A.5.1 TDD/TDD Handover
25.1233GPPRelease 17Requirements for support of radio resource management (TDD)TS
A.5.1.1 3.84Mcps TDD option
A.5.1.1.1 Handover to intra-frequency cell
A.5.1.1.1.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the intra-frequency handover delay in CELL_DCH state in the single carrier case reported in section 5.1.2.1.
The test parameters are given in Table A.5.1.1 and A.5.1.2 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1G shall be used, and that P-CCPCH RSCP and SFN-CFN observed timed difference shall be reported together with Event 1G. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time "now" with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 1G. The starting point of T3 is definied as the end of the last TTI containing the physical channel reconfiguration message.
The second Beacon timeslot shall be provided in timeslot 8 for both cell 1 and cell 2. The UL DPCH shall be transmitted in timeslot 12.
Table A.5.1.1: General test parameters for Handover to intra-frequency cell
|
Parameter |
Unit |
Value |
Comment |
|
|
DCH parameters |
DL and UL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.102 section A.2.2 and A.2.1 |
||
|
Power Control |
On |
|||
|
Target quality value on DTCH |
BLER |
0.01 |
||
|
Initial conditions |
Active cell |
Cell 1 |
||
|
Neighbour cell |
Cell 2 |
|||
|
Final condition |
Active cell |
Cell 2 |
||
|
HCS |
Not used |
|||
|
O |
dB |
0 |
Cell individual offset. This value shall be used for all cells in the test. |
|
|
Hysteresis |
dB |
0 |
||
|
Time to Trigger |
ms |
0 |
||
|
Filter coefficient |
0 |
|||
|
Monitored cell list size |
6 TDD neighbours on Channel 1 |
|||
|
T1 |
s |
10 |
||
|
T2 |
s |
10 |
||
|
T3 |
s |
10 |
||
Table A.5.1.2: Cell specific test parameters for Handover to intra-frequency cell
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
||||||||||
|
DL timeslot number |
0 |
4 |
0 |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||
|
UTRA RF Channel Number |
Channel 1 |
Channel 1 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
-3 |
n.a. |
||||||||
|
SCH_Ec/Ior |
dB |
-9 |
n.a. |
-9 |
n.a. |
||||||||
|
SCH_toffset |
dB |
0 |
n.a. |
5 |
n.a. |
||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
Note 1 |
n.a. |
n.a. |
n.a. |
Note 1 |
||||||
|
OCNS_Ec/Ior |
dB |
-3,12 |
Note 2 |
n.a. |
n.a. |
-3,12 |
n.a. |
Note 2 |
|||||
|
|
dB |
1 |
-Inf. |
3 |
-Inf. |
3 |
|||||||
|
PCCPCH RSCP |
dBm |
-72 |
n.a. |
-Inf. |
-70 |
n.a. |
|||||||
|
|
dBm/3,84 MHz |
-70 |
|||||||||||
|
Propagation Condition |
AWGN |
||||||||||||
|
Note 1: The DPCH level is controlled by the power control loop Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . |
|||||||||||||
A.5.1.1.1.2 Test Requirements
The UE shall start to transmit the UL DPCH to Cell 2 less than 160 ms from the beginning of time period T3.
The rate of correct handovers observed during repeated tests shall be at least 90%.
A.5.1.1.2 Handover to inter-frequency cell
A.5.1.1.2.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the inter-frequency handover delay in CELL_DCH state in the dual carrier case reported in section 5.1.2.1.
The test consists of two successive time periods, with a time duration T1 and T2. The test parameters are given in tables A.5.1.3 and A.5.1.4 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used. The PCCPCH RSCP and SFN-CFN observed time difference of the best cell on the unused frequency shall be reported together with Event 2C reporting. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time "now" with one active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 2C. The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
The second Beacon timeslot shall be provided in timeslot 8 for cell 1 and in timeslot 10 for cell 2. The UL DPCH shall be transmitted in timeslot 12.
Table A.5.1.3: General test parameters for Handover to inter-frequency cell
|
Parameter |
Unit |
Value |
Comment |
|
|
DCH parameters |
DL and UL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.102 section A.2.2 and A.2.1 |
||
|
Power Control |
On |
|||
|
Target quality value on DTCH |
BLER |
0.01 |
||
|
Initial conditions |
Active cell |
Cell 1 |
||
|
Neighbour cell |
Cell 2 |
|||
|
Final condition |
Active cell |
Cell 2 |
||
|
HCS |
Not used |
|||
|
O |
dB |
0 |
Cell individual offset. This value shall be used for all cells in the test. |
|
|
Hysteresis |
dB |
0 |
Hysteresis parameter for event 2C |
|
|
Time to Trigger |
ms |
0 |
||
|
Threshold non-used frequency |
dBm |
-80 |
Applicable for Event 2C |
|
|
Filter coefficient |
0 |
|||
|
Monitored cell list size |
6 TDD neighbours on Channel 1 6 TDD neighbours on Channel 2 |
|||
|
TSI |
s |
1.28 |
The value shall be used for all cells in the test. |
|
|
T1 |
s |
10 |
||
|
T2 |
s |
10 |
||
|
T3 |
s |
10 |
||
TableA.5.1.4: Cell Specific parameters for Handover to inter-frequency cell
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
||||||||||
|
DL timeslot number |
0 |
4 |
2 |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||
|
UTRA RF Channel Number |
Channel 1 |
Channel 2 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
-3 |
n.a. |
||||||||
|
SCH_Ec/Ior |
dB |
-9 |
n.a. |
-9 |
n.a. |
||||||||
|
SCH_toffset |
dB |
0 |
n.a. |
5 |
n.a. |
||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
Note 1 |
n.a. |
n.a. |
n.a. |
Note 1 |
||||||
|
OCNS_Ec/Ior |
dB |
-3,12 |
Note 2 |
n.a. |
n.a. |
-3,12 |
n.a. |
Note 2 |
|||||
|
|
dB |
1 |
-Inf. |
7 |
-Inf. |
7 |
|||||||
|
PCCPCH RSCP |
dBm |
-72 |
n.a. |
-Inf. |
-66 |
n.a. |
|||||||
|
|
dBm/ 3,84 MHz |
-70 |
|||||||||||
|
Propagation Condition |
AWGN |
||||||||||||
|
Note 1: The DPCH level is controlled by the power control loop Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . |
|||||||||||||
A.5.1.1.2.2 Test Requirements
The UE shall start to transmit the UL DPCH to Cell 2 less than 160 ms from the beginning of time period T2.
The rate of correct handovers observed during repeated tests shall be at least 90%.
A.5.1.2 1.28Mcps TDD option
A.5.1.2.1 Handover to intra-frequency cell
A.5.1.2.1.1 Scenario 1
This test case is applicable for UE handovers in single frequency network and UE handovers from primary frequency to primary frequency in multi-frequency network.
A.5.1.2.1.1.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the intra-frequency handover delay in CELL_DCH state in the case as reported in section 5.1.2.1.2.
The test parameters are given in Table A.5.1.5 and A.5.1.6 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1G shall be used, and that PCCPCH RSCP and SFN-CFN observed timed difference shall be reported together with Event 1G. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration with activation time "now" at the beginning of T3 with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 1G. The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
Table A.5.1.5: General test parameters for intra-frequency handover
|
Parameter |
Unit |
Value |
Comment |
|
|
DPCH parameters |
DL and UL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.102 section A.2.2.2 and A.2.1.2 |
||
|
Power Control |
On |
|||
|
Target quality value on DPCH |
BLER |
0.01 |
||
|
Initial conditions |
Active cell |
Cell 1 |
In the case of multi-frequency network, the UE has a RRC connection on the primary frequency in cell 1. |
|
|
Neighbouring cell |
Cell 2 |
|||
|
Final condition |
Active cell |
Cell 2 |
In the case of multifrequency network, UE will handover to the primary frequency in cell 2. |
|
|
O |
dB |
0 |
cell-individual-offset The value shall be used for all cells in the test. |
|
|
Hysteresis |
dB |
0 |
||
|
Time to Trigger |
ms |
0 |
||
|
Filter coefficient |
0 |
|||
|
Monitored cell list size |
6 TDD neighbours on Channel 1 |
|||
|
T1 |
s |
5 |
||
|
T2 |
s |
5 |
||
|
T3 |
s |
5 |
||
Table A.5.1.6: Cell specific test parameters for intra-frequency handover
|
Parameter |
Unit |
Cell 1 |
||||||||||
|
Timeslot Number |
0 |
DwPTS |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||||
|
UTRA RF Channel Number(Note3) |
Channel 1 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
|||||||||
|
DwPCH_Ec/Ior |
0 |
|||||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
n.a. |
Note1 |
n.a. |
|||||||
|
OCNS_Ec/Ior |
dB |
-3 |
Note2 |
|||||||||
|
|
dB |
3 |
3 |
3 |
||||||||
|
|
dBm/1.28 MHz |
-70 |
||||||||||
|
PCCPCH_RSCP |
dBm |
-70 |
n.a. |
n.a. |
||||||||
|
Propagation Condition |
AWGN |
|||||||||||
|
Parameter |
Unit |
Cell 2 |
||||||||||
|
Timeslot Number |
0 |
DwPTS |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||||
|
UTRA RF Channel Number(Note3) |
Channel 1 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
|||||||||
|
DwPCH_Ec/Ior |
0 |
|||||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
n.a. |
n.a. |
Note1 |
|||||||
|
OCNS_Ec/Ior |
dB |
-3 |
Note2 |
|||||||||
|
|
dB |
-Inf. |
6 |
-Inf. |
6 |
-Inf. |
6 |
|||||
|
|
dBm/1.28 MHz |
-70 |
||||||||||
|
PCCPCH_RSCP |
dBm |
-Inf. |
-67 |
n.a. |
n.a. |
|||||||
|
Propagation Condition |
AWGN |
|||||||||||
|
Note 1: The DPCH level is controlled by the power control loop Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . Note 3: In the case of multi-frequency network, the UTRA RF Channel Number is the primary frequency’s channel number. |
||||||||||||
A.5.1.2.1.1.2 Test Requirements
The UE shall start to transmit the UL DPCH to cell 2 less than 160 ms from the beginning of time period T3.
The rate of correct handovers observed during repeated tests shall be at least 90%.
A.5.1.2.1.2 Scenario 2
This test case is applicable for UE handovers from secondarhy frequency to parimary frequency in the case of multi-frequency network.
A.5.1.2.1.2.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the intra-frequency handover delay in CELL_DCH state in the case as reported in section 5.1.2.1.2.
The test parameters are given in Table A.5.1.5A and A.5.1.6A below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1G shall be used, and that PCCPCH RSCP and SFN-CFN observed timed difference shall be reported together with Event 1G. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration with activation time "now" at the beginning of T3 with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 1G. The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
Table A.5.1.5A: General test parameters for intra-frequency handover
|
Parameter |
Unit |
Value |
Comment |
|
|
DPCH parameters |
DL and UL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.102 section A.2.2.2 and A.2.1.2 |
||
|
Power Control |
On |
|||
|
Target quality value on DPCH |
BLER |
0.01 |
||
|
Initial conditions |
Active cell |
Cell 1 |
The UE has a RRC connection on the secondary frequency in cell 1. |
|
|
Neighbouring cell |
Cell 2 |
|||
|
Final condition |
Active cell |
Cell 2 |
The UE will handover to the primary frequency in cell 2. |
|
|
O |
dB |
0 |
cell-individual-offset The value shall be used for all cells in the test. |
|
|
Hysteresis |
dB |
0 |
||
|
Time to Trigger |
ms |
0 |
||
|
Filter coefficient |
0 |
|||
|
Monitored cell list size |
6 TDD neighbours on Channel 1 |
|||
|
T1 |
s |
5 |
||
|
T2 |
s |
5 |
||
|
T3 |
s |
5 |
||
Table A.5.1.6A: Cell specific test parameters for intra-frequency handover
|
Parameter |
Unit |
Cell 1 |
||||||||||
|
Timeslot Number |
0 |
DwPTS |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||||
|
UTRA RF Channel Number(Note3) |
Channel 1 |
|||||||||||
|
UTRA RF Channel Number(Note4) |
Channel 2 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
|||||||||
|
DwPCH_Ec/Ior |
0 |
|||||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
n.a. |
Note1 |
n.a. |
|||||||
|
OCNS_Ec/Ior |
dB |
-3 |
Note2 |
|||||||||
|
|
dB |
3 |
3 |
3 |
||||||||
|
|
dBm/1.28 MHz |
-70 |
||||||||||
|
PCCPCH_RSCP |
dBm |
-70 |
n.a. |
n.a. |
||||||||
|
Propagation Condition |
AWGN |
|||||||||||
|
Parameter |
Unit |
Cell 2 |
||||||||||
|
Timeslot Number |
0 |
DwPTS |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||||
|
UTRA RF Channel Number(Note3) |
Channel 2 |
|||||||||||
|
UTRA RF Channel Number(Note4) |
Channel 1 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
|||||||||
|
DwPCH_Ec/Ior |
0 |
|||||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
n.a. |
n.a. |
Note1 |
|||||||
|
OCNS_Ec/Ior |
dB |
-3 |
Note2 |
|||||||||
|
|
dB |
-Inf. |
6 |
-Inf. |
6 |
-Inf. |
6 |
|||||
|
|
dBm/1.28 MHz |
-70 |
||||||||||
|
PCCPCH_RSCP |
dBm |
-Inf. |
-67 |
n.a. |
n.a. |
|||||||
|
Propagation Condition |
AWGN |
|||||||||||
|
Note 1: The DPCH level is controlled by the power control loop Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . Note3: The UTRA RF Channel Number is the primary frequency’s channel number. Note3: The UTRA RF Channel Number is the secondary frequency’s channel number. |
||||||||||||
A.5.1.2.1.2.2 Test Requirements
The UE shall start to transmit the UL DPCH in cell 2 less than 160 ms from the beginning of time period T3.
The rate of correct handovers observed during repeated tests shall be at least 90%.
A.5.1.2.2 Handover to inter-frequency cell
A.5.1.2.2.1 Scenario 1
This test case is applicable for UE handovers in single frequency network and UE handovers from primary frequency to the primary frequency in multi-frequency network.
A.5.1.2.2.1.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the inter-frequency handover delay in CELL_DCH in the case as reported in section 5.1.2.1.2.
The test consists of three successive time periods, with a time duration T1, T2 and T3. The test parameters are given in tables A.5.1.7 and A.5.1.8 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used. The PCCPCH RSCP and SFN-CFN observed timed difference of the best cell on the unused frequency shall be reported together with Event 2C reporting. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration with activation time "now" with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 2C. The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
Table A.5.1.7: General test parameters for inter-frequency handover
|
Parameter |
Unit |
Value |
Comment |
|
|
DPCH parameters |
DL and UL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.102 section A.2.2.2 and A.2.1.2 |
||
|
Power Control |
On |
|||
|
Target quality value on DPCH |
BLER |
0.01 |
||
|
Initial conditions |
Active cell |
Cell 1 |
In the case of multi-frequency network, the UE has a RRC connection on the primary frequency in cell 1. |
|
|
Neighbour cell |
Cell 2 |
|||
|
Final conditions |
Active cell |
Cell 2 |
In the case of multi-frequency network, the UE will handover to the primary frequency in cell 2. |
|
|
Threshold non used frequency |
dBm |
-75 |
Absolute RSCP threshold for event 2C |
|
|
O |
dB |
0 |
cell-individual-offset The value shall be used for all cells in the test. |
|
|
Hysteresis |
dB |
0 |
||
|
Time to Trigger |
ms |
0 |
||
|
Filter coefficient |
0 |
|||
|
Monitored cell list size |
6 TDD neighbours on Channel 1 6 TDD neighbours on Channel 2 |
|||
|
T1 |
s |
5 |
||
|
T2 |
s |
10 |
||
|
T3 |
s |
5 |
||
TableA.5.1.8: Cell Specific parameters for inter-frequency handover
|
Parameter |
Unit |
Cell 1 |
||||||||||
|
Timeslot Number |
0 |
DwPTS |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||||
|
UTRA RF Channel Number(Note 3) |
Channel 1 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
|||||||||
|
DwPCH_Ec/Ior |
0 |
|||||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
n.a. |
Note1 |
n.a. |
|||||||
|
OCNS_Ec/Ior |
dB |
-3 |
Note2 |
|||||||||
|
|
dB |
3 |
3 |
3 |
||||||||
|
|
dBm/1.28 MHz |
-70 |
||||||||||
|
PCCPCH_RSCP |
dBm |
-70 |
n.a. |
n.a. |
||||||||
|
Propagation Condition |
AWGN |
|||||||||||
|
Parameter |
Unit |
Cell 2 |
||||||||||
|
Timeslot Number |
0 |
DwPTS |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||||
|
UTRA RF Channel Number(Note 3) |
Channel 2 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
|||||||||
|
DwPCH_Ec/Ior |
0 |
|||||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
n.a. |
n.a. |
Note1 |
|||||||
|
OCNS_Ec/Ior |
dB |
-3 |
Note2 |
|||||||||
|
|
dB |
-Inf. |
4 |
-Inf. |
4 |
-Inf. |
4 |
|||||
|
|
dBm/1.28 MHz |
-70 |
||||||||||
|
PCCPCH_RSCP |
dBm |
-Inf. |
-69 |
n.a. |
n.a. |
|||||||
|
Propagation Condition |
AWGN |
|||||||||||
|
Note 1: The DPCH level is controlled by the power control loop Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . Note 3: In the case of multi-frequency network, the UTRA RF Channel Number is the primary frequency’s channel number. |
||||||||||||
A.5.1.2.2.1.2 Test Requirements
The UE shall start to transmit the UL DPCH to cell 2 less than 160 ms from the beginning of time period T3.
The rate of correct handovers observed during repeated tests shall be at least 90%.
A.5.1.2.2.2 Scenario 2
This test case is applicable for UE handovers from secondarhy frequency to parimary frequency in the case of multi-frequency network.
A.5.1.2.2.2.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the inter-frequency handover delay in CELL_DCH in the case as reported in section 5.1.2.1.2.
The test consists of three successive time periods, with a time duration T1, T2 and T3. The test parameters are given in tables A.5.1.7A and A.5.1.8A below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used. The PCCPCH RSCP and SFN-CFN observed timed difference of the best cell on the unused frequency shall be reported together with Event 2C reporting. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration with activation time "now" with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 2C. The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
Table A.5.1.7: General test parameters for inter-frequency handover
|
Parameter |
Unit |
Value |
Comment |
|
|
DPCH parameters |
DL and UL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.102 section A.2.2.2 and A.2.1.2 |
||
|
Power Control |
On |
|||
|
Target quality value on DPCH |
BLER |
0.01 |
||
|
Initial conditions |
Active cell |
Cell 1 |
The UE has a RRC connection on the secondary frequency in cell 1. |
|
|
Neighbour cell |
Cell 2 |
|||
|
Final conditions |
Active cell |
Cell 2 |
The UE will handover to the primary frequency in cell 2. |
|
|
Threshold non used frequency |
dBm |
-75 |
Absolute RSCP threshold for event 2C |
|
|
O |
dB |
0 |
cell-individual-offset The value shall be used for all cells in the test. |
|
|
Hysteresis |
dB |
0 |
||
|
Time to Trigger |
ms |
0 |
||
|
Filter coefficient |
0 |
|||
|
Monitored cell list size |
6 TDD neighbours on Channel 1 6 TDD neighbours on Channel 2 |
|||
|
T1 |
s |
5 |
||
|
T2 |
s |
10 |
||
|
T3 |
s |
5 |
||
TableA.5.1.8: Cell Specific parameters for inter-frequency handover
|
Parameter |
Unit |
Cell 1 |
||||||||||
|
Timeslot Number |
0 |
DwPTS |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||||
|
UTRA RF Channel Number(Note 3) |
Channel 1 |
|||||||||||
|
UTRA RF Channel Number(Note 4) |
Channel 2 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
|||||||||
|
DwPCH_Ec/Ior |
0 |
|||||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
n.a. |
Note1 |
n.a. |
|||||||
|
OCNS_Ec/Ior |
dB |
-3 |
Note2 |
|||||||||
|
|
dB |
3 |
3 |
3 |
||||||||
|
|
dBm/1.28 MHz |
-70 |
||||||||||
|
PCCPCH_RSCP |
dBm |
-70 |
n.a. |
n.a. |
||||||||
|
Propagation Condition |
AWGN |
|||||||||||
|
Parameter |
Unit |
Cell 2 |
||||||||||
|
Timeslot Number |
0 |
DwPTS |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||||
|
UTRA RF Channel Number(Note 3) |
Channel 1 |
|||||||||||
|
UTRA RF Channel Number(Note 4) |
Channel 2 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
|||||||||
|
DwPCH_Ec/Ior |
0 |
|||||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
n.a. |
n.a. |
Note1 |
|||||||
|
OCNS_Ec/Ior |
dB |
-3 |
Note2 |
|||||||||
|
|
dB |
-Inf. |
4 |
-Inf. |
4 |
-Inf. |
4 |
|||||
|
|
dBm/1.28 MHz |
-70 |
||||||||||
|
PCCPCH_RSCP |
dBm |
-Inf. |
-69 |
n.a. |
n.a. |
|||||||
|
Propagation Condition |
AWGN |
|||||||||||
|
Note 1: The DPCH level is controlled by the power control loop Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . Note3: The UTRA RF Channel Number is the primary frequency’s channel number. Note4: The UTRA RF Channel Number is the secondary frequency’s channel number. |
||||||||||||
A.5.1.2.2.2.2 Test Requirements
The UE shall start to transmit the UL DPCH to cell 2 less than 160 ms from the beginning of time period T3.
The rate of correct handovers observed during repeated tests shall be at least 90%.
A.5.1.2.3 Handover to inter-band cell
A.5.1.2.3.1 Scenario 1
This test case is applicable for UE handovers from primary frequency to the primary frequency in multi-band frequency network.
A.5.1.2.3.1.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the inter-band handover delay in CELL_DCH in the case as reported in section 5.1.2.1.2.
The test consists of three successive time periods, with a time duration T1, T2 and T3. The test parameters are given in tables A.5.1.8A and A.5.1.8B below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used. The PCCPCH RSCP and SFN-CFN observed timed difference of the best cell on the unused frequency shall be reported together with Event 2C reporting. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration with activation time "now" with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 2C. The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
Table A.5.1.8A: General test parameters for inter-band handover
|
Parameter |
Unit |
Value |
Comment |
|
|
DPCH parameters |
DL and UL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.102 section A.2.2.2 and A.2.1.2 |
||
|
Power Control |
On |
|||
|
Target quality value on DPCH |
BLER |
0.01 |
||
|
Initial conditions |
Active cell |
Cell 1 |
In the case of multi-frequency network, the UE has a RRC connection on the primary frequency in cell 1. |
|
|
Neighbour cell |
Cell 2 |
|||
|
Final conditions |
Active cell |
Cell 2 |
In the case of multi-frequency network, the UE will handover to the primary frequency in cell 2. |
|
|
Threshold non used frequency |
dBm |
-75 |
Absolute RSCP threshold for event 2C |
|
|
O |
dB |
0 |
cell-individual-offset The value shall be used for all cells in the test. |
|
|
Hysteresis |
dB |
0 |
||
|
Time to Trigger |
ms |
0 |
||
|
Filter coefficient |
0 |
|||
|
Monitored cell list size |
6 TDD neighbours on Channel 1 6 TDD neighbours on Channel 2 |
|||
|
T1 |
s |
5 |
||
|
T2 |
s |
10 |
||
|
T3 |
s |
5 |
||
TableA.5.1.8B: Cell Specific parameters for inter-band handover
|
Parameter |
Unit |
Cell 1 |
||||||||||
|
Timeslot Number |
0 |
DwPTS |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||||
|
UTRA RF Channel Number(Note 3) |
Channel 1 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
|||||||||
|
DwPCH_Ec/Ior |
0 |
|||||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
n.a. |
Note1 |
n.a. |
|||||||
|
OCNS_Ec/Ior |
dB |
-3 |
Note2 |
|||||||||
|
|
dB |
3 |
3 |
3 |
||||||||
|
|
dBm/1.28 MHz |
-70 |
||||||||||
|
PCCPCH_RSCP |
dBm |
-70 |
n.a. |
n.a. |
||||||||
|
Propagation Condition |
AWGN |
|||||||||||
|
Parameter |
Unit |
Cell 2 |
||||||||||
|
Timeslot Number |
0 |
DwPTS |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||||
|
UTRA RF Channel Number(Note 3) |
Channel 2 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
|||||||||
|
DwPCH_Ec/Ior |
0 |
|||||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
n.a. |
n.a. |
Note1 |
|||||||
|
OCNS_Ec/Ior |
dB |
-3 |
Note2 |
|||||||||
|
|
dB |
-Inf. |
4 |
-Inf. |
4 |
-Inf. |
4 |
|||||
|
|
dBm/1.28 MHz |
-70 |
||||||||||
|
PCCPCH_RSCP |
dBm |
-Inf. |
-69 |
n.a. |
n.a. |
|||||||
|
Propagation Condition |
AWGN |
|||||||||||
|
Note 1: The DPCH level is controlled by the power control loop Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . Note 3: In the case of multi-frequency network, the UTRA RF Channel Number is the primary frequency’s channel number. |
||||||||||||
A.5.1.2.3.1.2 Test Requirements
The UE shall start to transmit the UL DPCH to cell 2 less than 160 ms from the beginning of time period T3.
The rate of correct handovers observed during repeated tests shall be at least 90%.
A.5.1.2.3.2 Scenario 2
This test case is applicable for UE handovers from primary frequency to secondary frequency in multi-band network.
A.5.1.2.3.2.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the inter-frequency handover delay in CELL_DCH in the case as reported in section 5.1.2.1.2.
In cell 1, the primary frequency uses frequency b of band a, and the secondary frequency uses frequencies a and c of band a. In cell 2, the primary frequency uses frequency e of band a, and the secondary frequency uses frequencies d and f of band f.
The test consists of three successive time periods, with a time duration T1, T2 and T3. The test parameters are given in tables A.5.1.8C and A.5.1.8D below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used. The PCCPCH RSCP and SFN-CFN observed timed difference of the best cell on the unused frequency shall be reported together with Event 2C reporting. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration with activation time "now" with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 2C. The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
Table A.5.1.8C: General test parameters for inter-band handover
|
Parameter |
Unit |
Value |
Comment |
|
|
DPCH parameters |
DL and UL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.102 section A.2.2.2 and A.2.1.2 |
||
|
Power Control |
On |
|||
|
Target quality value on DPCH |
BLER |
0.01 |
||
|
Initial conditions |
Active cell |
Cell 1 |
In the case of multi-frequency network, the UE has a RRC connection on the primary frequency in cell 1. |
|
|
Neighbour cell |
Cell 2 |
|||
|
Final conditions |
Active cell |
Cell 2 |
In the case of multi-frequency network, the UE will handover to the primary frequency in cell 2. |
|
|
Threshold non used frequency |
dBm |
-75 |
Absolute RSCP threshold for event 2C |
|
|
O |
dB |
0 |
cell-individual-offset The value shall be used for all cells in the test. |
|
|
Hysteresis |
dB |
0 |
||
|
Time to Trigger |
ms |
0 |
||
|
Filter coefficient |
0 |
|||
|
Monitored cell list size |
6 TDD neighbours on Channel 1 6 TDD neighbours on Channel 2 |
|||
|
T1 |
s |
5 |
||
|
T2 |
s |
10 |
||
|
T3 |
s |
5 |
||
Table A.5.1.8D: Cell Specific parameters for inter-band handover
|
Parameter |
Unit |
Cell 1 |
||||||||||
|
Timeslot Number |
0 |
DwPTS |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||||
|
UTRA RF Channel Number(Note 3) |
Channel 1 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
|||||||||
|
DwPCH_Ec/Ior |
0 |
|||||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
n.a. |
Note1 |
n.a. |
|||||||
|
OCNS_Ec/Ior |
dB |
-3 |
Note2 |
|||||||||
|
|
dB |
3 |
3 |
3 |
||||||||
|
|
dBm/1.28 MHz |
-70 |
||||||||||
|
PCCPCH_RSCP |
dBm |
-70 |
n.a. |
n.a. |
||||||||
|
Propagation Condition |
AWGN |
|||||||||||
|
Parameter |
Unit |
Cell 2 |
||||||||||
|
Timeslot Number |
0 |
DwPTS |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||||
|
UTRA RF Channel Number(Note 3) |
Channel 2 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
|||||||||
|
DwPCH_Ec/Ior |
0 |
|||||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
n.a. |
n.a. |
Note1 |
|||||||
|
OCNS_Ec/Ior |
dB |
-3 |
Note2 |
|||||||||
|
|
dB |
-Inf. |
4 |
-Inf. |
4 |
-Inf. |
4 |
|||||
|
|
dBm/1.28 MHz |
-70 |
||||||||||
|
PCCPCH_RSCP |
dBm |
-Inf. |
-69 |
n.a. |
n.a. |
|||||||
|
Propagation Condition |
AWGN |
|||||||||||
|
Note 1: The DPCH level is controlled by the power control loop Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . Note 3: In the case of multi-frequency network, the UTRA RF Channel Number is the primary frequency’s channel number. |
||||||||||||
A.5.1.2.3.2.2 Test Requirements
The UE shall start to transmit the UL DPCH to cell 2 less than 160 ms from the beginning of time period T3.
The rate of correct handovers observed during repeated tests shall be at least 90%.
A.5.1.2.3.3 Scenario 3
This test case is applicable for UE handovers from secondary frequency to secondary frequency in multi-band network.
A.5.1.2.3.3.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the inter-frequency handover delay in CELL_DCH in the case as reported in section 5.1.2.1.2.
In cell 1, the primary frequency uses frequency e of band a, and the secondary frequency uses frequencies d and f of band f. In cell 2, the primary frequency uses frequency b of band a, and the secondary frequency uses frequencies a and c of band a.
The test consists of three successive time periods, with a time duration T1, T2 and T3. The test parameters are given in tables A.5.1.8E and A.5.1.8F below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used. The PCCPCH RSCP and SFN-CFN observed timed difference of the best cell on the unused frequency shall be reported together with Event 2C reporting. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration with activation time "now" with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 2C. The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
Table A.5.1.8E: General test parameters for inter-band handover
|
Parameter |
Unit |
Value |
Comment |
|
|
DPCH parameters |
DL and UL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.102 section A.2.2.2 and A.2.1.2 |
||
|
Power Control |
On |
|||
|
Target quality value on DPCH |
BLER |
0.01 |
||
|
Initial conditions |
Active cell |
Cell 1 |
In the case of multi-frequency network, the UE has a RRC connection on the primary frequency in cell 1. |
|
|
Neighbour cell |
Cell 2 |
|||
|
Final conditions |
Active cell |
Cell 2 |
In the case of multi-frequency network, the UE will handover to the secondary frequency in cell 2. |
|
|
Threshold non used frequency |
dBm |
-75 |
Absolute RSCP threshold for event 2C |
|
|
O |
dB |
0 |
cell-individual-offset The value shall be used for all cells in the test. |
|
|
Hysteresis |
dB |
0 |
||
|
Time to Trigger |
ms |
0 |
||
|
Filter coefficient |
0 |
|||
|
Monitored cell list size |
6 TDD neighbours on Channel 1 6 TDD neighbours on Channel 2 |
|||
|
T1 |
s |
5 |
||
|
T2 |
s |
10 |
||
|
T3 |
s |
5 |
||
Table A.5.1.8F: Cell Specific parameters for inter-band handover
|
Parameter |
Unit |
Cell 1 |
||||||||||
|
Timeslot Number |
0 |
DwPTS |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||||
|
UTRA RF Channel Number(Note 3) |
Channel 1 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
|||||||||
|
DwPCH_Ec/Ior |
0 |
|||||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
n.a. |
Note1 |
n.a. |
|||||||
|
OCNS_Ec/Ior |
dB |
-3 |
Note2 |
|||||||||
|
|
dB |
3 |
3 |
3 |
||||||||
|
|
dBm/1.28 MHz |
-70 |
||||||||||
|
PCCPCH_RSCP |
dBm |
-70 |
n.a. |
n.a. |
||||||||
|
Propagation Condition |
AWGN |
|||||||||||
|
Parameter |
Unit |
Cell 2 |
||||||||||
|
Timeslot Number |
0 |
DwPTS |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||||
|
UTRA RF Channel Number(Note 3) |
Channel 2 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
|||||||||
|
DwPCH_Ec/Ior |
0 |
|||||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
n.a. |
n.a. |
Note1 |
|||||||
|
OCNS_Ec/Ior |
dB |
-3 |
Note2 |
|||||||||
|
|
dB |
-Inf. |
4 |
-Inf. |
4 |
-Inf. |
4 |
|||||
|
|
dBm/1.28 MHz |
-70 |
||||||||||
|
PCCPCH_RSCP |
dBm |
-Inf. |
-69 |
n.a. |
n.a. |
|||||||
|
Propagation Condition |
AWGN |
|||||||||||
|
Note 1: The DPCH level is controlled by the power control loop Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . Note 3: In the case of multi-frequency network, the UTRA RF Channel Number is the primary frequency’s channel number. |
||||||||||||
A.5.1.2.3.3.2 Test Requirements
The UE shall start to transmit the UL DPCH to cell 2 less than 160 ms from the beginning of time period T3.
The rate of correct handovers observed during repeated tests shall be at least 90%.
A.5.1.3 7.68Mcps TDD option
A.5.1.3.1 Handover to intra-frequency cell
A.5.1.3.1.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the intra-frequency handover delay in CELL_DCH state in the single carrier case reported in section 5.1.2.1.
The test parameters are given in Table A.5.1.9 and A.5.1.10 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 1G shall be used, and that P-CCPCH RSCP and SFN-CFN observed timed difference shall be reported together with Event 1G. The test consists of three successive time periods, with a time duration of T1, T2 and T3 respectively. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time "now" with a new active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 1G. The starting point of T3 is definied as the end of the last TTI containing the physical channel reconfiguration message.
The second Beacon timeslot shall be provided in timeslot 8 for both cell 1 and cell 2. The UL DPCH shall be transmitted in timeslot 12.
Table A.5.1.9: General test parameters for Handover to intra-frequency cell
|
Parameter |
Unit |
Value |
Comment |
|
|
DCH parameters |
DL and UL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.102 section A.2.2 and A.2.1 |
||
|
Power Control |
On |
|||
|
Target quality value on DTCH |
BLER |
0.01 |
||
|
Initial conditions |
Active cell |
Cell 1 |
||
|
Neighbour cell |
Cell 2 |
|||
|
Final condition |
Active cell |
Cell 2 |
||
|
HCS |
Not used |
|||
|
O |
dB |
0 |
Cell individual offset. This value shall be used for all cells in the test. |
|
|
Hysteresis |
dB |
0 |
||
|
Time to Trigger |
ms |
0 |
||
|
Filter coefficient |
0 |
|||
|
Monitored cell list size |
6 TDD neighbours on Channel 1 |
|||
|
T1 |
s |
10 |
||
|
T2 |
s |
10 |
||
|
T3 |
s |
10 |
||
Table A.5.1.10: Cell specific test parameters for Handover to intra-frequency cell
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
||||||||||
|
DL timeslot number |
0 |
4 |
0 |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||
|
UTRA RF Channel Number |
Channel 1 |
Channel 1 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
-3 |
n.a. |
||||||||
|
SCH_Ec/Ior |
dB |
-9 |
n.a. |
-9 |
n.a. |
||||||||
|
SCH_toffset |
dB |
0 |
n.a. |
5 |
n.a. |
||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
Note 1 |
n.a. |
n.a. |
n.a. |
Note 1 |
||||||
|
OCNS_Ec/Ior |
dB |
-3,12 |
Note 2 |
n.a. |
n.a. |
-3,12 |
n.a. |
Note 2 |
|||||
|
|
dB |
1 |
-Inf. |
3 |
-Inf. |
3 |
|||||||
|
PCCPCH RSCP |
dBm |
-72 |
n.a. |
-Inf. |
-70 |
n.a. |
|||||||
|
|
dBm/7,68 MHz |
-70 |
|||||||||||
|
Propagation Condition |
AWGN |
||||||||||||
|
Note 1: The DPCH level is controlled by the power control loop Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . |
|||||||||||||
A.5.1.3.1.2 Test Requirements
The UE shall start to transmit the UL DPCH to Cell 2 less than 160 ms from the beginning of time period T3.
The rate of correct handovers observed during repeated tests shall be at least 90%.
A.5.1.3.2 Handover to inter-frequency cell
A.5.1.3.2.1 Test Purpose and Environment
The purpose of this test is to verify the requirement for the inter-frequency handover delay in CELL_DCH state in the dual carrier case reported in section 5.1.2.1.
The test consists of two successive time periods, with a time duration T1 and T2. The test parameters are given in tables A.5.1.11 and A.5.1.12 below. In the measurement control information it is indicated to the UE that event-triggered reporting with Event 2C shall be used. The PCCPCH RSCP and SFN-CFN observed time difference of the best cell on the unused frequency shall be reported together with Event 2C reporting. At the start of time duration T1, the UE may not have any timing information of cell 2.
UTRAN shall send a Physical Channel reconfiguration message with activation time "now" with one active cell, cell 2. The Physical Channel reconfiguration message shall be sent to the UE during period T2, after the UE has reported event 2C. The starting point of T3 is defined as the end of the last TTI containing the physical channel reconfiguration message.
The second Beacon timeslot shall be provided in timeslot 8 for cell 1 and in timeslot 10 for cell 2. The UL DPCH shall be transmitted in timeslot 12.
Table A.5.1.11: General test parameters for Handover to inter-frequency cell
|
Parameter |
Unit |
Value |
Comment |
|
|
DCH parameters |
DL and UL Reference Measurement Channel 12.2 kbps |
As specified in TS 25.102 section A.2.2 and A.2.1 |
||
|
Power Control |
On |
|||
|
Target quality value on DTCH |
BLER |
0.01 |
||
|
Initial conditions |
Active cell |
Cell 1 |
||
|
Neighbour cell |
Cell 2 |
|||
|
Final condition |
Active cell |
Cell 2 |
||
|
HCS |
Not used |
|||
|
O |
dB |
0 |
Cell individual offset. This value shall be used for all cells in the test. |
|
|
Hysteresis |
dB |
0 |
Hysteresis parameter for event 2C |
|
|
Time to Trigger |
ms |
0 |
||
|
Threshold non-used frequency |
dBm |
-80 |
Applicable for Event 2C |
|
|
Filter coefficient |
0 |
|||
|
Monitored cell list size |
6 TDD neighbours on Channel 1 6 TDD neighbours on Channel 2 |
|||
|
TSI |
s |
1.28 |
The value shall be used for all cells in the test. |
|
|
T1 |
s |
10 |
||
|
T2 |
s |
10 |
||
|
T3 |
s |
10 |
||
TableA.5.1.12: Cell Specific parameters for Handover to inter-frequency cell
|
Parameter |
Unit |
Cell 1 |
Cell 2 |
||||||||||
|
DL timeslot number |
0 |
4 |
2 |
5 |
|||||||||
|
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
T1 |
T2 |
T3 |
||
|
UTRA RF Channel Number |
Channel 1 |
Channel 2 |
|||||||||||
|
PCCPCH_Ec/Ior |
dB |
-3 |
n.a. |
-3 |
n.a. |
||||||||
|
SCH_Ec/Ior |
dB |
-9 |
n.a. |
-9 |
n.a. |
||||||||
|
SCH_toffset |
dB |
0 |
n.a. |
5 |
n.a. |
||||||||
|
DPCH_Ec/Ior |
dB |
n.a. |
Note 1 |
n.a. |
n.a. |
n.a. |
Note 1 |
||||||
|
OCNS_Ec/Ior |
dB |
-3,12 |
Note 2 |
n.a. |
n.a. |
-3,12 |
n.a. |
Note 2 |
|||||
|
|
dB |
1 |
-Inf. |
7 |
-Inf. |
7 |
|||||||
|
PCCPCH RSCP |
dBm |
-72 |
n.a. |
-Inf. |
-66 |
n.a. |
|||||||
|
|
dBm/ 7,68 MHz |
-70 |
|||||||||||
|
Propagation Condition |
AWGN |
||||||||||||
|
Note 1: The DPCH level is controlled by the power control loop Note 2: The power of the OCNS channel that is added shall make the total power from the cell to be equal to Ior . |
|||||||||||||
A.5.1.3.2.2 Test Requirements
The UE shall start to transmit the UL DPCH to Cell 2 less than 160 ms from the beginning of time period T2.
The rate of correct handovers observed during repeated tests shall be at least 90%.