A.5.4 Cell Re-selection in CELL_FACH
25.1233GPPRelease 17Requirements for support of radio resource management (TDD)TS
A.5.4.1 3.84 Mcps TDD option
A.5.4.1.1 Scenario 1: Re-selection to intra-frequency TDD cell
A.5.4.1.1.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the cell re-selection delay in CELL_FACH state in the single carrier case reported in section 5.4.2.1.1. The test parameters are given in Tables A.5.4.1 to A.5.4.4.
Table A.5.4.1: General test parameters for Cell Re-selection in CELL_FACH
Parameter |
Unit |
Value |
Comment |
|
Initial condition |
Active cell |
Cell1 |
||
Neighbour cells |
Cell2, Cell3,Cell4, Cell5, Cell6 |
|||
Final condition |
Active cell |
Cell2 |
||
HCS |
Not used |
|||
UE_TXPWR_MAX_RACH |
dBm |
21 |
The value shall be used for all cells in the test. |
|
Qrxlevmin |
dBm |
-102 |
The value shall be used for all cells in the test. |
|
Access Service Class (ASC#0) |
– |
1 |
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test. |
|
TSI |
s |
1,28 |
The value shall be used for all cells in the test. |
|
T1 |
s |
15 (initial), |
||
T2 |
s |
5 |
Table A.5.4.2: Physical channel parameters for S-CCPCH.
Parameter |
Unit |
Level |
Channel bit rate |
Kbps |
24,4 |
Channel symbol rate |
Ksps |
12,2 |
Slot Format # |
– |
0 |
Frame allocation |
– |
Continuous frame allocation |
Midamble allocation |
– |
Default Midamble |
Table A.5.4.3: Transport channel parameters for S-CCPCH
Parameter |
FACH |
Transport Channel Number |
1 |
Transport Block Size |
240 |
Transport Block Set Size |
240 |
Transmission Time Interval |
20 ms |
Type of Error Protection |
Convolutional Coding |
Coding Rate |
½ |
Rate Matching attribute |
256 |
Size of CRC |
16 |
Table A.5.4.4: Cell specific test parameters for Cell Re-selection in CELL_FACH
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
|||||||||
Timeslot Number |
0 |
8 |
0 |
8 |
0 |
8 |
|||||||
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
||
UTRA RF Channel Number |
Channel 1 |
Channel 1 |
Channel 1 |
||||||||||
PCCPCH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
||||||
SCH_Ec/Ior |
dB |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
SCH_toffset |
0 |
0 |
0 |
0 |
5 |
5 |
5 |
5 |
10 |
10 |
10 |
10 |
|
PICH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
||||||
OCNS_Ec/Ior |
dB |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
|
dB |
9 |
7 |
9 |
7 |
7 |
9 |
7 |
9 |
-1 |
-1 |
-1 |
-1 |
PCCPCH RSCP |
dBm |
-64 |
-66 |
-66 |
-64 |
-74 |
-74 |
||||||
Qoffset1s,n |
dB |
C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1,C6:0 |
C2, C1: 0; C2, C3:0; C2,C4:0 C2, C5: 0; C2, C6:0 |
C3, C1: 0; C3, C2:0; C3,C4:0 C3, C5: 0; C3, C6:0 |
|||||||||
Qhyst1s |
dB |
0 |
0 |
0 |
|||||||||
Treselection |
0 |
0 |
0 |
||||||||||
Sintrasearch |
dB |
not sent |
not sent |
not sent |
|||||||||
FACH measurement occasion info |
not sent |
not sent |
not sent |
||||||||||
|
dBm/ 3,84 MHz |
-70 |
|||||||||||
Propagation Condition |
AWGN |
||||||||||||
Cell 4 |
Cell 5 |
Cell 6 |
|||||||||||
Timeslot |
0 |
8 |
0 |
8 |
0 |
8 |
|||||||
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
||
UTRA RF Channel Number |
Channel 1 |
Channel 1 |
Channel 1 |
||||||||||
PCCPCH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
||||||
SCH_Ec/Ior |
dB |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
SCH_toffset |
15 |
15 |
15 |
15 |
20 |
20 |
20 |
20 |
25 |
25 |
25 |
25 |
|
PICH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
||||||
OCNS_Ec/Ior |
dB |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
|
dB |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
PCCPCH RSCP |
dBm |
-74 |
-74 |
-74 |
-74 |
-74 |
-74 |
||||||
Qoffset1s,n |
dB |
C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0 |
C5, C1: 0; C5, C2:0; C5,C3:0 C5, C4:0; C5, C6:0 |
C6, C1: 0; C6, C2:0; C6,C3:0 C6, C4:0; C6, C5:0 |
|||||||||
Qhyst1s |
dB |
0 |
0 |
0 |
|||||||||
Treselection |
0 |
0 |
0 |
||||||||||
Sintrasearch |
dB |
not sent |
not sent |
not sent |
|||||||||
FACH measurement occasion info |
not sent |
not sent |
not sent |
||||||||||
|
dBm/ 3,84 MHz |
-70 |
|||||||||||
Propagation Condition |
AWGN |
NOTE: S-CCPCH shall not be located in TS0.
A.5.4.1.1.2 Test Requirements
The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send the CELL UPDATE message with cause value "cell reselection" in cell 2.
The cell re-selection delay shall be less than 2,5 s.
The rate of correct cell re-selections observed during repeated tests shall be at least 90%.
A.5.4.1.2 Scenario 2: Re-selection to inter-frequency TDD cell
A.5.4.1.2.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the cell re-selection delay in CELL_FACH state in the multi carrier case reported in section 5.4.2.1.2. The test parameters are given in Tables A.5.4.5 to A.5.4.8.
Table A.5.4.5: General test parameters for Cell Re-selection in CELL_FACH
Parameter |
Unit |
Value |
Comment |
|
Initial condition |
Active cell |
Cell1 |
||
Neighbour cells |
Cell2, Cell3,Cell4, Cell5, Cell6 |
|||
Final condition |
Active cell |
Cell2 |
||
HCS |
Not used |
|||
UE_TXPWR_MAX_RACH |
dBm |
21 |
The value shall be used for all cells in the test. |
|
Qrxlevmin |
dBm |
-102 |
The value shall be used for all cells in the test. |
|
Access Service Class (ASC#0) |
– |
1 |
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test. |
|
TSI |
s |
1,28 |
The value shall be used for all cells in the test. |
|
T1 |
s |
15 (initial), |
||
T2 |
s |
5 |
Table A.5.4.6: Physical channel parameters for S-CCPCH.
Parameter |
Unit |
Level |
Channel bit rate |
Kbps |
24,4 |
Channel symbol rate |
Ksps |
12,2 |
Slot Format # |
– |
0 |
Frame allocation |
– |
Continuous frame allocation |
Midamble allocation |
– |
Default Midamble |
Table A.5.4.7: Transport channel parameters for S-CCPCH
Parameter |
FACH |
Transport Channel Number |
1 |
Transport Block Size |
240 |
Transport Block Set Size |
240 |
Transmission Time Interval |
20 ms |
Type of Error Protection |
Convolutional Coding |
Coding Rate |
½ |
Rate Matching attribute |
256 |
Size of CRC |
16 |
Table A.5.4.8: Cell specific test parameters for Cell Re-selection in CELL_FACH
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
|||||||||
Timeslot Number |
0 |
8 |
0 |
8 |
0 |
8 |
|||||||
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
||
UTRA RF Channel Number |
Channel 1 |
Channel 2 |
Channel 1 |
||||||||||
PCCPCH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
||||||
SCH_Ec/Ior |
dB |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
SCH_toffset |
0 |
0 |
0 |
0 |
5 |
5 |
5 |
5 |
10 |
10 |
10 |
10 |
|
PICH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
||||||
OCNS_Ec/Ior |
dB |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
|
dB |
9 |
3 |
9 |
3 |
3 |
9 |
3 |
9 |
-1 |
-1 |
-1 |
-1 |
PCCPCH RSCP |
dBm |
-64 |
-70 |
-70 |
-64 |
-74 |
-74 |
||||||
Qoffset1s,n |
dB |
C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1,C6:0 |
C2, C1: 0; C2, C3:0; C2,C4:0 C2, C5: 0; C2, C6:0 |
C3, C1: 0; C3, C2:0; C3,C4:0 C3, C5: 0; C3, C6:0 |
|||||||||
Qhyst1s |
dB |
0 |
0 |
0 |
|||||||||
Treselection |
0 |
0 |
0 |
||||||||||
Sintrasearch |
dB |
not sent |
not sent |
not sent |
|||||||||
Sintersearch |
dB |
not sent |
not sent |
not sent |
|||||||||
FACH measurement occasion info |
not sent |
not sent |
not sent |
||||||||||
Inter-frequency TDD measurement indicator |
TRUE |
TRUE |
TRUE |
||||||||||
|
dBm/ 3,84 MHz |
-70 |
|||||||||||
Propagation Condition |
AWGN |
||||||||||||
Cell 4 |
Cell 5 |
Cell 6 |
|||||||||||
Timeslot |
0 |
8 |
0 |
8 |
0 |
8 |
|||||||
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
||
UTRA RF Channel Number |
Channel 1 |
Channel 2 |
Channel 2 |
||||||||||
PCCPCH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
||||||
SCH_Ec/Ior |
dB |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
SCH_toffset |
15 |
15 |
15 |
15 |
20 |
20 |
20 |
20 |
25 |
25 |
25 |
25 |
|
PICH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
||||||
OCNS_Ec/Ior |
dB |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
|
dB |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
PCCPCH RSCP |
dBm |
-74 |
-74 |
-74 |
-74 |
-74 |
-74 |
||||||
Qoffset1s,n |
dB |
C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0 |
C5, C1: 0; C5, C2:0; C5,C3:0 C5, C4:0; C5, C6:0 |
C6, C1: 0; C6, C2:0; C6,C3:0 C6, C4:0; C6, C5:0 |
|||||||||
Qhyst1s |
dB |
0 |
0 |
0 |
|||||||||
Treselection |
0 |
0 |
0 |
||||||||||
Sintrasearch |
dB |
not sent |
not sent |
not sent |
|||||||||
Sintersearch |
dB |
not sent |
not sent |
not sent |
|||||||||
FACH measurement occasion info |
not sent |
not sent |
not sent |
||||||||||
Inter-frequency TDD measurement indicator |
TRUE |
TRUE |
TRUE |
||||||||||
|
dBm/ 3,84 MHz |
-70 |
|||||||||||
Propagation Condition |
AWGN |
||||||||||||
NOTE: S-CCPCH shall not be located in TS0. |
A.5.4.1.2.2 Test Requirements
The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send the CELL UPDATE message with cause value "cell reselection" in cell 2.
The cell re-selection delay shall be less than 3 s.
The rate of correct cell re-selections observed during repeated tests shall be at least 90%.
A.5.4.2 1.28 Mcps TDD option
A.5.4.2.1 Re-selection to intra-frequency TDD cell
A.5.4.2.1.1 Test purpose and Environment
The purpose of this test is to verify the requirement for the cell re-selection delay in CELL_FACH state in the case reported in section 5.4.3.2.1.
The test parameters are given in Tables A.5.4.9to A.5.4.12
Table A.5.4.9: General test parameters for Cell Re-selection in CELL_FACH
Parameter |
Unit |
Value |
Comment |
|
initial condition |
Active cell |
Cell1 |
||
Neighbour cells |
Cell2, Cell3,Cell4, Cell5, Cell6 |
|||
final condition |
Active cell |
Cell2 |
||
HCS |
Not used |
|||
UE_TXPWR_MAX_RACH |
dBm |
21 |
The value shall be used for all cells in the test. |
|
Qrxlevmin |
dBm |
-103 |
The value shall be used for all cells in the test. |
|
Access Service Class (ASC#0) |
1 |
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test. |
||
TSI |
s |
1.28 |
The value shall be used for all cells in the test. |
|
T1 |
s |
15 (initial), 5 (repetition) |
||
T2 |
s |
5 |
Table A.5.4.10: Physical channel parameters for S-CCPCH.
Parameter |
Unit |
Level |
Channel bit rate |
kbps |
35.2 |
Channel symbol rate |
ksps |
17.6 |
Slot Format # |
– |
0; 2 |
Frame allocation |
– |
Continuous frame allocation |
Midamble allocation |
– |
Common Midamble |
Table A.5.4.11: Transport channel parameters for S-CCPCH
Parameter |
FACH |
Transport Channel Number |
1 |
Transport Block Size |
240 |
Transport Block Set Size |
240 |
Transmission Time Interval |
20 ms |
Type of Error Protection |
Convolution Coding |
Coding Rate |
½ |
Rate Matching attribute |
256 |
Size of CRC |
16 |
Table A.5.4.12: Cell specific test parameters for Cell Re-selection in CELL_FACH
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
|||||||||||||
Timeslot Number |
0 |
DWPTS |
0 |
DWPTS |
0 |
DWPTS |
|||||||||||
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
||||||
UTRA RF Channel Number (NOTE 2) |
Channel 1 |
Channel 1 |
Channel 1 |
||||||||||||||
PCCPCH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
||||||||||
DwPCH_Ec/Ior |
dB |
0 |
0 |
0 |
0 |
0 |
0 |
||||||||||
OCNS_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
||||||||||
|
dB |
10 |
7 |
10 |
7 |
7 |
10 |
7 |
10 |
-1 |
-1 |
-1 |
-1 |
||||
PCCPCH RSCP |
dBm |
-63 |
-66 |
-66 |
-63 |
-74 |
-74 |
||||||||||
Qoffset1s,n |
dB |
C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1,C6:0 |
C2, C1: 0; C2, C3:0; C2,C4:0 C2, C5: 0; C2, C6:0 |
C3, C1: 0; C3, C2:0; C3,C4:0 C3, C5: 0; C3, C6:0 |
|||||||||||||
Qhyst1s |
dB |
0 |
0 |
0 |
|||||||||||||
Treselection |
0 |
0 |
0 |
||||||||||||||
Sintrasearch |
dB |
not sent |
not sent |
not sent |
|||||||||||||
FACH measurement occasion info |
not sent |
not sent |
not sent |
||||||||||||||
Cell 4 |
Cell 5 |
Cell 6 |
|||||||||||||||
Timeslot |
0 |
DWPTS |
0 |
DWPTS |
0 |
DWPTS |
|||||||||||
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
||||||
UTRA RF Channel Number (NOTE 2) |
Channel 1 |
Channel 1 |
Channel 1 |
||||||||||||||
PCCPCH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
||||||||||
DwPCH_Ec/Ior |
dB |
0 |
0 |
0 |
0 |
0 |
0 |
||||||||||
OCNS_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
||||||||||
|
dB |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
||||
PCCPCH RSCP |
dBm |
-74 |
-74 |
-74 |
-74 |
-74 |
-74 |
||||||||||
Qoffset1s,n |
dB |
C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0 |
C5, C1: 0; C5, C2:0; C5,C3:0 C5, C4:0; C5, C6:0 |
C6, C1: 0; C6, C2:0; C6,C3:0 C6, C4:0; C6, C5:0 |
|||||||||||||
Qhyst1s |
dB |
0 |
0 |
0 |
|||||||||||||
Treselection |
0 |
0 |
0 |
||||||||||||||
Sintrasearch |
dB |
not sent |
not sent |
not sent |
|||||||||||||
FACH measurement occasion info |
not sent |
not sent |
not sent |
||||||||||||||
|
dBm/1.28 MHz |
-70 |
|||||||||||||||
Propagation Condition |
AWGN |
||||||||||||||||
NOTE 1: S-CCPCH is located in an other downlink TS than TS0. NOTE 2: In the case of multi-frequency network,the UTRA RF Channel Number is the primary frequency’s channel number. |
A.5.4.2.1.2 Test Requirements
The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send SYNCH-UL sequence in the UpPTS for sending the CELL UPDATE message with cause value "cell reselection" in cell 2.
The cell re-selection delay shall be less than 1.6 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE:
The cell re-selection delay can be expressed as:
ms
where:
TMeasurement Period Intra Specified in 8.4A.2.2.2 gives 200ms for this test case.
TSI Time required for receiving all the relevant system information data according to the reception procedure and the RRC procedure delay of system information blocks defined in 25.331 for a UTRAN cell (ms). 1280 ms is assumed in this test case.
TRA The additional delay caused by the random access procedure described in TS25.224. In this test case the persistence value is 1 thus TRA is set to 35ms in the test case.
This gives a total of 1.545s, allow 1.6s in the test case.
A.5.4.2.2 Re-selection to inter-frequency TDD cell
A.5.4.2.2.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the cell re-selection delay in CELL_FACH state in section 5.4.3.2.2. The test parameters are given in Tables A.5.4.13 to A.5.4.16
Table A.5.4.13: General test parameters for Cell Re-selection in CELL_FACH
Parameter |
Unit |
Value |
Comment |
|
initial condition |
Active cell |
Cell1 |
||
Neighbour cells |
Cell2, Cell3,Cell4, Cell5, Cell6 |
|||
final condition |
Active cell |
Cell2 |
||
HCS |
Not used |
|||
UE_TXPWR_MAX_RACH |
dBm |
21 |
The value shall be used for all cells in the test. |
|
Qrxlevmin |
dBm |
-103 |
The value shall be used for all cells in the test. |
|
Access Service Class (ASC#0) |
1 |
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test. |
||
TSI |
s |
1.28 |
The value shall be used for all cells in the test. |
|
T1 |
s |
15 (initial), 5 (repetition) |
||
T2 |
s |
5 |
Table A.5.4.14: Physical channel parameters for S-CCPCH.
Parameter |
Unit |
Level |
Channel bit rate |
kbps |
35.2 |
Channel symbol rate |
ksps |
17.6 |
Slot Format # |
– |
0; 2 |
Frame allocation |
– |
Continuous frame allocation |
Midamble allocation |
– |
Common Midamble |
Table A.5.4.15: Transport channel parameters for S-CCPCH
Parameter |
FACH |
Transport Channel Number |
1 |
Transport Block Size |
240 |
Transport Block Set Size |
240 |
Transmission Time Interval |
20 ms |
Type of Error Protection |
Convolution Coding |
Coding Rate |
½ |
Rate Matching attribute |
256 |
Size of CRC |
16 |
Table A.5.4.16: Cell specific test parameters for Cell re-selection in CELL_FACH state
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
||||||||||||
Timeslot Number |
0 |
DWPTS |
0 |
DWPTS |
0 |
DWPTS |
||||||||||
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
|||||
UTRA RF Channel Number (NOTE 2) |
Channel 1 |
Channel 2 |
Channel 1 |
|||||||||||||
PCCPCH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
|||||||||
DwPCH_Ec/Ior |
dB |
0 |
0 |
0 |
0 |
0 |
0 |
|||||||||
OCNS_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
|||||||||
|
dB |
10 |
4 |
10 |
4 |
4 |
10 |
4 |
10 |
-1 |
-1 |
-1 |
-1 |
|||
PCCPCH RSCP |
dBm |
-63 |
-69 |
-69 |
-63 |
-74 |
-74 |
|||||||||
Qoffset1s,n |
dB |
C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1,C6:0 |
C2, C1: 0; C2, C3:0; C2,C4:0 C2, C5: 0; C2:C6:0 |
C3, C1: 0; C3, C2:0; C3,C4:0 C3, C5: 0; C3:C6:0 |
||||||||||||
Qhyst1s |
dBm |
0 |
0 |
0 |
||||||||||||
Treselection |
s |
0 |
0 |
0 |
||||||||||||
Sintrasearch |
dB |
not sent |
not sent |
not sent |
||||||||||||
Sintersearch |
dB |
not sent |
not sent |
not sent |
||||||||||||
FACH measurement occasion info |
not sent |
not sent |
not sent |
|||||||||||||
FACH measurement occasion cycle length |
4 |
4 |
4 |
|||||||||||||
Inter-frequency TDD measurement indicator |
TRUE |
TRUE |
TRUE |
|||||||||||||
Inter-frequency FDD measurement indicator |
FALSE |
FALSE |
FALSE |
|||||||||||||
Cell 4 |
Cell 5 |
Cell 6 |
||||||||||||||
Timeslot |
0 |
DWPTS |
0 |
DWPTS |
0 |
DWPTS |
||||||||||
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
|||||
UTRA RF Channel Number (NOTE 2) |
Channel 1 |
Channel 2 |
Channel 2 |
|||||||||||||
PCCPCH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
|||||||||
DwPCH_Ec/Ior |
dB |
0 |
0 |
0 |
0 |
0 |
0 |
|||||||||
OCNS_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
|||||||||
|
dB |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
|||
PCCPCH RSCP |
dBm |
-74 |
-74 |
-74 |
-74 |
-74 |
-74 |
|||||||||
Qoffset1s,n |
dB |
C4, C1: 0; C4, C2:0; C4,C3:0; C4, C5:0; C4:C6:0 |
C5, C1: 0; C5, C2:0; C5,C3:0 C5, C4:0; C5:C6:0 |
C6, C1: 0; C6, C2:0; C6,C3:0 C6, C4:0; C6:C5:0 |
||||||||||||
Qhyst1s |
dB |
0 |
0 |
0 |
||||||||||||
Treselection |
s |
0 |
0 |
0 |
||||||||||||
Sintrasearch |
dB |
not sent |
not sent |
not sent |
||||||||||||
Sintersearch |
dB |
not sent |
not sent |
not sent |
||||||||||||
FACH measurement occasion info |
not sent |
not sent |
not sent |
|||||||||||||
FACH measurement occasion cycle length |
4 |
4 |
4 |
|||||||||||||
Inter-frequency TDD measurement indicator |
TRUE |
TRUE |
TRUE |
|||||||||||||
Inter-frequency FDD measurement indicator |
FALSE |
FALSE |
FALSE |
|||||||||||||
|
dBm/ 1.28 MHz |
-70 |
||||||||||||||
Propagation Condition |
AWGN |
|||||||||||||||
NOTE 1: S-CCPCH is located in an other downlink TS than TS0. NOTE 2: In the case of multi-frequency network,the UTRA RF Channel Number is the primary frequency’s channel number. |
A.5.4.2.2.2 Test Requirements
The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send SYNCH-UL sequence in the UpPTS for sending the CELL UPDATE message with cause value "cell reselection" in cell 2.
The cell re-selection delay shall be less than 2 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: The cell re-selection delay can be expressed as:
ms,
where:
Tmeasurement inter is specified in 8.4A.2.3.2 gives 480ms for this test case.
TSI Time required for receiving all the relevant system information data according to the reception procedure and the RRC procedure delay of system information blocks defined in 25.331 for a UTRAN cell (ms). 1280 ms is assumed in this test case.
TRA The additional delay caused by the random access procedure described in TS25.224. In this test case the persistence value is 1 thus TRA is set to 35ms in the test case.
This gives a total of 1.825s, allow 1.9s in the test case.
A.5.4.2.3 Re-selection to GSM cell
A.5.4.2.3.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the cell re-selection delay in CELL_FACH state in section 5.4.3.2.4.
This scenario implies the presence of 1 UTRAN serving cell, and 1 GSM cell to be re-selected. The UE is requested to monitor neighbouring cells on 1 UMTS carrier and 6 GSM cells. Test parameters are given in Table, A.5.4.16A, A.5.4.16B, A.5.4.16C, A.5.4.16D, A.5.4.16E.
Table A.5.4.16A: General test parameters for UTRAN to GSM Cell Re-selection
Parameter |
Unit |
Value |
Comment |
|
Initial condition |
Active cell |
Cell1 |
||
Neighbour cell |
Cell2 |
|||
Final condition |
Active cell |
Cell2 |
||
HCS |
Not used |
|||
UE_TXPWR_MAX_RACH |
dBm |
21 |
The value shall be used for all cells in the test |
|
Qrxlevmin |
dBm |
-103 |
The value shall be used for all cells in the test |
|
Access Service Class (ASC#0) ‑ Persistence value |
1 |
The value shall be used for all cells in the test |
||
TSI |
s |
1,28 |
||
T1 |
s |
15 |
||
T2 |
s |
15 |
The transport and physical parameters of the S-CCPCH carrying the FACH are defined in Table A.5.4.16B and Table A.5.4.16C.
Table A.5.4.16B: Physical channel parameters for S-CCPCH.
Parameter |
Unit |
Level |
Channel bit rate |
kbps |
35.2 |
Channel symbol rate |
ksps |
17.6 |
Slot Format #I |
– |
0; 2 |
Frame allocation |
– |
Continuous frame allocation |
Midamble allocation |
– |
Common Midamble |
Table A.5.4.16C: Transport channel parameters for S-CCPCH
Parameter |
FACH |
Transport Channel Number |
1 |
Transport Block Size |
240 |
Transport Block Set Size |
240 |
Transmission Time Interval |
20 ms |
Type of Error Protection |
Convolution Coding |
Coding Rate |
½ |
Rate Matching attribute |
256 |
Size of CRC |
16 |
Table A.5.4.16D: Cell re-selection UTRAN TDD 1,28 Mcps Option to GSM cell case (cell 1)
Parameter |
Unit |
Cell 1 (UTRA) |
||||
Timeslot Number |
0 |
DwPTS |
||||
T1 |
T2 |
T1 |
T2 |
|||
UTRA RF Channel Number |
Channel 1 |
Channel 1 |
||||
PCCPCH_Ec/Ior |
dB |
-3 |
-3 |
|||
DwPCH_Ec/Ior |
dB |
0 |
0 |
|||
OCNS_Ec/Ior |
dB |
-3 |
-3 |
|||
|
dB |
6 |
6 |
6 |
6 |
|
|
dBm/1,28 MHz |
-80 |
||||
PCCPCH RSCP |
dBm |
-77 |
||||
Propagation Condition |
AWGN |
AWGN |
||||
Treselection |
s |
0 |
||||
SsearchRAT |
dB |
Not sent |
||||
Qrxlevmin |
dBm |
-103 |
||||
Qoffset1s,n |
dB |
C1, C2: 0 |
||||
Qhyst1s |
dB |
0 |
Table A.5.4.16E: Cell re-selection UTRAN to GSM cell case (cell 2)
Parameter |
Unit |
Cell 2 (GSM) |
|
T1 |
T2 |
||
Absolute RF Channel Number |
ARFCN 1 |
||
RXLEV |
dBm |
-90 |
-70 |
RXLEV_ACCESS_ |
dBm |
-103 |
|
MS_TXPWR_MAX_ |
dBm |
33 |
|
Qsearch_I |
– |
always |
A.5.4.2.3.2 Test Requirements
The cell re-selection delay is defined as the time from when the cell quality levels change to the moment when this change makes the UE reselect a better ranked cell, and starts to send CHANNEL REQUEST message to perform a Location update to the new cell.
This test is for the case where the UE camps on a 1,28 Mcps TDD cell and reselects to a GSM cell.
The requirements and this test apply to UEs supporting both 1,28 Mcps TDD and GSM.
The cell re-selection delay shall be less than 7.5 s.
The rate of correct cell reselections observed during repeated tests shall be at least 90%.
NOTE: Treselection GSM = 40 + Tidentify GSM + Tmeasurement GSM + TBCCH + TRA, where:
TRA = The additional delay caused by the random access procedure,10ms.
Tidentify GSM Specified in TS 25.123 ,here it is 5000ms.
TmeasureGSM 480ms according to Table 4.1A in section 4.2.
TBCCH Maximum time allowed to read BCCH data from GSM cell.
The maximum time allowed to read the BCCH data, when being synchronized to a BCCH carrier, is 1.9 s.
This gives a total of 7.43s, thus allow 7.5s.
A.5.4.3 7.68 Mcps TDD option
A.5.4.3.1 Scenario 1: TDD/TDD cell re-selection single carrier case
A.5.4.3.1.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the cell re-selection delay in CELL_FACH state in the single carrier case reported in section 5.4.4.1.1. The test parameters are given in Tables A.5.4.17 to A.5.4.20.
Table A.5.4.17: General test parameters for Cell Re-selection in CELL_FACH
Parameter |
Unit |
Value |
Comment |
|
Initial condition |
Active cell |
Cell1 |
||
Neighbour cells |
Cell2, Cell3,Cell4, Cell5, Cell6 |
|||
Final condition |
Active cell |
Cell2 |
||
HCS |
Not used |
|||
UE_TXPWR_MAX_RACH |
dBm |
21 |
The value shall be used for all cells in the test. |
|
Qrxlevmin |
dBm |
-102 |
The value shall be used for all cells in the test. |
|
Access Service Class (ASC#0) |
– |
1 |
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test. |
|
TSI |
s |
1,28 |
The value shall be used for all cells in the test. |
|
T1 |
s |
15 (initial), |
||
T2 |
s |
5 |
Table A.5.4.18: Physical channel parameters for S-CCPCH.
Parameter |
Unit |
Level |
Channel bit rate |
Kbps |
24,4 |
Channel symbol rate |
Ksps |
12,2 |
Slot Format # |
– |
0 |
Frame allocation |
– |
Continuous frame allocation |
Midamble allocation |
– |
Default Midamble |
Table A.5.4.19: Transport channel parameters for S-CCPCH
Parameter |
FACH |
Transport Channel Number |
1 |
Transport Block Size |
240 |
Transport Block Set Size |
240 |
Transmission Time Interval |
20 ms |
Type of Error Protection |
Convolutional Coding |
Coding Rate |
½ |
Rate Matching attribute |
256 |
Size of CRC |
16 |
Table A.5.4.20: Cell specific test parameters for Cell Re-selection in CELL_FACH
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
|||||||||||||
Timeslot Number |
0 |
8 |
0 |
8 |
0 |
8 |
|||||||||||
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
||||||
UTRA RF Channel Number |
Channel 1 |
Channel 1 |
Channel 1 |
||||||||||||||
PCCPCH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
||||||||||
SCH_Ec/Ior |
dB |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
||||
SCH_toffset |
0 |
0 |
0 |
0 |
5 |
5 |
5 |
5 |
10 |
10 |
10 |
10 |
|||||
PICH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
||||||||||
OCNS_Ec/Ior |
dB |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
||||
|
dB |
9 |
7 |
9 |
7 |
7 |
9 |
7 |
9 |
-1 |
-1 |
-1 |
-1 |
||||
PCCPCH RSCP |
dBm |
-64 |
-66 |
-66 |
-64 |
-74 |
-74 |
||||||||||
Qoffset1s,n |
dB |
C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1,C6:0 |
C2, C1: 0; C2, C3:0; C2,C4:0 C2, C5: 0; C2, C6:0 |
C3, C1: 0; C3, C2:0; C3,C4:0 C3, C5: 0; C3, C6:0 |
|||||||||||||
Qhyst1s |
dB |
0 |
0 |
0 |
|||||||||||||
Treselection |
0 |
0 |
0 |
||||||||||||||
Sintrasearch |
dB |
not sent |
not sent |
not sent |
|||||||||||||
FACH measurement occasion info |
not sent |
not sent |
not sent |
||||||||||||||
|
dBm/7,68 MHz |
-70 |
|||||||||||||||
Propagation Condition |
AWGN |
||||||||||||||||
Cell 4 |
Cell 5 |
Cell 6 |
|||||||||||||||
Timeslot |
0 |
8 |
0 |
8 |
0 |
8 |
|||||||||||
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
||||||
UTRA RF Channel Number |
Channel 1 |
Channel 1 |
Channel 1 |
||||||||||||||
PCCPCH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
||||||||||
SCH_Ec/Ior |
dB |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
||||
SCH_toffset |
15 |
15 |
15 |
15 |
20 |
20 |
20 |
20 |
25 |
25 |
25 |
25 |
|||||
PICH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
||||||||||
OCNS_Ec/Ior |
dB |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
||||
|
dB |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
||||
PCCPCH RSCP |
dBm |
-74 |
-74 |
-74 |
-74 |
-74 |
-74 |
||||||||||
Qoffset1s,n |
dB |
C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0 |
C5, C1: 0; C5, C2:0; C5,C3:0 C5, C4:0; C5, C6:0 |
C6, C1: 0; C6, C2:0; C6,C3:0 C6, C4:0; C6, C5:0 |
|||||||||||||
Qhyst1s |
dB |
0 |
0 |
0 |
|||||||||||||
Treselection |
0 |
0 |
0 |
||||||||||||||
Sintrasearch |
dB |
not sent |
not sent |
not sent |
|||||||||||||
FACH measurement occasion info |
not sent |
not sent |
not sent |
||||||||||||||
|
dBm/7,68 MHz |
-70 |
|||||||||||||||
Propagation Condition |
AWGN |
NOTE: S-CCPCH shall not be located in TS0.
A.5.4.3.1.2 Test Requirements
The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send the CELL UPDATE message with cause value "cell reselection" in cell 2.
The cell re-selection delay shall be less than 2,5 s.
The rate of correct cell re-selections observed during repeated tests shall be at least 90%.
A.5.4.3.2 Scenario 2: TDD/TDD cell re-selection multi carrier case
A.5.4.1.2.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the cell re-selection delay in CELL_FACH state in the multi carrier case reported in section 5.4.4.1.2. The test parameters are given in Tables A.5.4.21 to A.5.4.24.
Table A.5.4.21: General test parameters for Cell Re-selection in CELL_FACH
Parameter |
Unit |
Value |
Comment |
|
Initial condition |
Active cell |
Cell1 |
||
Neighbour cells |
Cell2, Cell3,Cell4, Cell5, Cell6 |
|||
Final condition |
Active cell |
Cell2 |
||
HCS |
Not used |
|||
UE_TXPWR_MAX_RACH |
dBm |
21 |
The value shall be used for all cells in the test. |
|
Qrxlevmin |
dBm |
-102 |
The value shall be used for all cells in the test. |
|
Access Service Class (ASC#0) |
– |
1 |
Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test. |
|
TSI |
s |
1,28 |
The value shall be used for all cells in the test. |
|
T1 |
s |
15 (initial), |
||
T2 |
s |
5 |
Table A.5.4.22: Physical channel parameters for S-CCPCH.
Parameter |
Unit |
Level |
Channel bit rate |
Kbps |
24,4 |
Channel symbol rate |
Ksps |
12,2 |
Slot Format # |
– |
0 |
Frame allocation |
– |
Continuous frame allocation |
Midamble allocation |
– |
Default Midamble |
Table A.5.4.23: Transport channel parameters for S-CCPCH
Parameter |
FACH |
Transport Channel Number |
1 |
Transport Block Size |
240 |
Transport Block Set Size |
240 |
Transmission Time Interval |
20 ms |
Type of Error Protection |
Convolutional Coding |
Coding Rate |
½ |
Rate Matching attribute |
256 |
Size of CRC |
16 |
Table A.5.4.24: Cell specific test parameters for Cell Re-selection in CELL_FACH
Parameter |
Unit |
Cell 1 |
Cell 2 |
Cell 3 |
||||||||||||
Timeslot Number |
0 |
8 |
0 |
8 |
0 |
8 |
||||||||||
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
|||||
UTRA RF Channel Number |
Channel 1 |
Channel 2 |
Channel 1 |
|||||||||||||
PCCPCH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
|||||||||
SCH_Ec/Ior |
dB |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
|||
SCH_toffset |
0 |
0 |
0 |
0 |
5 |
5 |
5 |
5 |
10 |
10 |
10 |
10 |
||||
PICH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
|||||||||
OCNS_Ec/Ior |
dB |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
|||
|
dB |
9 |
3 |
9 |
3 |
3 |
9 |
3 |
9 |
-1 |
-1 |
-1 |
-1 |
|||
PCCPCH RSCP |
dBm |
-64 |
-70 |
-70 |
-64 |
-74 |
-74 |
|||||||||
Qoffset1s,n |
dB |
C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1,C6:0 |
C2, C1: 0; C2, C3:0; C2,C4:0 C2, C5: 0; C2, C6:0 |
C3, C1: 0; C3, C2:0; C3,C4:0 C3, C5: 0; C3, C6:0 |
||||||||||||
Qhyst1s |
dB |
0 |
0 |
0 |
||||||||||||
Treselection |
0 |
0 |
0 |
|||||||||||||
Sintrasearch |
dB |
not sent |
not sent |
not sent |
||||||||||||
Sintersearch |
dB |
not sent |
not sent |
not sent |
||||||||||||
FACH measurement occasion info |
not sent |
not sent |
not sent |
|||||||||||||
Inter-frequency TDD measurement indicator |
TRUE |
TRUE |
TRUE |
|||||||||||||
|
dBm/ 7,68 MHz |
-70 |
||||||||||||||
Propagation Condition |
AWGN |
|||||||||||||||
Cell 4 |
Cell 5 |
Cell 6 |
||||||||||||||
Timeslot |
0 |
8 |
0 |
8 |
0 |
8 |
||||||||||
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
T1 |
T2 |
|||||
UTRA RF Channel Number |
Channel 1 |
Channel 2 |
Channel 2 |
|||||||||||||
PCCPCH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
|||||||||
SCH_Ec/Ior |
dB |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
-9 |
|||
SCH_toffset |
15 |
15 |
15 |
15 |
20 |
20 |
20 |
20 |
25 |
25 |
25 |
25 |
||||
PICH_Ec/Ior |
dB |
-3 |
-3 |
-3 |
-3 |
-3 |
-3 |
|||||||||
OCNS_Ec/Ior |
dB |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
-3,12 |
|||
|
dB |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
-1 |
|||
PCCPCH RSCP |
dBm |
-74 |
-74 |
-74 |
-74 |
-74 |
-74 |
|||||||||
Qoffset1s,n |
dB |
C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0 |
C5, C1: 0; C5, C2:0; C5,C3:0 C5, C4:0; C5, C6:0 |
C6, C1: 0; C6, C2:0; C6,C3:0 C6, C4:0; C6, C5:0 |
||||||||||||
Qhyst1s |
dB |
0 |
0 |
0 |
||||||||||||
Treselection |
0 |
0 |
0 |
|||||||||||||
Sintrasearch |
dB |
not sent |
not sent |
not sent |
||||||||||||
Sintersearch |
dB |
not sent |
not sent |
not sent |
||||||||||||
FACH measurement occasion info |
not sent |
not sent |
not sent |
|||||||||||||
Inter-frequency TDD measurement indicator |
TRUE |
TRUE |
TRUE |
|||||||||||||
|
dBm/ 7,68 MHz |
-70 |
||||||||||||||
Propagation Condition |
AWGN |
NOTE: S-CCPCH shall not be located in TS0.
A.5.4.3.2.2 Test Requirements
The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send the CELL UPDATE message with cause value "cell reselection" in cell 2.
The cell re-selection delay shall be less than 3 s.
The rate of correct cell re-selections observed during repeated tests shall be at least 90%.