5 Applicability of Requirements

37.145-13GPPActive Antenna System (AAS) Base Station (BS) conformance testingPart 1: conducted conformance testingRelease 17TS

5.1 General

The present clause defines for each conducted test requirement the set of mandatory test configurations which shall be used for demonstrating conformance for each TAB connector.

Test configurations for TAB connectors supporting multiple RAT in the tested operating band are specified in clause 5.2.

Test configurations for TAB connectors declared to support single RAT requirements (see table 4.10-1, D6.13) by either MSR requirements for UTRA only or E-UTRA only or with a single-RAT UTRA requirements or single RAT E-UTRA requirements are specified in clause 5.3.

Test configurations for Multi-band TAB connectors are specified in clause 5.4.

Requirements apply to TAB connectors according to the declared RAT Capability Set (see table 4.10-1, D6.12) within each supported operating band and capability set of the TAB connector and the Band Category of the declared operating band (see table 4.10-1, D6.1), as listed in the heading of each table. Some RF requirements listed in the tables may not be mandatory or they may apply only regionally. This is further specified for each requirement in clauses 6 and 7, and in table 4.4-1.

For a declared RAT Capability Set (see table 4.10-1, D6.12) in tables 5.2-1, 5.3.2-1, 5.3.3-1, 5.3.4-1, 5.4.1-1 or 5.4.2.1 only the requirements listed in the column for that Capability Set apply. Requirements listed under CSA other than the declared CSA(s) need not be tested. In case the BS is declared to support more than one CS, the tests that are common between different supported CSs are not repeated.

For a TAB connector declared to support MSR and to be capable of contiguous spectrum operation only, the test configuration(s) in tables 5.2-1 and 5.3.2-1 denoted by a "C" and entries that refer to single-RAT specifications shall be used for testing.

For a TAB connector that is declared: to support MSR and to be capable of contiguous and non-contiguous spectrum operation (see table 4.10-1, D6.14), where the parameters according to clause 4.10 are identical for contiguous and non-contiguous operation (see table 4.10-1, D6.15), shall use for each declared operating band the test configuration(s) in tables 5.2-1 and 5.3.2-1 denoted by "CNC" and entries that refer to single-RAT specifications shall be used.

For a TAB connector that is declared: to support MSR and to be capable of contiguous and non-contiguous spectrum operation (see table 4.10-1, D6.14), where the parameters according to clause 4.10 are not identical for contiguous and non-contiguous operation (see table 4.10-1, D6.15), shall use for each declared operating band the test configuration(s) in tables 5.2-1 and 5.3.2-1 denoted by "C/NC" and entries that refer to single-RAT specifications shall be used.

For a MSR capable multi-band TAB connector the applicability of the requirement for each operating band is determined by the RAT configuration within that operating band as identified in tables 5.2-1 and 5.3.2-1, unless otherwise stated. The testing of MSR capable multi-band TAB connectors shall be according to table 5.4.1-1 as follows:

– For requirements test denoted by SBT (Single Band Test), the test configuration(s) in tables 5.2-1 and 5.3.2-1 shall be used for each operating band depending on the RAT configuration within that band.

– For requirements test denoted by MBT (Multi-Band Test), the test configuration(s) in table 5.4.1-1 shall be used depending on the Band Category of the declared operating band combination.

For a single-RAT UTRA only TAB connector for each declared operating band clause 5.3.3 defines for each conducted test requirement the set of mandatory test configurations which shall be used for demonstrating conformance. The applicable test configurations are specified in table 5.3.3-1 for each supported RF configuration, which shall be declared according to clause 4.10. The generation and power allocation for each test configuration is defined in clause 4.11.2.

For a single-RAT E-UTRA only TAB connector for each declared operating band clause 5.3.4 defines for each conducted test requirement the set of mandatory test configurations which shall be used for demonstrating conformance. The applicable test configurations are specified in table 5.3.4-1 for each supported RF configuration, which shall be declared according to clause 4.10. The generation and power allocation for each test configuration is defined in clause 4.11.2.

For a TAB connector declared to be capable of single carrier operation only in an operating band (see table 4.10-1, D6.23), a single carrier (SC) shall be used for testing.

5.2 Test configurations for TAB connectors for operating bands where MSR is supported

Table 5.2-1: Test configuration applicability to requirements and
capability sets for TAB connectors supporting MSR operation

TAB connector test case

UTRA + E-UTRA (CSA3)

E-UTRA + NR (CSA3A)

UTRA + E-UTRA + NR (CSA3B)

BC1

BC2

BC3

BC1

BC2

BC3

BC1, BC2

6.2

Base Station output power

–

–

–

–

–

–

–

6.2.2

Base Station maximum output power

C: ATC3a CNC: ATC3a C/NC: ATC3a, ANTC3 

C: ATC3a CNC: ATC3a C/NC: ATC3a, ANTC3

C: ATC3b

C: ATC6

CNC: ATC6 C/NC: ATC6, ANTC6 

C: ATC6 CNC: ATC6 C/NC: ATC6, ANTC6

C: ATC6

CNC: ATC6 C/NC: ATC6, ANTC6

C: ATC8

CNC: ANTC8

C/NC: ANTC8, ATC8

 

Additional regional requirement (only for band 34)

N/A

N/A

(Note 1)

N/A

N/A

(Note 1)

N/A

6.2.3

UTRA FDD primary CPICH power

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

Clause 5.3.3

6.2.3A

UTRA FDD secondary CPICH power

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

Clause 5.3.3

6.2.4

UTRA TDD primary CCPCH power

N/A

N/A

Clause 5.3.3

N/A

N/A

N/A

N/A

6.2.6

E-UTRA DL RS power

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

6.3

Output power dynamics

–

–

–

–

–

–

–

 

E-UTRA

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

 

UTRA FDD

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

Clause 5.3.3

 

UTRA TDD

N/A

N/A

Clause 5.3.3

N/A

N/A

N/A

N/A

NR

N/A

N/A

N/A

SC

SC

SC

SC

6.4

Transmit ON/OFF power

–

–

–

–

–

–

–

6.4.1

Transmitter OFF power

N/A

N/A

C: ATC3b

N/A

N/A

C: ATC6

CNC: ATC6 C/NC: ATC6, ANTC6

N/A

6.4.2

Transmitter transient period

N/A

N/A

C: ATC3b

N/A

N/A

C: ATC6

CNC: ATC6 C/NC: ATC6, ANTC6

N/A

6.5

Transmitted signal quality

–

–

–

–

–

–

–

6.5.2

Frequency error

–

–

–

–

–

–

–

 

E-UTRA

Same TC as used in clause 6.5.4

Same TC as used in clause 6.5.4

Same TC as used in clause 6.5.4

Same TC as used in clause 6.5.4

Same TC as used in clause 6.5.4

Same TC as used in clause 6.5.4

Same TC as used in subclause 6.5.4

 

UTRA FDD

Same TC as used in clause 6.5.4

Same TC as used in clause 6.5.4

N/A

N/A

N/A

N/A

Same TC as used in subclause 6.5.4

 

UTRA TDD

N/A

N/A

Same TC as used in clause 6.5.4

N/A

N/A

N/A

N/A

NR

N/A

N/A

N/A

Same TC as used in clause 6.5.4

Same TC as used in clause 6.5.4

Same TC as used in clause 6.5.4

Same TC as used in subclause 6.5.4

6.5.3

Time alignment error

–

–

–

–

–

–

–

 

E-UTRA

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

 

UTRA FDD

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

Clause 5.3.3

 

UTRA TDD

N/A

N/A

Clause 5.3.3

N/A

N/A

N/A

N/A

NR

N/A

N/A

N/A

ATC7

ATC7

ATC7, ANTC7

ATC7

6.5.4

Modulation quality – EVM

–

–

–

–

–

–

–

 

E-UTRA

C: ATC3a CNC: ATC3a C/NC: ATC3a, ANTC3

C: ATC3a CNC: ATC3a C/NC: ATC3a, ANTC3

C: ATC3b

C: ATC6

CNC: ATC6 C/NC: ATC6, ANTC6

C: ATC6 CNC: ATC6 C/NC: ATC6, ANTC6

C: ATC6

CNC: ATC6 C/NC: ATC6, ANTC6

C: ATC8

CNC: ATC8

C/NC: ANTC8, ATC8

 

UTRA FDD

C: ATC3a CNC: ATC3a C/NC: ATC3a, ANTC3

C: ATC3a CNC: ATC3a C/NC: ATC3a, ANTC3

N/A

N/A

N/A

N/A

C:

CNC: ATC8

C/NC: ANTC8, ATC8

 

UTRA TDD

N/A

N/A

C: ATC3b

N/A

N/A

N/A

N/A

NR

N/A

N/A

N/A

C: ATC6

CNC: ATC6 C/NC: ATC6, ANTC6

C: ATC6 CNC: ATC6 C/NC: ATC6, ANTC6

C: ATC6

CNC: ATC6 C/NC: ATC6, ANTC6

C: ANTC8

CNC:

C/NC: ANTC8, ANTC8

6.5.5

Transmit pulse shape filter

Not tested

Not tested

Not tested

Not tested

Not tested

Not tested

Not tested

6.6

Unwanted Emissions

–

–

–

–

–

–

–

6.6.2

Occupied bandwidth

–

–

–

–

–

–

–

 

Minimum requirement

Clause 5.3.3 Clause 5.3.4

Clause 5.3.3 Clause 5.3.4

Clause 5.3.3 Clause 5.3.4

Clause 5.3.3 Clause 5.3.4

Clause 5.3.3 Clause 5.3.4

Clause 5.3.3 Clause 5.3.4

Clause 5.3.3 Clause 5.3.4

6.6.3

Adjacent Channel Leakage power Ratio

–

–

–

–

–

–

–

 

E-UTRA

C: ATC2a CNC: ANTC2 C/NC:ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC:ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC:ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC:ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC:ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC:ATC2a, ANTC2

C: ATC8

CNC: ANTC8

C/NC: ANTC8, ATC6a

 

UTRA FDD

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

C: ATC6a

CNC: ANTC8

C/NC: ANTC8, ATC6a

 

UTRA TDD

N/A

N/A

Clause 5.3.3

N/A

N/A

N/A

N/A

NR

N/A

N/A

N/A

C: ATC7

CNC: ANTC7

C/NC: ATC7, ANTC7

C: ATC7

CNC: ANTC7

C/NC: ATC7, ANTC7

C: ATC7

CNC: ANTC7

C/NC: ATC7, ANTC7

C: ATC6a

CNC: ANTC8

C/NC: ANTC8, ANTC8

 

Cumulative ACLR

CNC: ANTC3 C/NC:ANTC3

CNC: ANTC3 C/NC:ANTC3

CNC: ANTC6 C/NC:ANTC6

CNC: ANTC6 C/NC:ANTC6

CNC: ANTC6 C/NC:ANTC6

CNC: ANTC8

C/NC: ANTC8

6.6.5

Operating band unwanted emission

–

–

–

–

–

–

–

 

General requirement for Band Categories 1 and 3

Clause 5.3.3 Clause 5.3.4 C: ATC3a CNC: ATC3a, ANTC3 C/NC: ATC3a, ANTC3

N/A

Clause 5.3.3 Clause 5.3.4 C: ATC3b

Clause 5.3.3 Clause 5.3.4

C: ATC6

CNC: ATC6, ANTC6

C/NC: ATC6, ANTC6

N/A

Clause 5.3.3 Clause 5.3.4

C: ATC6

CNC: ATC6, ANTC6

C/NC: ATC6, ANTC6

C: ATC8

CNC,: ATC8, ANTC8

C/NC, : ANTC8, ATC8

SC: (Note 2)

 

General requirement for Band Category 2

N/A

Clause 5.3.3 Clause 5.3.4
C: ATC3a CNC: ATC3a, ANTC3 C/NC: ATC3a, ANTC3

N/A

N/A

Clause 5.3.3 Clause 5.3.4
C: ATC6 CNC: ATC6, ANTC6

C/NC: ATC6, ANTC6

N/A

C: ATC8

CNC: ANTC8

C/NC, : ANTC8, ATC8

SC: (Note 2)

 

Additional requirements 

(Note 1)

(Note 1)

(Note 1)

(Note 1)

(Note 1)

(Note 1)

(Note 1)

6.6.6

Spurious emission

–

–

–

–

–

–

–

 

(Category A)

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3b

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6 CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC8

CNC: ANTC8

C/NC: ANTC8, ATC8

 

(Category B)

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3a CNC: ANTC3C/NC: ATC3a, ANTC3

C: ATC3b

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6 CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC8

CNC: ANTC8

C/NC: ANTC8, ATC8

 

Additional requirement for BC2 (Category B)

N/A

N/A

N/A

N/A

N/A

N/A

N/A

 

Protection of the BS receiver of own or different BS

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3b

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6 CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC8

CNC: ANTC8

C/NC: ANTC8, ATC8

 

Additional spurious emissions requirements

C: ATC3a, CNC: ANTC3, C/NC: ATC3a, ATC3a

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3b

C: ATC6, CNC: ANTC6, C/NC: ATC6, ATC6

C: ATC6 CNC: ANTC6

C/NC: ATC6, ANTC6

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC8

CNC: ANTC8

C/NC: ANTC8, ATC8

 

Co-location with other Base Stations

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3b

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6 CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC8

CNC: ANTC8

C/NC: ANTC8, ATC8

6.7

Transmitter intermodulation

–

–

–

–

–

–

–

 

General requirement

Same TC as used in clause 6.6

Same TC as used in clause 6.6

Same TC as used in clause 6.6 

Same TC as used in clause 6.6

Same TC as used in clause 6.6

Same TC as used in clause 6.6 

Same TC as used in 6.6

 

Additional requirement (BC1 and BC2)

CNC: ANTC3 C/NC:ANTC3

Same TC as used in clause 6.6

N/A

CNC: ANTC6 C/NC:ANTC6

Same TC as used in clause 6.6

N/A

CNC: ANTC8

C/NC: ANTC8

 

Additional requirement (BC3)

N/A

N/A

Same TC as used in clause 6.6

N/A

N/A

N/A

N/A

7.2

Reference sensitivity level

–

–

–

–

–

–

–

 

E-UTRA requirement

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

 

UTRA FDD requirement

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

Clause 5.3.3

 

UTRA TDD requirement

N/A

N/A

Clause 5.3.3

N/A

N/A

N/A

N/A

NR

N/A

N/A

N/A

SC

SC

SC

SC

7.3

Dynamic range

–

–

–

–

–

–

–

 

E-UTRA

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

 

UTRA FDD

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

Clause 5.3.3

 

UTRA TDD

N/A

N/A

Clause 5.3.3

N/A

N/A

N/A

N/A

NR

N/A

N/A

N/A

SC

SC

SC

SC

7.4

Adjacent channel selectivity and narrowband blocking

–

–

–

–

–

–

–

 

General blocking requirement

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3b

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6 CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC8

CNC: ANTC8

C/NC: ANTC8, ATC8

 

General narrowband blocking requirement

C: ATC3a, ATC4b CNC:ANTC3, ATC4b C/NC: ATC3a, ANTC3,ATC4b

C: ATC3a, ATC4b CNC:ANTC3, ATC4b C/NC: ATC3a, ANTC3,ATC4b

C: ATC3b, ATC4b

C: ATC6, ATC4b, ATC4d CNC:ANTC6, ATC4b, ATC4d

C/NC: ATC6, ANTC6,ATC4b, ATC4d

C: ATC6, ATC4b, ATC4d CNC:ANTC6, ATC4b, ATC4d

C/NC: ATC6, ANTC6,ATC4b, ATC4d

C: ATC6, ATC4b, ATC4d

CNC: ANTC6, ATC4b, ATC4d

C/NC: ATC6, ANTC6, ATC4b, ATC4d

C: ATC8

CNC: ANTC8

C/NC: ANTC8, ATC8

 

Additional BC3 blocking minimum requirement

N/A

N/A

C: ATC3b

N/A

N/A

N/A

N/A

7.5

Blocking

–

–

–

–

–

–

–

 

General requirement

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3b

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6 CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC8

CNC: ANTC8

C/NC: ANTC8, ATC8

 

Co-location requirement

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3b

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6 CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC8

CNC: ANTC8

C/NC: ANTC8, ATC8

7.6

Receiver spurious emissions

–

–

–

–

–

–

–

 

General requirement

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3b

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6 CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC8

CNC: ANTC8

C/NC: ANTC8, ATC8

 

Additional requirement for BC2 (Category B)

N/A

N/A

N/A

N/A

N/A

N/A

N/A

7.7

Receiver intermodulation

–

–

–

–

–

–

–

 

General intermodulation requirement

C: ATC3a CNC: ANTC3 C/NC: ATC3a, ANTC3

C: ATC3a CNC ANTC3 C/NC: ATC3a, ANTC3

C: ATC3b

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC6

CNC ANTC6 C/NC: ATC6, ANTC6

C: ATC6

CNC: ANTC6 C/NC: ATC6, ANTC6

C: ATC8

CNC: ANTC8

C/NC: ANTC8, ATC8

 

General narrowband intermodulation requirement

C: ATC3a, ATC4b CNC:ANTC3, ATC4b C/NC: ATC3a, ANTC3, ATC4b

C: ATC3a ATC4b CNC:ANTC3,ATC4b C/NC: ATC3a, ANTC3; ATC4b

C: ATC3b, ATC4b

C: ATC6, ATC4b, ATC4d CNC:ANTC6, ATC4b, ATC4d

C/NC: ATC6, ANTC6, ATC4b, ATC4d

C: ATC6 ATC4b, ATC4d CNC:ANTC6,ATC4b, ATC4d

C/NC: ATC6, ANTC6; ATC4b, ATC4d

C: ATC6, ATC4b, ATC4d

CNC: ANTC6 , ATC4b, ATC4d

C/NC: ATC6, ANTC6, ATC4b, ATC4d

C: ATC8

CNC: ANTC8

C/NC: ANTC8, ATC8

7.8

In-channel selectivity

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

–

–

–

–

E-UTRA requirement

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

NR requirement

N/A

N/A

N/A

SC

SC

SC

SC

NOTE 1: Compliance stated by manufacturer declaration.

NOTE 2: For Operating band unwanted emissions, NR shall also be tested with SC with widest supported channel bandwidth and highest supported sub-carrier spacing.

5.3 Test configurations for multi-carrier capable TAB connector(s) in operating bands where one RAT capability sets are supported

5.3.1 General

A TAB connector may support only one RAT operation in an operating band by fulfilling different sets of requirements. Both UTRA and E-UTRA have two complete sets of requirements that may be fulfilled depending on whether the TAB connector is declared to be MSR or single RAT in the operating band. MSR and single RAT requirements are addressed separately by separate test requirements (and corresponding core requirements). They are also identified by different capability sets as described in clauses 4.11 and 5.2.

5.3.2 TAB connector supporting one RAT only MSR in the operating band

This clause contains test configuration applicability to requirements and capability sets for TAB connectors supporting one RAT only MSR operation operating with multiple carriers (MC).

Table 5.3.2-1: Test configuration applicability to requirements and
capability sets for TAB connectors supporting one RAT only MSR operation

Capability Set

UTRA (MC) capable BS (CSA1)

E-UTRA (MC) capable BS (CSA2)

TAB connector test case

BC1

BC2

BC3

BC1

BC2

BC3

6.2

Base Station output power

–

–

–

–

–

–

6.2.2

Base Station maximum output power

C: ATC1a CNC: ATC1a C/NC: ATC1a, ANTC1a

C: ATC1a CNC: ATC1a C/NC: ATC1a, ANTC1a

C: ATC1b

C: ATC2a CNC: ATC2a C/NC: ATC2a, ANTC2

C: ATC2a CNC: ATC2a C/NC: ATC2a, ANTC2

C: ATC2a CNC: ATC2a C/NC: ATC2a, ANTC2

 

Additional regional requirement (only for band 34)

N/A

N/A

N/A 

N/A

N/A

NOTE1

6.2.3

UTRA FDD primary CPICH power

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

6.2.3A

UTRA FDD secondary CPICH power

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

6.2.4

UTRA TDD primary CCPCH power

N/A

N/A

Clause 5.3.3

N/A

N/A

N/A

6.2.5

UTRA FDD additional CPICH power for MIMO mode

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

6.2.6

E-UTRA DL RS power

N/A

N/A

N/A

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

6.3

Output power dynamics

–

–

–

–

–

–

6.3.2

UTRA Inner loop power control in the downlink

N/A

N/A

N/A

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

6.3.3

Power control dynamic range

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

6.3.4

Total power dynamic range

N/A

N/A

Clause 5.3.3

N/A

N/A

N/A

6.3.5

IPDL time mask

Clause 5.3.3

Clause 5.3.3

N/A

 

 

 

6.3.6

RE Power control dynamic range

N/A

N/A

N/A

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

6.4

Transmit ON/OFF power

–

–

–

–

–

–

6.4.1

Transmitter OFF power

N/A

N/A

C: ATC1b 

N/A

N/A

C: ATC2a CNC: ATC2a C/NC: ATC2a, ANTC2

6.4.2

Transmitter transient period

N/A

N/A

C: ATC1b 

N/A

N/A

C: ATC2a CNC: ATC2a C/NC: ATC2a, ANTC2

6.5

Transmitted signal quality

–

–

–

–

–

–

6.5.2

Frequency error

–

–

–

–

–

–

 

E-UTRA

N/A

N/A

N/A

Same TC as used in clause 6.5.4

Same TC as used in clause 6.5.4

Same TC as used in clause 6.5.4

 

UTRA FDD

Same TC as used in clause 6.5.4

Same TC as used in clause 6.5.4

N/A

N/A

N/A

N/A

 

UTRA TDD

N/A

N/A

Same TC as used in clause 6.5.1

N/A

N/A

N/A

6.5.3

Time alignment error

–

–

–

–

–

–

 

E-UTRA

N/A

N/A

N/A

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

 

UTRA FDD

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

 

UTRA TDD

N/A

N/A

Clause 5.3.3

N/A

N/A

N/A

6.5.4

Modulation quality – EVM

–

–

–

–

–

–

 

E-UTRA

N/A

N/A

N/A

C: ATC2a CNC: ATC2a C/NC: ATC2a, ANTC2

C: ATC2a CNC: ATC2a C/NC: ATC2a, ANTC2

C: ATC2a CNC: ATC2aC/NC: ATC2a, ANTC2

 

UTRA FDD

C: ATC1a CNC: ATC1a C/NC: ATC1a, ANTC1a

C: ATC1a CNC: ATC1a C/NC: ATC1a, ANTC1a

N/A

N/A

N/A

N/A

 

UTRA TDD

N/A

N/A

C: ATC1b 

N/A

N/A

N/A

6.5.5

Transmit pulse shape filter

Not tested

Not tested

Not tested

Not tested

Not tested

Not tested

6.6

Unwanted Emissions

–

–

–

–

–

–

6.6.2

Occupied bandwidth

–

–

–

–

–

–

 

Minimum requirement

Clause 5.3.3

Clause 5.3.3

Clause 5.3.3

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

6.6.3

Adjacent Channel Leakage power Ratio

 

–

–

–

–

–

 

E-UTRA

N/A

N/A

N/A

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

 

UTRA FDD

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

 

UTRA TDD

N/A

N/A

Clause 5.3.3

N/A

N/A

N/A

 

Cumulative ACLR

CNC: ANTC1a C/NC: ANTC1a

CNC: ANTC1a C/NC: ANTC1a

– 

CNC: ANTC2 C/NC: ANTC2

CNC: ANTC2 C/NC: ANTC2

CNC: ANTC2 C/NC: ANTC2

6.6.4

Spectrum emission mask

 

 

 

 

 

 

6.6.5

Operating band unwanted emission

–

–

–

–

–

–

 

General requirement for Band Categories 1 and 3

Clause 5.3.3

C: ATC1a CNC: ATC1a, ANTC1a C/NC: ATC1a, ANTC1a

N/A

Clause 5.3.3

C: ATC1b 

Clause 5.3.4

C: ATC2a CNC: ATC2a, ANTC2 C/NC: ATC2a, ANTC2

N/A

Clause 5.3.4

C: ATC2a CNC: ATC2a, ANTC2 C/NC: ATC2a, ANTC2

 

General requirement for Band Category 2

N/A

Clause 5.3.3

C: ATC1a CNC: ATC1a, ANTC1a C/NC: ATC1a, ANTC1a

N/A

N/A

Clause 5.3.4

C: ATC2a CNC: ATC2a, ANTC2 C/NC: ATC2a, ANTC2

N/A

 

Additional requirements 

(note)

(note)

(note)

(note)

(note)

(note)

6.6.6

Spurious emission

–

–

–

–

–

–

 

(Category A)

C: ATC1a CNC: ANTC1a C/NC: ATC1a, ANTC1a

C: ATC1a CNC: ANTC1a C/NC: ATC1a, ANTC1a

C: ATC1b 

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

 

(Category B)

C: ATC1a CNC: ANTC1a C/NC: ATC1a, ANTC1a

C: ATC1a CNC: ANTC1a C/NC: ATC1a, ANTC1a

C: ATC1b 

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

 

Additional requirement for BC2 (Category B)

N/A

N/A

N/A

N/A

N/A

N/A 

 

Protection of the BS receiver of own or different BS

C: ATC1a CNC: ANTC1a C/NC: ATC1a, ANTC1a

C: ATC1a CNC: ANTC1a C/NC: ATC1a, ANTC1a

C: ATC1b 

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

 

Additional spurious emissions requirements

C: ATC1a CNC: ANTC1a C/NC: ATC1a, ANTC1a

C: ATC1a CNC: ANTC1a C/NC: ATC1a, ANTC1a

C: ATC1b 

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

 

Co-location with other Base Stations

C: ATC1a CNC: ANTC1a C/NC: ATC1a, ANTC1a

C: ATC1a CNC: ANTC1a C/NC: ATC1a, ANTC1a

C: ATC1b 

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2C/NC: ATC2a, ANTC2

6.7

Transmitter intermodulation

–

–

–

–

–

–

 

General requirement

Same TC as used in clause 6.6

Same TC as used in clause 6.6

Same TC as used in clause 6.6

Same TC as used in clause 6.6

Same TC as used in clause 6.6

Same TC as used in clause 6.6 

 

Additional requirement (BC1 and BC2)

CNC: ANTC1a C/NC:ANTC1a

Same TC as used in 6.6

N/A

CNC: ANTC2 C/NC: ANTC2

Same TC as used in 6.6

N/A

 

Additional requirement (BC3)

N/A

N/A

Same TC as used in clause 6.6 

N/A

N/A

Same TC as used in 6.6

7.2

Reference sensitivity level

–

–

–

–

–

–

 

E-UTRA requirement

N/A

N/A

N/A

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

 

UTRA FDD requirement

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

 

UTRA TDD requirement

N/A

N/A

Clause 5.3.3

N/A

N/A

N/A

7.3

Dynamic range

–

–

–

–

–

–

 

E-UTRA

N/A

N/A

N/A

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

 

UTRA FDD

Clause 5.3.3

Clause 5.3.3

N/A

N/A

N/A

N/A

 

UTRA TDD

N/A

N/A

Clause 5.3.3

N/A

N/A

N/A

7.4

Adjacent channel selectivity and narrowband blocking

–

–

–

–

–

–

 

General blocking requirement

C: ATC1a CNC: ANTC1a C/NC: ATC1a , ANTC1a

C: ATC1a, ATC4aCNC: ANTC1a C/NC: ATC1a , ANTC1a

C: ATC1b ATC4c

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

 

General narrowband blocking requirement

C: ATC1a, ATC4a CNC: ANTC1a, ATC4a C/NC: ATC1a, ANTC1a, ATC4a

C: ATC1a, ATC4a CNC:ANTC1a, ATC4a C/NC: ATC1a, ANTC1a, ATC4a

C: ATC1b ATC4c

C: ATC2a, ATC4b CNC:ANTC2, ATC4b C/NC: ATC2a, ANTC2

C: ATC2a, ATC4b CNC: ANTC2, ATC4b C/NC: ATC2a, ANTC2, ATC4b

C: ATC2a, ATC4b CNC: ANTC2, ATC4b C/NC: ATC2a, ANTC2, ATC4b

 

Additional BC3 blocking minimum requirement

N/A

N/A

C: ATC1b

N/A

N/A

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

7.5

Blocking

–

–

–

–

–

–

 

General requirement

C: ATC1a CNC: ANTC1a C/NC: ATC1a, ANTC1a

C: ATC1a CNC: ANTC1a C/NC: ATC1a, ANTC1a

C: ATC1b

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

 

Co-location requirement

C: ATC1a CNC: ANTC1a C/NC: ATC1a, ANTC1a

C: ATC1a CNC: ANTC1a C/NC: ATC1a, ANTC1a

C: ATC1b

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

7.6

Receiver spurious emissions

–

–

–

–

–

–

 

General requirement

C: ATC1a CNC: ANTC1a C/NC: ATC1a, ANTC1a

C: ATC1a CNC: ANTC1a C/NC: ATC1a, ANTC1a

C: ATC1b

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

 

Additional requirement for BC2 (Category B)

N/A

N/A

N/A

N/A

N/A

N/A 

7.7

Receiver intermodulation

–

–

–

–

–

–

 

General intermodulation requirement

C: ATC1a CNC: ANTC1a C/NC: ATC1a , ANTC1a

C: ATC1a CNC: ANTC1a C/NC: ATC1a , ANTC1a

C: ATC1b

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

C: ATC2a CNC: ANTC2 C/NC: ATC2a, ANTC2

 

General narrowband intermodulation requirement

C: ATC1a, ATC4a CNC:ANTC1a, ATC4a C/NC: ATC1a, ANTC1a, ATC4a

C: ATC1a, ATC4a CNC:ANTC1a, ATC4a C/NC: ATC1a, ANTC1a, ATC4a

C: ATC1b, ATC4c

C: ATC2a, ATC4b CNC: ANTC2, ATC4b C/NC: ATC2a, ANTC2, ATC4b

C: ATC2a, ATC4b CNC: ANTC2, ATC4b C/NC: ATC2a, ANTC2, ATC4b

C: ATC2a, ATC4b CNC: ANTC2, ATC4b C/NC: ATC2a, ANTC2, ATC4b

7.8

In-channel selectivity

–

–

–

–

–

–

 

E-UTRA requirement

N/A

N/A

N/A

Clause 5.3.4

Clause 5.3.4

Clause 5.3.4

NOTE: Compliance stated by manufacturer.

5.3.3 TAB connector supporting Single-RAT UTRA in the operating band

This clause contains the test configurations for TAB connectors supporting single-RAT UTRA in the operating band. The test configurations apply to TAB connectors operating with multiple carriers (MC).

For a TAB connector declared to support multi-carrier operation in contiguous spectrum operation in single band only, the test configurations in the second column of table 5.3.3-1 for FDD, and in the fifth column of table 5.3.3-1 for TDD, shall be used for testing.

NOTE: The applicability of test configurations for TDD in this clause is only applicable to UTRA TDD 1,28 Mcps option.

For FDD a TAB connector declared to support multi-carrier operation in contiguous and non-contiguous spectrum in single band and where the parameters in the manufacture’s declaration according to clause 4.10 are identical for contiguous (C) and non-contiguous (NC) spectrum operation, the test configurations in the third column of table 5.3.3‑1 shall be used for testing.

For FDD a TAB connector declared to support multi-carrier operation in contiguous and non-contiguous spectrum in single band and where the parameters in the manufacture’s declaration according to clause 4.10 are not identical for contiguous and non-contiguous spectrum operation, the test configurations in the fourth column of table 5.3.3-1 shall be used for testing.

Table 5.3.3-1: Test configurations for a TAB connector supporting single-RAT UTRA operation

TAB connector test case

Single-RAT UTRA FDD MC capable TAB connector (CSA4)
C capable only

Single-RAT UTRA FDD MC capable TAB connector (CSA4)
C and NC capable with identical parameters

Single-RAT UTRA FDD MC capable TAB connector (CSA4)
C and NC capable with different parameters

Single-RAT UTRA TDD MC capable TAB connector (CSA4)
C capable only

6.2

Base Station output power

–

–

–

 –

6.2.2

Base Station maximum output power

ATC1a

ATC1a

ATC1a, ANTC1

ATC1b

6.2.3

UTRA FDD primary CPICH power

SC

SC

SC

N/A 

6.2.3A

UTRA FDD secondary CPICH power

SC

SC

SC

 N/A 

6.2.4

UTRA TDD primary CCPCH power

N/A

N/A

N/A

SC

6.3

Output power dynamics

–

–

–

–

6.3.2

UTRA Inner loop power control in the downlink

SC

SC

SC

SC

6.3.3

Power control dynamic range

SC

SC

SC

SC

6.3.4

Total power dynamic range

SC or ATC1a

SC or ATC1a

SC or ATC1a

N/A 

6.3.5

IPDL time mask

SC

SC

SC

 N/A

6.4

Transmit ON/OFF power

 N/A

 N/A

N/A 

ATC1b

6.5

Transmitted signal quality

–

–

–

–

6.5.2

Frequency error

ATC1a

ATC1a

ATC1a, ANTC1

ATC1b

6.5.3

Time alignment error

ATC1a

ATC1a

ATC1a, ANTC1

ATC1b

6.5.4

Modulation quality – EVM

ATC1a

ATC1a

ATC1a, ANTC1

ATC1b

6.5.4

Modulation quality – PCDE

ATC1a

ATC1a

ATC1a, ANTC1

ATC1b

6.5.4

Modulation quality – RCDE

ATC1a

ATC1a

ATC1a

ATC1b

6.5.5

Transmit pulse shape filter

Not tested

Not tested

Not tested 

Not tested

6.6

Unwanted Emissions

–

–

–

–

6.6.2

Occupied bandwidth

SC

SC

SC

SC

6.6.3

Adjacent Channel Leakage power Ratio

ATC1a

ANTC1

ATC1a, ANTC1

ATC1b

 

Cumulative ACLR

–

ANTC1

ANTC1

N/A

6.6.4

Spectrum emission mask

ATC1a

ATC1a, ANTC1

ATC1a, ANTC1

ATC1b

6.6.6

Spurious emission

ATC1a

ANTC1

ATC1a, ANTC1

ATC1b

6.7

Transmitter intermodulation

ATC1a

ATC1a, ANTC1

ATC1a, ANTC1

ATC1b

7.2

Reference sensitivity level

SC

SC

SC

SC

7.3

Dynamic range

SC

SC

SC

SC

7.4

Adjacent channel selectivity and narrowband blocking

ATC1a

ANTC1

ATC1a, ANTC1

ATC1b

7.5

Blocking

ATC1a

ANTC1

ATC1a, ANTC1

ATC1b

7.6

Receiver spurious emissions

ATC1a

ANTC1

ATC1a, ANTC1

ATC1b

7.7

Receiver intermodulation

ATC1a

ANTC1

ATC1a, ANTC1

ATC1b

5.3.4 TAB connector supporting Single-RAT E-UTRA in the operating band

This clause contains the test configurations for TAB connectors supporting single-RAT E-UTRA in the operating band. The test configurations apply to TAB connectors operating with multiple carriers (MC).

For a TAB connector declared to support multi-carrier and/or CA operation in contiguous spectrum operation in single band only, the test configurations in the second column of table 5.3.4-1 shall be used for testing.

For a TAB connector declared to support multi-carrier and/or CA operation in contiguous and non-contiguous spectrum in single band and where the parameters in the manufacture’s declaration according to clause 4.10 are identical for contiguous (C) and non-contiguous (NC) spectrum operation, the test configurations in the third column of table 5.3.4-1 shall be used for testing.

For a TAB connector declared to support multi-carrier and/or CA in contiguous and non-contiguous spectrum in single band and where the parameters in the manufacture’s declaration according to clause 4.10 are not identical for contiguous and non-contiguous spectrum operation, the test configurations in the fourth column of table 5.3.4-1 shall be used for testing.

Table 5.3.4-1: Test configurations for a TAB connector supporting single-RAT E-UTRA operation capable of both contiguous and non-contiguous spectrum in multi-carrier and/or CA operation in single band

TAB connector test case

Single-RAT E-UTRA MC capable TAB connector (CSA5)

C capable only

 

Single-RAT E-UTRA MC capable TAB connector (CSA5)

C and NC capable BS with identical parameters

(CNC)

Single-RAT E-UTRA MC capable TAB connector (CSA5)

C and NC capable BS with different parameters

(CNC)

6.2

Base Station output power

–

–

–

6.2.2

Base Station maximum output power

ATC2a

ATC2a

ATC2a, ANTC2

6.2.6

E-UTRA DL RS power

SC

SC

SC

6.3

Output power dynamics

–

–

–

6.3.4

Total power dynamic range

SC

SC

SC

6.3.6

RE Power control dynamic range

Tested with Error Vector Magnitude

Tested with Error Vector Magnitude

Tested with Error Vector Magnitude

6.4

Transmit ON/OFF power

ATC2a

ATC2a

ATC2a, ANTC2

6.5

Transmitted signal quality

–

–

–

6.5.2

Frequency error

Tested with Error Vector Magnitude

Tested with Error Vector Magnitude

Tested with Error Vector Magnitude

6.5.3

Time alignment error

ATC2a

ATC2a

ATC2a, ANTC2

6.5.4

Modulation quality – EVM

ATC2a

ATC2a

ATC2a, ANTC2

6.5.5

Transmit pulse shape filter

Not Tested

Not Tested

Not Tested

6.6

Unwanted Emissions

–

–

–

6.6.2

Occupied bandwidth

SC, ATC2b (Note)

SC, ATC2b (Note)

SC, ATC2b (Note)

6.6.3

Adjacent Channel Leakage power Ratio

ATC2a

ANTC2

ATC2a, ANTC2

6.6.3

Cumulative ACLR

–

ANTC2

ANTC2

6.6.5

Operating band unwanted emission

ATC2a

ATC2a, ANTC2

ATC2a, ANTC2

6.6.6

Spurious emission

ATC2a

ANTC2

ATC2a, ANTC2

6.7

Transmitter intermodulation

ATC2a

Same TC as used in 6.6

Same TC as used in 6.6

7.2

Reference sensitivity level

SC

SC

SC

7.3

Dynamic range

SC

SC

SC

7.4

Adjacent channel selectivity and narrowband blocking

ATC2a

ANTC2

ATC2a, ANTC2

7.5

Blocking

ATC2a

ANTC2

ATC2a, ANTC2

7.6

Receiver spurious emissions

ATC2a

ANTC2

ATC2a, ANTC2

7.7

Receiver intermodulation

ATC2a

ANTC2

ATC2a, ANTC2

7.8

In-channel selectivity

SC

SC

SC

NOTE: ATC2b is only applicable when contiguous CA is supported. 

5.4 Test configurations for Multi-band TAB connectors

5.4.1 Multi-band TAB connector supporting MSR operation

Table 5.4.1-1: Test configuration for multi-band TAB connectors supporting MSR operation

TAB connector test case

Test for Multi-Band TAB connector

Test configuration for MBT

CSA1, CSA2, CSA3, CSA3A

BC1/BC2

BC3

6.2

Base Station output power

–

–

–

6.2.2

Base Station maximum output power

SBT, MBT

ATC5a

ATC5a

 

Additional regional requirement (only for band 34)

Compliance by declaration

N/A

–

6.2.3

UTRA FDD primary CPICH power

SBT

–

–

6.2.3A

UTRA FDD secondary CPICH power

 

 

 

6.2.4

UTRA TDD primary CCPCH power

SBT

–

–

6.2.5

UTRA FDD additional CPICH power for MIMO mode

 

 

 

6.2.6

E-UTRA DL RS power

E-UTRA for DL RS power

SBT

–

6.3

Output power dynamics

–

–

–

6.3.2

UTRA Inner loop power control in the downlink

SBT

–

–

6.3.3

Power control dynamic range

SBT

–

–

6.3.4

Total power dynamic range

SBT

–

N/A

6.3.5

IPDL time mask

SBT

–

N/A

6.3.6

RE Power control dynamic range

SBT

–

N/A

6.4

Transmit ON/OFF power

–

–

–

6.4.1

Transmitter OFF power

MBT, SBT (note 3)

N/A

ATC5a

6.4.2

Transmitter transient period

MBT, SBT (note 3)

N/A

ATC5a

6.5

Transmitted signal quality

–

–

–

6.5.2

Frequency error

–

–

–

 

E-UTRA

SBT, MBT

ATC5a

ATC5a

 

UTRA FDD

SBT, MBT

ATC5a

N/A

 

UTRA TDD

SBT, MBT

N/A

ATC5a 

NR

SBT, MBT

ATC5a

ATC5a

6.5.3

Time alignment error

–

–

–

 

E-UTRA

SBT, MBT (note 1)

ATC5b

ATC5b

 

UTRA FDD

SBT, MBT (note 1)

ATC5b

N/A

 

UTRA TDD

SBT

N/A

–

NR

SBT, MBT (note 1)

ATC5b

ATC5b

6.5.4

Modulation quality – EVM

–

–

–

 

E-UTRA

SBT, MBT

ATC5a

ATC5a

 

UTRA FDD

SBT, MBT

ATC5a

N/A

 

UTRA TDD

SBT, MBT

N/A

ATC5a

NR

SBT, MBT

ATC5a

ATC5a

6.5.5

Transmit pulse shape filter

Not tested

–

–

6.6

Unwanted Emissions

–

–

–

6.6.2

Occupied bandwidth

–

–

–

 

Minimum requirement

SBT

–

–

6.6.3

Adjacent Channel Leakage power Ratio

–

–

–

 

E-UTRA

SBT, MBT (note 2)

ATC5b

ATC5b

 

UTRA FDD

SBT, MBT (note 2)

ATC5b

N/A

 

UTRA TDD

SBT, MBT (note 2)

N/A

ATC5b 

 

Cumulative ACLR

SBT, MBT (note 2)

ATC5b

ATC5b 

NR

SBT, MBT (note 2)

ATC5b

ATC5b

6.6.4

Spectrum emission mask

–

–

–

6.6.5

Operating band unwanted emission

–

–

–

 

General requirement for Band Categories 1 and 3

SBT, MBT

ATC5b

ATC5b 

 

General requirement for Band Category 2

SBT, MBT

ATC5b

N/A

 

Additional requirements 

SBT, MBT

–

–

6.6.6

Spurious emission

–

–

–

 

(Category A)

SBT, MBT

ATC5b

ATC5b 

 

(Category B)

SBT, MBT

ATC5b

ATC5b 

 

Additional requirement for BC2 (Category B)

SBT, MBT

ATC5b

ATC5b 

 

Protection of the BS receiver of own or different BS

SBT, MBT

ATC5b

ATC5b 

 

Additional spurious emissions requirements

SBT, MBT

ATC5b

ATC5b 

 

Co-location with other Base Stations

–

–

–

6.7

Transmitter intermodulation

–

–

–

 

General requirement

SBT

–

–

 

Additional requirement (BC1 and BC2)

SBT

–

N/A

 

Additional requirement (BC3)

SBT

N/A

–

7.2

Reference sensitivity level

–

–

–

 

E-UTRA requirement

SBT

–

–

 

UTRA FDD requirement

SBT

–

–

 

UTRA TDD requirement

SBT

–

–

NR

SBT

–

–

7.3

Dynamic range

–

–

–

 

E-UTRA

SBT

–

–

 

UTRA FDD

SBT

–

–

 

UTRA TDD

SBT

–

–

NR

SBT

–

–

7.4

Adjacent channel selectivity and narrowband blocking

–

–

–

 

General blocking requirement

MBT, SBT (note 3)

ATC5b

ATC5b 

 

General narrowband blocking requirement

MBT, SBT (note 3)

ATC5b

ATC5b 

 

Additional BC3 blocking minimum requirement

MBT, SBT (note 3)

N/A

ATC5b 

7.5

Blocking

–

–

–

 

General requirement

MBT, SBT(note 3)

ATC5b

ATC5b 

 

Co-location requirement

MBT, SBT(note 3)

ATC5b

ATC5b 

7.6

Receiver spurious emissions

–

–

–

 

General requirement

SBT, MBT

ATC5b

ATC5b 

 

Additional requirement for BC2 (Category B)

–

–

–

7.7

Receiver intermodulation

–

–

–

 

General intermodulation requirement

MBT, SBT(note 3)

ATC5b

ATC5b 

 

General narrowband intermodulation requirement

MBT, SBT(note 3)

ATC5b

ATC5b 

7.8

In-channel selectivity

–

–

–

 

E-UTRA requirement

SBT

–

–

NR requirement

SBT

.

.

NOTE 1: MBT is only applicable when DB-DC-HSDPA/inter-band CA is supported.

NOTE 2: For ACLR, MBT shall be applied for the Inter RF bandwidth gap only.

NOTE 3: SBT is only applicable if different Capability Sets are declared for single-band and multi-band operation.

5.4.2 Multi-band TAB connector supporting Single-RAT only

For a multi-band TAB connector supporting single-RAT only in the operational band, the test configurations in table 5.4.2-1, shall be used for testing.

Table 5.4.2-1: Test configuration for multi-band TAB connectors supporting Single-RAT only

TAB connector test case

UTRA FDD CSA4

UTRA TDD CSA4

E-UTRA Test CSA5

6.2

Base Station output power

–

–

–

6.2.2

Base Station maximum output power

ATC1a/ANTC1 (note 1) ATC5a

ATC1b (note 3), ATC5a

ATC2a/ANTC2 (note 5), ATC5a

6.2.3

UTRA FDD primary CPICH power

SC

N/A

N/A

6.2.3A

UTRA FDD secondary CPICH power

SC

N/A

N/A

6.2.4

UTRA TDD primary CCPCH power

N/A

SC

N/A

6.2.5

UTRA FDD additional CPICH power for MIMO mode

SC

N/A

N/A

6.2.6

E-UTRA DL RS power

N/A

N/A

SC

6.3

Output power dynamics

–

–

–

6.3.2

UTRA Inner loop power control in the downlink

SC

SC

N/A

6.3.3

Power control dynamic range

SC

SC

SC

6.3.4

Total power dynamic range

SC or ATC1a

N/A

SC

6.3.5

IPDL time mask

SC

N/A

N/A

6.3.6

RE Power control dynamic range

N/A

N/A

Tested with Error Vector Magnitude

6.4

Transmit ON/OFF power

–

–

–

6.4.1

Transmitter OFF power

N/A

ATC5a

ATC5a (only applied for E‑UTRA TDD BS)

6.4.2

Transmitter transient period

N/A

SC

SC

6.5

Transmitted signal quality

–

–

–

6.5.2

Frequency error

Tested with EVM

ATC1b (note 3), ATC5a

Tested with Error Vector Magnitude

6.5.3

Time alignment error

ATC1a/ANTC1 (note 1) ATC5b

ATC1b (note 3)

ATC2a/ANTC2 (note 5), ATC5b (note 6)

6.5.4

Modulation quality – EVM

ATC1a/ANTC1 (note 1), ATC5a

ATC1b (note 3), ATC5a

ATC2a/ANTC2 (note 5), ATC5a

6.5.4

Modulation quality – PCDE

ATC1a/ANTC1 (note 1)

ATC1b (note 3), ATC5a

N/A

6.5.4

Modulation quality – RCDE

AUTC1

ATC1b (note 3), ATC5a

N/A

6.5.5

Transmit pulse shape filter

not tested

not tested

not tested

6.6

Unwanted Emissions

–

–

–

6.6.2

Occupied bandwidth

SC

SC

SC, ATC2b (note 7)

6.6.3

Adjacent Channel Leakage power Ratio

ATC1a/ANTC1 (note 1) ATC5b (note 2)

ATC1b (note 3), ATC5a (note 4)

ATC2a/ANTC2 (note 5), ATC5b (note 8)

6.6.4

Spectrum emission mask

ATC1a/ANTC1 (note 1) ATC5b

ATC1b (note 3), ATC5a

N/A

6.6.5

Operating band unwanted emission

N/A

N/A

ATC2a/ANTC2 (note 5), ATC5b

6.6.6

Spurious emission

ATC1a/ANTC1 (note 1) ATC5b

ATC1b (note 3), ATC5a

ATC2a/ANTC2 (note 5), ATC5b

6.7

Transmitter intermodulation

ATC1a/ANTC1 (note 1)

ATC1b (note 3)

ATC2a/ANTC2 (note 5)

7.2

Reference sensitivity level

SC

SC

SC

7.3

Dynamic range

SC

SC

SC

7.4

Adjacent channel selectivity and narrowband blocking

ATC5b

ATC5a

ATC5b

7.5

Blocking

ATC5b

ATC5a

ATC5b

7.6

Receiver spurious emissions

ATC1a/ANTC1 (note 1) ATC5b

ATC1b (note 3), ATC5a

ATC2a/ANTC2 (note 5), ATC5b

7.7

Receiver intermodulation

ATC5b

ATC5a

ATC5b

7.8

In-channel selectivity

N/A

N/A

SC

NOTE 1: ATC1a and/or ANTC1 shall be applied in each supported operating band according to table 5.3.3-1.

NOTE 2: ATC5b may be applied for Inter RF Bandwidth gap only.

NOTE 3: ATC1b shall be applied in each supported operating band according to table 5.3.3-1.

NOTE 4: ATC5a may be applied for Inter RF bandwidth gap only.

NOTE 5: ATC2 and/or ANTC2 shall be applied in each supported operating band according to table 5.3.4-1.

NOTE 6: ATC5b is only applicable when inter-band CA is supported.

NOTE 7: ATC2b is only applicable when contiguous CA is supported.

NOTE 8: ATC5b may be applied for Inter RF bandwidth gap only.