6.2B.3 UE additional maximum output power reduction for EN-DC

38.101-33GPPNRPart 3: Range 1 and Range 2 Interworking operation with other radiosRelease 17TSUser Equipment (UE) radio transmission and reception

Tools: ARFCN - Frequency Conversion for 5G NR/LTE/UMTS/GSM

6.2B.3.1 Intra-band contiguous EN-DC

6.2B.3.1.0 General

For intra-band contiguous EN-DC band combinations with additional requirements the allowed A-MPR is specified in Table 6.2B.3.1.0-1 for UEs configured with EN-DC and combinations of network signalling values indicated in the E-UTRA and NR cell groups.

Unless otherwise stated the A-MPR specified in clause 6.2B.3.1 for intra-band contiguous EN-DC configurations is the total power reduction allowed including MPR.

Table 6.2B.3.1.0-1: Additional maximum power reduction for Intra-band contiguous EN-DC

DC configuration	Requirement (clause)	E-UTRA network signalling value	NR network signalling value	A-MPR (clause)
DC_(n)71AA	6.5B.2.1.2.1	NS_35	NS_35	6.2B.3.1.1³
DC_(n)41AA¹	6.5B.2.1.2.2 6.5B.4.1.1	NS_01 or NS_04	NS_04	6.2B.3.1.2⁴
NOTE 1: Only applies to UEs that support dual UL transmission for this EN-DC combination. NOTE 2: The additional emission requirement is indicated when the combination of network signalling values in the two CGs is set (only for UEs configured with EN-DC). NOTE 3: The A-MPR is applied as MPR if NS_35 is not signalled. NOTE 4: Void

6.2B.3.1.1 A-MPR for DC_(n)71AA

For UE supporting dynamic power sharing the following:

– for the MCG, A-MPR_c in accordance with TS 36.101 [4]

– for the SCG, A-MPR’_c = A-MPR_DC

– for the total configured transmission power, A-MPR_tot = A-MPR_DC

with A-MPR_DC as defined in this clause.

For UEs not supporting dynamic power sharing the following

– for the MCG,

A-MPR_c = A-MPR_E-UTRA

– for the SCG,

A-MPR’_c = A-MPR_NR

with A-MPR_E-UTRA and A-MPR_NR as defined in this clause.

For DC_(n)71AA with configured with network signaling values as per Table 6.2B.3.1.0-1 the allowed A-MPR is defined by

– for UE indicating support of dynamicPowerSharing in the UE-MRDC-Capability IE

A-MPR_DC = CEIL{ M_A,DC(A), 0.5}

where A-MPR_DC is the total power reduction allowed (dB),

– for OFDM:

M_A,DC = 11.00 – 11.67*A; 0.00 < A ≤ 0.30

8.10 – 2.00*A; 0.30 < A ≤ 0.80

6.50; 0.80 < A ≤ 1.00

– for DFT-S-OFDM:

M_A,DC = 11.00 – 13.33*A; 0.00 < A ≤ 0.30

8.00 – 3.33*A; 0.30 < A ≤ 0.60

6.00; 0.60 < A ≤ 1.00

where

with L_{CRB, E-UTRA} and N_{RB, E-UTRA}the number of allocated PRB and transmission bandwidth for MCG, L_CRB,NR and N_RB,NR the number of allocated PRB and transmission bandwidth for SCG with SCS = 15 kHz.

– for UE not indicating support of dynamicPowerSharing

A-MPR_E-UTRA = CEIL{ M_A,E-UTRA, 0.5}

A-MPR_NR = CEIL{ M_A,NR, 0.5}

where A-MPR is the total power reduction allowed per CG with

Where L_CRB,NR and N_RB,NRthe number of allocated PRB and transmission bandwidth for SCG with SCS = 15 kHz.

6.2B.3.1.2 A-MPR for NS_04

6.2B.3.1.2.0 General

When the UE is configured for B41/n41 intra-band contiguous EN-DC and it receives IE NS_04, the UE determines the total allowed maximum output power reduction as specified in this clause. The A-MPR for EN-DC defined in this clause is used instead of MPR defined in 6.2B.2.1, not additively, so EN-DC MPR = 0 when NS_04 is signaled. For UEs scheduled with single uplink transmission, AMPR in clause 6.2.4 of [4] and 6.2.3 of [2] apply.

For UE supporting dynamic power sharing the following:

– for the MCG, A-MPR_c in accordance with TS 36.101 [4]

– for the SCG,

A-MPR’_c = A-MPR_NR = MAX( A-MPR_single,NR, A-MPR_IM3)

– for the total configured transmission power,

A-MPR_tot = P_{PowerClass,EN-DC} – min(P_{PowerClass,EN-DC} ,10*log₁₀(10^((P_{PowerClass,E-UTRA}– A-MPR_E-UTRA)/10) + 10^((P_{PowerClass,NR}– A-MPR_NR)/10))

where

A-MPR_E-UTRA = MAX( A-MPR_{single,E-UTRA}+ MPR_{single,E-UTRA}, A-MPR_IM3)

with

– A-MPR_{single, E-UTRA}is the A-MPR defined for the E-UTRA transmission in TS 36.101 [4]

– A-MPR_single,NR is the A-MPR defined for the NR transmission in TS 38.101-1 [2]

– MPR_{single,E-UTRA} is the MPR defined for the E-UTRA transmission in TS 36.101 [4]

For UEs not supporting dynamic power sharing the following

– for the MCG,

A-MPR_c = MAX( A-MPR_{single, E-UTRA} + MPR_{single,E-UTRA}, A-MPR_IM3 )

– for the SCG,

A-MPR’_c = MAX( A-MPR_single,NR, A-MPR_IM3 )

where

– A-MPR_{single, E-UTRA}is the A-MPR defined for the E-UTRA transmission in TS 36.101 [4]

– A-MPR_single,NR is the A-MPR defined for the NR transmission in TS 38.101-1 [2]

– MPR_{single,E-UTRA} is the MPR defined for the E-UTRA transmission in TS 36.101 [4]

The UE determines the Allocation Configuration Case and the value of A-MPR_IM3 as follows:

If F_{IM3,low_block,low}< 2490.5 MHz

Allocation Configuration Case B. A-MPR_IM3 defined in Clause 6.2B.3.1.2.2

Else

Allocation Configuration Case A. A-MPR_IM3 defined in Clause 6.2B.3.1.2.1

where

– F_{IM3,low_block,low} = (2 * F_{low_alloc,low_edge}) – F_{high_alloc,high_edge}

– F_{low_alloc,low_edge}is the lowermost frequency of lower transmission bandwidth configuration.

– F_{high_alloc,high_edge}is the uppermost frequency of upper transmission bandwidth configuration.

Where the transmission bandwidth configuration for NR is the maximum frequency span covering all the configured SCSSpecificCarrier for scenarios that carrier bandwidths with different SCS can be fully overlapped.

NOTE: For non-dynamic power sharing capable UEs, since the allocation is unknown for one RAT, the edges of the channel transmission bandwidth are used instead of the edges of the RB allocations for that RAT.

6.2B.3.1.2.1 A-MPR_IM3 for NS_04 to meet -13 dBm / 1MHz

A-MPR is relative to 26 dBm for a power class 2 Cell Group to support PC1.5 and PC2 EN-DC UE. The same A-MPR is used relative to 23 dBm for a power class 3 Cell Group to support PC2 and PC3 EN-DC UE. The detail A-MPR values are decided based on the modified MPR behaviour in in Annex H.1. For the UE is configured with allocation configurations Case A or Case C (defined in Clause 6.2B.3.2.1), the allowed maximum output power reduction for IM3s applied to transmission on the MCG and the SCG with non-contiguous resource allocation is defined as follows:

A-MPR_IM3 = M_A

Where M_A is defined as follows

M_A = 12 ; 0 ≤ B < 0.54

10 ; 0.54 ≤ B < 1.08

9 ; 1.08 ≤ B < 2.16

8.5 ; 2.16 ≤ B < 3.24

8 ; 3.24 ≤ B < 5.4

6 ; 5.4 ≤ B

Where:

For UEs supporting dynamic power sharing,

B = (L_{CRB_alloc, E-UTRA}* 12* SCS_E-UTRA + L_{CRB_alloc,NR}* 12 * SCS_NR)/1,000,000

For UEs not supporting dynamic power sharing,

For E-UTRA

B = (L_{CRB_alloc, E-UTRA}* 12* SCS_E-UTRA + 12 * SCS_NR)/1,000,000

Where SCS_NR =15,000 Hz is assumed in calculation of B_.

For NR

B = (12* SCS_E-UTRA + L_{CRB_alloc,NR}* 12 * SCS_NR)/1,000,000

Where SCS_E-UTRA = 15,000 Hz is assumed in calculation of B.

and M_A is reduced by 1 dB for B < 2.0.

6.2B.3.1.2.2 A-MPR for NS_04 to meet -25 dBm / 1MHz

A-MPR is relative to 26 dBm for a power class 2 Cell Group to support PC1.5 and PC2 EN-DC UE. The same A-MPR is used relative to 23 dBm for a power class 3 Cell Group to support PC2 and PC3 EN-DC UE. The detail A-MPR values are decided based on the modified MPR behaviour in Annex H.1. For the UE is configured with allocation configurations Case B or Case D (defined in Clause 6.2B.3.2.1), the allowed maximum output power reduction for IM3s applied to transmission on the MCG and the SCG with non-contiguous resource allocation is defined as follows:

A-MPR_IM3 = M_A

Where M_A is defined as follows

M_A = 15 ; 0 ≤ B < 1.08

14 ; 1.08 ≤ B < 5.4

13 ; 5.4 ≤ B < 8.1

12 ; 8.1 ≤ B < 25.2

10 ; 25.2 ≤ B

Where:

For UEs supporting dynamic power sharing,

B = (L_{CRB_alloc, E-UTRA}* 12* SCS_E-UTRA + L_{CRB_alloc,NR}* 12 * SCS_NR)/ 1,000,000

For UEs not supporting dynamic power sharing,

For E-UTRA

B = (L_{CRB_alloc,E-UTRA}* 12* SCS_E-UTRA + 12 * SCS_NR)/1,000,000

Where SCS_NR =15,000 Hz is assumed in calculation of B.

For NR

B = (12* SCS_E-UTRA + L_{CRB_alloc,NR}* 12 * SCS_NR)/1,000,000

Where SCS_E-UTRA = 15,000 Hz is assumed in calculation of B.

and M_A is reduced by 1 dB.

6.2B.3.2 Intra-band non-contiguous EN-DC

6.2B.3.2.0 General

For intra-band non-contiguous EN-DC band combinations with additional requirements the A-MPR allowed are specified in Table 6.2B.3.2.0-1 for UEs configured with EN-DC and combinations of network signalling values indicated in the E-UTRA and NR cell group(s). Unless otherwise stated the A-MPR specified in clause 6.2B.3.2 for intra-band non-contiguous EN-DC configurations is the total power reduction allowed including MPR. For UEs scheduled with single uplink transmission, AMPR in clause 6.2.4 of [4] and 6.2.3 of [2] apply.

Table 6.2B.3.2.0-1: Allowed power reduction for intra-band non-contiguous EN-DC

DC configuration

Requirement (clause)

E-UTRA network signalling value

NR network signalling value

A-MPR (clause)

DC_41A_n41A¹

6.6.3.3.19 and 6.6.2.2.2 of TS 36.101 [4] and 6.5.2.3.2 and 6.5.3.3.1 of TS 38.101-1 [2]

NS_01 or NS_04

NS_04

6.2B.3.2.1

NOTE 1: Only applies to UEs that support dual UL transmission for this EN-DC combination.

NOTE 2: The requirement applies when the combination of network signalling values in the two CGs is set (only for UEs configured with EN-DC)..

6.2B.3.2.1 A-MPR for NS_04

When the UE is configured for B41/n41 intra-band non-contiguous EN-DC and it receives IE NS_04, the UE determines the total allowed maximum output power reduction as specified in this clause. The A-MPR for EN-DC defined in this clause is used instead of MPR defined in 6.2B.2.2, not additively, so EN-DC MPR=0 when NS_04 is signaled.

For UE supporting dynamic power sharing the following:

– for the MCG, A-MPR_c in accordance with TS 36.101 [4]

– for the SCG,

A-MPR’_c = A-MPR_NR = MAX( A-MPR_single,NR, A-MPR_EN-DC)

– for the total configured transmission power,

A-MPR_tot = P_{PowerClass,EN-DC} – min(P_{PowerClass,EN-DC} ,10*log₁₀(10^((P_{PowerClass,E-UTRA}– A-MPR_E-UTRA)/10) + 10^((P_{PowerClass,NR}– A-MPR_NR)/10))

where

A-MPR_E-UTRA = MAX( A-MPR_{single,E-UTRA}+ MPR_{single,E-UTRA}, A-MPR_EN-DC)

A-MPR_EN-DC= MAX(A-MPR_IM3, A-MPR_ACLRoverlap )

with

– A-MPR_{single, E-UTRA}is the A-MPR defined for the E-UTRA transmission in TS 36.101 [4]

– A-MPR_single,NR is the A-MPR defined for the NR transmission in TS 38.101-1 [2]

– MPR_{single,E-UTRA} is the MPR defined for the E-UTRA transmission in TS 36.101 [4]

For UEs not supporting dynamic power sharing the following

– for the MCG,

A-MPR_c = MAX( A-MPR_{single, E-UTRA} + MPR_{single,E-UTRA}, A-MPR_IM3, A-MPR_ACLRoverlap)

– for the SCG,

A-MPR’_c = MAX( A-MPR_single,NR, A-MPR_IM3, A-MPR_ACLRoverlap)

where

– A-MPR_{single, E-UTRA}is the A-MPR defined for the E-UTRA transmission in TS 36.101 [4]

– A-MPR_single,NR is the A-MPR defined for the NR transmission in TS 38.101-1 [2]

– MPR_{single,E-UTRA} is the MPR defined for the E-UTRA transmission in TS 36.101 [4]

The UE determines the Allocation Configuration Case and the value of A-MPR_IM3 as follows:

If AND( F_{IM3,low_block,high}< F_{filter,low ,}MAX( SEM_-13,high, F_{IM3,high_block,low} ) > F_filter,high)

Allocation Configuration Case C. A-MPR_IM3 defined in Clause 6.2B.3.1.2.1

Else

Allocation Configuration Case D. A-MPR_IM3 defined in Clause 6.2B.3.1.2.2

where

– F_{IM3,low_block,high}=(2 * F_{low_alloc,high_edge} ) – F_{high_alloc,low_edge}

– F_{IM3,high_block,low} = (2 * F_{high_alloc,low_edge}) – F_{low_alloc,high_edge}

– F_{low_alloc,low_edge}is the lowermost frequency of lower transmission bandwidth allocation.

– F_{low_alloc,high_edge}is the uppermost frequency of lower transmission bandwidth allocation.

– F_{high_alloc,low_edge}is the lowermost frequency of upper transmission bandwidth allocation.

– F_{high_alloc,high_edge}is the uppermost frequency of upper transmission bandwidth allocation.

– F_filter,low = 2480 MHz

– F_filter,high = 2745 MHz

– SEM_-13,high = Threshold frequency where upper spectral emission mask for upper channel drops from -13 dBm / 1MHz to -25 dBm / 1MHz, as specified in Clause6.6.2.2.2 in [4] and Clause 6.5.2.3.2 in [2] respectively.

The UE determines the value of A-MPR_ACLRoverlap as specified in Table 6.2B.3.2.1-1:

Table 6.2B.3.2.1-1: A-MPR_ACLRoverlap

W_gap	A-MPR_ACLRoverlap
< BW_{channel,E-UTRA} + BW_channel,NR	4 dB
≥ BW_{channel,E-UTRA} + BW_channel,NR	0 dB
NOTE 1: W_gap = F_{high_channel,low_edge –} F_{low_channel,high_edge}

6.2B.3.3 Inter-band EN-DC within FR1

For inter-band EN-DC between E-UTRA and FR1 NR, UE additional maximum output power reduction specified in TS 36.101 [4] and TS 38.101-1 [2] apply for E-UTRA and NR respectively.

Unless specified in Table 6.2B.3.3-1, for inter-band carrier aggregation with uplink assigned to LTE and NR bands, the requirements in [2] clause 6.2.3 apply for NR uplink component carrier and the requirements in [4] clause 6.2.4 apply for LTE uplink component carrier.

Unless otherwise stated, for inter-band EN-DC with uplink assigned to LTE and NR bands and specified in Table 6.2B.3.3-1, the combined requirements and allowed A-MPR are applibale on both LTE and NR bands when LTE and NR component carriers are active. The requirements in Table 6.2B.3.3-1 are specified in terms of an additional spectrum emission requirement. The emission requirements specified in Table 6.2B.3.3-1 also apply for the frequency ranges that are less than F_OOB (MHz) from the edge of the channel bandwidth specified in TS 36.101 [4] and TS 38.101-1 [2], respectively.

Table 6.2B.3.3-1: Additional Requirements for inter-band EN-DC (two-bands)

NR CA combination	Band	Applied NS	Requirements (clause) (TS 36.101 [4])	Requirements (clause) (TS 38.101-1 [2])	A-MPR (table/clause) (TS 36.101 [4])	A-MPR (table/clause) (TS 38.101-1 [2])	Note
DC_1_n3	1	05	6.6.3.3.1	6.6.3.3.1	Table 6.2.4-1 (NS_05)	N/A	1
DC_1_n3	n3	100	N/A	6.5.2.4.2	N/A	Table 6.2.3.1-2	1
DC_1_n5	1	05	6.6.3.3.1	N/A	Table 6.2.4-1 (NS_05)	N/A	1
DC_1_n5	n5	100	N/A	6.5.2.4.2	N/A	Table 6.2.3.1-2	1
DC_1_n8	1	05	6.6.3.3.1	N/A	Table 6.2.4-1 (NS_05)	N/A	1
	n8	43	N/A	6.5.3.3.5	N/A	Clause 6.2.3.6
	n8	43U	N/A	6.5.3.3.5, 6.5.2.4.2	N/A	Clause 6.2.3.6
DC_1_n28	1	05	6.6.3.3.1	N/A	Table 6.2.4-1 (NS_05)	N/A	2
DC_1_n28	n28	17	N/A	6.5.3.3.2	N/A	N/A	2
DC_1_n40	1	05	6.6.3.3.1	N/A	Table 6.2.4-1 (NS_05)	N/A
DC_1_n41	1	05	6.6.3.3.1	N/A	Table 6.2.4-1 (NS_05)	N/A
DC_1_n41	n41	47	N/A	6.5.3.3.15	N/A	Table 6.2.3.18-2
DC_1_n77 DC_1_n84_ULSUP-TDM_n77	1	05	6.6.3.3.1	N/A	Table 6.2.4-1 (NS_05)	N/A	1
	n84	05	N/A	6.5.3.3.4	N/A	Clause 6.2.3.4
	n84	05U	N/A	6.5.3.3.4	N/A	Clause 6.2.3.4
DC_1_n78 DC_1_n84_ULSUP-TDM_n78	1	05	6.6.3.3.1	N/A	Table 6.2.4-1 (NS_05)	N/A	1
	n84	05	N/A	6.5.3.3.4	N/A	Clause 6.2.3.4
	n84	05U	N/A	6.5.3.3.4, 6.5.2.4.2	N/A	Clause 6.2.3.4
DC_1_n79 DC_1_n84_ULSUP-TDM_n79	1	05	6.6.3.3.1	N/A	Table 6.2.4-1 (NS_05)	N/A	1
	n84	05	N/A	6.5.3.3.4	N/A	Clause 6.2.3.4
	n84	05U	N/A	6.5.3.3.4, 6.5.2.4.2	N/A	Clause 6.2.3.4
DC_3_n1	n1	05	N/A	6.5.3.3.4	N/A	Clause 6.2.3.4	1
DC_3_n1	n1	05U	N/A	6.5.3.3.4, 6.5.2.4.2	N/A	Clause 6.2.3.4	1
DC_3_n5	n5	100	N/A	6.5.2.4.2	N/A	Table 6.2.3.1-2	1
DC_3_n8	n8	43	N/A	6.5.3.3.5	N/A	Clause 6.2.3.6	1
DC_3_n8	n8	43U	N/A	6.5.3.3.5	N/A	Clause 6.2.3.6	1
DC_3_n28	n28	17	N/A	6.5.3.3.2	N/A	N/A	2
DC_3_n41, DC_3_n80_ULSUP-TDM_n41	n41	47	N/A	6.5.3.3.15	N/A	Table 6.2.3.18-2	1
DC_3_n41, DC_3_n80_ULSUP-TDM_n41	n80	100	N/A	6.5.2.4.2	N/A	Table 6.2.3.1-2	1
DC_8_n1	n1	05	N/A	6.5.3.3.4	N/A	Clause 6.2.3.4	1, 3
DC_8_n1	n1	05U	N/A	6.5.3.3.4, 6.5.2.4.2	N/A	Clause 6.2.3.4	1, 3
DC_8_n3	n3	100	N/A	6.5.2.4.2	N/A	Table 6.2.3.1-2	1, 3
DC_8_n28	n28	17	N/A	6.5.3.3.2	N/A	N/A	2, 3
DC_8_n41, DC_8_n81_ULSUP-TDM_n41	n41	47	N/A	6.5.3.3.15	N/A	Table 6.2.3.18-2	3
	n81	43	N/A	6.5.3.3.5	N/A	Clause 6.2.3.6
	n81	43U	N/A	6.5.3.3.5	N/A	Clause 6.2.3.6
DC_11_n3	n3	100	N/A	6.5.2.4.2	N/A	Table 6.2.3.1-2	1
DC_11_n28	n28	17	N/A	6.5.3.3.2	N/A	N/A	2
DC_11_n41	n41	47	N/A	6.5.3.3.15	N/A	Table 6.2.3.18-2
DC_18_n3	n3	100	N/A	6.5.2.4.2	N/A	Table 6.2.3.1-2	1
DC_18_n28	n28	17	N/A	6.5.3.3.2	N/A	N/A	2
DC_19_n1	19	08	6.6.3.3.3	N/A	Table 6.2.4-1 (NS_08)	N/A	1
	n1	05	N/A	6.5.3.3.4	N/A	Clause 6.2.3.4
	n1	05U	N/A	6.5.3.3.4, 6.5.2.4.2	N/A	Clause 6.2.3.4
DC_19_n77	19	08	6.6.3.3.3	N/A	Table 6.2.4-1 (NS_08)	N/A
DC_19_n78	19	08	6.6.3.3.3	N/A	Table 6.2.4-1 (NS_08)	N/A
DC_19_n79	19	08	6.6.3.3.3	N/A	Table 6.2.4-1 (NS_08)	N/A
DC_21_n1	21	09	6.6.3.3.4	N/A	Table 6.2.4-1 (NS_08)	N/A	1
	n1	05	N/A	6.5.3.3.4	N/A	Clause 6.2.3.4
	n1	05U	N/A	6.5.3.3.4, 6.5.2.4.2	N/A	Clause 6.2.3.4
DC_21_n28	21	09	6.6.3.3.4	N/A	Table 6.2.4-1 (NS_09)		2
DC_21_n28	n28	17	N/A	6.5.3.3.2	N/A	N/A	2
DC_21_n77	21	09	6.6.3.3.4	N/A	Table 6.2.4-1 (NS_09)	N/A
DC_21_n78	21	09	6.6.3.3.4	N/A	Table 6.2.4-1 (NS_09)	N/A
DC_21_n79	21	09	6.6.3.3.4	N/A	Table 6.2.4-1 (NS_09)	N/A
DC_28_n1	28	17	6.6.3.3.10	N/A	Table 6.2.4-1 (NS_17)	N/A	1, 2
	n1	05	N/A	6.5.3.3.4	N/A	Clause 6.2.3.4
	n1	05U	N/A	6.5.3.3.4, 6.5.2.4.2	N/A	Clause 6.2.3.4
DC_28_n3	28	17	6.6.3.3.10	N/A	Table 6.2.4-1 (NS_17)	N/A	2
DC_28_n3	n3	100	N/A	6.5.2.4.2	N/A	Table 6.2.3.1-2	2
DC_28_n5	28	17	6.6.3.3.10	N/A	Table 6.2.4-1 (NS_17)	N/A	1, 2
DC_28_n5	n5	100	N/A	6.5.2.4.2	N/A	Table 6.2.3.1-2	1, 2
DC_28_n8	28	17	6.6.3.3.10	N/A	Table 6.2.4-1 (NS_17)	Table 6.2.4-1 (NS_17)	1, 2
	n8	43	N/A	6.5.3.3.5	N/A	Clause 6.2.3.6
	n8	43U	N/A	6.5.3.3.5	N/A	Clause 6.2.3.6
DC_28_n40	28	17	6.6.3.3.10	N/A	Table 6.2.4-1 (NS_17)	N/A	2
DC_28_n41	28	17	6.6.3.3.10	N/A	Table 6.2.4-1 (NS_17)	N/A	2
DC_28_n41	n41	47	N/A	6.5.3.3.15	N/A	Table 6.2.3.18-2	2
DC_28_n77	28	17	6.6.3.3.10	N/A	Table 6.2.4-1 (NS_17)	N/A	2
DC_28_n78	28	17	6.6.3.3.10	N/A	Table 6.2.4-1 (NS_17)	N/A	2
DC_28_n79	28	17	6.6.3.3.10	N/A	Table 6.2.4-1 (NS_17)	N/A	2
DC_40_n1	n1	05	N/A	6.5.3.3.4	N/A	Clause 6.2.3.4	1
DC_40_n1	n1	05U	N/A	6.5.3.3.4, 6.5.2.4.2	N/A	Clause 6.2.3.4	1
DC_40_n41	n41	47	N/A	6.5.3.3.15	N/A	Table 6.2.3.18-2
DC_41_n3	n3	100	N/A	6.5.2.4.2	N/A	Table 6.2.3.1-2	1
DC_41_n28	n28	17	N/A	6.5.3.3.2	N/A	N/A	2
DC_42_n1	n1	05	N/A	6.5.3.3.4	N/A	Clause 6.2.3.4	1
DC_42_n1	n1	05U	N/A	6.5.3.3.4, 6.5.2.4.2	N/A	Clause 6.2.3.4	1
DC_42_n3	n3	100	N/A	6.5.2.4.2	N/A	Table 6.2.3.1-2	1
DC_42_n28	n28	17	N/A	6.5.3.3.2	N/A	N/A	2
NOTE 1: NS_05U, NS_43U and NS_100 can be signalled for NR bands that have UTRA services deployed and protected range is specified in clause 6.5.2.4.2 of TS38.101-1[2] and the requirements in clause 6.5.2.4.2 are only appliable to the signalling band. NOTE 2: Applicable when the assigned NR carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz. NOTE 3: This requirement is applicable only for the following cases: A: for carriers of 5 MHz channel bandwidth when carrier centre frequency (Fc) is within the range 902.5 MHz ≤ Fc < 907.5 MHz with an uplink transmission bandwidth less than or equal to 20 RB; B: for carriers of 5 MHz channel bandwidth when carrier centre frequency (Fc) is within the range 907.5 MHz ≤ Fc ≤ 912.5 MHz without any restriction on uplink transmission bandwidth; C: for carriers of 10 MHz channel bandwidth when carrier centre frequency (Fc) is Fc = 910 MHz with an uplink transmission bandwidth less than or equal to 32 RB with RB_start > 3.

6.2B.3.3A Inter-band NE-DC within FR1

For inter-band NE-DC between E-UTRA and FR1 NR, UE additional maximum output power reduction specified in TS 36.101 [4] and TS 38.101-1 [2] apply for E-UTRA and NR respectively.

Unless specified in Table 6.2B.3.3A-1, for inter-band carrier aggregation with uplink assigned to LTE and NR bands, the requirements in [2] clause 6.2.3 apply for NR uplink component carrier and the requirements in [4] clause 6.2.4 apply for LTE uplink component carrier.

Unless otherwise stated, for inter-band EN-DC with uplink assigned to LTE and NR bands and specified in Table 6.2B.3.3A-1, the combined requirements and allowed A-MPR are applibale on both LTE and NR bands when LTE and NR component carriers are active. The requirements in Table 6.2B.3.3A-1 are specified in terms of an additional spectrum emission requirement. The emission requirements specified in Table 6.2B.3.3A-1 also apply for the frequency ranges that are less than F_OOB (MHz) from the edge of the channel bandwidth specified in TS 36.101 [4] and TS 38.101-1 [2], respectively.

Table 6.2B.3.3A-1: Additional Requirements for inter-band NE-DC (two-bands)

NR CA combination	Band	Applied NS	Requirements (clause) (TS 36.101 [4])	Requirements (clause) (TS 38.101-1 [2])	A-MPR (table/clause) (TS 36.101 [4])	A-MPR (table/clause) (TS 38.101-1 [2])	Note
DC_n1_28	n1	05	N/A	6.5.3.3.4	N/A	Clause 6.2.3.4	1, 2
	n1	05U	N/A	6.5.3.3.4, 6.5.2.4.2	N/A	Clause 6.2.3.4
	28	17	6.6.3.3.10	N/A	Table 6.2.4-1 (NS_17)	N/A
DC_n78_1	1	05	6.6.3.3.1	N/A	Table 6.2.4-1 (NS_05)	N/A
NOTE 1: NS_05U can be signalled for NR bands that have UTRA services deployed and protected range is specified in clause 6.5.2.4.2 of TS38.101-1[2] and the requirements in clause 6.5.2.4.2 are only appliable to the signalling band. NOTE 2: Applicable when the assigned NR carrier is confined within 718 MHz and 748 MHz and when the channel bandwidth used is 5 or 10 MHz.

6.2B.3.4 Inter-band EN-DC including FR2

UE additional maximum output power reduction requirement for E-UTRA single carrier and CA operation specified in clauses 6.2.4 and 6.2.4A of TS 36.101 [4] and for NR single carrier and CA operation specified in clause 6.2.3, 6.2A.3 and 6.2D.3 of TS 38.101-2 [3] apply.