;
…
1> if the logMeasReport is included in the UEInformationResponse:
…
1> else:
2> submit the UEInformationResponse message to lower layers for transmission via SRB1;
8.6.4.8.3 Test description
8.6.4.8.3.1 Pre-test conditions
System Simulator:
– Cell 1 and 12
– System information combination 3 as defined in TS 36.508 [18] clause 4.4.3.1 is used in E-UTRA cells.
– The PLMNs are identified in the test by the identifiers in Table 8.6.4.8.3.1-1.
Table 8.6.4.8.3.1-1: PLMN identifiers
|
Cell |
PLMN name |
|
1 |
PLMN1 |
|
12 |
PLMN2 |
UE:
None.
Preamble:
– The UE is registered on PLMN1 (Cell 1) using the procedure described in TS 36.508[18] clause 4.5.2.3 except that the ATTACH ACCEPT message indicates PLMN2 in the Equivalent PLMN list as described in Table 8.6.4.8.3.3-4
– The UE is in state Generic RB Established (State 3) on Cell 1 according to [18].
– DRX is not configured
8.6.4.8.3.2 Test procedure sequence
Table 8.6.4.8.3.2-1 illustrates the downlink power levels and other changing parameters to be applied for the cells at various time instants of the test execution. Row marked "T1" and "T2" are to be applied. The exact instants on which these values shall be applied are described in the texts in this clause.
Table 8.6.4.8.3.2-1: Time instances of cell power level
|
Parameter |
Unit |
Cell 1 |
Cell 12 |
Remark |
|
|
T1 |
RS EPRE |
dBm/15kHz |
"Off" |
"Off" |
No cell is available (NOTE 1) |
|
T2 |
RS EPRE |
dBm/15kHz |
"Off" |
-85 |
(NOTE 1) |
|
NOTE 1: Power level “Off” is defined in TS 36.508 Table 6.2.2.1-1. |
|||||
Table 8.6.4.8.3.2-2: Main behaviour
|
St |
Procedure |
Message Sequence |
TP |
Verdict |
|
|
U – S |
Message |
||||
|
1 |
The SS changes Cell 1 parameter according to the row "T1" in Table 8.6.4.8.3.2-1. |
– |
– |
– |
– |
|
2 |
The SS waits for 12s to ensure that the UE detects T311 expiry. |
– |
– |
– |
– |
|
3 |
The SS changes Cell 12 parameter according to the row "T2" in Table 8.6.4.8.3.2-1. |
– |
– |
– |
– |
|
4 |
The UE transmits an RRCConnectionRequest message on cell 12 to initiate a tracking area update procedure. |
–> |
RRCConnectionRequest |
– |
– |
|
5 |
The SS transmit an RRCConnectionSetup message. |
<– |
RRCConnectionSetup |
– |
– |
|
6 |
The UE transmits an RRCConnectionSetupComplete message to confirm the successful completion of the connection establishment and a TRACKING AREA UPDATE REQUEST message is sent to update the registration of the actual tracking area. Check: Does the UE send an RRCConnectionSetupComplete message with rlf-InfoAvailable on Cell 12? |
–> |
RRCConnectionSetupComplete NAS: TRACKING AREA UPDATE REQUEST |
1 |
P |
|
7-9 |
Steps 4 to 6 of the generic test procedure in TS 36.508 subclause 6.4.2.7 are performed on Cell 12. NOTE: The UE performs a TAU procedure. The TAU is accepted with PLMN1 listed as an Equivalent PLMN and the RRC connection is released. |
– |
– |
– |
– |
|
10-18 |
Steps 1 to 9 of the generic radio bearer establishment procedure in TS 36.508 subclause 4.5.3.3 are executed to successfully complete the service request procedure on Cell 12. |
– |
– |
– |
– |
|
19 |
The SS sends a UEInformationRequest message to get rlf-ReportReq on Cell 12. |
<– |
UEInformationRequest |
– |
– |
|
20 |
Check: Does the UE send a UEInformationResponse message with rlf-Report on Cell 12? |
–> |
UEInformationResponse |
2 |
P |
8.6.4.8.3.3 Specific message contents
Table 8.6.4.8.3.3-1: RRCConnectionSetupComplete (step 6, Table 8.6.4.8.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-18 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionSetupComplete ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
rrcConnectionSetupComplete-r8 SEQUENCE { |
|||
|
nonCriticalExtension SEQUENCE { |
|||
|
nonCriticalExtension SEQUENCE { |
|||
|
rlf-InfoAvailable-r10 |
true |
||
|
nonCriticalExtension SEQUENCE {} |
Not present |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.8.3.3-1A: Message TRACKING AREA UPDATE ACCEPT (step 7, 8.6.4.8.3.2-2)
|
Derivation path: 36.508 table 4.7.2-24 |
|||
|
Information Element |
Value/Remark |
Comment |
Condition |
|
Equivalent PLMNs |
PLMN1 |
||
Table 8.6.4.8.3.3-2: UEInformationRequest (step 19, Table 8.6.4.8.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23A, condition RLF Report |
Table 8.6.4.8.3.3-3: UEInformationResponse (step 20, Table 8.6.4.8.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23B |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
RLF-Report-r9 ::= SEQUENCE { |
||||
|
measResultLastServCell-r9 SEQUENCE { |
||||
|
rsrpResult-r9 |
(0..97) |
|||
|
rsrqResult-r9 |
Not present or (0..34) |
|||
|
} |
||||
|
measResultNeighCells-r9 SEQUENCE { |
||||
|
measResultListEUTRA-r9 |
Not present |
|||
|
measResultListUTRA-r9 |
Not present |
|||
|
measResultListGERAN-r9 |
Not present |
|||
|
measResultsCDMA2000-r9 |
Not present |
|||
|
} |
||||
|
locationInfo-r10 |
Not Present or any allowed value |
|||
|
failedPCellId-r10 CHOICE { |
cellGlobalId-r10 or pci-arfcn-r10 |
If the UE has the global cell identity depending on UE implementation, the UE sets the global cell identity; otherwise the UE sets the physical cell identity and the carrier frequency. |
||
|
cellGlobalId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
} |
||||
|
pci-arfcn-r10 SEQUENCE { |
||||
|
physCellId-r10 |
Physical cell Identity of Cell 1 |
|||
|
carrierFreq-r10 |
Same downlink EARFCN as used for Cell 1 |
|||
|
carrierFreq-r10 |
maxEARFCN |
Band > 64 |
||
|
} |
||||
|
timeSinceFailure-r11 |
Any allowed value |
|||
|
} |
||||
|
failedPCellId-v1090 SEQUENCE { |
Band > 64 |
|||
|
carrierFreq-v1090 |
Not present or the same downlink EARFCN as used for Cell 1 |
|||
|
} |
||||
|
previousUTRA-CellId-r11 |
Not present |
|||
|
selectedUTRA-CellId-r11 |
Not present |
|||
|
} |
||||
|
Condition |
Explanation |
|
Band > 64 |
This condition applies if the band number is bigger than 64. |
Table 8.6.4.8.3.3-4: ATTACH ACCEPT for Cell 1 (preamble)
|
Derivation path: 36.508 Table 4.7.2-1 |
|||
|
Information Element |
Value/Remark |
Comment |
Condition |
|
Equivalent PLMNs |
PLMN2 |
||
Table 8.6.4.8.3.3-5: RRCConnectionReconfiguration (preamble)
|
Derivation path: 36.508 table 4.8.2.1.5-1 |
|||
|
Information Element |
Value/Remark |
Comment |
Condition |
|
RRCConnectionReconfiguration ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
rrcConnectionReconfiguration-r8 SEQUENCE { |
|||
|
RadioResourceConfigDedicated SEQUENCE { |
|||
|
mac-MainConfig CHOICE { |
|||
|
drx-Config |
Not present |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
8.6.4.9 Radio Link Failure logging / Logging and reporting / Reporting at intra LTE handover / PLMN list
8.6.4.9.1 Test Purpose (TP)
(1)
with { UE having completed the radio bearer establishment and initial security activation procedure }
ensure that {
when { UE performs RRC connection re-establishment procedure and intra-LTE handover procedure}
then { UE sends an RRCConnectionReconfigurationComplete message with rlf-InfoAvailable }
}
(2)
with { UE having sent an RRCConnectionReconfigurationComplete message with rlf-InfoAvailable }
ensure that {
when { UE receives a UEInformationRequest message with rlf-ReportReq set to true }
then { UE sends a UEInformationResponse message with rlf-Report and PLMN list }
}
8.6.4.9.2 Conformance requirements
References: The conformance requirements covered in the present TC are specified in: TS 36.331, clause 5.3.5.4, 5.3.11.3 and 5.6.5.3. Unless otherwise stated these are Rel-11 requirements.
[TS 36.331, clause 5.3.5.4]
If the RRCConnectionReconfiguration message includes the mobilityControlInfo and the UE is able to comply with the configuration included in this message, the UE shall:
…
1> set the content of RRCConnectionReconfigurationComplete message as follows:
2> if the UE has radio link failure or handover failure information available in VarRLF-Report and if the RPLMN is included in plmn-IdentityList stored in VarRLF-Report:
3> include rlf-InfoAvailable;
[TS 36.331, clause 5.3.11.3]
The UE shall:
1> upon T310 expiry; or
1> upon random access problem indication from MAC while neither T300, T301, T304 nor T311 is running; or
1> upon indication from RLC that the maximum number of retransmissions has been reached:
2> consider radio link failure to be detected;
2> store the following radio link failure information in the VarRLF-Report by setting its fields as follows:
3> clear the information included in VarRLF-Report, if any;
3> set the plmn-IdentityList to include the list of EPLMNs stored by the UE (i.e. includes the RPLMN);
3> set the measResultLastServCell to include the RSRP and RSRQ, if available, of the PCell based on measurements collected up to the moment the UE detected radio link failure;
3> set the measResultNeighCells to include the best measured cells, other than the PCell, ordered such that the best cell is listed first, and based on measurements collected up to the moment the UE detected radio link failure, and set its fields as follows;
4> if the UE was configured to perform measurements for one or more EUTRA frequencies, include the measResultListEUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring UTRA frequencies, include the measResultListUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring GERAN frequencies, include the measResultListGERAN;
4> if the UE was configured to perform measurement reporting for one or more neighbouring CDMA2000 frequencies, include the measResultsCDMA2000;
4> for each neighbour cell included, include the optional fields that are available;
…
3> if detailed location information is available, set the content of the locationInfo as follows:
4> include the locationCoordinates;
4> include the horizontalVelocity, if available;
3> set the failedPCellId to the global cell identity, if available, and otherwise to the physical cell identity and carrier frequency of the PCell where radio link failure is detected;
3> if an RRCConnectionReconfiguration message including the mobilityControlInfo was received before the connection failure:
4> if the last RRCConnectionReconfiguration message including the mobilityControlInfo concerned an intra E-UTRA handover:
5> include the previousPCellId and set it to the global cell identity of the PCell where the last RRCConnectionReconfiguration message including mobilityControlInfo was received;
5> set the timeConnFailure to the elapsed time since reception of the last RRCConnectionReconfiguration message including the mobilityControlInfo;
4> if the last RRCConnectionReconfiguration message including the mobilityControlInfo concerned a handover to E-UTRA from UTRA and if the UE supports Radio Link Failure Report for Inter-RAT MRO:
5> include the previousUTRA-CellId and set it to the physical cell identity, the carrier frequency and the global cell identity, if available, of the UTRA Cell in which the last RRCConnectionReconfiguration message including mobilityControlInfo was received;
5> set the timeConnFailure to the elapsed time since reception of the last RRCConnectionReconfiguration message including the mobilityControlInfo;
3> set the connectionFailureType to rlf;
3> set the c-RNTI to the C-RNTI used in the PCell;
3> set the rlf-Cause to the trigger for detecting radio link failure;
2> if AS security has not been activated:
3> perform the actions upon leaving RRC_CONNECTED as specified in 5.3.12, with release cause ‘other’;
2> else:
3> initiate the connection re-establishment procedure as specified in 5.3.7;
The UE may discard the radio link failure information, i.e. release the UE variable VarRLF-Report, 48 hours after the radio link failure is detected, upon power off or upon detach.
[TS 36.331, clause 5.6.5.3]
Upon receiving the UEInformationRequest message, the UE shall:
…
1> if rlf-ReportReq is set to true and the UE has radio link failure information or handover failure information available in VarRLF-Report and if the RPLMN is included in plmn-IdentityList stored in VarRLF-Report:
2> set timeSinceFailure in VarRLF-Report to the time that elapsed since the last radio link or handover failure in E-UTRA;
2> set the rlf-Report in the UEInformationResponse message to the value of rlf-Report in VarRLF-Report;
2> discard the rlf-Report from VarRLF-Report upon successful delivery of the UEInformationResponse message confirmed by lower layers;
…
1> if the logMeasReport is included in the UEInformationResponse:
…
1> else:
2> submit the UEInformationResponse message to lower layers for transmission via SRB1;
8.6.4.9.3 Test description
8.6.4.9.3.1 Pre-test conditions
System Simulator:
– Cell 1 and 12
– System information combination 3 as defined in TS 36.508 [18] clause 4.4.3.1 is used in E-UTRA cells.
– The PLMNs are identified in the test by the identifiers in Table 8.6.4.9.3.1-1.
Table 8.6.4.9.3.1-1: PLMN identifiers
|
Cell |
PLMN name |
|
1 |
PLMN1 |
|
12 |
PLMN2 |
UE:
None.
Preamble:
– The UE is registered on PLMN1 (Cell 1) using the procedure described in TS 36.508[18] clause 4.5.2.3 except that the ATTACH ACCEPT message indicates PLMN2 in the Equivalent PLMN list as described in Table 8.6.4.9.3.3-8.
– The UE is in state Generic RB Established (state 3) on Cell 1 according to [18].
8.6.4.9.3.2 Test procedure sequence
Table 8.6.4.9.3.2-1 illustrates the downlink power levels and other changing parameters to be applied for the cells at various time instants of the test execution. Row marked "T1", "T2" and "T3" are to be applied. The exact instants on which these values shall be applied are described in the texts in this clause.
Table 8.6.4.9.3.2-1: Time instances of cell power level
|
Parameter |
Unit |
Cell 1 |
Cell 12 |
Remark |
|
|
T1 |
RS EPRE |
dBm/15kHz |
"Off" |
"Off" |
No cell is available (NOTE 1) |
|
T2 |
RS EPRE |
dBm/15kHz |
-85 |
"Off" |
(NOTE 1) |
|
T3 |
RS EPRE |
dBm/15kHz |
-85 |
-73 |
The power level values are such that measurement results for Cell 1 (M1) and Cell 12 (M12) satisfy entry condition for event A3 (M12 > M1). |
|
NOTE 1: Power level “Off” is defined in TS 36.508 Table 6.2.2.1-1. |
|||||
Table 8.6.4.9.3.2-2: Main behaviour
|
St |
Procedure |
Message Sequence |
TP |
Verdict |
|
|
U – S |
Message |
||||
|
1 |
The SS changes Cell 1 parameter according to the row "T1" in Table 8.6.4.9.3.2-1. |
– |
– |
– |
– |
|
2 |
The SS waits for 3s to ensure that the UE detects T310 expiry. |
– |
– |
– |
– |
|
3 |
The SS changes Cell 1 parameter according to the row "T2" in Table 8.6.4.9.3.2-1. |
– |
– |
– |
– |
|
4 |
The UE transmits an RRCConnectionReestablishmentRequest message on Cell 1. |
–> |
RRCConnectionReestablishmentRequest |
– |
– |
|
5 |
The SS transmit an RRCConnectionReestablishment message. |
<– |
RRCConnectionReestablishment |
– |
– |
|
6 |
The UE transmits an RRCConnectionReestablishmentComplete message on Cell 1. |
–> |
RRCConnectionReestablishmentComplete |
– |
– |
|
7 |
The SS transmits an RRCConnectionReconfiguration message to resume existing radio bearer on Cell 1 |
<– |
RRCConnectionReconfiguration |
– |
– |
|
8 |
The UE transmits an RRCConnectionReconfigurationComplete message on Cell 1. |
–> |
RRCConnectionReconfigurationComplete |
– |
– |
|
9 |
The SS changes Cell 1 and Cell 12 parameter according to the row "T3" in Table 8.6.4.9.3.2-1. |
– |
– |
– |
– |
|
10 |
The UE transmits a MeasurementReport message on Cell 1 to report event A3 with the measured RSRP, RSRQ value for Cell 12. |
–> |
MeasurementReport |
– |
– |
|
11 |
The SS transmits an RRCConnectionReconfiguration message on Cell 1 to order the UE to perform inter frequency handover to Cell 12. |
<– |
RRCConnectionReconfiguration |
– |
– |
|
12 |
Check: Does the UE send an RRCConnectionReconfigurationComplete message with rlf-InfoAvailable on Cell 12? |
–> |
RRCConnectionReconfigurationComplete |
1 |
P |
|
13-14A |
Steps 3 to 5 of the generic test procedure in TS 36.508 subclause 6.4.2.7 are performed on Cell 12. NOTE: The UE performs a TAU procedure. The TAU is accepted with PLMN1 listed as an Equivalent PLMN. |
– |
– |
– |
– |
|
15 |
The SS sends a UEInformationRequest message to get rlf-ReportReq on Cell 12. |
<– |
UEInformationRequest |
– |
– |
|
16 |
Check: Does the UE send a UEInformationResponse message with rlf-Report on Cell 12? |
–> |
UEInformationResponse |
2 |
P |
8.6.4.9.3.3 Specific message contents
Table 8.6.4.9.3.3-0: Conditions for specific message contents
in Tables 8.6.4.9.3.3-3, 8.6.4.9.3.3-4b and 8.6.4.9.3.3-7
|
Condition |
Explanation |
|
Band > 64 |
This condition applies if the band number is bigger than 64. |
|
Band 24 High range |
If Band 24 high frequency range is selected for the target cell |
Table 8.6.4.9.3.3-1: RRCConnectionReestablishmentRequest (step 4, Table 8.6.4.9.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-13 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishmentRequest ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
rrcConnectionReestablishmentRequest-r8 SEQUENCE { |
|||
|
ue-Identity SEQUENCE { |
|||
|
c-RNTI |
the value of the C-RNTI of the UE |
||
|
physCellId |
PhysicalCellIdentity of Cell 1 |
||
|
shortMAC-I |
The same value as the 16 least significant bits of the XMAC-I value calculated by SS |
||
|
} |
|||
|
reestablishmentCause |
otherFailure |
||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.9.3.3-2: RRCConnectionReconfiguration (step 7, Table 8.6.4.9.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-8, condition MEAS |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReconfiguration ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
rrcConnectionReconfiguration-r8 SEQUENCE { |
|||
|
radioResourceConfigDedicated |
RadioResourceConfigDedicated-HO |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.9.3.3-3: MeasConfig (step 7, Table 8.6.4.9.3.2-2)
|
Derivation Path: 36.508, Table 4.6.6-1, condition INTER-FREQ |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MeasConfig ::= SEQUENCE { |
|||
|
measObjectToAddModList SEQUENCE (SIZE (1..maxObjectId)) OF SEQUENCE { |
2 entries |
||
|
measObjectId[1] |
IdMeasObject-f1 |
||
|
measObject[1] |
MeasObjectEUTRA-GENERIC(f1) |
||
|
measObect[1] |
MeasObjectEUTRA-GENERIC(maxEARFCN) |
Band > 64 |
|
|
measObjectId[2] |
IdMeasObject-f2 |
||
|
measObject[2] |
MeasObjectEUTRA-GENERIC(f2) |
||
|
measObect[2] |
MeasObjectEUTRA-GENERIC(maxEARFCN) |
Band > 64 |
|
|
} |
|||
|
reportConfigToAddModList SEQUENCE (SIZE (1..maxReportConfigId)) OF SEQUENCE { |
1 entry |
||
|
reportConfigId[1] |
IdReportConfig-A3 |
||
|
reportConfig[1] |
ReportConfigEUTRA-A3 |
||
|
} |
|||
|
measIdToAddModListSEQUENCE (SIZE (1..maxMeasId)) OF SEQUENCE { |
|||
|
measId[1] |
1 |
||
|
measObjectId[1] |
IdMeasObject-f2 |
||
|
reportConfigId[1] |
IdReportConfig-A3 |
||
|
} |
|||
|
measObjectToAddModList-v9e0 SEQUENCE (SIZE (1..maxObjectId)) OF SEQUENCE { |
Band > 64 |
||
|
measObjectEUTRA-v9e0[1] SEQUENCE { |
|||
|
carrierFreq-v9e0 |
Same downlink EARFCN as used for f1 |
||
|
} |
|||
|
measObjectEUTRA-v9e0[2] SEQUENCE { |
|||
|
carrierFreq-v9e0 |
Same downlink EARFCN as used for f2 |
||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.9.3.3-4: MeasurementReport (step 10, Table 8.6.4.9.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-5 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MeasurementReport ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
measurementReport-r8 SEQUENCE { |
|||
|
measResults SEQUENCE { |
|||
|
measId |
1 |
||
|
measResultPCell SEQUENCE { |
|||
|
rsrpResult |
(0..97) |
||
|
rsrqResult |
(0..34) |
||
|
} |
|||
|
measResultNeighCells CHOICE { |
|||
|
measResultListEUTRA SEQUENCE (SIZE (1..maxCellReport)) OF SEQUENCE { |
1 entry |
||
|
physCellId[1] |
PhysicalCellIdentity of Cell 12 |
||
|
cgi-Info[1] |
Not present |
||
|
measResult[1] SEQUENCE { |
|||
|
rsrpResult |
(0..97) |
||
|
rsrqResult |
(0..34) |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.9.3.3-4a: RRCConnectionReconfiguration (step 11, Table 8.6.4.9.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-8, condition HO |
Table 8.6.4.9.3.3-4b: MobilityControlInfo (Table 8.6.4.9.3.3-4a)
|
Derivation Path: 36.508, Table 4.6.5-1 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
MobilityControlInfo ::= SEQUENCE { |
|||
|
targetPhysCellId |
PhysicalCellIdentity of Cell 12 |
||
|
carrierFreq SEQUENCE { |
|||
|
dl-CarrierFreq |
Same downlink EARFCN as used for Cell 12 |
||
|
ul-CarrierFreq |
Not present |
||
|
Same uplink EARFCN as used for Cell 12 |
Band 24 High range |
||
|
} |
|||
|
carrierFreq SEQUENCE {} |
Not present |
Band > 64 |
|
|
carrierFreq-v9e0 SEQUENCE { |
Band > 64 |
||
|
dl-CarrierFreq-v9e0 |
Same downlink EARFCN as used for Cell 12 |
||
|
} |
|||
|
} |
|||
Table 8.6.4.9.3.3-5: RRCConnectionReconfigulationComplete (step 12, Table 8.6.4.9.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-9 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReconfigulationComplete ::= SEQUENCE { |
|||
|
criticalExtensions SEQUENCE{ |
|||
|
rrcConnectionReconfigulationComplete-r8 SEQUENCE { |
|||
|
nonCriticalExtension SEQUENCE { |
|||
|
nonCriticalExtension SEQUENCE { |
|||
|
rlf-InfoAvailable-r10 |
true |
||
|
nonCriticalExtension SEQUENCE {} |
Not present |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.9.3.3-5A: Message TRACKING AREA UPDATE ACCEPT (step 14, 8.6.4.9.3.2-2)
|
Derivation path: 36.508 table 4.7.2-24 |
|||
|
Information Element |
Value/Remark |
Comment |
Condition |
|
Equivalent PLMNs |
PLMN1 |
||
Table 8.6.4.9.3.3-6: UEInformationRequest (step 15, Table 8.6.4.9.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23A, condition RLF Report |
Table 8.6.4.9.3.3-7: UEInformationResponse (step 16, Table 8.6.4.9.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23B |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
UEInformationResponse-r9 ::=SEQUENCE { |
||||
|
criticalExtensions CHOICE { |
||||
|
c1 CHOICE { |
||||
|
ueInformationResponse-r9 SEQUENCE { |
||||
|
rlf-Report-r9 SEQUENCE { |
||||
|
measResultLastServCell-r9 SEQUENCE { |
||||
|
rsrpResult-r9 |
(0..97) |
|||
|
rsrqResult-r9 |
Not present or (0..34) |
|||
|
} |
||||
|
measResultNeighCells-r9 SEQUENCE { |
||||
|
measResultListEUTRA-r9 |
Not present |
|||
|
measResultListUTRA-r9 |
Not present |
|||
|
measResultListGERAN-r9 |
Not present |
|||
|
measResultsCDMA2000-r9 |
Not present |
|||
|
} |
||||
|
locationInfo-r10 |
Not Present or any allowed value |
|||
|
failedPCellId-r10 CHOICE { |
cellGlobalId-r10 or pci-arfcn-r10 |
If the UE has the global cell identity depending on UE implementation, the UE sets the global cell identity; otherwise the UE sets the physical cell identity and the carrier frequency. |
||
|
cellGlobalId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
} |
||||
|
pci-arfcn-r10 SEQUENCE { |
||||
|
physCellId-r10 |
Physical cell Identity of Cell 1 |
|||
|
carrierFreq-r10 |
Same downlink EARFCN as used for Cell 1 |
|||
|
carrierFreq-r10 |
maxEARFCN |
Band > 64 |
||
|
} |
||||
|
reestablishmentCellId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
} |
||||
|
timeConnFailure-r10 |
Not present |
|||
|
connectionFailureType-r10 |
rlf |
|||
|
previousPCellId-r10 |
Not present |
|||
|
failedPCellId-v1090 SEQUENCE { |
Band > 64 |
|||
|
carrierFreq-v1090 |
Not present or the same downlink EARFCN as used for Cell 1 |
|||
|
} |
||||
|
basicFields-r11SEQUENCE { |
||||
|
c-RNTI-r11 |
Any allowed value |
|||
|
rlf-Cause-r11 |
t310-Expiry |
|||
|
timeSinceFailure-r11 |
Any allowed value |
|||
|
} |
||||
|
previousUTRA-CellId-r11 |
Not present |
|||
|
selectedUTRA-CellId-r11 |
Not present |
|||
|
} |
||||
|
} |
||||
|
} |
||||
Table 8.6.4.9.3.3-8: ATTACH ACCEPT for Cell 1 (preamble)
|
Derivation path: 36.508 Table 4.7.2-1 |
|||
|
Information Element |
Value/Remark |
Comment |
Condition |
|
Equivalent PLMNs |
PLMN2 |
||
8.6.4.10 Radio Link Failure logging / Logging and reporting / Reporting at RRC connection re-establishment / PLMN list
8.6.4.10.1 Test Purpose (TP)
(1)
with { UE having completed the radio bearer establishment and initial security activation procedure }
ensure that {
when { UE detects T310 is expired and performs RRC Connection re-establishment procedure on a cell belonging to equivalent PLMN }
then { UE sends an RRCConnectionReestablishmentComplete message with rlf-InfoAvailable }
}
(2)
with { UE having sent an RRCConnectionReestablishmentComplete message with rlf-InfoAvailable }
ensure that {
when { UE receives a UEInformationRequest message with rlf-ReportReq set to true }
then { UE sends a UEInformationResponse message with rlf-Report and PLMN list }
}
8.6.4.10.2 Conformance requirements
References: The conformance requirements covered in the present TC are specified in: TS 36.331, clause 5.3.7.5, 5.3.11.3 and 5.6.5.3. Unless otherwise stated these are Rel-11 requirements.
[TS 36.331, clause 5.3.7.5]
The UE shall:
…
1> set the content of RRCConnectionReestablishmentComplete message as follows:
2> if the UE has radio link failure or handover failure information available in VarRLF-Report and if the RPLMN is included in plmn-IdentityList stored in VarRLF-Report:
3> include the rlf-InfoAvailable;
[TS 36.331, clause 5.3.11.3]
The UE shall:
1> upon T310 expiry; or
1> upon random access problem indication from MAC while neither T300, T301, T304 nor T311 is running; or
1> upon indication from RLC that the maximum number of retransmissions has been reached:
2> consider radio link failure to be detected;
2> store the following radio link failure information in the VarRLF-Report by setting its fields as follows:
3> clear the information included in VarRLF-Report, if any;
3> set the plmn-IdentityList to include the list of EPLMNs stored by the UE (i.e. includes the RPLMN);
3> set the measResultLastServCell to include the RSRP and RSRQ, if available, of the PCell based on measurements collected up to the moment the UE detected radio link failure;
3> set the measResultNeighCells to include the best measured cells, other than the PCell, ordered such that the best cell is listed first, and based on measurements collected up to the moment the UE detected radio link failure, and set its fields as follows;
4> if the UE was configured to perform measurements for one or more EUTRA frequencies, include the measResultListEUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring UTRA frequencies, include the measResultListUTRA;
4> if the UE was configured to perform measurement reporting for one or more neighbouring GERAN frequencies, include the measResultListGERAN;
4> if the UE was configured to perform measurement reporting for one or more neighbouring CDMA2000 frequencies, include the measResultsCDMA2000;
4> for each neighbour cell included, include the optional fields that are available;
…
3> if detailed location information is available, set the content of the locationInfo as follows:
4> include the locationCoordinates;
4> include the horizontalVelocity, if available;
3> set the failedPCellId to the global cell identity, if available, and otherwise to the physical cell identity and carrier frequency of the PCell where radio link failure is detected;
3> if an RRCConnectionReconfiguration message including the mobilityControlInfo was received before the connection failure:
4> if the last RRCConnectionReconfiguration message including the mobilityControlInfo concerned an intra E-UTRA handover:
5> include the previousPCellId and set it to the global cell identity of the PCell where the last RRCConnectionReconfiguration message including mobilityControlInfo was received;
5> set the timeConnFailure to the elapsed time since reception of the last RRCConnectionReconfiguration message including the mobilityControlInfo;
4> if the last RRCConnectionReconfiguration message including the mobilityControlInfo concerned a handover to E-UTRA from UTRA and if the UE supports Radio Link Failure Report for Inter-RAT MRO:
5> include the previousUTRA-CellId and set it to the physical cell identity, the carrier frequency and the global cell identity, if available, of the UTRA Cell in which the last RRCConnectionReconfiguration message including mobilityControlInfo was received;
5> set the timeConnFailure to the elapsed time since reception of the last RRCConnectionReconfiguration message including the mobilityControlInfo;
3> set the connectionFailureType to rlf;
3> set the c-RNTI to the C-RNTI used in the PCell;
3> set the rlf-Cause to the trigger for detecting radio link failure;
2> if AS security has not been activated:
3> perform the actions upon leaving RRC_CONNECTED as specified in 5.3.12, with release cause ‘other’;
2> else:
3> initiate the connection re-establishment procedure as specified in 5.3.7;
The UE may discard the radio link failure information, i.e. release the UE variable VarRLF-Report, 48 hours after the radio link failure is detected, upon power off or upon detach.
[TS 36.331, clause 5.6.5.3]
Upon receiving the UEInformationRequest message, the UE shall:
…
1> if rlf-ReportReq is set to true and the UE has radio link failure information or handover failure information available in VarRLF-Report and if the RPLMN is included in plmn-IdentityList stored in VarRLF-Report:
2> set timeSinceFailure in VarRLF-Report to the time that elapsed since the last radio link or handover failure in E-UTRA;
2> set the rlf-Report in the UEInformationResponse message to the value of rlf-Report in VarRLF-Report;
2> discard the rlf-Report from VarRLF-Report upon successful delivery of the UEInformationResponse message confirmed by lower layers;
…
1> if the logMeasReport is included in the UEInformationResponse:
…
1> else:
2> submit the UEInformationResponse message to lower layers for transmission via SRB1;
8.6.4.10.3 Test description
8.6.4.10.3.1 Pre-test conditions
System Simulator:
– Cell 1 and 12
– System information combination 3 as defined in TS 36.508 [18] clause 4.4.3.1 is used in E-UTRA cells.
– The PLMNs are identified in the test by the identifiers in Table 8.6.4.8.3.1-1.
Table 8.6.4.10.3.1-1: PLMN identifiers
|
Cell |
PLMN name |
|
1 |
PLMN1 |
|
12 |
PLMN2 |
UE:
None.
Preamble:
– The UE is registered on PLMN1 (Cell 1) using the procedure described in TS 36.508[18] clause 4.5.2.3 except that the ATTACH ACCEPT message indicates PLMN2 in the Equivalent PLMN list as described in Table 8.6.4.10.3.3-4
– The UE is in state Generic RB Established (state 3) on Cell 1 according to [18].
8.6.4.10.3.2 Test procedure sequence
Table 8.6.4.8.3.2-1 illustrates the downlink power levels and other changing parameters to be applied for the cells at various time instants of the test execution. Row marked "T1" and "T2" are to be applied. The exact instants on which these values shall be applied are described in the texts in this clause.
Table 8.6.4.10.3.2-1: Time instances of cell power level
|
Parameter |
Unit |
Cell 1 |
Cell 12 |
Remark |
|
|
T1 |
RS EPRE |
dBm/15kHz |
-85 |
-91 |
|
|
T2 |
RS EPRE |
dBm/15kHz |
"Off" |
-85 |
(NOTE 1) |
|
NOTE 1: Power level “Off” is defined in TS 36.508 Table 6.2.2.1-1. |
|||||
Table 8.6.4.10.3.2-2: Main behaviour
|
St |
Procedure |
Message Sequence |
TP |
Verdict |
|
|
U – S |
Message |
||||
|
1 |
The SS changes cell parameters according to the row "T1" in Table 8.6.4.10.3.2-1. |
– |
– |
– |
– |
|
2 |
The SS waits for 60s to ensure that the UE detects the present of Cell12. |
– |
– |
– |
– |
|
3 |
The SS changes cell parameters according to the row "T2" in Table 8.6.4.10.3.2-1. |
– |
– |
– |
– |
|
4 |
The UE transmits an RRCConnectionReestablishmentRequest message on Cell 12. |
–> |
RRCConnectionReestablishmentRequest |
– |
– |
|
5 |
The SS transmit an RRCConnectionReestablishment message. |
<– |
RRCConnectionReestablishment |
– |
– |
|
6 |
Check: Does the UE send an RRCConnectionReestablishmentComplete message with rlf-InfoAvailable on Cell 12? |
–> |
RRCConnectionReestablishmentComplete |
1 |
P |
|
7 |
The SS transmits an RRCConnectionReconfiguration message to resume existing radio bearer on Cell 12 |
<– |
RRCConnectionReconfiguration |
– |
– |
|
8 |
The UE transmits an RRCConnectionReconfigurationComplete message on Cell 12. |
–> |
RRCConnectionReconfigurationComplete |
– |
– |
|
8A |
The UE transmits a Tracking Area Update Request message on Cell 12. |
–> |
NAS: TRACKING AREA UPDATE REQUEST |
– |
– |
|
8B |
The SS transmits a Tracking Area Update Accept Note: The TAU is accepted with PLMN1 listed as an Equivalent PLMN. |
<– |
NAS: TRACKING AREA UPDATE ACCEPT |
– |
– |
|
8C |
The UE transmits a Tracking Area Update Complete |
–> |
NAS: TRACKING AREA UPDATE COMPLETE |
– |
– |
|
9 |
The SS sends a UEInformationRequest message to get rlf-ReportReq on Cell 12. |
<– |
UEInformationRequest |
– |
– |
|
10 |
Check: Does the UE send a UEInformationResponse message with rlf-Report on Cell 12? |
–> |
UEInformationResponse |
2 |
P |
8.6.4.10.3.3 Specific message contents
Table 8.6.4.10.3.3-1: RRCConnectionReestablishmentComplete (step 6, Table 8.6.4.10.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-11 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishmentComplete ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE{ |
|||
|
rrcConnectionReestablishmentComplete-r8 SEQUENCE { |
|||
|
nonCriticalExtension SEQUENCE { |
|||
|
rlf-InfoAvailable-r9 |
true |
||
|
nonCriticalExtension SEQUENCE {} |
Not present |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.10.3.3-1A: Message TRACKING AREA UPDATE ACCEPT (step 8B, 8.6.4.10.3.2-2)
|
Derivation path: 36.508 table 4.7.2-24 |
|||
|
Information Element |
Value/Remark |
Comment |
Condition |
|
Equivalent PLMNs |
PLMN1 |
||
Table 8.6.4.10.3.3-2: UEInformationRequest (step 9, Table 8.6.4.10.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23A, condition RLF |
Table 8.6.4.10.3.3-3: UEInformationResponse (step 10, Table 8.6.4.10.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23B |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
UEInformationResponse-r9 ::=SEQUENCE { |
||||
|
criticalExtensions CHOICE { |
||||
|
c1 CHOICE { |
||||
|
ueInformationResponse-r9 SEQUENCE { |
||||
|
RLF-Report-r9 ::= SEQUENCE { |
||||
|
measResultLastServCell-r9 SEQUENCE { |
||||
|
rsrpResult-r9 |
(0..97) |
|||
|
rsrqResult-r9 |
Not present or (0..34) |
|||
|
} |
||||
|
measResultNeighCells-r9 SEQUENCE { |
||||
|
measResultListEUTRA-r9 |
Not present |
|||
|
measResultListUTRA-r9 |
Not present |
|||
|
measResultListGERAN-r9 |
Not present |
|||
|
measResultsCDMA2000-r9 |
Not present |
|||
|
} |
||||
|
locationInfo-r10 |
Not Present or any allowed value |
|||
|
failedPCellId-r10 CHOICE { |
cellGlobalId-r10 or pci-arfcn-r10 |
If the UE has the global cell identity depending on UE implementation, the UE sets the global cell identity; otherwise the UE sets the physical cell identity and the carrier frequency. |
||
|
cellGlobalId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
} |
||||
|
pci-arfcn-r10 SEQUENCE { |
||||
|
physCellId-r10 |
Physical cell Identity of Cell 1 |
|||
|
carrierFreq-r10 |
Same downlink EARFCN as used for Cell 1 |
|||
|
carrierFreq-r10 |
maxEARFCN |
Band > 64 |
||
|
} |
||||
|
reestablishmentCellId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 12 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 12 |
|||
|
} |
||||
|
connectionFailureType-r10 |
rlf |
|||
|
previousPCellId-r10 |
Not present or any allowed value |
|||
|
failedPCellId-v1090 SEQUENCE { |
Band > 64 |
|||
|
carrierFreq-v1090 |
Not present or the same downlink EARFCN as used for Cell 1 |
|||
|
} |
||||
|
basicFields-r11SEQUENCE { |
||||
|
c-RNTI-r11 |
Any allowed value |
|||
|
rlf-Cause-r11 |
t310-Expiry |
|||
|
timeSinceFailure-r11 |
Any allowed value |
|||
|
} |
||||
|
previousUTRA-CellId-r11 |
Not present |
|||
|
selectedUTRA-CellId-r11 |
Not present |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
Condition |
Explanation |
|
Band > 64 |
This condition applies if the band number is bigger than 64. |
Table 8.6.4.10.3.3-4: ATTACH ACCEPT for Cell 1 (preamble)
|
Derivation path: 36.508 Table 4.7.2-1 |
|||
|
Information Element |
Value/Remark |
Comment |
Condition |
|
Equivalent PLMNs |
PLMN2 |
||
8.6.4.11 Radio Link Failure logging / Logging and reporting / Dropped QCI
8.6.4.11.1 Test Purpose (TP)
(1)
with { UE in RRC_CONNECTED state having a DRB with QCI1 and detecting radio link failure }
ensure that {
when { UE has radio link failure information available in VarRLF-Report and plmn-Identity stored in VarRLF-Report is equal to the RPLMN }
then { UE sends the RRCConnectionReestablishmentComplete message with rlf-InfoAvailable included
}
}
(2)
with { UE in RRC_CONNECTED having a DRB with QCI1 and reported that the UE has radio link failure information available }
ensure that {
when { UE receives the UEInformationRequest message containing rlf-ReportReq }
then { UE sends the UEInformationResponse message with rlf-Report included with IE drb-EstablishedWithQCI-1-r13}
}
8.6.4.11.2 Conformance requirements
References: The conformance requirements covered in the present TC are specified in: TS 36.331, clause 5.3.7.4, 5.3.7.5, 5.3.11.3 and 5.6.5.3.
[TS 36.331, clause 5.3.7.4]
Except for NB-IoT, if the procedure was initiated due to radio link failure or handover failure, the UE shall:
1> set the reestablishmentCellId in the VarRLF-Report to the global cell identity of the selected cell;
[TS 36.331, clause 5.3.7.5]
The UE shall:
…
1> if the UE is not a NB-IoT UE:
2> set the content of RRCConnectionReestablishmentComplete message as follows:
3> if the UE has radio link failure or handover failure information available in VarRLF-Report and if the RPLMN is included in plmn-IdentityList stored in VarRLF-Report:
4> include the rlf-InfoAvailable;
[TS 36.331, clause 5.3.11.3]
The UE shall:
1> upon T310 expiry; or
1> upon T312 expiry; or
1> upon random access problem indication from MCG MAC while neither T300, T301, T304 nor T311 is running; or
1> upon indication from MCG RLC that the maximum number of retransmissions has been reached for an SRB or for an MCG or split DRB:
2> consider radio link failure to be detected for the MCG i.e. RLF;
2> except for NB-IoT, store the following radio link failure information in the VarRLF-Report by setting its fields as follows:
3> clear the information included in VarRLF-Report, if any;
3> set the plmn-IdentityList to include the list of EPLMNs stored by the UE (i.e. includes the RPLMN);
…
3> if the UE supports QCI1 indication in Radio Link Failure Report and has a DRB for which QCI is 1:
4> include the drb-EstablishedWithQCI-1;
3> set the connectionFailureType to rlf;
3> set the c-RNTI to the C-RNTI used in the PCell;
3> set the rlf-Cause to the trigger for detecting radio link failure;
[TS 36.331, clause 5.6.5.3]
Upon receiving the UEInformationRequest message, the UE shall, only after successful security activation:
…
1> if rlf-ReportReq is set to true and the UE has radio link failure information or handover failure information available in VarRLF-Report and if the RPLMN is included in plmn-IdentityList stored in VarRLF-Report:
2> set timeSinceFailure in VarRLF-Report to the time that elapsed since the last radio link or handover failure in E-UTRA;
2> set the rlf-Report in the UEInformationResponse message to the value of rlf-Report in VarRLF-Report;
2> discard the rlf-Report from VarRLF-Report upon successful delivery of the UEInformationResponse message confirmed by lower layers;
…
1> else:
2> submit the UEInformationResponse message to lower layers for transmission via SRB1;
8.6.4.11.3 Test description
8.6.4.11.3.1 Pre-test conditions
System Simulator:
-Cell 1 and Cell 2
UE:
None.
Preamble:
– The UE is in state Registered, Idle mode (state 2) on Cell 1 according to [18]
8.6.4.11.3.2 Test procedure sequence
Table 8.6.4.11.3.2-1 illustrates the downlink power levels and other changing parameters to be applied for the cells at various time instants of the test execution. Row marked "T0" denotes the initial conditions after preamble, while columns marked "T1" is to be applied subsequently. The exact instants on which these values shall be applied are described in the texts in this clause.
Table 8.6.4.11.3.2-1: Time instances of cell power level and parameter changes
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
Remark |
|
|
T0 |
Cell-specific RS EPRE |
dBm/15kHz |
-85 |
"Off" |
Only Cell 1 is available. (NOTE 1) |
|
T1 |
Cell-specific RS EPRE |
dBm/15kHz |
"Off" |
-79 |
Only Cell 2 is available. (NOTE 1) |
|
NOTE 1: Power level “Off” is defined in TS 36.508 Table 6.2.2.1-1. |
|||||
Table 8.6.4.11.3.2-2: Main behaviour
|
St |
Procedure |
Message Sequence |
TP |
Verdict |
|
|
U – S |
Message |
||||
|
1-14 |
Steps 1 to 14 of the generic test procedure for IMS MO speech call (TS 36.508 4.5A.6.3-1). |
– |
– |
– |
– |
|
15 |
The SS changes Cell 1 and Cell 2 parameters according to the row "T1" in Table 8.6.4.11.3.2-1 in order that the radio link quality of Cell 1 is degraded and Cell 2 is suitable for camping. |
– |
– |
– |
– |
|
16 |
The UE transmits an RRCConnectionReestablishmentRequest message on Cell 2. |
–> |
RRCConnectionReestablishmentRequest |
– |
– |
|
17 |
The SS transmits an RRCConnectionReestablishment message on Cell 2. |
<– |
RRCConnectionReestablishment |
– |
– |
|
18 |
The UE transmits an RRCConnectionReestablishmentComplete message on Cell 2 including the IE rlf-InfoAvailable. |
–> |
RRCConnectionReestablishmentComplete |
1 |
P |
|
19 |
The SS transmits a UEInformationRequest message on Cell 2. |
<– |
UEInformationRequest |
– |
– |
|
20 |
Check: Does the UE transmit a UEInformationResponse message on Cell 2 including IE drb-EstablishedWithQCI-1-r13? |
–> |
UEInformationResponse |
2 |
P |
8.6.4.11.3.3 Specific message contents
Table 8.6.4.11.3.3-1: RRCConnectionReestablishmentRequest (step 16, Table 8.6.4.11.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-13 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishmentRequest ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
rrcConnectionReestablishmentRequest-r8 SEQUENCE { |
|||
|
ue-Identity SEQUENCE { |
|||
|
c-RNTI |
the value of the C-RNTI of the UE |
||
|
physCellId |
PhysicalCellIdentity of Cell 1 |
||
|
shortMAC-I |
The same value as the 16 least significant bits of the XMAC-I value calculated by SS |
||
|
} |
|||
|
reestablishmentCause |
otherFailure |
||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.11.3.3-2: RRCConnectionReestablishmentComplete (step 18, Table 8.6.4.11.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-11 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCConnectionReestablishmentComplete ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
rrcConnectionReestablishmentComplete-r8 = SEQUENCE { |
|||
|
nonCriticalExtension SEQUENCE { |
|||
|
rlf-InfoAvailable-r9 |
True |
||
|
nonCriticalExtension |
Not present or any allowed value |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.11.3.3-3: UEInformationRequest (step 19, Table 8.6.4.11.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23A |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
UEInformationRequest-r9 ::=SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
c1 CHOICE { |
|||
|
ueInformationRequest-r9 SEQUENCE { |
|||
|
rlf-ReportReq-r9 |
True |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 8.6.4.11.3.3-4: UEInformationResponse (step 20, Table 8.6.4.11.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-23B |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
UEInformationResponse-r9 ::=SEQUENCE { |
||||
|
criticalExtensions CHOICE { |
||||
|
c1 CHOICE { |
||||
|
ueInformationResponse-r9 SEQUENCE { |
||||
|
rlf-Report-r9 SEQUENCE { |
||||
|
measResultLastServCell-r9 SEQUENCE { |
||||
|
rsrpResult-r9 |
(0..97) |
|||
|
rsrqResult-r9 |
Not present or (0..34) |
|||
|
} |
||||
|
measResultNeighCells-r9 SEQUENCE { |
||||
|
measResultListEUTRA-r9 |
Not present |
|||
|
measResultListUTRA-r9 |
Not present |
|||
|
measResultListGERAN-r9 |
Not present |
|||
|
measResultsCDMA2000-r9 |
Not present |
|||
|
} |
||||
|
locationInfo-r10 |
Not present or any allowed value |
|||
|
failedPCellId-r10 CHOICE { |
cellGlobalId-r10 or pci-arfcn-r10 |
If the UE has the global cell identity depending on UE implementation, the UE sets the global cell identity, otherwise the UE sets the physical cell identity and the carrier frequency. |
||
|
cellGlobalId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 1 |
|||
|
} |
||||
|
pci-arfcn-r10 SEQUENCE { |
||||
|
physCellId-r10 |
Physical cell Identity of Cell 1 |
|||
|
carrierFreq-r10 |
Same downlink EARFCN as used for Cell 1 |
|||
|
carrierFreq-r10 |
maxEARFCN |
Band > 64 |
||
|
} |
||||
|
} |
||||
|
reestablishmentCellId-r10 SEQUENCE { |
||||
|
plmn-Identity |
plmn-Identity within SystemInformationBlockType1 broadcasted in Cell 2 |
|||
|
cellIdentity |
cellIdentity within SystemInformationBlockType1 broadcasted in Cell 2 |
|||
|
} |
||||
|
timeConnFailure-r10 |
Not present |
|||
|
connectionFailureType-r10 |
rlf |
|||
|
previousPCellId-r10 |
Not present |
|||
|
failedPCellId-v1090 SEQUENCE { |
Band > 64 |
|||
|
carrierFreq-v1090 |
Same downlink EARFCN as used for Cell 1 |
|||
|
} |
||||
|
basicFields-r11 SEQUENCE { |
||||
|
c-RNTI-r11 |
Any allowed value |
|||
|
rlf-Cause-r11 |
Any allowed value |
|||
|
timeSinceFailure-r11 |
Any allowed value |
|||
|
} |
||||
|
previousUTRA-CellId-r11 |
Not present |
|||
|
selectedUTRA-CellId-r11 |
Not present |
|||
|
drb-EstablishedWithQCI-1-r13 |
qci1 |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
Condition |
Explanation |
|
Band > 64 |
This condition applies if the band number is bigger than 64. |