24.1.17 V2X Sidelink Communication / Pre-configured authorisation / UE in RRC_IDLE on an E-UTRAN cell operating on the anchor carrier frequency provisioned for V2X configuration / UE uses Tx resource pool which is associated with the synchronization reference source selected
36.523-13GPPEvolved Universal Terrestrial Radio Access (E-UTRA) and Evolved Packet Core (EPC)Part 1: Protocol conformance specificationRelease 17TSUser Equipment (UE) conformance specification
24.1.1.17 Test Purpose (TP)
(1)
with { UE supporting V2X sidelink communication }
ensure that {
when { UE is triggered by an upper layer application to transmit V2X sidelink communication }
then { UE shall only use the pool which is associated with the synchronization reference source selected }
}
24.1.17.2 Conformance requirements
References: The conformance requirements covered in the current TC are specified in: TS 36.331, clauses 5.10.13.2.
[TS 36.331, clause 5.10.13.2]
For a frequency used for V2X sidelink communication, if zoneConfig is not ignored as specified in 5.10.13.1, the UE configured by upper layers for V2X sidelink communication shall only use the pool which corresponds to geographical coordinates of the UE, if zoneConfig is included in SystemInformationBlockType21 of the serving cell (RRC_IDLE)/ PCell (RRC_CONNECTED) or in RRCConnectionReconfiguration for the concerned frequency, and the UE is configured to use resource pools provided by RRC signalling for the concerned frequency; or if zoneConfig is included in SL-V2X-Preconfiguration for the concerned frequency, and the UE is configured to use resource pools in SL-V2X-Preconfiguration for the frequency, according to 5.10.13.1. The UE shall only use the pool which is associated with the synchronization reference source selected in accordance with 5.10.8.2.
1> if the UE is configured to transmit on p2x-CommTxPoolNormalCommon or on p2x-CommTxPoolNormal in v2x-InterFreqInfoList in SystemInformationBlockType21 according to 5.10.13.1; or
1> if the UE is configured to transmit on p2x-CommTxPoolList-r14 in SL-V2X-Preconfiguration according to 5.10.13.1; or
1> if zoneConfig is not included in SystemInformationBlockType21 and the UE is configured to transmit on v2x-CommTxPoolNormalCommon or v2x-CommTxPoolNormalDedicated; or
1> if zoneConfig is included in SystemInformationBlockType21 and the UE is configured to transmit on v2x-CommTxPoolNormalDedicated for P2X related V2X sidelink communication and zoneID is not included in v2x-CommTxPoolNormalDedicated; or
1> if zoneConfig is not included in the entry of v2x-InterFreqInfoList for the concerned frequency and the UE is configured to transmit on v2x-CommTxPoolNormal in v2x-InterFreqInfoList or p2x-CommTxPoolNormal in v2x-InterFreqInfoList in RRCConnectionReconfiguration; or
1> if zoneConfig is not included in SL-V2X-Preconfiguration for the concerned frequency and the UE is configured to transmit on v2x-CommTxPoolList in SL-V2X-Preconfiguration for the concerned frequency:
2> select the first pool associated with the synchronization reference source selected in accordance with 5.10.8.2;
1> if zoneConfig is included in SystemInformationBlockType21 and the UE is configured to transmit on v2x-CommTxPoolNormalCommon or v2x-CommTxPoolNormalDedicated for non-P2X related V2X sidelink communication; or
1> if zoneConfig is included in SystemInformationBlockType21 and the UE is configured to transmit on v2x-CommTxPoolNormalDedicated for P2X related V2X sidelink communication and zoneID is included in v2x-CommTxPoolNormalDedicated; or
1> if zoneConfig is included in the entry of v2x-InterFreqInfoList for the concerned frequency and the UE is configured to transmit on v2x-CommTxPoolNormal in v2x-InterFreqInfoList or p2x-CommTxPoolNormal in v2x-InterFreqInfoList in RRCConnectionReconfiguration; or
1> if zoneConfig is included in SL-V2X-Preconfiguration for the concerned frequency and the UE is configured to transmit on v2x-CommTxPoolList in SL-V2X-Preconfiguration for the concerned frequency:
2> select the pool configured with zoneID equal to the zone identity determined below and associated with the synchronization reference source selected in accordance with 5.10.8.2;
24.1.17.3 Test description
24.1.17.3.1 Pre-test conditions
System Simulator:
SS-NW
– Cell 1
Table 24.1.17.3.1-1: Cell parameters values
|
Cell |
Frequency |
PLMN |
|
1 |
f1 |
HPLMN (PLMN1) |
|
Note 1: The Frequency f1 shall be the anchor frequency pre-configured in the UE/USIM. |
||
– System information combination 29 as defined in TS 36.508 [18] clause 4.4.3.1 is used in all active cells.
– 1 GNSS simulator
UE:
– V2X sidelink related configuration..
– The UE is authorised to perform V2X Sidelink Communication
– The UE is equipped with below information in UE or in a USIM containing default values (as per TS 36.508 [18]) except for those listed in Table 24.1.17.3.1-2.
Table 24.1.17.3.1-2: UE/ USIM configuration
|
USIM field |
Priority |
Value |
Access Technology Identifier |
|
EFUST |
Service n°119 (V2X) supported |
||
|
EFVST |
As per TS 36.508 [18] clause 4.9.3.4 |
||
|
EFV2X_CONFIG |
SL-V2X-Preconfiguration field as defined in Table 24.1.17.3.3-4 |
Preamble:
– The UE is registered, Idle Mode, UE Test Mode E Activated (state 2A) according to TS 36.508 [18] on Cell 1.
24.1.17.3.2 Test procedure sequence
Table 24.1.17.3.2-1: Main behaviour
|
St |
Procedure |
Message Sequence |
TP |
Verdict |
|
|
U – S |
Message |
||||
|
0 |
Trigger the UE to reset UTC time. NOTE: The UTC time reset may be performed by MMI or AT command (+CUTCR). |
||||
|
1 |
SS configures: GNSS simulator is configured for Scenario #1: Scenario #1: static in Geographical area #1, and starts step 1 to simulate a location in the centre of Geographical area #1 as defined in TS 36.508 [18] Table 4.11.2-2. Geographical area #1 is also pre-configured in the UE/USIM. |
– |
– |
– |
– |
|
2 |
The SS transmits a Paging message including a systemInfoModification for cell1. |
<– |
Paging |
– |
– |
|
3 |
From the beginning of the next modification period the SS transmits SystemInformationBlockType21 according to Table 24.1.17.3.3-1. |
<– |
SystemInformationBlockType21 |
– |
– |
|
4 |
Wait for 1.1 modification periods for the UE to receive SystemInformationBlockType21 message. |
– |
– |
– |
– |
|
5 |
Steps 1 – 10a7 from the generic test procedure for Generic Radio Bearer Establishment (State 3) defined in TS 36.508 [18] clause 4.5.3 take place. |
||||
|
6 |
Close UE Test Loop with bit E0 in UE test loop mode E LB setup IE set to one (transmission mode). |
<– |
CLOSE UE TEST LOOP |
– |
– |
|
7 |
The UE responds with CLOSE UE TEST LOOP COMPLETE. |
–> |
CLOSE UE TEST LOOP COMPLETE |
– |
– |
|
8 |
UE transmit a SidelinkUEInformation message requesting resources for transmission of V2X sidelink communication in RRC_CONNECTED |
–> |
SidelinkUEInformation |
– |
– |
|
9 |
SS-NW releases the connection. |
<– |
RRCConnectionRelease |
– |
– |
|
10 |
Check: Does the UE transmit STCH PDCP SDU packets of V2X sidelink communication data over the PC5 interface in accordance with the resources indicated in resource pool 1 which is allowed to be used by the UE synchronised to eNB? NOTE:1 The UE may send multiple packets. The reception of one of them is sufficient for achieving the Pass verdict. NOTE 2: The structure of the data is not checked and it is just considered as octetstrings by the SS. |
–> |
STCH PDCP SDU packet |
1 |
P |
|
11 |
SS-NW changes SystemInformationBlockType21 according to Table 24.1.17.3.3-2. |
– |
– |
– |
– |
|
12 |
The SS transmits a Paging message in a paging occasion including a systemInfoModification. |
<– |
Paging |
– |
– |
|
13 |
Wait for 1.1 modification periods to allow for the UE to obtain the new version of the SystemInformationType21. |
– |
– |
– |
– |
|
14 |
Check: Does the UE transmit STCH PDCP SDU packets of V2X sidelink communication data over the PC5 interface accordance with the resources indicated in resource pool 2 which is allowed to be used by the UE synchronised to GNSS? NOTE 1: The UE may send multiple packets. The reception of one of them is sufficient for achieving the Pass verdict. NOTE 2: The structure of the data is not checked and it is just considered as octetstrings by the SS. |
–> |
STCH PDCP SDU packet |
1 |
P |
|
15 |
Steps 1 – 10a7 from the generic test procedure for Generic Radio Bearer Establishment (State 3) defined in TS 36.508 [18] clause 4.5.3 take place. |
– |
– |
– |
– |
|
16 |
The SS transmits an OPEN UE TEST LOOP message to exit the UE test loop mode. |
<– |
OPEN UE TEST LOOP |
– |
– |
|
17 |
The UE transmits an OPEN UE TEST LOOP COMPLETE message. |
–> |
OPEN UE TEST LOOP COMPLETE |
– |
– |
|
18 |
The SS transmits a DEACTIVATE TEST MODE message to de-activate UE radio bearer test mode procedure. |
<– |
DEACTIVATE TEST MODE |
– |
– |
|
19 |
The UE transmits a DEACTIVATE TEST MODE COMPLETE message. |
–> |
DEACTIVATE TEST MODE COMPLETE |
– |
– |
24.1.17.3.3 Specific message contents
Table 24.1.17.3.3-1: SystemInformationBlockType21 for Cell 1 (step 3, Table 24.1.17.3.2-1)
|
Derivation Path: 36.508 [18], table 4.4.3.3-19 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
SystemInformationBlockType21-r14 ::= SEQUENCE { |
|||
|
sl-V2X-ConfigCommon-r14 SEQUENCE { |
|||
|
v2x-InterFreqInfoList-r14 SEQUENCE { |
|||
|
SL-InterFreqInfoV2X-r14[1] SEQUENCE { |
|||
|
v2x-CommCarrierFreq-r14 |
f5 in TS 36.508 [18] clause 6.2.3.5 |
||
|
v2x-UE-ConfigList-r14 SEQUENCE { |
|||
|
v2x-CommTxPoolNormal-r14[1] SEQUENCE { |
|||
|
SL-CommResourcePoolV2X-r14[1] SEQUENCE { |
|||
|
sl-OffsetIndicator-r14 |
Not present |
||
|
sl-Subframe-r14 CHOICE { |
|||
|
bs20-r14 |
11110000000000000000 |
||
|
} |
|||
|
adjacencyPSCCH-PSSCH-r14 |
true |
BOOLEAN |
|
|
sizeSubchannel-r14 |
n5 |
BW10 |
|
|
n10 |
BW20 |
||
|
numSubchannel-r14 |
n10 |
||
|
startRB-Subchannel-r14 |
0 |
||
|
startRB-PSCCH-Pool-r14 |
Not present |
||
|
rxParametersNCell-r14 |
Not present |
||
|
dataTxParameters-r14 {} |
Not present |
||
|
dataTxParameters-r14 SEQUENCE { |
COND_TX |
||
|
alpha-r12 |
al0 |
||
|
p0-r12 |
31 |
||
|
} |
|||
|
zoneID-r14 |
Not present |
INTEGER (0..7) |
|
|
threshS-RSSI-CBR-r14 |
Not present |
INTEGER (0..45) |
|
|
poolReportId-r14 |
Not present |
||
|
cbr-pssch-TxConfigList-r14 |
Not present |
||
|
resourceSelectionConfigP2X-r14 |
Not present |
||
|
syncAllowed-r14 SEQUENCE { |
|||
|
gnss-Sync-r14 |
Not present |
||
|
enb-Sync-r14 |
true |
||
|
ue-Sync-r14 |
Not present |
||
|
} |
|||
|
restrictResourceReservationPeriod-r14 |
Not present |
||
|
} |
|||
|
SL-CommResourcePoolV2X-r14[2] SEQUENCE { |
|||
|
sl-OffsetIndicator-r14 |
Not present |
||
|
sl-Subframe-r14 CHOICE { |
|||
|
bs20-r14 |
00001111000000000000 |
||
|
} |
|||
|
adjacencyPSCCH-PSSCH-r14 |
true |
BOOLEAN |
|
|
sizeSubchannel-r14 |
n5 |
BW10 |
|
|
n10 |
BW20 |
||
|
numSubchannel-r14 |
n10 |
||
|
startRB-Subchannel-r14 |
0 |
||
|
startRB-PSCCH-Pool-r14 |
Not present |
||
|
rxParametersNCell-r14 |
Not present |
||
|
dataTxParameters-r14 {} |
Not present |
||
|
dataTxParameters-r14 SEQUENCE { |
COND_TX |
||
|
alpha-r12 |
al0 |
||
|
p0-r12 |
31 |
||
|
} |
|||
|
zoneID-r14 |
Not present |
INTEGER (0..7) |
|
|
threshS-RSSI-CBR-r14 |
Not present |
INTEGER (0..45) |
|
|
poolReportId-r14 |
Not present |
||
|
cbr-pssch-TxConfigList-r14 |
Not present |
||
|
resourceSelectionConfigP2X-r14 |
Not present |
||
|
syncAllowed-r14 SEQUENCE { |
|||
|
gnss-Sync-r14 |
true |
||
|
enb-Sync-r14 |
Not present |
||
|
ue-Sync-r14 |
Not present |
||
|
} |
|||
|
restrictResourceReservationPeriod-r14 |
Not present |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
Table 24.1.17.3.3-2: SystemInformationBlockType21 for Cell 1 (step 11, Table 24.1.17.3.2-1)
|
Derivation Path: 36.508 [18], table 4.4.3.3-19 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
SystemInformationBlockType21-r14 ::= SEQUENCE { |
|||
|
sl-V2X-ConfigCommon-r14 SEQUENCE { |
|||
|
v2x-InterFreqInfoList-r14 SEQUENCE { |
|||
|
SL-InterFreqInfoV2X-r14[1] SEQUENCE { |
|||
|
v2x-CommCarrierFreq-r14 |
f5 in TS 36.508 [18] clause 6.2.3.5 |
||
|
v2x-UE-ConfigList-r14 SEQUENCE { |
|||
|
v2x-CommTxPoolNormal-r14[1] SEQUENCE { |
|||
|
SL-CommResourcePoolV2X-r14[1] SEQUENCE { |
|||
|
sl-OffsetIndicator-r14 |
Not present |
||
|
sl-Subframe-r14 CHOICE { |
|||
|
bs20-r14 |
11110000000000000000 |
||
|
} |
|||
|
adjacencyPSCCH-PSSCH-r14 |
true |
BOOLEAN |
|
|
sizeSubchannel-r14 |
n5 |
BW10 |
|
|
n10 |
BW20 |
||
|
numSubchannel-r14 |
n10 |
||
|
startRB-Subchannel-r14 |
0 |
||
|
startRB-PSCCH-Pool-r14 |
Not present |
||
|
rxParametersNCell-r14 |
Not present |
||
|
dataTxParameters-r14 {} |
Not present |
||
|
dataTxParameters-r14 SEQUENCE { |
COND_TX |
||
|
alpha-r12 |
al0 |
||
|
p0-r12 |
31 |
||
|
} |
|||
|
zoneID-r14 |
Not present |
INTEGER (0..7) |
|
|
threshS-RSSI-CBR-r14 |
Not present |
INTEGER (0..45) |
|
|
poolReportId-r14 |
Not present |
||
|
cbr-pssch-TxConfigList-r14 |
Not present |
||
|
resourceSelectionConfigP2X-r14 |
Not present |
||
|
syncAllowed-r14 SEQUENCE { |
|||
|
gnss-Sync-r14 |
Not present |
||
|
enb-Sync-r14 |
true |
||
|
ue-Sync-r14 |
Not present |
||
|
} |
|||
|
restrictResourceReservationPeriod-r14 |
Not present |
||
|
} |
|||
|
SL-CommResourcePoolV2X-r14[2] SEQUENCE { |
|||
|
sl-OffsetIndicator-r14 |
Not present |
||
|
sl-Subframe-r14 CHOICE { |
|||
|
bs20-r14 |
00001111000000000000 |
||
|
} |
|||
|
adjacencyPSCCH-PSSCH-r14 |
true |
BOOLEAN |
|
|
sizeSubchannel-r14 |
n5 |
BW10 |
|
|
n10 |
BW20 |
||
|
numSubchannel-r14 |
n10 |
||
|
startRB-Subchannel-r14 |
0 |
||
|
startRB-PSCCH-Pool-r14 |
Not present |
||
|
rxParametersNCell-r14 |
Not present |
||
|
dataTxParameters-r14 {} |
Not present |
||
|
dataTxParameters-r14 SEQUENCE { |
COND_TX |
||
|
alpha-r12 |
al0 |
||
|
p0-r12 |
31 |
||
|
} |
|||
|
zoneID-r14 |
Not present |
INTEGER (0..7) |
|
|
threshS-RSSI-CBR-r14 |
Not present |
INTEGER (0..45) |
|
|
poolReportId-r14 |
Not present |
||
|
cbr-pssch-TxConfigList-r14 |
Not present |
||
|
resourceSelectionConfigP2X-r14 |
Not present |
||
|
syncAllowed-r14 SEQUENCE { |
|||
|
gnss-Sync-r14 |
true |
||
|
enb-Sync-r14 |
Not present |
||
|
ue-Sync-r14 |
Not present |
||
|
} |
|||
|
restrictResourceReservationPeriod-r14 |
Not present |
||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
} |
|||
|
typeTxSync-r14 |
gnss |
||
|
} |
|||
|
} |
|||
Table 24.1.17.3.3-3: SL-V2X-Preconfiguration
|
Derivation Path: 36.508 [18], table 6.8.2.1-1 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
SL-V2X-Preconfiguration-r14 ::= SEQUENCE { |
|||
|
anchorCarrierFreqList-r14 SEQUENCE (SIZE (1..maxFreq)) OF SEQUENCE { |
1 entries |
||
|
ARFCN-ValueEUTRA-r9[1] |
f1 in TS 36.508 [18] clause 6.2.3.1 |
||
|
} |
|||
|
} |
|||