6 Transmitter total radiated power
37.1443GPPRelease 17TSUser Equipment (UE) and Mobile Station (MS) GSM, UTRA and E-UTRA over the air performance requirements
6.1 Minimum requirement for roaming bands for handheld UE
The average measured total radiated power (TRP) of low, mid and high channel for handheld UE shall be higher than the average TRP requirement specified in subclauses 6.1.1, 6.1.2 and 6.1.3. The averaging shall be done in linear scale for the TRP results of both right and left side of the phantom head in case of beside the head phantom and beside the head and hand phantom positions. For the hand phantom browsing mode position the averaging shall be done in linear scale for the TRP results of both right and left hand phantom measurements. Average TRP requirement is shown in the column “Average” on the requirement tables.
In addition the lowest TRP of each measured channel shall be higher than minimum TRP requirement specified in subclauses 6.1.1, 6.1.2 and 6.1.3. Minimum TRP requirement is shown in the column “Min” on the requirement tables.
6.1.1 Beside the head phantom position
Beside the head phantom test method is defined in TR 25.914 [6] subclauses 5.1.1 and 5.1.2.
6.1.1.1 GSM
Handheld MS TRP minimum performance requirements for GMSK in beside the head phantom position and the primary mechanical mode are defined in Table 6.1.1.1-1.
Table 6.1.1.1-1: Handheld UE TRP minimum performance requirement for GSM roaming bands in beside the head phantom position and the primary mechanical mode
Operating band |
Power class 1 |
Power class 2 |
Power class 3 |
Power class 4 |
Power class 5 |
|||||
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
||||||
Average |
Min |
Average |
Min |
Average |
Min |
Average |
Min |
Average |
Min |
|
GSM 850 |
19,5 |
17,5 |
||||||||
GSM 900 |
20,5 |
18,5 |
||||||||
DCS 1800 |
21 |
19 |
||||||||
PCS 1900 |
21 |
19 |
||||||||
NOTE: Applicable for dual-mode GSM/UMTS. |
6.1.1.2 UTRA FDD
Handheld UE TRP minimum performance requirements for UTRA FDD in beside the head phantom position and the primary mechanical mode are defined in Table 6.1.1.2-1.
Table 6.1.1.2-1: Handheld UE TRP minimum performance requirement for UTRA FDD roaming bands in beside the head phantom position and the primary mechanical mode
Operating band |
Power class 1 |
Power class 2 |
Power class 3 |
Power class 3bis |
Power class 4 |
|||
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
||||
Average |
Min |
Average |
Min |
Average |
Min |
|||
I |
– |
– |
+15 |
+13 |
+15 |
+13 |
+13 |
+11 |
II |
– |
– |
+15 |
+13 |
+15 |
+13 |
+13 |
+11 |
III |
– |
– |
+15 |
+13 |
+15 |
+13 |
+13 |
+11 |
IV |
– |
– |
+15 |
+13 |
+15 |
+13 |
+13 |
+11 |
V |
– |
– |
+11 |
+9 |
+11 |
+9 |
+9 |
+7 |
VI |
– |
– |
+11 |
+9 |
+11 |
+9 |
+9 |
+7 |
VII |
– |
– |
+15 |
+13 |
+15 |
+13 |
+13 |
+11 |
VIII |
– |
– |
+12 |
+10 |
+12 |
+10 |
+10 |
+8 |
IX |
– |
– |
+15 |
+13 |
+15 |
+13 |
+13 |
+11 |
XIX |
– |
– |
+11,5 |
+9,5 |
+11,5 |
+9,5 |
+9,5 |
+7,5 |
NOTE: Applicable for dual-mode GSM/UMTS. |
6.1.1.3 UTRA LCR TDD
Handheld UE TRP minimum performance requirements for UTRA LCR TDD in beside the head phantom position and the primary mechanical mode are defined in Table 6.1.1.3-1.
Table 6.1.1.3-1: Handheld UE TRP minimum performance requirement for UTRA LCR TDD roaming bands in beside the head phantom position and the primary mechanical mode
Operating band |
Power class 1 |
Power class 2 |
Power class 3 |
Power class 4 |
||||
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
|||||
Average |
Min |
Average |
Min |
Average |
Min |
Average |
Min |
|
a |
- |
- |
+15 |
+13 |
- |
- |
- |
- |
b |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
c |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
d |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
e |
- |
- |
+15 |
+13 |
- |
- |
- |
- |
f |
- |
- |
+15 |
+13 |
- |
- |
- |
- |
NOTE: Applicable for dual-mode GSM /UTRA LCR TDD. |
6.1.2 Beside the head and hand phantom position
Beside the head and hand phantom position is defined in TR 25.914 [6] subclauses 5.1.5 and 5.1.6.
6.1.2.1 UTRA FDD
Handheld UE TRP minimum performance requirements for UTRA FDD in beside the head and hand phantom position and the primary mechanical mode are defined in Table 6.1.2.1-1.
Table 6.1.2.1-1: Handheld UE TRP minimum performance requirement for FDD roaming bands in beside the head and hand phantom position and the primary mechanical mode
Operating band |
Power class 1 |
Power class 2 |
Power class 3 |
Power class 3bis |
Power class 4 |
|||
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
||||
Average |
Min |
Average |
Min |
Average |
Min |
|||
I |
– |
– |
13,25 |
TBD |
TBD |
TBD |
TBD |
TBD |
II |
– |
– |
13,25 |
TBD |
TBD |
TBD |
TBD |
TBD |
III |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
IV |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
V |
– |
– |
9,40 |
TBD |
TBD |
TBD |
TBD |
TBD |
VI |
– |
– |
9,40 |
TBD |
TBD |
TBD |
TBD |
TBD |
VII |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
VIII |
– |
– |
9,40 |
TBD |
TBD |
TBD |
TBD |
TBD |
IX |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
XIX |
9,40 |
TBD |
TBD |
TBD |
TBD |
TBD |
||
NOTE 1: Applicable for dual-mode GSM/UMTS. NOTE 2: Applicable for devices narrower than 72mm as defined in TR 25.914. NOTE 3: Not applicable for devices supporting CDMA or aggregated carriers (e.g. multi-carrier HSPA, LTE Carrier Aggregation). |
6.1.2.2 UTRA LCR TDD
Handheld UE TRP minimum performance requirements for UTRA LCR TDD in beside the head and hand phantom position and the primary mechanical mode are defined in Table 6.1.2.2-1.
Table 6.1.2.2-1: Handheld UE TRP minimum performance requirement for UTRA LCR TDD roaming bands beside the head and hand phantom position and the primary mechanical mode
Operating band |
Power class 1 |
Power class 2 |
Power class 3 |
Power class 4 |
||||
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
|||||
Average |
Min |
Average |
Min |
Average |
Min |
Average |
Min |
|
a |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
b |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
c |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
d |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
e |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
f |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
NOTE: Applicable for dual-mode GSM /UTRA LCR TDD. |
6.1.2.3 E-UTRA FDD
6.1.2.4 E-UTRA TDD
6.1.3 Hand phantom browsing mode position
Hand phantom browsing mode position is defined in TR 25.914 [6] subclauses 5.1.5 and 5.1.7.
6.1.3.1 UTRA FDD
Handheld UE TRP minimum performance requirements for UTRA FDD in hand phantom browsing mode position are defined in Table 6.1.3.1-1.
Table 6.1.3.1-1: Handheld UE TRP minimum performance requirement for UTRA FDD roaming bands in hand phantom browsing mode position
Operating band |
Power class 1 |
Power class 2 |
Power class 3 |
Power class 3bis |
Power class 4 |
|||
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
||||
Average |
Min |
Average |
Min |
Average |
Min |
|||
I |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
II |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
III |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
IV |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
V |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
VI |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
VII |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
VIII |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
IX |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
XIX |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
||
NOTE: Applicable for dual-mode GSM/UMTS. |
6.1.3.2 UTRA LCR TDD
Handheld UE TRP minimum performance requirements for UTRA LCR TDD UE in hand phantom browsing mode position are defined in Table 6.1.3.2-1.
Table 6.1.3.2-1: Handheld UE TRP minimum performance requirement for UTRA LCR TDD roaming bands in hand phantom browsing mode position
Operating band |
Power class 1 |
Power class 2 |
Power class 3 |
Power class 4 |
||||
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
|||||
Average |
Min |
Average |
Min |
Average |
Min |
Average |
Min |
|
a |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
b |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
c |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
d |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
e |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
f |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
NOTE: Applicable for dual-mode GSM /UTRA LCR TDD. |
6.1.3.3 E-UTRA FDD
6.1.3.4 E-UTRA TDD
6.2 Minimum requirement for roaming bands for LME
The average measured TRP of low, mid and high channel for laptop mounted equipment shall be higher than the average TRP requirement specified in this subclause. The averaging shall be done in linear scale for the TRP results. Average TRP requirement is shown in the column “Average” on the requirement tables.
In addition the lowest TRP of each measured channel shall be higher than minimum TRP requirement specified in this subclause. Minimum TRP requirement is shown in the column “Min” on the requirement tables.
LME requirements in this clause are defined to be measured with laptop ground plane phantom as defined in TR 25.914 [6] subclauses 5.1.3 and 5.1.4.
6.2.1 GSM
LME TRP minimum performance requirements for GSM with laptop ground plane phantom in data transfer position are defined in Table 6.2.1-1.
Table 6.2.1-1: LME TRP minimum performance requirement for GSM in the data transfer position
Operating band |
Power class 1 |
Power class 2 |
Power class 3 |
Power class 4 |
Power class 5 |
|||||
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
||||||
Average |
Min |
Average |
Min |
Average |
Min |
Average |
Min |
Average |
Min |
|
GSM 850 |
– |
– |
– |
– |
– |
– |
TBD |
TBD |
– |
– |
GSM 900 |
– |
– |
– |
– |
– |
– |
TBD |
TBD |
– |
– |
DCS 1800 |
TBD |
TBD |
– |
– |
– |
– |
– |
– |
– |
– |
PCS 1900 |
TBD |
TBD |
– |
– |
– |
– |
– |
– |
– |
– |
NOTE 1: Applicable for dual-mode GSM/UMTS. NOTE 2: Applicable for USB plug-in devices. |
6.2.2 UTRA FDD
LME TRP minimum performance requirements for UTRA FDD with laptop ground plane phantom in data transfer position are defined in Table 6.2.2-1.
Table 6.2.2-1: LME TRP minimum performance requirement for UTRA FDD in the data transfer position
Operating band |
Power class 1 |
Power class 2 |
Power class 3 |
Power class 3bis |
Power class 4 |
|||
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
||||
Average |
Min |
Average |
Min |
Average |
Min |
|||
I |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
II |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
III |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
IV |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
V |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
VI |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
VII |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
VIII |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
IX |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
XIX |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
||
NOTE 1: Applicable for dual-mode GSM/UMTS. NOTE 2: Applicable for USB plug-in devices. |
6.2.3 UTRA LCR TDD
LME TRP minimum performance requirements for UTRA LCR TDD with laptop ground plane phantom in data transfer position are defined in Table 6.2.3-1.
Table 6.2.3-1: LME TRP minimum performance requirement for UTRA LCR TDD in the data transfer position
Operating band |
Power class 1 |
Power class 2 |
Power class 3 |
Power class 4 |
||||
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
|||||
Average |
Min |
Average |
Min |
Average |
Min |
Average |
Min |
|
a |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
b |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
c |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
d |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
e |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
f |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
NOTE 1: Applicable for dual-mode GSM /UTRA LCR TDD. NOTE 2: Applicable for USB plug-in devices. |
6.2.4 E-UTRA FDD
6.2.5 E-UTRA TDD
6.3 Minimum requirement for roaming bands for LEE
The average measured TRP of low, mid and high channel for laptop embedded equipment shall be higher than the average TRP requirement specified in this subclause. The averaging shall be done in linear scale for the TRP results. Average TRP requirement is shown in the column “Average” on the requirement tables.
In addition the lowest TRP of each measured channel shall be higher than minimum TRP requirement specified in this subclause. Minimum TRP requirement is shown in the column “Min” on the requirement tables.
LEE requirements in this clause are defined to be measured as defined in TR 25.914 [6]: subclause 5.3.1 applies to notebook devices, and subclause 5.3.2 applies to tablet devices.
6.3.1 GSM
LEE TRP minimum performance requirements for GSM are defined in Tables 6.3.1-1 and 6.3.1-2.
Table 6.3.1-1: Notebook TRP minimum performance requirement for GSM in the data transfer position
Operating band |
Power class 1 |
Power class 2 |
Power class 3 |
Power class 4 |
Power class 5 |
|||||
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
||||||
Average |
Min |
Average |
Min |
Average |
Min |
Average |
Min |
Average |
Min |
|
GSM 850 |
– |
– |
– |
– |
– |
– |
TBD |
TBD |
– |
– |
GSM 900 |
– |
– |
– |
– |
– |
– |
TBD |
TBD |
– |
– |
DCS 1800 |
TBD |
TBD |
– |
– |
– |
– |
– |
– |
– |
– |
PCS 1900 |
TBD |
TBD |
– |
– |
– |
– |
– |
– |
– |
– |
NOTE 1: Applicable for dual-mode GSM/UMTS. NOTE 2: Applicable for notebook devices. |
Table 6.3.1-2: Tablet TRP minimum performance requirement for GSM in the data transfer position
Operating band |
Power class 1 |
Power class 2 |
Power class 3 |
Power class 4 |
Power class 5 |
|||||
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
||||||
Average |
Min |
Average |
Min |
Average |
Min |
Average |
Min |
Average |
Min |
|
GSM 850 |
– |
– |
– |
– |
– |
– |
TBD |
TBD |
– |
– |
GSM 900 |
– |
– |
– |
– |
– |
– |
TBD |
TBD |
– |
– |
DCS 1800 |
TBD |
TBD |
– |
– |
– |
– |
– |
– |
– |
– |
PCS 1900 |
TBD |
TBD |
– |
– |
– |
– |
– |
– |
– |
– |
NOTE 1: Applicable for dual-mode GSM/UMTS. NOTE 2: Applicable for tablet devices. |
6.3.2 UTRA FDD
LEE TRP minimum performance requirements for UTRA FDD are defined in Tables 6.3.2-1 and 6.3.2-2.
Table 6.3.2-1: Notebook TRP minimum performance requirement for UTRA FDD in the data transfers position
Operating band |
Power class 1 |
Power class 2 |
Power class 3 |
Power class 3bis |
Power class 4 |
|||
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
||||
Average |
Min |
Average |
Min |
Average |
Min |
|||
I |
– |
– |
19,0 |
17,5 |
TBD |
TBD |
TBD |
TBD |
II |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
III |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
IV |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
V |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
VI |
– |
– |
18,5 |
16,5 |
TBD |
TBD |
TBD |
TBD |
VII |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
VIII |
– |
– |
18,5 |
16,5 |
TBD |
TBD |
TBD |
TBD |
IX |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
XIX |
18,5 |
16,5 |
TBD |
TBD |
TBD |
TBD |
||
NOTE 1: Applicable for multi-mode GSM/UMTS/LTE. NOTE 2: Applicable for notebook devices. |
NOTE: TRP minimum performance requirements in table 6.3.2-1 apply to HSPA and LTE UEs supporting only single carrier operation. Their applicability to multi-carrier operation is FFS. This is because it has not been verified whether the UEs measured to derive the requirements supported carrier aggregation or not.
Table 6.3.2-2: Tablet TRP minimum performance requirement for UTRA FDD in the data transfer position
Operating band |
Power class 1 |
Power class 2 |
Power class 3 |
Power class 3bis |
Power class 4 |
|||
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
||||
Average |
Min |
Average |
Min |
Average |
Min |
|||
I |
– |
– |
19 |
17,5 |
TBD |
TBD |
TBD |
TBD |
II |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
III |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
IV |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
V |
– |
– |
17 |
15,0 |
TBD |
TBD |
TBD |
TBD |
VI |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
VII |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
VIII |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
IX |
– |
– |
TBD |
TBD |
TBD |
TBD |
TBD |
TBD |
XIX |
17 |
15,0 |
TBD |
TBD |
TBD |
TBD |
||
NOTE 1: Applicable for dual-mode GSM/UMTS. NOTE 2: Applicable for tablet devices with two antennas. |
6.3.3 UTRA LCR TDD
LEE TRP minimum performance requirements for UTRA LCR TDD are defined in Tables 6.3.3-1 and 6.3.3-2.
Table 6.3.3-1: Notebook TRP minimum performance requirement for UTRA LCR TDD in the data transfer position
Operating band |
Power class 1 |
Power class 2 |
Power class 3 |
Power class 4 |
||||
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
|||||
Average |
Min |
Average |
Min |
Average |
Min |
Average |
Min |
|
a |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
b |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
c |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
d |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
e |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
f |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
NOTE 1: Applicable for dual-mode GSM /UTRA LCR TDD. NOTE 2: Applicable for notebook devices. |
Table 6.3.3-2: Tablet TRP minimum performance requirement for UTRA LCR TDD in the data transfer position
Operating band |
Power class 1 |
Power class 2 |
Power class 3 |
Power class 4 |
||||
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
|||||
Average |
Min |
Average |
Min |
Average |
Min |
Average |
Min |
|
a |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
b |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
c |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
d |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
e |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
f |
- |
- |
TBD |
TBD |
- |
- |
- |
- |
NOTE 1: Applicable for dual-mode GSM /UTRA LCR TDD. NOTE 2: Applicable for tablet devices. |
6.3.4 E-UTRA FDD
LEE TRP minimum performance requirements for E-UTRA FDD are defined in Table 6.3.4-1 for Tablet devices.
Table 6.3.4-1: Tablet TRP minimum requirements for E-UTRA FDD in the data transfer position
Operating band |
Power Class 1 |
Power Class 2 |
Power Class 3 |
Power Class 4 |
|
Power (dBm) |
Power (dBm) |
Power (dBm) |
Power (dBm) |
||
Average |
Min |
||||
1 |
18.5 |
17.0 |
|||
2 |
|||||
3 |
18.5 |
17.0 |
|||
4 |
|||||
5 |
|||||
7 |
18.0 |
16.5 |
|||
8 |
|||||
12 |
|||||
13 |
|||||
19 |
17.5 |
15.5 |
|||
20 |
17.5 |
15.5 |
|||
21 |
17.5 |
16.0 |
|||
28 |
|||||
NOTE 1: Applicable for multi-mode GSM/UMTS/LTE. NOTE 2: Applicability for devices supporting CDMA or aggregated carriers (e.g. multi-carrier HSPA, LTE Carrier Aggregation) is FFS. |