11.3.2 UAC / Access Identity 0 / 0% access probability / Paging for MT access/Emergency call
38.523-13GPP5GSPart 1: ProtocolRelease 17TSUser Equipment (UE) conformance specification
11.3.2.1 Test Purpose (TP)
(1)
with { UE not configured for special AIs (1,2,11-15) having received a SIB1 message indicating 0% accessibility for all Access Categories in NR RRC_Idle state }
ensure that {
when { UE is paged for MT access }
then { UE does not consider the access as barred and initiates RRC Connection }
}
(2)
with { UE not configured for special AIs (1,2,11-15) having received a SIB1 message including UAC Info set to 0% accessibility for Access Category 2 in NR RRC_Idle state }
ensure that {
when { UE attempts emergency call }
then { UE does not initiate emergency call }
}
(3)
with { UE not configured for special AIs (1,2,11-15) with T302 running but T390 expired for Access Category 2 and with SIB1 including UAC Info indicating 100% accessibility for Access Category 2 in NR RRC_IDLE state }
ensure that {
when { UE attempts emergency call }
then { UE does not consider the access attempt as barred and initiates the emergency call }
}
11.3.2.2 Conformance requirements
References: The conformance requirements covered in the present TC are specified in TS 24.501: clause 4.5.2, 4.5.4.1 and 4.5.6 and TS 38.331: clause 5.3.14.1, 5.3.14.2, 5.3.14.4 and 5.3.14.5. Unless otherwise stated these are Rel-15 requirements.
[TS 24.501, clause 4.5.2]
When the UE needs to initiate an access attempt in one of the events listed in subclause 4.5.1, the UE shall determine one or more access identities from the set of standardized access identities, and one access category from the set of standardized access categories and operator-defined access categories, to be associated with that access attempt.
The set of the access identities applicable for the request is determined by the UE in the following way:
a) for each of the access identities 1, 2, 11, 12, 13, 14 and 15 in table 4.5.2.1, the UE shall check whether the access identity is applicable in the selected PLMN, if a new PLMN is selected, or otherwise if it is applicable in the RPLMN or equivalent PLMN; and
b) if none of the above access identities is applicable, then access identity 0 is applicable.
Table 4.5.2.1: Access identities
|
Access Identity number |
UE configuration |
|
0 |
UE is not configured with any parameters from this table |
|
1 (NOTE 1) |
UE is configured for multimedia priority service (MPS). |
|
2 (NOTE 2) |
UE is configured for mission critical service (MCS). |
|
3-10 |
Reserved for future use |
|
11 (NOTE 3) |
Access Class 11 is configured in the UE. |
|
12 (NOTE 3) |
Access Class 12 is configured in the UE. |
|
13 (NOTE 3) |
Access Class 13 is configured in the UE. |
|
14 (NOTE 3) |
Access Class 14 is configured in the UE. |
|
15 (NOTE 3) |
Access Class 15 is configured in the UE. |
|
NOTE 1: Access identity 1 is valid when: NOTE 2: Access identity 2 is used by UEs configured for MCS and is valid when: NOTE 3: Access identities 11 and 15 are valid in HPLMN (if the EHPLMN list is not present or is empty) or EHPLMN (if the EHPLMN list is present). Access Identities 12, 13 and 14 are valid in HPLMN and visited PLMNs of home country only (see the definition of home country in 3GPP TS 24.301 [15]). |
|
The UE uses the MPS indicator bit of the 5GS network feature support IE to determine if access identity 1 is valid. Processing of the MPS indicator bit of the 5GS network feature support IE in the REGISTRATION ACCEPT message is described in subclause 5.5.1.2.4 and subclause 5.5.1.3.4. The UE shall not consider access identity 1 to be valid when the UE is not in the country of its HPLMN prior to receiving the MPS indicator bit of the 5GS network feature support IE in the REGISTRATION ACCEPT message being set to "Access identity 1 valid in RPLMN or equivalent PLMN".
When the UE is in the country of its HPLMN, the contents of the USIM files EFUAC_AIC and EFACC as specified in 3GPP TS 31.102 [22] and the rules specified in table 4.5.2.1 are used to determine the applicability of access identity 1 and access classes 11 – 15. When the UE is in the country of its HPLMN, and the USIM file EFUAC_AIC does not indicate the UE is configured for access identity 1, the UE uses the MPS indicator bit of the 5GS network feature support IE in the REGISTRATION ACCEPT message to determine if access identity 1 is valid. When the UE is in the country of its HPLMN, and the USIM file EFUAC_AIC indicates the UE is configured for access identity 1, the MPS indicator bit of the 5GS network feature support IE is not applicable. When the UE is not in the country of its HPLMN, the contents of the USIM files EFUAC_AIC and EFACC are not applicable.
The UE uses the MCS indicator bit of the 5GS network feature support IE to determine if access identity 2 is valid. Processing of the MCS indicator bit of the 5GS network feature support IE in the REGISTRATION ACCEPT message is described in subclause 5.5.1.2.4 and subclause 5.5.1.3.4. The UE shall not consider access identity 2 to be valid when the UE is not in the country of its HPLMN prior to receiving the MCS indicator bit of the 5GS network feature support IE in the REGISTRATION ACCEPT message being set to "Access identity 2 valid in RPLMN or equivalent PLMN".
When the UE is in the country of its HPLMN, the contents of the USIM files EFUAC_AIC and EFACC as specified in 3GPP TS 31.102 [22] and the rules specified in table 4.5.2.1 are used to determine the applicability of access identity 2 and access classes 11 – 15. When the UE is in the country of its HPLMN, and the USIM file EFUAC_AIC does not indicate the UE is configured for access identity 2, the UE uses the MCS indicator bit of the 5GS network feature support IE in the REGISTRATION ACCEPT message to determine if access identity 2 is valid. When the UE is in the country of its HPLMN, and the USIM file EFUAC_AIC indicates the UE is configured for access identity 2, the MCS indicator bit of the 5GS network feature support IE is not applicable. When the UE is not in the country of its HPLMN, the contents of the USIM files EFUAC_AIC and EFACC are not applicable.
In order to determine the access category applicable for the access attempt, the NAS shall check the rules in table 4.5.2.2, and use the access category for which there is a match for barring check. If the access attempt matches more than one rule, the access category of the lowest rule number shall be selected. If the access attempt matches more than one operator-defined access category definition, the UE shall select the access category from the operator-defined access category definition with the lowest precedence value (see subclause 4.5.3).
NOTE: The case when an access attempt matches more than one rule includes the case when multiple events trigger an access attempt at the same time.
Table 4.5.2.2: Mapping table for access categories
|
Rule # |
Type of access attempt |
Requirements to be met |
Access Category |
|
1 |
Response to paging or NOTIFICATION over non-3GPP access; 5GMM connection management procedure initiated for the purpose of transporting an LPP message |
Access attempt is for MT access |
0 (= MT_acc) |
|
2 |
Emergency |
UE is attempting access for an emergency session (NOTE 1, NOTE 2) |
2 (= emergency) |
|
3 |
Access attempt for operator-defined access category |
UE stores operator-defined access category definitions valid in the current PLMN as specified in subclause 4.5.3, and access attempt is matching criteria of an operator-defined access category definition |
32-63 |
|
4 |
Access attempt for delay tolerant service |
(a) UE is configured for NAS signalling low priority or UE supporting S1 mode is configured for EAB (see the "ExtendedAccessBarring" leaf of NAS configuration MO in 3GPP TS 24.368 [17] or 3GPP TS 31.102 [22]) where "EAB override" does not apply, and (b). the UE received one of the categories a, b or c as part of the parameters for unified access control in the broadcast system information, and the UE is a member of the broadcasted category in the selected PLMN or RPLMN/equivalent PLMN (NOTE 3, NOTE 5, NOTE 6, NOTE 7, NOTE 8) |
1 (= delay tolerant) |
|
5 |
MO MMTel voice call |
Access attempt is for MO MMTel voice call or for NAS signalling connection recovery during ongoing MO MMTel voice call (NOTE 2) |
4 (= MO MMTel voice) |
|
6 |
MO MMTel video call |
Access attempt is for MO MMTel video call or for NAS signalling connection recovery during ongoing MO MMTel video call (NOTE 2) |
5 (= MO MMTel video) |
|
7 |
MO SMS over NAS or MO SMSoIP |
Access attempt is for MO SMS over NAS (NOTE 4) or MO SMS over SMSoIP transfer or for NAS signalling connection recovery during ongoing MO SMS or SMSoIP transfer (NOTE 2) |
6 (= MO SMS and SMSoIP) |
|
8 |
UE NAS initiated 5GMM specific procedures |
Access attempt is for MO signalling |
3 (= MO_sig) |
|
9 |
UE NAS initiated 5GMM connection management procedure or 5GMM NAS transport procedure |
Access attempt is for MO data |
7 (= MO_data) |
|
10 |
An uplink user data packet is to be sent for a PDU session with suspended user-plane resources |
No further requirement is to be met |
7 (= MO_data) |
|
NOTE 1: This includes 5GMM specific procedures while the service is ongoing and 5GMM connection management procedures required to establish a PDU session with request type = "initial emergency request" or "existing emergency PDU session", or to re-establish user-plane resources for such a PDU session. This further includes the service request procedure initiated with a SERVICE REQUEST message with the Service type IE set to "emergency services fallback".< NOTE 2: Access for the purpose of NAS signalling connection recovery during an ongoing service, or for the purpose of NAS signalling connection establishment following fallback indication from lower layers during an ongoing service, is mapped to the access category of the ongoing service in order to derive an RRC establishment cause, but barring checks will be skipped for this access attempt. NOTE 3: If the UE selects a new PLMN, then the selected PLMN is used to check the membership; otherwise the UE uses the RLPMN or a PLMN equivalent to the RPLMN. NOTE 4: This includes the 5GMM connection management procedures triggered by the UE-initiated NAS transport procedure for transporting the MO SMS. NOTE 5: The UE configured for NAS signalling low priority is not supported in this release of specification. If a UE supporting both S1 mode and N1 mode is configured for NAS signalling low priority in S1 mode as specified in 3GPP TS 24.368 [17] or 3GPP TS 31.102 [22], the UE shall ignore the configuration for NAS signalling low priority when in N1 mode. NOTE 6: If the access category applicable for the access attempt is 1, then the UE shall additionally determine a second access category from the range 3 to 7. If more than one access category matches, the access category of the lowest rule number shall be chosen. The UE shall use the second access category only to derive an RRC establishment cause for the access attempt. NOTE 7: "EAB override" does not apply, if the UE is not configured to allow overriding EAB (see the "Override_ExtendedAccessBarring" leaf of NAS configuration MO in 3GPP TS 24.368 [17] or 3GPP TS 31.102 [22]), or if NAS has not received an indication from the upper layers to override EAB and the UE does not have a PDU session that was established with EAB override. NOTE 8: For the definition of categories a, b and c associated with access category 1, see 3GPP TS 22.261 [3]. The categories associated with access category 1 are distinct from the categories a, b and c associated with EAB (see 3GPP TS 22.011 [1A]). |
|||
[TS 24.501, clause 4.5.4.1]
When the UE is in 5GMM-IDLE mode, upon receiving a request from the upper layers for an access attempt, the NAS shall categorize the access attempt into access identities and an access category following subclause 4.5.2, table 4.5.2.1 and table 4.5.2.2, and subclause 4.5.3, and provide the applicable access identities and the access category to the lower layers for the purpose of access control checking. In this request to the lower layer the NAS can also provide to the lower layer the RRC establishment cause determined as specified in subclause 4.5.6 of this specification.
NOTE 1: The access barring check is performed by the lower layers.
NOTE 2: As an implementation option, the NAS can provide the RRC establishment cause to the lower layers after being informed by the lower layers that the access attempt is allowed.
If the UE has uplink user data pending for one or more PDU sessions when it builds a REGISTRATION REQUEST or SERVICE REQUEST message as initial NAS message, the UE shall indicate the respective PDU sessions in the Uplink data status IE as specified in subclause 5.5.1.3.2 and 5.6.1.2, regardless of the access category for which the access barring check is performed.
NOTE 3: The UE indicates pending user data for all the respective PDU sessions, even if barring timers are running for some of the corresponding access categories.
If the lower layers indicate that the access attempt is allowed, the NAS shall initiate the procedure to send the initial NAS message for the access attempt.
If the lower layers indicate that the access attempt is barred, the NAS shall not initiate the procedure to send the initial NAS message for the access attempt. Additionally:
a) if the event which triggered the access attempt was an MO-MMTEL-voice-call-started indication or an MO-MMTEL-video-call-started indication:
1) if the UE is operating in the single-registration mode and the UE’s usage setting is "voice centric", the UE may attempt to select an E-UTRA cell connected to EPC. If the UE finds a suitable E-UTRA cell connected to EPC, it then proceeds with the appropriate EMM specific procedures and, if necessary, ESM procedures to make a PDN connection providing access to IMS available; see subclause 4.8.2 and 3GPP TS 24.301 [15];
2) if the UE is operating in the dual-registration mode, the UE may proceed in S1 mode with the appropriate EMM specific procedures and ESM procedures to make a PDN connection providing access to IMS available; see subclause 4.8.3 and 3GPP TS 24.301 [15];
3) otherwise, the NAS shall notify the upper layers that the access attempt is barred. In this case, upon receiving an indication from the lower layers that the barring is alleviated for the access category with which the access attempt was associated, the NAS shall notify the upper layers that the barring is alleviated for the access category and may initiate the procedure to send the initial NAS message, if still needed; and
b) if the event which triggered the access attempt was an MO-SMSoIP-attempt-started indication:
1) if the UE is operating in the single-registration mode, the UE may attempt to select an E-UTRA cell connected to EPC. If the UE finds a suitable E-UTRA cell connected to EPC, it then proceeds with the appropriate EMM specific procedures and, if necessary, ESM procedures to make a PDN connection providing access to IMS available; see subclause 4.8.2 and 3GPP TS 24.301 [15];
2) if the UE is operating in the dual-registration mode, the UE may proceed in S1 mode with the appropriate EMM specific procedures and ESM procedures to make a PDN connection providing access to IMS available; see subclause 4.8.3 and 3GPP TS 24.301 [15];
3) otherwise, the NAS layer shall notify the upper layers that the access attempt is barred. In this case, upon receiving an indication from the lower layers that the barring is alleviated for the access category with which the access attempt was associated, the NAS shall notify the upper layers that the barring is alleviated for the access category and may initiate the procedure to send the initial NAS message, if still needed.
NOTE 4: Barring timers, on a per access category basis, are run by the lower layers. At expiry of barring timers, the indication of alleviation of access barring is indicated to the NAS on a per access category basis.
[TS 24.501, clause 4.5.6]
When 5GMM requests the establishment of a NAS-signalling connection, the RRC establishment cause used by the UE shall be selected according to one or more access identities (see subclause 4.5.2) and the determined access category as specified in table 4.5.6.1 and table 4.5.6.2. If the determined access category is an operator-defined access category, then the RRC establishment cause used by the UE shall be selected according to table 4.5.6.1 and table 4.5.6.2 based on one or more access identities (see subclause 4.5.2) and the standardized access category determined for the operator-defined access category as described in subclause 4.5.3.
Table 4.5.6.1: Mapping table for access identities/access categories and RRC establishment cause when establishing N1 NAS signalling connection via NR connected to 5GCN
|
Access identities |
Access categories |
RRC establishment cause is set to |
|
0 |
0 (= MT_acc) |
mt-Access |
|
1 (= delay tolerant) |
Not applicable (NOTE 1) |
|
|
2 (= emergency) |
emergency |
|
|
3 (= MO_sig) |
mo-Signalling |
|
|
4 (= MO MMTel voice) |
mo-VoiceCall |
|
|
5 (= MO MMTel video) |
mo-VideoCall |
|
|
6 (= MO SMS and SMSoIP) |
mo-SMS |
|
|
7 (= MO_data) |
mo-Data |
|
|
1 |
Any category |
mps-PriorityAccess |
|
2 |
Any category |
mcs-PriorityAccess |
|
11, 15 |
Any category |
highPriorityAccess |
|
12,13,14, |
Any category |
highPriorityAccess |
|
NOTE 1: A UE using access category 1 for the access barring check will determine a second access category in the range 3 to 7 that is to be used for determination of the RRC establishment cause. See subclause 4.5.2, table 4.5.2.2, NOTE 6. NOTE 2: See subclause 4.5.2, table 4.5.2.1 for use of the access identities of 0, 1, 2, and 11-15. |
||
Table 4.5.6.2: Mapping table for access identities/access categories and RRC establishment cause when establishing N1 NAS signalling connection via E-UTRA connected to 5GCN
|
Access identities |
Access categories |
RRC establishment cause is set to |
|
0 |
0 (= MT_acc) |
mt-Access |
|
1 (= delay tolerant) |
Not applicable (NOTE 1) |
|
|
2 (= emergency) |
emergency |
|
|
3 (= MO_sig) |
mo-Signalling |
|
|
4 (= MO MMTel voice) |
mo-VoiceCall |
|
|
5 (= MO MMTel video) |
mo-VoiceCall |
|
|
6 (= MO SMS and SMSoIP) |
mo-Data |
|
|
7 (= MO_data) |
mo-Data |
|
|
1 |
Any category |
highPriorityAccess |
|
2 |
Any category |
highPriorityAccess |
|
11, 15 |
Any category |
highPriorityAccess |
|
12,13,14, |
Any category |
highPriorityAccess |
|
NOTE 1: A UE using access category 1 for the access barring check will determine a second access category in the range 3 to 7 that is to be used for determination of the RRC establishment cause. See subclause 4.5.2, table 4.5.2.2, NOTE 6. NOTE 2: See subclause 4.5.2, table 4.5.2.1 for use of the access identities of 0, 1, 2, and 11-15. |
||
[TS 38.331, clause 5.3.14.1]
The purpose of this procedure is to perform access barring check for an access attempt associated with a given Access Category and one or more Access Identities upon request from upper layers according to TS 24.501 [23] or the RRC layer.
After a handover resulting in change of PCell in RRC_CONNECTED the UE shall defer access barring checks until it has obtained valid UAC information (from SIB1) from the target cell.
[TS 38.331, clause 5.3.14.2]
Upon initiation of the procedure, the UE shall:
1> if timer T390 is running for the Access Category:
2> consider the access attempt as barred;
1> else if timer T302 is running and the Access Category is neither ‘2’ nor ‘0’:
2> consider the access attempt as barred;
1> else:
2> if the Access Category is ‘0’:
3> consider the access attempt as allowed;
2> else:
3> if SIB1 includes uac-BarringPerPLMN-List and the uac-BarringPerPLMN-List contains an UAC-BarringPerPLMN entry with the plmn-IdentityIndex corresponding to the PLMN selected by upper layers (see TS 24.501 [23]):
4> select the UAC-BarringPerPLMN entry with the plmn-IdentityIndex corresponding to the PLMN selected by upper layers;
4> in the remainder of this procedure, use the selected UAC-BarringPerPLMN entry (i.e. presence or absence of access barring parameters in this entry) irrespective of the uac-BarringForCommon included in SIB1;
3> else if SIB1 includes uac-BarringForCommon:
4> in the remainder of this procedure use the uac-BarringForCommon (i.e. presence or absence of these parameters) included in SIB1;
3> else:
4> consider the access attempt as allowed;
…
1> if the access barring check was requested by upper layers:
2> if the access attempt is considered as barred:
3> if timer T302 is running:
4> inform the upper layer that access barring is applicable for all access categories except categories ‘0’ and ‘2’, upon which the procedure ends;
3> else:
4> inform upper layers that the access attempt for the Access Category is barred, upon which the procedure ends;
2> else:
3> inform upper layers that the access attempt for the Access Category is allowed, upon which the procedure ends;
1> else:
2> the procedure ends.
[TS 38.331, clause 5.3.14.4]
The UE shall:
1> if timer T302 expires or is stopped, and if timer T390 corresponding to an Access Category is not running; or
1> if timer T390 corresponding to an Access Category other than ‘2’ expires or is stopped, and if timer T302 is not running; or
1> if timer T390 corresponding to the Access Category ‘2’ expires or is stopped:
2> consider the barring for this Access Category to be alleviated;
1> when barring for an Access Category is considered being alleviated:
2> if the Access Category was informed to upper layers as barred:
3> inform upper layers about barring alleviation for the Access Category.
2> if barring is alleviated for Access Category ‘8’:
3> perform actions specified in 5.3.13.8;
[TS 38.331, clause 5.3.14.5]
The UE shall:
1> if one or more Access Identities are indicated according to TS 24.501 [23], and
1> if for at least one of these Access Identities the corresponding bit in the uac-BarringForAccessIdentity contained in "UAC barring parameter" is set to zero:
2> consider the access attempt as allowed;
1> else:
2> draw a random number ‘rand‘ uniformly distributed in the range: 0 ≤ rand < 1;
2> if ‘rand‘ is lower than the value indicated by uac-BarringFactor included in "UAC barring parameter":
3> consider the access attempt as allowed;
2> else:
3> consider the access attempt as barred;
1> if the access attempt is considered as barred:
2> draw a random number ‘rand‘ that is uniformly distributed in the range 0 ≤ rand < 1;
2> start timer T390 for the Access Category with the timer value calculated as follows, using the uac-BarringTime included in "AC barring parameter":
T390 = (0.7+ 0.6 * rand) * uac-BarringTime.
11.3.2.3 Test description
11.3.2.3.1 Pre-test conditions
System Simulator:
– NR Cell 1.
– System information combination NR-1 as defined in TS 38.508-1 [4] Table 4.4.3.1.2-1 is used in NR cell 1 with SIB 1 modified as per Table 11.3.2.3.3-1.
UE:
– None.
Preamble:
– The UE is brought to state 1N-A, RRC_IDLE Connectivity (NR), in accordance with the procedure described in TS 38.508-1 [4], Table 4.5.2.2-2.
11.3.2.3.2 Test procedure sequence
Table 11.3.2.3.2-1: Main behaviour
|
St |
Procedure |
Message Sequence |
TP |
Verdict |
|
|
U – S |
Message |
||||
|
1 |
Make the UE attempt an emergency call dialling a number which is stored on the ME (e.g. 112 or 911). (Note 1) |
– |
– |
– |
– |
|
2 |
Check: Does the UE transmit an RRCSetupRequest message with establishmentCause set to ’emergency’ within 30 s’? |
–> |
NR RRC: RRCSetupRequest |
2 |
F |
|
2A1 |
IF pc_SwitchOnOff THEN switch off UE, ELSE IF pc_USIM_Removal THEN remove the USIM, ELSE power off UE in which case steps 2A2 to 2A4 are not performed. |
– |
– |
– |
– |
|
2A2 |
SS starts timer T_Delay=15 sec. |
– |
– |
– |
– |
|
– |
EXCEPTION: Steps 2A3a1-2A3b1 describes optional behaviour that depends on the UE implementation; the "lower case letter" identifies a step sequence that take place if a particular implementation is under test. |
– |
– |
– |
– |
|
2A3a1 |
Steps 1a2-1a4 of the Switch off procedure in RRC_IDLE in table 4.9.6.1-1 in TS 38.508-1 [4] are performed. |
– |
– |
– |
– |
|
2A3a2 |
Stop timer T_Delay. |
– |
– |
– |
– |
|
2A3a3 |
The SS transmits an RRCRelease message. |
<– |
NR RRC: RRCRelease |
– |
– |
|
2A3b1 |
Timer T_Delay expires. |
– |
– |
– |
– |
|
2A4 |
Void |
– |
– |
– |
– |
|
2A5 |
Switch on the UE. |
– |
– |
– |
– |
|
2A6 |
The UE performs Registration procedure as specified in TS 38.508-1 [4] subclause 4.5.2. |
– |
– |
– |
– |
|
3 |
SS changes SIB1 according to Table 11.3.2.3.3-2 and sends Short Message on PDCCH using P-RNTI. Wait for 2.1* modification period to allow the new system information to take effect and T390 expire. (Note 1) |
<– |
PDCCH (DCI 1_0): Short Message |
– |
– |
|
4 |
The SS transmits a Paging message including a matched ng-5G-S-TMSI. |
<– |
NR RRC: Paging |
– |
– |
|
5 |
Check: Does the UE transmit an RRCSetupRequest message with establishmentCause set to ‘mt-access’? |
–> |
NR RRC: RRCSetupRequest |
1 |
P |
|
6-12 |
Steps 3 to 9a1 of the generic test procedure in TS 38.508-1 [4] Table 4.9.4.2.2-1 are performed on NR Cell 1. |
– |
– |
– |
– |
|
13 |
SS changes SIB1 according to 38.508-1 [4] Table 4.6.1-28 and sends Short Message on PDCCH using P-RNTI. Wait for 2.1* modification period to allow the new system information to take effect. |
<– |
PDCCH (DCI 1_0): Short Message |
– |
– |
|
14-15 |
Steps 1-2 of the NR RRC_CONNECTED procedure in table 4.5.4.2-3 in TS 38.508-1 [4] are performed. |
– |
– |
– |
– |
|
16 |
The SS responds with RRCReject message with IE waitTime set to 16s(T302). |
<– |
NR RRC: RRCReject |
– |
– |
|
17 |
Make the UE attempt an emergency call dialling a number which is stored on the ME (e.g. 112 or 911), before the T302 timer expires. |
– |
– |
– |
– |
|
18 |
Check: Does the UE transmit an RRCSetupRequest message with establishmentCause set to ’emergency’ (Note 2)? |
–> |
NR RRC: RRCSetupRequest |
3 |
P |
|
19 |
Void |
– |
– |
– |
– |
|
20 |
Void |
– |
– |
– |
– |
|
– |
EXCEPTION: Steps 21a1 – 21b6 describe the UE behaviour that depends on UE capability; the “lower case letter” identifies a step sequence that takes place if a capability is supported |
– |
– |
– |
– |
|
21a1-21a12 |
IF pc_NR_5GC_EmergencyServices THEN Step 2-13 for IMS Emergency call establishment are performed as specified in TS 38.508-1 [4], subclause 4.9.11 on NR Cell 1. |
– |
– |
– |
– |
|
21a13 |
Make the UE release the emergency call. (NOTE 3) |
– |
– |
– |
– |
|
21a14 |
Test procedure for IMS MO Emergency call release is performed as specified in TS 38.508-1 [4], subclause 4.9.12A on NR Cell 1. |
– |
– |
– |
– |
|
21b1 – 21b4 |
ELSE Step 2- 5 for IMS Emergency call establishment are performed as specified in TS 38.508-1 [4], subclause 4.9.11 on NR Cell 1. |
– |
– |
– |
– |
|
21b5 |
IF pc_SwitchOnOff THEN switch off UE, IF pc_USIM_Removal THEN remove the USIM. |
– |
– |
– |
– |
|
21b6 |
SS starts timer1 = 15 sec to see if UE performs optional Step 21b6a1 |
– |
– |
– |
– |
|
– |
EXCEPTION: Steps 21b6a1-21b6b1 describes optional behaviour that depends on the UE implementation; the "lower case letter" identifies a step sequence that take place if a particular implementation is under test. |
– |
– |
– |
– |
|
21b6a1 |
The UE transmits a DEREGISTRATION REQUEST message. |
–> |
NR RRC: ULInformationTransfer 5GMM: DEREGISTRATION REQUEST |
– |
– |
|
21b6a2 |
The SS transmits an RRCRelease message. |
<– |
NR RRC: RRCRelease |
||
|
21b6b1 |
ELSE power off UE. |
– |
– |
– |
– |
|
Note 1: T390 is a random value between (0.7 + 0.6 * 0) * uac-BarringTime(4s) = 2.8s and (0.7 + 0.6 * 1) * uac-BarringTime(4s) = 5.2s, which will start after UE attempts an emergency call. Note2: The emergency call dialling and UE RRCsetupRequest message should be initiated before T302 timer expires. Note 3: This could be done by e.g. MMI or AT command. |
|||||
11.3.2.3.3 Specific message contents
Table 11.3.2.3.3-1: SIB1 for NR Cell 1 (Preamble, table 11.3.2.3.2-1)
|
Derivation Path: TS 38.508-1 [4], Table 4.6.1-28 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
SIB1 ::= SEQUENCE { |
|||
|
uac-BarringInfo SEQUENCE { |
|||
|
uac-BarringForCommon SEQUENCE (SIZE (1..maxAccessCat-1)) OF UAC-BarringPerCat { |
1 entry |
||
|
UAC-BarringPerCat[1] SEQUENCE { |
entry 1 |
||
|
accessCategory |
2 |
||
|
uac-barringInfoSetIndex |
1 |
||
|
} |
|||
|
} |
|||
|
uac-BarringPerPLMN-List |
Not present |
||
|
uac-BarringInfoSetList SEQUENCE (SIZE(1..maxBarringInfoSet)) OF UAC-BarringInfoSet { |
1 entry |
||
|
UAC-BarringInfoSet[1] SEQUENCE { |
entry 1 |
||
|
uac-BarringFactor |
p00 |
||
|
uac-BarringTime |
s4 |
||
|
uac-BarringForAccessIdentity |
‘0000000’B |
||
|
} |
|||
|
} |
|||
|
uac-AccessCategory1-SelectionAssistanceInfo |
Not Present |
||
|
} |
|||
|
} |
|||
Table 11.3.2.3.3-2: SIB1 for NR Cell 1 (Step3, Table 11.3.2.3.2-1)
|
Derivation Path: TS 38.508-1 [4], Table 4.6.1-28 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
SIB1 ::= SEQUENCE { |
|||
|
uac-BarringInfo SEQUENCE { |
|||
|
uac-BarringForCommon SEQUENCE (SIZE (1..maxAccessCat-1)) OF UAC-BarringPerCat { |
8 entries |
||
|
UAC-BarringPerCat[1] SEQUENCE { |
entry 1 |
||
|
UAC-BarringPerCat[2] SEQUENCE { |
entry 2 |
||
|
accessCategory |
1 |
||
|
uac-barringInfoSetIndex |
1 |
||
|
} |
|||
|
UAC-BarringPerCat[3] SEQUENCE { |
entry 3 |
||
|
accessCategory |
2 |
||
|
uac-barringInfoSetIndex |
1 |
||
|
} |
|||
|
UAC-BarringPerCat[4] SEQUENCE { |
entry 4 |
||
|
accessCategory |
3 |
||
|
uac-barringInfoSetIndex |
1 |
||
|
} |
|||
|
UAC-BarringPerCat[5] SEQUENCE { |
entry 5 |
||
|
accessCategory |
4 |
||
|
uac-barringInfoSetIndex |
1 |
||
|
} |
|||
|
UAC-BarringPerCat[6] SEQUENCE { |
entry 6 |
||
|
accessCategory |
5 |
||
|
uac-barringInfoSetIndex |
1 |
||
|
} |
|||
|
UAC-BarringPerCat[7] SEQUENCE { |
entry 7 |
||
|
accessCategory |
6 |
||
|
uac-barringInfoSetIndex |
1 |
||
|
} |
|||
|
UAC-BarringPerCat[8] SEQUENCE { |
entry 8 |
||
|
accessCategory |
7 |
||
|
uac-barringInfoSetIndex |
1 |
||
|
} |
|||
|
} |
|||
|
uac-BarringPerPLMN-List |
Not present |
||
|
uac-BarringInfoSetList ::= SEQUENCE (SIZE(1..maxBarringInfoSet)) OF UAC-BarringInfoSet { |
1 entry |
||
|
UAC-BarringInfoSet[1] SEQUENCE { |
entry 1 |
||
|
uac-BarringFactor |
p00 |
||
|
uac-BarringTime |
s4 |
||
|
uac-BarringForAccessIdentity |
‘0000000’B |
||
|
} |
|||
|
} |
|||
|
uac-AccessCategory1-SelectionAssistanceInfo |
Not Present |
||
|
} |
|||
|
} |
|||
Table 11.3.2.3.3-3: RRCReject (step 16, table 11.3.2.3.2-1)
|
Derivation path: TS 38.508-1 [4] Table 4.6.1-15 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
RRCReject ::= SEQUENCE { |
|||
|
criticalExtensions CHOICE { |
|||
|
rrcReject SEQUENCE { |
|||
|
waitTime |
16 |
16 seconds |
|
|
} |
|||
|
} |
|||
|
} |
|||
Table 11.3.2.3.3-4: SERVICE REQUEST (step 21b2, Table 11.3.2.3.2-1)
|
Derivation Path: Table 4.7.1-16. |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Service type |
‘0100’B |
emergency services fallback |
||