R.1 Frequency offset in uplink
3GPP45.005GSM/EDGE Radio transmission and receptionTS
For uplink channels in EC operation when multiple subchannels are assigned different Overlaid CDMA codes an offset in frequency, generated separately for each subchannel, shall be applied according to the Gaussian distribution below
where
– is 30 Hz
– x is the frequency offset
The frequency offset of each subchannel shall be constant within a burst with the same offset applied in all blind physical layer transmissions of each Overlaid CDMA subchannel according to its respective CC and may be selected in an implementation dependent way such that the above probabilities are satisfied.
Annex S (normative):
Normalized coherency error
The normalized RMS (
) is defined as the ratio of the maximum RMS value of the error vector magnitude (
) between any two consecutive bursts 
and 
, from a set of blind physical layer transmissions in the same TDMA frame, compared to the average RMS value over the set of blind physical layer transmissions (
). The normalized RMS is calculated over the useful part of the burst. The normalized coherency error shall be measured after a measurement receive filter at baseband. The specification is based on using the specified, windowed, raised-cosine filter with roll-off 0.25 and single side-band bandwidth of 90 kHz (see subclause 4.6.2).
where
– 
is the sum over the useful part of the burst where N is the number of samples (147 or 148 for EC-PDTCH using CC2 to CC4; and 88 for 2 TS EC-RACH mapping using CC2 to CC4 or CC5 using EDAB format) which shall be taken at the symbol rate
– x and y are indices to any given pair of consecutive bursts out of the blind physical layer transmissions
– M is the number of blind physical layer transmissions per TDMA frame (i.e. M=4 for EC-PDTCH and M=2 for 2 TS EC-RACH mapping or EDAB format)
Before taking the logarithm, the measured average of 
over at least 200 TDMA frames (
) in case M=4 shall be computed. For M=4, the TDMA frames over which the average is computed shall be spread over at least 50 separate FUAs (Fixed Uplink Allocations, see 3GPP TS 44.060 [38]), each with a similar size of the allocation, between which EC-PACCH/D or EC-PACCH/D/2TS is transmitted to the MS.
For M=2, the measured average of over at least 190 TDMA frames () shall be computed. The TDMA frames over which the average is computed shall be spread over at least 6 EC Packet Channel Request messages (see 3GPP TS 44.018 [7]), triggered by a matching paging request. Since the network does not respond to the channel request, it enforces the MS to repeat its EC Packet Channel Request for configured number of maximum retransmissions.
NOTE: For CC4 using 2 TS EC-RACH mapping, 8 EC Packet Paging Requests, with configured EC_Max_Retrans = 7, occupy 192 TDMA frames. For EDAB, 6 EC Packet Paging Requests, with configured EC_Max_Retrans = 5, occupy 396 TDMA frames. For CC2 and CC3 using 2 TS EC-RACH mapping, a higher number of EC Packet Channel Request messages need to be sent to fulfil the above requirement.
Then for M=4 or M=2, the measured average of shall be transferred to dB scale according to
and is referred to as Normalized Coherency Error.
Annex T (normative):
Calculation of the equivalent combined power
For measuring the equivalent combined power of four blind physical layer transmissions per TDMA frame to which the coherency requirement in subclause 4.6.3 applies, the transmit signal is demodulated to a complex-valued baseband signal. The measurement bandwidth shall be at least 300 kHz.
Let Y1(k) denote the complex-valued samples of the useful part of the burst, sampled at the symbol times, from the first burst of blind physical layer transmissions within a TDMA frame. Similarly, Y2(k), Y3(k) and Y4(k) denote the corresponding samples from the second, third and fourth burst of the same blind physical layer transmissions on the subsequent timeslots in the same TDMA frame, respectively.
The equivalent combined signal Z(k) is calculated by summing up the samples of the four bursts’ useful parts without any compensation:
Z(k) = Y1(k) + Y2(k) + Y3(k) + Y4(k)
where
k is the sample number 0 to 147 within the useful part of the burst.
The power of Z(k) is .
The equivalent combined power is the power of Z(k), averaged over the number of TDMA frames measured.
The equivalent combined power shall then be converted to dBm scale.
NOTE: Ideally, the power of Z(k) is 16 times the power of each of Y1(k) to Y4(k).
Annex U (informative):
Change history
|
SPEC |
SMG# |
CR |
REV |
PHASE |
VERS |
NEW_VERS |
SUBJECT |
|---|---|---|---|---|---|---|---|
|
05.05 |
s24 |
A063 |
R97 |
5.6.0 |
6.0.0 |
Reference performance for GPRS |
|
|
05.05 |
s25 |
A067 |
R97 |
6.0.0 |
6.1.0 |
14.4kbps Data Service |
|
|
05.05 |
s26 |
A065 |
R97 |
6.1.0 |
6.2.0 |
Repeater Systems using Frequency Shift |
|
|
05.05 |
s26 |
A071 |
R97 |
6.1.0 |
6.2.0 |
Adjacent time slot rejection performance |
|
|
05.05 |
s26 |
A073 |
R97 |
6.1.0 |
6.2.0 |
Frequency hopping performance under interference conditions |
|
|
05.05 |
s26 |
A074 |
R97 |
6.1.0 |
6.2.0 |
Possibility for operators and manufacturers to define BTS output power |
|
|
05.05 |
s26 |
A075 |
R97 |
6.1.0 |
6.2.0 |
Introducing performance requirement for the 11 bit PRACH |
|
|
05.05 |
s26 |
A045 |
R98 |
6.4.0 |
7.0.0 |
Pico BTS |
|
|
05.05 |
s27 |
A076 |
R97 |
6.2.0 |
6.3.0 |
False USF detection |
|
|
05.05 |
s27 |
A077 |
R97 |
6.2.0 |
6.3.0 |
Power control levels 29-31 for DCS 1800 |
|
|
05.05 |
s27 |
A078 |
R97 |
6.2.0 |
6.3.0 |
DCS 1800 MS sensitivity for GPRS |
|
|
05.05 |
s27 |
A080 |
R97 |
6.2.0 |
6.3.0 |
Correction of reference for MS test loop |
|
|
05.05 |
s28 |
A083 |
R97 |
6.3.0 |
6.4.0 |
Signal level for reference interference measurements in GPRS |
|
|
05.05 |
s28 |
A081 |
R98 |
6.4.0 |
7.0.0 |
BTS performance requirements for Picocells |
|
|
05.05 |
s28 |
A082 |
R98 |
6.4.0 |
7.0.0 |
Harmonization between GSM and PCS 1 900 standard |
|
|
05.05 |
s28 |
A084 |
R98 |
6.4.0 |
7.0.0 |
Introduction of CTS in GSM 05.05 |
|
|
05.05 |
s28 |
A091 |
R98 |
6.4.0 |
7.0.0 |
Transmitter / receiver performance in CTS |
|
|
05.05 |
s29 |
A098 |
R98 |
7.0.0 |
7.1.0 |
Micro BTS: Deletion of Max output power per carrier values expressed in Watts |
|
|
05.05 |
s29 |
A099 |
R98 |
7.0.0 |
7.1.0 |
Correction to pico-BTS interference performance |
|
|
05.05 |
s29 |
A143 |
R98 |
7.0.0 |
7.1.0 |
AMR reference sensitivity and interference |
|
|
05.05 |
s29 |
A100 |
R99 |
7.1.0 |
8.0.0 |
Output level dynamic operation for EDGE |
|
|
05.05 |
s29 |
A102 |
R99 |
7.1.0 |
8.0.0 |
Blocking requirements for EDGE MS and BTS receivers |
|
|
05.05 |
s29 |
A103 |
R99 |
7.1.0 |
8.0.0 |
Power classes for EDGE mobile stations |
|
|
05.05 |
s29 |
A104 |
R99 |
7.1.0 |
8.0.0 |
Modulation Accuracy for EDGE MS and BTS |
|
|
05.05 |
s29 |
A105 |
R99 |
7.1.0 |
8.0.0 |
Spectrum Mask for EDGE MS and BTS |
|
|
05.05 |
s29 |
A106 |
R99 |
7.1.0 |
8.0.0 |
High input level requirements for EDGE receivers |
|
|
05.05 |
s29 |
A107 |
R99 |
7.1.0 |
8.0.0 |
Introduction of LCS – Requirements on Location Measurement Unit |
|
|
05.05 |
s29 |
A108 |
R99 |
7.1.0 |
8.0.0 |
Output power for EDGE BTS |
|
|
05.05 |
s29 |
A111 |
R99 |
7.1.0 |
8.0.0 |
GSM 400 systems introduced in GSM 05.05 |
|
|
05.05 |
s30 |
A114 |
R99 |
8.0.0 |
8.1.0 |
Output level Dynamic operation in EDGE |
|
|
05.05 |
s30 |
A115 |
R99 |
8.0.0 |
8.1.0 |
EDGE blocking requirement for micro and pico-BTS |
|
|
05.05 |
s30 |
A116 |
R99 |
8.0.0 |
8.1.0 |
850 MHz frequency band and channel arrangement |
|
|
05.05 |
s30 |
A117 |
R99 |
8.0.0 |
8.1.0 |
EDGE 850 MHz and 1900 MHz mixed mode |
|
|
05.05 |
s30 |
A118 |
R99 |
8.0.0 |
8.1.0 |
Frequency compensation requirements for EDGE receivers |
|
|
05.05 |
s30 |
A119 |
R99 |
8.0.0 |
8.1.0 |
Modulation accuracy for EDGE MS and BTS |
|
|
05.05 |
s30 |
A120 |
R99 |
8.0.0 |
8.1.0 |
AMR reference sensitivity and interference |
|
|
05.05 |
s30 |
A124 |
R99 |
8.0.0 |
8.1.0 |
Introduction of RATSCCH for AMR |
|
|
05.05 |
s30 |
A126 |
R99 |
8.0.0 |
8.1.0 |
8-PSK requirements for GSM 400 |
|
|
05.05 |
s30 |
A127 |
R99 |
8.0.0 |
8.1.0 |
PCS 1900 MHz intermodulation requirements |
|
|
05.05 |
s30 |
A129 |
R99 |
8.0.0 |
8.1.0 |
Allowed power level between two consecutive active time slots |
|
|
05.05 |
s30 |
A159 |
R99 |
8.0.0 |
8.1.0 |
GSM in the 400 MHz bands: editorial modification |
|
|
05.05 |
s30b |
A132 |
R99 |
8.1.0 |
8.2.0 |
EDGE blocking requirement for micro and pico-BTS |
|
|
05.05 |
s30b |
A133 |
R99 |
8.1.0 |
8.2.0 |
Spurious emission in RX- and TX-band in other frequency bands |
|
|
05.05 |
S31 |
A101 |
R99 |
8.2.0 |
8.3.0 |
Transmitter/receiver performance for EDGE |
|
|
05.05 |
S31 |
A134 |
R99 |
8.2.0 |
8.3.0 |
Measurement Filter for EDGE EVM |
|
|
05.05 |
S31 |
A135 |
R99 |
8.2.0 |
8.3.0 |
Alignment of Measurement Filter reference |
|
|
05.05 |
S31 |
A136 |
R99 |
8.2.0 |
8.3.0 |
Clarification of Intra BTS Intermodulation Attenuation requirements for MXM 850 and MXM 1900 BTS |
|
|
05.05 |
S31 |
A137 |
R99 |
8.2.0 |
8.3.0 |
Clarification of Intra BTS Intermodulation Attenuation requirements for PCS 1900 BTS |
|
|
05.05 |
S31 |
A138 |
R99 |
8.2.0 |
8.3.0 |
Definition of MS for Mixed-mode network |
|
|
05.05 |
S31 |
A139 |
R99 |
8.2.0 |
8.3.0 |
Correction to Output level dynamic operation |
|
|
05.05 |
S31 |
A141 |
R99 |
8.2.0 |
8.3.0 |
Nominal Error Rate performance for EDGE |
|
|
05.05 |
S31 |
A142 |
R99 |
8.2.0 |
8.3.0 |
Corrections to receiver Characteristics for EDGE |
|
|
05.05 |
S31 |
A143 |
R99 |
8.2.0 |
8.3.0 |
Spurious emission measurement bandwidths updated to include GSM 400 systems |
|
|
05.05 |
S31 |
A144 |
R99 |
8.2.0 |
8.3.0 |
Harmonization of Transmitter/receiver performance requirements for PCS 1900 |
|
|
05.05 |
S31 |
A147 |
R99 |
8.2.0 |
8.3.0 |
Relaxation of C/I performance requirement for CS4 |
|
|
05.05 |
S31 |
A149 |
R99 |
8.2.0 |
8.3.0 |
EVM requirements for EDGE BTS transmitter with combining equipment |
|
|
05.05 |
S31 |
A150 |
R99 |
8.2.0 |
8.3.0 |
Introduction of Incremental Redundancy Receiver Performance for MS |
|
|
05.05 |
S31 |
A151 |
R99 |
8.2.0 |
8.3.0 |
Switching Transients for 8-PSK Modulation |
|
|
05.05 |
S31 |
A237 |
R99 |
8.2.0 |
8.3.0 |
RF Requirements for TOA LMU |
|
|
05.05 |
S31 |
A239 |
R99 |
8.2.0 |
8.3.0 |
Requirements on E-OTD LMU and E-OTD MS |
|
|
05.05 |
S31b |
A247 |
R99 |
8.3.0 |
8.4.0 |
Conforming requirements for LMUs containing a control mobile station |
|
|
05.05 |
S31b |
A154 |
R99 |
8.3.0 |
8.4.0 |
Completion of 3GPP TS 45.005 for EDGE and clean-up |
|
|
05.05 |
S32 |
A157 |
R99 |
8.4.0 |
8.5.0 |
Removal of duplicated figures |
|
|
05.05 |
S32 |
A160 |
R99 |
8.4.0 |
8.5.0 |
Alignment of spurious emissions GSM-3G (UTRA): BTS |
|
|
05.05 |
S32 |
A161 |
R99 |
8.4.0 |
8.5.0 |
Alignment of spurious emissions GSM-3G (UTRA): MS |
|
|
September 2000 – TSG-GERAN#1 |
|||||||
|
05.05 |
G01 |
A162 |
R99 |
8.5.0 |
8.6.0 |
Pico BTS Reference interference level clarification |
|
|
05.05 |
G01 |
A163 |
R99 |
8.5.0 |
8.6.0 |
Alignment of spurious emissions GSM-3G(UTRA): BTS |
|
|
05.05 |
G01 |
A164 |
R99 |
8.5.0 |
8.6.0 |
Alignment of spurious emissions GSM-3G(UTRA): MS |
|
|
05.05 |
G01 |
A168 |
1 |
R99 |
8.5.0 |
8.6.0 |
Definition of "small MS" |
|
05.05 |
G01 |
A172 |
R99 |
8.5.0 |
8.6.0 |
CR 05.05-A172 Correction on CS-4 performance requirements |
|
|
05.05 |
G01 |
A173 |
1 |
R99 |
8.5.0 |
8.6.0 |
Clarification of BTS output power capability with 8-PSK |
|
September 2000 – TSG-GERAN#1 Release 4 |
|||||||
|
05.05 |
G01 |
A165 |
1 |
Release 4 |
8.6.0 |
4.0.0 |
Introduction of GSM 700 in 05.05 GSM on 700 MHz Frequency Band |
|
4.0.0 |
4.0.1 |
Oct 2000: Correction to references. |
|||||
|
November 2000 – TSG-GERAN#2 Release 4 |
|||||||
|
45.005 |
G02 |
001 |
2 |
Release 4 |
4.0.1 |
4.1.0 |
NER requirements for EGPRS |
|
45.005 |
G02 |
002 |
1 |
Release 4 |
4.0.1 |
4.1.0 |
Tolerance of BTS output power levels |
|
45.005 |
G02 |
003 |
Release 4 |
4.0.1 |
4.1.0 |
Alignment of AM suppression requirements for PCS 1900 MS |
|
|
45.005 |
G02 |
004 |
1 |
Release 4 |
4.0.1 |
4.1.0 |
Testing of Blocking requirements for MXM 1900 BSS |
|
45.005 |
G02 |
005 |
Release 4 |
4.0.1 |
4.1.0 |
Testing of Intra BSS intermodulation attenuation requirements for MXM 1900 BSS |
|
|
4.1.0 |
4.1.1 |
Front page layout correction |
|||||
|
January 2001 – TSG-GERAN#3 Release 4 |
|||||||
|
45.005 |
G03 |
010 |
Release 4 |
4.1.1 |
4.2.0 |
Correction of Power vs Time mask for 8-PSK |
|
|
45.005 |
G03 |
011 |
1 |
Release 4 |
4.1.1 |
4.2.0 |
Definition of MXM systems missing |
|
45.005 |
G03 |
012 |
Release 4 |
4.1.1 |
4.2.0 |
Testing of Intra BSS intermodulation attenuation requirements for MXM 850 BSS |
|
|
45.005 |
G03 |
013 |
Release 4 |
4.1.1 |
4.2.0 |
Alignment of AM suppression requirements for MXM 1900 BTS with PCS 1900 BTS and MXM 850 BTS with GSM 850 BTS |
|
|
45.005 |
G03 |
014 |
Release 4 |
4.1.1 |
4.2.0 |
Mixed-Mode Systems Intermodulation Attenuation |
|
|
45.005 |
G03 |
015 |
1 |
Release 4 |
4.1.1 |
4.2.0 |
Interpretation of common DCS 1800 / PCS 1900 ARFCN numbers when transmitted on other bands |
|
April 2001 – TSG-GERAN#4 Release 4 |
|||||||
|
45.005 |
G04 |
016 |
1 |
Release 4 |
4.2.0 |
4.3.0 |
Clarification of Origin Offset Suppression requirements |
|
45.005 |
G04 |
017 |
3 |
Release 4 |
4.2.0 |
4.3.0 |
Dynamic ARFCN mapping |
|
45.005 |
G04 |
018 |
1 |
Release 4 |
4.2.0 |
4.3.0 |
Corrections to facilitate the interpretation |
|
45.005 |
G04 |
019 |
Release 4 |
4.2.0 |
4.3.0 |
Removal of requirements valid before December 1999 |
|
|
45.005 |
G04 |
020 |
Release 4 |
4.2.0 |
4.3.0 |
Removal of requirements for Intermodulation between MS |
|
|
June 2001 – TSG-GERAN#4 Release 4 |
|||||||
|
45.005 |
G05 |
021 |
Release 4 |
4.3.0 |
4.4.0 |
Corrections for clarification regarding output power and blocking requirements |
|
|
June 2001 – TSG-GERAN#4 Release 5 |
|
Change history |
|||||||
|
Date |
TSG # |
TSG Doc. |
CR |
Rev |
Subject/Comment |
Old |
New |
|
2001-06 |
05 |
GP-011259 |
022 |
Introduction of requirements for Wideband AMR FR GMSK modulated speech channels |
4.4.0 |
5.0.0 |
|
|
2001-08 |
06 |
GP-011910 |
024 |
1 |
Correction to 45.005 – Incorrect references in section H.2.2.2 |
5.0.0 |
5.1.0 |
|
2001-08 |
06 |
GP-011537 |
026 |
Corrections for clarification regarding GSM 700 MS, GSM 850 MS and PCS 1900 MS requirements on spurious emissions |
5.0.0 |
5.1.0 |
|
|
2001-08 |
06 |
GP-011944 |
031 |
Alignment to 44.018 for the definition of the BAND_INDICATOR field |
5.0.0 |
5.1.0 |
|
|
2001-11 |
07 |
GP-012747 |
007 |
3 |
Introduction of requirements for adaptive half rate speech channels with 8-PSK modulation |
5.1.0 |
5.2.0 |
|
2001-11 |
07 |
GP-012773 |
036 |
1 |
Correction of references to relevant 3GPP TSs |
5.1.0 |
5.2.0 |
|
2001-11 |
07 |
GP-012777 |
037 |
Correction to wideband AMR receiver performance tables |
5.1.0 |
5.2.0 |
|
|
2002-04 |
09 |
GP-021155 |
041 |
1 |
Correction of AMR FR inband performance requirement |
5.2.0 |
5.3.0 |
|
2002-04 |
09 |
GP-021170 |
042 |
1 |
Alignment of number of codecs for WB-AMR to proposed set |
5.2.0 |
5.3.0 |
|
2002-06 |
10 |
GP-021401 |
043 |
Introduction of AMR-WB 8PSK |
5.3.0 |
5.4.0 |
|
|
2002-06 |
10 |
GP-021958 |
044 |
1 |
Introduction of TCH/WFS receiver performance requirements |
5.3.0 |
5.4.0 |
|
2002-06 |
10 |
GP-021403 |
045 |
Introduction of O-TCH/AHS receiver performance requirements |
5.3.0 |
5.4.0 |
|
|
2002-06 |
10 |
GP-021404 |
046 |
Introduction of O-TCH/WFS receiver performance requirements |
5.3.0 |
5.4.0 |
|
|
2002-06 |
10 |
GP-021405 |
047 |
Introduction of O-TCH/WHS receiver performance requirements |
5.3.0 |
5.4.0 |
|
|
2002-06 |
10 |
GP-022023 |
048 |
1 |
Introduction of O-FACCH receiver performance requirements |
5.3.0 |
5.4.0 |
|
2002-06 |
10 |
GP-021412 |
049 |
Editorial clean up of references |
5.3.0 |
5.4.0 |
|
|
2002-06 |
10 |
GP-022031 |
054 |
AMR AHS7.4 static channel performance correction |
5.3.0 |
5.4.0 |
|
|
2002-08 |
11 |
GP-022468 |
056 |
Correction to TCH/WFS receiver performance requirements |
5.4.0 |
5.5.0 |
|
|
2002-08 |
11 |
GP-022530 |
057 |
Correction to O-TCH/WHS receiver performance requirements |
5.4.0 |
5.5.0 |
|
|
2002-11 |
12 |
GP-023075 |
061 |
Correction of performance requirements for O-TCH/WFS |
5.5.0 |
5.6.0 |
|
|
2002-11 |
12 |
GP-023076 |
062 |
Correction of performance requirements for O-TCH/WHS |
5.5.0 |
5.6.0 |
|
|
2002-11 |
12 |
GP-023077 |
063 |
Correction of performance requirements for O-TCH/AHS |
5.5.0 |
5.6.0 |
|
|
2002-11 |
12 |
GP-023078 |
064 |
Correction of performance requirements for TCH/WFS |
5.5.0 |
5.6.0 |
|
|
2002-11 |
12 |
GP-023079 |
065 |
Correction of performance requirements for O-FACCH channels |
5.5.0 |
5.6.0 |
|
|
2002-11 |
12 |
GP-023080 |
066 |
Correction to reference performance for AMR Rel5 |
5.5.0 |
5.6.0 |
|
|
Release 6 |
|||||||
|
2002-11 |
12 |
GP-023319 |
052 |
2 |
Implementation of new frequency ranges |
5.6.0 |
6.0.0 |
|
2002-11 |
12 |
GP-023422 |
060 |
1 |
Correction of antenna Feeder loss compensator requirements |
5.6.0 |
6.0.0 |
|
2003-02 |
13 |
GP-030150 |
059 |
2 |
Rice doppler spectrum definition |
6.0.0 |
6.1.0 |
|
2003-02 |
13 |
GP-030283 |
069 |
Correction to abbr. in reference interference performance requirements |
6.0.0 |
6.1.0 |
|
|
2003-04 |
14 |
GP-030720 |
071 |
Correction of static AMR sensitivity requirements for TCH/AHS |
6.1.0 |
6.2.0 |
|
|
2003-04 |
14 |
GP-030867 |
074 |
Correction of transmitted power level versus time |
6.1.0 |
6.2.0 |
|
|
2003-08 |
16 |
GP-032232 |
078 |
1 |
Introduction of mobile station multislot power classes |
6.2.0 |
6.3.0 |
|
2004-02 |
18 |
GP-040487 |
080 |
1 |
Flexible Layer One |
6.3.0 |
6.4.0 |
|
2004-04 |
19 |
GP-040875 |
084 |
Correction to transmitted power level vs. time mask |
6.4.0 |
6.5.0 |
|
|
2004-04 |
19 |
GP-041055 |
085 |
Input signal level for interference performance for FLO |
6.4.0 |
6.5.0 |
|
|
2004-06 |
20 |
GP-041698 |
087 |
Inband signalling bits for reference TFCs |
6.5.0 |
6.6.0 |
|
|
2004-11 |
22 |
GP-042829 |
092 |
2 |
Introduction of DARP performance requirements |
6.6.0 |
6.7.0 |
|
2004-11 |
22 |
GP-042753 |
093 |
1 |
Maximum output power when the MS transmits on more slots than assigned for the uplink |
6.6.0 |
6.7.0 |
|
2004-11 |
22 |
GP-042592 |
094 |
FLO performance requirements |
6.6.0 |
6.7.0 |
|
|
2004-11 |
22 |
GP-042857 |
097 |
Removal of PTM-M |
6.6.0 |
6.7.0 |
|
|
2005-01 |
23 |
GP-050041 |
098 |
Table 1i non-existent |
6.7.0 |
6.8.0 |
|
|
2005-01 |
23 |
GP-050145 |
100 |
Removal of a restriction to support full power on two slots on 1800/1900 frequency bands, for certain multiband terminal designs |
6.7.0 |
6.8.0 |
|
|
2005-01 |
23 |
GP-050192 |
101 |
DARP – removal of brackets plus one clarification |
6.7.0 |
6.8.0 |
|
|
2005-04 |
24 |
GP-050906 |
102 |
3 |
Performance requirements for Repeated FACCH |
6.8.0 |
6.9.0 |
|
2005-04 |
24 |
GP-051060 |
105 |
1 |
GSM 750 corrections |
6.8.0 |
6.9.0 |
|
2005-04 |
24 |
GP-051053 |
107 |
1 |
Performance requirements for E-TCH/F32.0 |
6.8.0 |
6.9.0 |
|
2005-04 |
24 |
GP-050974 |
108 |
Clarification on the wanted signal level for adjacent channel performance |
6.8.0 |
6.9.0 |
|
|
2005-04 |
24 |
GP-051061 |
106 |
1 |
Introduction of GSM 710 |
6.9.0 |
7.0.0 |
|
2005-06 |
25 |
GP-051283 |
114 |
Addition of new frequency band (e.g. T-GSM810) to the repeater annex E |
7.0.0 |
7.1.0 |
|
|
2005-06 |
25 |
GP-051766 |
115 |
2 |
Introduction of T-GSM 810 frequency band |
7.0.0 |
7.1.0 |
|
2005-06 |
25 |
GP-051472 |
116 |
Reduced interslot MS output power dynamic range on a multislot configuration |
7.0.0 |
7.1.0 |
|
|
2005-06 |
25 |
GP-051717 |
122 |
1 |
Performance requirements for Repeated Downlink FACCH |
7.0.0 |
7.1.0 |
|
2005-09 |
26 |
GP-051981 |
0123 |
Correction and alignment for PCS 1900 MS power mask |
7.1.0 |
7.2.0 |
|
|
2005-09 |
26 |
GP-052024 |
0127 |
Removal of RATSCCH Identification Requirement |
7.1.0 |
7.2.0 |
|
|
2005-09 |
26 |
GP-052050 |
0129 |
Corrections and clarifications for Repeated Downlink FACCH |
7.1.0 |
7.2.0 |
|
|
2005-11 |
27 |
GP-052671 |
0120 |
2 |
Performance requirements for E-TCH/F32.0 |
7.2.0 |
7.3.0 |
|
2005-11 |
27 |
GP-052673 |
0131 |
1 |
Performance requirements for FLO |
7.2.0 |
7.3.0 |
|
2005-11 |
27 |
GP-052606 |
0133 |
Repeated SACCH performance requirements |
7.2.0 |
7.3.0 |
|
|
2006-01 |
28 |
GP-060325 |
0135 |
1 |
Repeated SACCH performance requirements |
7.3.0 |
7.4.0 |
|
2006-01 |
28 |
GP-060327 |
0137 |
1 |
Repeated Downlink FACCH/H |
7.3.0 |
7.4.0 |
|
2006-04 |
29 |
GP-060713 |
0139 |
Repeated SACCH performance – removal of brackets |
7.4.0 |
7.5.0 |
|
|
2006-04 |
29 |
GP-060923 |
0140 |
1 |
Editorial correction of frequency range |
7.4.0 |
7.5.0 |
|
2006-06 |
30 |
GP-061111 |
0141 |
Correction of terminology: ‘allocation’ vs. ‘assignment’ |
7.5.0 |
7.6.0 |
|
|
2006-06 |
30 |
GP-061475 |
0142 |
2 |
A-GPS Minimum Performance specification baseline |
7.5.0 |
7.6.0 |
|
2006-09 |
31 |
GP-061653 |
0144 |
Correction of undefined or wrong references |
7.6.0 |
7.7.0 |
|
|
2006-11 |
32 |
GP-062452 |
0147 |
1 |
Introduction of performance requirements for DARP phase II (MSRD) |
7.7.0 |
7.8.0 |
|
2007-02 |
33 |
GP-070110 |
0149 |
Max Response Time defined for A-GPS Minimum Performance requirements |
7.8.0 |
7.9.0 |
|
|
2007-02 |
33 |
GP-070111 |
0150 |
Clarifications to A-GPS Minimum Performance requirements |
7.8.0 |
7.9.0 |
|
|
2007-02 |
33 |
GP-070159 |
0151 |
Performance requirements for DARP phase II (MSRD) – Removal of brackets |
7.8.0 |
7.9.0 |
|
|
2007-02 |
33 |
GP-070367 |
0152 |
1 |
Guard period handling option in an exceptional GPRS case |
7.8.0 |
7.9.0 |
|
2007-05 |
34 |
GP-071008 |
0155 |
1 |
MSRD (DARP Phase II) requirements in Downlink Dual Carrier Configurations |
7.9.0 |
7.10.0 |
|
2007-08 |
35 |
GP-071204 |
0154 |
2 |
Correction to extreme condition voltages for Lithium batteries in table D.2.2 |
7.10.0 |
7.11.0 |
|
2007-08 |
35 |
GP-071205 |
0156 |
Correction for multislot power versus time mask |
7.10.0 |
7.11.0 |
|
|
2007-08 |
35 |
GP-071545 |
0157 |
2 |
Introduction of requirements for REDHOT, HUGE and LATRED |
7.10.0 |
7.11.0 |
|
2007-11 |
36 |
GP-071957 |
0158 |
1 |
Time masks for EGPRS2 |
7.11.0 |
7.12.0 |
|
2007-11 |
36 |
GP-071959 |
0159 |
1 |
Clarifications and minor corrections for EGPRS2 |
7.11.0 |
7.12.0 |
|
2007-11 |
36 |
GP-071892 |
0160 |
2 |
MS Antenna Performance Requirements |
7.11.0 |
7.12.0 |
|
2007-11 |
36 |
GP-071969 |
0162 |
Performance requirements for DARP phase I & II – Support of GSM 400 and 700 bands |
7.11.0 |
7.12.0 |
|
|
2008-02 |
37 |
GP-080363 |
0163 |
1 |
Correction of requirement tables for EGPRS2 and RTTI |
7.12.0 |
7.13.0 |
|
2008-02 |
37 |
GP-080120 |
0166 |
Correction of IBSS requirements for GSM 700, GSM 850 and PCS 1900 |
7.12.0 |
7.13.0 |
|
|
2008-02 |
37 |
GP-080292 |
0167 |
EVM measurement filter for higher symbol rate |
7.12.0 |
7.13.0 |
|
|
2008-02 |
37 |
GP-080394 |
0161 |
4 |
Introduction of a new multicarrier BTS class |
7.13.0 |
8.0.0 |
|
2008-05 |
38 |
GP-080500 |
0170 |
Miscellaneous corrections |
8.0.0 |
8.1.0 |
|
|
2008-05 |
38 |
GP-080503 |
0172 |
Output power definition |
8.0.0 |
8.1.0 |
|
|
2008-05 |
38 |
GP-080779 |
0174 |
1 |
Spectrum due to modulation of the wide bandwidth pulse shape |
8.0.0 |
8.1.0 |
|
2008-05 |
38 |
GP-080621 |
0178 |
Removal of correction tables for performance requirement for LATRED |
8.0.0 |
8.1.0 |
|
|
2008-05 |
38 |
GP-080625 |
0180 |
Power vs Time Masks for EGPRS2-B |
8.0.0 |
8.1.0 |
|
|
2008-05 |
38 |
GP-080929 |
0183 |
2 |
Corrections and clarifications to multicarrier BTS class |
8.0.0 |
8.1.0 |
|
2008-08 |
39 |
GP-081318 |
0176 |
2 |
EVM for EGPRS2 DL |
8.1.0 |
8.2.0 |
|
2008-08 |
39 |
GP-081320 |
0182 |
3 |
Proposal for some receiver performance values |
8.1.0 |
8.2.0 |
|
2008-08 |
39 |
GP-081268 |
0190 |
1 |
Correction of reference interference performance for DARP phase II MS on a Downlink Dual Carrier configuration |
8.1.0 |
8.2.0 |
|
2008-08 |
39 |
GP-081380 |
0191 |
1 |
Addition of requirements new frequency bands for co-existence and co-siting |
8.1.0 |
8.2.0 |
|
2008-08 |
39 |
GP-081416 |
0193 |
2 |
Aligning GSM 700 frequencies usage with other 3GPP technologies |
8.1.0 |
8.2.0 |
|
2008-08 |
39 |
GP-081426 |
0194 |
3 |
Clarifications of requirements for multicarrier BTS class 1 and 2 |
8.1.0 |
8.2.0 |
|
2008-11 |
40 |
GP-081588 |
0188 |
2 |
Mixed modulation USF |
8.2.0 |
8.3.0 |
|
2008-11 |
40 |
GP-081796 |
0196 |
1 |
EVM for EGPRS2 DL |
8.2.0 |
8.3.0 |
|
2008-11 |
40 |
GP-081591 |
0198 |
Clarification for Interfererence ratio for adjacent channel requirements |
8.2.0 |
8.3.0 |
|
|
2008-11 |
40 |
GP-081595 |
0200 |
Reference performance for EGPRS2 |
8.2.0 |
8.3.0 |
|
|
2008-11 |
40 |
GP-081903 |
0202 |
2 |
Reference Performance for LATRED |
8.2.0 |
8.3.0 |
|
2008-11 |
40 |
GP-081883 |
0203 |
2 |
Corrections to MCBTS requirements |
8.2.0 |
8.3.0 |
|
2008-11 |
40 |
GP-081881 |
0204 |
2 |
Wideband noise lower limit in MC-BTS |
8.2.0 |
8.3.0 |
|
2008-11 |
40 |
GP-081886 |
0207 |
Correction of MS requirements for spurious emission in 700 MHz band |
8.2.0 |
8.3.0 |
|
|
2009-02 |
41 |
GP-090306 |
0210 |
1 |
Enhancement of readability of multicarrier spectral requirements |
8.3.0 |
8.4.0 |
|
2009-02 |
41 |
GP-090438 |
0211 |
1 |
Introduction of multicarrier BTS class for GSM 700, GSM 850 and PCS 1900 |
8.3.0 |
8.4.0 |
|
2009-02 |
41 |
GP-090418 |
0212 |
1 |
Correction of requirements for Nominal Error Rate at higher order modulations |
8.3.0 |
8.4.0 |
|
2009-02 |
41 |
GP-090208 |
0214 |
Correction of frequency range for GSM 700 regarding blocking requirements |
8.3.0 |
8.4.0 |
|
|
2009-02 |
41 |
GP-090441 |
0215 |
1 |
Correction of absolute limit for IM products from multicarrier BTS |
8.3.0 |
8.4.0 |
|
2009-02 |
41 |
GP-090417 |
0217 |
1 |
Reference Performance for EGPRS2, Sensitivity |
8.3.0 |
8.4.0 |
|
2009-02 |
41 |
GP-090220 |
0219 |
Reference Performance for EGPRS2, Co-Channel interference |
8.3.0 |
8.4.0 |
|
|
2009-02 |
41 |
GP-090430 |
0221 |
1 |
Reference Performance for EGPRS2, Adjacent-Channel interference |
8.3.0 |
8.4.0 |
|
2009-02 |
41 |
GP-090230 |
0223 |
EVM for EGPRS2-B DL |
8.3.0 |
8.4.0 |
|
|
2009-02 |
41 |
GP-090433 |
0224 |
1 |
Clarification of exceptions for MCBTS regarding Spectrum due to modulation and wideband noise |
8.3.0 |
8.4.0 |
|
2009-02 |
41 |
GP-090537 |
0226 |
3 |
Alignment of Power Level in Nominal Error Rate Measurement with GMSK Modulation to the Relaxed Blocking Values of GSM 400, T-GSM 810 and E-GSM 900 |
8.3.0 |
8.4.0 |
|
2009-05 |
42 |
GP-090968 |
0229 |
1 |
Introduction of EVM requirement for EGPRS2 for Repeater |
8.4.0 |
8.5.0 |
|
2009-05 |
42 |
GP-090667 |
0232 |
Addition of EGPRS2 DL Performance Requirements for MSRD Capable Mobiles |
8.4.0 |
8.5.0 |
|
|
2009-05 |
42 |
GP-090693 |
0235 |
EVM for EGPRS2-A, UL |
8.4.0 |
8.5.0 |
|
|
2009-05 |
42 |
GP-090977 |
0239 |
2 |
Introduction of MCS-0 |
8.4.0 |
8.5.0 |
|
2009-05 |
42 |
GP-091041 |
0242 |
3 |
Reference performance EGPRS2-A, DL, Adjacent channel interference |
8.4.0 |
8.5.0 |
|
2009-05 |
42 |
GP-090827 |
0246 |
1 |
Reference performance EGPRS2-A, UL, Co-channel and Adjacent channel interference |
8.4.0 |
8.5.0 |
|
2009-05 |
42 |
GP-091045 |
0249 |
2 |
Clarifications of requirements for Spectrum due to modulation for MCBTS at frequency offset below 1.8 MHz |
8.4.0 |
8.5.0 |
|
2009-05 |
42 |
GP-090722 |
0251 |
Clarifications of requirements for Spectrum due to switching transients for MCBTS |
8.4.0 |
8.5.0 |
|
|
2009-05 |
42 |
GP-090995 |
0252 |
1 |
Alignment of requirements for Nominal Error Rate (NER) and RACH performance with blocking requirements for MCBTS in lower frequency bands |
8.4.0 |
8.5.0 |
|
2009-05 |
42 |
GP-090997 |
0253 |
1 |
Correction of absolute limit for IM products and related clarifications for multicarrier BTS |
8.4.0 |
8.5.0 |
|
2009-05 |
42 |
GP-090897 |
0255 |
1 |
Reference performance EGPRS2-B, DL, Sensitivity and Co-channel performance |
8.4.0 |
8.5.0 |
|
2009-05 |
42 |
GP-090881 |
0257 |
Reference performance EGPRS2, UL, Sensitivity |
8.4.0 |
8.5.0 |
|
|
2009-05 |
42 |
GP-090985 |
0259 |
Improvement of alignment between spurious emissions of MCBTS Classes 1 and 2 |
8.4.0 |
8.5.0 |
|
|
2009-09 |
43 |
GP-091253 |
0237 |
3 |
Spectrum due to modulation and wide band noise, narrow pulse EGPRS2-B |
8.5.0 |
8.6.0 |
|
2009-09 |
43 |
GP-091257 |
0244 |
1 |
Reference performance EGPRS2-A, 400 kHz Adjacent channel interference |
8.5.0 |
8.6.0 |
|
2009-09 |
43 |
GP-091132 |
0262 |
Introduction of EVM requirement for EGPRS2 for Repeater |
8.5.0 |
8.6.0 |
|
|
2009-09 |
43 |
GP-091269 |
0269 |
Relaxation of reference performance EGPRS2-A, DL, Co-channel and Adj-channel |
8.5.0 |
8.6.0 |
|
|
2009-09 |
43 |
GP-091275 |
0273 |
Reference performance EGPRS2-B, Sensitivity and Reduced Latency |
8.5.0 |
8.6.0 |
|
|
2009-09 |
43 |
GP-091281 |
0277 |
Reference performance EGPRS2-B, UL, Co-channel |
8.5.0 |
8.6.0 |
|
|
2009-09 |
43 |
GP-091674 |
0281 |
2 |
Reference performance EGPRS2-B, UL, Adj-channel |
8.5.0 |
8.6.0 |
|
2009-09 |
43 |
GP-091296 |
0286 |
Removal of brackets, RMS EVM, EGPRS2, Base station |
8.5.0 |
8.6.0 |
|
|
2009-09 |
43 |
GP-091302 |
0288 |
Removal of brackets: NER, Adj-ch signal levels and Pico-BTS requirements for EGPRS2 |
8.5.0 |
8.6.0 |
|
|
2009-09 |
43 |
GP-091567 |
0289 |
1 |
Correction of lower frequency offset limit for exceptions in requirements for Spectrum due to modulation and wide band noise for MCBTS |
8.5.0 |
8.6.0 |
|
2009-09 |
43 |
GP-091322 |
0294 |
Removal T-GSM 900 |
8.5.0 |
8.6.0 |
|
|
2009-09 |
43 |
GP-091323 |
0295 |
Introduction of requirements for protection of services in the new frequency bands 1880-1920 MHz and 2300-2400 MHz available for 3GPP access technologies |
8.5.0 |
8.6.0 |
|
|
2009-09 |
43 |
GP-091740 |
0297 |
2 |
Reference performance EGPRS2-B, DL, Sensitivity (updates and additions) |
8.5.0 |
8.6.0 |
|
2009-09 |
43 |
GP-091331 |
0299 |
Reference performance EGPRS2-B, DL, Co-channel (updates and additions) |
8.5.0 |
8.6.0 |
|
|
2009-09 |
43 |
GP-091736 |
0301 |
2 |
Introduction of MCBTS capability for operating split frequency allocation |
8.5.0 |
8.6.0 |
|
2009-09 |
43 |
GP-091664 |
0305 |
Removal of blocking, IM characteristics and AM suppression receiver requirements for QPSK, 16QAM and 32QAM modulations introduced in EGPRS2 |
8.5.0 |
8.6.0 |
|
|
2009-09 |
43 |
GP-091585 |
0290 |
1 |
Introduction of Minimum receiver performance for multicarrier BTS declared as Multi-standard capable base station (MSR BS) |
8.6.0 |
9.0.0 |
|
2009-09 |
43 |
GP-091771 |
0303 |
3 |
Restructuring TS 45.005 to facilitate referencing to relevant Single RAT requirements from MSR BS TS |
8.6.0 |
9.0.0 |
|
2009-09 |
43 |
GP-091682 |
0306 |
Additional GANSS Minimum Performance requirements |
8.6.0 |
9.0.0 |
|
|
2009-11 |
44 |
GP-092127 |
284 |
2 |
Single Antenna Requirements for EGPRS2-B, UL |
9.0.0 |
9.1.0 |
|
2009-11 |
44 |
GP-091965 |
0307 |
3 |
Removal of Brackets, EGPRS2-A UL |
9.0.0 |
9.1.0 |
|
2009-11 |
44 |
GP-092190 |
0310 |
4 |
Removal of Brackets, EGPRS2-B UL |
9.0.0 |
9.1.0 |
|
2009-11 |
44 |
GP-091991 |
0314 |
2 |
Reference performance EGPRS2-B, UL, 400 kHz Adjacent channel interference, without brackets |
9.0.0 |
9.1.0 |
|
2009-11 |
44 |
GP-092130 |
0317 |
Correction of remaining errors for EGPRS2 after the split between BTS and MS requirements |
9.0.0 |
9.1.0 |
|
|
2009-11 |
44 |
GP-092149 |
0319 |
1 |
Correction of remaining errors for MCBTS after the split between BTS and MS requirements |
9.0.0 |
9.1.0 |
|
2009-11 |
44 |
GP-092318 |
0320 |
3 |
Addition of requirement to test intra BSS IM attenuation at maximum carrier frequency spacing |
9.0.0 |
9.1.0 |
|
2009-11 |
44 |
GP-092467 |
0322 |
2 |
Correction of application of spurious emission requirements for MCBTS |
9.0.0 |
9.1.0 |
|
2009-11 |
44 |
GP-092151 |
0323 |
1 |
Corrections of references |
9.0.0 |
9.1.0 |
|
2009-11 |
44 |
GP-092335 |
0324 |
4 |
Corrections to minimum receiver requirements for Multi Standard BS in Annex P |
9.0.0 |
9.1.0 |
|
2009-11 |
44 |
GP-092133 |
0327 |
Reference performance, LATRED, EGPRS and EGPRS2-A, DL |
9.0.0 |
9.1.0 |
|
|
2009-11 |
44 |
GP-092136 |
0330 |
1 |
Removal of brackets, EGPRS2 MS requirements |
9.0.0 |
9.1.0 |
|
2009-11 |
44 |
GP-091939 |
0339 |
Correction to GANSS Dynamic Range Requirements |
9.0.0 |
9.1.0 |
|
|
2009-11 |
44 |
GP-092326 |
0340 |
1 |
GANSS minimum performance requirements – closing some open items in sensitivity scenarios |
9.0.0 |
9.1.0 |
|
2009-11 |
44 |
GP-091997 |
0342 |
Correction of Nominal Error Rate (NER) requirements for GSM700 |
9.0.0 |
9.1.0 |
|
|
2009-11 |
44 |
GP-092412 |
0346 |
2 |
Correction to EGPRS2-A, 400 kHz ACI |
9.0.0 |
9.1.0 |
|
2009-11 |
44 |
GP-092312 |
0348 |
1 |
EGPRS2-B uplink spectrum mask |
9.0.0 |
9.1.0 |
|
2010-03 |
45 |
GP-100027 |
0352 |
Clarification to Satellite constellation and assistance data |
9.1.0 |
9.2.0 |
|
|
2010-03 |
45 |
GP-100090 |
0355 |
EGPRS2 EVM requirements for repeater |
9.1.0 |
9.2.0 |
|
|
2010-03 |
45 |
GP-100223 |
0358 |
Removal of brackets, LATRED, EGPRS2-A and miscellaneous corrections |
9.1.0 |
9.2.0 |
|
|
2010-03 |
45 |
GP-100502 |
0368 |
1 |
Reference performance,EGPRS2-A USF, DL, Sensitivity, Co-channel and Adj-channel |
9.1.0 |
9.2.0 |
|
2010-03 |
45 |
GP-100563 |
0370 |
1 |
Corrections and clarifications of the MCBTS requirements |
9.1.0 |
9.2.0 |
|
2010-05 |
46 |
GP-100982 |
0350 |
3 |
Correction of exceptions of Spectrum due to modulation and wideband noise for MCBTS |
9.2.0 |
9.3.0 |
|
2010-05 |
46 |
GP-101035 |
0363 |
4 |
Alignment of blocking requirements in multi-RAT operation and in GSM single-RAT operation for MSR equipment |
9.2.0 |
9.3.0 |
|
2010-05 |
46 |
GP-101041 |
0372 |
3 |
A-GANSS Sensitivity & Dynamic range |
9.2.0 |
9.3.0 |
|
2010-05 |
46 |
GP-100695 |
0375 |
1 |
Introduction of DL performance requirements for EGPRS2-B, Adjacent channel and RTTI/PAN |
9.2.0 |
9.3.0 |
|
2010-05 |
46 |
GP-100795 |
0377 |
Alignment of definition and requirements for spurious emissions with CEPT/ERC/REC 74-01 |
9.2.0 |
9.3.0 |
|
|
2010-05 |
46 |
GP-100825 |
0379 |
Alignment of requirements for out-of-band spurious emissions with CEPT/ERC/REC 74-01 |
9.2.0 |
9.3.0 |
|
|
2010-05 |
46 |
GP-100696 |
0383 |
1 |
Clarification of adjacent timeslot levels |
9.2.0 |
9.3.0 |
|
2010-05 |
46 |
GP-100699 |
0386 |
1 |
Numerous corrections |
9.2.0 |
9.3.0 |
|
2010-05 |
46 |
GP-100993 |
0393 |
Alignment of inband frequency range for GSM 850 with other 3GPP access technologies |
9.2.0 |
9.3.0 |
|
|
2010-05 |
46 |
GP-101038 |
0394 |
1 |
Introduction of requirements for spurious emission in frequency band 20 |
9.2.0 |
9.3.0 |
|
2010-09 |
47 |
GP-101625 |
0398 |
4 |
Introduction of VAMOS performance requirements |
9.3.0 |
9.4.0 |
|
2010-09 |
47 |
GP-101539 |
0400 |
1 |
Clarification of multicarrier BTS receiver requirements |
9.3.0 |
9.4.0 |
|
2010-11 |
48 |
GP-101831 |
0360 |
2 |
Reduction of the number of multicarrier BTS classes |
9.4.0 |
9.5.0 |
|
2010-11 |
48 |
GP-101763 |
0408 |
DL reference performance requirements for EGPRS2-B, USF |
9.4.0 |
9.5.0 |
|
|
2010-11 |
48 |
GP-101766 |
0411 |
DL reference performance requirements for EGPRS2-B – 2nd adjacent channel |
9.4.0 |
9.5.0 |
|
|
2010-11 |
48 |
GP-101996 |
0414 |
1 |
Enhanced numbering of figures and tables |
9.4.0 |
9.5.0 |
|
2010-11 |
48 |
GP-102047 |
0416 |
1 |
Clarification of the measurement of the spectrum exceptions in MCBTS |
9.4.0 |
9.5.0 |
|
2011-03 |
49 |
GP-110423 |
0417 |
1 |
Corrections to A-GNSS values in Annex O |
9.5.0 |
9.6.0 |
|
2011-03 |
49 |
GP-110141 |
0418 |
Correction of equipment types in receiver interference performance |
9.5.0 |
9.6.0 |
|
|
2011-03 |
49 |
GP-110453 |
0421 |
1 |
Reference performance for MCS-0, Sensitivity and Co-channel |
9.5.0 |
9.6.0 |
|
2011-03 |
49 |
GP-110424 |
0424 |
1 |
VAMOS uplink performance requirements |
9.5.0 |
9.6.0 |
|
2011-03 |
49 |
GP-110229 |
0427 |
Corrections of the MCBTS IM requirements |
9.5.0 |
9.6.0 |
|
|
2011-03 |
49 |
GP-110490 |
0428 |
1 |
VAMOS requirements for downlink performance definition |
9.5.0 |
9.6.0 |
|
2011-03 |
49 |
GP-110487 |
0422 |
2 |
TIGHTER Performance requirements |
9.6.0 |
10.0.0 |
|
2011-05 |
50 |
GP-110963 |
0431 |
3 |
Implicit relaxation of DARP-I requirements in DLDC configurations |
10.0.0 |
10.1.0 |
|
2011-05 |
50 |
GP-110981 |
0435 |
1 |
Clarification of AM suppression receiver characteristics for multicarrier BTS equipped with multicarrier receiver |
10.0.0 |
10.1.0 |
|
2011-05 |
50 |
GP-110947 |
0436 |
1 |
Clarification of receiver characteristics for multicarrier BTS equipped with multicarrier receiver |
10.0.0 |
10.1.0 |
|
2011-05 |
50 |
GP-110983 |
0437 |
1 |
Clarification of blocking receiver characteristics for multicarrier BTS equipped with multicarrier receiver |
10.0.0 |
10.1.0 |
|
2011-05 |
50 |
GP-110682 |
0439 |
Miscellanous corrections for MCBTS |
10.0.0 |
10.1.0 |
|
|
2011-05 |
50 |
GP-110688 |
0442 |
Clarification of the out-of-band emission principles for MCBTS |
10.0.0 |
10.1.0 |
|
|
2011-05 |
50 |
GP-110926 |
0444 |
2 |
Correction for equipment types in VAMOS performance requirements |
10.0.0 |
10.1.0 |
|
2011-05 |
50 |
GP-110892 |
0448 |
1 |
Reference performance for MCS-0, Sensitivity and Co-channel [removal of brackets] |
10.0.0 |
10.1.0 |
|
2011-05 |
50 |
GP-110874 |
0450 |
1 |
Power versus time mask for AQPSK |
10.0.0 |
10.1.0 |
|
2011-05 |
50 |
GP-110878 |
0453 |
1 |
Downlink performance requirements for VAMOS MS |
10.0.0 |
10.1.0 |
|
2011-05 |
50 |
GP-110884 |
0456 |
Clarification of test cases for dual antenna terminals using legacy requirements |
10.0.0 |
10.1.0 |
|
|
2011-05 |
50 |
GP-110958 |
0458 |
3 |
Uplink receiver performance requirements for VAMOS |
10.0.0 |
10.1.0 |
|
2011-05 |
50 |
GP-110986 |
0463 |
Removal of VDTS-4 |
10.0.0 |
10.1.0 |
|
|
2011-09 |
51 |
GP-111299 |
0452 |
3 |
Clarification of the notation used for frequency offsets |
10.1.0 |
10.2.0 |
|
2011-09 |
51 |
GP-111099 |
0466 |
Correction to reference interference performance for VAMOS I MS |
10.1.0 |
10.2.0 |
|
|
2011-09 |
51 |
GP-111373 |
0468 |
1 |
EVM for AQPSK for Repeater |
10.1.0 |
10.2.0 |
|
2011-09 |
51 |
GP-111300 |
0470 |
1 |
Correction of some VAMOS-II AHS7.4 RBERII values and a TCH/HS Rber1b typing error for GSM900 VDTS-3 SCPIR = +4dB |
10.1.0 |
10.2.0 |
|
2011-09 |
51 |
GP-111380 |
0471 |
1 |
Interferer signal levels for TIGHTER |
10.1.0 |
10.2.0 |
|
2011-09 |
51 |
GP-111158 |
0472 |
Clarification of references to TS 24.008 |
10.1.0 |
10.2.0 |
|
|
2011-09 |
51 |
GP-111295 |
0473 |
1 |
TIGHTER Performance requirements |
10.1.0 |
10.2.0 |
|
2011-09 |
51 |
GP-111368 |
0475 |
1 |
Introduction of VDTS-4 |
10.1.0 |
10.2.0 |
|
2011-09 |
51 |
GP-111192 |
0477 |
Introduction of EVM requirements for AQPSK |
10.1.0 |
10.2.0 |
|
|
2011-09 |
51 |
GP-111446 |
0479 |
1 |
Uplink receiver performance requirements for VAMOS |
10.1.0 |
10.2.0 |
|
2011-09 |
51 |
GP-111462 |
0481 |
2 |
Clarification of applicability of requirements for spurious response frequencies for multicarrier receiver |
10.1.0 |
10.2.0 |
|
2011-09 |
51 |
GP-111450 |
0483 |
1 |
Reference control channel performance for VAMOS-II MS |
10.1.0 |
10.2.0 |
|
2011-09 |
51 |
GP-111444 |
0485 |
VAMOS II performance requirements |
10.1.0 |
10.2.0 |
|
|
2011-09 |
51 |
GP-111458 |
0487 |
Reference DTX performance requirements for VAMOS-II MS |
10.1.0 |
10.2.0 |
|
|
2011-11 |
52 |
GP-111773 |
0489 |
1 |
On EVM requirements and SCPIR_DL in the case of AQPSK Modulation for Repeater |
10.2.0 |
10.3.0 |
|
2011-11 |
52 |
GP-111742 |
0490 |
1 |
Correction of TIGHTER requirement errors |
10.2.0 |
10.3.0 |
|
2011-11 |
52 |
GP-111743 |
0491 |
1 |
Update of TIGHTER EGPRS2-A requirements |
10.2.0 |
10.3.0 |
|
2011-11 |
52 |
GP-111790 |
0492 |
1 |
Introducing SCH sensitivity TIGHTER requirements |
10.2.0 |
10.3.0 |
|
2011-11 |
52 |
GP-111590 |
0494 |
Correction of VAMOS-II DL DTX requirements |
10.2.0 |
10.3.0 |
|
|
2011-11 |
52 |
GP-111856 |
0496 |
2 |
Correction of VAMOS-II performance requirements |
10.2.0 |
10.3.0 |
|
2011-11 |
52 |
GP-111613 |
0498 |
Correction of VDTS-4 signal levels |
10.2.0 |
10.3.0 |
|
|
2011-11 |
52 |
GP-111620 |
0501 |
Correction to uplink receiver performance requirements for VAMOS and removal of brackets |
10.2.0 |
10.3.0 |
|
|
2011-11 |
52 |
GP-111638 |
0504 |
Clarification on Normal BTS co-location blocking requirements |
10.2.0 |
10.3.0 |
|
|
2011-11 |
52 |
GP-111745 |
0506 |
Removal of brackets for VAMOS BTS requirements |
10.2.0 |
10.3.0 |
|
|
2012-03 |
53 |
GP-120075 |
0508 |
VAMOS-I DL performance requirements |
10.3.0 |
10.4.0 |
|
|
2012-03 |
53 |
GP-120077 |
0510 |
Removal of VAMOS-II square brackets and reference correction |
10.3.0 |
10.4.0 |
|
|
2012-03 |
53 |
GP-120079 |
0512 |
Correction of VAMOS-II DL control channel performance requirements |
10.3.0 |
10.4.0 |
|
|
2012-03 |
53 |
GP-120101 |
0513 |
TIGHTER PDTCH BLER level clarification |
10.3.0 |
10.4.0 |
|
|
2012-03 |
53 |
GP-120102 |
0514 |
TIGHTER – Removal of Square brackets for TCH and Control Channel requirements |
10.3.0 |
10.4.0 |
|
|
2012-03 |
53 |
GP-120118 |
0516 |
Update of Reference clause with 3GPP TS 51.026, repeater RF conformance test specification |
10.3.0 |
10.4.0 |
|
|
2012-03 |
53 |
GP-120171 |
0519 |
Removal of brackets for general receiver performance |
10.3.0 |
10.4.0 |
|
|
2012-03 |
53 |
GP-120289 |
0523 |
Removal of VAMOS-I DL square brackets |
10.3.0 |
10.4.0 |
|
|
2012-03 |
53 |
GP-120410 |
0525 |
Correction to VAMOS-II VDTS-4 performance requirements for TCH/AHS7.4 codec |
10.3.0 |
10.4.0 |
|
|
2012-05 |
54 |
GP-120759 |
0526 |
1 |
TIGHTER – Removal of Square brackets for GPRS and EGPRS requirements |
10.4.0 |
10.5.0 |
|
2012-05 |
54 |
GP-120603 |
0529 |
Removal of VAMOS-I DL square brackets |
10.4.0 |
10.5.0 |
|
|
2012-05 |
54 |
GP-120656 |
0532 |
Correction of co-location blocking table |
10.4.0 |
10.5.0 |
|
|
2012-05 |
54 |
GP-120751 |
0533 |
1 |
TIGHTER – FER / RBER unbalance corrections |
10.4.0 |
10.5.0 |
|
2012-05 |
54 |
GP-120761 |
0527 |
2 |
Introduction of medium range and local area multicarrier BTS classes |
10.5.0 |
11.0.0 |
|
2012-08 |
55 |
GP-120923 |
0534 |
Spurious emission limit in receive band for Medium Range multicarrier BTS |
11.0.0 |
11.1.0 |
|
|
2012-08 |
55 |
GP-121127 |
0535 |
1 |
Correction factor to reference sensitivity and interference requirements for Local Area multicarrier BTS |
11.0.0 |
11.1.0 |
|
2012-08 |
55 |
GP-121128 |
0541 |
2 |
Corrections on medium range and local area multicarrier BTS requirements |
11.0.0 |
11.1.0 |
|
2012-08 |
55 |
GP-120952 |
0544 |
Removal of signal level brackets for VAMOS reference interference performance |
11.0.0 |
11.1.0 |
|
|
2012-08 |
55 |
GP-121136 |
0545 |
1 |
Clarification of output power declaration for Medium Range and Local Area multicarrier BTS |
11.0.0 |
11.1.0 |
|
2012-08 |
55 |
GP-121156 |
0547 |
Clarification of the relation between TIGHTER and DARP phase I MS capability |
11.0.0 |
11.1.0 |
|
|
2012-11 |
56 |
GP-121388 |
0540 |
2 |
Clarification of conformance legacy performance requirements for MSRD terminals |
11.1.0 |
11.2.0 |
|
2012-11 |
56 |
GP-121345 |
0549 |
1 |
VAMOS performance requirements for Local Area multicarrier BTS |
11.1.0 |
11.2.0 |
|
2012-11 |
56 |
GP-121265 |
0550 |
Removal of square brackets for MRLA |
11.1.0 |
11.2.0 |
|
|
2012-11 |
56 |
GP-121347 |
0551 |
1 |
Miscellaneous corrections related to Local Area multicarrier BTS |
11.1.0 |
11.2.0 |
|
2013-03 |
57 |
GP-130112 |
0552 |
Correction to band applicability for in-band blocking |
11.2.0 |
11.3.0 |
|
|
2013-03 |
57 |
GP-130117 |
0553 |
Removal of square brackets for LA VAMOS performance requirements |
11.2.0 |
11.3.0 |
|
|
2013-03 |
57 |
GP-130210 |
0557 |
1 |
Clarification on the interpretation of requirements for MCBTS classes |
11.2.0 |
11.3.0 |
|
2013-08 |
59 |
GP-130876 |
0548 |
6 |
TCRT: Introduction of ER-GSM band |
11.3.0 |
12.0.0 |
|
2013-08 |
59 |
GP-130887 |
0559 |
2 |
Introduction of VAMOS III Performance Requirements |
11.3.0 |
12.0.0 |
|
2013-11 |
60 |
GP-131130 |
0558 |
7 |
Introduction of Downlink Multi Carrier |
12.0.0 |
12.1.0 |
|
2013-11 |
60 |
GP-130980 |
0560 |
Correction to VAMOS III Performance Requirements |
12.0.0 |
12.1.0 |
|
|
2013-11 |
60 |
GP-131009 |
0566 |
Correction to Multi interferer model for MSRD |
12.0.0 |
12.1.0 |
|
|
2013-11 |
60 |
GP-131109 |
0567 |
Correction of typo in ER-GSM implementation |
12.0.0 |
12.1.0 |
|
|
2014-05 |
62 |
GP-140348 |
0568 |
2 |
DLMC: Introduction of CS-3 for PACCH |
12.1.0 |
12.2.0 |
|
2014-05 |
62 |
GP-140400 |
0569 |
2 |
VAMOS III Performance Requirements |
12.1.0 |
12.2.0 |
|
2014-05 |
62 |
GP-140389 |
0570 |
1 |
DLMC – Corrections |
12.1.0 |
12.2.0 |
|
2014-08 |
63 |
GP-140436 |
0571 |
Introduction of BDS in GERAN |
12.2.0 |
12.3.0 |
|
|
2014-08 |
63 |
GP-140576 |
0572 |
VAMOS III Performance Requirements – FER |
12.2.0 |
12.3.0 |
|
|
2014-08 |
63 |
GP-140577 |
0573 |
VAMOS III Performance Requirements – RBER |
12.2.0 |
12.3.0 |
|
|
2014-08 |
63 |
GP-140586 |
0575 |
Removal of brackets for DLMC requirements |
12.2.0 |
12.3.0 |
|
|
2014-11 |
64 |
GP-140912 |
0576 |
Bracket Removal from VAMOS III RBER Specification |
12.3.0 |
12.4.0 |
|
|
2015-03 |
65 |
GP150294 |
0577 |
Corrections on VAMOS III Performance Requirements for VDTS4 – RBER |
12.4.0 |
12.5.0 |
|
|
2015-12 |
68 |
Version for Release 13 (frozen at SP-70) |
12.5.0 |
13.0.0 |
|||
|
Change history |
|||||||
|
Date |
Meeting |
TDoc |
CR |
Rev |
Cat |
Subject/Comment |
New version |
|
2016-05 |
70 |
GP-160498 |
0578 |
9 |
B |
Introduction of EC-GSM-IoT |
13.1.0 |
|
2016-05 |
70 |
GP-160505 |
0581 |
1 |
B |
BTS sensitivity performance requirements for EC-GSM-IoT |
13.1.0 |
|
2016-05 |
70 |
GP-160506 |
0582 |
1 |
B |
BTS interference performance requirements for EC-GSM-IoT |
13.1.0 |
|
2016-09 |
73 |
RP-161390 |
0583 |
1 |
B |
MS performance requirements for EC-GSM-IoT |
13.2.0 |
|
2016-09 |
73 |
RP-161392 |
0584 |
3 |
F |
Miscellaneous corrections for EC-GSM-IoT |
13.2.0 |
|
2016-09 |
73 |
RP-161390 |
0585 |
1 |
F |
Incremental redundancy requirement for EC-GSM-IoT |
13.2.0 |
|
2016-09 |
73 |
RP-161390 |
0586 |
2 |
F |
BTS interference performance requirements for EC-GSM-IoT |
13.2.0 |
|
2016-09 |
73 |
RP-161390 |
0587 |
2 |
F |
BTS sensitivity performance requirements for EC-GSM-IoT |
13.2.0 |
|
2016-09 |
73 |
RP-161390 |
0588 |
1 |
F |
Normalized coherency error requirements for EC-GSM-IoT MS |
13.2.0 |
|
2016-09 |
73 |
RP-161390 |
0589 |
3 |
F |
BTS sensitivity performance requirements for Overlaid CDMA |
13.2.0 |
|
2016-09 |
73 |
RP-161392 |
0590 |
2 |
F |
Corrections to EC-GSM-IoT |
13.2.0 |
|
2016-09 |
Editorial corrections |
||||||
|
2016-12 |
74 |
RP-162070 |
0591 |
– |
F |
MS performance requirements for EC-GSM-IoT: removal of square brackets and correction of a performance figure (typo) |
13.3.0 |
|
2016-12 |
74 |
RP-162070 |
0592 |
1 |
F |
BTS interference performance requirements for EC-GSM-IoT – removal of brackets |
13.3.0 |
|
2016-12 |
74 |
RP-162070 |
0593 |
– |
F |
BTS sensitivity performance requirements for EC-GSM-IoT – removal of brackets |
13.3.0 |
|
2016-12 |
74 |
RP-162070 |
0594 |
1 |
F |
Miscellaneous corrections to EC-GSM-IoT |
13.3.0 |
|
2016-12 |
74 |
RP-162070 |
0595 |
– |
F |
8PSK performance for EC-GSM-IoT BTS |
13.3.0 |
|
2017-03 |
75 |
RP-170064 |
0596 |
– |
F |
8PSK performance for EC-GSM-IoT BTS – removal of brackets |
13.4.0 |
|
2017-03 |
75 |
RP-170064 |
0597 |
– |
F |
BTS sensitivity performance requirements for Overlaid CDMA – removal of brackets |
13.4.0 |
|
2017-03 |
75 |
RP-170551 |
0598 |
2 |
B |
Introduction of Extended Access Burst for connectionless Multilateration Positioning |
14.0.0 |
|
2017-06 |
76 |
RP-170924 |
0599 |
3 |
B |
Performance requirements for Alternative Mappings for Higher Coverage Classes with 2 PDCHs |
14.1.0 |
|
2017-06 |
76 |
RP-170923 |
0603 |
1 |
B |
Receiver Performance for Extended Access Burst |
14.1.0 |
|
2017-06 |
76 |
RP-170924 |
0604 |
4 |
B |
Performance requirements for new uplink coverage class CC5 for UL MCL improvement |
14.1.0 |
|
2017-09 |
77 |
RP-171595 |
0606 |
2 |
F |
Performance requirements for uplink CC5 and for Alternative Coverage Class mapping method |
14.2.0 |
|
2017-09 |
77 |
RP-171594 |
0608 |
1 |
F |
Performance Requirements for Extended AB |
14.2.0 |
|
2017-12 |
78 |
RP-172188 |
0609 |
1 |
F |
Performance requirements for uplink CC5 and for Alternative Coverage Class mapping |
14.3.0 |
|
2017-12 |
78 |
RP-172188 |
0610 |
– |
F |
Performance requirements for Alternative Coverage Class mapping and CC5 using OLCDMA |
14.3.0 |
|
2018-03 |
79 |
RP-180071 |
0612 |
– |
F |
Finalised performance requirements for Alternative Coverage Class mapping and CC5 using OLCDMA |
14.4.0 |
|
2018-03 |
79 |
RP-180070 |
0613 |
– |
A |
Miscellaneous corrections for EC-GSM-IoT |
14.4.0 |
|
2018-06 |
80 |
RP-180824 |
0615 |
– |
F |
Corrections to normalized coherency error for EDAB and to Annex S |
14.5.0 |
|
2018-06 |
80 |
Version for Release 15 |
15.0.0 |
||||
|
2018-09 |
81 |
RP-181593 |
0616 |
– |
B |
Introduction of EC-PICH performance requirements |
15.1.0 |
|
2019-03 |
83 |
RP-190062 |
0619 |
1 |
A |
Adjacent 400 kHz interference requirements for EC-GSM-IoT |
15.2.0 |
|
2019-03 |
83 |
RP-190060 |
0621 |
– |
F |
Indication of performance requirements based on 30% BLER |
16.0.0 |
|
2020-03 |
87e |
RP-200053 |
0625 |
– |
A |
Removal of brackets for EC-GSM-IoT, SACCH for AMR and TIGHTER requirements |
16.1.0 |
|
2020-03 |
87e |
RP-200055 |
0627 |
– |
A |
Removal of brackets for EC-PICH reference performance |
16.1.0 |
|
2022-03 |
RP-95e |
– |
– |
– |
– |
Upgrade to Rel-17 version without technical change |
17.0.0 |