B.3 UL power control when losing UL synchronization
25.2143GPPPhysical layer procedures (FDD)Release 17TS
Each Node B operates the uplink power control independently of the other Node Bs that may be providing RLS to the same UE. In case of multiple RLS the UE derives the decision on power adjustment based on all the commands received according the rules specified in subclause 5.1.2. In this scenario, transmission of a down command by one or more of the involved Node Bs will likely result in the UE decreasing its transmit power.
Consequently, if and when, after successful initial RL synchronization, the Node B loses UL synchronization for a UE and if the current number of RLS configured for that UE is greater than one and if the Node B reverts to a TPC pattern in such situation (i.e. generates DL TPC commands independently of actual RL measurements), the Node B should not use TPC commands “0” in the TPC pattern.
Annex C (Informative):
Cell search procedure
During the cell search, the UE searches for a cell and determines the downlink scrambling code and frame synchronization of that cell. The cell search is typically carried out in three steps:
Step 1: Slot synchronization
During the first step of the cell search procedure the UE uses the SCH’s primary synchronization code to acquire slot synchronization to a cell. This is typically done with a single matched filter (or any similar device) matched to the primary synchronization code which is common to all cells. The slot timing of the cell can be obtained by detecting peaks in the matched filter output.
Step 2: Frame synchronization and code-group identification
During the second step of the cell search procedure, the UE uses the SCH’s secondary synchronization code to find frame synchronization and identify the code group of the cell found in the first step. This is done by correlating the received signal with all possible secondary synchronization code sequences, and identifying the maximum correlation value. Since the cyclic shifts of the sequences are unique the code group as well as the frame synchronization is determined.
Step 3: Scrambling-code identification
During the third and last step of the cell search procedure, the UE determines the exact primary scrambling code used by the found cell. The primary scrambling code is typically identified through symbol-by-symbol correlation over the CPICH with all codes within the code group identified in the second step. After the primary scrambling code has been identified, the Primary CCPCH can be detected. And the system- and cell specific BCH information can be read.
If the UE has received information about which scrambling codes to search for, steps 2 and 3 above can be simplified.
Annex D (Informative):
F-TPICH Transmission
The F-TPICH transmission timing described in this annex should be seen as an example on how the TPI bits have to be placed in order to ensure a short TPI delay.
In response to the reception of the TPI bits on the F-TPICH channel, the UE shall apply the precoding weights indicated by the TPI bits at the first UL DPCCH slot that is transmitted at least 512 bits after the reception of the last of the two TPI symbols. The reliability of the received TPI bit is determined by the UE based on the downlink SIR measurement on the F-TPICH channel.
Figure D.1 illustrates an example of F-TPICH timing for UL CLTD operation when the F-TPICH frame starts 512 chips after the start of the DPCH/F-DPCH frame.
Figure D.1: F-TPICH Transmission timing for UL CLTD when F-TPICH frame starts 512 chips after the start of DPCH/F-DPCH frame
Annex E (informative):
Change history
Change history |
|||||||
---|---|---|---|---|---|---|---|
Date |
TSG # |
TSG Doc. |
CR |
Rev |
Subject/Comment |
Old |
New |
RP_05 |
RP-99531 |
– |
Approved at TSG RAN #5 and placed under Change Control |
– |
3.0.0 |
||
14/01/00 |
RP_06 |
RP-99686 |
003 |
2 |
Flexible timing of UTRAN response to uplink closed loop Tx diversity feedback commands |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99686 |
006 |
2 |
CPCH power control preamble length |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99686 |
007 |
– |
Removal of open loop power control |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99687 |
008 |
– |
Power offset of AICH and PICH |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99686 |
009 |
1 |
Update of Random Access Procedure |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99686 |
010 |
1 |
oft symbol combining for uplink power control |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99685 |
011 |
– |
Clarification of closed loop transmit diversity figure in clause 8 and closed loop operation in compressed mode for mode 2 in subclause 8.3 of TS 25.214 |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99686 |
012 |
– |
Uplink power control maximum TX power |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99686 |
013 |
1 |
Setting of beta values for multi-code |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99686 |
014 |
– |
Consolidation of CPCH Power Control Preamble Information |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99686 |
015 |
1 |
Consolidation of Power Control Information for DCH Initialisation |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99686 |
016 |
– |
Uplink power control in compressed mode |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99686 |
018 |
1 |
Timing for initialisation procedures |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99687 |
021 |
– |
20 ms RACH message length |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99684 |
023 |
1 |
Maximum Tx Power at uplink compressed Mode |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99687 |
024 |
2 |
Setting of power in uplink compressed mode |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99687 |
025 |
– |
Cleanup of synchronization procedures |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99686 |
026 |
2 |
Downlink power control |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99687 |
029 |
– |
Out-of-synch handling |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99687 |
030 |
2 |
State update rule addition to SSDT specification |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99687 |
033 |
– |
Uplink TX timing adjustment |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99687 |
036 |
– |
Inclusion of idle periods for the IPDL LCS |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99686 |
041 |
– |
Revision of power control timing text |
3.0.0 |
3.1.0 |
14/01/00 |
RP_06 |
RP-99687 |
042 |
1 |
Inclusion of adjustment loop in downlink power control |
3.0.0 |
3.1.0 |
14/01/00 |
– |
– |
– |
Change history was added by the editor |
3.1.0 |
3.1.1 |
|
31/03/00 |
RP_07 |
RP-000064 |
043 |
1 |
Optimum ID Codes for SSDT Power Control |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
044 |
– |
Editorial clarification to subclause 5.1.2.2.2 |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
047 |
1 |
Additional description of TX diversity for PDSCH |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
048 |
– |
Power offset on S-CCPCH |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
050 |
2 |
Corrections to uplink power control |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
055 |
– |
Correction of Adjustment loop description |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
056 |
1 |
Clarification of TPC command combining for Algorithm 1 |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
057 |
– |
Clarification of TPC command combining for Algorithm 2 |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
059 |
2 |
CPCH:CD subslot-related additions to 6.2 |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
061 |
1 |
CPCH: editorial changes and clarifications of 6.2 |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
062 |
– |
Editorial corrections |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
064 |
1 |
Editorial improvement of the IPDL section |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
065 |
1 |
PRACH power offset definition |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
066 |
1 |
Radio link synchronization in UTRA/FDD |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
068 |
– |
Definition for maximum and minimum DL power |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
069 |
4 |
Channel assignment and UE channel selection methods of CPCH |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
071 |
– |
Channelization code allocation method for PCPCH message part |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
072 |
1 |
Limited power raise used -parameter in DL PC |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
080 |
– |
Downlink power control |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000064 |
081 |
– |
Editorial improvement on SSDT power control section |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000065 |
082 |
2 |
Emergency Stop of CPCH transmission and Start of Message Indicator |
3.1.1 |
3.2.0 |
31/03/00 |
RP_07 |
RP-000065 |
083 |
– |
Clean up of USTS related specifications |
3.1.1 |
3.2.0 |
26/06/00 |
RP_08 |
RP-000268 |
084 |
– |
Addition of CSICH power parameter |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
085 |
– |
Correction to power control in compressed mode recovery period |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
086 |
1 |
Revisions to power control for CPCH |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
087 |
– |
Corrections to uplink DCH power control sections |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
090 |
3 |
Level of specification of downlink power control |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
091 |
1 |
Clarification of TX diversity power setting |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
092 |
– |
PICH undefined bits |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
095 |
1 |
DPDCH/DPCCH gain factors |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
096 |
3 |
Correction to RACH subchannel definition |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
097 |
1 |
The power setting of the CCC field of DL DPCCH for CPCH |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
098 |
4 |
Procedure for end of transmission indicator in CPCH |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
099 |
– |
Downlink inner-loop power control in compressed mode |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
100 |
– |
Definition of vector transmission weight entity |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
101 |
1 |
Number of slots for DPCCH power control preamble |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
102 |
– |
Clarification of UTRAN Tx diversity response timing description in 25.214 |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
103 |
2 |
Corrections to transmit diversity section |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
104 |
1 |
Corrections to uplink power control in compressed mode |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
105 |
– |
Clarification of downlink power control mode |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
106 |
– |
Clarification of radio link set |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000268 |
107 |
1 |
Clarification of radio link synchronization procedure |
3.2.0 |
3.3.0 |
26/06/00 |
RP_08 |
RP-000269 |
108 |
– |
Correctly quantized gain factors for uplink compressed mode |
3.2.0 |
3.3.0 |
23/09/00 |
RP_09 |
RP-000342 |
110 |
4 |
Downlink inner-loop power control in compressed mode |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000342 |
112 |
– |
Adding reference for power offset variation text in TS 25.214 |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000342 |
113 |
– |
Combining TPC commands in soft handover |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000342 |
115 |
1 |
Corrections to power control |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000342 |
116 |
– |
Corrections to 25.214 |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000342 |
117 |
– |
Clarification to downlink power control |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000342 |
118 |
3 |
Clarification of power control at maximum and minimum power |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000342 |
119 |
– |
Clarification of SSDT text |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000342 |
120 |
– |
Corrections to CL transmit diversity mode 1 |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000342 |
121 |
1 |
Clarification of SSDT ID code bit transmission order |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000342 |
122 |
1 |
Clarification on RACH and CPCH subchannel definition |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000342 |
123 |
1 |
DPCH initialisation procedure |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000342 |
124 |
– |
Clarification of closed loop mode TX diversity initialisation |
3.3.0 |
3.4.0 |
23/09/00 |
RP_09 |
RP-000342 |
127 |
2 |
Uplink power control in compressed mode |
3.3.0 |
3.4.0 |
15/12/00 |
RP_10 |
RP-000540 |
128 |
1 |
Clarification of downlink quality measurement in SSDT |
3.4.0 |
3.5.0 |
15/12/00 |
RP_10 |
RP-000540 |
129 |
– |
Formula typography and reference corrections |
3.4.0 |
3.5.0 |
15/12/00 |
RP_10 |
RP-000540 |
130 |
1 |
Radio link establishment and sync status reporting |
3.4.0 |
3.5.0 |
15/12/00 |
RP_10 |
RP-000540 |
133 |
– |
Correction of RACH/CPCH physical random access procedure |
3.4.0 |
3.5.0 |
15/12/00 |
RP_10 |
RP-000540 |
134 |
– |
Correction of uplink power control algorithm 2 |
3.4.0 |
3.5.0 |
15/12/00 |
RP_10 |
RP-000540 |
135 |
1 |
TPC command generation on downlink during RLS initialization |
3.4.0 |
3.5.0 |
15/12/00 |
RP_10 |
RP-000540 |
136 |
1 |
Clarification of RACH behavior at maximum and minimum power |
3.4.0 |
3.5.0 |
15/12/00 |
RP_10 |
RP-000540 |
137 |
– |
Clarifications on the description of the radio link establishment procedure (when no radio link exists) |
3.4.0 |
3.5.0 |
15/12/00 |
RP_10 |
RP-000540 |
138 |
1 |
Corrections on power control preambles |
3.4.0 |
3.5.0 |
15/12/00 |
RP_10 |
RP-000540 |
139 |
1 |
Clarification of RACH procedure |
3.4.0 |
3.5.0 |
15/12/00 |
RP_10 |
RP-000540 |
140 |
– |
Uplink power control in compressed mode |
3.4.0 |
3.5.0 |
15/12/00 |
RP_10 |
RP-000540 |
141 |
1 |
Revision of the abbreviation list |
3.4.0 |
3.5.0 |
16/03/01 |
RP_11 |
– |
– |
– |
Approved as Release 4 specification (v4.0.0) at TSG RAN #11 |
3.5.0 |
4.0.0 |
16/03/01 |
RP_11 |
RP-010060 |
142 |
1 |
Uplink power control in compressed mode |
3.5.0 |
4.0.0 |
16/03/01 |
RP_11 |
RP-010060 |
144 |
– |
Removal of the power balancing algorithm from TS 25.214 |
3.5.0 |
4.0.0 |
16/03/01 |
RP_11 |
RP-010254 |
145 |
2 |
Clarification of Nid parameter – when SSDT and uplink compressed mode are in operation |
3.5.0 |
4.0.0 |
16/03/01 |
RP_11 |
RP-010060 |
146 |
– |
Clarification of closed loop transmit diversity mode 1 and mode 2 operation during compressed mode |
3.5.0 |
4.0.0 |
16/03/01 |
RP_11 |
RP-010060 |
148 |
1 |
Clarification of UE SIR estimation |
3.5.0 |
4.0.0 |
16/03/01 |
RP_11 |
RP-010060 |
150 |
1 |
Clarification of the order of SSDT signalling in 2 bit FBI |
3.5.0 |
4.0.0 |
16/03/01 |
RP_11 |
RP-010244 |
154 |
2 |
Uplink power control preamble |
3.5.0 |
4.0.0 |
16/03/01 |
RP_11 |
RP-010060 |
155 |
– |
Correction of limited power raise |
3.5.0 |
4.0.0 |
16/03/01 |
RP_11 |
RP-010060 |
156 |
– |
Clarification of initialization procedure |
3.5.0 |
4.0.0 |
16/03/01 |
RP_11 |
RP-010060 |
158 |
– |
Definition of power control step size for algorithm 2 |
3.5.0 |
4.0.0 |
16/03/01 |
RP_11 |
RP-010060 |
161 |
1 |
Correction of the UE behavior in SSDT mode |
3.5.0 |
4.0.0 |
16/03/01 |
RP_11 |
RP-010060 |
163 |
– |
Correction on downlink synchronization primitives |
3.5.0 |
4.0.0 |
16/03/01 |
RP_11 |
RP-010074 |
149 |
1 |
DSCH Power Control Improvement in soft handover |
3.5.0 |
4.0.0 |
15/06/01 |
RP_12 |
RP-010334 |
166 |
1 |
Limited power raise: aligning of terminology with TS25.433 |
4.0.0 |
4.1.0 |
15/06/01 |
RP_12 |
RP-010334 |
167 |
1 |
Correction of IPDL burst parameters |
4.0.0 |
4.1.0 |
15/06/01 |
RP_12 |
RP-010334 |
169 |
1 |
Correction of synchronization primitives |
4.0.0 |
4.1.0 |
15/06/01 |
RP_12 |
RP-010334 |
177 |
1 |
Clarification on TPC command generation on downlink during RL initialisation |
4.0.0 |
4.1.0 |
15/06/01 |
RP_12 |
RP-010482 |
181 |
4 |
Clarification of synchronization procedures |
4.0.0 |
4.1.0 |
15/06/01 |
RP_12 |
RP-010334 |
183 |
– |
Clarification of initialisation of closed loop mode 1 and 2 during compressed mode |
4.0.0 |
4.1.0 |
15/06/01 |
RP_12 |
RP-010334 |
186 |
– |
DL maximum power level in compressed mode |
4.0.0 |
4.1.0 |
15/06/01 |
RP_12 |
RP-010341 |
164 |
1 |
Clarification on the usage of SSDT signaling in uplink |
4.0.0 |
4.1.0 |
21/09/01 |
RP_13 |
RP-010520 |
192 |
– |
Corrections and Clarifications for calculation of idle period position in subclause 8.3 in 25.214 |
4.1.0 |
4.2.0 |
21/09/01 |
RP_13 |
RP-010520 |
194 |
1 |
Minor modifications to the CPCH access procedure |
4.1.0 |
4.2.0 |
21/09/01 |
RP_13 |
RP-010520 |
197 |
– |
Downlink power control in compressed mode |
4.1.0 |
4.2.0 |
21/09/01 |
RP_13 |
RP-010520 |
199 |
1 |
Improvements of closed loop TX diversity description |
4.1.0 |
4.2.0 |
21/09/01 |
RP_13 |
RP-010520 |
201 |
1 |
Correction to Random access procedure (Primitive from MAC) |
4.1.0 |
4.2.0 |
21/09/01 |
RP_13 |
RP-010677 |
205 |
1 |
Proposed CR to TS25.214: Clarification of the SSDT behaviour with beam forming |
4.1.0 |
4.2.0 |
21/09/01 |
RP_13 |
RP-010527 |
195 |
1 |
Enhanced PDSCH power control clarification |
4.1.0 |
4.2.0 |
14/12/01 |
RP_14 |
RP-010739 |
207 |
1 |
Power control in compressed mode when DPC_MODE=1 |
4.2.0 |
4.3.0 |
14/12/01 |
RP_14 |
RP-010739 |
209 |
– |
Clarification of closed loop mode 1 and 2 Tx diversity operation during compressed mode |
4.2.0 |
4.3.0 |
14/12/01 |
RP_14 |
RP-010739 |
211 |
– |
Downlink phase reference reconfiguration |
4.2.0 |
4.3.0 |
14/12/01 |
RP_14 |
RP-010739 |
219 |
1 |
Downlink power control for channels supporting CPCH |
4.2.0 |
4.3.0 |
14/12/01 |
RP_14 |
RP-010739 |
223 |
– |
Removal of slow power control from TS 25.214 |
4.2.0 |
4.3.0 |
14/12/01 |
RP_14 |
RP-010775 |
216 |
– |
Uplink TPC command processing in SHO with SSDT |
4.2.0 |
4.3.0 |
14/12/01 |
RP_14 |
RP-010744 |
217 |
2 |
DSCH power control clarification |
4.2.0 |
4.3.0 |
14/12/01 |
RP_14 |
RP-010933 |
229 |
– |
Restriction to SSDT and closed loop mode transmit diversity combination |
4.2.0 |
4.3.0 |
08/03/02 |
RP_15 |
RP-020047 |
227 |
– |
Clarification on DPCCH dedicated pilot bits with closed loop mode1 |
4.3.0 |
4.4.0 |
08/03/02 |
RP_15 |
RP-020261 |
231 |
3 |
Qth threshold parameter in SSDT |
4.3.0 |
4.4.0 |
08/03/02 |
RP_15 |
RP-020047 |
240 |
1 |
TPC procedure in UE when SSDT is activated |
4.3.0 |
4.4.0 |
08/03/02 |
RP_15 |
RP-020053 |
236 |
1 |
Clarification of closed loop transmit diversity during soft handover |
4.3.0 |
4.4.0 |
08/03/02 |
RP_15 |
RP-020054 |
250 |
1 |
Description of SSDT operation for TFCI power control in hard split mode |
4.3.0 |
5.0.0 |
08/03/02 |
RP_15 |
RP-020058 |
237 |
2 |
Introduction of HSDPA feature to TS25.214 |
4.3.0 |
5.0.0 |
08/03/02 |
RP_15 |
RP-020058 |
251 |
– |
Introduction of power control aspects for HSDPA feature in TS25.214 |
4.3.0 |
5.0.0 |
07/06/02 |
RP_16 |
RP-020316 |
255 |
2 |
Correction on the operation of HSDPA during compressed mode |
5.0.0 |
5.1.0 |
07/06/02 |
RP_16 |
RP-020316 |
259 |
1 |
Clarification of UE transmission timing adjustment with HS-DPCCH |
5.0.0 |
5.1.0 |
07/06/02 |
RP_16 |
RP-020316 |
260 |
4 |
Definition of CQI reporting |
5.0.0 |
5.1.0 |
07/06/02 |
RP_16 |
RP-020316 |
266 |
– |
Correction to the setting of DPCCH/HS-DPCCH power difference |
5.0.0 |
5.1.0 |
07/06/02 |
RP_16 |
RP-020316 |
267 |
– |
Inclusion of CQI table |
5.0.0 |
5.1.0 |
07/06/02 |
RP_16 |
RP-020318 |
265 |
1 |
Definition of Qth threshold parameter in SSDT |
5.0.0 |
5.1.0 |
17/09/02 |
RP_17 |
RP-020584 |
263 |
– |
Clarification of total HS-SCCH/HS-PDSCH power |
5.1.0 |
5.2.0 |
17/09/02 |
RP_17 |
RP-020571 |
272 |
– |
Reversal of unwanted corrections resulting from CR 25.211-122 & CR 25.214-226 |
5.1.0 |
5.2.0 |
17/09/02 |
RP_17 |
RP-020584 |
273 |
2 |
Clarification of total HS-PDSCH power in CQI reporting procedure |
5.1.0 |
5.2.0 |
17/09/02 |
RP_17 |
RP-020584 |
274 |
1 |
Closed loop transmit diversity mode 2 with antenna verification |
5.1.0 |
5.2.0 |
17/09/02 |
RP_17 |
RP-020589 |
279 |
– |
Correction of maximum power adjustment in case of compressed mode |
5.1.0 |
5.2.0 |
17/09/02 |
RP_17 |
RP-020574 |
282 |
1 |
Enhanced DSCH power control parameter name change |
5.1.0 |
5.2.0 |
17/09/02 |
RP_17 |
RP-020584 |
287 |
2 |
Correction of CQI definition |
5.1.0 |
5.2.0 |
17/09/02 |
RP_17 |
RP-020587 |
288 |
– |
Inclusion of closed loop transmit diversity for HSDPA |
5.1.0 |
5.2.0 |
17/09/02 |
RP_17 |
RP-020588 |
289 |
– |
Correction of timing of CQI reporting |
5.1.0 |
5.2.0 |
17/09/02 |
RP_17 |
RP-020529 |
294 |
– |
Correction of reference linked to approval of CR 25.133-471 |
5.1.0 |
5.2.0 |
17/09/02 |
RP_17 |
RP-020584 |
296 |
– |
The clarification of CQI feedback parameter k value |
5.1.0 |
5.2.0 |
17/09/02 |
RP_17 |
RP-020584 |
298 |
– |
Clarification of CQI definition and reference period |
5.1.0 |
5.2.0 |
17/09/02 |
RP_17 |
RP-020584 |
286 |
1 |
Numbering corrections |
5.1.0 |
5.2.0 |
20/12/02 |
RP_18 |
RP-020847 |
300 |
1 |
Corrections and clarifications to FDD CQI description |
5.2.0 |
5.3.0 |
20/12/02 |
RP_18 |
RP-020847 |
301 |
1 |
Criterion to determine primary cell for DSCH power control improvement |
5.2.0 |
5.3.0 |
20/12/02 |
RP_18 |
RP-020851 |
304 |
2 |
Introduction of Transport Block Size signaling procedure reference. |
5.2.0 |
5.3.0 |
20/12/02 |
RP_18 |
RP-020841 |
307 |
– |
Clarification of closed loop timing adjustment mode |
5.2.0 |
5.3.0 |
26/03/03 |
RP_19 |
RP-030136 |
299 |
5 |
CQI reporting with TxD |
5.3.0 |
5.4.0 |
26/03/03 |
RP_19 |
RP-030136 |
313 |
1 |
On closed loop transmit diversity mode 1 verification algorithm |
5.3.0 |
5.4.0 |
26/03/03 |
RP_19 |
RP-030136 |
315 |
2 |
Clarification of SSDT and HSDPA |
5.3.0 |
5.4.0 |
26/03/03 |
RP_19 |
RP-030132 |
318 |
– |
Correction on verification algorithm in Annex 1 |
5.3.0 |
5.4.0 |
23’06/03 |
RP_20 |
RP-030273 |
314 |
1 |
Correction of TPC command combining in SHO |
5.4.0 |
5.5.0 |
23’06/03 |
RP_20 |
RP-030273 |
319 |
– |
Correction for HS-DPCCH gain factor in compressed frame |
5.4.0 |
5.5.0 |
23’06/03 |
RP_20 |
RP-030273 |
320 |
1 |
Clarification of HS-SCCH reception in case of minimum interTTI interval is not 1 |
5.4.0 |
5.5.0 |
23’06/03 |
RP_20 |
RP-030273 |
321 |
– |
Correction of description of CQI transmission timing calculation |
5.4.0 |
5.5.0 |
23’06/03 |
RP_20 |
RP-030273 |
322 |
1 |
Clarification of the reference power for HS-DPCCH |
5.4.0 |
5.5.0 |
21/09/03 |
RP_21 |
RP-030458 |
325 |
– |
Correction of CQI definition table |
5.5.0 |
5.6.0 |
21/09/03 |
RP_21 |
RP-030462 |
326 |
– |
Removal of the combination of TxAA Mode 1 with HS-SCCH |
5.5.0 |
5.6.0 |
21/09/03 |
RP_21 |
RP-030458 |
328 |
2 |
Clarification of power scaling with HS-DPCCH |
5.5.0 |
5.6.0 |
21/09/03 |
RP_21 |
RP-030458 |
329 |
3 |
Correction of CQI reporting in DL compressed mode |
5.5.0 |
5.6.0 |
21/09/03 |
RP_21 |
RP-030458 |
330 |
1 |
Clarification of HS-SCCH reception |
5.5.0 |
5.6.0 |
21/09/03 |
RP_21 |
RP-030458 |
333 |
1 |
Clarification on CQI repetition behaviour |
5.5.0 |
5.6.0 |
21/09/03 |
RP_21 |
RP-030547 |
335 |
3 |
TPC pattern during loss of RL synchronization |
5.5.0 |
5.6.0 |
06/01/04 |
RP_22 |
RP-030649 |
335 |
1 |
Clarification of HS-SCCH reception |
5.6.0 |
5.7.0 |
06/01/04 |
RP_22 |
RP-030649 |
336 |
1 |
Clarification of CQI definition |
5.6.0 |
5.7.0 |
06/01/04 |
RP_22 |
RP-030649 |
337 |
1 |
Clarification of the HS-SCCH detection |
5.6.0 |
5.7.0 |
06/01/04 |
RP_22 |
RP-030661 |
338 |
– |
Remove inconsistency among specifications on signalling support for power control during loss of RL synchronization |
5.6.0 |
5.7.0 |
06/01/04 |
RP_22 |
RP-030712 |
339 |
– |
Alignment of "Soft channel bits" terminology with 25.306 |
5.6.0 |
5.7.0 |
13/01/04 |
RP_22 |
– |
– |
– |
Created for M.1457 update |
5.7.0 |
6.0.0 |
23/03/04 |
RP_23 |
RP-040086 |
341 |
– |
Beta values for HS-DPCCH in compressed mode |
6.0.0 |
6.1.0 |
23/03/04 |
RP_23 |
RP-040086 |
346 |
1 |
ACK/NACK repetition factor |
6.0.0 |
6.1.0 |
09/06/04 |
RP_24 |
RP-040257 |
350 |
3 |
Clarification of UE procedure in case of HHO failure |
6.1.0 |
6.2.0 |
28/09/04 |
RP_25 |
RP-040318 |
352 |
1 |
Clarification of SSDT uplink only signalling |
6.2.0 |
6.3.0 |
13/12/04 |
RP_26 |
RP-040449 |
361 |
1 |
Introduction of E-DCH |
6.3.0 |
6.4.0 |
13/12/04 |
RP_26 |
RP-040450 |
351 |
– |
Introduction of MICH |
6.3.0 |
6.4.0 |
13/12/04 |
RP_26 |
RP-040448 |
356 |
1 |
Introduction of MBMS Soft Combining |
6.3.0 |
6.4.0 |
13/12/04 |
RP_26 |
RP-040447 |
360 |
– |
Correction of downlink transmit power control in compressed mode |
6.3.0 |
6.4.0 |
13/12/04 |
RP_26 |
RP-040527 |
358 |
1 |
Preamble and Postamble to reduce HS-DPCCH transmit power |
6.3.0 |
6.4.0 |
14/03/05 |
RP_27 |
RP-050048 |
362 |
2 |
Gain factor setting for E-DCH |
6.4.0 |
6.5.0 |
14/03/05 |
RP_27 |
RP-050049 |
364 |
1 |
Reliable E-RGCH/E-HICH Detection |
6.4.0 |
6.5.0 |
14/03/05 |
RP_27 |
RP-050088 |
368 |
1 |
Introduction of F-DPCH without pilot field |
6.4.0 |
6.5.0 |
14/03/05 |
RP_27 |
RP-050140 |
369 |
3 |
DL/UL timing association of E-DCH operation |
6.4.0 |
6.5.0 |
16/06/05 |
RP_28 |
RP-050254 |
354 |
4 |
Timing Maintained Hard Handover |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050253 |
355 |
4 |
Faster L1 DCH synchronization |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050252 |
363 |
4 |
Power control at the maximum power limit |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050252 |
372 |
4 |
Support of different HARQ profiles |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050252 |
373 |
– |
Lowest reference E-TFC for the gain factor setting for E-DCH |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050250 |
375 |
1 |
Feature Clean Up: Removal of “CPCH” |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050248 |
377 |
1 |
Feature Clean Up: Removal of DSCH (FDD mode) |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050333 |
378 |
1 |
F-DPCH Downlink Power Control Behaviour in SHO |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050256 |
379 |
– |
Correction to DL synchronization |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050252 |
380 |
3 |
Clarification on E-DCH timing |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050252 |
381 |
1 |
DPCCH gain factor with no DPDCH configured |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050252 |
382 |
2 |
Compressed mode operation for the Enhanced Uplink |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050244 |
384 |
– |
Feature Clean Up: Removal of “SSDT” |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050247 |
387 |
1 |
Feature clean up: Removal of the ‘TX diversity closed loop mode 2’ |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050249 |
389 |
1 |
Feature clean up: Removal of the ‘compressed mode by puncturing’ |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050246 |
391 |
1 |
Feature Clean Up: Removal of dedicated pilot as sole phase reference |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050251 |
392 |
1 |
Removal of MBMS Rake Combining |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050242 |
394 |
1 |
HS-DPCCH transmissions on discarding HS-SCCH |
6.5.0 |
6.6.0 |
16/06/05 |
RP_28 |
RP-050345 |
395 |
– |
Removal of E-RGCH non-serving radio link set |
6.5.0 |
6.6.0 |
26/09/05 |
RP_29 |
RP-050449 |
0398 |
– |
Power control annex for F-DPCH |
6.6.0 |
6.7.0 |
26/09/05 |
RP_29 |
RP-050447 |
0399 |
2 |
Faster L1 DCH Synchronization |
6.6.0 |
6.7.0 |
26/09/05 |
RP_29 |
RP-050449 |
0400 |
1 |
F-DPCH Quality Estimate |
6.6.0 |
6.7.0 |
26/09/05 |
RP_29 |
RP-050450 |
0401 |
2 |
Downlink compressed mode and E-HICH, E-RGCH and E-AGCH |
6.6.0 |
6.7.0 |
26/09/05 |
RP_29 |
RP-050440 |
0403 |
– |
Downlink HS total power limitation |
6.6.0 |
6.7.0 |
26/09/05 |
RP_29 |
RP-050450 |
0404 |
1 |
Clarification on power offset quantization |
6.6.0 |
6.7.0 |
26/09/05 |
RP_29 |
RP-050450 |
0405 |
– |
Clarification on computation of gain factors |
6.6.0 |
6.7.0 |
26/09/05 |
RP_29 |
RP-050450 |
0406 |
1 |
E-DPDCH power scaling at the maximum power limit |
6.6.0 |
6.7.0 |
26/09/05 |
RP_29 |
RP-050547 |
0407 |
2 |
Clarification on E-RGCH detection |
6.6.0 |
6.7.0 |
26/09/05 |
RP_29 |
RP-050645 |
0408 |
4 |
PRACH preamble power at minimum power transmission |
6.6.0 |
6.7.0 |
26/09/05 |
RP_29 |
RP-050450 |
0412 |
– |
Clarification on E-AGCH, EHICH, E-RGCH power control |
6.6.0 |
6.7.0 |
12/12/05 |
RP_30 |
– |
– |
– |
Editorial revision to the header format change of the chapter 6B.3 |
6.7.0 |
6.7.1 |
20/03/06 |
RP_31 |
RP-060076 |
0416 |
– |
Correction to number of configured DPDCHs in relation to E-DPDCH power scaling |
6.7.1 |
6.8.0 |
20/03/06 |
RP_31 |
– |
– |
– |
Creation of Release 7 specification (v7.0.0) at RAN#31 |
6.8.0 |
7.0.0 |
12/06/06 |
RP_32 |
RP-060293 |
0418 |
1 |
Correction of synchronization procedure |
7.0.0 |
7.1.0 |
12/06/06 |
RP_32 |
RP-060370 |
0420 |
– |
Clarification of E-TFCI terminology |
7.0.0 |
7.1.0 |
29/09/06 |
RP_33 |
RP-060490 |
0423 |
1 |
Clarification of E-DPDCH gain factor quantization |
7.1.0 |
7.2.0 |
11/12/06 |
RP_34 |
RP-060727 |
0432 |
3 |
Correction to E-DCH gain factor calculation in relation to compressed mode |
7.2.0 |
7.3.0 |
08/03/07 |
RP_35 |
RP-070114 |
0430 |
10 |
Definition of MIMO operation on HS-PDSCH, preferred precoding and CQI reporting procedures, modified CQI tables |
7.3.0 |
7.4.0 |
08/03/07 |
RP_35 |
RP-070115 |
0421 |
13 |
Support of CPC feature |
7.3.0 |
7.4.0 |
08/03/07 |
RP_35 |
RP-070116 |
0434 |
2 |
Introduction of 64QAM for HSDPA |
7.3.0 |
7.4.0 |
30/05/07 |
RP_36 |
RP-070388 |
0435 |
5 |
Introduction of 16-QAM for HSUPA |
7.4.0 |
7.5.0 |
30/05/07 |
RP_36 |
RP-070392 |
0437 |
2 |
Enhanced F-DPCH |
7.4.0 |
7.5.0 |
30/05/07 |
RP_36 |
RP-070389 |
0438 |
6 |
Clarification to the CPC feature |
7.4.0 |
7.5.0 |
30/05/07 |
RP_36 |
RP-070387 |
0440 |
– |
Setting of the uplink HS-DPCCH power relative to DPCCH power for MIMO |
7.4.0 |
7.5.0 |
30/05/07 |
RP_36 |
RP-070392 |
0446 |
1 |
Enhanced F-DPCH and CPC DL PC timing |
7.4.0 |
7.5.0 |
30/05/07 |
RP_36 |
RP-070384 |
0449 |
– |
Support for DL only SFN operation for MBMS FDD |
7.4.0 |
7.5.0 |
30/05/07 |
RP_36 |
RP-070392 |
0450 |
– |
Clarification on power control operation for F-DPCH enhancement |
7.4.0 |
7.5.0 |
30/05/07 |
RP_36 |
RP-070390 |
0451 |
1 |
Enhanced CELL_FACH Procedure |
7.4.0 |
7.5.0 |
11/09/07 |
RP_37 |
RP-070641 |
0452 |
2 |
CPC preamble and postamble clarification for CQI transmission |
7.5.0 |
7.6.0 |
11/09/07 |
RP_37 |
RP-070641 |
0453 |
– |
Removal of Inactivity_Threshold_for_UE_Grant_Monitoring definition |
7.5.0 |
7.6.0 |
11/09/07 |
RP_37 |
RP-070643 |
0454 |
2 |
Corrections to HS-DSCH procedures for CELL_FACH and MIMO |
7.5.0 |
7.6.0 |
11/09/07 |
RP_37 |
RP-070644 |
0456 |
3 |
Correction to Rel-7 E-DPDCH gain factor calculation |
7.5.0 |
7.6.0 |
11/09/07 |
RP_37 |
RP-070645 |
0458 |
1 |
Correction of 64QAM CQI tables |
7.5.0 |
7.6.0 |
11/09/07 |
RP_37 |
RP-070641 |
0459 |
– |
Clarification of CPC |
7.5.0 |
7.6.0 |
11/09/07 |
RP_37 |
RP-070644 |
0460 |
2 |
E-DPDCH scaling when UE is at max power |
7.5.0 |
7.6.0 |
11/09/07 |
RP_37 |
RP-070642 |
0462 |
1 |
Correction of MIMO CQI tables |
7.5.0 |
7.6.0 |
27/11/07 |
RP_38 |
RP-070945 |
0463 |
– |
Timing of CQI vs DTX priority change |
7.6.0 |
7.7.0 |
27/11/07 |
RP_38 |
RP-070945 |
0465 |
– |
Grant Monitoring clarification |
7.6.0 |
7.7.0 |
27/11/07 |
RP_38 |
RP-070947 |
0467 |
1 |
Clarification on CQI tables in Rel-7 |
7.6.0 |
7.7.0 |
27/11/07 |
RP_38 |
RP-070945 |
0469 |
2 |
Addition of TFRI to list of abbreviations |
7.6.0 |
7.7.0 |
27/11/07 |
RP_38 |
RP-070944 |
0470 |
– |
Correction to Rel-7 E-DPDCH gain factor calculation |
7.6.0 |
7.7.0 |
27/11/07 |
RP_38 |
RP-070941 |
0471 |
2 |
Clarification of CQI definition |
7.6.0 |
7.7.0 |
27/11/07 |
RP_38 |
RP-070947 |
0473 |
2 |
Clarification on HSDPA UE category in Rel-7 |
7.6.0 |
7.7.0 |
27/11/07 |
RP_38 |
RP-070911 |
0474 |
– |
Clarification on E-DPDCH power extrapolation/interpolation |
7.6.0 |
7.7.0 |
28/11/07 |
RP_38 |
RP-070948 |
0476 |
– |
Removing the constraint that the same HS-SCCH should be used in contiguous TTIs |
7.7.0 |
8.0.0 |
28/11/07 |
RP_38 |
RP-070950 |
0477 |
– |
Inclusion of CQI tables for the combination of 64QAM and MIMO |
7.7.0 |
8.0.0 |
04/03/08 |
RP_39 |
RP-080143 |
0480 |
1 |
Correction to UE grant monitoring |
8.0.0 |
8.1.0 |
28/05/08 |
RP_40 |
RP-080350 |
0482 |
2 |
CPC DTX cycle change clarification |
8.1.0 |
8.2.0 |
28/05/08 |
RP_40 |
RP-080440 |
0483 |
3 |
HS-SCCH orders for HS-SCCH-less operation |
8.1.0 |
8.2.0 |
28/05/08 |
RP_40 |
RP-080439 |
0485 |
– |
Correction to E-DPCCH gain factor calculation |
8.1.0 |
8.2.0 |
28/05/08 |
RP_40 |
RP-080351 |
0492 |
1 |
Correction to E-DCH control channel timing |
8.1.0 |
8.2.0 |
09/09/08 |
RP_41 |
RP-080672 |
0490 |
1 |
Introduction of the Enhanced Uplink for CELL_FACH state |
8.2.0 |
8.3.0 |
09/09/08 |
RP_41 |
RP-080673 |
0498 |
3 |
Introduction of HS-PDSCH Serving Cell Change Enhancements |
8.2.0 |
8.3.0 |
03/12/08 |
RP_42 |
RP-080989 |
0497 |
4 |
Introduction of Dual-Cell HSDPA Operation on Adjacent Carriers |
8.3.0 |
8.4.0 |
03/12/08 |
RP_42 |
RP-080974 |
0502 |
1 |
Clarification of F-DPCH TPC Combining Rule of cells in the same RLS |
8.3.0 |
8.4.0 |
03/12/08 |
RP_42 |
RP-080988 |
0503 |
1 |
Introduction of HS-PDSCH Serving Cell Change Enhancements |
8.3.0 |
8.4.0 |
03/12/08 |
RP_42 |
RP-080986 |
0504 |
1 |
Corrections in the physical random access procedure for Enhanced Uplink in CELL_FACH State and Idle mode |
8.3.0 |
8.4.0 |
03/12/08 |
RP_42 |
RP-080974 |
0506 |
2 |
Correction to the description of CPC procedures |
8.3.0 |
8.4.0 |
03/12/08 |
RP_42 |
RP-080990 |
0508 |
2 |
Improved EUL power control at UE power limitation |
8.3.0 |
8.4.0 |
03/12/08 |
RP_42 |
RP-080979 |
0509 |
1 |
Typographical error correction in a parameter name in HS-PDSCH reception |
8.3.0 |
8.4.0 |
03/12/08 |
RP_42 |
RP-080986 |
0513 |
– |
Support of HS-DPCCH for Enhanced uplink in CELL_FACH state |
8.3.0 |
8.4.0 |
03/12/08 |
RP_42 |
RP-080978 |
0515 |
– |
Clarification of NIR setting in CQI mapping tables |
8.3.0 |
8.4.0 |
03/12/08 |
RP_42 |
RP-080975 |
0517 |
3 |
Correction to E-DPDCH gain factor interpolation in compressed mode |
8.3.0 |
8.4.0 |
03/12/08 |
RP_42 |
RP-080989 |
0519 |
– |
References to CQI tables for DC-HSDPA |
8.3.0 |
8.4.0 |
03/12/08 |
RP_42 |
RP-080975 |
0523 |
– |
Correction to E-DPDCH gain factor calculation |
8.3.0 |
8.4.0 |
03/12/08 |
RP_42 |
RP-080974 |
0524 |
– |
Clarification of CQI repetition in case of UE DTX |
8.3.0 |
8.4.0 |
03/12/08 |
RP_42 |
RP-080989 |
0528 |
– |
Clarifications to Dual-Cell HSDPA Operation |
8.3.0 |
8.4.0 |
03/03/09 |
RP_43 |
RP-090227 |
0531 |
– |
Editorial correction to UE transmit power control behaviour in case of DTX/DRX |
8.4.0 |
8.5.0 |
03/03/09 |
RP_43 |
RP-090242 |
0534 |
2 |
Corrections of HS-SCCH orders for DC-HSDPA |
8.4.0 |
8.5.0 |
03/03/09 |
RP_43 |
RP-090227 |
0535 |
– |
Clarification of CQI preamble length when switching UE DTX cycle |
8.4.0 |
8.5.0 |
03/03/09 |
RP_43 |
RP-090229 |
0538 |
1 |
Clarification of the source of parameters to HS-DSCH physical layer |
8.4.0 |
8.5.0 |
26/05/09 |
RP_44 |
RP-090525 |
0545 |
1 |
Clarification to the transmission of a combination of ACK and NACK |
8.5.0 |
8.6.0 |
26/05/09 |
RP_44 |
RP-090532 |
0546 |
– |
HS-DSCH serving cell change enhancements with preconfigured secondary cell |
8.5.0 |
8.6.0 |
15/09/09 |
RP_45 |
RP-090885 |
0550 |
1 |
Clarification of CQI transmission when CQI priority changes |
8.6.0 |
8.7.0 |
15/09/09 |
RP_45 |
RP-090886 |
0553 |
1 |
Clarification to support of HS-DSCH related procedures according to MAC-ehs |
8.6.0 |
8.7.0 |
15/09/09 |
RP_45 |
RP-090885 |
0557 |
1 |
Clarification of CPC Enabling Delay |
8.6.0 |
8.7.0 |
15/09/09 |
RP_45 |
RP-090885 |
0559 |
1 |
Clarification of DTX Cycle transitions and UL DPCCH burst transmissions |
8.6.0 |
8.7.0 |
15/09/09 |
RP_45 |
RP-090885 |
0561 |
1 |
Clarification of the start of the CQI_DTX_Timer |
8.6.0 |
8.7.0 |
15/09/09 |
RP_45 |
RP-090883 |
0563 |
1 |
Unequal Power Setting of P-CPICH and S-CPICH |
8.6.0 |
8.7.0 |
15/09/09 |
RP_45 |
RP-090889 |
0568 |
1 |
HS-DPCCH ACK/NACK Power Offset setting for DC-HSDPA |
8.6.0 |
8.7.0 |
18/09/09 |
RP_45 |
RP-090975 |
0548 |
4 |
Introduction of TxAA extension for non-MIMO UEs |
8.7.0 |
9.0.0 |
18/09/09 |
RP_45 |
RP-090974 |
0569 |
– |
Combination of DC-HSDPA with MIMO |
8.7.0 |
9.0.0 |
01/12/09 |
RP_46 |
RP-091170 |
0570 |
5 |
Introduction of DC-HSUPA |
9.0.0 |
9.1.0 |
01/12/09 |
RP_46 |
RP-091171 |
0574 |
3 |
MIMO configuration per downlink frequency in DC-MIMO operation |
9.0.0 |
9.1.0 |
01/12/09 |
RP_46 |
RP-091174 |
0578 |
1 |
Clarification to TxAA extension in dual cell |
9.0.0 |
9.1.0 |
01/12/09 |
RP_46 |
RP-091164 |
0580 |
– |
Clarification of HS-SCCH monitoring |
9.0.0 |
9.1.0 |
01/12/09 |
RP_46 |
RP-091163 |
0582 |
– |
Clarification of CQI nominal timer and CQI DTX TIMER |
9.0.0 |
9.1.0 |
01/12/09 |
RP_46 |
RP-091165 |
0589 |
– |
Table Index Correction |
9.0.0 |
9.1.0 |
16/03/10 |
RP_47 |
RP-100199 |
0592 |
3 |
HSDPA MIMO codebook restriction |
9.1.0 |
9.2.0 |
16/03/10 |
RP_47 |
RP-100200 |
0594 |
– |
Correction to HS-DSCH and HS-SCCH reception in the URA_PCH and CELL_PCH states |
9.1.0 |
9.2.0 |
16/03/10 |
RP_47 |
RP-100206 |
0596 |
1 |
Clarification of MIMO configuration per downlink frequency in DC-MIMO operation |
9.1.0 |
9.2.0 |
16/03/10 |
RP_47 |
RP-100207 |
0597 |
– |
Correction to Applicability of CQI Mapping Table |
9.1.0 |
9.2.0 |
16/03/10 |
RP_47 |
RP-100208 |
0599 |
1 |
Decrease DC-HSPA carrier activation application time to 18 slots |
9.1.0 |
9.2.0 |
14/09/10 |
RP_49 |
RP-100893 |
0604 |
5 |
Clarification of the CQI definition when the UE is configured in MIMO mode |
9.2.0 |
9.3.0 |
14/09/10 |
RP_49 |
RP-100883 |
0607 |
3 |
Clarification of HS-DSCH and HS-SCCH reception in CELL_FACH, CELL_PCH and URA_PCH states |
9.2.0 |
9.3.0 |
14/09/10 |
RP_49 |
RP-100894 |
0614 |
– |
Clarification of E-AGCH/E-RGCH monitoring in a CM gap when DL_DRX_Active is TRUE |
9.2.0 |
9.3.0 |
14/09/10 |
RP_49 |
RP-100898 |
0615 |
2 |
Clarification on the interruption time for DB-HSDPA due to HS-SCCH order (de)activation |
9.2.0 |
9.3.0 |
14/09/10 |
RP_49 |
RP-100897 |
0616 |
– |
Clarification on Secondary_EDCH_Cell_Active upon reception of redundant HS-SCCH order |
9.2.0 |
9.3.0 |
16/09/10 |
RP_49 |
RP-100902 |
0611 |
3 |
Release 10 created with the introduction of 4C HSDPA |
9.3.0 |
10.0.0 |
07/12/10 |
RP_50 |
RP-101318 |
621 |
1 |
Correction of number of received HS-DSCH and HS-SCCH in DC-HSDPA-MIMO and 4C-HSDPA |
10.0.0 |
10.1.0 |
07/12/10 |
RP_50 |
RP-101318 |
622 |
1 |
Clarification on the interruption time for 4C-HSDPA due to HS-SCCH orderred (de)activation |
10.0.0 |
10.1.0 |
07/12/10 |
RP_50 |
RP-101312 |
627 |
– |
Further clarification of E-AGCH/E-RGCH monitoring in CM gap when DL_DRX_Active is TRUE |
10.0.0 |
10.1.0 |
07/12/10 |
RP_50 |
RP-101313 |
631 |
2 |
Clarification of E-DPCCH gain factor calculation in compressed mode |
10.0.0 |
10.1.0 |
07/12/10 |
RP_50 |
RP-101312 |
637 |
1 |
Clarification of discontinuous uplink DPCCH transmission and compressed mode |
10.0.0 |
10.1.0 |
07/12/10 |
RP_50 |
RP-101311 |
641 |
2 |
Correction to the single stream CQI reporting in MIMO mode |
10.0.0 |
10.1.0 |
07/12/10 |
RP_50 |
RP-101310 |
650 |
– |
Clarification of the applicability of the IE Number of PCCH transmissions in CELL_PCH state |
10.0.0 |
10.1.0 |
15/03/11 |
RP_51 |
RP-110251 |
633 |
5 |
Correction to CPC procedure for DC-HSUPA |
10.1.0 |
10.2.0 |
01/06/11 |
RP_52 |
RP-110816 |
653 |
– |
Clarification of activation status when Secondary_Cell_Enabled is changed from 0 to a value not equal to 0 |
10.2.0 |
10.3.0 |
15/09/11 |
RP_53 |
RP-111224 |
656 |
– |
Clarification of when to use Sync A procedure when UE transitions from CELL_FACH to CELL_DCH |
10.3.0 |
10.4.0 |
05/12/11 |
RP_54 |
RP-111670 |
658 |
2 |
CQI reporting for frequency specific compressed mode |
10.4.0 |
10.5.0 |
05/12/11 |
RP_54 |
RP-111671 |
652 |
8 |
Introduction of 8C-HSDPA |
10.5.0 |
11.0.0 |
05/12/11 |
RP_54 |
RP-111672 |
663 |
– |
Introduction of Uplink Closed Loop Transmit Diversity for HSPA |
10.5.0 |
11.0.0 |
28/02/12 |
RP_55 |
RP-120282 |
669 |
– |
Clarification of UL DPCCH Slot Format when DPC_MODE is 1 and CPC is not Enabled |
11.0.0 |
11.1.0 |
28/02/12 |
RP_55 |
RP-120288 |
670 |
– |
Corrections to Uplink Closed Loop Transmit Diversity |
11.0.0 |
11.1.0 |
28/02/12 |
RP_55 |
RP-120281 |
671 |
– |
Further Clarification of when to use Sync A procedure when UE transitions from CELL_FACH to CELL_DCH |
11.0.0 |
11.1.0 |
13/06/12 |
RP_56 |
RP-120741 |
677 |
1 |
Clarification of CLTD Features |
11.1.0 |
11.2.0 |
13/06/12 |
RP_56 |
RP-120741 |
678 |
5 |
Introduction of Timing Diagrams for F-TPICH Operation in UL CLTD |
11.1.0 |
11.2.0 |
13/06/12 |
RP_56 |
RP-120741 |
679 |
2 |
Clarification of TPI timing and F-TPICH transmission for UL CLTD |
11.1.0 |
11.2.0 |
04/09/12 |
RP_57 |
RP-121271 |
685 |
2 |
Introduction of Multiflow |
11.2.0 |
11.3.0 |
04/09/12 |
RP_57 |
RP-121384 |
686 |
1 |
Correction of F-TPICH transmission |
11.2.0 |
11.3.0 |
04/09/12 |
RP_57 |
RP-121384 |
687 |
1 |
Correction to the gain factor definition for S-DPCCH |
11.2.0 |
11.3.0 |
04/09/12 |
RP_57 |
RP-121270 |
690 |
– |
Introduction of Further Enhancements to CELL_FACH |
11.2.0 |
11.3.0 |
04/09/12 |
RP_57 |
RP-121384 |
691 |
– |
Clarification to F-TPICH transmission |
11.2.0 |
11.3.0 |
04/09/12 |
RP_58 |
RP-121845 |
688 |
5 |
Introduction of uplink MIMO and 64QAM |
11.3.0 |
11.4.0 |
04/09/12 |
RP_58 |
RP-121843 |
689 |
5 |
Introduction of 4Tx_HSDPA in 25.214 |
11.3.0 |
11.4.0 |
04/09/12 |
RP_58 |
RP-121841 |
692 |
– |
Clarification of UE procedure for receiving HS-SCCH orders in the CELL_DCH state |
11.3.0 |
11.4.0 |
04/09/12 |
RP_58 |
RP-121841 |
695 |
– |
Clarification of F-TPICH configuration |
11.3.0 |
11.4.0 |
04/09/12 |
RP_58 |
RP-121842 |
697 |
2 |
Clarification to the procedure of NodeB Triggered HS-DPCCH |
11.3.0 |
11.4.0 |
04/09/12 |
RP_58 |
RP-121844 |
699 |
2 |
Clarifications and corrections to HSDPA Multiflow |
11.3.0 |
11.4.0 |
04/09/12 |
RP_58 |
RP-121842 |
700 |
1 |
Clarification of the some aspects of Further Enhancements to CELL_FACH |
11.3.0 |
11.4.0 |
04/09/12 |
RP_58 |
RP-121836 |
701 |
– |
Power scaling handling for Multi-RAB |
11.3.0 |
11.4.0 |
26/02/13 |
RP_59 |
RP-130250 |
702 |
1 |
Correction of HS-DPCCH power offset for four-branch MIMO |
11.4.0 |
11.5.0 |
26/02/13 |
RP_59 |
RP-130359 |
703 |
2 |
Correction to the referenced variable for CELL-FACH enhancement |
11.4.0 |
11.5.0 |
11/06/13 |
RP_60 |
RP-130744 |
707 |
1 |
Correction of HARQ PRE/POST transmission |
11.5.0 |
11.6.0 |
03/09/13 |
MCC clean-up |
11.6.0 |
11.7.0 |
||||
03/09/13 |
RP_61 |
RP-131247 |
709 |
– |
Corrections to Discontinuous downlink reception when the UE is in Multiflow mode |
11.6.0 |
11.7.0 |
03/09/13 |
RP_61 |
RP-131246 |
710 |
– |
Random Access Procedure |
11.6.0 |
11.7.0 |
03/03/14 |
RP_63 |
RP-140409 |
712 |
1 |
Clarification on (de-)activation status of secondary carriers when higher layer indicates a change of HS-DSCH cells |
11.7.0 |
11.8.0 |
10/06/14 |
RP_64 |
RP-140860 |
716 |
2 |
Clarifications to Multiflow Operation |
11.8.0 |
11.9.0 |
10/06/14 |
RP_64 |
RP-140860 |
717 |
1 |
Compressed mode in Multiflow assisting (secondary) serving cell |
11.8.0 |
11.9.0 |
10/06/14 |
RP_64 |
RP-140860 |
718 |
1 |
Correction of DRX operation for Multiflow |
11.8.0 |
11.9.0 |
10/06/14 |
RP_64 |
RP-140861 |
719 |
1 |
Clarification of the power scaling for MIMO dual transport block transmission |
11.8.0 |
11.9.0 |
10/09/14 |
RP_65 |
RP-141475 |
721 |
2 |
Clarifications to Multiflow Operation |
11.9.0 |
11.10.0 |
10/09/14 |
RP_65 |
RP-141476 |
722 |
1 |
Correction to the Four Branch MIMO |
11.9.0 |
11.10.0 |
10/09/14 |
RP_65 |
RP-141480 |
715 |
2 |
Introduction of DCH Enhancements |
11.10.0 |
12.0.0 |
10/09/14 |
RP_65 |
RP-141483 |
720 |
2 |
Introduction of Further EUL Enhancements |
11.10.0 |
12.0.0 |
10/09/14 |
RP_65 |
RP-141481 |
723 |
1 |
Introduction of UMTS Heterogeneous Networks enhancements |
11.10.0 |
12.0.0 |
08/12/14 |
RP_66 |
RP-142102 |
727 |
1 |
Correction to UMTS Hetnet features |
12.0.0 |
12.1.0 |
08/12/14 |
RP_66 |
RP-142103 |
730 |
1 |
Clarification of HS-SCCH orders for Rel-12 features |
12.0.0 |
12.1.0 |
08/12/14 |
RP_66 |
RP-142101 |
731 |
1 |
Correction on DCH Enhancement |
12.0.0 |
12.1.0 |
08/12/14 |
RP_66 |
RP-142103 |
732 |
2 |
Clarifications to Further EUL Enhancements |
12.0.0 |
12.1.0 |
08/12/14 |
RP_66 |
RP-142103 |
734 |
– |
Clarification on the CQI feedback cycle switching procedure |
12.0.0 |
12.1.0 |
09/03/15 |
RP_67 |
RP-150360 |
735 |
1 |
Clarifications to UMTS Heterogeneous Network Enhancements |
12.1.0 |
12.2.0 |
15/06/15 |
RP_68 |
RP-150934 |
738 |
– |
Clarifications to Multiflow |
12.2.0 |
12.3.0 |
14/09/15 |
RP_69 |
RP-151469 |
739 |
– |
Introduction of 3F-4C Multiflow 3F-4C configuration |
12.3.0 |
13.0.0 |
07/12/15 |
RP_70 |
RP-152029 |
741 |
1 |
Clarifications on definitions and CQI reporting in Multiflow 3F-4C configuration |
13.0.0 |
13.1.0 |
07/12/15 |
RP_70 |
RP-152039 |
743 |
1 |
Introduction of downlink TPC enhancements for UMTS |
13.0.0 |
13.1.0 |
Change history |
|||||||
Date |
Meeting |
TDoc |
CR |
Rev |
Cat |
Subject/Comment |
New version |
2016-03 |
RP-71 |
RP-160368 |
0746 |
1 |
F |
Clarification on the availability of the F-DPCH for Algorithm1 and 2, within the first phase of the downlink synchronization status evaluation |
13.2.0 |
2016-03 |
RP-71 |
RP-160366 |
0745 |
1 |
F |
Correction of Rel-13 Downlink TPC Enhancements |
13.2.0 |
2016-06 |
RP-72 |
RP-161144 |
0748 |
F |
Clarifications on DCH enhancements feature |
13.3.0 |
|
2016-07 |
MCC clean-up by removing unecessary comments left in sections 5.1.2.2.4.2 and 5.1.2.2.4.3 |
13.3.1 |
|||||
2016-09 |
RP-73 |
RP-161568 |
0750 |
– |
A |
Clarifications on UL Discontinuous Transmission with DCH enhancements (Rel. 13) |
13.4.0 |
2016-09 |
RP-73 |
RP-161568 |
0751 |
1 |
A |
Correction of DCH enhancements |
13.4.0 |
2016-09 |
RP-73 |
RP-161564 |
0753 |
1 |
F |
Correction of DCH enhancements |
13.4.0 |
2016-09 |
RP-73 |
RP-161568 |
0755 |
– |
A |
Editorial clarification on the definitions of “UL DPCH 10ms Mode” and “UL DPCH 20ms Mode” of DCH enhancements for UMTS |
13.4.0 |
2016-12 |
RP-74 |
RP-162354 |
0758 |
– |
B |
UE Procedures for HS-SCCH DRx feature in enhanced Cell Fach |
14.0.0 |
2017-03 |
RP-75 |
RP-170614 |
0759 |
– |
F |
Clarification on the TTI switching for single cell E-DCH and dual cell E-DCH |
14.1.0 |
2017-09 |
RP-77 |
RP-171592 |
0760 |
2 |
B |
Introduction of the triggering mechanisms for the simplified HS-SCCH type 1 operation |
15.0.0 |
2020-07 |
RP-88e |
– |
– |
– |
– |
Upgrade to Rel-16 version without technical change |
16.0.0 |
2022-03 |
RP-95e |
– |
– |
– |
– |
Upgrade to Rel-17 version without technical change |
17.0.0 |