A.4.4 Feature group indicators
36.521-23GPPEvolved Universal Terrestrial Radio Access (E-UTRA)Part 2: Implementation Conformance Statement (ICS)Radio transmission and receptionRelease 17TSUser Equipment (UE) conformance specification
In Table A.4.4-1a and Table A.4.4-1b, a ‘VoLTE capable UE’ corresponds to a UE that is capable of the "Voice domain preference for E-UTRAN" defined in TS 24.301 [15] being set to "IMS PS voice only", "IMS PS voice preferred, CS voice as secondary" or "CS voice preferred, IMS PS voice as secondary" (Ref TS 36.331 [14], clause B.1)
When a UE supports E-UTRA FDD only, it’s required to indicate combined FGI capabilities in Table A.4.4-1a, Table A.4.4-2a and Table A.4.4-3a; when a UE supports E-UTRA TDD only, it’s required to indicate combined FGI capabilities in Table A.4.4-1b, Table A.4.4-2b and Table A.4.4-3b; when a UE supports E-UTRA FDD/TDD dual mode with same FGI capabilities on FDD and TDD, it’s required to indicate both FGI capabilities in Table A.4.4-1a, Table A.4.4-2a, Table A.4.4-3a, Table A.4.4-1b, Table A.4.4-2b and Table A.4.4-3b and make sure those FDD and TDD tables are identical.
Note 1: From Rel-11 onwards 3GPP TSG RAN has discontinued the usage of FGI bits. Instead it has introduced a different mechanism to accomplish the same purposes based on the principles described in TS 36.306 [17] clause 4. This new principles where applicable have been catered for in section A.4.5, e.g. Table A.4.5-2.
Table A.4.4-1:Void
Table A.4.4-1a: Feature group indicators 1-32 for FDD
Item |
Additional information |
Notes |
If indicated "Yes" the feature shall be implemented and successfully tested for the corresponding release |
Release |
Ref. |
Mnemonic |
Comments |
---|---|---|---|---|---|---|---|
1 |
Support of – Intra-subframe frequency hopping for PUSCH scheduled by UL grant – DCI format 3a (TPC commands for PUCCH and PUSCH with single bit power adjustments) – Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-0 – UE selected subband CQI without PMI – Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI |
– set to 1 by category M1 UE that has implemented and successfully tested "Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-0 – UE selected subband CQI without PM" |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_1_F |
Corresponding to the Index of Indicator, the leftmost binary bit 1. |
|
2 |
Support of – Simultaneous CQI and ACK/NACK on PUCCH, i.e. PUCCH format 2a and 2b – Absolute TPC command for PUSCH – Resource allocation type 1 for PDSCH – Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-0 – UE selected subband CQI without PMI – Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_2_F |
Corresponding to the Index of Indicator, the leftmost binary bit 2. |
|
3 |
Support of – Semi-persistent scheduling – TTI bundling – 5bit RLC UM SN – 7bit PDCP SN |
– can only be set to 1 if the UE has set bit number 7 to 1. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_3_F |
Corresponding to the Index of Indicator, the leftmost binary bit 3. |
|
Support of – 5bit RLC UM SN – 7bit PDCP SN |
– can only be set to 1 if the UE has set bit number 7 to 1. |
Yes, if UE supports VoLTE |
Rel-9, Rel-10 |
||||
Yes, if UE supports VoLTE. Yes, if UE supports SRVCC to EUTRAN from GERAN. |
Rel-11 |
||||||
4 |
Support of – Short DRX cycle |
– can only be set to 1 if the UE has set bit number 5 to 1. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_4_F |
Corresponding to the Index of Indicator, the leftmost binary bit 4. |
|
5 |
Support of – Long DRX cycle – DRX command MAC control element |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_5_F |
Corresponding to the Index of Indicator, the leftmost binary bit 5. |
||
Yes |
Rel-9 |
||||||
6 |
Support of – Prioritized bit rate |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_6_F |
Corresponding to the Index of Indicator, the leftmost binary bit 6. |
||
Yes |
Rel-9 |
||||||
7 |
Support of – RLC UM |
– can only be set to 0 if the UE does not support voice |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_7_F |
Corresponding to the Index of Indicator, the leftmost binary bit 7. |
|
Yes, if UE supports VoLTE |
Rel-9 |
||||||
Yes, if UE supports VoLTE. Yes, if UE supports SRVCC to EUTRAN from GERAN. |
Rel-11 |
||||||
8 |
Support of – EUTRA RRC_CONNECTED to UTRA CELL_DCH PS handover |
– can only be set to 1 if the UE has set bit number 22 to 1 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_8_F |
Corresponding to the Index of Indicator, the leftmost binary bit 8. |
|
Support of – EUTRA RRC_CONNECTED to UTRA FDD or UTRA TDD CELL_DCH PS handover, if the UE supports either only UTRAN FDD or only UTRAN TDD – EUTRA RRC_CONNECTED to UTRA FDD CELL_DCH PS handover, if the UE supports both UTRAN FDD and UTRAN TDD |
Yes (except for category M1 UE), if UE supports UTRA FDD |
Rel-9 |
|||||
9 |
Support of – EUTRA RRC_CONNECTED to GERAN GSM_Dedicated handover |
– related to SR-VCC – can only be set to 1 if the UE has set bit number 23 to 1 |
Rel-8, Rel-9, Rel-10 |
36.331, Annex B.1 |
pc_FeatrGrp_9_F |
Corresponding to the Index of Indicator, the leftmost binary bit 9. |
|
Yes (except for category M1 UE), if UE supports SRVCC to EUTRAN from GERAN. |
Rel-11 |
||||||
10 |
Support of – EUTRA RRC_CONNECTED to GERAN (Packet_)Idle by Cell Change Order – EUTRA RRC_CONNECTED to GERAN (Packet_)Idle by Cell Change Order with NACC (Network Assisted Cell Change) |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_10_F |
Corresponding to the Index of Indicator, the leftmost binary bit 10. |
||
11 |
Support of – EUTRA RRC_CONNECTED to CDMA2000 1xRTT CS Active handover |
– can only be set to 1 if the UE has sets bit number 24 to 1 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_11_F |
Corresponding to the Index of Indicator, the leftmost binary bit 11. |
|
12 |
Support of – EUTRA RRC_CONNECTED to CDMA2000 HRPD Active handover |
– can only be set to 1 if the UE has set bit number 26 to 1 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_12_F |
Corresponding to the Index of Indicator, the leftmost binary bit 12. |
|
13 |
Support of – Inter-frequency handover (within FDD or TDD) |
– can only be set to 1 if the UE has set bit number 25 to 1 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_13_F |
Corresponding to the Index of Indicator, the leftmost binary bit 13. |
|
Yes (except for category M1 UE), unless UE only supports band 13 |
Rel-9 |
||||||
14 |
Support of – Measurement reporting event: Event A4 – Neighbour > threshold – Measurement reporting event: Event A5 – Serving < threshold1 & Neighbour > threshold2 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_14_F |
Corresponding to the Index of Indicator, the leftmost binary bit 14. Set to true if supporting all functionalities in the feature group. |
||
Yes (except for category M1 UE) |
Rel-9 |
||||||
15 |
Support of – Measurement reporting event: Event B1 – Neighbour > threshold for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1 – Measurement reporting event: Event B1 – Neighbour > threshold for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively – Measurement reporting event: Event B1 – Neighbour > threshold for GERAN, 1xRTT or HRPD, if the UE has set bit number 23, 24 or 26 to 1, respectively |
– can only be set to 1 if the UE has set at least one of the bit number 22, 23, 24, 26 or 39 to 1. – even if the UE sets bits 41, it shall still set bit 15 to 1 if measurement reporting event B1 is tested for all RATs supported by UE – If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_15_F |
Corresponding to the Index of Indicator, the leftmost binary bit 15. Set to true if supporting all functionalities in the feature group. |
|
Yes for FDD, if UE supports only UTRAN FDD and does not support UTRAN TDD or GERAN or 1xRTT or HRPD |
Rel-9 |
||||||
16 |
Support of – Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells; – Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells, if the UE has set bit number 25 to 1; and – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN, GERAN, 1xRTT or HRPD, if the UE has set bit number 22, 23, 24 or 26 to 1, respectively. NOTE: Event triggered periodical reporting (i.e. with triggerType set to event and with reportAmount > 1) is a mandatory functionality of event triggered reporting and therefore not the subject of this bit. Support of – Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells – Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells, if the UE has set bit number 25 to 1 – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1 – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, 1xRTT or HRPD, if the UE has set bit number 23, 24 or 26 to 1, respectively. NOTE: Event triggered periodical reporting (i.e., with triggerType set to event and with reportAmount > 1) is a mandatory functionality of event triggered reporting and therefore not the subject of this bit. |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_16_F |
Corresponding to the Index of Indicator, the leftmost binary bit 16. |
|
Yes |
Rel-9 |
||||||
17 |
Support of Intra-frequency ANR features including: – Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells – Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI |
– can only be set to 1 if the UE has set bit number 5 to 1. – If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_17_F |
Corresponding to the Index of Indicator, the leftmost binary bit 17. |
|
Yes |
Rel-9 |
||||||
18 |
Support of Inter-frequency ANR features including: – Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells – Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI |
– can only be set to 1 if the UE has set bit number 5 to 1. – If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_18_F |
Corresponding to the Index of Indicator, the leftmost binary bit 18. |
|
Yes, unless UE only supports band 13 |
Rel-9 |
||||||
19 |
Support of Inter-RAT ANR features including: – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, if the UE has set bit number 23 to 1 – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN, 1xRTT or HRPD, if the UE has set bit number 22, 24 or 26 to 1, respectively – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for UTRAN, GERAN, 1xRTT or HRPD, if the UE has set bit number 22, 23, 24 or 26 to 1, respectively |
– can only be set to 1 if the UE has set bit number 5 to 1 and the UE has set at least one of the bit number 22, 23, 24 or 26 to 1. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_19_F |
Corresponding to the Index of Indicator, the leftmost binary bit 19. |
|
Support of Inter-RAT ANR features including: – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, if the UE has set bit number 23 to 1 – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1 – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for 1xRTT or HRPD, if the UE has set bit number 24 or 26 to 1, respectively – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRANTDD and has set bit number 22 to 1 – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for GERAN, 1xRTT or HRPD, if the UE has set bit number 23, 24 or 26 to 1, respectively |
– can only be set to 1 if the UE has set bit number 5 to 1 and the UE has set at least one of the bit number 22, 39, 23, 24 or 26 to 1. – even if the UE sets bits 33 to 37, it shall still set bit 19 to 1 if inter-RAT ANR features are tested for all RATs for which inter-RAT measurement reporting is indicated as tested |
Rel-9 |
|||||
20 |
If bit number 7 is set to ‘ 0’: – SRB1 and SRB2 for DCCH + 8x AM DRB If bit number 7 is set to ‘ 1’: – SRB1 and SRB2 for DCCH + 8x AM DRB – SRB1 and SRB2 for DCCH + 5x AM DRB + 3x UM DRB NOTE: UE which indicate support for a DRB combination also support all subsets of the DRB combination. Therefore, release of DRB(s) never results in an unsupported DRB combination. |
– Regardless of what bit number 7 and bit number 20 is set to, UE shall support at least SRB1 and SRB2 for DCCH + 4x AM DRB – Regardless of what bit number 20 is set to, if bit number 7 is set to ‘ 1’, UE shall support at least SRB1 and SRB2 for DCCH + 4x AM DRB + 1x UM DRB |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_20_F |
Corresponding to the Index of Indicator, the leftmost binary bit 20. |
|
Yes |
Rel-9 |
||||||
21 |
Support of – Predefined intra- and inter-subframe frequency hopping for PUSCH with N_sb > 1 – Predefined inter-subframe frequency hopping for PUSCH with N_sb > 1 |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_21_F |
Corresponding to the Index of Indicator, the leftmost binary bit 21. |
|
22 |
Support of – UTRAN measurements, reporting and measurement reporting event B2 in E-UTRA connected mode |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_22_F |
Corresponding to the Index of Indicator, the leftmost binary bit 22. |
|
Support of – UTRAN FDD or UTRAN TDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports either only UTRAN FDD or only UTRAN TDD – UTRAN FDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports both UTRAN FDD and UTRAN TDD |
Yes for FDD, if UE supports UTRA FDD |
Rel-9 |
|||||
23 |
Support of – GERAN measurements, reporting and measurement reporting event B2 in E-UTRA connected mode |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_23_F |
Corresponding to the Index of Indicator, the leftmost binary bit 23. |
|
24 |
Support of – 1xRTT measurements, reporting and measurement reporting event B2 in E-UTRA connected mode |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_24_F |
Corresponding to the Index of Indicator, the leftmost binary bit 24. |
|
Yes, if UE supports enhanced 1xRTT CSFB |
Rel-9 |
||||||
25 |
Support of – Inter-frequency measurements and reporting in E-UTRA connected mode NOTE: The UE setting this bit to 1 and indicating support for FDD and TDD frequency bands in the UE capability signalling implements and is tested for FDD measurements while the UE is in TDD, and for TDD measurements while the UE is in FDD. |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_25_F |
Corresponding to the Index of Indicator, the leftmost binary bit 25. |
|
Yes, unless UE only supports band 13 |
Rel-9 |
||||||
26 |
Support of – HRPD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_26_F |
Corresponding to the Index of Indicator, the leftmost binary bit 26. |
|
Yes, if UE supports HRPD |
Rel-9 |
||||||
27 |
Support of – EUTRA RRC_CONNECTED to UTRA CELL_DCH CS handover |
– related to SR-VCC – can only be set to 1 if the UE has set bit number 8 to 1 and supports SR-VCC from EUTRA defined in TS 24.008 – If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_27_F |
Corresponding to the Index of Indicator, the leftmost binary bit 27. Set to true if supporting all functionalities in the feature group. |
|
Support of – EUTRA RRC_CONNECTED to UTRA FDD or UTRA TDD CELL_DCH CS handover, if the UE supports either only UTRAN FDD or only UTRAN TDD – EUTRA RRC_CONNECTED to UTRA FDD CELL_DCH CS handover, if the UE supports both UTRAN FDD and UTRAN TDD |
Yes for FDD, if UE supports VoLTE and UTRA FDD |
Rel-9 |
|||||
28 |
Support of – TTI bundling |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Yes for FDD |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_28_F |
Corresponding to the Index of Indicator, the leftmost binary bit 28. Set to true if supporting all functionalities in the feature group. |
29 |
Support of – Semi-Persistent Scheduling |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_29_F |
Corresponding to the Index of Indicator, the leftmost binary bit 29. |
|
30 |
Support of – Handover between FDD and TDD |
– can only be set to 1 if the UE has set bit number 13 to 1 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_30_F |
Corresponding to the Index of Indicator, the leftmost binary bit 30. |
|
31 |
Support of – Indicates whether the UE supports the mechanisms defined for cells broadcasting multi band information i.e. comprehending multiBandInfoList, disregarding in RRC_CONNECTED the related system information fields and understanding the EARFCN signalling for all bands, that overlap with the bands supported by the UE, and that are defined in the earliest version of TS 36.101 [42] that includes all UE supported bands. |
– In this release of the protocol, this bit will never be mandated to be set to 1 – This FGI bit concerns an optional release independent feature (as it was difficult to introduce this from REL-8 when using regular UE capability signalling) |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_31_F |
Corresponding to the Index of Indicator, the leftmost binary bit 31. Set to true if supporting all functionalities in the feature group. |
|
Rel-9 |
|||||||
Yes |
Rel-10 |
||||||
32 |
Undefined |
Rel-8 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 32. |
Table A.4.4-1b: Feature group indicators 1-32 for TDD
Item |
Additional information |
Notes |
If indicated "Yes" the feature shall be implemented and successfully tested for the corresponding release |
Release |
Ref. |
Mnemonic |
Comments |
---|---|---|---|---|---|---|---|
1 |
Support of – Intra-subframe frequency hopping for PUSCH scheduled by UL grant – DCI format 3a (TPC commands for PUCCH and PUSCH with single bit power adjustments) – Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-0 – UE selected subband CQI without PMI – Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI |
– set to 1 by category M1 UE that has implemented and successfully tested "Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-0 – UE selected subband CQI without PM" |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_1_T |
Corresponding to the Index of Indicator, the leftmost binary bit 1. |
|
2 |
Support of – Simultaneous CQI and ACK/NACK on PUCCH, i.e. PUCCH format 2a and 2b – Absolute TPC command for PUSCH – Resource allocation type 1 for PDSCH – Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-0 – UE selected subband CQI without PMI – Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_2_T |
Corresponding to the Index of Indicator, the leftmost binary bit 2. |
|
3 |
Support of – Semi-persistent scheduling – TTI bundling – 5bit RLC UM SN – 7bit PDCP SN |
– can only be set to 1 if the UE has set bit number 7 to 1. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_3_T |
Corresponding to the Index of Indicator, the leftmost binary bit 3. |
|
Support of – 5bit RLC UM SN – 7bit PDCP SN |
– can only be set to 1 if the UE has set bit number 7 to 1. |
Yes, if UE supports VoLTE |
Rel-9, Rel-10 |
||||
Yes, if UE supports VoLTE. Yes, if UE supports SRVCC to EUTRAN from GERAN. |
Rel-11 |
||||||
4 |
Support of – Short DRX cycle |
– can only be set to 1 if the UE has set bit number 5 to 1. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_4_T |
Corresponding to the Index of Indicator, the leftmost binary bit 4. |
|
5 |
Support of – Long DRX cycle – DRX command MAC control element |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_5_T |
Corresponding to the Index of Indicator, the leftmost binary bit 5. |
||
Yes |
Rel-9 |
||||||
6 |
Support of – Prioritized bit rate |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_6_T |
Corresponding to the Index of Indicator, the leftmost binary bit 6. |
||
Yes |
Rel-9 |
||||||
7 |
Support of – RLC UM |
– can only be set to 0 if the UE does not support voice |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_7_T |
Corresponding to the Index of Indicator, the leftmost binary bit 7. |
|
Yes, if UE supports VoLTE |
Rel-9 |
||||||
Yes, if UE supports VoLTE. Yes, if UE supports SRVCC to EUTRAN from GERAN. |
Rel-11 |
||||||
8 |
Support of – EUTRA RRC_CONNECTED to UTRA CELL_DCH PS handover |
– can only be set to 1 if the UE has set bit number 22 to 1 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_8_T |
Corresponding to the Index of Indicator, the leftmost binary bit 8. |
|
Support of – EUTRA RRC_CONNECTED to UTRA FDD or UTRA TDD CELL_DCH PS handover, if the UE supports either only UTRAN FDD or only UTRAN TDD – EUTRA RRC_CONNECTED to UTRA FDD CELL_DCH PS handover, if the UE supports both UTRAN FDD and UTRAN TDD |
Yes, if UE supports UTRA |
Rel-9 |
|||||
9 |
Support of – EUTRA RRC_CONNECTED to GERAN GSM_Dedicated handover |
– related to SR-VCC – can only be set to 1 if the UE has set bit number 23 to 1 |
Rel-8, Rel-9, Rel-10 |
36.331, Annex B.1 |
pc_FeatrGrp_9_T |
Corresponding to the Index of Indicator, the leftmost binary bit 9. |
|
Yes (except for category M1 UE), if UE supports SRVCC to EUTRAN from GERAN. |
Rel-11 |
||||||
10 |
Support of – EUTRA RRC_CONNECTED to GERAN (Packet_)Idle by Cell Change Order – EUTRA RRC_CONNECTED to GERAN (Packet_)Idle by Cell Change Order with NACC (Network Assisted Cell Change) |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_10_T |
Corresponding to the Index of Indicator, the leftmost binary bit 10. |
||
11 |
Support of – EUTRA RRC_CONNECTED to CDMA2000 1xRTT CS Active handover |
– can only be set to 1 if the UE has sets bit number 24 to 1 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_11_T |
Corresponding to the Index of Indicator, the leftmost binary bit 11. |
|
12 |
Support of – EUTRA RRC_CONNECTED to CDMA2000 HRPD Active handover |
– can only be set to 1 if the UE has set bit number 26 to 1 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_12_T |
Corresponding to the Index of Indicator, the leftmost binary bit 12. |
|
13 |
Support of – Inter-frequency handover (within FDD or TDD) |
– can only be set to 1 if the UE has set bit number 25 to 1 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_13_T |
Corresponding to the Index of Indicator, the leftmost binary bit 13. |
|
Yes (except for category M1 UE), unless UE only supports band 13 |
Rel-9 |
||||||
14 |
Support of – Measurement reporting event: Event A4 – Neighbour > threshold – Measurement reporting event: Event A5 – Serving < threshold1 & Neighbour > threshold2 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_14_T |
Corresponding to the Index of Indicator, the leftmost binary bit 14. Set to true if supporting all functionalities in the feature group. |
||
Yes (except for category M1 UE) |
Rel-9 |
||||||
15 |
Support of – Measurement reporting event: Event B1 – Neighbour > threshold for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1 – Measurement reporting event: Event B1 – Neighbour > threshold for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively – Measurement reporting event: Event B1 – Neighbour > threshold for GERAN, 1xRTT or HRPD, if the UE has set bit number 23, 24 or 26 to 1, respectively |
– can only be set to 1 if the UE has set at least one of the bit number 22, 23, 24, 26 or 39 to 1. – even if the UE sets bits 41, it shall still set bit 15 to 1 if measurement reporting event B1 is tested for all RATs supported by UE – If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_15_T |
Corresponding to the Index of Indicator, the leftmost binary bit 15. Set to true if supporting all functionalities in the feature group. |
|
Yes for FDD, if UE supports only UTRAN FDD and does not support UTRAN TDD or GERAN or 1xRTT or HRPD |
Rel-9 |
||||||
16 |
Support of – Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells; – Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells, if the UE has set bit number 25 to 1; and – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN, GERAN, 1xRTT or HRPD, if the UE has set bit number 22, 23, 24 or 26 to 1, respectively. NOTE: Event triggered periodical reporting (i.e. with triggerType set to event and with reportAmount > 1) is a mandatory functionality of event triggered reporting and therefore not the subject of this bit. Support of – Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells – Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells, if the UE has set bit number 25 to 1 – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1 – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, 1xRTT or HRPD, if the UE has set bit number 23, 24 or 26 to 1, respectively. NOTE: Event triggered periodical reporting (i.e., with triggerType set to event and with reportAmount > 1) is a mandatory functionality of event triggered reporting and therefore not the subject of this bit. |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_16_T |
Corresponding to the Index of Indicator, the leftmost binary bit 16. |
|
Yes |
Rel-9 |
||||||
17 |
Support of Intra-frequency ANR features including: – Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells – Intra-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI |
– can only be set to 1 if the UE has set bit number 5 to 1. – If a category M1 UE does not support this feature group, this bit shall be set to 0 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_17_T |
Corresponding to the Index of Indicator, the leftmost binary bit 17. |
|
Yes |
Rel-9 |
||||||
18 |
Support of Inter-frequency ANR features including: – Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells – Inter-frequency periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI |
– can only be set to 1 if the UE has set bit number 5 to 1. – If a category M1 UE does not support this feature group, this bit shall be set to 0 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_18_T |
Corresponding to the Index of Indicator, the leftmost binary bit 18. |
|
Yes, unless UE only supports band 13 |
Rel-9 |
||||||
19 |
Support of Inter-RAT ANR features including: – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, if the UE has set bit number 23 to 1 – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN, 1xRTT or HRPD, if the UE has set bit number 22, 24 or 26 to 1, respectively – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for UTRAN, GERAN, 1xRTT or HRPD, if the UE has set bit number 22, 23, 24 or 26 to 1, respectively |
– can only be set to 1 if the UE has set bit number 5 to 1 and the UE has set at least one of the bit number 22, 23, 24 or 26 to 1. |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_19_T |
Corresponding to the Index of Indicator, the leftmost binary bit 19. |
|
Support of Inter-RAT ANR features including: – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells for GERAN, if the UE has set bit number 23 to 1 – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRAN TDD and has set bit number 22 to 1 – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON for 1xRTT or HRPD, if the UE has set bit number 24 or 26 to 1, respectively – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for UTRAN FDD or UTRAN TDD, if the UE supports either only UTRAN FDD or only UTRANTDD and has set bit number 22 to 1 – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for UTRAN FDD or UTRAN TDD, if the UE supports both UTRAN FDD and UTRAN TDD and has set bit number 22 or 39 to 1, respectively – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI for GERAN, 1xRTT or HRPD, if the UE has set bit number 23, 24 or 26 to 1, respectively |
– can only be set to 1 if the UE has set bit number 5 to 1 and the UE has set at least one of the bit number 22, 39, 23, 24 or 26 to 1. – even if the UE sets bits 33 to 37, it shall still set bit 19 to 1 if inter-RAT ANR features are tested for all RATs for which inter-RAT measurement reporting is indicated as tested |
Rel-9 |
|||||
20 |
If bit number 7 is set to ‘0’: – SRB1 and SRB2 for DCCH + 8x AM DRB If bit number 7 is set to ‘1’: – SRB1 and SRB2 for DCCH + 8x AM DRB – SRB1 and SRB2 for DCCH + 5x AM DRB + 3x UM DRB NOTE: UE which indicate support for a DRB combination also support all subsets of the DRB combination. Therefore, release of DRB(s) never results in an unsupported DRB combination. |
– Regardless of what bit number 7 and bit number 20 is set to, UE shall support at least SRB1 and SRB2 for DCCH + 4x AM DRB – Regardless of what bit number 20 is set to, if bit number 7 is set to ‘1’, UE shall support at least SRB1 and SRB2 for DCCH + 4x AM DRB + 1x UM DRB |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_20_T |
Corresponding to the Index of Indicator, the leftmost binary bit 20. |
|
Yes |
Rel-9 |
||||||
21 |
Support of – Predefined intra- and inter-subframe frequency hopping for PUSCH with N_sb > 1 – Predefined inter-subframe frequency hopping for PUSCH with N_sb > 1 |
– If a category M1 UE does not support this feature group, this bit shall be set to 0 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_21_T |
Corresponding to the Index of Indicator, the leftmost binary bit 21. |
|
22 |
Support of – UTRAN measurements, reporting and measurement reporting event B2 in E-UTRA connected mode |
– If a category M1 UE does not support this feature group, this bit shall be set to 0 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_22_T |
Corresponding to the Index of Indicator, the leftmost binary bit 22. |
|
Support of – UTRAN FDD or UTRAN TDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports either only UTRAN FDD or only UTRAN TDD – UTRAN FDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports both UTRAN FDD and UTRAN TDD |
Yes for FDD, if UE supports UTRA FDD |
Rel-9 |
|||||
23 |
Support of – GERAN measurements, reporting and measurement reporting event B2 in E-UTRA connected mode |
– If a category M1 UE does not support this feature group, this bit shall be set to 0 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_23_T |
Corresponding to the Index of Indicator, the leftmost binary bit 23. |
|
24 |
Support of – 1xRTT measurements, reporting and measurement reporting event B2 in E-UTRA connected mode |
– If a category M1 UE does not support this feature group, this bit shall be set to 0 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_24_T |
Corresponding to the Index of Indicator, the leftmost binary bit 24. |
|
Yes, if UE supports enhanced 1xRTT CSFB |
Rel-9 |
||||||
25 |
Support of – Inter-frequency measurements and reporting in E-UTRA connected mode NOTE: The UE setting this bit to 1 and indicating support for FDD and TDD frequency bands in the UE capability signalling implements and is tested for FDD measurements while the UE is in TDD, and for TDD measurements while the UE is in FDD. |
– If a category M1 UE does not support this feature group, this bit shall be set to 0 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_25_T |
Corresponding to the Index of Indicator, the leftmost binary bit 25. |
|
Yes, unless UE only supports band 13 |
Rel-9 |
||||||
26 |
Support of – HRPD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode |
– If a category M1 UE does not support this feature group, this bit shall be set to 0 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_26_T |
Corresponding to the Index of Indicator, the leftmost binary bit 26. |
|
Yes, if UE supports HRPD |
Rel-9 |
||||||
27 |
Support of – EUTRA RRC_CONNECTED to UTRA CELL_DCH CS handover |
– related to SR-VCC – can only be set to 1 if the UE has set bit number 8 to 1 and supports SR-VCC from EUTRA defined in TS 24.008 – If a category M1 UE does not support this feature group, this bit shall be set to 0 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_27_T |
Corresponding to the Index of Indicator, the leftmost binary bit 27. Set to true if supporting all functionalities in the feature group. |
|
Support of – EUTRA RRC_CONNECTED to UTRA FDD or UTRA TDD CELL_DCH CS handover, if the UE supports either only UTRAN FDD or only UTRAN TDD – EUTRA RRC_CONNECTED to UTRA FDD CELL_DCH CS handover, if the UE supports both UTRAN FDD and UTRAN TDD |
Yes for FDD, if UE supports VoLTE and UTRA FDD |
Rel-9 |
|||||
28 |
Support of – TTI bundling |
– If a category M1 UE does not support this feature group, this bit shall be set to 0 |
Yes for FDD |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_28_T |
Corresponding to the Index of Indicator, the leftmost binary bit 28. Set to true if supporting all functionalities in the feature group. |
29 |
Support of – Semi-Persistent Scheduling |
– If a category M1 UE does not support this feature group, this bit shall be set to 0 |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_29_T |
Corresponding to the Index of Indicator, the leftmost binary bit 29. |
|
30 |
Support of – Handover between FDD and TDD |
– can only be set to 1 if the UE has set bit number 13 to 1 |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_30_T |
Corresponding to the Index of Indicator, the leftmost binary bit 30. |
|
31 |
Support of – Indicates whether the UE supports the mechanisms defined for cells broadcasting multi band information i.e. comprehending multiBandInfoList, disregarding in RRC_CONNECTED the related system information fields and understanding the EARFCN signalling for all bands, that overlap with the bands supported by the UE, and that are defined in the earliest version of TS 36.101 [42] that includes all UE supported bands. |
– In this release of the protocol, this bit will never be mandated to be set to 1 – This FGI bit concerns an optional release independent feature (as it was difficult to introduce this from REL-8 when using regular UE capability signalling) |
Rel-8 |
36.331, Annex B.1 |
pc_FeatrGrp_31_T |
Corresponding to the Index of Indicator, the leftmost binary bit 31. Set to true if supporting all functionalities in the feature group. |
|
Rel-9 |
|||||||
Yes |
Rel-10 |
||||||
32 |
Undefined |
Rel-8 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 32. |
Table A.4.4-2: Void
Table A.4.4-2a: Feature group indicators 33-64 for FDD
Item |
Additional information |
Notes |
If indicated "Yes" the feature shall be implemented and successfully tested for the corresponding release |
Release |
Ref. |
Mnemonic |
Comments |
---|---|---|---|---|---|---|---|
33 |
Inter-RAT ANR features for UTRAN including: – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI |
– can only be set to 1 if the UE has set bit number 5 and bit number 22 to 1. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_33_F |
Corresponding to the Index of Indicator, the leftmost binary bit 33. |
|
34 |
Inter-RAT ANR features for GERAN including: – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI |
– can only be set to 1 if the UE has set bit number 5 and bit number 23 to 1. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_34_F |
Corresponding to the Index of Indicator, the leftmost binary bit 34. |
|
35 |
Inter-RAT ANR features for 1xRTT including: – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI |
– can only be set to 1 if the UE has set bit number 5 and bit number 24 to 1. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_35_F |
Corresponding to the Index of Indicator, the leftmost binary bit 35. |
|
36 |
Inter-RAT ANR features for HRPD including: – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI |
– can only be set to 1 if the UE has set bit number 5 and bit number 26 to 1. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_36_F |
Corresponding to the Index of Indicator, the leftmost binary bit 36. |
|
37 |
Inter-RAT ANR features for UTRAN TDD including: – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI |
– can only be set to 1 if the UE has set bit number 5 and at least one of the bit number 22 (for UEs supporting only UTRA TDD) or the bit number 39 to 1. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_37_F |
Corresponding to the Index of Indicator, the leftmost binary bit 37. Set to true if supporting all functionalities in the feature group. |
|
38 |
-EUTRA RRC_CONNECTED to UTRA TDD CELL_DCH PS handover, if the UE supports both UTRAN FDD and UTRAN TDD |
– can only be set to 1 if the UE has set bit number 39 to 1. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_38_F |
Corresponding to the Index of Indicator, the leftmost binary bit 38. Set to true if supporting all functionalities in the feature group. |
|
39 |
-UTRAN TDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports both UTRAN FDD and UTRAN TDD |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_39_F |
Corresponding to the Index of Indicator, the leftmost binary bit 39. Set to true if supporting all functionalities in the feature group. |
|
40 |
-EUTRA RRC_CONNECTED to UTRA TDD CELL_DCH CS handover, if the UE supports both UTRAN FDD and UTRAN TDD |
– related to SR-VCC – can only be set to 1 if the UE has set bit number 38 to 1. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_40_F |
Corresponding to the Index of Indicator, the leftmost binary bit 40. Set to true if supporting all functionalities in the feature group. |
|
41 |
Measurement reporting event: Event B1 – Neighbour > threshold for UTRAN FDD, if the UE supports UTRAN FDD and has set bit number 22 to 1 |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Yes for FDD, unless UE has set bit number 15 to 1 |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_41_F |
Corresponding to the Index of Indicator, the leftmost binary bit 41. Set to true if supporting all functionalities in the feature group. |
42 |
DCI format 3a (TPC commands for PUCCH and PUSCH with single bit power adjustments) |
Rel-13 |
36.331, Annex B.1 |
pc_FeatrGrp_42_F |
Corresponding to the Index of Indicator, the leftmost binary bit 42. |
||
43 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 43. |
|||
44 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 44. |
|||
45 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 45. |
|||
46 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 46. |
|||
47 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 47. |
|||
48 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 48. |
|||
49 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 49. |
|||
50 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 50. |
|||
51 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 51. |
|||
52 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 52. |
|||
53 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 53. |
|||
54 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 54. |
|||
55 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 55. |
|||
56 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 56. |
|||
57 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 57. |
|||
58 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 58. |
|||
59 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 59. |
|||
60 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 60. |
|||
61 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 61. |
|||
62 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 62. |
|||
63 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 63. |
|||
64 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 64. |
Table A.4.4-2b: Feature group indicators 33-64 for TDD
Item |
Additional information |
Notes |
If indicated "Yes" the feature shall be implemented and successfully tested for the corresponding release |
Release |
Ref. |
Mnemonic |
Comments |
---|---|---|---|---|---|---|---|
33 |
Inter-RAT ANR features for UTRAN including: – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI |
– can only be set to 1 if the UE has set bit number 5 and bit number 22 to 1. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_33_T |
Corresponding to the Index of Indicator, the leftmost binary bit 33. |
|
34 |
Inter-RAT ANR features for GERAN including: – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCells – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI |
– can only be set to 1 if the UE has set bit number 5 and bit number 23 to 1. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_34_T |
Corresponding to the Index of Indicator, the leftmost binary bit 34. |
|
35 |
Inter-RAT ANR features for 1xRTT including: – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI |
– can only be set to 1 if the UE has set bit number 5 and bit number 24 to 1. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_35_T |
Corresponding to the Index of Indicator, the leftmost binary bit 35. |
|
36 |
Inter-RAT ANR features for HRPD including: – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI |
– can only be set to 1 if the UE has set bit number 5 and bit number 26 to 1. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_36_T |
Corresponding to the Index of Indicator, the leftmost binary bit 36. |
|
37 |
Inter-RAT ANR features for UTRAN TDD including: – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportStrongestCellsForSON – Inter-RAT periodical measurement reporting where triggerType is set to periodical and purpose is set to reportCGI |
– can only be set to 1 if the UE has set bit number 5 and at least one of the bit number 22 (for UEs supporting only UTRA TDD) or the bit number 39 to 1. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_37_T |
Corresponding to the Index of Indicator, the leftmost binary bit 37. Set to true if supporting all functionalities in the feature group. |
|
38 |
-EUTRA RRC_CONNECTED to UTRA TDD CELL_DCH PS handover, if the UE supports both UTRAN FDD and UTRAN TDD |
– can only be set to 1 if the UE has set bit number 39 to 1. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_38_T |
Corresponding to the Index of Indicator, the leftmost binary bit 38. Set to true if supporting all functionalities in the feature group. |
|
39 |
-UTRAN TDD measurements, reporting and measurement reporting event B2 in E-UTRA connected mode, if the UE supports both UTRAN FDD and UTRAN TDD |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_39_T |
Corresponding to the Index of Indicator, the leftmost binary bit 39. Set to true if supporting all functionalities in the feature group. |
|
40 |
-EUTRA RRC_CONNECTED to UTRA TDD CELL_DCH CS handover, if the UE supports both UTRAN FDD and UTRAN TDD |
– related to SR-VCC – can only be set to 1 if the UE has set bit number 38 to 1. |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_40_T |
Corresponding to the Index of Indicator, the leftmost binary bit 40. Set to true if supporting all functionalities in the feature group. |
|
41 |
Measurement reporting event: Event B1 – Neighbour > threshold for UTRAN FDD, if the UE supports UTRAN FDD and has set bit number 22 to 1 |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Yes for FDD, unless UE has set bit number 15 to 1 |
Rel-9 |
36.331, Annex B.1 |
pc_FeatrGrp_41_T |
Corresponding to the Index of Indicator, the leftmost binary bit 41. Set to true if supporting all functionalities in the feature group. |
42 |
DCI format 3a (TPC commands for PUCCH and PUSCH with single bit power adjustments) |
Rel-13 |
36.331, Annex B.1 |
pc_FeatrGrp_42_T |
Corresponding to the Index of Indicator, the leftmost binary bit 42. |
||
43 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 43. |
|||
44 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 44. |
|||
45 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 45. |
|||
46 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 46. |
|||
47 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 47. |
|||
48 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 48. |
|||
49 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 49. |
|||
50 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 50. |
|||
51 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 51. |
|||
52 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 52. |
|||
53 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 53. |
|||
54 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 54. |
|||
55 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 55. |
|||
56 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 56. |
|||
57 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 57. |
|||
58 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 58. |
|||
59 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 59. |
|||
60 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 60. |
|||
61 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 61. |
|||
62 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 62. |
|||
63 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 63. |
|||
64 |
Undefined |
Rel-9 |
36.331, Annex B.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 64. |
Table A.4.4-3: Void
Table A.4.4-3a: Feature group indicators 101-132 for FDD
Item |
Additional information |
Notes |
If indicated "Yes" the feature shall be implemented and successfully tested for the corresponding release |
Release |
Ref. |
Mnemonic |
Comments |
---|---|---|---|---|---|---|---|
101 |
– DMRS with OCC (orthogonal cover code) and SGH (sequence group hopping) disabling |
– if the UE supports two or more layers for spatial multiplexing in UL, this bit shall be set to 1. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_101_F |
Corresponding to the Index of Indicator, the leftmost binary bit 101. |
|
– If a category 0 UE does not support this feature, this bit shall be set to 0. |
Rel-12 |
||||||
102 |
– Trigger type 1 SRS (aperiodic SRS) transmission (Up to X ports) NOTE: X = number of supported layers on given band |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_102_F |
Corresponding to the Index of Indicator, the leftmost binary bit 102. |
||
103 |
– PDSCH transmission mode 9 when up to 4 CSI reference signal ports are configured |
– for Category 8 UEs, this bit shall be set to 1. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_103_F |
Corresponding to the Index of Indicator, the leftmost binary bit 103. |
|
– for Category 8 UEs, this bit shall be set to 1. – for Category 11 and higher UEs, this bit shall be set to 1. – for DL Category 11 and higher UEs (except for DL Category 13), this bit shall be set to 1. |
Yes for the UE categories listed in the column “Notes” |
Rel-15 |
|||||
104 |
– PDSCH transmission mode 9 for TDD when 8 CSI reference signal ports are configured |
– if the UE does not support TDD, this bit is irrelevant (capability signalling exists for FDD for this feature), and this bit shall be set to 0. – for Category 8 UEs, this bit shall be set to 1. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_104_F |
Corresponding to the Index of Indicator, the leftmost binary bit 104. |
|
– if the UE does not support TDD, this bit is irrelevant, and this bit shall be set to 0. – this bit is not applicable to FDD (capability signalling exists for FDD for this feature). – for Category 8 UEs, this bit shall be set to 1. – for Category 11 and higher UEs, this bit shall be set to 1. – for DL Category 11 and higher UEs (except for DL Category 13), this bit shall be set to 1. |
Yes for TDD, for the UE categories listed in the column “Notes” |
Rel-15 |
|||||
105 |
– Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-0 – UE selected subband CQI without PMI, when PDSCH transmission mode 9 is configured – Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI, when PDSCH transmission mode 9 and up to 4 CSI reference signal ports are configured |
– this bit can be set to 1 only if indices 2 (Table B.1-1) and 103 are set to 1. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_105_F |
Corresponding to the Index of Indicator, the leftmost binary bit 105. |
|
– For UEs capable of TDD-FDD CA, this bit can be set to 1 for both FDD and TDD if index 2 is set to 1 for both FDD and TDD, and index 103 is set to 1 either for FDD and TDD. |
Rel-12 |
||||||
106 |
– Periodic CQI/PMI/RI/PTI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI, when PDSCH transmission mode 9 and 8 CSI reference signal ports are configured |
– this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘ supported’) and if index 2 (Table B.1-1) is set to 1. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_106_F |
Corresponding to the Index of Indicator, the leftmost binary bit 106. |
|
– For UEs capable of TDD-FDD CA, this bit can be set to 1 for both FDD and TDD if either index 104 is set to 1 or tm9-With-8Tx-FDD-r10 is set to’ supported’, and if index 2 is set to 1 for both FDD and TDD. |
Rel-12 |
||||||
107 |
– Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-0 – UE selected subband CQI without PMI, when PDSCH transmission mode 9 is configured – Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI, when PDSCH transmission mode 9 and up to 4 CSI reference signal ports are configured |
– this bit can be set to 1 only if indices 1 (Table B.1-1) and 103 are set to 1. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_107_F |
Corresponding to the Index of Indicator, the leftmost binary bit 107. |
|
108 |
– Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI, when PDSCH transmission mode 9 and 8 CSI reference signal ports are configured |
– this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to’ supported’) and if index 1 (Table B.1-1) is set to 1. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_108_F |
Corresponding to the Index of Indicator, the leftmost binary bit 108. |
|
109 |
– Periodic CQI/PMI/RI reporting on PUCCH Mode 1-1, submode 1 |
– this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to’ supported’). |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_109_F |
Corresponding to the Index of Indicator, the leftmost binary bit 109. |
|
– For UEs capable of TDD-FDD CA, this bit can be set to 1 for both FDD and TDD if either index 104 is set to 1 or tm9-With-8Tx-FDD-r10 is set to ‘supported’. |
Rel-12 |
||||||
110 |
– Periodic CQI/PMI/RI reporting on PUCCH Mode 1-1, submode 2 |
– this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘supported’). |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_110_F |
Corresponding to the Index of Indicator, the leftmost binary bit 110. |
|
– For UEs capable of TDD-FDD CA, this bit can be set to 1 for both FDD and TDD if either index 104 is set to 1 or tm9-With-8Tx-FDD-r10 is set to ‘supported’. |
Rel-12 |
||||||
111 |
– Measurement reporting trigger Event A6 |
– this bit can be set to 1 only if the UE supports carrier aggregation. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_111_F |
Corresponding to the Index of Indicator, the leftmost binary bit 111. |
|
112 |
– SCell addition within3 the Handover to EUTRA procedure |
– this bit can be set to 1 only if the UE supports carrier aggregation and the Handover to EUTRA procedure. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_112_F |
Corresponding to the Index of Indicator, the leftmost binary bit 112. |
|
113 |
– Trigger type 0 SRS (periodic SRS) transmission on X Serving Cells NOTE: X = number of supported component carriers in a given band combination |
– this bit can be set to 1 only if the UE supports carrier aggregation in UL. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_113_F |
Corresponding to the Index of Indicator, the leftmost binary bit 113. |
|
114 |
– Reporting of both UTRA CPICH RSCP and Ec/N0 in a Measurement Report |
– this bit can be set to 1 only if index 22 (Table B.1-1) is set to 1. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_114_F |
Corresponding to the Index of Indicator, the leftmost binary bit 114. |
|
115 |
– time domain ICIC RLM/RRM measurement subframe restriction for the serving cell – time domain ICIC RRM measurement subframe restriction for neighbour cells – time domain ICIC CSI measurement subframe restriction |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_115_F |
Corresponding to the Index of Indicator, the leftmost binary bit 115. |
|
116 |
– Relative transmit phase continuity for spatial multiplexing in UL |
– this bit can be set to 1 only if the UE supports two or more layers for spatial multiplexing in UL. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_116_F |
Corresponding to the Index of Indicator, the leftmost binary bit 116. |
|
117 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 117. |
|||
118 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 118. |
|||
119 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 119. |
|||
120 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 120. |
|||
121 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 121. |
|||
122 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 122. |
|||
123 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 123. |
|||
124 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 124. |
|||
125 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 125. |
|||
126 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 126. |
|||
127 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 127. |
|||
128 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 128. |
|||
129 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 129. |
|||
130 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 130. |
|||
131 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 131. |
|||
132 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 132. |
Table A.4.4-3b: Feature group indicators 101-132 for TDD
Item |
Additional information |
Notes |
If indicated "Yes" the feature shall be implemented and successfully tested for the corresponding release |
Release |
Ref. |
Mnemonic |
Comments |
---|---|---|---|---|---|---|---|
101 |
– DMRS with OCC (orthogonal cover code) and SGH (sequence group hopping) disabling |
– if the UE supports two or more layers for spatial multiplexing in UL, this bit shall be set to 1. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_101_T |
Corresponding to the Index of Indicator, the leftmost binary bit 101. |
|
– If a category 0 UE does not support this feature, this bit shall be set to 0. |
Rel-12 |
||||||
102 |
– Trigger type 1 SRS (aperiodic SRS) transmission (Up to X ports) NOTE: X = number of supported layers on given band |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_102_T |
Corresponding to the Index of Indicator, the leftmost binary bit 102. |
||
103 |
– PDSCH transmission mode 9 when up to 4 CSI reference signal ports are configured |
– for Category 8 UEs, this bit shall be set to 1. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_103_T |
Corresponding to the Index of Indicator, the leftmost binary bit 103. |
|
– for Category 8 UEs, this bit shall be set to 1. – for Category 11 and higher UEs, this bit shall be set to 1. – for DL Category 11 and higher UEs (except for DL Category 13), this bit shall be set to 1. |
Yes for the UE categories listed in the column “Notes” |
Rel-15 |
|||||
104 |
– PDSCH transmission mode 9 for TDD when 8 CSI reference signal ports are configured |
– if the UE does not support TDD, this bit is irrelevant (capability signalling exists for FDD for this feature), and this bit shall be set to 0. – for Category 8 UEs, this bit shall be set to 1. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_104_T |
Corresponding to the Index of Indicator, the leftmost binary bit 104. |
|
– if the UE does not support TDD, this bit is irrelevant, and this bit shall be set to 0. – this bit is not applicable to FDD (capability signalling exists for FDD for this feature). – for Category 8 UEs, this bit shall be set to 1. – for Category 11 and higher UEs, this bit shall be set to 1. – for DL Category 11 and higher UEs (except for DL Category 13), this bit shall be set to 1. |
Yes for TDD, for the UE categories listed in the column “Notes” |
Rel-15 |
|||||
105 |
– Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-0 – UE selected subband CQI without PMI, when PDSCH transmission mode 9 is configured – Periodic CQI/PMI/RI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI, when PDSCH transmission mode 9 and up to 4 CSI reference signal ports are configured |
– this bit can be set to 1 only if indices 2 (Table B.1-1) and 103 are set to 1. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_105_T |
Corresponding to the Index of Indicator, the leftmost binary bit 105. |
|
– For UEs capable of TDD-FDD CA, this bit can be set to 1 for both FDD and TDD if index 2 is set to 1 for both FDD and TDD, and index 103 is set to 1 either for FDD and TDD. |
Rel-12 |
||||||
106 |
– Periodic CQI/PMI/RI/PTI reporting on PUCCH: Mode 2-1 – UE selected subband CQI with single PMI, when PDSCH transmission mode 9 and 8 CSI reference signal ports are configured |
– this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to’ supported’) and if index 2 (Table B.1-1) is set to 1. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_106_T |
Corresponding to the Index of Indicator, the leftmost binary bit 106. |
|
– For UEs capable of TDD-FDD CA, this bit can be set to 1 for both FDD and TDD if either index 104 is set to 1 or tm9-With-8Tx-FDD-r10 is set to ‘supported’, and if index 2 is set to 1 for both FDD and TDD. |
Rel-12 |
||||||
107 |
– Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-0 – UE selected subband CQI without PMI, when PDSCH transmission mode 9 is configured – Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI, when PDSCH transmission mode 9 and up to 4 CSI reference signal ports are configured |
– this bit can be set to 1 only if indices 1 (Table B.1-1) and 103 are set to 1. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_107_T |
Corresponding to the Index of Indicator, the leftmost binary bit 107. |
|
108 |
– Aperiodic CQI/PMI/RI reporting on PUSCH: Mode 2-2 – UE selected subband CQI with multiple PMI, when PDSCH transmission mode 9 and 8 CSI reference signal ports are configured |
– this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to ‘ supported’) and if index 1 (Table B.1-1) is set to 1. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_108_T |
Corresponding to the Index of Indicator, the leftmost binary bit 108. |
|
109 |
– Periodic CQI/PMI/RI reporting on PUCCH Mode 1-1, submode 1 |
– this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to’ supported’). |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_109_T |
Corresponding to the Index of Indicator, the leftmost binary bit 109. |
|
– For UEs capable of TDD-FDD CA, this bit can be set to 1 for both FDD and TDD if either index 104 is set to 1 or tm9-With-8Tx-FDD-r10 is set to ‘supported’. |
Rel-12 |
||||||
110 |
– Periodic CQI/PMI/RI reporting on PUCCH Mode 1-1, submode 2 |
– this bit can be set to 1 only if the UE supports PDSCH transmission mode 9 with 8 CSI reference signal ports (i.e., for TDD, if index 104 is set to 1, and for FDD, if tm9-With-8Tx-FDD-r10 is set to’ supported’). |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_110_T |
Corresponding to the Index of Indicator, the leftmost binary bit 110. |
|
– For UEs capable of TDD-FDD CA, this bit can be set to 1 for both FDD and TDD if either index 104 is set to 1 or tm9-With-8Tx-FDD-r10 is set to’ supported’. |
Rel-12 |
||||||
111 |
– Measurement reporting trigger Event A6 |
– this bit can be set to 1 only if the UE supports carrier aggregation. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_111_T |
Corresponding to the Index of Indicator, the leftmost binary bit 111. |
|
112 |
– SCell addition within the Handover to EUTRA procedure |
– this bit can be set to 1 only if the UE supports carrier aggregation and the Handover to EUTRA procedure. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_112_T |
Corresponding to the Index of Indicator, the leftmost binary bit 112. |
|
113 |
– Trigger type 0 SRS (periodic SRS) transmission on X Serving Cells NOTE: X = number of supported component carriers in a given band combination |
– this bit can be set to 1 only if the UE supports carrier aggregation in UL. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_113_T |
Corresponding to the Index of Indicator, the leftmost binary bit 113. |
|
114 |
– Reporting of both UTRA CPICH RSCP and Ec/N0 in a Measurement Report |
– this bit can be set to 1 only if index 22 (Table B.1-1) is set to 1. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_114_T |
Corresponding to the Index of Indicator, the leftmost binary bit 114. |
|
115 |
– time domain ICIC RLM/RRM measurement subframe restriction for the serving cell – time domain ICIC RRM measurement subframe restriction for neighbour cells – time domain ICIC CSI measurement subframe restriction |
– If a category M1 UE does not support this feature group, this bit shall be set to 0. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_115_T |
Corresponding to the Index of Indicator, the leftmost binary bit 115. |
|
116 |
– Relative transmit phase continuity for spatial multiplexing in UL |
– this bit can be set to 1 only if the UE supports two or more layers for spatial multiplexing in UL. |
Rel-10 |
36.331, Annex C.1 |
pc_FeatrGrp_116_T |
Corresponding to the Index of Indicator, the leftmost binary bit 116. |
|
117 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 117. |
|||
118 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 118. |
|||
119 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 119. |
|||
120 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 120. |
|||
121 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 121. |
|||
122 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 122. |
|||
123 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 123. |
|||
124 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 124. |
|||
125 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 125. |
|||
126 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 126. |
|||
127 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 127. |
|||
128 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 128. |
|||
129 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 129. |
|||
130 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 130. |
|||
131 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 131. |
|||
132 |
Undefined |
Rel-10 |
36.331, Annex C.1 |
Corresponding to the Index of Indicator, the leftmost binary bit 132. |