7.5 RRC Protocol Procedures
37.571-23GPPPart 2: Protocol conformanceRelease 16TSUser Equipment (UE) conformance specification for UE positioning
7.5.1 Inter-frequency RSTD measurement indication
7.5.1.1 Test Purpose (TP)
(1)
with { a NAS signalling connection existing }
ensure that {
when { the UE receives OTDOA assistance data including inter-frequency cells together with
a location request for OTDOA }
then { the UE initiates the RRC Inter-frequency RSTD measurement procedure to indicate
“start”.}
}
(2)
with { a NAS signalling connection existing }
ensure that {
when { the UE stops reporting inter-frequency RSTD measurements }
then { the UE initiates the RRC Inter-frequency RSTD measurement procedure to indicate
“stop”. }
}
7.5.1.2 Conformance requirements
References: The conformance requirements covered in the present TC are specified in: TS 36.355 clauses 6.5.1.2, 6.5.1.5, and TS 36.331 clauses 5.5.7.2, 5.7.7.3.
[TS 36.355, clause 6.5.1.2]
If inter-frequency neighbour cells are included in OTDOA-NeighbourCellInfoList, where an inter-frequency is a E-UTRA frequency which is different from the E-UTRA serving cell frequency, the LPP layer shall inform lower layers to start performing inter-frequency RSTD measurements for these neighbour cells and also provide to lower layers the information about these neighbour cells, e.g. EARFCN and PRS positioning occasion information.
[TS 36.355, clause 6.5.1.5]
If the target device stops reporting inter-frequency RSTD measurements, where the inter-frequency RSTD measurement is an OTDOA RSTD measurement with at least one cell on a frequency different from the serving cell frequency, the LPP layer shall inform lower layers that inter-frequency RSTD measurements are stopped.
[TS 36.331, clause 5.5.7.2]
The UE shall:
1> if and only if upper layers indicate to start performing inter-frequency RSTD measurements; and the UE requires measurement gaps for these measurements while measurement gaps are either not configured or not sufficient:
2> initiate the procedure to indicate start;
NOTE 1: The UE verifies the measurement gap situation only upon receiving the indication from upper layers. If at this point in time sufficient gaps are available, the UE does not initiate the procedure. Unless it receives a new indication from upper layers, the UE is only allowed to further repeat the procedure in the same PCell once per frequency if the provided measurement gaps are insufficient.
1> if and only if upper layers indicate to stop performing inter-frequency RSTD measurements:
2> initiate the procedure to indicate stop;
NOTE 2: The UE may initiate the procedure to indicate stop even if it did not previously initiate the procedure to indicate start.
[TS 36.331, clause 5.5.7.3]
The UE shall set the contents of InterFreqRSTDMeasurementIndication message as follows:
1> set the rstd-InterFreqIndication as follows:
2> if the procedure is initiated to indicate start of inter-frequency RSTD measurements:
3> set the rstd-InterFreqInfoList according to the information received from upper layers;
2> else if the procedure is initiated to indicate stop of inter-frequency RSTD measurements:
3> set the rstd-InterFreqIndication to the value stop;
1> submit the InterFreqRSTDMeasurementIndication message to lower layers for transmission, upon which the procedure ends;
7.5.1.3 Test description
7.5.1.3.1 Pre-test conditions
System Simulator:
– Cell 1 as specified in 5.2.2.
UE:
–
Preamble:
– The UE is in state Generic RB Established (state 3) according to 3GPP 36.508 [8] (no measurement gaps are configured).
Related PICS/PIXIT Statements:
– Support for inter-frequency RSTD measurements that require measurement gaps for these measurements.
7.5.1.3.2 Test procedure sequence
Table 7.5.1.3.2-1: Main behaviour
|
St |
Procedure |
Message Sequence |
TP |
Verdict |
|
|
U – S |
Message |
||||
|
1 |
The stored OTDOA assistance data in the UE are cleared. |
<– |
RESET UE POSITIONING STORED INFORMATION |
– |
– |
|
1a |
The SS sends a LPP message of type Request Capabilities. |
<– |
DLInformationTransfer (LPP REQUEST CAPABILITIES) |
– |
– |
|
1b |
The UE sends a LPP message of type Provide Capabilities including the UE positioning capabilities. |
–> |
ULInformationTransfer (LPP PROVIDE CAPABILITIES) |
– |
– |
|
1c |
IF the UE LPP message at step 1b includes an acknowledgment request THEN SS sends a LPP Acknowledgement response. |
<– |
DLInformationTransfer (LPP ACKNOWLEDGEMENT) |
– |
– |
|
– |
EXCEPTION: In parallel to the events described in Steps 2 to 6, the steps specified in Table 7.5.1.3.2-2 take place |
||||
|
2 |
The SS sends a LPP message of type Provide Assistance Data. |
<– |
DLInformationTransfer (LPP PROVIDE ASSISTANCE DATA) |
– |
– |
|
3-5 |
Void |
||||
|
6 |
The SS sends a LPP message of type Request Location Information including a request for OTDOA location measurements. |
<– |
DLInformationTransfer (LPP REQUEST LOCATION INFORMATION) |
– |
– |
|
– |
EXCEPTION: In parallel with the events described in Steps 7 to 10, the steps specified in Table 7.5.1.3.2-3 take place. |
||||
|
7 |
The UE sends a LPP message of type Provide Location Information. |
–> |
ULInformationTransfer (LPP PROVIDE LOCATION INFORMATION) |
– |
– |
|
7a |
IF the UE LPP message at step 7 includes an acknowledgment request THEN SS sends a LPP Acknowledgement response. |
<– |
DLInformationTransfer (LPP ACKNOWLEDGEMENT) |
– |
– |
|
8-10 |
Void |
||||
Table 7.5.1.3.2-2: Parallel behaviour
|
St |
Procedure |
Message Sequence |
TP |
Verdict |
|
|
U – S |
Message |
||||
|
1 |
The UE transmits an RRC InterFreqRSTDMeasurementIndication message to indicate “start” |
–> |
InterFreqRSTDMeasurementIndication |
1 |
P |
|
2 |
The SS transmits an RRCConnectionReconfiguration message to set up the measurement gap configuration |
<– |
RRCConnectionReconfiguration |
– |
– |
|
3 |
The UE transmits an RRCConnectionReconfigurationComplete message to confirm the set up of the measurement gap configuration |
–> |
RRCConnectionReconfigurationComplete |
– |
– |
Table 7.5.1.3.2-3: Parallel behaviour
|
St |
Procedure |
Message Sequence |
TP |
Verdict |
|
|
U – S |
Message |
||||
|
1 |
The UE transmits an RRC InterFreqRSTDMeasurementIndication message to indicate “stop” |
–> |
InterFreqRSTDMeasurementIndication |
2 |
P |
|
2 |
The SS transmits an RRCConnectionReconfiguration message to release the measurement gap configuration |
<– |
RRCConnectionReconfiguration |
– |
– |
|
3 |
The UE transmits an RRCConnectionReconfigurationComplete message to confirm the release of the measurement gap configuration |
–> |
RRCConnectionReconfigurationComplete |
– |
– |
7.5.1.3.3 Specific message contents
For the default message content as specified in subclause 5.4, the values for sub-test 5 are used.
Table 7.5.1.3.3-1: RESET UE POSITIONING STORED INFORMATION (step 1, Table 7.5.1.3.2-1)
|
Derivation Path: 36.509 clause 6.9 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
UE Positioning Technology |
0 0 0 0 0 0 0 1 |
OTDOA |
||
Table 7.5.1.3.3-2: DLInformationTransfer (steps 1a, 1c, 2, 6 and 7a, Table 7.5.1.3.2-1)
|
Derivation Path: 36.331 clause 6.2.2 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
DLInformationTransfer ::= SEQUENCE { |
||||
|
rrc-TransactionIdentifier |
||||
|
criticalExtensions CHOICE { |
||||
|
c1 CHOICE { |
||||
|
dlInformationTransfer-r8 SEQUENCE { |
||||
|
dedicatedInfoType CHOICE { |
||||
|
dedicatedInfoNAS OCTET STRING |
Set according to Table 7.5.1.3.3-3 |
DOWNLINK GENERIC NAS TRANSPORT |
||
|
} |
||||
|
nonCriticalExtension SEQUENCE {} |
Not present |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
Table 7.5.1.3.3-3: DOWNLINK GENERIC NAS TRANSPORT (steps 1a, 1c, 2, 6 and 7a, Table 7.5.1.3.2-1)
|
Derivation Path: 24.301 Table 8.2.31.1 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Protocol discriminator |
0111 |
EPS mobility management messages |
||
|
Security header type |
0000 |
Plain NAS message |
||
|
Downlink generic NAS transport message identity |
01101000 |
Downlink generic NAS transport |
||
|
Generic message container type |
00000001 |
LTE Positioning Protocol (LPP) message container |
||
|
Generic message container |
Step 1a: Set according to Table 7.5.1.3.3-3a |
LPP Request Capabilities. |
||
|
Step 2: Set according to Table 7.5.1.3.3-4 |
LPP Provide Assistance Data |
|||
|
Step 6: Set according to Table 7.5.1.3.3-8 |
LPP Request Location Information |
|||
|
Steps 1c and 7a: Set according to Table 7.5.1.3.3-12 |
LPP Acknowledgement |
|||
|
Additional information |
Present |
Routing Identifier/ Correlation ID |
||
Table 7.5.1.3.3-3a: LPP Request Capabilities (step 1a, Table 7.5.1.3.2-1)
|
Derivation Path: Table 5.4-1 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
As defined in Table 5.4-1 |
||||
Table 7.5.1.3.3-4: LPP Provide Assistance data (step 2, Table 7.5.1.3.2-1)
|
Derivation Path: Table 5.4-2 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
As defined in Table 5.4-2 with the following exceptions: |
||||
|
transactionID SEQUENCE { |
||||
|
initiator |
locationServer |
|||
|
transactionNumber |
(0..255) |
|||
|
} |
||||
|
otdoa-ProvideAssistanceData SEQUENCE { |
||||
|
otdoa-NeighbourCellInfo |
Set according to Table 7.5.1.3.3-5. |
|||
|
} |
||||
Table 7.5.1.3.3-5: OTDOA-NeighbourCellInfoList (step 2, Table 7.5.1.3.2-1)
|
Derivation Path: 36.355 clause 6.5.1.2 |
|||
|
Information Element |
Value/remark |
Comment |
Condition |
|
OTDOA-NeighbourCellInfoList ::= SEQUENCE (SIZE(2)) OF SEQUENCE { |
|||
|
SEQUENCE (SIZE(1)) OF SEQUENCE { |
Cell 3 |
||
|
physCellId |
3 |
||
|
cellGlobalId SEQUENCE { |
|||
|
mcc |
As defined for Cell 3 in 36.508 [8] |
||
|
mnc |
As defined for Cell 3 in 36.508 [8] |
||
|
cellidentity |
As defined for Cell 3 in 36.508 [8] |
||
|
} |
|||
|
earfcn |
For E-UTRA band < 65: as defined for Cell 3 in 36.508 [8] For E-UTRA band > 64: not present |
||
|
cpLength |
Not present |
Same as for the reference cell |
|
|
prsInfo SEQUENCE { |
|||
|
prs-Bandwidth |
PRS are transmitted over the used system bandwidth (see subclause 5.2.2) |
||
|
prs-ConfigurationIndex |
12 |
||
|
numDL-Frames |
sf-1 |
||
|
prs-MutingInfo-r9 |
Not present |
PRS muting is not used. |
|
|
prsID-r14 |
Not present |
PRS-ID not used |
Rel-14 onwards |
|
add-numDL-Frames-r14 |
Not present |
Not required |
Rel-14 onwards |
|
prsOccGroupLen-r14 |
Not present |
No PRS occasion group configured |
Rel-14 onwards |
|
prsHoppingInfo-r14 |
Not present |
PRS frequency hopping not used |
Rel-14 onwards |
|
} |
|||
|
antennaPortConfig |
Not present |
Same as for the reference cell |
|
|
slotNumberOffset |
Not present |
Slot timing is the same as for reference cell |
|
|
prs-SubframeOffset |
10 |
||
|
expectedRSTD |
8192 |
Value 0 |
|
|
expectedRSTD-Uncertainty |
10 |
About 1 s |
|
|
earfcn-v9a0 |
For E-UTRA band < 65: not present For E-UTRA Band > 64: as defined for Cell 3 in 36.508 [8] |
||
|
tpId-r14 |
Not present |
Transmission Points not used |
Rel-14 onwards |
|
prs-only-tp-r14 |
Not present |
Not required |
Rel-14 onwards |
|
cpLengthCRS-r14 |
Normal |
Rel-14 onwards |
|
|
sameMBSFNconfigNeighbour-r14 |
TRUE |
Same as for the reference cell |
Rel-14 onwards |
|
dlBandwidth-r14 |
Not present |
Same as for the reference cell and PRS frequency hopping not used |
Rel-14 onwards |
|
addPRSconfigNeighbour-r14 |
Not present |
No additional PRS configuration(s) |
Rel-14 onwards |
|
} |
|||
|
SEQUENCE (SIZE(1)) OF SEQUENCE { |
Cell 6 |
Assumes that earfcn for Cell 6 is different from earfcn for Cell 3. |
|
|
physCellId |
6 |
||
|
cellGlobalId SEQUENCE { |
|||
|
mcc |
As defined for Cell 6 in 36.508 [8] |
||
|
mnc |
As defined for Cell 6 in 36.508 [8] |
||
|
cellidentity |
As defined for Cell 6 in 36.508 [8] |
||
|
} |
|||
|
earfcn |
For E-UTRA band < 65: For E-UTRA band > 64: not present |
||
|
cpLength |
Not present |
Same as for the reference cell |
|
|
prsInfo SEQUENCE { |
|||
|
prs-Bandwidth |
PRS are transmitted over the used system bandwidth (see subclause 5.2.2) |
||
|
prs-ConfigurationIndex |
12 |
||
|
numDL-Frames |
sf-1 |
||
|
prs-MutingInfo-r9 |
Not present |
PRS muting is not used. |
|
|
prsID-r14 |
Not present |
PRS-ID not used |
Rel-14 onwards |
|
add-numDL-Frames-r14 |
Not present |
Not required |
Rel-14 onwards |
|
prsOccGroupLen-r14 |
Not present |
No PRS occasion group configured |
Rel-14 onwards |
|
prsHoppingInfo-r14 |
Not present |
PRS frequency hopping not used |
Rel-14 onwards |
|
} |
|||
|
antennaPortConfig |
Not present |
Same as for the reference cell |
|
|
slotNumberOffset |
Not present |
Slot timing is the same as for reference cell |
|
|
prs-SubframeOffset |
10 |
||
|
expectedRSTD |
8192 |
Value 0 |
|
|
expectedRSTD-Uncertainty |
10 |
About 1 s |
|
|
earfcn-v9a0 |
For E-UTRA band < 65: not present For E-UTRA band > 64: as defined for Cell 6 in 36.508 [8] |
||
|
tpId-r14 |
Not present |
Transmission Points not used |
Rel-14 onwards |
|
prs-only-tp-r14 |
Not present |
Not required |
Rel-14 onwards |
|
cpLengthCRS-r14 |
Normal |
Rel-14 onwards |
|
|
sameMBSFNconfigNeighbour-r14 |
TRUE |
Same as for the reference cell |
Rel-14 onwards |
|
dlBandwidth-r14 |
Not present |
Same as for the reference cell and PRS frequency hopping not used |
Rel-14 onwards |
|
addPRSconfigNeighbour-r14 |
Not present |
No additional PRS configuration(s) |
Rel-14 onwards |
|
} |
|||
|
} |
|||
Table 7.5.1.3.3-6: RRC InterFreqRSTDMeasurementIndication (step 1, Table 7.5.1.3.2-2)
|
Derivation Path: 36.331, clause 6.2.2 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
InterFreqRSTDMeasurementIndication-r10 ::= SEQUENCE{ |
||||
|
criticalExtensions CHOICE { |
||||
|
c1 CHOICE { |
||||
|
interFreqRSTDMeasurementIndication-r10 SEQUENCE { |
||||
|
rstd-InterFreqIndication-r10 CHOICE { |
||||
|
start SEQUENCE { |
||||
|
rstd-InterFreqInfoList-r10 SEQUENCE { |
2 entries |
|||
|
carrierFreq-r10[1] |
For E-UTRA band < 65: as defined for Cell 3 in 36.508 [8] For E-UTRA band > 64: 65535 |
|||
|
measPRS-Offset-r10[1] |
(0..39) |
|||
|
carrierFreq-v1090[1] |
For E-UTRA band < 65: not present For E-UTRA band > 64: as defined for Cell 3 in 36.508 [8] |
|||
|
carrierFreq-r10[2] |
For E-UTRA band < 65: as defined for Cell 6 in 36.508 [8] For E-UTRA band > 64: 65535 |
|||
|
measPRS-Offset-r10[2] |
(0..39) |
|||
|
carrierFreq-v1090[2] |
For E-UTRA band < 65: Not present For E-UTRA band > 64: as defined for Cell 6 in 36.508 [8] |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
lateNonCriticalExtension OCTET STRING |
Not present |
|||
|
nonCriticalExtension SEQUENCE {} |
Not present |
|||
|
} |
||||
|
criticalExtensionsFuture SEQUENCE {} |
Not present |
|||
|
} |
||||
|
} |
||||
|
} |
||||
Table 7.5.1.3.3-7: RRCConnectionReconfiguration (step 2, Table 7.5.1.3.2-2)
|
Derivation Path: 36.508, Table 4.6.1-8 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
As defined in 36.508, Table 4.6.1-8 with the following exceptions: |
||||
|
measConfig ::= SEQUENCE { |
||||
|
measGapConfig CHOICE { |
||||
|
setup SEQUENCE { |
||||
|
gapOffset CHOICE { |
||||
|
gp0 |
Value of measPRS-Offset-r10 as provided by the UE in Table 7.5.1.3.3-6. |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
Table 7.5.1.3.3-8: LPP Request Location Information (step 6, Table 7.5.1.3.2-1)
|
Derivation Path: Table 5.4-3 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
As defined in Table 5.4-3 with the following exceptions: |
||||
|
locationInformationType |
locationMeasurementsRequired |
|||
|
time |
10 |
|||
Table 7.5.1.3.3-9: ULInformationTransfer (steps 1b and 7, Table 7.5.1.3.2-1)
|
Derivation Path: 36.331 clause 6.2.2 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
ULInformationTransfer ::= SEQUENCE { |
||||
|
criticalExtensions CHOICE { |
||||
|
c1 CHOICE { |
||||
|
ulInformationTransfer-r8 SEQUENCE { |
||||
|
dedicatedInfoType CHOICE { |
||||
|
dedicatedInfoNAS OCTET STRING |
Set according to Table 7.5.1.3.3-10 |
UPLINK GENERIC NAS TRANSPORT |
||
|
} |
||||
|
nonCriticalExtension SEQUENCE {} |
Not present |
|||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
Table 7.5.1.3.3-10: UPLINK GENERIC NAS TRANSPORT (steps 1b and 7, Table 7.5.1.3.2-1)
|
Derivation Path: 24.301 Table 8.2.32.1 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
Protocol discriminator |
0111 |
EPS mobility management messages |
||
|
Security header type |
0000 |
Plain NAS message |
||
|
Uplink generic NAS transport message identity |
01101001 |
Uplink generic NAS transport |
||
|
Generic message container type |
00000001 |
LTE Positioning Protocol (LPP) message container |
||
|
Generic message container |
Step 1b: Set according to Table 7.5.1.3.3-10a |
LPP Provide Capabilities |
||
|
Step 7: Set according to Table 7.5.1.3.3-11 |
LPP Provide Location Information |
|||
|
Additional information |
present |
The UE includes the Routing Identifier received in the Additional Information IE of the DOWNLINK GENERIC NAS TRANSPORT message (step 1a or 6 Table 7.5.1.3.2-1) |
||
Table 7.5.1.3.3-10a: LPP Provide Capabilities. (step 1b, Table 7.5.1.3.2-1)
|
Derivation Path: 36.355 clause 6.2 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
LPP-Message ::= SEQUENCE { |
||||
|
transactionID SEQUENCE { |
||||
|
initiator |
locationServer |
|||
|
transactionNumber |
(0..255) |
Contains the same value as the corresponding field in the LPP Request Capabilities message in step 1a, Table 7.5.1.3.2-1 |
||
|
} |
||||
|
endTransaction |
TRUE |
|||
|
sequenceNumber |
(0..255) |
|||
|
acknowledgement SEQUENCE { |
Present, or not present |
|||
|
ackRequested |
TRUE |
|||
|
ackIndicator |
Not present |
|||
|
} |
||||
|
lpp-MessageBody CHOICE { |
||||
|
c1 CHOICE { |
||||
|
provideCapabilities SEQUENCE { |
||||
|
criticalExtensions CHOICE { |
||||
|
c1 CHOICE { |
||||
|
provideCapabilities-r9 SEQUENCE { |
||||
|
commonIEsProvideCapabilities |
Dependent on UE capabilities |
Rel-14 onwards |
||
|
a-gnss-ProvideCapabilities |
Dependent on UE capabilities |
|||
|
otdoa-ProvideCapabilities |
Dependent on UE capabilities |
|||
|
ecid-ProvideCapabilities |
Dependent on UE capabilities |
|||
|
epdu-ProvideCapabilities |
Not present |
|||
|
sensor-ProvideCapabilities-r13 |
Dependent on UE capabilities |
Rel-13 onwards |
||
|
tbs-ProvideCapabilities-r13 |
Dependent on UE capabilities |
Rel-13 onwards |
||
|
wlan-ProvideCapabilities-r13 |
Dependent on UE capabilities |
Rel-13 onwards |
||
|
bt-ProvideCapabilities-r13 |
Dependent on UE capabilities |
Rel-13 onwards |
||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
Table 7.5.1.3.3-11: LPP Provide Location Information (step 7, Table 7.5.1.3.2-1)
|
Derivation Path: 36.355 clause 6.2 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
LPP-Message ::= SEQUENCE { |
||||
|
transactionID SEQUENCE { |
||||
|
initiator |
locationServer |
|||
|
transactionNumber |
(0..255) |
Contains the same value as the corresponding field in LPP Request Location Information message in step 6, Table 7.5.1.3.2-1 |
||
|
} |
||||
|
endTransaction |
TRUE |
|||
|
sequenceNumber |
(0..255) |
|||
|
acknowledgement SEQUENCE { |
present, or not present |
|||
|
ackRequested |
TRUE |
|||
|
ackIndicator |
Not present |
|||
|
} |
||||
|
lpp-MessageBody CHOICE { |
||||
|
c1 CHOICE { |
||||
|
provideLocationInformation SEQUENCE { |
||||
|
criticalExtensions CHOICE { |
||||
|
c1 CHOICE { |
||||
|
provideLocationInformation-r9 SEQUENCE { |
||||
|
commonIEsProvideLocationInformation |
May be present. Any value acceptable |
|||
|
a-gnss-ProvideLocationInformation |
Not present |
|||
|
otdoa-ProvideLocationInformation |
May be present. Any value acceptable |
|||
|
ecid-ProvideLocationInformation |
Not present |
|||
|
epdu-ProvideLocationInformation |
Not present |
|||
|
sensor-ProvideLocationInformation-r13 |
Not present |
Rel-13 onwards |
||
|
tbs-ProvideLocationInformation-r13 |
Not present |
Rel-13 onwards |
||
|
wlan-ProvideLocationInformation-r13 |
Not present |
Rel-13 onwards |
||
|
bt-ProvideLocationInformation-r13 |
Not present |
Rel-13 onwards |
||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
|
} |
||||
Table 7.5.1.3.3-12: LPP Acknowledgement (steps 1c and 7a, Table 7.5.1.3.2-1)
|
Derivation Path: 36.355 clause 6.2 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
LPP-Message ::= SEQUENCE { |
||||
|
transactionID |
Not present |
|||
|
endTransaction |
TRUE |
|||
|
sequenceNumber |
Not present |
|||
|
acknowledgement SEQUENCE { |
||||
|
ackRequested |
FALSE |
|||
|
ackIndicator |
(0..255) |
Contains the same value of the sequenceNumber field in step 1b or 7, Table 7.5.1.3.2-1 |
||
|
} |
||||
|
lpp-MessageBody |
Not present. |
|||
|
} |
||||
Table 7.5.1.3.3-13: RRC InterFreqRSTDMeasurementIndication (step 1, Table 7.5.1.3.2-3)
|
Derivation Path: 36.331, clause 6.2.2 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
InterFreqRSTDMeasurementIndication-r10 ::= SEQUENCE{ |
||||
|
criticalExtensions CHOICE { |
||||
|
c1 CHOICE { |
||||
|
interFreqRSTDMeasurementIndication-r10 SEQUENCE { |
||||
|
rstd-InterFreqIndication-r10 CHOICE { |
||||
|
stop |
NULL |
|||
|
} |
||||
|
lateNonCriticalExtension OCTET STRING |
Not present |
|||
|
nonCriticalExtension SEQUENCE {} |
Not present |
|||
|
} |
||||
|
criticalExtensionsFuture SEQUENCE {} |
Not present |
|||
|
} |
||||
|
} |
||||
|
} |
||||
Table 7.5.1.3.3-14: RRCConnectionReconfiguration (step 2, Table 7.5.1.3.2-3)
|
Derivation Path: 36.508, Table 4.6.1-8 |
||||
|
Information Element |
Value/remark |
Comment |
Condition |
|
|
As defined in 36.508, Table 4.6.1-8 with the following exceptions: |
||||
|
measConfig ::= SEQUENCE { |
||||
|
measGapConfig CHOICE { |
||||
|
release |
NULL |
|||
|
} |
||||
|
} |
||||