BSIC

Base Station Identification Code (NCC + BCC)

0-63

6

SCH D/L

BSIC

Base Station Identification Code (NCC + BCC+RCC)

0-511

9

For EC operation: NCC+BCC+RCC

9

EC-SCH D/L

For PEO operation: NCC+BCC

6

SCH D/L

For PEO operation: RCC

3

CCCH D/L,

BCCH D/L

BA

BCCH Allocation

‑

‑

BCCH D/L

BA_IND

Sequence number of BA

0/1

1

BCCH D/L

SACCH D/L

3G_BA_IND

Sequence number of 3G neighbour cell list and/or E-UTRAN neighbour cell list

0/1

1

BCCH D/L

SACCH D/L

SI 23_BA_IND

Sequence number of E-UTRAN neighbour cell list (see note 4)

0/1

1

BCCH D/L

MS_TXPWR_MAX_CCH

The maximum TX power level an

0/31

5

BCCH D/L

MS is allowed to use when accessing the

system until otherwise commanded.

LB_MS_TXPWR_MAX_CCH

The maximum TX power level an MS is allowed to use on all other than DCS 1800 and PCS 1900 frequency bands when accessing the system until otherwise commanded.

0 = 43 dBm, 1 = 41 dBm, 2 = 39 dBm,…,18 = 7 dBm, 19 = 5 dBm, 20 = 5 dBm,…,31 = 5 dBm.

0-31

5

BCCH D/L

POWER OFFSET

The power offset will be used in conjunction

0‑3

2

BCCH D/L

with the MS TXPWR MAX CCH parameter

by the class 3 DCS 1 800 MS:

0 = 0 dB

1 = 2 dB

2 = 4 dB

3 = 6 dB

RXLEV_ACCESS_MIN

Minimum received signal level at the MS

0‑63

6

BCCH D/L

required for access to the system.

RADIO_LINK_TIMEOUT

The maximum value of the radio

‑

4

BCCH D/L

link counter 4‑64 SACCH blocks,

SACCH D/L

15 steps of 4 SACCH blocks

CELL_RESELECT_HYSTERESIS

RXLEV hysteresis for required

0‑7

3

BCCH D/L

cell re‑selection. 0‑14 dB, 2 dB

steps, i.e. 0 = 0 dB, 1 = 2 dB, etc.

NCC_PERMITTED

Bit map of NCCs for which the MS is permitted to report measurement results.
Bit map relates to NCC part of BSIC.

‑

8

BCCH D/L

SACCH D/L

CELL_BAR_ACCESS

See table 1a.

0/1

1

BCCH D/L

CELL_BAR_QUALIFY

See table 1a.

0/1

1

BCCH D/L

CELL_BAR_QUALIFY_3

See tables 1b and 1c.

0-3

2

BCCH D/L

CELL_RESELECT_OFFSET

Applies an offset to the C2

0‑63

6

BCCH D/L

reselection criterion. 0 ‑ 126 dB,

2 dB steps, i.e. 0 = 0 dB, 1 = 2 dB, etc.

TEMPORARY_OFFSET

Applies a negative offset to C2 for

0‑7

3

BCCH D/L

the duration of PENALTY_TIME.

0 ‑ 60 dB, 10 dB steps i.e. 0 = 0 dB,.

1 = 10 dB, etc. and 7 = infinity

PENALTY_TIME

Gives the duration for which the

0‑31

5

BCCH D/L

temporary offset is applied.

20 to 620 s, 20 s steps, i.e.

0 = 20 s, 1 = 40 s, etc.

31 is reserved to indicate that

CELL_RESELECT_OFFSET is

subtracted from C2 and

TEMPORARY_OFFSET is ignored.

continued

LSA_OFFSET

Applies an offset to be used for LSA cell re- selection between cells with the same LSA priorities.

0 = 0 dB, 1 = 4 dB, 2 = 8 dB, 3 = 16 dB,

4 = 24 dB, 5 = 32 dB, 6 = 48 dB, 7 =64 dB

0-7

3

BCCH D/L

PRIO_THR

The PRIO signal strength threshold is related to RXLEV_ACCESS_MIN.

0 = 0 dB, 1 = 6 dB, 2 = 12 dB, 3 = 18 dB

4 = 24 dB, 5 = 30 dB, 6 = 36 dB, 7 =  dB

0-7

3

BCCH D/L

LSA ID

The LSA identities for the cell

BCCH D/L

Qsearch_I

Search for UTRAN FDD cells if signal level is below (0‑7) or above (8‑15) threshold
0 = – 98 dBm, 1 = – 94 dBm, … ,
6 = – 74 dBm, 7 =  (always)
8 = – 78 dBm, 9 = – 74 dBm, … ,
14 = – 54 dBm, 15 =  (never).
Default value =  (never).

Search for UTRAN TDD cells if signal level is below (0‑7) or above (8‑15) threshold

0 = – 98 dBm, 1 = – 94 dBm, … ,
6 = – 74 dBm, 7 =  (always)
8 = – 90 dBm, 9 = – 86 dBm, … ,
14 = – 66 dBm, 15 =  (never).
Default value =  (never).

0-15

4

BCCH D/L

Qsearch_C_Initial

Indicates the Qsearch value to be used in connected mode before Qsearch_C is received,
0 = use Qsearch_I, 1 =  (always).
Default value = use Qsearch_I.

0/1

1

BCCH D/L

FDD_Qoffset

Applies an offset to RLA_C for UTRAN FDD cell re‑selection.
0 = –  (always select a cell if acceptable),
1 = -28 dB, 2 = -24 dB, … , 15 = 28 dB.
Default value = 0 dB.

0-15

4

BCCH D/L

TDD_Qoffset

An absolute threshold of RSCP for UTRAN TDD cell re-selection,

0 = -105dBm, 1 = -102dBm, 2=-99dBm, 3 = -96dBm, 4 = -93dBm, 5 = -90dBm, 6 = -87dBm, 7 = -84dBm, 8 = -81dBm, 9 = -78dBm, 10 = -75dBm, 11 = -72dBm, 12 = -69dBm, 13 = -66dBm, 14 = -63dBm, 15 = -60dBm.

Default value = -90dBm.

0-15

4

BCCH D/L

FDD_Qmin

A minimum threshold for Ec/No for UTRAN FDD cell re-selection,
0= -20dB, 1= -6dB, 2= -18dB, 3= -8dB, 4= -16dB, 5= -10dB, 6= -14dB, 7= -12dB.

Default value= -12dB.

0-7

3

BCCH D/L

FDD_Qmin_Offset

Applies an offset to FDD_Qmin value,

0 = 0 dB, 1 = 2 dB, 2 = 4 dB, 3 = 6 dB, 4 = 8 dB, 5 = 10 dB, 6 = 12 dB, 7 = 14 dB.

Default value = 0 dB.

0-7

3

BCCH D/L

FDD_RSCPmin

A minimum threshold of RSCP for UTRAN FDD cell re-selection,

0 = -114 dBm, 1 = -112 dBm, 2 = -110 dBm, 3 = -108 dBm, 4 = -106 dBm, 5 = -104 dBm, 6 = -102 dBm, 7 = -100 dBm, 8 = -98 dBm, 9 = -96 dBm, 10 = -94 dBm, 11 = -92 dBm, 12 = -90 dBm, 13 = -88 dBm, 14 = -86 dBm, 15 = -84 dBm.

Default value = -102 dBm.

0-15

4

BCCH D/L

THRESH_GSM_low

A threshold below which the MS is allowed to reselect to lower priority layers,

0 = 0 dB, 1 = 2 dB, 2 = 4 dB, …, 13 = 26 dB, 14 = 28 dB, 15 =  (always).

0-15

4

BCCH D/L

continued

THRESH_priority_search

A threshold for the serving cell that controls measurement of inter-RAT cells or frequencies of lower priority when the priority-based cell reselection algorithm is used,

0 = -98 dBm, 1 = -95 dBm, 2 = -92 dBm, …, 13 = -59 dBm, 14 = -56  dBm, 15 =  (always).

0-15

4

BCCH D/L

GERAN_PRIORITY

Priority of GSM cells,

0 = lowest priority, …, 7 = highest priority.

0-7

3

BCCH D/L

UTRAN_QRXLEVMIN

Minimum required RX level for cells on the target UTRAN frequency (dBm),

0 = -119 dBm, 1 = -117 dBm, 2 = -115 dBm, …, 30 = -59  dBm, 31 = -57 dBm.

Default value = -119 dBm.

0-31

5

BCCH D/L

THRESH_UTRAN_high, THRESH_UTRAN_low

Reselection thresholds towards UTRAN FDD or TDD cells,

0 = 0 dB, 1 = 2 dB, 2 = 4 dB, 3 = 6 dB, …, 30 = 60 dB, 31 = 62 dB.

Default value of THRESH_UTRAN_low = value of THRESH_UTRAN_high.

0-31

5

BCCH D/L

UTRAN_PRIORITY

Priority of a UTRAN frequency layer, 0 = lowest priority, …, 7 = highest priority.

0-7

3

BCCH D/L

E-UTRAN_QRXLEVMIN

Minimum required RX level for cells on the target E-UTRAN frequency (dBm),

0 = -140 dBm, 1 = -138 dBm, 2 = -136 dBm, …, 30 = -80 dBm, 31 = -78 dBm.

Default value = -140 dBm.

0-31

5

BCCH D/L

THRESH_E-UTRAN_high, THRESH_E-UTRAN_low

Reselection thresholds towards E-UTRAN FDD or TDD cells,

0 = 0 dB, 1 = 2 dB, 2 = 4 dB, 3 = 6 dB, …, 30 = 60 dB, 31 = 62 dB.

Default value of THRESH_E-UTRAN_low = value of THRESH_E‑UTRAN_high.

0-31

5

BCCH D/L

E-UTRAN_PRIORITY

Priority of a E-UTRAN frequency layer, 0 = lowest priority, …, 7 = highest priority.

0-7

3

BCCH D/L

H_PRIO

Hysteresis used in the priority reselection algorithm,

0 =  (rule disabled), 1 = 5 dB, 2 = 4 dB, 3 = 3 dB.

0-3

2

BCCH D/L

T_reselection

Time hysteresis in the reselection algorithm,

0 = 5 sec, 1 = 10 sec, 2 = 15 sec, 3 = 20 sec.

Default value = 0 (5 sec)

0-3

2

BCCH D/L

Qsearch_C_E-UTRAN_Initial

Indicates the Qsearch value to be used in dedicated / dual transfer mode before Qsearch_C_E-UTRAN is received,
Search for E-UTRAN cells if signal level below threshold (0-7):
– 98, – 94, … , – 74 dBm,  (always)
or above threshold (8-15):
– 78, – 74, … , – 54 dBm,  (never)

0-15

4

BCCH D/L

E-UTRAN_Qmin

Minimum required quality for cells on the target E-UTRAN frequency (dB),

0= -34dB, 1= -32dB, 2= -30dB, …, 14= -6dB, 15= -4dB.

Default value= -34dB.

0-15

4

BCCH D/L

E-UTRAN_RSRPmin

Minimum required RX level for cells on the target E-UTRAN frequency (dBm),

0 = -140 dBm, 1 = -138 dBm, 2 = -136 dBm, …, 30 = -80 dBm, 31 = -78 dBm.

Default value = -140 dBm.

0-31

5

BCCH D/L

E-UTRAN_QQUALMIN

Minimum required quality for cells on the target E-UTRAN frequency (dB),

0= -34dB, 1= -32dB, 2= -30dB, …, 14= -6dB, 15= -4dB.

Default value= -34dB.

0-15

4

BCCH D/L

continued

THRESH_E-UTRAN_high_Q, THRESH_E-UTRAN_low_Q

Reselection thresholds towards E-UTRAN FDD or TDD cells,

0 = 0 dB, 1 = 1 dB, 2 = 2 dB, 3 = 3 dB, …, 30 = 30 dB, 31 = 31 dB.

Default value of THRESH_E-UTRAN_low_Q = value of THRESH_E‑UTRAN_high_Q.

0-31

5

BCCH D/L

C1_DELTA_MIN

This field gives the minimum value of C1_DELTA, the difference between current and best C1 value (see subclause 6.6.1a) that will trigger measurements for cell reselection. This is also the initial value of C1_DELTA (see subclause 6.6.1a).

0 = 3 dB, 1 = 6 dB, 2 = 9 dB, 3 = 12 dB

Default value = 0 (3 dB).

0-3

2

BCCH D/L

EC-BCCH D/L

C1_DELTA_MAX

This field gives the maximum value of C1_DELTA, the difference between current and best C1 value (see subclause 6.6.1a) that will trigger measurements for cell reselection.

0 = 3 dB, 1 = 6 dB, 2 = 9 dB, 3 = 12 dB, 4 = 15 dB, 5 = 18 dB, 6 = 21 dB, 7 = 24 dB

Default value = 2 (9 dB).

0-7

3

BCCH D/L

EC-BCCH D/L

BT_Threshold_DL

This field indicates the RLA_EC or SLA threshold below which blind physical layer transmissions are used on EC-AGCH. Whether RLA_EC or SLA is used is indicated by the DL_CC_Selection parameter.

If RLA_EC: 0 = -87 dBm, 1 = -88 dBm, …, 30 = -117 dBm, 31 = -118 dBm

If SLA: 0 = 26 dB, 1 = 25 dB, …, 30 = -4 dB, 31 = -5 dB

0-31

5

EC-BCCH D/L

CC2_Range_DL

CC3_Range_DL

These optional fields indicate the RLA_EC or SLA range of downlink CC 2 and 3, respectively. The presence of either one of the fields indicates network support of the associated downlink coverage class.

0 = 1 dB, 1 = 2 dB, …, 30=31 dB, 31 = 32 dB

0-31

5

EC-BCCH D/L

EC_RXLEV_ACCESS_MIN

Minimum received signal level at the MS required for access to the system.

0 = -59 dBm, 1 = -60 dBm, …, 62 = -121 dBm, 63 = -122 dBm

0‑63

6

EC-BCCH D/L

BT_Threshold_UL

This field indicates the estimated BS received signal level threshold below which blind physical layer transmissions are used on EC-RACH.

0 = -90 dBm, 1 = -91 dBm, …, 30 = -120 dBm,31 = -121 dBm

0-31

5

EC-BCCH D/L

CC2_Range_UL

CC3_Range_UL

CC4_Range_UL

These optional fields indicate the estimated BS received signal level range of uplink CC2 and CC3 respectively. The presence of either one of the fields indicates network support of the associated uplink coverage class. The presence of signal level range of uplink CC4 indicates network support of CC5.

0 = 1 dB, 1 = 2 dB, …, 30 = 31 dB, 31 = 32 dB

0-31

5

EC-BCCH D/L

BSPWR

This field indicates the BS output power used on FCCH and EC-SCH bursts.

0 = 0 dBm, 1 = 1 dBm, …, 51 = 51 dBm.

All other values are reserved.

0-51

6

EC-BCCH D/L

BT_Threshold_UL_Margin

This field indicates the indicates the power margin above BT_Threshold_UL used for (EC-)RACH open-loop power control

0 = 0 dB, 1 = 2 dB, …, 7 = 14 dB

Default value = 2 (4 dB).

0-15

3

EC-BCCH D/L

continued

DL_Signal_Strength_Step_Size

This field indicates the step-size in RLA_EC or SLA above BT_Threshold_DL possible to report by the MS in the EC Packet Channel Request message.

0 = 2 dB, 1 = 4 dB, 2 = 6 dB, 3 = 8 dB.

Default value = 1 (4 dB).

0-3

2

EC-BCCH

D/L

CELL_SELECTION_RLA_MARGIN

During cell selection, EC-GSM-IoT capable MS may omit RLA_EC and RLA_GC measurements on RF channels for which the measured RLA_C is more than CELL_SELECTION_RLA_MARGIN dB below the measured RLA_EC or RLA_GC of the selected cell (see subclause 6.2).

0 = 3 dB, 1 = 6 dB, …, 7 = 24 dB.

Default value = 4 (15 dB).

0-7

3

BCCH D/L

EC-BCCH

D/L

DL_CC_Selection

This field indicates the method for selecting the downlink coverage class to be used by the MS.

0 = RLA_EC based coverage class selection

1 = SLA based coverage class selection

0-1

1

EC-BCCH D/L

XX

0

0

Normal (A/Gb mode)

Normal (A/Gb mode)

XX

0

1

Barred (A/Gb mode)

Barred (A/Gb mode)

XX

1

0

Low (A/Gb mode)

Normal (A/Gb mode) (see note 2)

XX

1

1

Low (A/Gb mode)

Normal (A/Gb mode) (see note 2)

00

0

0

Normal (A/Gb mode) (see note 4)

Normal (A/Gb mode) (see note 4)

00

0

1

Barred (A/Gb and Iu modes) (see note 4)

Barred (A/Gb and Iu modes) (see note 4)

00

1

0

Low (A/Gb mode) (see note 4)

Normal (A/Gb mode) (see notes 2 and 4)

00

1

1

Low (A/Gb mode) (see note 4)

Normal (A/Gb mode) (see notes 2 and 4)

01

X

X

Barred (A/Gb and Iu modes) (see note 5)

Barred (A/Gb and Iu modes) (see note 5)

10

X

X

Normal (Iu mode) (see note 6)

Normal (Iu mode) (see note 6)

11

X

X

Normal (Iu mode) (see note 6)

Normal (Iu mode) (see note 6)

00

X

X

Barred (Iu mode) (see note 4)

Barred (Iu mode) (see note 4)

01

X

X

Barred (Iu mode) (see note 5)

Barred (Iu mode) (see note 5)

10

X

X

Normal (Iu mode) (see note 6)

Normal (Iu mode) (see note 6)

11

X

X

Normal (Iu mode) (see note 6)

Normal (Iu mode) (see note 6)

MS_TXPWR_REQUEST

The power level to be used by an

0‑31

5

L1 header

(ordered MS power level)

MS

downlink

MS_TXPWR_CONF.

Indication of the power

0‑31

5

L1 header

(actual MS power level)

level in use by the MS.

uplink

POWER_LEVEL

The power level to be used by an

0‑31

5

HO/assignment

MS on the indicated channel

command

RXLEV_FULL_SERVING_CELL

The RXLEV in the current

0‑63

6

Measurement

serving cell accessed over

results

all TDMA frames

RXLEV_SUB_SERVING_CELL

The RXLEV in the current

0‑63

6

Measurement

serving cell accessed over

results

a subset of TDMA frames

RXQUAL_FULL_SERVING_CELL

The RXQUAL in the current

0‑7

3

Measurement

serving cell, assessed over

results

all TDMA frames.

RXQUAL_SUB_SERVING_CELL

The RXQUAL in the current

0‑7

3

Measurement

serving a cell, assessed over

results

subset of TDMA frames.

DTX_USED

Indicates whether or not the MS

‑

1

Measurement

used DTX during the previous

results

measurement period.

BA_USED

Value of BA_IND for

0/1

1

Measurement

BCCH allocation used

results

3G_BA_USED

Value of 3G_BA_IND for the 3G neighbour cell list and/or E-UTRAN neighbour cell list

0/1

1

Measurement results

SI 23_BA_USED

Value of SI 23_BA_IND for the E-UTRAN neighbour cell list (see note 5)

0/1

1

Measurement results

RXLEV_NCELL_(1‑6)

The RXLEV assessed on BCCH

0‑63

6

Measurement

carrier as indicated

results

in the BCCH Allocation

BCCH_FREQ_NCELL_(1‑6)

The BCCH carrier RF channel

0‑31

5

Measurement

number in NCELL.

results

BSIC_NCELL_(1‑6)

Base station identification

0‑63

6

Measurement

code for NCELL.

results

MULTIBAND_REPORTING

Indication of the number of cells to be reported for each band in multiband operation.

0‑3

2

BCCH D/L

SACCH D/L

SCALE

Indication of the offset, which applies for the reported RXLEV values.

0 = 0 dB, 1 = +10 dB

0-1

1

Enhanced Measurement Report

SCALE_ORD

Indication of the offset, which shall be used for the reported RXLEV values.

0 = +0 dB, 1 = + 10 dB, 2 = automatic

Default value = 0 dB.

0-2

2

SACCH D/L

Qsearch_C

Search for UTRAN FDD cells if signal level below threshold (0-7):
– 98, – 94, … , – 74 dBm,  (always)
or above threshold (8-15):
– 78, – 74, … , – 54 dBm,  (never)

Search for UTRAN TDD cells if signal level below threshold (0-7):
– 98, – 94, … , – 74 dBm,  (always)
or above threshold (8-15):
– 90, – 86, … , -66 dBm,  (never)

0-15

4

SACCH D/L

REPORT_TYPE

Indicates which report type the MS shall use,
0 = enhanced, 1 = normal

Default value = normal

0/1

1

BCCH D/L

SACCH D/L

XXX_MULTIRAT_REPORTING

The number of cells from the access technology/mode XXX (one or more) that shall be included in the list of strongest cells or in the measurement report.

0-3

2

BCCH D/L

SACCH D/L

SERVING_BAND_REPORTING

The number of cells from the GSM serving frequency band that shall be included in the list of strongest cells or in the measurement report.

Default value = 3

0-3

2

BCCH D/L

SACCH D/L

continued

REP_PRIORITY

Indicates the reporting priority per cell,
0 = normal, 1 = high

Default value = normal

0/1

1

SACCH D/L

REPORTING_RATE

Indicates the allowed reporting rate,
0 = normal, 1 = reduced.

Default value = normal.

0/1

1

SACCH D/L

INVALID_BSIC_REPORTING

Indicates if GSM cells with invalid BSIC and allowed NCC part may be reported,

0 = no, 1 = yes.

Default value = no.

0/1

1

SACCH D/L

XXX_REPORTING_THRESHOLD

Apply priority reporting if the reported value is above threshold for GSM frequency band or access technology/mode XXX (one or more),
0, 6, … , 36,  (never).

Default value = always.

0-7

3

BCCH D/L

SACCH D/L

FDD_REPORTING_THRESHOLD_2

Reporting threshold for the CPICH parameter (Ec/No or RSCP) that is not reported according to FDD_REP_QUANT.

Default value = 0 (disabled)

0-63

6

BCCH/D/L

SACCH D/L

XXX_REPORTING_OFFSET

Apply an offset to the reported value when prioritising the cells for reporting for GSM frequency band or access technology/mode XXX (one or more),
0, 6, … , 42.
Default value = 0.

0-7

3

BCCH D/L

SACCH D/L

FDD_REP_QUANT

Indicates the reporting quantity for UTRAN FDD cells,
0 = RSCP, 1 = Ec/No

0/1

1

BCCH D/L

SACCH D/L

RTD

The real time difference to other GSM cells, modulo 51 TDMA frames,
step: 1 or 1/64 TDMA frame

0-50
or
0-3263

6
or
12

SACCH D/L

E-UTRAN_REP_QUANT

Indicates the reporting quantity for
E-UTRAN cells,
0 = RSRP, 1 = RSRQ

0/1

1

BCCH D/L

SACCH D/L

E-UTRAN_FDD_REPORTING_THRESHOLD_2

Reporting threshold for the parameter (RSRP or RSRQ) that is not reported according to
E-UTRAN_REP_QUANT.

Default value = 0 (disabled)

0-63

6

BCCH/D/L

SACCH D/L

E‑UTRAN_TDD_REPORTING_THRESHOLD_2

Reporting threshold for the parameter (RSRP or RSRQ) that is not reported according to
E-UTRAN_REP_QUANT.

Default value = 0 (disabled)

0-63

6

BCCH/D/L

SACCH D/L

E‑UTRAN_FDD_MEASUREMENT_REPORT_OFFSET

Apply measurement reporting if the measured value is above the parameter, which is also used in the calculation of the value of the quantity (RSRP or RSRQ) that is reported according to
E-UTRAN_REP_QUANT, when 3-bit reporting is used.

For RSRP the mapping is as follows:

0 = -140 dBm, 1 = -139 dBm, 2 = -138 dBm, …, 62 = -78 dBm, 63 = -77 dBm.

For RSRQ the mapping is as follows:

0 = -19.5 dB, 1 = -19 dB, 2 = -18.5 dB, …, 31 = -4 dB, 32 = -3.5 dB, 33 = -3 dB.

Default value = 0.

0-63

6

BCCH/D/L

SACCH D/L

E‑UTRAN_TDD_MEASUREMENT_REPORT_OFFSET

Apply measurement reporting if the measured value is above the parameter, which is also used in the calculation of the value of the quantity (RSRP or RSRQ) that is reported according to
E-UTRAN_REP_QUANT, when 3-bit reporting is used.

For RSRP the mapping is as follows:

0 = -140 dBm, 1 = -139 dBm, 2 = -138 dBm, …, 62 = -78 dBm, 63 = -77 dBm.

For RSRQ the mapping is as follows:

0 = -19.5 dB, 1 = -19 dB, 2 = -18.5 dB, …, 31 = -4 dB, 32 = -3.5 dB, 33 = -3 dB.

Default value = 0.

0-63

6

BCCH/D/L

SACCH D/L

REPORTING_GRANULARITY

Signals whether fine or coarse granularity is used in 3-bit reporting.

For RSRP: 0 = 2 dB step size, 1 = 3 dB step size; for RSRQ: 0 = 1 dB step size, 1 = 2 dB step size).

Default value = 0.

0/1

1

BCCH/D/L

SACCH D/L

Qsearch_C_E-UTRAN

Search for E-UTRAN cells if signal level below threshold (0-7):
– 98, – 94, … , – 74 dBm,  (always)
or above threshold (8-15):
– 78, – 74, … , – 54 dBm,  (never)

0-15

4

SACCH D/L

Measurement_Control_E-UTRAN

Frequency-specific search enabled

0 = never search 1 = use Qsearch_C_E-UTRAN if received, otherwise use Qsearch_C_E-UTRAN_Initial,

Default value = 1.

0/1

1

SACCH D/L

Measurement_Control_UTRAN

Frequency-specific search enabled

0 = never search 1 = use Qsearch_C if received, otherwise use Qsearch_C_Initial,

Default value = 1.

0/1

1

SACCH D/L

UTRAN_CSG_FDD_REPORTING_THRESHOLD

Reporting threshold for the reported value (Ec/No) for UTRAN FDD CSG cells,

0, 6, … , 36,  (never).

Default value = same as the value of FDD_REPORTING_THRESHOLD if signalled and if FDD_REP_QUANT = 1; otherwise 4 (-12.5 dB ≤ CPICH Ec/Io <  -12 dB).

0-7

3

BCCH/D/L

SACCH D/L

UTRAN_CSG_FDD_REPORTING_THRESHOLD_2

Reporting threshold for the non-reported value (RSCP) for UTRAN FDD CSG cells,

Default value = same as the value of FDD_REPORTING_THRESHOLD_2 if signalled and if FDD_REP_QUANT = 1; otherwise 6 (‑110 dBm ≤ CPICH RSCP < ‑109 dBm).

0-63

6

BCCH/D/L

SACCH D/L

UTRAN_CSG_TDD_REPORTING_THRESHOLD

Reporting threshold for the reported value (RSCP) for UTRAN TDD CSG cells,

0, 6, … , 36,  (never).

Default value = same as the value of TDD_REPORTING_THRESHOLD if signalled; otherwise 0.

0-7

3

BCCH/D/L

SACCH D/L

E-UTRAN_CSG_FDD_REPORTING_THRESHOLD

Reporting threshold for the reported value (RSRQ) for E-UTRAN FDD CSG cells,

0, 6, … , 36,  (never).

Default value = same as the value of E-UTRAN_FDD_REPORTING_THRESHOLD if signalled and if E-UTRAN_REP_QUANT = 1; otherwise 3 (‑11.0 dB ≤ RSRQ < ‑10.5 dB).

0-7

3

BCCH/D/L

E-UTRAN_CSG_FDD_REPORTING_THRESHOLD_2

Reporting threshold for the non-reported value (RSRP) for E-UTRAN FDD CSG cells.

Default value = same as the value of E-UTRAN_FDD_REPORTING_THRESHOLD_2 if signalled and if E-UTRAN_REP_QUANT = 1; otherwise 11 (‑120 dBm ≤ RSRP < ‑118 dBm).

0-63

6

BCCH/D/L

E-UTRAN_CSG_TDD_REPORTING_THRESHOLD

Reporting threshold for the reported value (RSRQ) for E-UTRAN TDD CSG cells,

0, 6, … , 36,  (never).

Default value = same as the value of E-UTRAN_TDD_REPORTING_THRESHOLD if signalled and if E-UTRAN_REP_QUANT = 1; otherwise 3 (‑11.0 dB ≤ RSRQ < ‑10.5 dB).

0-7

3

BCCH/D/L

E-UTRAN_CSG_TDD_REPORTING_THRESHOLD_2

Reporting threshold for the non-reported value (RSRP) for E-UTRAN TDD CSG cells,

Default value = same as the value of E-UTRAN_TDD_REPORTING_THRESHOLD_2 if signalled and if E-UTRAN_REP_QUANT = 1; otherwise 11 (‑120 dBm ≤ RSRP < ‑118 dBm).

0-63

6

BCCH/D/L

NOTE 1: RXLEV and RXQUAL fields are coded as described in clause 8.

NOTE 2: BCCH_FREQ_NCELL_(1‑6) is coded in accordance with 3GPP TS 44.018 as the position in the list of BA carriers.

NOTE 3: For the details of the Measurement Result message see 3GPP TS 44.018.

NOTE 4: SI 23_BA_IND is applicable when network sharing is supported in a given cell and for a mobile station supporting network sharing, see 3GPP TS 44.018.

NOTE 5: SI 23_BA_USED is related to network sharing, see 3GPP TS 44.018.