11 Radiated performance requirements
37.1053GPPActive Antenna System (AAS) Base Station (BS) transmission and receptionRelease 17TS
11.1 General
11.1.1 OTA demodulation branches
OTA performance requirements are only specified for up to 2 demodulation branches.
If the OTA AAS BS uses polarization diversity and has the ability to maintain isolation between the signals for each of the demodulation branches, then OTA performance requirements can be tested for up to two demodulation branches. When tested for two demodulation branches, each demodulation branch maps to one polarization.
If the OTA AAS BS does not use polarization diversity then OTA performance requirements can only be tested for a single demodulation branch.
11.1.2 UTRA operation
Performance requirements for single RAT UTRA operation in FDD are specified for the measurement channels defined in 3GPP TS 25.104 [2]. The requirements only apply to those measurement channels that are supported by AAS BS. For FRC8 in 3GPP TS 25.104 [2] the non E-DPCCH boosting and E-DPCCH boosting requirement only apply for the option supported by the AAS BS. The performance requirements for the high speed train scenarios defined in 3GPP TS 25.104 [2] are optional.
Unless stated otherwise, performance requirements apply for a single cell only. Performance requirements for an AAS BS supporting UTRA FDD DC-HSUPA or DB-DC-HSUPA and UTRA TDD MC_HSUPA are defined in terms of single carrier requirements. For FDD operation the requirements in clause 11 shall be met with the transmitter unit(s) associated with the RIB in the operating band ON.
NOTE: In normal operating conditions the transceiver units in UTRA FDD operation are configured to transmit and receive at the same time. The transmitter unit(s) associated with the RIB may be OFF for some of the tests as specified in 3GPP TS 37.145 [13].
In the referred UTRA specifications and in this clause, the term BS with RX diversity refers to performance requirements for two demodulation branches, and BS without RX diversity refers to performance requirements for one demodulation branch.
For AAS BS with RX diversity, only the BS performance requirements with RX diversity apply, the required Eb/N0 for UTRA FDD and Îor/Ioc for UTRA TDD shall be applied separately for each demodulation branch.
For AAS BS without RX diversity, only the BS performance requirements without RX diversity apply. The required Eb/N0 for UTRA FDD and Îor/Ioc for UTRA TDD shall be applied for each AAS BS demodulation branch.
The Eb/N0 used for UTRA FDD is defined as:
Where:
is the received total energy of DPDCH, DPCCH, S-DPCCH, HS-DPCCH, E-DPDCH, S-E-DPDCH, E-DPCCH and S-E-DPCCH per PN chip per demodulation branch from all branches
is the total one-sided noise power spectral density due to all noise sources
is the number of chips per frame
is the number of information bits in DTCH excluding CRC bits per frame
Table 11.1.2-1: Summary of AAS BS performance targets for single RAT UTRA operation
|
Physical channel |
Measurement channel |
Static |
Multi-path Case 1 |
Multi-path Case 2 |
Multi-path Case 3 |
Moving |
Birth / Death |
High Speed Train |
|
Performance metric |
||||||||
|
DCH |
12.2 kbps |
BLER<10-2 |
BLER<10-2 |
BLER<10-2 |
BLER<10-2 |
BLER<10-2 |
BLER<10-2 |
BLER<10-2 |
|
64 kbps |
BLER< 10-1,10-2 |
BLER< 10-1, 10-2 |
BLER< 10-1,10-2 |
BLER< 10-1, 10-2,10-3 |
BLER< 10-1,10-2 |
BLER< 10-1,10-2 |
– |
|
|
144 kbps |
BLER< 10-1,10-2 |
BLER< 10-1,10-2 |
BLER< 10-1,10-2 |
BLER< 10-1, 10-2,10-3 |
– |
– |
– |
|
|
384 kbps |
BLER< 10-1,10-2 |
BLER< 10-1,10-2 |
BLER< 10-1,10-2 |
BLER< 10-1, 10-2,10-3 |
– |
– |
– |
|
|
NOTE: In case of multiple BLER level thresholds listed for single requirement and measurement cannel combination, those BLER level values are reflected by set multiple requirements in 3GPP TS 25.104 [2]. |
||||||||
11.1.3 E-UTRA operation
Performance requirements for the AAS BS are specified for the fixed reference channels (FRC) and propagation conditions defined in 3GPP TS 36.104 [8] annex A and annex B, respectively. The requirements only apply to those FRCs that are supported by the AAS BS.
Unless stated otherwise, performance requirements apply for a single carrier only. Performance requirements for an AAS BS E-UTRA supporting carrier aggregation are defined in terms of single carrier requirements. For FDD operation the requirements shall be met with the transmitter unit(s) associated with the RIB in the operating band ON.
NOTE: In normal operating conditions the transceiver units in FDD operation are configured to transmit and receive at the same time. The transmitter unit(s) associated with the RIB may be OFF for some of the tests as specified in 3GPP TS 37.145 [13].
In the referred E-UTRA specification, the term "RX antennas" refers to demodulation branches (and not physical antennas).
The SNR used in this clause is specified based on a single carrier and defined as:
SNR = S / N
Where:
S is the total signal energy in the subframe.
N is the noise energy in a bandwidth corresponding to the transmission bandwidth over the duration of a subframe.
For enhanced performance requirements type A, the SINR used in this clause is specified based on a single carrier and defined as:
Where:
is the total signal energy in the subframe.
is the summation of the received energy of the strongest interferers explicitly defined in a test procedure plus the white noise energy N, in a bandwidth corresponding to the transmission bandwidth over the duration of a subframe. The respective energy of each interferer relative to 
is defined by its associated DIP value.
11.2 Minimum requirements for MSR operation
For single RAT UTRA operation, minimum requirements for demodulation performance are specified in subclause 8.3.
For single RAT E-UTRA operation, minimum requirements for demodulation performance are specified in subclause 8.4.
11.3 Minimum requirements for UTRA operation
The single RAT UTRA operation in FDD shall fulfil all mandatory BS demodulation performance requirements specified in subclauses 8.2 to 8.12 of 3GPP TS 25.104 [6].
In the referred UTRA specifications, the term BS with RX diversity refers to performance requirements for two demodulation branches, and BS without RX diversity refers to performance requirements for one demodulation branch.
11.4 Minimum requirements for E-UTRA operation
The single RAT E-UTRA operation shall fulfil all mandatory BS demodulation performance requirements specified in subclauses 8.2 – 8.4 (for PUSCH, PUCCH and PRACH) and 8.6 – 8.7 (for subslot-PUSCH and sPUCCH) of TS 36.104 [8].
In the referred E-UTRA specification, the term "RX antennas" refers to demodulation branches (i.e. not physical antennas).
Annex A (normative):
Environmental requirements for the BS equipment
The AAS BS equipment shall fulfil all the requirements in the full range of environmental conditions for the relevant environmental class. The environmental conditions and class shall be from the relevant IEC specifications or the corresponding ETSI specifications listed below.
IEC specifications for environmental requirements:
IEC 60721-3-3 [21]: "Stationary use at weather protected locations".
IEC 60721-3-4 [22]: "Stationary use at non weather protected locations".
ETSI specifications for environmental requirements:
ETSI EN 300 019-1-3 [23]: "Stationary use at weather protected locations".
ETSI EN 300 019-1-4 [24]: "Stationary use at non weather protected locations".
Normally it should be sufficient for all tests to be conducted using normal test conditions except where otherwise stated. For guidance on the use of test conditions to be used in order to show compliance refer to TS 37.145-1 [29] or TS 37.145-2 [30].
Annex B (Informative):
Calculation of EIRP based on fixed assumption of passive antenna gain
B.1 Calculation of EIRP based on fixed assumption of passive antenna gain
Some regional requirements are defined per effective isotropic radiated power (EIRP), which is a combination of the transmitted power (or in some cases spectral density) and the effective antenna gain which is a site specific condition. Such requirements may be applied per antenna, per cell, or per base station. It shall be noted that the definition of BS or cell may differ between regulations. Where the regulator prescribes a method for EIRP calculation, that method supersedes the proposed assessment in this annex.
The regulations set an EIRP limit considering a passive antenna BS. Although the gain of passive antennas may vary somewhat, the gain variation is in the order of a few dBs. The instantaneous gain of an AAS BS may be much larger. However AAS unwanted emissions requirements are defined as TRP, since TRP impacts co-existence properties.
In order to relate the EIRP values in the specifications to TRP, a fixed assumption has been made on the gain of a typical passive BS antenna.
Thus, the maximum TRP can be estimated using the following formulas:
TRP limit per antenna: PTRP, antenna = PEIRP – GAnt
E-UTRA TRP limit per cell or per BS: PTRP =PTRP,antenna + 9dB
UTRA TRP limit per cell or per BS: PTRP =PTRP,antenna + 6dB
It is noted that the AAS architecture assumes that a BS subject to OTA requirements will have at least 8 antennas.
In case the TRP requirement is set per polarisation, the summation shall be made per polarisation.
"PEIRP" is the effective isotropic radiated power (or radiated power spectral density) set in the regulation (assuming a passive BS antenna) in dBm (or dBm/measurement BW).
"GAnt" is the effective antenna gain, the antenna gain (dBi) is a fixed reference value of 17 dBi. Directivity value should be used in above equations, however with all antenna losses are assumed zero then we can use effective antenna gain.
Annex C (informative):
Change history
|
Change history |
|||||||
|
Date |
Meeting |
TDoc |
CR |
Rev |
Cat |
Subject/Comment |
New version |
|
2015-10 |
RAN4#76bis |
R4-156540 |
Specification structure |
0.0.1 |
|||
|
2015-10 |
RAN4#77 |
R4-157517 |
Approved text proposals in the following documents were implemented: R4-156802 – TP – Text for TS, structure update R4-156926 – TP – Text for TS, General clauses R4-156804 – TP for TS Conducted transmitter requirements – subclause 6.5 R4-156805 – TP for TS Conducted transmitter requirements – clause 7 R4-156806 – Proposed OTA TX power TS text – clause 9 R4-156807 – TP – Text for TS, OTA sensitivity – clause 10 |
0.1.0 |
|||
|
2016-02 |
RAN4#78 |
R4-161119 |
Approved text proposals in the following documents were implemented: R4-157316 – TP for TS37.105: correction on base station classes R4-157529 – TP – Text for TS, clean up missing references R4-157657 – TP for TS 37.105: Additions to OTA sensitivity in section 10 R4-158287 – TP for TS – clean up based on modification in section 4.9 R4-158288 – TP – Text for TS, definitions clean up. R4-158289 – TP – Text for TS, General section R4-158290 – TP – Text for TS, Section 5 R4-158291 – TP – Text for TS, Conducted Transmitter Requirements – section 6, 6.1, 6.2, 6.3, 6.4 R4-158292 – TP for 37.105: Unwanted Emissions R4-158293 – TP for TS 37.105: Radiated transmit power additions to section 9 R4-158294 – TP for TS 37.105: Adding transmitter IMD requirement text to section 6.7 R4-158295 – TP for TS 37.105: Adding receiver emission scaling to section 7.6 |
0.2.0 |
|||
|
2016-02 |
RAN4#78 |
R4-161308 |
Approved text proposals in the following documents were implemented: R4-160932 – TP to TS 37.105 – EIRP accuracy value R4-160933 – TP to TS 37.105 – final clean up R4-160935 – TP-to TS 37.105 – add clarification of conformance requirements R4-160699 – TP for TS 37.105: Editorial corrections to radiated transmit power in clause 9 R4-161362 – TP for TS 37.105: AAS TS overall cleanup R4-161358 – TP for TS 37.105: Improvements to Radiated transmit power in section 3 and 9 R4-161364 – TP – to TS37.105 – Text amendment regarding multi-band exclusion bands for RX spurious emission R4-161363 – TP-to TS 37.105 – add annexes R4-161360 – TP for TS37.105 on UEM requirements R4-161236 – TP for 37.104: core specification design for AAS demodulation requirements R4-161495 – TP to 37.105 on Multi-band Tx/Rx TAB connector |
0.3.0 |
|||
|
2016-03 |
RAN#71 |
RP-160400 |
Presented to RAN for approval. Editorial cotrrections recommended by ETSI editHelp |
1.0.0 |
|||
|
2016-03 |
RP-71 |
TR is approved by RAN plenary |
13.0.0 |
||||
|
06/2016 |
RP-72 |
RP-161142 |
2 |
1 |
F |
Editorial corrections – alignment with 3GPP drafting rules |
13.1.0 |
|
06/2016 |
RP-72 |
RP-161127 |
5 |
1 |
F |
Clarifying UTRA TDD option in Performance section |
13.1.0 |
|
06/2016 |
RP-72 |
RP-161142 |
6 |
– |
F |
Correction of interfering signal level for Tx intermodulation |
13.1.0 |
|
06/2016 |
RP-72 |
RP-161142 |
7 |
1 |
F |
Correct spectrum emission mask and operating band UEM absolute basic limits |
13.1.0 |
|
06/2016 |
RP-72 |
RP-161142 |
11 |
1 |
D |
37.105: Readability improvemenand corrections (sections 4 – 10) |
13.1.0 |
|
09/2016 |
RP-73 |
RP-161635 |
15 |
|
D |
TS 37.105: Readability improvements and corrections (section 3) |
13.2.0 |
|
09/2016 |
RP-73 |
RP-161635 |
13 |
1 |
F |
Correction of AAS Base Station performance targets |
13.2.0 |
|
12/2016 |
RP-74 |
RP-162422 |
0018 |
1 |
F |
MB MSR related corrections on receiver blocking |
13.3.0 |
|
12/2016 |
RP-74 |
RP-162422 |
0020 |
2 |
D |
CR to TS 37.105: Clarifications, definitions alignment and text improvements |
13.3.0 |
|
12/2016 |
RP-74 |
RP-162422 |
0021 |
1 |
F |
TS 37.105: Removal of operating band unwanted emissions for Band 46 |
13.3.0 |
|
12/2016 |
RP-74 |
RP-162422 |
0024 |
1 |
F |
AAS ACLR absolute limit |
13.3.0 |
|
12/2016 |
RP-74 |
RP-162422 |
0026 |
– |
F |
Clarification on the Rx diversity branches vs. demodulation branches terminology |
13.3.0 |
|
03/2017 |
RP-75 |
RP-170586 |
0027 |
– |
F |
Corrections of the power range for SEM and OBUE requirement. |
13.4.0 |
|
03/2017 |
RP-75 |
RP-170586 |
0028 |
1 |
F |
TS 37.105: Alignment with legacy specifications on bands 45, 65, 66, 67, 68. |
13.4.0 |
|
03/2017 |
RP-75 |
RP-170586 |
0029 |
1 |
F |
TS 37.105: Corrections on references |
13.4.0 |
|
03/2017 |
RP-75 |
RP-170586 |
0030 |
– |
B |
CR to TS 37.105: Isolation of the NB-IoT feature from the AAS BS specification |
13.4.0 |
|
03/2017 |
RP-75 |
RP-170586 |
0031 |
1 |
B |
CR to TS 37.105: Isolation of Band 46 from the AAS BS specification |
13.4.0 |
|
03/2017 |
RP-75 |
RP-170586 |
0032 |
1 |
D |
CR to TS 37.105: editorial corrections |
13.4.0 |
|
03/2017 |
RP-75 |
RP-170586 |
0033 |
– |
F |
CR to TS 37.105: Rel-13 single RAT and MSR specification reference updates: MB MSR correction |
13.4.0 |
|
03/2017 |
RP-75 |
– |
– |
– |
– |
Update to Rel-14 version (MCC) |
14.0.0 |
|
06/2017 |
RP-76 |
RP-171305 |
0060 |
1 |
A |
CR to TS 37.105: Correction of the spurious emissions requirement |
14.1.0 |
|
06/2017 |
RP-76 |
RP-171305 |
0061 |
A |
CR to TS 37.105: BS demodulation requirements update |
14.1.0 |
|
|
06/2017 |
RP-76 |
RP-171305 |
0062 |
A |
CR to TS 37.105: Addition of 1.4 and 3 MHz channel bandwidths for Band 65 |
14.1.0 |
|
|
09/2017 |
RP-77 |
RP-171968 |
0064 |
A |
CR to TS 37.105: Corrections of the UTRA Inner loop power control and the frequency error requirements; Rel-14 |
14.2.0 |
|
|
09/2017 |
RP-77 |
RP-171968 |
0065 |
1 |
B |
CR to TS 37.105: introduction of bands 48, 69, 70 |
14.2.0 |
|
09/2017 |
RP-77 |
RP-171968 |
0067 |
A |
Transmit pulse shape filter for TDD operation |
14.2.0 |
|
|
09/2017 |
RP-77 |
RP-171968 |
0068 |
F |
CR to TS 37.105: versioned reference updates to Rel-14 non-AAS specifications |
14.2.0 |
|
|
09/2017 |
RP-77 |
RP-171968 |
0070 |
A |
CR to 37.105 on PS-LTE BS regional requirements for Band 28 in Korea |
14.2.0 |
|
|
2017-12 |
RAN#78 |
RP-172599 |
0073 |
B |
CR to TS 37.105: AAS RF specification, v15.0.0 |
15.0.0 |
|
|
2018-03 |
RAN#79 |
RP-180282 |
0074 |
1 |
F |
CR to TS 37.105 |
15.1.0 |
|
2018-06 |
RAN#80 |
RP-181109 |
0077 |
A |
CR to TS 37.105: absolute ACLR limit |
15.2.0 |
|
|
2018-06 |
RAN#80 |
RP-181109 |
0081 |
A |
CR to TS 37.105: Correction of regional requirements – removal of co-location and co-existance (4.5), Rel-15 This CR was not implemented as the changes are not based on the latest version |
15.2.0 |
|
|
2018-06 |
RAN#80 |
RP-181109 |
0086 |
A |
CR to TR 37.105: Clarifications on OTA sensitivity requirement (10.2.1) |
15.2.0 |
|
|
2018-06 |
RAN#80 |
RP-181075 |
0090 |
B |
Introduction of NR to eAAS |
15.2.0 |
|
|
2018-09 |
RAN#81 |
RP-181896 |
0095 |
1 |
F |
Correction on unwanted emission mask for TS 37.105 |
15.3.0 |
|
2018-09 |
RAN#81 |
RP-181917 |
0096 |
F |
CR to TS 37.105: corrections of the regional requirements (4.5) |
15.3.0 |
|
|
2018-09 |
RAN#81 |
RP-181917 |
0097 |
F |
CR to TS 37.105: Correction of the OTA blocking requirement (10.6.2.1) |
15.3.0 |
|
|
2018-12 |
RAN#82 |
RP-182360 |
0099 |
2 |
F |
Corrections to AAS receiver requirements for NR |
15.4.0 |
|
2018-12 |
RAN#82 |
RP-182360 |
0100 |
2 |
F |
Addition of NR to of OTA out of band blocking requirements |
15.4.0 |
|
2018-12 |
RAN#82 |
RP-182360 |
0101 |
2 |
F |
Addition of NR to co-existence and co-location related emissions for single RAT BS |
15.4.0 |
|
2018-12 |
RAN#82 |
RP-182360 |
0102 |
1 |
F |
Correction of NR related OBUE emissions tables |
15.4.0 |
|
2018-12 |
RAN#82 |
RP-182380 |
0108 |
A |
CR to TS 37.105: TS37.145 reference correction, Rel-15 |
15.4.0 |
|
|
2018-12 |
RAN#82 |
RP-182386 |
0109 |
F |
CR to TS 37.105: correction of the "EIRP accuracy directions set" into "OTA peak directions set" |
15.4.0 |
|
|
2018-12 |
RAN#82 |
RP-182386 |
0110 |
1 |
F |
CR to 37.105: Corrections to co-location requirements |
15.4.0 |
|
2018-12 |
RAN#82 |
RP-182387 |
0112 |
F |
CR to TS 37.105: Text alignment for the OTA demodulation branches |
15.4.0 |
|
|
2018-12 |
RAN#82 |
RP-182360 |
0113 |
1 |
F |
Correction of narrowband blocking requirement for NR |
15.4.0 |
|
2018-12 |
RAN#82 |
RP-182380 |
0116 |
A |
Cleanup to conducted requirements text |
15.4.0 |
|
|
2018-12 |
RAN#82 |
RP-182386 |
0117 |
1 |
F |
Cleanup to OTA requirements text |
15.4.0 |
|
2018-12 |
RAN#82 |
RP-182387 |
0118 |
2 |
F |
CR to TS 37.105 – polarisation wording improvements for OTA s reference sensitivity |
15.4.0 |
|
2018-12 |
RAN#82 |
RP-182386 |
0120 |
F |
CR for TS37.105: Clean up multi-band RIBs |
15.4.0 |
|
|
2018-12 |
RAN#82 |
RP-182387 |
0121 |
F |
CR to TS 37.105 Removal of referencing error for in-band blocking |
15.4.0 |
|
|
2019-03 |
RAN#83 |
RP-190418 |
0123 |
3 |
F |
Correction to definition of OTA reference sensitivity |
15.5.0 |
|
2019-03 |
RAN#83 |
RP-190418 |
0124 |
1 |
F |
Correction to TDD OFF power requirement |
15.5.0 |
|
2019-03 |
RAN#83 |
RP-190412 |
0129 |
1 |
F |
CR to TS 37.105 on Correction of unwanted emissions scaling |
15.5.0 |
|
2019-03 |
RAN#83 |
RP-190418 |
0130 |
F |
CR to TS 37.105: Implementation of 1024QAM for E-UTRA, Rel-15 |
15.5.0 |
|
|
2019-03 |
RAN#83 |
RP-190418 |
0131 |
1 |
F |
CR to TS 37.105: Implementation of sTTI for E-UTRA, Rel-15 |
15.5.0 |
|
2019-03 |
RAN#83 |
RP-190418 |
0132 |
2 |
F |
CR to TS 37.105: new Rel-15 bands and isolation of band 49, Tx, Rel-15 |
15.5.0 |
|
2019-03 |
RAN#83 |
RP-190418 |
0133 |
1 |
F |
CR to TS 37.105: new Rel-15 bands and isolation of band 49, Rx, Rel-15 |
15.5.0 |
|
2019-03 |
RAN#83 |
RP-190418 |
0135 |
1 |
F |
CR to TS37.105 Correction to OTA test requirements |
15.5.0 |
|
2019-06 |
RAN#84 |
RP-191262 |
0136 |
1 |
F |
CR to TS 37.105: Corrections on out-of-band blocking requirement |
15.6.0 |
|
2019-06 |
RAN#84 |
RP-191262 |
0137 |
F |
CR to TS 37.105: addition of Band 35, 36, 37 to Tx spurious colocation requirement |
15.6.0 |
|
|
2019-06 |
RAN#84 |
RP-191262 |
0138 |
F |
Corrections to operation in Band 46 and 49 |
15.6.0 |
|
|
2019-06 |
RAN#84 |
RP-191262 |
0140 |
F |
Correction on ΔfOOB for 37.105 |
15.6.0 |
|
|
2019-06 |
RAN#84 |
RP-191262 |
0141 |
1 |
F |
Blocking requirement for MSR/NR operation |
15.6.0 |
|
2019-06 |
RAN#84 |
RP-191262 |
0142 |
F |
Correction to OTA Narrowband blocking requirement |
15.6.0 |
|
|
2019-06 |
RAN#84 |
RP-191262 |
0143 |
1 |
F |
Correction to out of band blocking requirement |
15.6.0 |
|
2019-06 |
RAN#84 |
RP-191262 |
0146 |
F |
Non-AAS CRs mirroring to the AAS specification |
15.6.0 |
|
|
2019-06 |
RAN#84 |
RP-191236 |
0152 |
1 |
F |
CR for TS37.105: correction on TX Diversity and CRS for NR for TAE requirement |
15.6.0 |
|
2019-06 |
RAN#84 |
RP-191250 |
0144 |
1 |
B |
n65 introduction to 37.105 |
16.0.0 |
|
2019-06 |
RAN#84 |
RP-191257 |
0147 |
B |
CR to 37.105: Introduction of Band 87 and 88 |
16.0.0 |
|
|
2019-06 |
RAN#84 |
RP-191249 |
0148 |
B |
CR to 37.105: Introduction of n48 |
16.0.0 |
|
|
2019-06 |
RAN#84 |
RP-191245 |
0149 |
B |
Introduce Band n18 to 37.105 |
16.0.0 |
|
|
2019-06 |
RAN#84 |
RP-191243 |
0150 |
B |
Introduction of Band n14 in TS 37.105 |
16.0.0 |
|
|
2019-06 |
RAN#84 |
RP-191247 |
0151 |
B |
Introduction of Band n30 in TS 37.105 |
16.0.0 |
|
|
2019-09 |
RAN#85 |
RP-192053 |
0154 |
A |
Correction to RX spurious emissions applicability range for SR E-UTRA BS |
16.1.0 |
|
|
2019-09 |
RAN#85 |
RP-192053 |
0156 |
A |
CR for TS37.105: definition of synchronization operation |
16.1.0 |
|
|
2019-09 |
RAN#85 |
RP-192053 |
0158 |
A |
CR to TS 37.105: Clarification on application of OTA receiver requirements for BS supporting polarization |
16.1.0 |
|
|
2019-09 |
RAN#85 |
RP-192046 |
0162 |
A |
CR to TS 37.105: Correction on operation band unwanted emission |
16.1.0 |
|
|
2019-09 |
RAN#85 |
RP-192046 |
0164 |
A |
CR to TS37.105 Corrections on NBB requirement (section 7.4 and 10.5) |
16.1.0 |
|
|
2019-09 |
RAN#85 |
RP-192030 |
0165 |
F |
CR on Protection of SUL band n89 to TS 37.105 |
16.1.0 |
|
|
2019-09 |
RAN#85 |
RP-192034 |
0166 |
B |
n29 introduction to 37.105 |
16.1.0 |
|
|
2019-09 |
RAN#85 |
RP-192050 |
0170 |
A |
CR to 37.105: correction of TAB connectors mapping to TAB connector TX min cell group, Rel-16 |
16.1.0 |
|
|
2019-12 |
RAN#86 |
RP-193014 |
0171 |
B |
Introduction of 2010-2025MHz SUL band into Rel-16 TS 37.105 |
16.2.0 |
|
|
2019-12 |
RAN#86 |
RP-193037 |
0173 |
A |
CR to 37.105 on Receiver spurious emission requirements |
16.2.0 |
|
|
2019-12 |
RAN#86 |
RP-193037 |
0175 |
1 |
A |
CR to 37.105 on Reciever Intermodulation signal offset correction |
16.2.0 |
|
2019-12 |
RAN#86 |
RP-193037 |
0177 |
A |
CR to TS37.105 Corrections on NBB requirement (section 7.4 and 10.5) |
16.2.0 |
|
|
2019-12 |
RAN#86 |
RP-193048 |
0179 |
A |
CR to TS 37.105: Requirement set applicability |
16.2.0 |
|
|
2019-12 |
RAN#86 |
RP-192844 |
0180 |
B |
CR to 37.105 on variable duplex FDD bands |
16.2.0 |
|
|
2020-03 |
RAN#87 |
RP-200381 |
0181 |
B |
Introduction of n26 |
16.3.0 |
|
|
2020-03 |
RAN#87 |
RP-200382 |
0182 |
B |
Introduction of n53 |
16.3.0 |
|
|
2020-06 |
RAN#88 |
RP-200984 |
0184 |
F |
CR to TS 37.105: removal of [], Rel-16 |
16.4.0 |
|
|
2020-09 |
RAN#89 |
RP-201512 |
0191 |
|
A |
CR to TS 37.105: Rel-13 non-AAS CRs mirroring, Rel-16 |
16.5.0 |
|
2020-09 |
RAN#89 |
RP-201512 |
0194 |
|
A |
CR to TS 37.105: Rel-14 non-AAS CRs mirroring, Rel-16 |
16.5.0 |
|
2020-09 |
RAN#89 |
RP-201512 |
0196 |
|
A |
CR to TS 37.105: Rel-15 non-AAS CRs mirroring, Rel-16 |
16.5.0 |
|
2020-09 |
RAN#89 |
RP-201512 |
0197 |
|
F |
CR to TS 37.105: Rel-15 non-AAS CRs mirroring, Rel-15 |
16.5.0 |
|
2020-09 |
RAN#89 |
RP-201512 |
0199 |
|
B |
CR to 37.105: Introduction of NR-U co-existence requirements |
16.5.0 |
|
2020-12 |
RAN#90 |
RP-202510 |
0206 |
|
A |
CR to TS 37.105: Corrections to core requirements including UEM additional requirements, Rel-16 |
16.6.0 |
|
2020-12 |
RAN#90 |
RP-202414 |
0207 |
|
B |
CR to 37.105: Introduction of n96 medium range requirements |
16.6.0 |
|
2020-12 |
RAN#90 |
RP-202510 |
0209 |
|
A |
CR to 37.105 on Removal of additional limit for Band 1 |
16.6.0 |
|
2020-12 |
RAN#90 |
RP-202510 |
0213 |
|
A |
CR to TS 37.105: addition of the OBUE applicability table, Rel-16 |
16.6.0 |
|
2020-12 |
RAN#90 |
RP-202451 |
0200 |
|
B |
Introduction of 1880-1920MHz SUL band into Rel-17 TS 37.105 |
17.0.0 |
|
2020-12 |
RAN#90 |
RP-202452 |
0201 |
|
B |
Introduction of 2300-2400MHz SUL band into Rel-17 TS 37.105 |
17.0.0 |
|
2020-12 |
RAN#90 |
RP-202448 |
0203 |
|
B |
CR to TS 37.105: introduction of NR band n13 |
17.0.0 |
|
2021-03 |
RAN#91e |
RP-210097 |
0214 |
|
B |
CR for 37.105 Introduction of NR band n24 |
17.1.0 |
|
2021-03 |
RAN#91e |
RP-210096 |
0216 |
|
B |
CR for TS 37.105 Introduction of SUL for UL of NR band n24 |
17.1.0 |
|
2021-03 |
RAN#91 |
RP-210110 |
0218 |
A |
CR for 37.105: Corrections related to Band 24 regulatory updates |
17.1.0 |
|
|
2021-03 |
RAN#91e |
RP-210118 |
0223 |
|
A |
CR to TS 37.105: Introduction of new BS capability set for NR+EUTRA+UTRA, Rel-17 |
17.1.0 |
|
2021-06 |
RAN#92 |
RP-211076 |
0232 |
A |
CR to TS 37.105: Regional requirements for band 41 in Japan, Rel-17 |
17.2.0 |
|
|
2021-06 |
RAN#92 |
RP-211116 |
0233 |
B |
CR to TS 37.105: Introduction of band n67 |
17.2.0 |
|
|
2021-06 |
RAN#92 |
RP-211116 |
0234 |
1 |
B |
CR to TS 37.105: Introduction of band n85 |
17.2.0 |
|
2021-06 |
RAN#92 |
RP-211090 |
0238 |
A |
CR to 37.105: In-band blocking for multi-band Base Stations |
17.2.0 |
|
|
2021-09 |
RAN#93 |
RP-211909 |
0239 |
B |
CR to TS 37.105: Introduction of 35 MHz and 45 MHz |
17.3.0 |
|
|
2021-09 |
RAN#93 |
RP-211925 |
0242 |
A |
Big CR for TS 37.105 Maintenance (Rel-17, CAT A) |
17.3.0 |
|
|
2021-12 |
RAN#94 |
RP-212853 |
0246 |
A |
Big CR for TS 37.105 Maintenance (Rel-17, CAT A) |
17.4.0 |
|
|
2022-03 |
RAN#95 |
RP-220357 |
0249 |
B |
CR for 37.105 on Introduction of lower 6GHz NR unlicensed operation for Europe |
17.5.0 |
|
|
2022-03 |
RAN#95 |
RP-220347 |
0248 |
1 |
B |
CR to TS37.105 on introduction of upper 700MHz A block |
17.5.0 |
|
2022-03 |
RAN#95 |
RP-220331 |
0252 |
A |
Big CR for TS 37.105 Maintenance (Rel-17, CAT A) |
17.5.0 |
|
|
2022-03 |
RAN#95 |
RP-220376 |
0253 |
B |
CR to TS 37.105: RMR 1900MHz band n101 introduction |
17.5.0 |
|
|
2022-06 |
RAN#96 |
RP-221684 |
0255 |
B |
CR to TS 37.105: introduction of n100 co-existence requirements, Rel-17 |
17.6.0 |
|
|
2022-06 |
RAN#96 |
RP-221673 |
0254 |
1 |
B |
Introducing 6GHz licensed operation into 37.105 |
17.6.0 |
|
2022-06 |
RAN#96 |
RP-221652 |
0258 |
A |
Big CR for TS 37.105 Maintenance (Rel-17, CAT A) |
17.6.0 |
|