6.2.1 Assisted GNSS Network Induced Tests

37.571-23GPPPart 2: Protocol conformanceRelease 16TSUser Equipment (UE) conformance specification for UE positioning

6.2.1.1 NI-LR Emergency Call: UE-Based A-GNSS

6.2.1.1.1 Definition

This test case applies to all UEs supporting UE-Based GANSS or GNSS Location Service capabilities.

6.2.1.1.2 Conformance requirements

1) A MM connection for an emergency call may be established in all states of the mobility management sublayer which allow MM connection establishment for a normal originating call.

When a user requests an emergency call establishment the UE will send a CM SERVICE REQUEST message to the network with a CM service type information element indicating emergency call establishment.

2) Having entered the "MM connection pending" state, upon MM connection establishment, the call control entity of the UE sends a setup message to its peer entity. This setup message is

– a SETUP message, if the call to be established is a basic call; and

– an EMERGENCY SETUP message, if the call to be established is an emergency call.

3) If the IE "UE positioning GANSS reference time" is included, the UE shall:

1> if the IE "GANSS Day" is included:

2> store this IE in "UE positioning GANSS reference time" in variable UE_POSITIONING_GANSS_DATA and use it as the current GANSS day.

1> store the IE "GANSS TOD" in the IE "UE positioning GANSS reference time" in variable UE_POSITIONING_GANSS_DATA and use it as an estimate of the GANSS Time-of-Day at the time of reception of the complete message containing the IE "GANSS TOD";

NOTE: The UE does not need to apply any compensation on the GANSS Time-of-Day.

1> if the IE "GANSS Time ID" is not included:

2> use Galileo system time as a reference for GANSS-Time-of-Day.

1> if the IE "GANSS Time ID" is included:

2> use the system time indicated by this IE as a reference for GANSS-Time-of-Day.

4) If the IE "UE positioning GANSS reference UE position" is included, the UE shall:

1> store this IE in the IE "UE positioning GANSS reference UE position" in variable UE_POSITIONING_GANSS_DATA; and

1> use it as a priori knowledge of the approximate location of the UE.

5) If the IE "UE positioning GANSS time model" is included, the UE shall for each GANSS:

1> store the information in "UE positioning GANSS time model" in variable UE_POSITIONING_GANSS_DATA;

1> use the stored parameters to relate GANSS time for the GANSS indicated by "GANSS ID" to time reference indicated by IE "GNSS_TO_ID".

6) The UE shall when a measurement report is triggered:

1> if the UE has been able to calculate a position after performing measurements on the cells included in the variable UE_POSITIONING_OTDOA_DATA_UE_BASED in case of OTDOA or the UE has been able to calculate a position in case of GPS or GANSS positioning or the UE has been able to calculate a position using a standalone positioning method:

2> include IE "UE positioning Position Estimate Info" in the MEASUREMENT REPORT and set the contents of the IE as follows:

3> if the UE supports the capability to provide the GANSS timing of the cell frames measurement;

3> if the IE "GANSS timing of Cell wanted" is not included, or included with each bit set to value zero:

4> include the IE "GANSS TOD msec" and set it to the GANSS TOD when the position estimate was valid.

3> if the UE does not support the capability to provide the GANSS timing of the cell:

4> include the IE "GANSS TOD msec" and set it to the GANSS TOD when the position estimate was valid;

4> include the IE "GANSS Time ID" to identify the GNSS system time.

3> if IE "Vertical Accuracy" has been included in IE "UE positioning reporting quantity":

4> if the IE "Vertical Accuracy" has been assigned to a value unequal to "0":

5> if the UE has been able to calculate a 3-dimensional position:

6> include IE "Ellipsoid point with altitude and uncertainty ellipsoid" as the position estimate.

5> if the UE has not been able to calculate a 3-dimensional position:

6> act as if IE "Vertical Accuracy" has not been included in IE "UE positioning reporting quantity".

3> if IE "Vertical Accuracy" has not been included in IE "UE positioning reporting quantity":

4> if IE "Horizontal Accuracy" in IE "UE positioning reporting quantity" has been assigned to a value unequal to 0:

5> include either IE "Ellipsoid point with uncertainty circle" or IE "Ellipsoid point with uncertainty ellipse" or IE "Ellipsoid point with altitude and uncertainty ellipsoid" as the position estimate.

3> if any of the IEs "Ellipsoid point with uncertainty ellipse" or "Ellipsoid point with altitude and uncertainty ellipsoid" is reported:

4> should calculate a value of the IE "Confidence", different from "0", as the probability that the UE is located within the uncertainty region of the one of the IEs "Ellipsoid point with uncertainty ellipse" or "Ellipsoid point with altitude and uncertainty ellipsoid" that is reported.

NOTE: The value "0" of the IE "Confidence" is interpreted as "no information" by the UTRAN].

Reference(s):

– Conformance requirement 1: TS 24.008 clause 4.5.1.5.

– Conformance requirement 2: TS 24.008, clause 5.2.1.

– Conformance requirement 3: TS 25.331, clause 8.6.7.19.7.7.

– Conformance requirement 4: TS 25.331, clause 8.6.7.19.7.8.

– Conformance requirement 5: TS 25.331, clause 8.6.7.19.7.9.

– Conformance requirement 6: TS 25.331, clause 8.6.7.19.1b.

6.2.1.1.3 Test Purpose

To verify when an emergency call is initiated by a UE, and the network performs a GANSS location request using the RRC measurement control procedure, then the UE responds with a Measurement Report containing UE location estimate.

6.2.1.1.4 Method of Test

Initial Conditions

– System Simulator (SS):

– 1 cell, default parameters.

– Satellite signals: As specified in 4.2

– User Equipment (UE):

– the UE is in state "MM idle" with valid TMSI and CKSN.

Related PICS/PIXIT Statements

– Emergency speech call

– UE Based Network Assisted GANSS

– UE Based Network Assisted GPS (Sub-tests 3, 4, 8 and 10)

Test procedure

This test case includes sub-test cases dependent on the GNSS supported by the UE. Each sub-test case is identified by a Sub-Test Case Number as defined below:

Sub-Test Case Number

Supported GNSS

1

UE supporting A-GLONASS only

2

UE supporting A-Galileo only

3

UE supporting A-GPS and Modernized GPS only

4

UE supporting A-GPS(1) and A-GLONASS only

8

UE supporting A-GPS(1) and A-Galileo only

9

UE supporting A-BDS only

10

UE supporting A-GPS(1) and A-BDS only

NOTE 1: "A-GPS" includes Modernized GPS if supported by the UE.

The UE is made to initiate an emergency call.

After the call has been through-connected in both directions, the SS orders an A-GNSS positioning measurement using one or more (dependent on the Sub-Test) MEASUREMENT CONTROL messages. The last MEASUREMENT CONTROL message orders periodical reporting by sending a MEASUREMENT CONTROL message requesting periodical measurement reporting (1 report, interval 64s).

The UE then performs positioning measurements, calculates "UE Positioning Position Estimate Info" and responds with this in the RRC message MEASUREMENT REPORT.

Finally the SS clears the call.

Expected Sequence

Step

Direction

Message

Comments

UE

SS

1

UE

The "emergency number" is entered. Number shall be one programmed in test USIM EFECC (Emergency Call Codes), ref. 34.108 clause 8.3.2.21.

2

–>

UE establishes RRC procedure for emergency call.

Establishment cause: Emergency Call
SS checks that the UE capability includes "Network Assisted GANSS Support List" with "GANSS mode" set to "UE-based", and that the UE includes "Network Assisted GPS Support" for UE-based (Sub-Tests 3, 4, 8 and 10 only).

3

–>

CM SERVICE REQUEST

The CM service type IE indicates "emergency call establishment".

4

<–

AUTHENTICATION REQUEST

IE Authentication Parameter AUTN shall be present in the message.

5

–>

AUTHENTICATION RESPONSE

SRES specifies correct value.

6

SS starts security procedure.

7

–>

EMERGENCY SETUP

If the Bearer capability IE is not included the default UMTS AMR speech version shall be assumed.

8

<–

CALL PROCEEDING

9

<–

ALERTING

10

<–

SS sets up the radio bearer with the rate indicated by the EMERGENCY SETUP message.

11

<–

CONNECT

12

–>

CONNECT ACKNOWLEDGE

13

UE

The DTCH is through connected in both directions.

14

<–

MEASUREMENT CONTROL

All Sub-Tests

14a

<–

MEASUREMENT CONTROL

Sub-Tests 2, 3, 4, 8, 10 only

14b

<–

MEASUREMENT CONTROL

Sub-Tests 4, 8, 10 only

15

–>

MEASUREMENT REPORT

16

<–

DISCONNECT

SS disconnects the call and associated radio bearer.

Specific Message Contents

MEASUREMENT CONTROL (Step 14):

Information element

Value/remark

Measurement Information Elements

Measurement Identity

10

Measurement Command

Setup

Measurement Reporting Mode

– Measurement report transfer mode

Acknowledged mode RLC

– Periodical reporting / Event trigger reporting mode

Periodical reporting

Additional Measurements List

Not present

CHOICE Measurement type

UE positioning measurement

– UE positioning measurement

– UE positioning reporting quantity

– Method type

UE based

– Positioning methods

GPS

– Response time

128

– Horizontal accuracy

127

– Vertical accuracy

127

– GPS timing of cell wanted

FALSE

– Multiple sets

FALSE

– Additional assistance data request

FALSE

– Environmental characterization

Not present

– Velocity Requested

Not present

– GANSS Positioning Method

Sub-Test 1: bit 5 = 1

Sub-Test 2: bit 1 = 1

Sub-Test 3: bit 0 and 3 = 1

Sub-Test 4: bit 0 and 3 and 5 = 1

Sub-Test 8: bit 0 and 1 and 3 = 1

Sub-Test 9: bit 6 = 1

Sub-Test 10: bit 0 and 3 and 6 = 1

– GANSS timing of cell wanted

Not present

– GANSS Carrier-Phase Measurement Requested

Not present

– GANSS Multi-frequency Measurement Requested

Not present

– Measurement validity

– UE state

All states

– CHOICE Reporting criteria

– Periodical reporting criteria

For Sub-Tests 1, 9 only

– Amount of reporting

1

– Reporting interval

64000

– No reporting

For Sub-Tests 2, 3, 4, 8, 10 only

– UE pos OTDOA assistance data for UE-assisted

Not present

– UE pos OTDOA assistance data for UE-based

Not present

– UE positioning GPS assistance data

Set as specified for the first MEASUREMENT CONTROL message for "Adequate assistance data for UE-based A-GNSS" in 4.4.1

– UE positioning GANSS assistance data

Set as specified for the first MEASUREMENT CONTROL message for "Adequate assistance data for UE-based A-GNSS" in 4.4.1

Physical Channel Information Elements

DPCH compressed mode status info

Not present

MEASUREMENT CONTROL (Step 14a):

Information element

Value/remark

Measurement Information Elements

Measurement Identity

10

Measurement Command

Modify

Measurement Reporting Mode

– Measurement report transfer mode

Acknowledged mode RLC

– Periodical reporting / Event trigger reporting mode

Periodical reporting

Additional Measurements List

Not present

CHOICE Measurement type

UE positioning measurement

– UE positioning measurement

– UE positioning reporting quantity

– Method type

UE based

– Positioning methods

GPS

– Response time

128

– Horizontal accuracy

127

– Vertical accuracy

127

– GPS timing of cell wanted

FALSE

– Multiple sets

FALSE

– Additional assistance data request

FALSE

– Environmental characterization

Not present

– Velocity Requested

Not present

– GANSS Positioning Method

Sub-Test 2: bit 1 = 1

Sub-Test 3: bit 0 and 3 = 1

Sub-Test 4: bit 0 and 3 and 5 = 1

Sub-Test 8: bit 0 and 1 and 3 = 1

Sub-Test 9: bit 6 = 1

Sub-Test 10: bit 0 and 3 and 6 = 1

– GANSS timing of cell wanted

Not present

– GANSS Carrier-Phase Measurement Requested

Not present

– GANSS Multi-frequency Measurement Requested

Not present

– Measurement validity

– UE state

All states

– CHOICE Reporting criteria

– Periodical reporting criteria

For Sub-Tests 2, 3 only

– Amount of reporting

1

– Reporting interval

64000

– No reporting

For Sub-Tests 4, 8, 10 only

– UE pos OTDOA assistance data for UE-assisted

Not present

– UE pos OTDOA assistance data for UE-based

Not present

– UE positioning GPS assistance data

Set as specified for the second MEASUREMENT CONTROL message for "Adequate assistance data for UE-based A-GNSS" in 4.4.1

– UE positioning GANSS assistance data

Set as specified for the second MEASUREMENT CONTROL message for "Adequate assistance data for UE-based A-GNSS" in 4.4.1

Physical Channel Information Elements

DPCH compressed mode status info

Not present

MEASUREMENT CONTROL (Step 14b):

Information element

Value/remark

Measurement Information Elements

Measurement Identity

10

Measurement Command

Modify

Measurement Reporting Mode

– Measurement report transfer mode

Acknowledged mode RLC

– Periodical reporting / Event trigger reporting mode

Periodical reporting

Additional Measurements List

Not present

CHOICE Measurement type

UE positioning measurement

– UE positioning measurement

– UE positioning reporting quantity

– Method type

UE based

– Positioning methods

GPS

– Response time

128

– Horizontal accuracy

127

– Vertical accuracy

127

– GPS timing of cell wanted

FALSE

– Multiple sets

FALSE

– Additional assistance data request

FALSE

– Environmental characterization

Not present

– Velocity Requested

Not present

– GANSS Positioning Method

Sub-Test 4: bit 0 and 3 and 5 = 1

Sub-Test 8: bit 0 and 1 and 3 = 1

Sub-Test 10: bit 0 and 3 and 6 = 1

– GANSS timing of cell wanted

Not present

– GANSS Carrier-Phase Measurement Requested

Not present

– GANSS Multi-frequency Measurement Requested

Not present

– Measurement validity

– UE state

All states

– CHOICE Reporting criteria

– Periodical reporting criteria

– Amount of reporting

1

– Reporting interval

64000

– UE pos OTDOA assistance data for UE-assisted

Not present

– UE pos OTDOA assistance data for UE-based

Not present

– UE positioning GPS assistance data

Set as specified for the third MEASUREMENT CONTROL message for "Adequate assistance data for UE-based A-GNSS" in 4.4.1

– UE positioning GANSS assistance data

Set as specified for the third MEASUREMENT CONTROL message for "Adequate assistance data for UE-based A-GNSS" in 4.4.1

Physical Channel Information Elements

DPCH compressed mode status info

Not present

MEASUREMENT REPORT (Step 15):

Information element

Value/remark

Measurement Information Elements

Measurement Identity

10

Measured Results

– CHOICE Measurement

UE positioning measured results

– UE positioning measured results

– UE positioning OTDOA measured results

Not present

– UE positioning position estimate info

– CHOICE Reference time

GPS or GANSS reference time only

– GPS TOW msec

Not checked

– GANSS TOD msec

Not checked

– CHOICE Position estimate

One of ‘Ellipsoid point with uncertainty Circle’ or ‘Ellipsoid point with uncertainty Ellipse’ or ‘Ellipsoid point with altitude and uncertainty Ellipsoid’

– Position Data

Not checked

– CHOICE Velocity estimate

Not present

– UE positioning GPS measured results

Not present

– UE positioning error

Not present

– UE positioning GANSS measured results

Not present

Measured Results on secondary UL frequency

Not present

Measured Results on RACH

Not present

Additional Measured Results

Not present

Additional Measured results on secondary UL frequency

Not present

Event Results

Not present

Event results on secondary UL frequency

Not present

Inter-RAT cell info indication

Not present

E-UTRA Measured Results

Not present

E-UTRA Event Results

Not present

CSG Proximity Indication

Not present

6.2.1.1.5 Test requirements

After step 12 the UE shall have through connected the DTCH in both directions.

After step 14, 14a, or 14b (dependent on Sub-Test) the UE shall respond with a MEASUREMENT REPORT message.

6.2.1.2 NI-LR Emergency call: UE-Assisted A-GNSS

6.2.1.2.1 Definition

This test case applies to all UEs supporting UE-Assisted GANSS or GNSS Location Service capabilities.

6.2.1.2.2 Conformance requirements

1) A MM connection for an emergency call may be established in all states of the mobility management sublayer which allow MM connection establishment for a normal originating call.

When a user requests an emergency call establishment the UE will send a CM SERVICE REQUEST message to the network with a CM service type information element indicating emergency call establishment.

2) Having entered the "MM connection pending" state, upon MM connection establishment, the call control entity of the UE sends a setup message to its peer entity. This setup message is

– a SETUP message, if the call to be established is a basic call; and

– an EMERGENCY SETUP message, if the call to be established is an emergency call.

3) The a measurement report is triggered:

1> if the UE was UE shall when able to perform measurements on at least one neighbour cell included in the variable UE_POSITIONING_OTDOA_DATA_UE_ASSISTED in case of OTDOA or one satellite included in the variable UE_POSITIONING_GPS_DATA in case of GPS positioning or one satellite included in the variable UE_POSITIONING_GANSS_DATA in case of GANSS positioning or one cell from the active set in case of CELL ID:

2> if the IE "Vertical Accuracy" is included:

3> interpret the presence of this IE to indicate that the UTRAN desires to compute a 3-dimensional position estimate.

2> if the IE "Positioning Methods" is set to "GPS" and if the IE "GANSS Positioning Methods" is not present or if the IE "GANSS Positioning Methods" is present indicating GPS allowed:

3> include the IE "UE positioning GPS measured results" in the measurement report and set the contents of the IE as follows:

4> if the UE supports the capability to provide the GPS timing of the cell frames measurement:

5> if the IE "GPS timing of Cell wanted" is set to FALSE:

7> include the IE "GPS TOW msec" and set it to the GPS TOW when the measurements included in the MEASUREMENT REPORT were valid;

7> include the IE "UE Positioning GPS Reference Time Uncertainty" and set it to the uncertainty of the GPS TOW when the measurements included in the MEASUREMENT REPORT were valid.

4> if the UE does not support the capability to provide the GPS timing of the cell:

5> include the IE "GPS TOW msec" and set it to the GPS TOW when the measurements included in the MEASUREMENT REPORT were valid;

5> include the IE "UE Positioning GPS Reference Time Uncertainty" and set it to the uncertainty of the GPS TOW when the measurements included in the MEASUREMENT REPORT were valid.

2> if the IE "Positioning Methods" is set to "GPS" and the IE "GANSS Positioning Methods" is present indicating other GNSS than GPS allowed and if any of these other GNSSs is measured:

3> include the IE "UE positioning GANSS measured results" in the measurement report and set the contents of the IE as follows:

4> if the UE supports the capability to provide the GANSS timing of the cell frames measurement:

5> if the IE "GANSS timing of Cell wanted" is not included, or included with each bit set to value zero and if IE "UE positioning GPS measured results" is not present:

6> include the IE "GANSS TOD msec" and set it to the GANSS TOD when the measurements included in the MEASUREMENT REPORT were valid.

4> if the UE does not support the capability to provide the GANSS timing of the cell and if IE "UE positioning GPS measured results" is not present:

5> include the IE "GANSS TOD msec" and set it to the GANSS TOD when the measurements included in the MEASUREMENT REPORT were valid.

4> if the UE supports the capability to perform GANSS measurements on multiple GANSS frequencies:

5> if the IE "GANSS Multi-frequency Measurement Requested" is included with one bit set to value one for a supported GANSS, and if any of these GANSS signals are measured:

6> include the IE "GANSS Signal Measurement Information" for each measured GANSS signal.

References

– Conformance requirement 1: TS 24.008 clause 4.5.1.5.

– Conformance requirement 2: TS 24.008, clause 5.2.1.

– Conformance requirement 3: TS 25.331, clause 8.6.7.19.1a.

6.2.1.2.3 Test Purpose

To verify when an emergency call is initiated by a UE, and the network performs a GANSS location request using the RRC measurement control procedure, then the UE responds with a Measurement Report containing "UE positioning GANSS measured results" and "UE positioning GPS measured results" (Sub-tests 3, 4, 8 and 10).

6.2.1.2.4 Method of Test

Initial Conditions

– System Simulator (SS):

– 1 cell, default parameters.

– Satellite signals: As specified in 4.2.

– User Equipment (UE):

– the UE is in state "MM idle" with valid TMSI and CKSN.

Related PICS/PIXIT Statements

– Emergency speech call

– UE Assisted Network Assisted GANSS

– UE Assisted Network Assisted GPS (Sub-tests 3, 4, 8 and 10)

Test Procedure

This test case includes sub-test cases dependent on the GNSS supported by the UE. Each sub-test case is identified by a Sub-Test Case Number as defined below:

Sub-Test Case Number

Supported GNSS

1

UE supporting A-GLONASS only

2

UE supporting A-Galileo only

3

UE supporting A-GPS and Modernized GPS only

4

UE supporting A-GPS(1) and A-GLONASS only

8

UE supporting A-GPS(1) and A-Galileo only

9

UE supporting A-BDS only

10

UE supporting A-GPS(1) and A-BDS only

NOTE 1: "A-GPS" includes Modernized GPS if supported by the UE.

The UE is made to initiate an emergency call.

After the call has been through-connected in both directions, the SS orders an A-GNSS positioning measurement using a MEASUREMENT CONTROL message, including assistance data as specified in subclause 4.4.3. The UE may request additional assistance data by sending a MEASUREMENT REPORT message containing a positioning error indication with the IE "Error reason" set to "Assistance Data Missing". If the UE requests additional assistance data, the SS provides the requested assistance data in one or more MEASUREMENT CONTROL messages.

The UE then performs positioning measurements and responds with the RRC message MEASUREMENT REPORT.

Finally the SS clears the call.

Expected Sequence

Step

Direction

Message

Comments

UE

SS

1

UE

The "emergency number" is entered. Number shall be one programmed in test USIM EFECC (Emergency Call Codes), ref. 34.108 clause 8.3.2.21.

2

–>

UE establishes RRC procedure for emergency call.

Establishment cause: Emergency Call
SS checks that the UE capability includes "Network Assisted GANSS Support List" with "GANSS mode" set to "UE-assisted", and that the UE includes "Network Assisted GPS Support" for UE-assisted (Sub-Tests 3, 4, 8 and 10 only).

3

–>

CM SERVICE REQUEST

The CM service type IE indicates "emergency call establishment".

4

<–

AUTHENTICATION REQUEST

IE Authentication Parameter AUTN shall be present in the message.

5

–>

AUTHENTICATION RESPONSE

SRES specifies correct value.

6

SS

SS starts security procedure.

7

–>

EMERGENCY SETUP

If the Bearer capability IE is not included the default UMTS AMR speech version shall be assumed.

8

<–

CALL PROCEEDING

9

<–

ALERTING

10

<–

SS sets up the radio bearer with the rate indicated by the EMERGENCY SETUP message.

11

<–

CONNECT

12

–>

CONNECT ACKNOWLEDGE

13

UE

The DTCH is through connected in both directions.

14

<–

MEASUREMENT CONTROL

15

–>

MEASUREMENT REPORT

UE reports positioning measurement results (Option 1) or requests additional assistance data (Option 2).

15a

<–

MEASUREMENT CONTROL

If UE requested additional assistance data in step 15, SS provides the requested data in one or more MEASUREMENT CONTROL messages as specified in subclause 4.4.5.

15b

–>

MEASUREMENT REPORT

If UE requested additional assistance data in step 15, this message contains the IE "UE positioning GANSS measured results" and "UE positioning GPS measured results" (Sub-tests 3, 4, 8 and 10).

16

<–

DISCONNECT

SS disconnects the call and associated radio bearer.

Specific Message Contents

MEASUREMENT CONTROL (Step 14):

Information element

Value/remark

Measurement Information Elements

Measurement Identity

10

Measurement Command

Setup

Measurement Reporting Mode

– Measurement report transfer mode

Acknowledged mode RLC

– Periodical reporting / Event trigger reporting mode

Periodical reporting

Additional Measurements List

Not present

CHOICE Measurement type

UE positioning measurement

– UE positioning measurement

– UE positioning reporting quantity

– Method type

UE assisted

– Positioning methods

GPS

– Response time

128

– Horizontal accuracy

127

– Vertical accuracy

127

– GPS timing of cell wanted

FALSE

– Multiple sets

FALSE

– Additional assistance data request

TRUE

– Environmental characterization

Not present

– Velocity Requested

Not present

– GANSS Positioning Method

Sub-Test 1: bit 5 = 1

Sub-Test 2: bit 1 = 1

Sub-Test 3: bit 0 and 3 = 1

Sub-Test 4: bit 0 and 3 and 5 = 1

Sub-Test 8: bit 0 and 1 and 3 = 1

Sub-Test 9: bit 6 = 1

Sub-Test 10: bit 0 and 3 and 6 = 1

– GANSS timing of cell wanted

Not present

– GANSS Carrier-Phase Measurement Requested

Not present

– GANSS Multi-frequency Measurement Requested

Set according to UE capabilities

– Measurement validity

– UE state

All states

– CHOICE Reporting criteria

– Periodical reporting criteria

– Amount of reporting

1

– Reporting interval

64000

– UE pos OTDOA assistance data for UE-assisted

Not present

– UE pos OTDOA assistance data for UE-based

Not present

– UE positioning GPS assistance data

Set as specified for "Adequate assistance data for UE-assisted A-GNSS" in 4.4.3

– UE positioning GANSS assistance data

Set as specified for "Adequate assistance data for UE-assisted A-GNSS" in 4.4.3

Physical Channel Information Elements

DPCH compressed mode status info

Not present

MEASUREMENT REPORT (Step 15 (Option 1) or 15b (Option 2))

Information element

Value/remark

Measurement Information Elements

Measurement Identity

10

Measured Results

– CHOICE Measurement

UE positioning measured results

– UE positioning measured results

– UE positioning OTDOA measured results

Not present

– UE positioning position estimate info

Not present

– UE positioning GPS measured results

Present for Sub-Tests 3, 4, 8 and 10

– UE positioning error

Not present

– UE positioning GANSS measured results

Present

Measured Results on secondary UL frequency

Not present

Measured Results on RACH

Not present

Additional Measured Results

Not present

Additional Measured results on secondary UL frequency

Not present

Event Results

Not present

Event results on secondary UL frequency

Not present

Inter-RAT cell info indication

Not present

E-UTRA Measured Results

Not present

E-UTRA Event Results

Not present

CSG Proximity Indication

Not present

MEASUREMENT REPORT (Step 15 (Option 2)):

Information element

Value/remark

Measurement Information Elements

Measurement Identity

10

Measured Results

– CHOICE Measurement

UE positioning measured results

– UE positioning measured results

– UE positioning OTDOA measured results

Not present

– UE positioning position estimate info

Not present

– UE positioning GPS measured results

Not present

– UE positioning error

Not present

– Error reason

Assistance Data Missing

– GPS Additional Assistance Data Request

Not checked

– GANSS Additional Assistance Data Request

Not checked

– UE positioning GANSS measured results

Not present

Measured Results on secondary UL frequency

Not present

Measured Results on RACH

Not present

Additional Measured Results

Not present

Additional Measured results on secondary UL frequency

Not present

Event Results

Not present

Event results on secondary UL frequency

Not present

Inter-RAT cell info indication

Not present

E-UTRA Measured Results

Not present

E-UTRA Event Results

Not present

CSG Proximity Indication

Not present

MEASUREMENT CONTROL (Step 15a (Option 2)):

Information element

Value/remark

Measurement Information Elements

Measurement Identity

10

Measurement Command

Modify

Measurement Reporting Mode

– Measurement report transfer mode

Acknowledged mode RLC

– Periodical reporting / Event trigger reporting mode

Periodical reporting

Additional Measurements List

Not present

CHOICE Measurement type

UE positioning measurement

– UE positioning measurement

– UE positioning reporting quantity

– Method type

UE assisted

– Positioning methods

GPS

– Response time

128

– Horizontal accuracy

127

– Vertical accuracy

127

– GPS timing of cell wanted

FALSE

– Multiple sets

FALSE

– Additional assistance data request

FALSE

– Environmental characterization

Not present

– Velocity Requested

Not present

– GANSS Positioning Method

Sub-Test 1: bit 5 = 1

Sub-Test 2: bit 1 = 1

Sub-Test 3: bit 0 and 3 = 1

Sub-Test 4: bit 0 and 3 and 5 = 1

Sub-Test 8: bit 0 and 1 and 3 = 1

Sub-Test 9: bit 6 = 1

Sub-Test 10: bit 0 and 3 and 6 = 1

– GANSS timing of cell wanted

Not present

– GANSS Carrier-Phase Measurement Requested

Not present

– GANSS Multi-frequency Measurement Requested

Set according to UE capabilities

– Measurement validity

– UE state

All states

– CHOICE Reporting criteria

– Periodical reporting criteria

– Amount of reporting

1

– Reporting interval

64000

– UE pos OTDOA assistance data for UE-assisted

Not present

– UE pos OTDOA assistance data for UE-based

Not present

– UE positioning GPS assistance data

Set as specified in 4.4.5

– UE positioning GANSS assistance data

Set as specified in 4.4.5

Physical Channel Information Elements

DPCH compressed mode status info

Not present

6.2.1.2.5 Test requirements

After step 12 the UE shall have through connected the DTCH in both directions.

After step 14 the UE shall send a MEASUREMENT REPORT message containing the IE "UE positioning GPS measured results" and/or "UE positioning GANSS measured results".