A.4.5 Feature group indicators

36.523-23GPPEvolved Universal Terrestrial Radio Access (E-UTRA) and Evolved Packet Core (EPC)Part 2: Implementation conformance statement (ICS) proforma specificationRelease 17TSUser Equipment (UE) conformance specification

For the purpose of conformance testing, the definition of each Feature Group Indicator (FGI) is duplicated from Rel-8 for each possible E-UTRA mode, i.e. FDD (Tables A.4.5-1a, A.4.5-1d and A.4.5-3a) and TDD (Tables A.4.5-1b, A.4.5-1e and A.4.5-3b). For each FGI (applicable to the Release supported by the UE):

– If the UE supports E-UTRA FDD and TDD: both FDD and TDD support statuses shall be declared separately (see Note 2).

– If the UE supports single E-UTRA xDD mode: only the xDD-specific support status needs to be declared.

Note 1: From Rel-11 onwards 3GPP TSG RAN has discontinued the usage of FGI bits. Instead it has introduced a different mechanism to accomplish the same purposes based on the principles described in TS 36.306 [13] clause 4. These new principles where applicable should be catered for elsewhere in the present document e.g. in section A.4.4.

Note 2: For Rel-8 UE, the separate declaration also applies to FGI 1-32.

Note 3: ‘VoLTE’ in the tables A.4.5-1a and A.4.5-1b corresponds to a UE which is IMS voice capable.

Table A.4.5-1: Void

Table A.4.5-1a: Feature group indicators 1-32 for FDD

Item

Additional information

Notes

If indicated "Yes" the feature shall be implemented and successfully tested for the corresponding release

Release

Ref.

Mnemonic

Comments

1

Support of

– Intra-subframe frequency hopping for PUSCH scheduled by UL grant

– DCI format 3a (TPC commands for PUCCH and PUSCH with single bit power adjustments)

– Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-0 – UE selected subband CQI without PMI

– Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI

– set to 1 by category M1 and M2 UEs that have implemented and successfully tested “ZAperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-0 – UE selected subband CQI without PM"

Rel-8

36.331, Annex B.1

pc_FeatrGrp_1_F

Corresponding to the Index of Indicator, the leftmost binary bit 1.
Set to true if supporting all functionalities in the feature group.

2

Support of

– Simultaneous CQI and ACK/NACK on PUCCH, i.e. PUCCH format 2a and 2b

– Absolute TPC command for PUSCH

– Resource allocation type 1 for PDSCH

– Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-0 – UE selected subband CQI without PMI

– Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_2_F

Corresponding to the Index of Indicator, the leftmost binary bit 2.
Set to true if supporting all functionalities in the feature group.

3

Support of

– Semi-persistent scheduling

– TTI bundling

– 5bit RLC UM SN

– 7bit PDCP SN

– can only be set to 1 if the UE has set bit number 7 to 1.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_3_F

Corresponding to the Index of Indicator, the leftmost binary bit 3.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 3 in Table A.4.5-1b for TDD.

Support of

– 5bit RLC UM SN

– 7bit PDCP SN

– can only be set to 1 if the UE has set bit number 7 to 1.

Yes, if UE supports VoLTE

Rel-9, Rel-10

Yes, if UE supports VoLTE.

Yes, if UE supports SRVCC to EUTRAN from GERAN.

Rel-11

4

Support of

– Short DRX cycle

– can only be set to 1 if the UE has set bit number 5 to 1.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_4_F

Corresponding to the Index of Indicator, the leftmost binary bit 4.
Set to true if supporting all functionalities in the feature group.

5

Support of

– Long DRX cycle

– DRX command MAC control element

Rel-8

36.331, Annex B.1

pc_FeatrGrp_5_F

Corresponding to the Index of Indicator, the leftmost binary bit 5.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 5 in Table A.4.5-1b for TDD.

Yes

Rel-9

6

Support of

– Prioritized bit rate

Rel-8

36.331, Annex B.1

pc_FeatrGrp_6_F

Corresponding to the Index of Indicator, the leftmost binary bit 6.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 6 in Table A.4.5-1b for TDD.

Yes

Rel-9

7

Support of

– RLC UM

– can only be set to 0 if the UE does not support voice

Rel-8

36.331, Annex B.1

pc_FeatrGrp_7_F

Corresponding to the Index of Indicator, the leftmost binary bit 7.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 7 in Table A.4.5-1b for TDD.

Yes, if UE supports VoLTE

Rel-9, Rel-10

Yes, if UE supports VoLTE.

Yes, if UE supports SRVCC to EUTRAN from GERAN.

Rel-11

8

Support of

– EUTRA RRC_CONNECTED to UTRA CELL_DCH PS handover

– can only be set to 1 if the UE has set bit number 22 to 1

Rel-8

36.331, Annex B.1

pc_FeatrGrp_8_F

Corresponding to the Index of Indicator, the leftmost binary bit 8.
Set to true if supporting all functionalities in the feature group.

Support of

– EUTRA RRC_CONNECTED to UTRA FDD or UTRA TDD CELL_DCH PS handover, if the UE supports either only UTRAN FDD or only UTRAN TDD

– EUTRA RRC_CONNECTED to UTRA FDD CELL_DCH PS handover, if the UE supports both UTRAN FDD and UTRAN TDD

Yes (except for category M1 amd M2 UEs), if UE supports UTRA FDD

Rel-9

9

Support of

– EUTRA RRC_CONNECTED to GERAN GSM_Dedicated handover

– related to SR-VCC

– can only be set to 1 if the UE has set bit number 23 to 1

Rel-8 to Rel-10

36.331, Annex B.1

pc_FeatrGrp_9_F

Corresponding to the Index of Indicator, the leftmost binary bit 9.
Set to true if supporting all functionalities in the feature group.

Yes (except for category M1 and M2 UEs), if UE supports SRVCC to EUTRAN from GERAN.

Rel-11

10

Support of

– EUTRA RRC_CONNECTED to GERAN (Packet_)Idle by Cell Change Order

– EUTRA RRC_CONNECTED to GERAN (Packet_)Idle by Cell Change Order with NACC (Network Assisted Cell Change)

Rel-8

36.331, Annex B.1

pc_FeatrGrp_10_F

Corresponding to the Index of Indicator, the leftmost binary bit 10.
Set to true if supporting all functionalities in the feature group.

11

Support of

– EUTRA RRC_CONNECTED to CDMA2000 1xRTT CS Active handover

– can only be set to 1 if the UE has sets bit number 24 to 1

Rel-8

36.331, Annex B.1

pc_FeatrGrp_11_F

Corresponding to the Index of Indicator, the leftmost binary bit 11.Set to true if supporting all functionalities in the feature group.

12

Support of

– EUTRA RRC_CONNECTED to CDMA2000 HRPD Active handover

– can only be set to 1 if the UE has set bit number 26 to 1

Rel-8

36.331, Annex B.1

pc_FeatrGrp_12_F

Corresponding to the Index of Indicator, the leftmost binary bit 12.
Set to true if supporting all functionalities in the feature group.

13

Support of

– Inter-frequency handover (within FDD or TDD)

– can only be set to 1 if the UE has set bit number 25 to 1

Rel-8

36.331, Annex B.1

pc_FeatrGrp_13_F

Corresponding to the Index of Indicator, the leftmost binary bit 13.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 13 in Table A.4.5-1b for TDD.

Yes (except for category M1 and M2 UEs), unless UE only supports band 13

Rel-9

14

Support of

– Measurement reporting event: Event A4 – Neighbour > threshold

– Measurement reporting event: Event A5 – Serving < threshold1 & Neighbour > threshold2

Rel-8

36.331, Annex B.1

pc_FeatrGrp_14_F

Corresponding to the Index of Indicator, the leftmost binary bit 14.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 14 in Table A.4.5-1b for TDD.

Yes (except for category M1 and M2 UEs)

Rel-9

15

Support of

– Measurement reporting event: Event B1 – Neighbour > threshold for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1

– Measurement reporting event: Event B1 – Neighbour > threshold for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively

– Measurement reporting event: Event B1 – Neighbour > threshold for GERAN, 1xRTT or HRPD, if the UE has set bit number 23, 24 or 26 to 1, respectively

– can only be set to 1 if the UE has set at least one of the bit number 22, 23, 24, 26 or 39 to 1.

– even if the UE sets bits 41, it shall still set bit 15 to 1 if measurement reporting event B1 is tested for all RATs supported by UE

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_15_F

Corresponding to the Index of Indicator, the leftmost binary bit 15.
Set to true if supporting all functionalities in the feature group.

Yes for FDD, if UE supports only UTRAN FDD and does not support UTRAN TDD or GERAN or 1xRTT or HRPD

Rel-9

16

Support of

– Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells;

– Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells, if the UE has set bit number 25 to 1; and

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN, GERAN, 1xRTT or HRPD, if the UE has set bit number 22, 23, 24 or 26 to 1, respectively

NOTE: Event triggered periodical reporting (i.e. with triggerType set to event and with reportAmount > 1) is a mandatory functionality of event triggered reporting and therefore not the subject of this bit.

Support of

– Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells

– Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells, if the UE has set bit number 25 to 1

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, 1xRTT or HRPD, if the UE has set bit number 23, 24 or 26 to 1, respectively

NOTE: Event triggered periodical reporting (i.e., with triggerType set to event and with reportAmount > 1) is a mandatory functionality of event triggered reporting and therefore not the subject of this bit.

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_16_F

Corresponding to the Index of Indicator, the leftmost binary bit 16.Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 16 in Table A.4.5-1b for TDD.

Yes

Rel-9

17

Support of

Intra-frequency ANR features including:

– Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells

– Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI

– can only be set to 1 if the UE has set bit number 5 to 1.

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_17_F

Corresponding to the Index of Indicator, the leftmost binary bit 17.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 17 in Table A.4.5-1b for TDD.

Yes

Rel-9

18

Support of

Inter-frequency ANR features including:

– Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells

– Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI

– can only be set to 1 if the UE has set bit number 5 to 1.

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_18_F

Corresponding to the Index of Indicator, the leftmost binary bit 18.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 18 in Table A.4.5-1b for TDD.

Yes, unless UE only supports band 13

Rel-9

19

Support of

Inter-RAT ANR features including:

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, if the UE has set bit number 23 to 1

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN, 1xRTT or HRPD, if the UE has set bit number 22, 24 or 26 to 1, respectively

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for UTRAN, GERAN, 1xRTT or HRPD, if the UE has set bit number 22, 23, 24 or 26 to 1, respectively

– can only be set to 1 if the UE has set bit number 5 to 1 and the UE has set at least one of the bit number 22, 23, 24 or 26 to 1.

– even if the UE sets bits 33 to 36, it shall still set bit 19 to 1 if inter-RAT ANR features are tested for all RATs for which inter-RAT measurement reporting is indicated as tested

Rel-8

36.331, Annex B.1

pc_FeatrGrp_19_F

Corresponding to the Index of Indicator, the leftmost binary bit 19.
Set to true if supporting all functionalities in the feature group.

Support of

Inter-RAT ANR features including:

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, if the UE has set bit number 23 to 1

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for 1xRTT or HRPD, if the UE has set bit number 24 or 26 to 1, respectively

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRANTDD and has set bit number 22 to 1

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for GERAN, 1xRTT or HRPD, if the UE has set bit number 23, 24 or 26 to 1, respectively

Rel-9

20

If bit number 7 is set to ‘0’:

– SRB1 and SRB2 for DCCH + 8x AM DRB

If bit number 7 is set to ‘1’:

– SRB1 and SRB2 for DCCH + 8x AM DRB

– SRB1 and SRB2 for DCCH + 5x AM DRB + 3x UM DRB

NOTE: UE which indicate support for a DRB combination also support all subsets of the DRB combination. Therefore, release of DRB(s) never results in an unsupported DRB combination.

– Regardless of what bit number 7 and bit number 20 is set to, UE shall support at least SRB1 and SRB2 for DCCH + 4x AM DRB

– Regardless of what bit number 20 is set to, if bit number 7 is set to ‘1’, UE shall support at least SRB1 and SRB2 for DCCH + 4x AM DRB + 1x UM DRB

Rel-8

36.331, Annex B.1

pc_FeatrGrp_20_F

Corresponding to the Index of Indicator, the leftmost binary bit 20.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 20 in Table A.4.5-1b for TDD.

Yes

Rel-9

21

Support of

– Predefined intra- and inter-subframe frequency hopping for PUSCH with N_sb > 1

– Predefined inter-subframe frequency hopping for PUSCH with N_sb > 1

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_21_F

Corresponding to the Index of Indicator, the leftmost binary bit 21.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 21 in Table A.4.5-1b for TDD.

22

Support of

– UTRAN measurements, reporting and measurement reporting event B2 in E-UTRA connected mode

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_22_F

Corresponding to the Index of Indicator, the leftmost binary bit 22.
Set to true if supporting all functionalities in the feature group.

Support of

– UTRAN FDD or UTRAN TDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports either only UTRAN FDD or only UTRAN TDD

– UTRAN FDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports both UTRAN FDD and UTRAN TDD

Yes, if UE supports UTRA

Rel-9

23

Support of

– GERAN measurements, reporting and measurement reporting event B2 in E-UTRA connected mode

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_23_F

Corresponding to the Index of Indicator, the leftmost binary bit 23.Set to true if supporting all functionalities in the feature group.

24

Support of

– 1xRTT measurements, reporting and measurement reporting event B2 in E-UTRA connected mode

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_24_F

Corresponding to the Index of Indicator, the leftmost binary bit 24.

Set to true if supporting all functionalities in the feature group.

Yes, if UE supports enhanced 1xRTT CSFB

Rel-9

25

Support of

– Inter-frequency measurements and reporting in E-UTRA connected mode

NOTE: The UE setting this bit to 1 and indicating support for FDD and TDD frequency bands in the UE capability signalling implements and is tested for FDD measurements while the UE is in TDD, and for TDD measurements while the UE is in FDD.

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_25_F

Corresponding to the Index of Indicator, the leftmost binary bit 25.

Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 25 in Table A.4.5-1b for TDD.

Yes, unless UE only supports band 13

Rel-9

26

Support of

– HRPD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_26_F

Corresponding to the Index of Indicator, the leftmost binary bit 26.
Set to true if supporting all functionalities in the feature group.

Yes, if UE supports HRPD

Rel-9

27

Support of

– EUTRA RRC_CONNECTED to UTRA CELL_DCH CS handover

– related to SR-VCC

– can only be set to 1 if the UE has set bit number 8 to 1 and supports SR-VCC from EUTRA defined in TS 24.008.

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_27_F

Corresponding to the Index of Indicator, the leftmost binary bit 27.

Set to true if supporting all functionalities in the feature group.

Support of

– EUTRA RRC_CONNECTED to UTRA FDD or UTRA TDD CELL_DCH CS handover, if the UE supports either only UTRAN FDD or only UTRAN TDD

– EUTRA RRC_CONNECTED to UTRA FDD CELL_DCH CS handover, if the UE supports both UTRAN FDD and UTRAN TDD

Yes, if UE supports VoLTE and UTRA FDD

Rel-9

28

Support of

– TTI bundling

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Yes

Rel-9

36.331, Annex B.1

pc_FeatrGrp_28_F

Corresponding to the Index of Indicator, the leftmost binary bit 28.Set to true if supporting all functionalities in the feature group.

29

Support of

– Semi-Persistent Scheduling

– If a category M1 UE does not support this feature group, this bit shall be set to 0.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_29_F

Corresponding to the Index of Indicator, the leftmost binary bit 29.Set to true if supporting all functionalities in the feature group.

30

Support of

– Handover between FDD and TDD

– can only be set to 1 if the UE has set bit number 13 to 1

Rel-8

36.331, Annex B.1

pc_FeatrGrp_30_F

Corresponding to the Index of Indicator, the leftmost binary bit 30.

Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 30 in Table A.4.5-1b for TDD.

31

Support of

– Indicates whether the UE supports the mechanisms defined for cells broadcasting multi band information i.e. comprehending multiBandInfoList, disregarding in RRC_CONNECTED the related system information fields and understanding the EARFCN signalling for all bands, that overlap with the bands supported by the UE, and that are defined in the earliest version of TS 36.101 [42] that includes all UE supported bands.

– This FGI bit is concerns an optional release independent feature (as it was difficult to introduce this from REL-8 when using regular UE capability signalling)

Rel-8

36.331, Annex B.1

pc_FeatrGrp_31_F

Corresponding to the Index of Indicator, the leftmost binary bit 31.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 31 in Table A.4.5-1b for TDD.

Yes

Rel-10

32

Undefined

Rel-8

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 32.

Table A.4.5-1b: Feature group indicators 1-32 for TDD

Item

Additional information

Notes

If indicated "Yes" the feature shall be implemented and successfully tested for the corresponding release

Release

Ref.

Mnemonic

Comments

1

Support of

– Intra-subframe frequency hopping for PUSCH scheduled by UL grant

– DCI format 3a (TPC commands for PUCCH and PUSCH with single bit power adjustments)

– Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-0 – UE selected subband CQI without PMI

– Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI

– set to 1 by category M1 and M2 UEs that have implemented and successfully tested "Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-0 – UE selected subband CQI without PM"

Rel-8

36.331, Annex B.1

pc_FeatrGrp_1_T

Corresponding to the Index of Indicator, the leftmost binary bit 1.
Set to true if supporting all functionalities in the feature group.

2

Support of

– Simultaneous CQI and ACK/NACK on PUCCH, i.e. PUCCH format 2a and 2b

– Absolute TPC command for PUSCH

– Resource allocation type 1 for PDSCH

– Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-0 – UE selected subband CQI without PMI

– Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_2_T

Corresponding to the Index of Indicator, the leftmost binary bit 2.
Set to true if supporting all functionalities in the feature group.

3

Support of

– Semi-persistent scheduling

– TTI bundling

– 5bit RLC UM SN

– 7bit PDCP SN

– can only be set to 1 if the UE has set bit number 7 to 1.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_3_T

Corresponding to the Index of Indicator, the leftmost binary bit 3.

Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 3 in Table A.4.5-1a for FDD.

Yes, if UE supports VoLTE

Rel-9, Rel-10

Support of

– 5bit RLC UM SN

– 7bit PDCP SN

Yes, if UE supports VoLTE.

Yes, if UE supports SRVCC to EUTRAN from GERAN.

Rel-11

4

Support of

– Short DRX cycle

– can only be set to 1 if the UE has set bit number 5 to 1.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_4_T

Corresponding to the Index of Indicator, the leftmost binary bit 4.

Set to true if supporting all functionalities in the feature group.

5

Support of

– Long DRX cycle

– DRX command MAC control element

Rel-8

36.331, Annex B.1

pc_FeatrGrp_5_T

Corresponding to the Index of Indicator, the leftmost binary bit 5.

Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 5 in Table A.4.5-1a for FDD.

Yes

Rel-9

6

Support of

– Prioritized bit rate

Rel-8

36.331, Annex B.1

pc_FeatrGrp_6_T

Corresponding to the Index of Indicator, the leftmost binary bit 6.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 6 in Table A.4.5-1a for FDD.

Yes

Rel-9

7

Support of

– RLC UM

– can only be set to 0 if the UE does not support voice

Rel-8

36.331, Annex B.1

pc_FeatrGrp_7_T

Corresponding to the Index of Indicator, the leftmost binary bit 7.

Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 7 in Table A.4.5-1a for FDD.

Yes, if UE supports VoLTE

Rel-9, Rel-10

Yes, if UE supports VoLTE.

Yes, if UE supports SRVCC to EUTRAN from GERAN.

Rel-11

8

Support of

– EUTRA RRC_CONNECTED to UTRA FDD or UTRA TDD CELL_DCH PS handover, if the UE supports either only UTRAN FDD or only UTRAN TDD

– EUTRA RRC_CONNECTED to UTRA FDD CELL_DCH PS handover, if the UE supports both UTRAN FDD and UTRAN TDD

– can only be set to 1 if the UE has set bit number 22 to 1

Rel-8

36.331, Annex B.1

pc_FeatrGrp_8_T

Corresponding to the Index of Indicator, the leftmost binary bit 8.
Set to true if supporting all functionalities in the feature group.

9

Support of

– EUTRA RRC_CONNECTED to GERAN GSM_Dedicated handover

– related to SR-VCC

– can only be set to 1 if the UE has set bit number 23 to 1

Rel-8 to Rel-10

36.331, Annex B.1

pc_FeatrGrp_9_T

Corresponding to the Index of Indicator, the leftmost binary bit 9.
Set to true if supporting all functionalities in the feature group.

Yes (except for category M1 and M2 UEs), if UE supports SRVCC to EUTRAN from GERAN.

Rel-11

10

Support of

– EUTRA RRC_CONNECTED to GERAN (Packet_)Idle by Cell Change Order

– EUTRA RRC_CONNECTED to GERAN (Packet_)Idle by Cell Change Order with NACC (Network Assisted Cell Change)

Rel-8

36.331, Annex B.1

pc_FeatrGrp_10_T

Corresponding to the Index of Indicator, the leftmost binary bit 10.
Set to true if supporting all functionalities in the feature group.

11

Support of

– EUTRA RRC_CONNECTED to CDMA2000 1xRTT CS Active handover

– can only be set to 1 if the UE has sets bit number 24 to 1

Rel-8

36.331, Annex B.1

pc_FeatrGrp_11_T

Corresponding to the Index of Indicator, the leftmost binary bit 11.
Set to true if supporting all functionalities in the feature group.

12

Support of

– EUTRA RRC_CONNECTED to CDMA2000 HRPD Active handover

– can only be set to 1 if the UE has set bit number 26 to 1

Rel-8

36.331, Annex B.1

pc_FeatrGrp_12_T

Corresponding to the Index of Indicator, the leftmost binary bit 12.
Set to true if supporting all functionalities in the feature group.

13

Support of

– Inter-frequency handover (within FDD or TDD)

– can only be set to 1 if the UE has set bit number 25 to 1

Rel-8

36.331, Annex B.1

pc_FeatrGrp_13_T

Corresponding to the Index of Indicator, the leftmost binary bit 13.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 13 in Table A.4.5-1a for FDD.

Yes (except for category M1 and M2 UEs),, unless UE only supports band 13

Rel-9

14

Support of

– Measurement reporting event: Event A4 – Neighbour > threshold

– Measurement reporting event: Event A5 – Serving < threshold1 & Neighbour > threshold2

Rel-8

36.331, Annex B.1

pc_FeatrGrp_14_T

Corresponding to the Index of Indicator, the leftmost binary bit 14.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 14 in Table A.4.5-1a for FDD.

Yes (except for category M1 and M2 UEs),

Rel-9

15

Support of

– Measurement reporting event: Event B1 – Neighbour > threshold for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1

– Measurement reporting event: Event B1 – Neighbour > threshold for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively

– Measurement reporting event: Event B1 – Neighbour > threshold for GERAN, 1xRTT or HRPD, if the UE has set bit number 23, 24 or 26 to 1, respectively

– can only be set to 1 if the UE has set at least one of the bit number 22, 23, 24, 26 or 39 to 1.

– even if the UE sets bits 41, it shall still set bit 15 to 1 if measurement reporting event B1 is tested for all RATs supported by UE

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_15_T

Corresponding to the Index of Indicator, the leftmost binary bit 15.
Set to true if supporting all functionalities in the feature group.

16

Support of

– Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells;

– Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells, if the UE has set bit number 25 to 1; and

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN, GERAN, 1xRTT or HRPD, if the UE has set bit number 22, 23, 24 or 26 to 1, respectively

NOTE: Event triggered periodical reporting (i.e. with triggerType set to event and with reportAmount > 1) is a mandatory functionality of event triggered reporting and therefore not the subject of this bit.

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_16_T

Corresponding to the Index of Indicator, the leftmost binary bit 16.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 16 in Table A.4.5-1a for FDD.

Support of

– Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells;

– Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells, if the UE has set bit number 25 to 1

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, 1xRTT or HRPD, if the UE has set bit number 23, 24 or 26 to 1, respectively

NOTE: Event triggered periodical reporting (i.e. with triggerType set to event and with reportAmount > 1) is a mandatory functionality of event triggered reporting and therefore not the subject of this bit.

Yes

Rel-9

17

Support of

Intra-frequency ANR features including:

– Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells

– Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI

– can only be set to 1 if the UE has set bit number 5 to 1.

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_17_T

Corresponding to the Index of Indicator, the leftmost binary bit 17.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 17 in Table A.4.5-1a for FDD.

Yes

Rel-9

18

Support of

Inter-frequency ANR features including:

– Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells

– Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI

– can only be set to 1 if the UE has set bit number 5 to 1.

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_18_T

Corresponding to the Index of Indicator, the leftmost binary bit 18.
Set to true if supporting all functionalities in the feature groupIf UE supports FDD and TDD this item shall be set to same value as for item 18 in Table A.4.5-1a for FDD.

Yes, unless UE only supports band 13

Rel-9

19

Support of

Inter-RAT ANR features including:

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, if the UE has set bit number 23 to 1

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN, 1xRTT or HRPD, if the UE has set bit number 22, 24 or 26 to 1, respectively

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for UTRAN, GERAN, 1xRTT or HRPD, if the UE has set bit number 22, 23, 24 or 26 to 1, respectively

– can only be set to 1 if the UE has set bit number 5 to 1 and the UE has set at least one of the bit number 22, 23, 24 or 26 to 1.

– even if the UE sets bits 33 to 36, it shall still set bit 19 to 1 if inter-RAT ANR features are tested for all RATs for which inter-RAT measurement reporting is indicated as tested

Rel-8

36.331, Annex B.1

pc_FeatrGrp_19_T

Corresponding to the Index of Indicator, the leftmost binary bit 19.Set to true if supporting all functionalities in the feature group.

Support of

Inter-RAT ANR features including:

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, if the UE has set bit number 23 to 1

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for 1xRTT or HRPD, if the UE has set bit number 24 or 26 to 1, respectively.

Rel-9

20

If bit number 7 is set to ‘0’:

– SRB1 and SRB2 for DCCH + 8x AM DRB

If bit number 7 is set to ‘1’:

– SRB1 and SRB2 for DCCH + 8x AM DRB

– SRB1 and SRB2 for DCCH + 5x AM DRB + 3x UM DRB

NOTE: UE which indicate support for a DRB combination also support all subsets of the DRB combination. Therefore, release of DRB(s) never results in an unsupported DRB combination.

– Regardless of what bit number 7 and bit number 20 is set to, UE shall support at least SRB1 and SRB2 for DCCH + 4x AM DRB

– Regardless of what bit number 20 is set to, if bit number 7 is set to ‘1’, UE shall support at least SRB1 and SRB2 for DCCH + 4x AM DRB + 1x UM DRB

Rel-8

36.331, Annex B.1

pc_FeatrGrp_20_T

Corresponding to the Index of Indicator, the leftmost binary bit 20.

Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 20 in Table A.4.5-1a for FDD.

Yes

Rel-9

21

Support of

– Predefined intra- and inter-subframe frequency hopping for PUSCH with N_sb > 1

– Predefined inter-subframe frequency hopping for PUSCH with N_sb > 1

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_21_T

Corresponding to the Index of Indicator, the leftmost binary bit 21.

Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 21 in Table A.4.5-1a for FDD.

22

Support of

– UTRAN measurements, reporting and measurement reporting event B2 in E-UTRA connected mode

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_22_T

Corresponding to the Index of Indicator, the leftmost binary bit 22.

Set to true if supporting all functionalities in the feature group.

Support of

– UTRAN FDD or UTRAN TDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports either only UTRAN FDD or only UTRAN TDD

– UTRAN FDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports both UTRAN FDD and UTRAN TDD

Rel-9

23

Support of

– GERAN measurements, reporting and measurement reporting event B2 in E-UTRA connected mode

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_23_T

Corresponding to the Index of Indicator, the leftmost binary bit 23.

Set to true if supporting all functionalities in the feature group.

24

Support of

– 1xRTT measurements, reporting and measurement reporting event B2 in E-UTRA connected mode

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_24_T

Corresponding to the Index of Indicator, the leftmost binary bit 24.

Set to true if supporting all functionalities in the feature group.

Yes, if UE supports enhanced 1xRTT CSFB

Rel-9

25

Support of

– Inter-frequency measurements and reporting in E-UTRA connected mode

NOTE: The UE setting this bit to 1 and indicating support for FDD and TDD frequency bands in the UE capability signalling implements and is tested for FDD measurements while the UE is in TDD, and for TDD measurements while the UE is in FDD.

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_25_T

Corresponding to the Index of Indicator, the leftmost binary bit 25.

Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 25 in Table A.4.5-1a for FDD.

Yes, unless UE only supports band 13

Rel-9

26

Support of

– HRPD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_26_T

Corresponding to the Index of Indicator, the leftmost binary bit 26.

Set to true if supporting all functionalities in the feature group.

Yes, if UE supports HRPD

Rel-9

27

Support of

– EUTRA RRC_CONNECTED to UTRA CELL_DCH CS handover

– related to SR-VCC

– can only be set to 1 if the UE has set bit number 8 to 1 and supports SR-VCC from EUTRA defined in TS 24.008

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-8

36.331, Annex B.1

pc_FeatrGrp_27_T

Corresponding to the Index of Indicator, the leftmost binary bit 27.

Set to true if supporting all functionalities in the feature group.

Support of

– EUTRA RRC_CONNECTED to UTRA FDD or UTRA TDD CELL_DCH CS handover, if the UE supports either only UTRAN FDD or only UTRAN TDD

– EUTRA RRC_CONNECTED to UTRA FDD CELL_DCH CS handover, if the UE supports both UTRAN FDD and UTRAN TDD

Rel-9

28

Support of

– TTI bundling

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_28_T

Corresponding to the Index of Indicator, the leftmost binary bit 28.
Set to true if supporting all functionalities in the feature group.

29

Support of

– Semi-Persistent Scheduling

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_29_T

Corresponding to the Index of Indicator, the leftmost binary bit 29.
Set to true if supporting all functionalities in the feature group.

30

Support of

– Handover between FDD and TDD

– can only be set to 1 if the UE has set bit number 13 to 1

Rel-8

36.331, Annex B.1

pc_FeatrGrp_30_T

Corresponding to the Index of Indicator, the leftmost binary bit 30.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 30 in Table A.4.5-1a for FDD.

31

Support of

– Indicates whether the UE supports the mechanisms defined for cells broadcasting multi band information i.e. comprehending multiBandInfoList, disregarding in RRC_CONNECTED the related system information fields and understanding the EARFCN signalling for all bands, that overlap with the bands supported by the UE, and that are defined in the earliest version of TS 36.101[42] that includes all UE supported bands.

– This FGI bit is concerns an optional release independent feature (as it was difficult to introduce this from REL-8 when using regular UE capability signalling)

Rel-8

36.331, Annex B.1

pc_FeatrGrp_31_T

Corresponding to the Index of Indicator, the leftmost binary bit 31.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 31 in Table A.4.5-1a for FDD.

Yes

Rel-10

32

Undefined

Rel-8

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 32.

Table A.4.5-1c: Void

Table A.4.5-1d: Feature group indicators 33-64 for FDD

Item

Additional information

Notes

If indicated "Yes" the feature shall be implemented and successfully tested for the corresponding release

Release

Ref.

Mnemonic

Comments

1

Inter-RAT ANR features for UTRAN including:

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI

– can only be set to 1 if the UE has set bit number 5 and bit number 22 to 1.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_33_F

Corresponding to the Index of Indicator, the leftmost binary bit 33.
Set to true if supporting all functionalities in the feature group.

2

Inter-RAT ANR features for GERAN including:

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI

– can only be set to 1 if the UE has set bit number 5 and bit number 23 to 1.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_34_F

Corresponding to the Index of Indicator, the leftmost binary bit 34.
Set to true if supporting all functionalities in the feature group.

3

Inter-RAT ANR features for 1xRTT including:

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI

– can only be set to 1 if the UE has set bit number 5 and bit number 24 to 1.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_35_F

Corresponding to the Index of Indicator, the leftmost binary bit 35.
Set to true if supporting all functionalities in the feature group.

4

Inter-RAT ANR features for HRPD including:

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI

– can only be set to 1 if the UE has set bit number 5 and bit number 26 to 1.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_36_F

Corresponding to the Index of Indicator, the leftmost binary bit 36.
Set to true if supporting all functionalities in the feature group.

5

Inter-RAT ANR features for UTRAN TDD including:

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI

– can only be set to 1 if the UE has set bit number 5 and at least one of the bit number 22 (for UEs supporting only UTRA TDD) or the bit number 39 to 1.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_37_F

Corresponding to the Index of Indicator, the leftmost binary bit 37.

Set to true if supporting all functionalities in the feature group.

6

– EUTRA RRC_CONNECTED to UTRA TDD CELL_DCH PS handover, if the UE supports both UTRAN FDD and UTRAN TDD

– can only be set to 1 if the UE has set bit number 39 to 1.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_38_F

Corresponding to the Index of Indicator, the leftmost binary bit 38.

Set to true if supporting all functionalities in the feature group.

7

– UTRAN TDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports both UTRAN FDD and UTRAN TDD

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_39_F

Corresponding to the Index of Indicator, the leftmost binary bit 39.

Set to true if supporting all functionalities in the feature group.

8

– EUTRA RRC_CONNECTED to UTRA TDD CELL_DCH CS handover, if the UE supports both UTRAN FDD and UTRAN TDD

– related to SR-VCC

– can only be set to 1 if the UE has set bit number 38 to 1.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_40_F

Corresponding to the Index of Indicator, the leftmost binary bit 40.

Set to true if supporting all functionalities in the feature group.

9

Measurement reporting event: Event B1 – Neighbour > threshold for UTRAN FDD, if the UE supports UTRAN FDD and has set bit number 22 to 1

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Yes for FDD, unless UE has set bit number 15 to 1

Rel-9

36.331, Annex B.1

pc_FeatrGrp_41_F

Corresponding to the Index of Indicator, the leftmost binary bit 41.

Set to true if supporting all functionalities in the feature group.

10

DCI format 3a (TPC commands for PUCCH and PUSCH with single bit power adjustments)

Rel-13

36.331, Annex B.1

pc_FeatrGrp_42_F

Corresponding to the Index of Indicator, the leftmost binary bit 42.

11

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 43.

12

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 44.

13

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 45.

14

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 46.

15

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 47.

16

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 48.

17

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 49.

18

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 50.

19

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 51.

20

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 52.

21

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 53.

22

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 54.

23

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 55.

24

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 56.

25

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 57.

26

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 58.

27

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 59.

28

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 60.

29

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 61.

30

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 62.

31

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 63.

32

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 64.

Table A.4.5-1e: Feature group indicators 33-64 for TDD

Item

Additional information

Notes

If indicated "Yes" the feature shall be implemented and successfully tested for the corresponding release

Release

Ref.

Mnemonic

Comments

1

Inter-RAT ANR features for UTRAN including:

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI

– can only be set to 1 if the UE has set bit number 5 and bit number 22 to 1.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_33_T

Corresponding to the Index of Indicator, the leftmost binary bit 33.
Set to true if supporting all functionalities in the feature group.

2

Inter-RAT ANR features for GERAN including:

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI

– can only be set to 1 if the UE has set bit number 5 and bit number 23 to 1.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_34_T

Corresponding to the Index of Indicator, the leftmost binary bit 34.
Set to true if supporting all functionalities in the feature group.

3

Inter-RAT ANR features for 1xRTT including:

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI

– can only be set to 1 if the UE has set bit number 5 and bit number 24 to 1.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_35_T

Corresponding to the Index of Indicator, the leftmost binary bit 35.
Set to true if supporting all functionalities in the feature group.

4

Inter-RAT ANR features for HRPD including:

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI

– can only be set to 1 if the UE has set bit number 5 and bit number 26 to 1.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_36_T

Corresponding to the Index of Indicator, the leftmost binary bit 36.
Set to true if supporting all functionalities in the feature group.

5

Inter-RAT ANR features for UTRAN TDD including:

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON

– Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI

– can only be set to 1 if the UE has set bit number 5 and at least one of the bit number 22 (for UEs supporting only UTRA TDD) or the bit number 39 to 1.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_37_T

Corresponding to the Index of Indicator, the leftmost binary bit 37.

Set to true if supporting all functionalities in the feature group.

6

– EUTRA RRC_CONNECTED to UTRA TDD CELL_DCH PS handover, if the UE supports both UTRAN FDD and UTRAN TDD

– can only be set to 1 if the UE has set bit number 39 to 1.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_38_T

Corresponding to the Index of Indicator, the leftmost binary bit 38.

Set to true if supporting all functionalities in the feature group.

7

– UTRAN TDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports both UTRAN FDD and UTRAN TDD

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_39_T

Corresponding to the Index of Indicator, the leftmost binary bit 39.

Set to true if supporting all functionalities in the feature group.

8

– EUTRA RRC_CONNECTED to UTRA TDD CELL_DCH CS handover, if the UE supports both UTRAN FDD and UTRAN TDD

– related to SR-VCC

– can only be set to 1 if the UE has set bit number 38 to 1.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_40_T

Corresponding to the Index of Indicator, the leftmost binary bit 40.

Set to true if supporting all functionalities in the feature group.

9

Measurement reporting event: Event B1 – Neighbour > threshold for UTRAN FDD, if the UE supports UTRAN FDD and has set bit number 22 to 1

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-9

36.331, Annex B.1

pc_FeatrGrp_41_T

Corresponding to the Index of Indicator, the leftmost binary bit 41.

Set to true if supporting all functionalities in the feature group.

10

DCI format 3a (TPC commands for PUCCH and PUSCH with single bit power adjustments)

Rel-13

36.331, Annex B.1

pc_FeatrGrp_42_T

Corresponding to the Index of Indicator, the leftmost binary bit 42.

11

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 43.

12

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 44.

13

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 45.

14

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 46.

15

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 47.

16

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 48.

17

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 49.

18

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 50.

19

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 51.

20

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 52.

21

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 53.

22

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 54.

23

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 55.

24

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 56.

25

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 57.

26

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 58.

27

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 59.

28

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 60.

29

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 61.

30

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 62.

31

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 63.

32

Undefined

Rel-9

36.331, Annex B.1

Corresponding to the Index of Indicator, the leftmost binary bit 64.

Table A.4.5-2: EUTRA Feature group indicators

Item

Additional information

Notes

Ref.

Release

Mnemonic

Comments

1

Support of

– UTRA CELL_PCH to EUTRA RRC_IDLE cell reselection

– UTRA URA_PCH to EUTRA RRC_IDLE cell reselection

25.331, Annex E

Rel-8

pc_UTRA_FeatrGrp_1

Corresponding to the Index of Indicator, the leftmost binary bit 1

For Rel-8:

Set to true if supporting all functionalities in the feature group

For Rel-9 or later releases:

this FGI bit is set to TRUE s

2

Support of

– EUTRAN measurements and reporting in connected mode

25.331, Annex E

Rel-8

pc_UTRA_FeatrGrp_2

Corresponding to the Index of Indicator, the leftmost binary bit 2
Set to true if supporting all functionalities in the feature group

3

Support of

– UTRA CELL_FACH absolute priority cell reselection for high priority layers

25.331, Annex E

Rel-8 to Rel-10

pc_UTRA_FeatrGrp_3

Corresponding to the Index of Indicator, the leftmost binary bit 3
Set to true if supporting all functionalities in the feature group

UE supporting E-UTRAN shall set this bit to ‘TRUE’ in this version of specification.

Rel-11

4

Support of

– UTRA CELL_FACH absolute priority cell reselection for all layers

25.331, Annex E

Rel-8 to Rel-10

pc_UTRA_FeatrGrp_4

Corresponding to the Index of Indicator, the leftmost binary bit 4
Set to true if supporting all functionalities in the feature group

UE supporting E-UTRAN shall set this bit to ‘TRUE’ in this version of specification.

Rel-11

Table A.4.5-3: Void

Table A.4.5-3a: Release 10 AS feature group indicators 101-132 for FDD

Item

Additional information

Notes

If indicated "Yes" the feature shall be implemented and successfully tested for the corresponding release

Release

Ref.

Mnemonic

Comments

1

– DMRS with OCC (orthogonal cover code) and SGH (sequence group hopping) disabling

– if the UE supports two or more layers for spatial multiplexing in UL, this bit shall be set to 1.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_101_F

Corresponding to the Index of Indicator, the leftmost binary bit 101.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 1 in Table A.4.5-3b for TDD.

– If a category 0 UE does not support this feature, this bit shall be set to 0.

Rel-12

2

– Trigger type 1 SRS (aperiodic SRS) transmission (Up to X ports)

NOTE: X = number of supported layers on given band

Rel-10

36.331, Annex C.1

pc_FeatrGrp_102_F

Corresponding to the Index of Indicator, the leftmost binary bit 102.
Set to true if supporting all functionalities in the feature group.

3

– PDSCH transmission mode 9 when up to 4 CSI reference signal ports are configured

– for Category 8 UEs, this bit shall be set to 1.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_103_F

Corresponding to the Index of Indicator, the leftmost binary bit 103.
Set to true if supporting all functionalities in the feature group.

– for Category 8 UEs, this bit shall be set to 1.

– for Category 11 and higher UEs, this bit shall be set to 1.

– for DL Category 11 and higher UEs (except for DL Category 13), this bit shall be set to 1.

Yes for the UE categories listed in the column “Notes”

Rel-15

4

– PDSCH transmission mode 9 for TDD when 8 CSI reference signal ports are configured

– if the UE does not support TDD, this bit is irrelevant (capability signalling exists for FDD for this feature), and this bit shall be set to 0.

– for Category 8 UEs, this bit shall be set to 1.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_104_F

Corresponding to the Index of Indicator, the leftmost binary bit 104.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 4 in Table A.4.5-3b for TDD.

– if the UE does not support TDD, this bit is irrelevant, and this bit shall be set to 0.

– this bit is not applicable to FDD (capability signalling exists for FDD for this feature).

– for Category 8 UEs, this bit shall be set to 1.

– for Category 11 and higher UEs, this bit shall be set to 1.

– for DL Category 11 and higher UEs (except for DL Category 13), this bit shall be set to 1.

Yes for TDD, for the UE categories listed in the column “Notes”

Rel-15

5

– Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-0 – UE selected subband CQI without PMI, when PDSCH transmission mode 9 is configured

– Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI, when PDSCH transmission mode 9 and up to 4 CSI reference signal ports are configured

– this bit can be set to 1 only if indices 2 (Table B.1-1) and 103 are set to 1.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_105_F

Corresponding to the Index of Indicator, the leftmost binary bit 105.
Set to true if supporting all functionalities in the feature group.

– For UEs capable of TDD-FDD CA, this bit can be set to 1 for both FDD and TDD if index 2 is set to 1 for both FDD and TDD, and index 103 is set to 1 either for FDD and TDD.

Rel-12

6

– Periodic CQI/PMI/RI/PTI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI, when PDSCH transmission mode 9 and 8 CSI reference signal ports are configured

– this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’) and if index 2 (Table B.1-1) is set to 1.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_106_F

Corresponding to the Index of Indicator, the leftmost binary bit 106.
Set to true if supporting all functionalities in the feature group.

– For UEs capable of TDD-FDD CA, this bit can be set to 1 for both FDD and TDD if either index 104 is set to 1 or tm9-With-8Tx-FDD-r10 is set to ‘supported’, and if index 2 is set to 1 for both FDD and TDD.

Rel-12

7

– Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-0 – UE selected subband CQI without PMI, when PDSCH transmission mode 9 is configured

– Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI, when PDSCH transmission mode 9 and up to 4 CSI reference signal ports are configured

– this bit can be set to 1 only if indices 1 (Table B.1-1) and 103 are set to 1.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_107_F

Corresponding to the Index of Indicator, the leftmost binary bit 107.
Set to true if supporting all functionalities in the feature group.

8

– Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI, when PDSCH transmission mode 9 and 8 CSI reference signal ports are configured

– this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’) and if index 1 (Table B.1-1) is set to 1.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_108_F

Corresponding to the Index of Indicator, the leftmost binary bit 108.
Set to true if supporting all functionalities in the feature group.

9

– Periodic CQI/PMI/RI reporting on PUCCH Mode 1-1, submode 1

– this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’).

Rel-10

36.331, Annex C.1

pc_FeatrGrp_109_F

Corresponding to the Index of Indicator, the leftmost binary bit 109.
Set to true if supporting all functionalities in the feature group.

– For UEs capable of TDD-FDD CA, this bit can be set to 1 for both FDD and TDD if either index 104 is set to 1 or tm9-With-8Tx-FDD-r10 is set to ‘supported’.

Rel-12

10

– Periodic CQI/PMI/RI reporting on PUCCH Mode 1-1, submode 2

– this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’).

Rel-10

36.331, Annex C.1

pc_FeatrGrp_110_F

Corresponding to the Index of Indicator, the leftmost binary bit 110.
Set to true if supporting all functionalities in the feature group.

– For UEs capable of TDD-FDD CA, this bit can be set to 1 for both FDD and TDD if either index 104 is set to 1 or tm9-With-8Tx-FDD-r10 is set to ‘supported’.

Rel-12

11

– Measurement reporting trigger Event A6

– this bit can be set to 1 only if the UE supports carrier aggregation.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_111_F

Corresponding to the Index of Indicator, the leftmost binary bit 111.
Set to true if supporting all functionalities in the feature group.

12

– SCell addition within the Handover to EUTRA procedure

– this bit can be set to 1 only if the UE supports carrier aggregation and the Handover to EUTRA procedure.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_112_F

Corresponding to the Index of Indicator, the leftmost binary bit 112.
Set to true if supporting all functionalities in the feature group.

13

– Trigger type 0 SRS (periodic SRS) transmission on X Serving Cells

NOTE: X = number of supported component carriers in a given band combination

– this bit can be set to 1 only if the UE supports carrier aggregation in UL.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_113_F

Corresponding to the Index of Indicator, the leftmost binary bit 113.
Set to true if supporting all functionalities in the feature group.

14

– Reporting of both UTRA CPICH RSCP and Ec/N0 in a Measurement Report

– this bit can be set to 1 only if index 22 (Table B.1-1) is set to 1.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_114_F

Corresponding to the Index of Indicator, the leftmost binary bit 114.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 14 in Table A.4.5-3b for TDD.

15

– time domain ICIC RLM/RRM measurement subframe restriction for the serving cell

– time domain ICIC RRM measurement subframe restriction for neighbour cells

– time domain ICIC CSI measurement subframe restriction

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_115_F

Corresponding to the Index of Indicator, the leftmost binary bit 115.
Set to true if supporting all functionalities in the feature group.

16

– Relative transmit phase continuity for spatial multiplexing in UL

– this bit can be set to 1 only if the UE supports two or more layers for spatial multiplexing in UL.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_116_F

Corresponding to the Index of Indicator, the leftmost binary bit 116.
Set to true if supporting all functionalities in the feature group.

17

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 117.

18

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 118.

19

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 119.

20

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 120.

21

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 121.

22

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 122.

23

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 123.

24

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 124.

25

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 125.

26

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 126.

27

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 127.

28

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 128.

29

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 129.

30

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 130.

31

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 131.

32

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 132.

Table A.4.5-3b: Release 10 AS feature group indicators 101-132 for TDD

Item

Additional information

Notes

If indicated "Yes" the feature shall be implemented and successfully tested for the corresponding release

Release

Ref.

Mnemonic

Comments

1

– DMRS with OCC (orthogonal cover code) and SGH (sequence group hopping) disabling

– if the UE supports two or more layers for spatial multiplexing in UL, this bit shall be set to 1.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_101_T

Corresponding to the Index of Indicator, the leftmost binary bit 101.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 1 in Table A.4.5-3a for FDD.

– If a category 0 UE does not support this feature, this bit shall be set to 0.

Rel-12

2

– Trigger type 1 SRS (aperiodic SRS) transmission (Up to X ports)

NOTE: X = number of supported layers on given band

Rel-10

36.331, Annex C.1

pc_FeatrGrp_102_T

Corresponding to the Index of Indicator, the leftmost binary bit 102.
Set to true if supporting all functionalities in the feature group.

3

– PDSCH transmission mode 9 when up to 4 CSI reference signal ports are configured

– for Category 8 UEs, this bit shall be set to 1.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_103_T

Corresponding to the Index of Indicator, the leftmost binary bit 103.
Set to true if supporting all functionalities in the feature group.

– for Category 8 UEs, this bit shall be set to 1.

– for Category 11 and higher UEs, this bit shall be set to 1.

– for DL Category 11 and higher UEs (except for DL Category 13), this bit shall be set to 1.

Yes for the UE categories listed in the column “Notes”

Rel-15

4

– PDSCH transmission mode 9 for TDD when 8 CSI reference signal ports are configured

– if the UE does not support TDD, this bit is irrelevant (capability signalling exists for FDD for this feature), and this bit shall be set to 0.

– for Category 8 UEs, this bit shall be set to 1.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_104_T

Corresponding to the Index of Indicator, the leftmost binary bit 104.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 4 in Table A.4.5-3a for FDD.

– if the UE does not support TDD, this bit is irrelevant, and this bit shall be set to 0.

– this bit is not applicable to FDD (capability signalling exists for FDD for this feature).

– for Category 8 UEs, this bit shall be set to 1.

– for Category 11 and higher UEs, this bit shall be set to 1.

– for DL Category 11 and higher UEs (except for DL Category 13), this bit shall be set to 1.

Yes for TDD, for the UE categories listed in the column “Notes”

Rel-15

5

– Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-0 – UE selected subband CQI without PMI, when PDSCH transmission mode 9 is configured

– Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI, when PDSCH transmission mode 9 and up to 4 CSI reference signal ports are configured

– this bit can be set to 1 only if indices 2 (Table B.1-1) and 103 are set to 1.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_105_T

Corresponding to the Index of Indicator, the leftmost binary bit 105.
Set to true if supporting all functionalities in the feature group.

– For UEs capable of TDD-FDD CA, this bit can be set to 1 for both FDD and TDD if index 2 is set to 1 for both FDD and TDD, and index 103 is set to 1 either for FDD and TDD.

Rel-12

6

– Periodic CQI/PMI/RI/PTI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI, when PDSCH transmission mode 9 and 8 CSI reference signal ports are configured

– this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’) and if index 2 (Table B.1-1) is set to 1.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_106_T

Corresponding to the Index of Indicator, the leftmost binary bit 106.
Set to true if supporting all functionalities in the feature group.

– For UEs capable of TDD-FDD CA, this bit can be set to 1 for both FDD and TDD if either index 104 is set to 1 or tm9-With-8Tx-FDD-r10 is set to ‘supported’, and if index 2 is set to 1 for both FDD and TDD.

Rel-12

7

– Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-0 – UE selected subband CQI without PMI, when PDSCH transmission mode 9 is configured

– Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI, when PDSCH transmission mode 9 and up to 4 CSI reference signal ports are configured

– this bit can be set to 1 only if indices 1 (Table B.1-1) and 103 are set to 1.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_107_T

Corresponding to the Index of Indicator, the leftmost binary bit 107.
Set to true if supporting all functionalities in the feature group.

8

– Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI, when PDSCH transmission mode 9 and 8 CSI reference signal ports are configured

– this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’) and if index 1 (Table B.1-1) is set to 1.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_108_T

Corresponding to the Index of Indicator, the leftmost binary bit 108.
Set to true if supporting all functionalities in the feature group.

9

– Periodic CQI/PMI/RI reporting on PUCCH Mode 1-1, submode 1

– this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’).

Rel-10

36.331, Annex C.1

pc_FeatrGrp_109_T

Corresponding to the Index of Indicator, the leftmost binary bit 109.
Set to true if supporting all functionalities in the feature group.

– For UEs capable of TDD-FDD CA, this bit can be set to 1 for both FDD and TDD if either index 104 is set to 1 or tm9-With-8Tx-FDD-r10 is set to ‘supported’.

Rel-12

10

– Periodic CQI/PMI/RI reporting on PUCCH Mode 1-1, submode 2

– this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’).

Rel-10

36.331, Annex C.1

pc_FeatrGrp_110_T

Corresponding to the Index of Indicator, the leftmost binary bit 110.
Set to true if supporting all functionalities in the feature group.

– For UEs capable of TDD-FDD CA, this bit can be set to 1 for both FDD and TDD if either index 104 is set to 1 or tm9-With-8Tx-FDD-r10 is set to ‘supported’.

Rel-12

11

– Measurement reporting trigger Event A6

– this bit can be set to 1 only if the UE supports carrier aggregation.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_111_T

Corresponding to the Index of Indicator, the leftmost binary bit 111.
Set to true if supporting all functionalities in the feature group.

12

– SCell addition within the Handover to EUTRA procedure

– this bit can be set to 1 only if the UE supports carrier aggregation and the Handover to EUTRA procedure.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_112_T

Corresponding to the Index of Indicator, the leftmost binary bit 112.
Set to true if supporting all functionalities in the feature group.

13

– Trigger type 0 SRS (periodic SRS) transmission on X Serving Cells

NOTE: X = number of supported component carriers in a given band combination

– this bit can be set to 1 only if the UE supports carrier aggregation in UL.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_113_T

Corresponding to the Index of Indicator, the leftmost binary bit 113.
Set to true if supporting all functionalities in the feature group.

14

– Reporting of both UTRA CPICH RSCP and Ec/N0 in a Measurement Report

– this bit can be set to 1 only if index 22 (Table B.1-1) is set to 1.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_114_T

Corresponding to the Index of Indicator, the leftmost binary bit 114.
Set to true if supporting all functionalities in the feature group.

If UE supports FDD and TDD this item shall be set to same value as for item 14 in Table A.4.5-3a for FDD.

15

– time domain ICIC RLM/RRM measurement subframe restriction for the serving cell

– time domain ICIC RRM measurement subframe restriction for neighbour cells

– time domain ICIC CSI measurement subframe restriction

– If a category M1 or M2 UE does not support this feature group, this bit shall be set to 0.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_115_T

Corresponding to the Index of Indicator, the leftmost binary bit 115.
Set to true if supporting all functionalities in the feature group.

16

– Relative transmit phase continuity for spatial multiplexing in UL

– this bit can be set to 1 only if the UE supports two or more layers for spatial multiplexing in UL.

Rel-10

36.331, Annex C.1

pc_FeatrGrp_116_T

Corresponding to the Index of Indicator, the leftmost binary bit 116.
Set to true if supporting all functionalities in the feature group.

17

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 117.

18

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 118.

19

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 119.

20

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 120.

21

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 121.

22

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 122.

23

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 123.

24

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 124.

25

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 125.

26

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 126.

27

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 127.

28

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 128.

29

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 129.

30

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 130.

31

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 131.

32

Undefined

Rel-10

36.331, Annex C.1

Corresponding to the Index of Indicator, the leftmost binary bit 132.

Annex B (informative):
Test Case Branching