A.4 Idle Mode

25.1233GPPRelease 17Requirements for support of radio resource management (TDD)TS

Tools: ARFCN - Frequency Conversion for 5G NR/LTE/UMTS/GSM

A.4.1 Cell selection

NOTE: This section is included for consistency with numbering with section 4; no test covering requirements exist.

A.4.2 Cell Re-Selection

For each of the re-selection scenarios in section 4.2 a test is proposed.

For TDD/TDD cell reselection two scenarios are considered:

Scenario 1: Single carrier case

Scenario 2: Multi carrier case

A.4.2.1 Scenario 1: Cell re-selection to intra frequency TDD cell

A.4.2.1.1 Test Purpose and Environment

This test is to verify the requirement for the cell re-selection delay in the single carrier case reported in section 4.2.2.

A.4.2.1.1.1 3.84 Mcps TDD option

This scenario implies the presence of 1 carrier and 6 cells as given in Table A.4.1and A.4.2. Cell 1 and cell 2 shall belong to different Location Areas.

Table A.4.1: General test parameters for Cell Re-selection to intra-frequency TDD cell

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1
Initial condition	Neighbour cells		Cell2, Cell3,Cell4, Cell5, Cell6
Final condition	Active cell		Cell2
HCS			Not used
UE_TXPWR_MAX_RACH		dBm	21	The value shall be used for all cells in the test.
Qrxlevmin		dBm	-102	The value shall be used for all cells in the test.
Access Service Class (ASC#0) ‑ Persistence value			1	Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
T_SI		s	1.28	The value shall be used for all cells in the test.
DRX cycle length		s	1.28	The value shall be used for all cells in the test.
T1		s	15
T2		s	15

Table A.4.2: Cell re-selection to intra-frequency TDD cell

Parameter	Unit	Cell 1				Cell 2				Cell 3
Timeslot Number		0		8		0		8		0		8
		T1	T2	T1	T2	T1	T2	T1	T2	T1	T2	T1	T2
UTRA RF Channel Number		Channel 1				Channel 1				Channel 1
PCCPCH_Ec/Ior	dB	-3	-3			-3	-3			-3	-3
SCH_Ec/Ior	dB	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9
SCH_t_offset		0	0	0	0	5	5	5	5	10	10	10	10
PICH_Ec/Ior	dB			-3	-3			-3	-3			-3	-3
OCNS_Ec/Ior	dB	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12
	dB	9	7	9	7	7	9	7	9	-1	-1	-1	-1
PCCPCH RSCP	dBm	-64	-66			-66	-64			-74	-74
Qoffset1_s,n	dB	C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1,C6:0				C2, C1: 0; C2, C3:0; C2,C4:0 C2, C5: 0; C2,C6:0				C3, C1: 0; C3, C2:0; C3,C4:0 C3, C5: 0; C3,C6:0
Qhyst 1_s	dB	0				0				0
Treselection	s	0				0				0
Sintrasearch	dB	not sent				not sent				not sent
		Cell 4				Cell 5				Cell 6
Timeslot		0		8		0		8		0		8
		T1	T2	T1	T2	T1	T2	T1	T2	T1	T2	T1	T2
UTRA RF Channel Number		Channel 1				Channel 1				Channel 1
PCCPCH_Ec/Ior	dB	-3	-3			-3	-3			-3	-3
SCH_Ec/Ior	dB	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9
SCH_t_offset		15	15	15	15	20	20	20	20	25	25	25	25
PICH_Ec/Ior	dB			-3	-3			-3	-3			-3	-3
OCNS_Ec/Ior	dB	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12
	dB	-1	-1	-1	-1	-1	-1	-1	-1	-1	-1	-1	-1
PCCPCH RSCP	dBm	-74	-74			-74	-74			-74	-74
Qoffset1_s,n	dB	C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0				C5, C1: 0; C5, C2:0; C5,C3:0 C5, C4:0; C5, C6:0				C6, C1: 0; C6, C2:0; C6,C3:0 C6, C4:0; C6, C5:0
Qhyst1_s	dB	0				0				0
Treselection	s	0				0				0
Sintrasearch	dB	not sent				not sent				not sent
	dBm/3,84 MHz	-70
Propagation Condition		AWGN

A.4.2.1.1.2 1.28 Mcps TDD option

This scenario implies the presence of 1 carrier and 6 cells as given in Table A.4.1A and A.4.2A. The UE is requested to monitor neighbouring cells on 1 carrier. Cell 1 and cell 2 shall belong to different Location Areas.

Table A.4.1A: General test parameters for Cell Re-selection to intra-frequency TDD cell

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1
Initial condition	Neighbour cells		Cell2, Cell3,Cell4, Cell5, Cell6
Final condition	Active cell		Cell2
HCS			Not used
UE_TXPWR_MAX_RACH		dBm	21	The value shall be used for all cells in the test.
Qrxlevmin		dBm	-103	The value shall be used for all cells in the test.
Access Service Class (ASC#0) ‑- Persistence value			1	Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
T_SI		s	1.28	The value shall be used for all cells in the test.
DRX cycle length		s	1.28	The value shall be used for all cells in the test.
T1		s	15
T2		s	15

Table A.4.2A: Cell re-selection to intra-frequency TDD cell

Parameter	Unit	Cell 1				Cell 2				Cell 3
Timeslot Number		0		DWPTS		0		DWPTS		0			DWPTS
		T1	T2	T1	T2	T1	T2	T1	T2	T1	T2		T1	T2
UTRA RF Channel Number		Channel 1				Channel 1				Channel 1
PCCPCH_Ec/Ior	dB	-3	-3			-3	-3			-3		-3
DwPCH_Ec/Ior	dB			0	0			0	0				0	0
OCNS_Ec/Ior	dB	-3	-3			-3	-3			-3		-3
	dB	10	7	10	7	7	10	7	10	-1		-1	-1	-1
PCCPCH RSCP	dBm	-63	-66			-66	-63			-74		-74
Qoffset1_s,n	dB	C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1,C6:0				C2, C1: 0; C2, C3:0; C2,C4:0 C2, C5: 0; C2, C6:0				C3, C1: 0; C3, C2:0; C3,C4:0 C3, C5: 0; C3, C6:0
Qhyst1_s	dB	0				0				0
Treselection	s	0				0				0
Sintrasearch	dB	not sent				not sent				not sent
		Cell 4				Cell 5				Cell 6
Timeslot		0		DWPTS		0		DWPTS		0			DWPTS
		T1	T2	T1	T2	T1	T2	T1	T2	T1		T2	T1	T2
UTRA RF Channel Number		Channel 1				Channel 1				Channel 1
PCCPCH_Ec/Ior	dB	-3	-3			-3	-3			-3		-3
DwPCH_Ec/Ior	dB			0	0			0	0				0	0
OCNS_Ec/Ior	dB	-3	-3			-3	-3			-3		-3
	dB	-1	-1	-1	-1	-1	-1	-1	-1	-1		-1	-1	-1
PCCPCH RSCP	dBm	-74	-74			-74	-74			-74		-74
Qoffset1_s,n	dB	C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0				C5, C1: 0; C5, C2:0; C5,C3:0 C5, C4:0; C5, C6:0				C6, C1: 0; C6, C2:0; C6,C3:0 C6, C4:0; C6, C5:0
Qhyst1_s	dB	0				0				0
Treselection	s	0				0				0
Sintrasearch	dB	not sent				not sent				not sent
	dBm/ 1.28 MHz	-70
Propagation Condition		AWGN
Note: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number.

A.4.2.1.1.3 7.68 Mcps TDD option

This scenario implies the presence of 1 carrier and 6 cells as given in Table A.4.1B and A.4.2B. Cell 1 and cell 2 shall belong to different Location Areas.

Table A.4.1B: General test parameters for Cell Re-selection to intra-frequency TDD cell

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1
Initial condition	Neighbour cells		Cell2, Cell3,Cell4, Cell5, Cell6
Final condition	Active cell		Cell2
HCS			Not used
UE_TXPWR_MAX_RACH		dBm	21	The value shall be used for all cells in the test.
Qrxlevmin		dBm	-102	The value shall be used for all cells in the test.
Access Service Class (ASC#0) ‑ Persistence value			1	Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
T_SI		s	1.28	The value shall be used for all cells in the test.
DRX cycle length		s	1.28	The value shall be used for all cells in the test.
T1		s	15
T2		s	15

Table A.4.2B: Cell re-selection to intra-frequency TDD cell

Parameter	Unit	Cell 1				Cell 2				Cell 3
Timeslot Number		0		8		0		8		0		8
		T1	T2	T1	T2	T1	T2	T1	T2	T1	T2	T1	T2
UTRA RF Channel Number		Channel 1				Channel 1				Channel 1
PCCPCH_Ec/Ior	dB	-3	-3			-3	-3			-3	-3
SCH_Ec/Ior	dB	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9
SCH_t_offset		0	0	0	0	5	5	5	5	10	10	10	10
PICH_Ec/Ior	dB			-3	-3			-3	-3			-3	-3
OCNS_Ec/Ior	dB	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12
	dB	9	7	9	7	7	9	7	9	-1	-1	-1	-1
PCCPCH RSCP	dBm	-64	-66			-66	-64			-74	-74
Qoffset1_s,n	dB	C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1,C6:0				C2, C1: 0; C2, C3:0; C2,C4:0 C2, C5: 0; C2,C6:0				C3, C1: 0; C3, C2:0; C3,C4:0 C3, C5: 0; C3,C6:0
Qhyst 1_s	dB	0				0				0
Treselection	s	0				0				0
Sintrasearch	dB	not sent				not sent				not sent
		Cell 4				Cell 5				Cell 6
Timeslot		0		8		0		8		0		8
		T1	T2	T1	T2	T1	T2	T1	T2	T1	T2	T1	T2
UTRA RF Channel Number		Channel 1				Channel 1				Channel 1
PCCPCH_Ec/Ior	dB	-3	-3			-3	-3			-3	-3
SCH_Ec/Ior	dB	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9
SCH_t_offset		15	15	15	15	20	20	20	20	25	25	25	25
PICH_Ec/Ior	dB			-3	-3			-3	-3			-3	-3
OCNS_Ec/Ior	dB	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12
	dB	-1	-1	-1	-1	-1	-1	-1	-1	-1	-1	-1	-1
PCCPCH RSCP	dBm	-74	-74			-74	-74			-74	-74
Qoffset1_s,n	dB	C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0				C5, C1: 0; C5, C2:0; C5,C3:0 C5, C4:0; C5, C6:0				C6, C1: 0; C6, C2:0; C6,C3:0 C6, C4:0; C6, C5:0
Qhyst1_s	dB	0				0				0
Treselection	s	0				0				0
Sintrasearch	dB	not sent				not sent				not sent
	dBm/7,68 MHz	-70
Propagation Condition		AWGN

A.4.2.1.2 Test Requirements

A.4.2.1.2.1 3.84 Mcps TDD option

The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send the RRC CONNECTION REQUEST message to perform a Location Registration on cell 2.

The cell re-selection delay shall be less than 8 s.

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE:

The cell re-selection delay can be expressed as: T_evaluateTDD + T_SI, where:

T_evaluateTDDA DRX cycle length of 1280ms is assumed for this test case, this leads to a T_{evaluate TDD} of 6.4s according to Table 4.1 in section 4.2.2.7.

T_SIMaximum repetition rate of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.

This gives a total of 7.68 s, allow 8s in the test case.

A.4.2.1.2.2 1.28 Mcps TDD option

The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send SYNCH-UL sequence in the UpPTS for sending the RRC CONNECTION REQUEST to perform a Location Registration on cell 2.

The cell re-selection delay shall be less than 8 s.

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE:

The cell re-selection delay can be expressed as: T_evaluateNTDD + T_SI, where:

T_evaluateNTDD: A DRX cycle length of 1280ms is assumed for this test case, this leads to a T_{evaluate NTDD} of 6.4s according to Table 4.1A in section 4.2.

T_SI: Time required for receiving all the relevant system information data according to the reception procedure and the RRC procedure delay of system information blocks defined in 25.331 for a UTRAN cell (ms). 1280 ms is assumed in this test case.

This gives a total of 7.68 s, allow 8s in the test case.

A.4.2.1.2.3 7.68 Mcps TDD option

The cell re-selection delay shall be less than 8 s.

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE:

The cell re-selection delay can be expressed as: T_evaluateTDD + T_SI, where:

T_evaluateTDDA DRX cycle length of 1280ms is assumed for this test case, this leads to a T_{evaluate TDD} of 6.4s according to Table 4.1B in section 4.2.2.7.

T_SIMaximum repetition rate of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.

This gives a total of 7.68 s, allow 8s in the test case.

A.4.2.2 Scenario 2: Cell re-selection to inter-frequency TDD cell

A.4.2.2.1 Test Purpose and Environment

This test is to verify the requirement for the cell re-selection delay in the multi carrier case reported in section 4.2.2.

A.4.2.2.1.1 3.84 Mcps TDD option

This scenario implies the presence of 2 carriers and 6 cells as given in Table A.4.3 and A.4.4. Cell 1 and cell 2 shall belong to different Location Areas.

Table A.4.3: General test parameters for Cell Re-selection to inter-frequency TDD cell

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1
Initial condition	Neighbour cells		Cell2, Cell3,Cell4, Cell5, Cell6
Final condition	Active cell		Cell2
HCS			Not used
UE_TXPWR_MAX_RACH		dBm	21	The value shall be used for all cells in the test.
Qrxlevmin		dBm	-102	The value shall be used for all cells in the test.
Access Service Class (ASC#0) ‑ Persistence value			1	Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
T_SI		s	1.28	The value shall be used for all cells in the test.
DRX cycle length		s	1.28	The value shall be used for all cells in the test.
T1		s	30
T2		s	15

Table A.4.4: Cell re-selection to iner-frequency TDD cell

Parameter	Unit	Cell 1					Cell 2				Cell 3
Timeslot Number		0			8		0		8		0		8
		T1		T2	T1	T2	T1	T2	T1	T2	T1	T2	T1	T2
UTRA RF Channel Number		Channel 1					Channel 2				Channel 1
PCCPCH_Ec/Ior	dB	-3		-3			-3	-3			-3	-3
SCH_Ec/Ior	dB	-9		-9	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9
SCH_t_offset		0		0	0	0	5	5	5	5	10	10	10	10
PICH_Ec/Ior	dB				-3	-3			-3	-3			-3	-3
OCNS_Ec/Ior	dB	-3,12		-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12
	dB	6		0	6	0	0	6	0	6	-3	-3	-3	-3
PCCPCH RSCP	dBm	-67		-73			-73	-67			-76	-76
Qoffset1_s,n	dB	C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1, C6:0					C2, C1: 0; C2, C3:0; C2,C4:0 C2, C5:0; C2, C6:0				C3, C1: 0; C3, C2:0; C3,C4:0 C3, C5:0; C3, C6:0
Qhyst1_s	dB	0					0				0
Treselection	s	0					0				0
Sintrasearch	dB	not sent					not sent				not sent
Sintersearch	dB	not sent					not sent				not sent
		Cell 4					Cell 5				Cell 6
Timeslot		0			8		0		8		0		8
		T1	T2		T1	T2	T1	T2	T1	T2	T1	T2	T1	T2
UTRA RF Channel Number		Channel 1					Channel 2				Channel 2
PCCPCH_Ec/Ior	dB	-3		-3			-3	-3			-3	-3
SCH_Ec/Ior	dB	-9		-9	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9
SCH_t_offset		15		15	15	15	20	20	20	20	25	25	25	25
PICH_Ec/Ior	dB				-3	-3			-3	-3			-3	-3
OCNS	dB	-3,12		-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12
	dB	-3		-3	-3	-3	-3	-3	-3	-3	-3	-3	-3	-3
PCCPCH RSCP	dBm	-76		-76			-76	-76			-76	-76
Qoffset1_s,n	dB	C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0					C5, C1: 0; C5, C2:0; C5,C3:0 C5, C4:0; C5, C6:0				C6, C1: 0; C6, C2:0; C6,C3:0 C6, C4:0; C6, C5:0
Qhyst1_s	dB	0					0				0
Treselection	s	0					0				0
Sintrasearch	dB	not sent					not sent				not sent
Sintersearch	dB	not sent					not sent				not sent
	dBm/3,84 MHz	-70
Propagation Condition		AWGN

A.4.2.2.1.2 1.28 Mcps TDD option

This scenario implies the presence of 2 carriers and 6 cells as given in Table A.4.3A and A.4.4A. The UE is requested to monitor neighbouring cells on 2 carriers. Cell 1 and cell 2 shall belong to different Location Areas.

Table A.4.3A: General test parameters for Cell Re-selection to inter-frequency TDD cell

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1
Initial condition	Neighbour cells		Cell2, Cell3,Cell4, Cell5, Cell6
Final condition	Active cell		Cell2
HCS			Not used
UE_TXPWR_MAX_RACH		dBm	21	The value shall be used for all cells in the test.
Qrxlevmin		dBm	-103	The value shall be used for all cells in the test.
Access Service Class (ASC#0) ‑ Persistence value			1	Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
T_SI		s	1.28	The value shall be used for all cells in the test.
DRX cycle length		s	1.28	The value shall be used for all cells in the test.
T1		s	30
T2		s	15

Table A.4.4A: Cell re-selection to inter-frequency TDD cell

Parameter	Unit	Cell 1				Cell 2				Cell 3
Timeslot Number		0		DWPTS		0		DWPTS		0		DWPTS
		T1	T2	T1	T2	T1	T2	T1	T2	T1	T2	T1	T2
UTRA RF Channel Number		Channel 1				Channel 2				Channel 1
PCCPCH_Ec/Ior	dB	-3	-3			-3	-3			-3	-3
DwPCH_Ec/Ior	dB			0	0			0	0			0	0
OCNS_Ec/Ior	dB	-3	-3			-3	-3			-3	-3
	dB	10	4	10	4	4	10	4	10	-1	-1	-1	-1
PCCPCH RSCP	dBm	-63	-69			-69	-63			-74	-74
Qoffset1_s,n	dB	C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1, C6:0				C2, C1: 0; C2, C3:0; C2,C4:0C2, C5:0; C2, C6:0				C3, C1: 0; C3, C2:0; C3,C4:0 C3, C5:0; C3, C6:0
Qhyst1_s	dB	0				0				0
Treselection	s	0				0				0
Sintrasearch	dB	not sent				not sent				not sent
Sintersearch	dB	not sent				not sent				not sent
		Cell 4				Cell 5				Cell 6
Timeslot		0		DWPTS		0		DWPTS		0		DWPTS
		T1	T2	T1	T2	T1	T2	T1	T2	T1	T2	T1	T2
UTRA RF Channel Number		Channel 1				Channel 2				Channel 2
PCCPCH_Ec/Ior	dB	-3	-3			-3	-3			-3	-3
DwPCH_Ec/Ior	dB			0	0			0	0			0	0
OCNS_Ec/Ior	dB	-3	-3			-3	-3			-3	-3
	dB	-1	-1	-1	-1	-1	-1	-1	-1	-1	-1	-1	-1
PCCPCH RSCP	dBm	-74	-74			-74	-74			-74	-74
Qoffset1_s,n	dB	C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0				C5, C1: 0; C5, C2:0; C5,C3:0 C5, C4:0; C5, C6:0				C6, C1: 0; C6, C2:0; C6,C3:0 C6, C4:0; C6, C5:0
Qhyst1_s	dB	0				0				0
Treselection	s	0				0				0
Sintrasearch	dB	not sent				not sent				not sent
Sintersearch	dB	not sent				not sent				not sent
	dBm/ 1.28 MHz	-70
Propagation Condition		AWGN
NOTE: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number.

A.4.2.2.1.3 7.68 Mcps TDD option

This scenario implies the presence of 2 carriers and 6 cells as given in Table A.4.3B and A.4.4B. Cell 1 and cell 2 shall belong to different Location Areas.

Table A.4.3B: General test parameters for Cell Re-selection to intra-frequency TDD cell

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1
Initial condition	Neighbour cells		Cell2, Cell3,Cell4, Cell5, Cell6
Final condition	Active cell		Cell2
HCS			Not used
UE_TXPWR_MAX_RACH		dBm	21	The value shall be used for all cells in the test.
Qrxlevmin		dBm	-102	The value shall be used for all cells in the test.
Access Service Class (ASC#0) ‑ Persistence value			1	Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
T_SI		s	1.28	The value shall be used for all cells in the test.
DRX cycle length		s	1.28	The value shall be used for all cells in the test.
T1		s	30
T2		s	15

Table A.4.4B: Cell re-selection to inter-frequency TDD cell

Parameter	Unit	Cell 1				Cell 2				Cell 3
Timeslot Number		0		8		0		8		0		8
		T1	T2	T1	T2	T1	T2	T1	T2	T1	T2	T1	T2
UTRA RF Channel Number		Channel 1				Channel 2				Channel 1
PCCPCH_Ec/Ior	dB	-3	-3			-3	-3			-3	-3
SCH_Ec/Ior	dB	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9
SCH_t_offset		0	0	0	0	5	5	5	5	10	10	10	10
PICH_Ec/Ior	dB			-3	-3			-3	-3			-3	-3
OCNS_Ec/Ior	dB	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12
	dB	6	0	6	0	0	6	0	6	-3	-3	-3	-3
PCCPCH RSCP	dBm	-67	-73			-73	-67			-76	-76
Qoffset1_s,n	dB	C1, C2: 0; C1, C3:0; C1,C4:0 C1, C5:0; C1, C6:0				C2, C1: 0; C2, C3:0; C2,C4:0 C2, C5:0; C2, C6:0				C3, C1: 0; C3, C2:0; C3,C4:0 C3, C5:0; C3, C6:0
Qhyst1_s	dB	0				0				0
Treselection	s	0				0				0
Sintrasearch	dB	not sent				not sent				not sent
Sintersearch	dB	not sent				not sent				not sent
		Cell 4				Cell 5				Cell 6
Timeslot		0		8		0		8		0		8
		T1	T2	T1	T2	T1	T2	T1	T2	T1	T2	T1	T2
UTRA RF Channel Number		Channel 1				Channel 2				Channel 2
PCCPCH_Ec/Ior	dB	-3	-3			-3	-3			-3	-3
SCH_Ec/Ior	dB	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9	-9
SCH_t_offset		15	15	15	15	20	20	20	20	25	25	25	25
PICH_Ec/Ior	dB			-3	-3			-3	-3			-3	-3
OCNS	dB	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12
	dB	-3	-3	-3	-3	-3	-3	-3	-3	-3	-3	-3	-3
PCCPCH RSCP	dBm	-76	-76			-76	-76			-76	-76
Qoffset1_s,n	dB	C4, C1: 0; C4, C2:0; C4,C3:0 C4, C5:0; C4, C6:0				C5, C1: 0; C5, C2:0; C5,C3:0 C5, C4:0; C5, C6:0				C6, C1: 0; C6, C2:0; C6,C3:0 C6, C4:0; C6, C5:0
Qhyst1_s	dB	0				0				0
Treselection	s	0				0				0
Sintrasearch	dB	not sent				not sent				not sent
Sintersearch	dB	not sent				not sent				not sent
	dBm/7,68 MHz	-70
Propagation Condition		AWGN

A.4.2.2.2 Test Requirements

A.4.2.2.2.1 3.84 Mcps TDD option

The cell re-selection delay shall be less than 8 s.

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE:

The cell re-selection delay can be expressed as: T_evaluateTDD + T_SI, where:

T_evaluateTDDA DRX cycle length of 1280ms is assumed for this test case, this leads to a T_{evaluate TDD} of 6.4s according to Table 4.1 in section 4.2.2.7.

T_SIMaximum repetition rate of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.

This gives a total of 7.68 s, allow 8s in the test case.

A.4.2.2.2.2 1.28 Mcps TDD option

The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send the SYNCH-UL sequence in the UpPTS for sending the RRC CONNECTION REQUEST to perform a Location Registration on cell 2.

The cell re-selection delay shall be less than 8 s.

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE:

The cell re-selection delay can be expressed as: T_evaluateNTDD + T_SI, where:

T_evaluateNTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a T_{evaluate NTDD} of 6.4s according to Table 4.1A in section 4.2.

T_SI Time required for receiving all the relevant system information data according to the reception procedure and the RRC procedure delay of system information blocks defined in 25.331 for a UTRAN cell (ms). 1280 ms is assumed in this test case.

This gives a total of 7.68 s, allow 8s in the test case.

A.4.2.2.2.3 7.68 Mcps TDD option

The cell re-selection delay shall be less than 8 s.

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE:

The cell re-selection delay can be expressed as: T_evaluateTDD + T_SI, where:

T_evaluateTDDA DRX cycle length of 1280ms is assumed for this test case, this leads to a T_{evaluate TDD} of 6.4s according to Table 4.1B in section 4.2.2.7.

T_SIMaximum repetition rate of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.

This gives a total of 7.68 s, allow 8s in the test case.

A.4.2.2A Scenario 2A: 3.84 Mcps TDD cell re-selection for 1.28 Mcps TDD UE

A.4.2.2A.1 Test Purpose and Environment

This test is to verify the requirement for the 1.28 Mcps TDD OPTION/3.84 Mcps TDD OPTION cell re-selection delay reported in section 4.2.

This scenario implies the presence of 1 low chip rate (1.28 Mcps TDD OPTION) and 1 high chip rate (3.84 Mcps TDD OPTION)) cell as given in Table A.4.3B and A.4.4B.

The ranking of the cells shall be made according to the cell reselection criteria specified in TS25.304.

Cell 1 and cell 2 shall belong to different Location Areas.

Table A.4.3B: General test parameters for TDD low chip rate to TDD high chip rate cell re-selection

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1	1.28 Mcps TDD OPTION cell
Initial condition	Neighbour cell		Cell2	3.84 Mcps TDD OPTION cell
Final condition	Active cell		Cell2	3.84 Mcps TDD OPTION cell
HCS			Not used
UE_TXPWR_MAX_RACH		dBm	21	The value shall be used for all cells in the test.
Access Service Class (ASC#0) ‑ Persistence value			1	Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
T_SI		s	1,28	The value shall be used for all cells in the test.
DRX cycle length		s	1,28	The value shall be used for all cells in the test.
T1		s	30
T2		s	15

Table A.4.4B: Test parameters for TDD low chip rate to TDD high chip rate cell re-selection

Parameter	Unit	Cell 1				Cell 2
Timeslot Number		0		DwPTS		0		8

		T1	T2	T 1	T 2	T1	T2	T 1	T 2
UTRA RF Channel Number (NOTE)		Channel 1				Channel 2
PCCPCH_Ec/Ior	dB	-3	-3			-3	-3
DwPCH_Ec/Ior	dB			0	0	n.a.		n.a.
SCH_Ec/Ior	dB	n.a.		n.a.		-9	-9	-9	-9
SCH_t_offset		n.a.		n.a.		0	0	0	0
PICH_Ec/Ior	dB							-3	-3
OCNS_Ec/Ior	dB	-3		n.a.		-3,12	-3,12	-3,12	-3,12
	dB	10	7			7	10	7	10
		-70 dBm/ 1.28 MHz				-70 dBm/ 3.84 MHz
PCCPCH_RSCP	dBm	-63	-66			-66	-63
Qrxlevmin	dBm	-103				-103
Qoffset1_s,n	dB	C1, C2: 0				C2, C1: 0
Qhyst1_s	dB	0				0
Treselection	s	0				0
Sintersearch	dB	not sent				not sent
Propagation Condition		AWGN				AWGN
NOTE: In the case of multi-frequency cell for 1.28 Mcps TDD option, the UTRA RF Channel Number is the primary frequency’s channel number.

A.4.2.2A.2 Test Requirements

The cell re-selection delay shall be less than 8 s.

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE: The cell re-selection delay can be expressed as:

T_evaluateTDD + T_SI

where:

T_evaluateTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a T_{evaluate TDD} of 6.4s according to Table 4.1A in section 4.2.

T_SI Time required for receiving all the relevant system information data according to the reception procedure and the RRC procedure delay of system information blocks defined in [16] for a UTRAN cell (ms). 1280 ms is assumed in this test case.

This gives a total of 7.68 s, allow 8s in the test case.

A.4.2.2B Scenario 2B: 3.84 Mcps/1.28 Mcps TDD cell re-selection

A.4.2.2B.1 Test Purpose and Environment

This test is to verify the requirement for the 3.84 Mcps/1.28 Mcps TDD cell re-selection delay reported in section 4.2.

This scenario implies the presence of 1 3.84 Mcps TDD serving cell, and 1 1.28 Mcps TDD cell to be re-selected. The UE is requested to monitor neighbouring cells on 1 3.84Mcps TDD carrier and 1 1.28Mcps TDD carrier. Test parameters are given in Table A.4.3C, A4.4C, and A.4.4D. Cell 1 and cell 2 shall belong to different Location Areas.

Table A.4.3C: General test parameters for 3.84 Mcps /1.28 Mcps TDD cell re-selection

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell 1	3.84 Mcps TDD OPTION cell
Initial condition	Neighbour cell		Cell 2	1.28 Mcps TDD OPTION cell
Final condition	Active cell		Cell 2	1.28 Mcps TDD OPTION cell
HCS			Not used
UE_TXPWR_MAX_RACH		dBm	21	The value shall be used for all cells in the test.
Q_rxlevmin		dBm	-103
Access Service Class (ASC#0) ‑ Persistence value			1	Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
T_SI		s	1,28	The value shall be used for all cells in the test.
DRX cycle length		s	1,28	The value shall be used for all cells in the test.
T1		s	30
T2		s	15

Table A.4.4C: Cell 1 specific test parameters for 3.84 Mcps TDD/1.28 Mcps TDD cell re-selection

Parameter		Unit		Cell 1
Timeslot Number				0		8
				T1	T2	T 1	T 2
UTRA RF Channel Number				Channel 1
PCCPCH_Ec/Ior		dB		-3	-3
SCH_Ec/Ior		dB		-9	-9	-9	-9
SCH_t_offset				0
PICH_Ec/Ior		dB				-3	-3
OCNS_Ec/Ior		dB		-3.12
		dB		10	7	10	7
PCCPCH_RSCP		dBm		-63	-66
Qoffset1_s,n		dB		C1, C2: 0
Qhyst1_s		dB		0
Treselection		s		0
Sintersearch		dB		not sent
	dBm/3.84 MHz		-70
Propagation Condition				AWGN

Table A.4.4D: Cell 2 specific test parameters for 3.84 Mcps TDD/1.28 Mcps TDD cell re-selection

Parameter		Unit	Cell 2
Timeslot Number			0		DwPTS
			T1	T2	T 1	T 2
UTRA RF Channel Number*			Channel 2
PCCPCH_Ec/Ior	dB		-3	-3
DwPCH_Ec/Ior	dB				0	0
OCNS_Ec/Ior	dB		-3
	dB		7	10	7	10
PCCPCH_RSCP	dBm		-66	-63
Qoffset1_s,n	dB		C2, C1: 0
Qhyst1_s	dB		0
Treselection	s		0
Sintersearch	dB		not sent
	dBm/1.28 MHz		-70
Propagation Condition			AWGN
* Note: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number.

A.4.2.2B.2 Test Requirements

The cell re-selection delay shall be less than 8 s.

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE: The cell re-selection delay can be expressed as:

T_evaluateNTDD + T_SI

where:

T_evaluateNTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a T_{evaluate NTDD} of 6.4s according to Table 4.1 in section 4.2.

T_SI Time required for receiving all the relevant system information data according to the reception procedure and the RRC procedure delay of system information blocks defined in [16] for a UTRAN cell (ms). 1280 ms is assumed in this test case.

This gives a total of 7.68 s, allow 8s in the test case.

A.4.2.2C Scenario 2C: 3.84 Mcps TDD cell re-selection for 7.68 Mcps TDD UE

A.4.2.2C.1 Test Purpose and Environment

This test is to verify the requirement for the 7.68 Mcps TDD OPTION/3.84 Mcps TDD OPTION cell re-selection delay reported in section 4.2.

This scenario implies the presence of 1 higher chip rate (7.68 Mcps TDD OPTION) and 1 high chip rate (3.84 Mcps TDD OPTION)) cell as given in Table A.4.4E and A4.4F.

The ranking of the cells shall be made according to the cell reselection criteria specified in TS25.304.

Cell 1 and cell 2 shall belong to different Location Areas.

Table A.4.4E: General test parameters for TDD higher chip rate (7.68 Mcps) to TDD high chip rate (3.84 Mcps) cell re-selection

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1	7.68 Mcps TDD OPTION cell
Initial condition	Neighbour cell		Cell2	3.84 Mcps TDD OPTION cell
Final condition	Active cell		Cell2	3.84 Mcps TDD OPTION cell
HCS			Not used
UE_TXPWR_MAX_RACH		dBm	21	The value shall be used for all cells in the test.
Qrxlevmin		dBm	-102	The value shall be used for all cells in the test.
Access Service Class (ASC#0) ‑ Persistence value			1	Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
T_SI		S	1,28	The value shall be used for all cells in the test.
DRX cycle length		S	1,28	The value shall be used for all cells in the test.
T1		S	30
T2		S	15

Table A.4.4F: Test parameters for TDD higher chip rate (7.68 Mcps) to TDD high chip rate (3.84 Mcps) cell re-selection

Parameter	Unit	Cell 1				Cell 2
Timeslot Number		0		8		0		8
		T1	T2	T 1	T 2	T1	T2	T 1	T 2
UTRA RF Channel Number		Channel 1				Channel 2
PCCPCH_Ec/Ior	dB	-3	-3			-3	-3
SCH_Ec/Ior	dB	-9	-9	-9	-9	-9	-9	-9	-9
SCH_t_offset		0	0	0	0	5	5	5	5
PICH_Ec/Ior	dB			-3	-3			-3	-3
OCNS_Ec/Ior		-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12
	dB	10	7	10	7	7	10	7	10
PCCPCH_RSCP	dBm	-63	-66			-66	-63
Qoffset1_s,n	dB	C1, C2: 0				C2, C1: 0
Qhyst1_s	dB	0				0
Treselection	s	0				0
Sintersearch	dB	not sent				not sent
		-70 dBm/7.68 MHz				-70 dBm/3.84 MHz
Propagation Condition		AWGN

A.4.2.2C.2 Test Requirements

The cell re-selection delay shall be less than 8 s.

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE: The cell re-selection delay can be expressed as:

T_evaluateTDD + T_SI

where:

T_evaluateTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a T_{evaluate TDD} of 6.4s according to Table 4.1B in section 4.2.

T_SI Maximum repetition rate of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.

This gives a total of 7.68 s, allow 8s in the test case.

A.4.2.2D Scenario 2D: 3.84 Mcps/7.68 Mcps TDD cell re-selection

A.4.2.2D.1 Test Purpose and Environment

This test is to verify the requirement for the 3.84 Mcps/7.68 Mcps TDD cell re-selection delay reported in section 4.2.

This scenario implies the presence of one 3.84 Mcps TDD serving cell, and one 7.68 Mcps TDD cell to be re-selected. The UE is requested to monitor neighbouring cells on one 3.84Mcps TDD carrier and one 7.68 Mcps TDD carrier. Test parameters are given in Table A.4.4G and A.4.4H. Cell 1 and cell 2 shall belong to different Location Areas.

Table A.4.4G: General test parameters for 3.84 Mcps /7.68 Mcps TDD cell re-selection

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell 1	3.84 Mcps TDD OPTION cell
Initial condition	Neighbour cell		Cell 2	7.68 Mcps TDD OPTION cell
Final condition	Active cell		Cell 2	7.68 Mcps TDD OPTION cell
HCS			Not used
UE_TXPWR_MAX_RACH		dBm	21	The value shall be used for all cells in the test.
Q_rxlevmin		dBm	-102
Access Service Class (ASC#0) ‑ Persistence value			1	Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
T_SI		S	1,28	The value shall be used for all cells in the test.
DRX cycle length		S	1,28	The value shall be used for all cells in the test.
T1		S	30
T2		S	15

Table A.4.4H: Cell 1 specific test parameters for 3.84 Mcps TDD/7.68 Mcps TDD cell re-selection

Parameter	Unit	Cell 1				Cell 2
Timeslot Number		0		8		0		8
		T1	T2	T 1	T 2	T1	T2	T 1	T 2
UTRA RF Channel Number		Channel 1				Channel 2
PCCPCH_Ec/Ior	dB	-3	-3			-3	-3
SCH_Ec/Ior	dB	-9	-9	-9	-9	-9	-9	-9	-9
SCH_t_offset		0	0	0	0	5	5	5	5
PICH_Ec/Ior	dB			-3	-3			-3	-3
OCNS_Ec/Ior		-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12	-3,12
	dB	10	7	10	7	7	10	7	10
PCCPCH_RSCP	dBm	-63	-66			-66	-63
Qoffset1_s,n	dB	C1, C2: 0				C2, C1: 0
Qhyst1_s	dB	0				0
Treselection	s	0				0
Sintersearch	dB	not sent				not sent
		-70 dBm/3.84 MHz				-70 dBm/7.68 MHz
Propagation Condition		AWGN

A.4.2.2E Scenario 2E: 1.28Mcps TDD inter-band cell re-selection

A.4.2.2E.1 Test Purpose and Environment

This test is to verify the requirement for the cell re-selection delay in the inter-band reported in section 4.2.2.

This scenario implies the presence of 2 carriers and 6 cells as given in Table A.4.4J and A.4.4K. The UE is requested to monitor neighbouring cells on 2 band carriers. Cell 1 and cell 2 shall belong to different Location Areas.

Table A.4.4I: General test parameters for Cell Re-selection to inter-frequency TDD cell

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1
Initial condition	Neighbour cells		Cell2, Cell3,Cell4, Cell5, Cell6
Final condition	Active cell		Cell2
HCS			Not used
UE_TXPWR_MAX_RACH		dBm	21	The value shall be used for all cells in the test.
Qrxlevmin		dBm	-103	The value shall be used for all cells in the test.
Access Service Class (ASC#0) ‑ Persistence value			1	Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
T_SI		s	1.28	The value shall be used for all cells in the test.
DRX cycle length		s	1.28	The value shall be used for all cells in the test.
T1		s	30
T2		s	15

A.4.2.2E.2 Test Requirements

The cell re-selection delay shall be less than 8 s.

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE: The cell re-selection delay can be expressed as:

T_evaluateNTDD + T_SI

where:

T_evaluateNTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a T_{evaluate NTDD} of 6.4s according to Table 4.1 in section 4.2.

T_SI Time required for receiving all the relevant system information data according to the reception procedure and the RRC procedure delay of system information blocks defined in [16] for a UTRAN cell (ms). 1280 ms is assumed in this test case.

This gives a total of 7.68 s, allow 8s in the test case.

A.4.2.3 Scenario 3: TDD/FDD cell re-selection

A.4.2.3.1 Test Purpose and Environment

A.4.2.3.1.1 3.84 Mcps TDD option

This test is to verify the requirement for the TDD/FDD cell re-selection delay reported in section 4.2.2.

This scenario implies the presence of 1 UTRA TDD and 1 UTRA FDD cell as given in Table A.4.5 and A.4.6. The maximum repetition period of the relevant system information blocks that need to be received by the UE to camp on a cell shall be 1280 ms.

Cell 1 and cell 2 shall belong to different Location Areas.

Table A.4.5: General test parameters for the TDD/FDD cell re-selection

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1	TDD cell
Initial condition	Neighbour cells		Cell2	FDD cell
Final condition	Active cell		Cell2
HCS			Not used
UE_TXPWR_MAX_RACH		dBm	21	The value shall be used for all cells in the test.
Access Service Class (ASC#0) ‑ Persistence value			1	Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
DRX cycle length		s	1.28	The value shall be used for all cells in the test.
T1		s	30	During T1 cell 1 better ranked than cell 2
T2		s	15	During T2 cell 2 better ranked than cell 1

Table A.4.6: TDD/FDD cell re-selection

Parameter	Unit	Cell 1				Cell 2
Timeslot Number		0		8		n.a	n.a.
		T1	T2	T 1	T 2	T 1	T 2
UTRA RF Channel Number		Channel 1				Channel 2
CPICH_Ec/Ior	dB	n.a.		n.a.		-10	-10
PCCPCH_Ec/Ior	dB	-3	-3			-12	-12
SCH_Ec/Ior	dB	-9	-9	-9	-9	-12	-12
SCH_t_offset		0	0	0	0	n.a.	n.a.
PICH_Ec/Ior	dB			-3	-3	-15	-15
OCNS_EcIor	dB	-3,12	-3,12	-3,12	-3,12	-0,941	-0,941
	dB	3	-2	3	-2	-2	3
	dBm/3.84 MHz	-70
CPICH_RSCP	dBm	n.a.		n.a.		-82	-77
PCCPCH_RSCP	dBm	-70	-75			n.a.	n.a.
Cell_selection_and reselection_quality _measure		CPICH_RSCP				CPICH_RSCP
Qrxlevmin	dBm	-102				-115
Qoffset1_s,n	dB	C1, C2: -12				C2, C1: +12
Qhyst1_s	dB	0				0
Treselection	s	0				0
Propagation Condition		AWGN				AWGN

A.4.2.3.1.2 1.28 Mcps TDD option

This test is to verify the requirement for the 1.28 Mcps TDD OPTION/FDD cell re-selection delay reported in section 4.2.

This scenario implies the presence of 1 1.28Mps TDD serving cell, and 1 FDD cell to be selected. The UE is requested to monitor neighbouring cells on 1 1.28Mcps TDD carrier and 1 FDD carrier. Test parameters are given in Table A.4.5A, A4.6A, and A.4.6AA.

Cell 1 and cell 2 shall belong to different Location Areas.

Table A.4.5A: General test parameters for the TDD/FDD cell re-selection

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1	1.28 Mcps TDD OPTION cell
Initial condition	Neighbour cells		Cell2	FDD cell
Final condition	Active cell		Cell2	FDD cell
HCS			Not used
UE_TXPWR_MAX_RACH		dBm	21	The value shall be used for all cells in the test.
Access Service Class (ASC#0) ‑ Persistence value			1	Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
T_SI		s	1.28	The value shall be used for all cells in the test.
DRX cycle length		s	1.28	The value shall be used for all cells in the test.
T1		s	30
T2		s	15

Table A.4.6A: Cell 1 specific test parameters for 1.28 Mcps TDD/FDD cell re-selection

Parameter	Unit	Cell 1
Timeslot Number		0		DwPTS
		T1	T2	T 1	T 2
UTRA RF Channel Number*		Channel 1
PCCPCH_Ec/Ior	dB	-3	-3
DwPCH_Ec/Ior	dB			0	0
OCNS_Ec/Ior	dB	-3
	dB	8	2	8	2
PCCPCH_RSCP	dBm	-65	-71
Cell_selection_and_ reselection_quality_measure		CPICH RSCP
Qrxlevmin	dBm	-103
Qoffset1_s,n	dB	C1, C2: -12
Qhyst1_s	dB	0
Treselection	s	0
Sintersearch	dB	not sent
	dBm/1.28 MHz	-70
Propagation Condition		AWGN
* Note: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number.

Table A.4.6AA: Cell 2 specific test parameters for 1.28 Mcps TDD/FDD cell re-selection

Parameter	Unit	Cell 2 (UTRA)
		T1	T2
UTRA RF Channel Number		Channel 2
CPICH_Ec/Ior	dB	-10
PCCPCH_Ec/Ior	dB	-12
SCH_Ec/Ior	dB	-12
PICH_Ec/Ior	dB	-15
OCNS_Ec/Ior	dB	-0.941
	dB	-3		3
CPICH_RSCP	dBm	-83		-77
Cell_selection_and_ reselection_quality_measure		CPICH RSCP
Qrxlevmin	dBm	-115
Qoffset1_{s, n}	dB	C2, C1: +12
Qhyst1	dB	0
Treselection	s	0
Sintersearch	dB	not sent
	dBm/3.84 MHz	‑70
Propagation Condition		AWGN

A.4.2.3.1.3 7.68 Mcps TDD option

This test is to verify the requirement for the TDD/FDD cell re-selection delay reported in section 4.2.2.

This scenario implies the presence of 1 UTRA TDD and 1 UTRA FDD cell as given in Table A.4.5B and A.4.6B. The maximum repetition period of the relevant system information blocks that need to be received by the UE to camp on a cell shall be 1280 ms.

Cell 1 and cell 2 shall belong to different Location Areas.

Table A.4.5B: General test parameters for the TDD/FDD cell re-selection

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1	TDD cell
Initial condition	Neighbour cells		Cell2	FDD cell
Final condition	Active cell		Cell2
HCS			Not used
UE_TXPWR_MAX_RACH		dBm	21	The value shall be used for all cells in the test.
Access Service Class (ASC#0) ‑ Persistence value			1	Selected so that no additional delay is caused by the random access procedure. The value shall be used for all cells in the test.
DRX cycle length		s	1.28	The value shall be used for all cells in the test.
T1		s	30	During T1 cell 1 better ranked than cell 2
T2		s	15	During T2 cell 2 better ranked than cell 1

Table A.4.6B: TDD/FDD cell re-selection

Parameter	Unit	Cell 1				Cell 2
Timeslot Number		0		8		n.a	n.a.
		T1	T2	T 1	T 2	T 1	T 2
UTRA RF Channel Number		Channel 1				Channel 2
CPICH_Ec/Ior	dB	n.a.		n.a.		-10	-10
PCCPCH_Ec/Ior	dB	-3	-3			-12	-12
SCH_Ec/Ior	dB	-9	-9	-9	-9	-12	-12
SCH_t_offset		0	0	0	0	n.a.	n.a.
PICH_Ec/Ior	dB			-3	-3	-15	-15
OCNS_EcIor	dB	-3,12	-3,12	-3,12	-3,12	-0,941	-0,941
	dB	3	-2	3	-2	-2	3
		-70 dBm/7.68 MHz				-70 dBm/3.84 MHz
CPICH_RSCP	dBm	n.a.		n.a.		-82	-77
PCCPCH_RSCP	dBm	-70	-75			n.a.	n.a.
Cell_selection_and reselection_quality _measure		CPICH_RSCP				CPICH_RSCP
Qrxlevmin	dBm	-102				-115
Qoffset1_s,n	dB	C1, C2: -12				C2, C1: +12
Qhyst1_s	dB	0				0
Treselection	s	0				0
Propagation Condition		AWGN				AWGN

A.4.2.3.2 Test Requirements

A.4.2.3.2.1 3.84 Mcps TDD option

The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message to perform a Location Registration on cell 2.

The cell re-selection delay shall be less than 8 s.

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE:

The cell re-selection delay can be expressed as: T_evaluateFDD + T_SI, where:

T_evaluateFDDSee Table 4.1 in section 4.2.2.

T_SIMaximum repetition rate of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.

This gives a total of 7.68 s, allow 8s in the test case.

A.4.2.3.2.2 1.28 Mcps TDD option

The cell re-selection delay shall be less than 8 s.

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE: The cell re-selection delay can be expressed as:

T_evaluateFDD + T_SI

where:

T_evaluateFDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a T_{evaluate FDD} of 6.4s according to Table 4.1A in section 4.2.

This gives a total of 7.68 s, allow 8s in the test case.

A.4.2.3.2.3 7.68 Mcps TDD option

The cell re-selection delay shall be less than 8 s.

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE:

The cell re-selection delay can be expressed as:

T_evaluateFDD + T_SI, where:

T_evaluateFDDA DRX cycle length of 1280ms is assumed for this test case, this leads to a T_{evaluate FDD} of 6.4s according to Table 4.1B in section 4.2.

T_SIMaximum repetition rate of relevant system info blocks that needs to be received by the UE to camp on a cell. 1280 ms is assumed in this test case.

This gives a total of 7.68 s, allow 8s in the test case.

A.4.2.4 Scenario 4: inter RAT cell re-selection

A.4.2.4.1 Test Purpose and Environment

A.4.2.4.1.1 3.84 Mcps TDD option

This test is to verify the requirement for the UTRA TDD to GSM cell re-selection delay reported in section 4.2.

This scenario implies the presence of 1 UTRA TDD serving cell, and 1 GSM cell to be re-selected. The UE is requested to monitor neighbouring cells on 1 UTRA TDD carrier and 12 GSM cells. Test parameters are given in Table, A.4.7, A.4.8, A.4.9. Cell 1 and Cell 2 shall belong to different Location Areas.

For this test environment the ranking/mapping function indicated in the broadcast of cell 1 shall be in such a way as to enable the UE to evaluate that the TDD cell 1 is better ranked as the GSM cell 2 during T1 and the GSM cell 2 is better ranked than the TDD cell 1 during T2.

Table A.4.7: General test parameters for UTRAN to GSM Cell Re-selection

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1	UTRA TDD Cell
Initial condition	Neighbour cell		Cell2	GSM Cell
Final condition	Active cell		Cell2
HCS			Not used
DRX cycle length		s	1,28	UTRA TDD cell
T1		s	45
T2		s	35

Table A.4.8: Cell re-selection UTRA TDD to GSM cell case (cell 1)

Parameter		Unit	Cell 1 (UTRA TDD)
Timeslot Number			0			8
			T1		T2	T1	T2
UTRA RF Channel Number			Channel 1			Channel 1
PCCPCH_Ec/Ior	dB		-3		-3
SCH_Ec/Ior	dB		-9		-9	-9	-9
SCH_t_offset			0		0	0	0
PICH_Ec/Ior	dB					-3	-3
OCNS_Ec/Ior	dB		-3,12		-3,12	-3,12	-3,12
	dB		3		-2	3	-2
	dBm/3,84 MHz		-70			-70
PCCPCH RSCP	dBm		-70	-75		n.a.	n.a.
Propagation Condition			AWGN			AWGN
Qrxlevmin	dBm		-102
Qoffset1_{s, n}	dB		C1, C2: 0
Qhyst1	dB		0
Treselection	s		0
Ssearch_RAT	dB		not sent

Table A.4.9: Cell re-selection UTRA TDD to GSM cell case (cell 2)

Parameter	Unit	Cell 2 (GSM)
		T1		T2
Absolute RF Channel Number		ARFCN 1
RXLEV	dBm	-90	-75
RXLEV_ACCESS_MIN	dBm	-104
MS_TXPWR_MAX_CCH	dBm	33

A.4.2.4.1.2 1.28 Mcps TDD option

This test is to verify the requirement for the UTRAN to GSM cell re-selection delay reported in section 4.2.

This scenario implies the presence of 1 UTRAN serving cell, and 1 GSM cell to be re-selected. Test parameters are given in Table A.4.7A, A.4.8A, A.4.9A.

The ranking of the cells shall be made according to the cell reselection criteria specified in TS25.304. Cell 1 and cell 2 shall belong to different location areas.

Table A.4.7A: General test parameters for UTRAN (1.28 Mcps TDD OPTION) to GSM Cell Re-selection

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1	1.28 Mcps TDD OPTION cell
Initial condition	Neighbour cell		Cell2	GSM cell
Final condition	Active cell		Cell2	GSM cell
DRX cycle length		s	1,28
HCS			Not used
T1		s	45
T2		s	15

Table A.4 8A: Cell re-selection UTRAN to GSM cell case (cell 1)

Parameter		Unit	Cell 1 (UTRA)
Timeslot Number			0			DwPTS
			T1		T2	T1	T2
UTRA RF Channel Number*			Channel 1			Channel 1
PCCPCH_Ec/Ior	dB		-3		-3
DwPCH_Ec/Ior	dB					0	0
OCNS_Ec/Ior	dB		-3		-3
	dB		13		-12	13	-12
	dBm/1.28 MHz		-80
PCCPCH RSCP	dBm		-70	-95		n.a.	n.a.
Propagation Condition			AWGN			AWGN

Treselection	s		0
Ssearch_RAT	dB		Not sent
Qrxlevmin	dBm		-103
Qoffset1_s,n	dB		C1, C2: 0
Qhyst1_s	dB		0
* Note: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number.

Table A.4.9A: Cell re-selection UTRAN to GSM cell case (cell 2)

Parameter	Unit	Cell 2 (GSM)
		Cell 2 (GSM)		T1	T2
Absolute RF Channel Number		ARFCN 1
RXLEV	dBm	-75	-75
RXLEV_ACCESS_MIN	dBm	-104
MS_TXPWR_MAX_CCH	dBm	33

A.4.2.4.1.3 7.68 Mcps TDD option

This test is to verify the requirement for the UTRA TDD to GSM cell re-selection delay reported in section 4.2.

This scenario implies the presence of 1 UTRA TDD serving cell, and 1 GSM cell to be re-selected. The UE is requested to monitor neighbouring cells on 1 UTRA TDD carrier and 12 GSM cells. Test parameters are given in Table, A.4.7B, A.4.8B, A.4.9B. Cell 1 and Cell 2 shall belong to different Location Areas.

Table A.4.7B: General test parameters for UTRAN to GSM Cell Re-selection

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1	UTRA TDD Cell
Initial condition	Neighbour cell		Cell2	GSM Cell
Final condition	Active cell		Cell2
HCS			Not used
DRX cycle length		s	1,28	UTRA TDD cell
T1		s	45
T2		s	35

Table A.4.8B: Cell re-selection UTRA TDD to GSM cell case (cell 1)

Parameter		Unit	Cell 1 (UTRA TDD)
Timeslot Number			0			8
			T1		T2	T1	T2
UTRA RF Channel Number			Channel 1			Channel 1
PCCPCH_Ec/Ior	dB		-3		-3
SCH_Ec/Ior	dB		-9		-9	-9	-9
SCH_t_offset			0		0	0	0
PICH_Ec/Ior	dB					-3	-3
OCNS_Ec/Ior	dB		-3,12		-3,12	-3,12	-3,12
	dB		3		-2	3	-2
	dBm/7,68 MHz		-70			-70
PCCPCH RSCP	dBm		-70	-75		n.a.	n.a.
Propagation Condition			AWGN			AWGN
Qrxlevmin	dBm		-102
Qoffset1_{s, n}	dB		C1, C2: 0
Qhyst1	dB		0
Treselection	s		0
Ssearch_RAT	dB		not sent

Table A.4.9B: Cell re-selection UTRA TDD to GSM cell case (cell 2)

Parameter	Unit	Cell 2 (GSM)
		T1		T2
Absolute RF Channel Number		ARFCN 1
RXLEV	dBm	-90	-75
RXLEV_ACCESS_MIN	dBm	-104
MS_TXPWR_MAX_CCH	dBm	33

A.4.2.4.2 Test Requirements

A.4.2.4.2.1 3.84 Mpcs TDD option

The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send the RR Channel Request message for location update to Cell 2.

The cell re-selection delay shall be less than 26 s + T_BCCH, where T_BCCH is the maximum time allowed to read BCCH data in the GSM cell [21].

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE: The cell re-selection delay can be expressed as:

4 * T_measureGSM + T_BCCH

where:

T_measureGSM Equal to the value specified in Table 4.1 in section 4.2

T_BCCH Equal to 1.9 s, i.e. the maximum time allowed to read BCCH data when synchronised to a BCCH carrier from a GSM cell [21].

This gives a total of 25.6 s + T_BCCH, allow 26 s + T_BCCH in the test case.

A.4.2.4.2.2 1.28 Mpcs TDD option

The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send RR Channel Request message to perform a Location update.

The cell re-selection delay shall be less than 8 s + T_BCCH where T_BCCH is the maximum time allowed to read BCCH data from GSM cell [21].

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE: The cell re-selection delay can be expressed as:

Max(3*T_measureNTDD , T_{measure GSM}+1DRX)+ T_BCCH

where:

T_measureNTDD A DRX cycle length of 1280ms is assumed for this test case, this leads to a T_measureNTDD of 1.28s according to Table 4.1A in section 4.2.

T_measureGSM A DRX cycle length of 1280ms is assumed for this test case, this leads to a T_measureGSM of 6.4s according to Table 4.1A in section 4.2.

DRX cycle length 1.28s is assumed, see Table A.4.1A

T_BCCHMaximum time allowed to read BCCH data from GSM cell [20].

According to [21], the maximum time allowed to read the BCCH data, when being synchronized to a BCCH carrier, is 1.9 s.

This gives a total of 7.68s +T_BCCH, thus allow 8s +T_BCCH.

A.4.2.4.2.3 7.68 Mpcs TDD option

The cell re-selection delay shall be less than 26 s + T_BCCH, where T_BCCH is the maximum time allowed to read BCCH data in the GSM cell [21].

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE: The cell re-selection delay can be expressed as:

4 * T_measureGSM + T_BCCH

where:

T_measureGSM Equal to the value specified in Table 4.1B in section 4.2

T_BCCH Equal to 1.9 s, i.e. the maximum time allowed to read BCCH data when synchronised to a BCCH carrier from a GSM cell [21].

This gives a total of 25.6 s + T_BCCH, allow 26 s + T_BCCH in the test case.

A.4.2.4.3 Scenario 4A Test Purpose and Environment

A.4.2.4.3.1 (void)

A.4.2.4.3.2 1.28 Mcps TDD option

This test is to verify the requirement for the UTRAN to GSM cell re-selection delay reported in section 4.2.

This scenario implies the presence of 1 UTRAN serving cell, and 1 GSM cell to be re-selected. Test parameters are given in Table A.4.10A, A.4.11A, A.4.12A.

The ranking of the cells shall be made according to the cell reselection criteria specified in TS25.304. Cell 1 and cell 2 shall belong to different location areas.

Table A.4.10A: General test parameters for UTRAN (1.28 Mcps TDD OPTION) to GSM Cell Re-selection

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1	1.28 Mcps TDD OPTION cell
Initial condition	Neighbour cell		Cell2	GSM cell
Final condition	Active cell		Cell2	GSM cell
DRX cycle length		s	1,28
HCS			Not Used
T1		s	45
T2		s	45

Table A.4 11A: Cell re-selection UTRAN to GSM cell case (cell 1)

Parameter		Unit	Cell 1 (UTRA)
Timeslot Number			0			DwPTS
			T1		T2	T1	T2
UTRA RF Channel Number (NOTE)			Channel 1			Channel 1
PCCPCH_Ec/Ior	dB		-3		-3
DwPCH_Ec/Ior	dB					0	0
OCNS_Ec/Ior	dB		-3		-3
	dB		6		6	6	6
	dBm/1.28 MHz		-80
PCCPCH RSCP	dBm		-77	-77
Propagation Condition			AWGN			AWGN
Treselection	s		0
Ssearch_RAT	dB		Not sent
Qrxlevmin	dBm		-103
Qoffset1_s,n	dB		C1, C2: 0
Qhyst1_s	dB		0
NOTE: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number.

Table A.4.12A: Cell re-selection UTRAN to GSM cell case (cell 2)

Parameter	Unit	Cell 2 (GSM)
		Cell 2 (GSM)		T1	T2
Absolute RF Channel Number		ARFCN 1
RXLEV	dBm	-90	-70
RXLEV_ACCESS_MIN	dBm	-104
MS_TXPWR_MAX_CCH	dBm	33

A.4.2.4.4 Scenario 4A Requirements

A.4.2.4.4.1 (void)

A.4.2.4.4.2 1.28 Mpcs TDD option

The cell re-selection delay is defined as the time from the beginning of time period T2, to the moment when the UE camps on Cell 2, and starts to send RR Channel Request message for location update to Cell 2.

The cell re-selection delay shall be less than 26 s+ T_BCCH, where T_BCCH is the maximum time allowed to read BCCH data from GSM cell [21].

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE: The UE shall keep a running average of 4 measurements, thus gives 4* T_measureGSM +T_BCCH, where:

T_measureGSM A DRX cycle length of 1280ms is assumed for this test case, this leads to a T_measureGSM of 6.4s according to Table 4.1A in section 4.2.

T_BCCHMaximum time allowed to read BCCH data from GSM cell [21].

According to [21], the maximum time allowed to read the BCCH data, when being synchronized to a BCCH carrier, is 1.9 s.

This gives a total of 25.6s +T_BCCH, thus allow 26s +T_BCCH.

A.4.2.4.5 Scenario 4B: HCS with only UTRA level changed

A.4.2.4.5.1 Test Purpose and Environment

A.4.2.4.5.1.1 3.84 Mcps TDD option

Void.

A.4.2.4.5.1.2 1.28 Mcps TDD option

This test is to verify the requirement for the UTRAN to GSM cell re-selection delay reported in section 4.2 when measurement rules according to HCS is used.

This scenario implies the presence of 1 UTRAN serving cell, and 1 GSM cell to be re-selected. Test parameters are given in Table A.4.13B, A.4.14B, A.4.15B.

Cell 1 and cell 2 shall belong to different location areas.

Table A.4.13B: General test parameters for UTRAN (1.28 Mcps TDD option) to GSM Cell Re-selection

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell1	1.28 Mcps TDD option cell
Initial condition	Neighbour cell		Cell2	GSM cell
Final condition	Active cell		Cell2	GSM cell
DRX cycle length		s	1,28
HCS			Used
T1		s	45
T2		s	45

Table A.4 14B: Cell re-selection UTRAN to GSM cell case (cell 1)

Parameter		Unit	Cell 1 (UTRA)
Timeslot Number			0			DwPTS
			T1		T2	T1	T2
UTRA RF Channel Number (NOTE)			Channel 1			Channel 1
PCCPCH_Ec/Ior	dB		-3		-3
DwPCH_Ec/Ior	dB					0	0
OCNS_Ec/Ior	dB		-3		-3
	dB		13		-12	13	-12
	dBm/1.28 MHz		-80
PCCPCH RSCP	dBm		-70	-95
Propagation Condition			AWGN			AWGN
Treselection	s		0
Ssearch_RAT	dB		Not sent
Qrxlevmin	dBm		-103
Qoffset1_s,n	dB		C1, C2: 0
Qhyst1_s	dB		0
T_reselection	s		0
Ssearch_RAT	dB		0
Penalty_time	s		0 (default value)
HCS_PRIO			0 (default value)
Q_hcs			0 (default value)
T_Crmax	s		not used (default value)
NOTE: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number.

Table A.4.15B: Cell re-selection UTRAN to GSM cell case (cell 2)

Parameter	Unit	Cell 2 (GSM)
		Cell 2 (GSM)		T1	T2
Absolute RF Channel Number		ARFCN 1
RXLEV	dBm	-80	-80
RXLEV_ACCESS_MIN	dBm	-104
MS_TXPWR_MAX_CCH	dBm	33
Qsearch_I		always

A.4.2.4.5.1.3 7.68 Mcps TDD option

Void.

A.4.2.4.5.2 Requirements

A.4.2.4.5.2.1 3.84 Mcps TDD option

Void.

A.4.2.4.5.2.2 1.28 Mcps TDD option

The cell re-selection delay is defined as the time from when the cell quality levels change to the moment when this change makes the UE reselect a cell, and starts to send LOCATION UPDATING REQUEST message to perform a Location update to the new cell.

The cell re-selection delay shall be less than 37.7 s+ T_BCCH, where T_BCCH is the maximum time allowed to read BCCH data from GSM cell.

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE: The cell re-selection delay can be expressed as: 30 s + T_measureGSM+ DRX cycle length + T_BCCH, where::

T_measureGSM A DRX cycle length of 1280ms is assumed for this test case, this leads to a T_measureGSM of 6.4s according to Table 4.1A in section 4.2.

DRX cycle length A DRX cycle length of 1280ms is assumed for this test case.

T_BCCHMaximum time allowed to read BCCH data from GSM cell.

The maximum time allowed to read the BCCH data, when being synchronized to a BCCH carrier, is 1.9 s.

This gives a total of 37.68 s +T_BCCH, thus allow 37.7 s +T_BCCH.

A.4.2.4.5.2.3 7.68 Mcps TDD option

Void.

A.4.2.5 Scenario 5: TDD/E-UTRA cell re-selection

A.4.2.5.1 UTRA to E-UTRA TDD cell re-selection: E-UTRA is of higher priority

A.4.2.5.1.1 Test Purpose and Environment

A.4.2.5.1.1.1 3.84 Mcps TDD option

A.4.2.5.1.1.2 1.28 Mcps TDD option

This test is to verify the requirement for the UTRA TDD to E-UTRA TDD inter-RAT cell re-selection requirements specified in section 4.2.2.5a when the E-UTRA cell is of higher priority.

This test scenario comprised of 1 UTRA TDD serving cell, and 1 E-UTRA TDD cell to be re-selected. Test parameters are given in table A.4.2.5.1.1.2-1, A.4.2.5.1.1.2-2, and A.4.2.5.1.1.2-3. The test consists of three successive time periods, with time duration of T1, T2 and T3 respectively. UTRA cell 1 is already identified by the UE prior to the start of the test. At T1 the UE is camped on to cell 1. Cell 2 is of higher priority than cell 1.

The ranking of the cells shall be made according to the cell reselection criteria specified in TS25.304.

Table A.4.2.5.1.1.2-1: General test parameters for UTRAN (1.28 Mcps TDD OPTION) to E-UTRAN TDD Cell Re-selection

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell 1	UE is on cell 1 in the initialisation phase, so that reselection to cell 2 occurs during the first T2 phase
T2 end condition	Active cell		Cell 2	UE shall perform reselection to cell 2 during T2
T2 end condition	Neighbour cell		Cell 1	UTRA 1.28 Mcps TDD option cell
T3 end condition	Active cell		Cell 1	UE shall perform reselection to cell 1 during T3
T3 end condition	Neighbour cell		Cell 2	E-UTRA TDD cell
Uplink-downlink configuration of cell 2			1	As specified in table 4.2.2 in TS 36.211
Special subframe configuration of cell 2			6	As specified in table 4.2.1 in TS 36.211
PRACH configuration of cell 2			53	As specified in table 4.7.1-3 in TS 36.211
CP length of cell 2			Normal
Time offset between cells			3 ms	Asynchronous cells
Access Barring Information		–	Not sent	No additional delays in random access procedure.
Treselection		s	0
DRX cycle length		s	1,28
HCS			Not used
T1		s	>20	During T1, cell 2 shall be powered off, and during the off time the physical layer cell identity shall be changed, The intention is to ensure that cell 2 has not been detected by the UE prior to the start of period T2
T2		s	85	T2 need to be defined so that cell re-selection reaction time is taken into account.
T3		s	25	T3 need to be defined so that cell re-selection reaction time is taken into account.

Table A.4.2.5.1.1.2-2: Cell specific test parameters for cell re-selection UTRA TDD to E-UTRA TDD test case (cell 1)

Parameter		Unit	Cell 1 (UTRA)
Timeslot Number			0			DwPTS
			T1	T2	T3	T1	T2	T3
UTRA RF Channel Number ^Note1			Channel 1
PCCPCH_Ec/Ior	dB		-3	-3	-3
DwPCH_Ec/Ior	dB					0	0	0
OCNS_Ec/Ior	dB		-3	-3	-3
	dB		11	11	11	11	11	11
	dBm/1.28 MHz		-80
PCCPCH RSCP	dBm		-72	-72	-72	n.a.
Propagation Condition			AWGN
Q_rxlevmin	dBm		-103
Qoffset1_s,n	dB		C1, C2: 0
Q_hyst1s	dB		0
Thresh_{x, high} ^Note2	dB		46 (-94dBm)
S_{prioritysearch1}	dB		24 (-79dBm)
S_{prioritysearch2}	dB		0
Ssearch_E-UTRA	dB		Not send
Note1: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number. Note2: This refers to the value of Thresh_{x, high}which is included in UTRA system information, and is a threshold for the E-UTRA target cell

Table A.4.2.5.1.1.2-3: Cell specific test parameters for cell re-selection UTRA TDD to E-UTRA TDD test case (cell 2)

Parameter	Unit	Cell 2
Parameter	Unit	T1	T2	T3
E-UTRA RF Channel Number		2
BWchannel	MHz	10
PBCH_RA	dB	0	0	0
PBCH_RB	dB
PSS_RB	dB
SSS_RB	dB
PCFICH_PA	dB
PHICH_PA	dB
PHICH_PB	dB
PDCCH_PA	dB
PDCCH_PB	dB
PDSCH_PA	dB
PDSCH_PB	dB
OCNG_RA^{Note 1}	dB
OCNG_RB^{Note 1}	dB
Q_rxlevmin	dBm/15kHz	-140	-140	-140
	dBm/15kHz	-98
RSRP	dBm/15kHz	-inf	-87	-101
	dB	-inf	11	-3
S_{nonintrasearch}	dB	Not sent
Thresh_{serving, low}	dB	46 (-94dBm)
Thresh_{x, low} ^Note2	dB	24 (-79dBm)
Propagation Condition		AWGN
Note 1: OCNG shall be used such that cell is fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols. Note2: This refers to the value of Thresh_{x, low} which is included in E-UTRA system information, and is a threshold for the UTRA target cell

A.4.2.5.1.1.3 7.68 Mcps TDD option

A.4.2.5.1.2 Test Requirements

A.4.2.5.1.2.1 3.84 Mpcs TDD option

A.4.2.5.1.2.2 1.28 Mpcs TDD option

The cell reselection delay to higher priority is defined as the time from the beginning of time period T2, to the moment when the UE camps on cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message on cell 2.

The cell re-selection delay to higher priority shall be less than 81s.

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE: The cell re-selection delay to higher priority cell can be expressed as: T_{higher_priority_search} + T_{evaluateE-UTRA} + T_SI,

Where:

T_{higher_priority_search} 60s, See section 4.2.2.5a

T_{evaluateE-UTRA} 19.2s, See Table 4.2A in section 4.2.2.7

T_SI Maximum repetition period of relevant system info blocks that needs to be received by the UE to camp on a cell; 1280 ms is assumed in this test case.

This gives a total of 80.48 s, allow 81 s for higher priority cell reselection in the test case.

A.4.2.5.1.2.3 7.68 Mpcs TDD option

A.4.2.5.2 UTRA to E-UTRA TDD cell re-selection: E-UTRA is of lower priority

A.4.2.5.2.1 Test Purpose and Environment

A.4.2.5.2.1.1 3.84 Mcps TDD option

A.4.2.5.2.1.2 1.28 Mcps TDD option

This test is to verify the requirement for the UTRA TDD to E-UTRA TDD inter-RAT cell re-selection requirements specified in section 4.2.2.5a when the E-UTRA cell is of lower priority.

This test scenario comprised of 1 UTRA TDD serving cell, and 1 E-UTRA TDD cell to be re-selected. Test parameters are given in table A.4.2.5.2.1.2-1, A.4.2.5.2.1.2-2, and A.4.2.5.2.1.2-3. The test consists of two successive time periods, with time duration of T1 and T2 respectively. At T1 the UE is camped on to cell 1. Cell 2 is of lower priority than cell 1.

The ranking of the cells shall be made according to the cell reselection criteria specified in TS25.304.

Table A.4.2.5.2.1.2-1: General test parameters for UTRAN (1.28 Mcps TDD OPTION) to E-UTRAN TDD Cell Re-selection

Parameter		Unit	Value	Comment
Initial condition	Active cell		Cell 1	UTRA 1.28 Mcps TDD option cell
T1 end condition	Active cell		Cell1	UE shall perform reselection to cell 1 during T1 for subsequent iterations of the test.
T1 end condition	Neighbour cell		Cell2	E-UTRA TDD cell
T2 end condition	Active cell		Cell2	UE shall perform reselection to cell 2 during T2
T2 end condition	Neighbour cell		Cell1	UTRA 1.28 Mcps TDD option cell
Uplink-downlink configuration of cell 2			1	As specified in table 4.2.2 in TS 36.211
Special subframe configuration of cell 2			6	As specified in table 4.2.1 in TS 36.211
PRACH configuration of cell 2			53	As specified in table 4.7.1-3 in TS 36.211
CP length of cell 2			Normal
Time offset between cells			3 ms	Asynchronous cells
Access Barring Information		–	Not sent	No additional delays in random access procedure.
Treselection		s	0
DRX cycle length		s	1,28
HCS			Not used
T1		s	85	T1 need to be defined so that cell re-selection reaction time is taken into account.
T2		s	25	T2 need to be defined so that cell re-selection reaction time is taken into account.

Table A.4.2.5.2.1.2-2: Cell specific test parameters for cell re-selection UTRA TDD to E-UTRA TDD test case (cell 1)

Parameter		Unit	Cell 1 (UTRA)
Timeslot Number			0			DwPTS
			T1		T2	T1	T2
UTRA RF Channel Number ^Note1			Channel 1
PCCPCH_Ec/Ior	dB		-3		-3
DwPCH_Ec/Ior	dB					0	0
OCNS_Ec/Ior	dB		-3		-3
	dB		11		-3	11	-3
	dBm/1.28 MHz		-80
PCCPCH RSCP	dBm		-72	-86		n.a.	n.a.
Propagation Condition			AWGN
Q_rxlevmin	dBm		-103
Qoffset1_s,n	dB		C1, C2: 0
Q_hyst1s	dB		0
Thresh_{serving, low}	dB		24 (-79dBm)
Thresh_{x, low} ^Note2	dB		46 (-94dBm)
S_{prioritysearch1}	dB		62
S_{prioritysearch2}	dB		0
Ssearch_E-UTRA	dB		Not send
Note1: In the case of multi-frequency cell, the UTRA RF Channel Number is the primary frequency’s channel number. Note2: This refers to the value of Thresh_{x, low}which is included in UTRA system information, and is a threshold for the E-UTRA target cell

Table A.4.2.5.2.1.2-3: Cell specific test parameters for cell re-selection UTRA TDD to E-UTRA TDD test case (cell 2)

Parameter	Unit	Cell 2
Parameter	Unit	T1	T2
E-UTRA RF Channel Number		2
BW_channel	MHz	10
PBCH_RA	dB	0	0
PBCH_RB	dB
PSS_RB	dB
SSS_RB	dB
PCFICH_PA	dB
PHICH_PA	dB
PHICH_PB	dB
PDCCH_PA	dB
PDCCH_PB	dB
PDSCH_PA	dB
PDSCH_PB	dB
OCNG_RA^Note1	dB
OCNG_RB^Note1	dB
Q_rxlevmin	dBm/15kHz	-140	-140
	dBm/15kHz	-98
RSRP	dBm/15kHz	-87	-87
	dB	11	11
Thresh_{x, high} ^Note2	dB	24(-79dBm)
S_{nonintrasearch}	dB	46
Propagation Condition		AWGN
Note1: OCNG shall be used such that cell is fully allocated and a constant total transmitted power spectral density is achieved for all OFDM symbols. Note2: This refers to the value of Thresh_{x, high}which is included in E-UTRA system information, and is a threshold for the UTRA target cell

A.4.2.5.2.1.3 7.68 Mcps TDD option

A.4.2.5.2.2 Test Requirements

A.4.2.5.2.2.1 3.84 Mpcs TDD option

A.4.2.5.2.2.2 1.28 Mpcs TDD option

The cell reselection delay to lower priority is defined as the time from the beginning of time period T2, to the moment when the UE camps on cell 2, and starts to send preambles on the PRACH for sending the RRC CONNECTION REQUEST message on cell 2.

The cell re-selection delay to lower priority shall be less than 21s.

The rate of correct cell reselections observed during repeated tests shall be at least 90%.

NOTE: The cell re-selection delay to lower priority cell can be expressed as: T_{evaluateE-UTRA} + T_SI,

Where:

T_{evaluateE-UTRA} 19.2s, See Table 4.2A in section 4.2.2.7

T_SI Maximum repetition period of relevant system info blocks that needs to be received by the UE to camp on a cell; 1280 ms is assumed in this test case.

This gives a total of 20.48 s, allow 21 s for lower priority cell reselection in the test case.

A.4.2.5.2.2.3 7.68 Mpcs TDD option