B.1 Parameter values
34.123-33GPPPart 3: Abstract test suite (ATS)TSUser Equipment (UE) conformance specification
B.1.1 BasicM test suite parameter declarations
The following parameters are common to all ATSs.
Table B.1.1: BasicM PIXIT
Parameter name |
Description |
Type |
Default value |
Supported value |
---|---|---|---|---|
px_AuthAMF |
Authentication Management Field (16 bits). The value shall be different from ‘1111 1111 1111 1111’B (AMFresynch). |
B16 |
See note 2 |
|
px_AuthK |
Authentication Key (128 bits) |
B128 |
‘01011110010010101011001101011000100100010011011101011101001010101110111010000001001011100110011111000011000010011010011000101001’B |
|
px_AuthN |
Value of n to initialize tcv_Auth_n (length of extended response) min 31, max 127 (3GPP TS 34.108 [3], clause 8.1.2) |
INTEGER |
127 |
|
px_AuthRAND |
Random Challenge (128 bits) |
BITSTRING |
‘01010101…01’B |
|
px_GPRS_CipheringAlgorithm |
Cipher algorithm |
GPRS_CipheringAlgorithm_Type |
‘010’B |
Allowed values gea0 ’000’B, gea2 ’010’B, gea3 ’011’B, gea4 ’100’B |
px_CipheringOnOff |
Security mode – TRUE if ciphering is applicable |
BOOLEAN |
TRUE |
|
px_CN_DomainTested |
CN domain to be tested. This parameter is used in test cases that handle both PS and CS domains. |
CN_DomainIdentity |
ps_domain |
|
px_DL_MaxCC_TB_bits |
Maximum sum of number of bits of all convolutionally coded transport blocks being received at an arbitrary time instant. |
MaxNoBits |
b163840 |
|
px_DL_MaxCCTrCH |
Maximum number of Simultaneous CCTrCH for downlink |
MaxSimultaneousCCTrCH_Count |
8 |
|
px_DL_MaxTB_bits |
Maximum sum of number of bits of all transport blocks being received at an arbitrary time instant. |
MaxNoBits |
b163840 |
|
px_DL_MaxTF |
Maximum number of TF for downlink |
MaxNumberOfTF |
tf1024 |
|
px_DL_MaxTFS |
Maximum number of TFC in the TFCS for downlink |
MaxNumberOfTFC_DL |
tfc1024 |
|
px_DL_MaxTrCHs |
Maximum number of simultaneous transport channels for downlink. |
MaxSimultaneousTransChsDL |
e32 |
|
px_DL_MaxTTI_TB |
Maximum total number of transport blocks received within TTIs that end within the same 10 ms interval. |
MaxTransportBlocksDL |
tb512 |
|
px_FRESH |
Value for FRESH |
Fresh |
See note 1 |
|
px_FDD_OperationBand |
Applicable for FDD The operation band under test as defined in 34.108 clause 5.1.1. |
INTEGER |
1, see note 3 |
px_UARFCN_D_Mid, px_UARFCN_D_Low and px_UARFCN_D_High shall take the values according to the value of px_FDD_OperationBand. |
px_GuardTimerExtension |
Guard timer extension value (in seconds). A reasonable value shall be used. |
INTEGER |
0 |
|
px_IMSI_Def |
Default IMSI value |
HEXSTRING |
‘001010123456063’H |
|
px_JapanMCC |
Japan MCC to be used for Band VI |
HEXSTRING |
‘442’H |
|
px_PriScrmCode |
Applicable for FDD Primary scrambling code |
PrimaryScramblingCode |
100 |
|
px_MaxAM_EntityNumberRLC_Cap |
Maximum AM Entity Number for RLC. |
MaximumAM_EntityNumberRLC_Cap |
am30 |
|
px_MaxNoDPDCH_BitsTransmitted |
Part of UL_PhysChCapabilityFDD |
MaxNoDPDCH_BitsTransmitted |
b57600 |
|
px_MaxNoDPCH_PDSCH_Codes |
Part of DL_PhysChCapabilityFDD. INTEGER (1..8). |
INTEGER |
8 |
|
px_MaxNoPhysChBitsReceived |
Part of DL_PhysChCapabilityFDD. |
MaxNoPhysChBitsReceived |
b76800 |
|
px_MaxRLC_WindowSize |
Maximum RLC window size. |
MaximumRLC_WindowSize |
mws4095 |
|
px_MS_ClsmkESIND |
default Early Sending Indication |
B1 |
‘0’B |
|
px_MS_ClsmkRevLvl |
default Revision Level |
B2 |
’10’B |
|
px_PTMSI_Def |
default PTMSI |
OCTETSTRING |
‘C2345678’O |
|
px_PTMSI_SigDef |
default PTMSI signature (3 octets, 3GPP TS 24.008 [9], clause 10.5.5.8). |
OCTETSTRING |
‘AB1234’O |
|
px_RAT |
Applicable for FDD This parameter is used to specify which radio access technology is being used for the current test execution. Valid values: fdd and tdd |
RatType |
fdd |
|
px_RRC_CS_ServTested |
CS service to be tested for RRC test cases. |
RRC_ServTested |
Speech |
|
px_RRC_PS_ServTested |
PS service to be tested for RRC test cases. |
RRC_ServTested |
ps_Interactive |
|
px_SRNC_Id |
SRNC Id |
SRNC_Identity |
‘0000 0000 0001’B |
|
px_SRNTI |
S RNTI |
S_RNTI |
‘0000 0000 0000 0000 0001’B |
|
px_TCellA |
TCell value for cell A or 1. Except for the first created cell, the value 0 applied in ts_SS_CellCfg. |
Tcell |
256 |
|
px_TCellB |
TCell value for cell B or 2. Except for the first created cell, the value 0 applied in ts_SS_CellCfg. |
Tcell |
512 |
|
px_TCellC |
TCell value for cell C or 3. Except the first created cell, the value 0 applied in ts_SS_CellCfg. |
Tcell |
1536 |
|
px_TCellD |
TCell value for cell D or 4. Except the first created cell, the value 0 applied in ts_SS_CellCfg. |
Tcell |
321 |
|
px_TCellE |
TCell value for cell E or 5. Except the first created cell, the value 0 applied in ts_SS_CellCfg. |
Tcell |
833 |
|
px_TCellF |
TCell value for cell F or 6. Except the first created cell, the value 0 applied in ts_SS_CellCfg. |
Tcell |
6577 |
|
px_TCellG |
TCell value for cell G or 7. Except the first created cell, the value 0 applied in ts_SS_CellCfg. |
Tcell |
7253 |
|
px_TCellH |
TCell value for cell H or 8. Except the first created cell, the value 0 applied in ts_SS_CellCfg. |
Tcell |
4351 |
|
px_TimerDequeuePCO |
Additional time for dequeueing PCO |
INTEGER |
5000 (ms) |
|
px_TMSI_Def |
Default TMSI |
OCTETSTRING |
‘12345678’O |
|
px_TotalRLC_AM_BufferSize |
Total RLC AM buffer size for R99. The values are according to TotalRLC-AM-BufferSize defined in 3GPP TS 25.331. |
TotalRLC_AM_BufferSize |
NA |
|
px_UARFCN_D_Mid |
Applicable for FDD Mid Range downlink UARFCN value |
INTEGER |
10700 |
|
px_UARFCN_D_Low |
Applicable for FDD Low Range downlink UARFCN value |
INTEGER |
10563 |
|
px_UARFCN_D_High |
Applicable for FDD High Range downlink UARFCN value |
INTEGER |
10837 |
|
px_UE_OpModeDef |
Default UE operation mode (either opModeA or opModeC). (For most UEs this corresponds class-A or class-C, and can not be changed by the user) |
UE_OperationMode |
opModeA |
|
px_UE_PositioningNetworkAssistedGPS_Sup |
UE positioning capability: supports the network assisted GPS |
NetworkAssistedGPS_Supported |
networkBased |
|
px_UE_PowerClass |
UE_PowerClass value of the band under test (px_FDD_OperationBand or px_TDD_OperationBand). |
UE_PowerClass |
1 |
|
px_UL_MaxCC_TB_bits |
Maximum sum of number of bits of all convolutionally coded transport blocks being transmitted at an arbitrary time instant. |
MaxNoBits |
b163840 |
|
px_UL_MaxTB_bits |
Maximum sum of number of bits of all transport blocks being transmitted at an arbitrary time instant. |
MaxNoBits |
b163840 |
|
px_UL_MaxTF |
Maximum number of TF for uplink. |
MaxNumberOfTF |
tf1024 |
|
px_UL_MaxTFS |
Maximum number of TFC in the TFCS for uplink. |
MaxNumberOfTFC_DL |
tfc1024 |
|
px_UL_MaxTrCHs |
Maximum number of simultaneous transport channels for uplink. |
MaxSimultaneousTransChsUL |
e32 |
|
px_UL_MaxTTI_TB |
Maximum total number of transport blocks transmitted within TTIs that start at the same time. |
MaxTransportBlocksUL |
tb512 |
|
px_UL_ScramblingCode |
Applicable for FDD UL scrambling code value to be used by UE. |
UL_ScramblingCode |
0 |
|
px_TDD_OperationBand |
Applicable for TDD The operation band under test as defined in 34.108 clause 5.1.2. |
INTEGER |
1 |
px_UARFCN_Mid, px_UARFCN_Low and px_UARFCN_High shall take the values according to the value of px_TDD_OperationBand. |
px_UARFCN_Mid |
Applicable for TDD Mid Range UARFCN value |
INTEGER |
9550 |
|
px_UARFCN_Low |
Applicable for TDD Low Range UARFCN value |
INTEGER |
9504 |
|
px_UARFCN_High |
Applicable for TDD High Range UARFCN value |
INTEGER |
9596 |
|
px_UARFCN_Mid_S1 |
Applicable for TDD Mid Range UARFCN value |
INTEGER |
9545 |
|
px_UARFCN_Mid_S2 |
Applicable for TDD Mid Range UARFCN value |
INTEGER |
9555 |
|
px_UARFCN_High_S1 |
Applicable for TDD High Range UARFCN value |
INTEGER |
9591 |
|
px_UARFCN_High_S2 |
Applicable for TDD High Range UARFCN value |
INTEGER |
9586 |
|
NOTE 1: No default value can be proposed (Manufacturer defined value). NOTE 2: No default value can be proposed, because not enough information is available in 3GPP TS 34.109 [4], clause 8.1.2. NOTE 3: This value shall be set in synchronization with the values that are being set for the 3 other pixits with: px_UARFCN_D_High, px_UARFCN_D_Mid, px_UARFCN_D_Low |
B.1.2 L3M test suite parameters declarations
The following parameters are commonly used in the RRC and NAS ATSs.
Table B.1.2: L3M PIXIT
Parameter name |
Description |
Type |
Default value |
Supported value |
---|---|---|---|---|
px_3G324M_MmediaEnable |
For a Multimedia UE: set to TRUE if a multimedia call is enabled; set to FALSE if a speech call is enabled. |
BOOLEAN |
TRUE |
|
px_BcapDataCompression |
Data compression supported (used in the Bearer Capability) |
B1 |
‘0’B |
|
px_BcapFNUR |
Fixed Network User rate supported: ‘00000’B: Fixed network user rate not applicable ‘00001’B: FNUR 9.6 kbit/s ‘00010’B: FNUR 14.4 kbit/s ‘00011’B: FNUR 19.2 kbit/s ‘00100’B: FNUR 28.8 kbit/s ‘00101’B: FNUR 38.4 kbit/s ‘00110’B: FNUR 48.0 kbit/s ‘00111’B: FNUR 56.0 kbit/s ‘01000’B: FNUR 64.0 kbit/s ‘01001’B: FNUR 33.6 kbit/s ‘01010’B: FNUR 32.0 kbit/s |
B5 |
‘00001’B |
|
px_BcapITC |
Information transfer capability supported (used for the generation of the Bearer Capability) 0 – UDI 1 – RDI 2 – 31 kHz Audio 3 – Other |
ItcInt |
2 |
|
px_BcapModemType |
Modem type supported (used in the Bearer Capability) |
B5 |
‘00110’B |
|
px_BcapNumberDataBits |
Number of data bits supported (used in the Bearer Capability) |
B1 |
‘1’B |
|
px_BcapNumberStopBits |
Number of Stops bits supported (used in the Bearer Capability) |
B1 |
‘1’B |
|
px_BcapOtherModemType |
Other modem type supported (used in the Bearer Capability) |
B2 |
’10’B |
|
px_BcapParity |
Parity supported (used in the Bearer Capability) |
B3 |
‘011’B |
|
px_BcapSACP |
Signalling access protocol supported (used in the Bearer Capability) |
B3 |
‘001’B |
|
px_BcapSyncAsync |
Synchronous ‘0’B or Asynchronous ‘1’B mode supported by IUT |
B1 |
‘1’B |
|
px_BcapUeFlowControl |
UE flow control. 0-outband, 1-inband, 2-no flow control. 3- X.25 4- X.75 Default: 0, outband flow control |
FlowControl |
0 |
|
px_CC_CallDiallingDigits |
Dialling digits used to initiate a CC MO call (used with the AT dial D command). |
IA5String |
"0123456902" |
|
px_CC_Serv |
Service selected for Mobile Originated calls and Mobile Terminated calls. The possible values are ("Telephony", "EmergencyCall", "31kHz", "V110", "V120", "PIAFS", "FTM", "X31", "BTM", "3G324M_Call", "Alternate Speech/Facsimile", "3G324M_SpeechPreferred") |
Services |
"31 kHz" |
|
px_DeltaSS_DelayTime |
Tdelta value (refer to 3GPP TS 34.108 [3], clause 4.2.3) in ms. |
INTEGER |
55 ms |
|
px_EmergencyCallNumber |
Emergency Number used by UE to initiate an emergency call |
IA5String |
"112" |
|
px_IMEI_Def |
Default IMEI value transmitted by UE. Digit 15 shall be set as a Spare Digit, i.e. shall be set to ‘0’ (see TS 23.003[6]). |
HEXSTRING |
See note |
|
px_IMEISV_Def |
Default IMEISV value |
HEXSTRING |
See note |
|
px_IMSI_Diff |
Different IMSI from the IMSI stored in the USIM |
HEXSTRING |
‘001010654321063’H |
|
px_SupportOpModeC |
TRUE if UE supports operation mode C, i.e. UE offers PS services only (see 3GPP TS 23.060 [60], clause 4.1 and 3GPP TS 24.008 [9]) |
BOOLEAN |
TRUE |
|
px_NwOrgPDP_Support |
This indicates if the UE implementation supports network originated PDP Context. TRUE indicates, supported FALSE indicate, not supported |
BOOLEAN |
FALSE |
|
px_PDP_IP_AddrInfoDCH |
A string parameter that identifies the MT in the address space applicable to the PDP for DCH. |
IA5String |
"200.1.1.80" |
|
px_PDP_IP_AddrInfoFACH |
A string parameter that identifies the MT in the address space applicable to the PDP for FACH. |
IA5String |
"200.1.1.90" |
|
px_PTMSI_2 |
Second PTMSI used for testing. |
OCTETSTRING |
‘C9876543’O |
|
px_PTMSI_Sig2 |
Second PTMSI signature used for testing. |
OCTETSTRING |
‘AB1234’O |
|
px_TMSI_2 |
Second TMSI value for testing |
OCTETSTRING |
‘09876543’O |
|
px_SMS_IndexOffset |
SMS index offset for the numbering of short messages, value range: (0,1) |
INTEGER |
0 |
|
NOTE: No default value can be proposed (Manufacturer defined value). |
B.1.3 NAS test suite parameters declarations
The following parameters are commonly used in the NAS ATS.
Table B.1.3: NAS PIXIT
Parameter name |
Description |
Type |
Default value |
Supported value |
---|---|---|---|---|
px_AuthRAND_2 |
A second Random Challenge (128 bits) |
BITSTRING |
‘1010101…10’B |
|
px_PTMSI_Sig3 |
Second PTMSI signature used for testing |
OCTETSTRING |
‘AB1239’O |
B.1.4 SMS test suite parameters declarations
These parameters are used in the SMS ATS.
Table B.1.4: SMS PIXIT
Parameter name |
Description |
Type |
Default value |
Supported value |
px_BMC_CB_RepPeriod01 |
CB repetition period for CB message 1 |
INTEGER |
2 |
|
px_BMC_CB_RepPeriod02 |
CB repetition period for CB message 2 |
INTEGER |
2 |
|
px_BMC_NoOfBC_Req01 |
No of broadcasts requested for CB message 1 |
INTEGER |
2 |
|
px_BMC_NoOfBC_Req02 |
No of broadcasts requested for CB message 2 |
INTEGER |
2 |
|
px_MaxCP_DataRetx |
max. number of CP data retransmissions for SMS |
INTEGER |
3 |
|
px_SMS_CB_Data01 |
Contents of the first Cell Broadcast Message sent will be converted to an OCTETSTRING |
IA5String |
"First Cell Broadcast Message" |
|
px_SMS_CB_Data02 |
Contents of the second Cell Broadcast Message sent will be converted to an OCTETSTRING |
IA5String |
"Second Cell Broadcast Message" |
|
px_SMS_CB_MsgId02 |
Message Id to be used for the second Cell Broadcast Message sent |
HEXSTRING[4] |
‘0002’H |
|
px_SMS_PrefMem1 |
SMS Preferred Memory 1 <mem1> of 3GPP TS 27.005 [22], clause 3.1 |
IA5String |
"SM" |
|
px_SMS_PrefMem2 |
SMS Preferred Memory 2 <mem2> of 3GPP TS 27.005 [22], clause 3.1 |
IA5String |
"SM" |
|
px_SMS_PrefMem3 |
SMS Preferred Memory 3 <mem3> of 3GPP TS 27.005 [22], clause 3.1 |
IA5String |
"MT" |
|
px_TC1M |
Value for timer TC1M, to be declared by the manufacturer |
INTEGER |
10000 |
B.1.5 RRC_M test suite parameters declarations
These parameters are used in the RRC and RAB ATS.
Table B.1.5: RRC and RAB PIXIT
Parameter name |
Description |
Type |
Default value |
Supported value |
---|---|---|---|---|
px_DL_MaxTC_TB_bits |
Maximum sum of number of bits of all turbo coded transport blocks being received at an arbitrary time instant. |
MaxNoBits |
b163840 |
|
px_ExecutePS_Class |
Service to be executed in RAB test cases. The allowed values are: 1: Interactive 2: BackGround 3: Streaming 0: All supported classes. Any other value is not defined. |
INTEGER |
1 |
|
px_MaxHcContextSpace |
MaxHcContextSpace if RFC 2507 [30] is supported. |
MaxHcContextSpace |
by1024 |
|
px_MaxNoSCCPCH_RL |
Part of SimultaneousSCCPCH_DPCH_Reception. |
MaxNoSCCPCH_RL |
rl1 |
|
px_PrimaryBand |
The primary operation band under test, as defined in 34.108 clause 5.1.1. Value 1 means Band 1, 2 means Band 2, 3 means Band 3, 6 means Band 6. |
INTEGER |
1 |
This pixit shall be set in synchronization with the values that are being set to other Pixit: px_UARFCN_D_Mid |
px_SecondaryBand |
The secondary operation band under test, as defined in 34.108 clause 5.1.1. Value 1 means Band 1, 2 means Band 2, 3 means Band 3, 6 means Band 6. |
INTEGER |
8 |
|
px_SMS_CB_MsgId01 |
the operator shall define the CB Message ID for the CB data1 used for transmitting this CB data, different to CB-Data 2 IXIT |
HEXSTRING[4] |
‘0001’H |
|
px_SMS_CB_Store |
TRUE if Broadcast Messages are kept in BM storage |
BOOLEAN |
TRUE |
|
px_SMS_MsgFrmt |
SMS Message Format <mode> of TS 27.005 cl. 3.2.3 |
IA5String |
"1" |
Default “Text mode” NOTE: Change value to “0” to execute tests with PDU mode. |
px_SMS_PrefMemCB1 |
SMS Preferred CB Memory 1 <mem1> of 3GPP TS 27.005 [22], clause 3.1 |
IA5String |
"BM" |
|
px_SMS_PrefMemCB2 |
SMS Preferred CB Memory 2 <mem2> of 3GPP TS 27.005 [22], clause 3.1 |
IA5String |
"BM" |
|
px_SMS_PrefMemCB3 |
SMS Preferred CB Memory 3 <mem3> of 3GPP TS 27.005 [22], clause 3.1 |
IA5String |
"BM" |
|
px_SMS_Service |
SMS Service <service> of 3GPP TS 27.005 [22], clause 3.2.1 |
IA5String |
"0" |
|
px_UL_MaxTC_TB_bits |
Maximum sum of number of bits of all turbo coded transport blocks being transmitted at an arbitrary time instant. |
MaxNoBits |
b163840 |
The px_ExecutePS_Class allows the option 0 to be selected. This has been allowed in order to preserve the changes implemented in TTCN for handling all traffic classes in RAB testcase execution. System simulators are not required to support this execution and also TTCN maintenance of this path should be limited.
B.1.6 PDCP test suite parameters declarations
These parameters are used in the PDCP ATS.
Table B.1.6: PDCP PIXIT
Parameter name |
Description |
Type |
Default value |
Supported value |
---|---|---|---|---|
px_PDCP_TcpIpCompressedTcpNonDeltaPacket01 |
IP header compressed packet type (PID=3) of px_PDCP_TcpIpUncompressedPacket01 |
IP_Packet |
0000 0000 0000 0a00 0000 0050 1000 0026 3400 006a 6e6e 206a 6e6e 206a 6e6e |
|
px_PDCP_TcpIpCompressedTcpNonDeltaPacket02 |
IP header compressed packet type (PID=3) of px_PDCP_TcpIpUncompressedPacket02 |
IP_Packet |
"Test_PDCP_TCPIP_Packet2_PID_Type3" |
|
px_PDCP_TcpIpCompressedTcpPacket01 |
IP header compressed packet type (PID=2) of px_PDCP_TcpIpUncompressedPacket01 |
IP_Packet |
0028 2634 0a00 0000 6a6e 6e20 6a6e 6e |
|
px_PDCP_TcpIpCompressedTcpPacket02 |
IP header compressed packet type (PID=2) of px_PDCP_TcpIpUncompressedPacket02 |
IP_Packet |
"Test_PDCP_TCPIP_Packet2_PID_Type2" |
|
px_PDCP_TcpIpFullHeaderPacket01 |
IP header compressed packet type (PID=1) of px_PDCP_TcpIpUncompressedPacket01 |
IP_Packet |
c500 0000 0000 0000 4006 7ac6 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 5010 0000 263e 0000 6a6e 6e20 6a6e 6e |
|
px_PDCP_TcpIpFullHeaderPacket02 |
IP header compressed packet type (PID=1) of px_PDCP_TcpIpUncompressedPacket02 |
IP_Packet |
"Test_PDCP_TCPIP_Packet2_PID_Type1" |
|
px_PDCP_TcpIpUncompressedPacket01 |
uncompressed TCP/IP Packet01 |
IP_Packet |
4500 0033 0000 0000 4006 7ac6 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 5010 0000 263e 0000 6a6e 6e20 6a6e 6e |
|
px_PDCP_TcpIpUncompressedPacket02 |
uncompressed TCP/IP Packet02 |
IP_Packet |
"Test_PDCP_TCPIP_Packet2" |
|
px_PDCP_UdpIpCompressedTcpNonTcpPacket01 |
IP header compressed packet type (PID=4) of px_PDCP_UdpIpUncompressedPacket01 |
IP_Packet |
0001 0000 763c 6a6e 6e20 6a6e 6e20 6a6e 6e |
|
px_PDCP_UdpIpCompressedTcpNonTcpPacket02 |
IP header compressed packet type (PID=4) of px_PDCP_UdpIpUncompressedPacket02 |
IP_Packet |
"Test_PDCP_UDPIP_Packet2_PID_Type4" |
|
px_PDCP_UdpIpFullHeaderPacket01 |
IP header compressed packet type (PID=1) of px_PDCP_UdpIpUncompressedPacket01 |
IP_Packet |
8500 0100 0000 0000 4011 7ac7 0000 0000 0000 0000 0000 0000 0013 763c 6a6e 6e20 6a6e 6e20 6a6e 6e |
|
px_PDCP_UdpIpFullHeaderPacket02 |
IP header compressed packet type (PID=1) of px_PDCP_UdpIpUncompressedPacket02 |
IP_Packet |
"Test_PDCP_UDPIP_Packet2_PID_Type1" |
|
px_PDCP_UdpIpUncompressedPacket01 |
uncompressed UDP/IP Packet01 |
IP_Packet |
4500 0027 0000 0000 4011 7ac7 0000 0000 0000 0000 0000 0000 0013 763c 6a6e 6e20 6a6e 6e20 6a6e 6e |
|
px_PDCP_UdpIpUncompressedPacket02 |
uncompressed UDP/IP Packet02 |
IP_Packet |
"Test_PDCP_UDPIP_Packet2" |
B.1.7 BMC test suite parameters declarations
These parameters are used in the BMC ATS.
Table B.1.7: BMC PIXIT
Parameter name |
Description |
Type |
Default value |
Supported value |
px_CB_Data1 |
Data to be sent for each PDCP test, except TC 7.4.1.4, 7.4.1.5 and 7.4.1.6 |
IA5String [1..1246] |
"CB Data1" |
|
px_CB_Data2 |
Data to be sent in TC 7.4.2.1 |
IA5String [1..1246] |
"CB Data2" |
|
px_SMS_CB_MsgId01 |
Data to be sent for each PDCP test, except TC 7.4.1.4, 7.4.1.5 and 7.4.1.6 |
HEXSTRING[4] |
‘0000’H |
|
px_SMS_CB_MsgId02 |
Data to be sent in TC 7.4.2.1 |
HEXSTRING[4] |
‘0000’H |
|
px_gS01 |
Data to be sent for each PDCP test, except TC 7.4.1.4, 7.4.1.5 and 7.4.1.6 |
BITSTRING[2] |
"Test_gS1" |
|
px_ggS02 |
Data to be sent in TC 7.4.2.1 |
BITSTRING[2] |
"Test_gS2" |
|
px_MsgCode01 |
Data to be sent for each PDCP test, except TC 7.4.1.4, 7.4.1.5 and 7.4.1.6 |
BITSTRING[10] |
"Test_msgCode01" |
|
px_MsgCode02 |
Data to be sent in TC 7.4.2.1 |
BITSTRING[10] |
"Test_msgCode02" |
|
px_UpdateNumber01 |
Data to be sent for each PDCP test, except TC 7.4.1.4, 7.4.1.5 and 7.4.1.6 |
BITSTRING[4] |
"Test_ updateNumber01" |
|
px_UpdateNumber02 |
Data to be sent in TC 7.4.2.1 |
BITSTRING[4] |
"Test_ updateNumber02" |
B.1.8 RRC test suite parameters declarations
These parameters are used in the RRC ATS.
Table B.1.8: RRC PIXIT
Parameter name |
Description |
Type |
Default value |
Supported value |
---|---|---|---|---|
– |
– |
– |
– |
– |
B.1.9 RAB test suite parameters declarations
These parameters are used in the RAB ATS.
Table B.1.9: RAB PIXIT
Parameter Name |
Description |
Type |
Default Value |
Supported Value |
---|---|---|---|---|
px_CB_Data1 |
the operator shall define CBS data as IA5String together with the CB message ID used for transmitting this CB data, which is indicated by the UE after reception in a clear way according to the capabilities stored on the SIM. Furthermore, the operator shall describe the indication on the UE side (e.g. certain CBS traffic information) |
IA5String_BMC |
the CB data range is 1..1246 Octets which refers to a IA5String of 1..1246 |
|
px_DSCH_RNTI |
DSCH RNTI |
DSCH_RNTI |
‘0000 0000 0000 0010’B |
|
px_gS01 |
used in the Serial No. of the CB_Data01 given as PIXIT, which differentiates between CBS messages from the same source and type |
B2 |
’00’B |
|
px_MsgCode01 |
used in the Serial No. of the CB_Data01 given as PIXIT, which is the Geographical Scope indicates the area over which the msg code is unique |
MsgCodeType |
‘0000000000’B |
|
px_UpdateNumber01 |
used in the Serial No. of the CB_Data01 given as PIXIT, which indicates a change of the message content of the same CBS message |
B4 |
‘0000’B |
|
px_PowerDSCH |
transmission power level of DSCH |
DL_TxPower |
||
px_RAB_ExecImplctTestedTC |
TRUE enforces execution of optional lower bit rate R99 RAB combination test cases that are implicitly tested in higher bit rate RAB combination test cases |
BOOLEAN |
FALSE |
B.1.10 RLC and MAC test suite parameters declarations
These parameters are used in the MAC ATS.
Table B.1.10: RLC & MAC PIXIT
Parameter Name |
Description |
Type |
Default Value |
Supported Value |
px_NumOfSegInPagResOrServReq |
This Pixit is used in MAC test cases 7.1.1.2, 7.1.1.3, 7.1.1.4, 7.1.1.5 and 7.1.1.8 This indicates the number of RLC segments the Paging Response (CS Domain) or Service Request (PS domain) will be segmented in. |
INTEGER |
2 |
|
px_RLC_SDU_buffering |
Is used in RLC TC 7.2.3.13, indicating the way to handle RLC SDU data for UL transmission when the transmission window is full |
BOOLEAN(TRUE for buffering, FALSE for discard) |
B.1.11 Multi RAT test suite parameters declarations
These parameters are used in the MultiRAT ATS.
Table B.1.11: MultiRAT PIXIT
Parameter name |
Description |
Type |
Default value |
Supported value |
---|---|---|---|---|
px_ExtDTM_EGPRS_MultiSlotClass |
Extended DTM GPRS Multi Slot Class. Used in Classmark 3 |
B2 |
||
px_GSM_BandUnderTest |
indicates which band is under test |
INTEGER |
1 -> GSM450; 2 -> GSM480; 3 -> GSM750; 4 -> GSM850; 5 -> GSM-P-900; 6-> GSM-E-900; 7-> DCS1800; 8 -> PCS1900; 9 -> 450 & 900 MultiBand test; 10 -> 450 & 1800 MultiBand test; 11 -> 480 & 900 MultiBand test; 12 -> 480 & 1800 MultiBand test; 13 -> 900 & 1800 MultiBand test; 14-> GSM710; 15->T-GSM810; |
|
px_GSM_CipheringOnOff |
GSM Ciphering to be started or not |
B1 |
1 |
|
px_GSM_CipherAlg |
GSM Cipher algorithm. |
B3_CipherAlg |
‘000’B |
Allowed values: ‘000’B(A5/1), ‘010’B(A5/3), ‘011’B(A5/4) |
px_HighMultiSlotCap |
High Multislot Capability. Used in Classmark 3 |
B2 |
||
px_CipherKey |
Cipher key (64 bits) |
B64 |
‘0101111001001010101100110101100010010001001101110101110100101010’B |
Any |
px_CipherKey128 |
Cipher key (128 bits) to be used e.g. for A5/4 and GEA/4 |
B128 |
‘01011110010010101011001101011000100100010011011101011101001010100101111001001010101100110101100010010001001101110101110100101010’B |
Any |
px_MS_TXPWR_MAX_CCH |
MS_TXPWR_MAX_CCH |
B5 |
‘01010’B |
|
px_RXLEV_ACCESS_MIN |
minimum received signal level at MS |
B6 |
‘000000’B |
|
px_SplitOnCCCH |
split paging cycle on CCCH supported indication |
B1 |
‘0’B not supported |
|
px_TSC |
Training sequence code for traffic channels |
B3 |
‘011’B |
|
px_PowerLevel |
power level value for L1 header |
B5 |
||
px_TimingAdvance |
Timing advance value for L1 header |
B1 |
‘0000000’B |
B.1.12 MMI questions
Table B.1.12 requests additional information needed for the execution of the MMI commands used in the ATSs, the column ‘ATS’ indicates in which ATS the question is used.
Table B.1.12: MMI questions
Required information for MMI question |
ATS |
---|---|
Please switch the PLMN selection mode of the UE to automatic selection |
RRC, SMS, NAS, RAB, HSD_ENH, IR_U, AGPS, HSU_ENH, HS_ENH |
Please switch the PLMN selection mode of the UE to manual selection |
RRC, SMS, NAS, RAB, HSD_ENH, IR_U, AGPS, HSU_ENH, HS_ENH |
Please select the following PLMN manually: MCC = <p_MCC>, MNC = <p_MNC> |
RRC, SMS, NAS, RAB HSD_ENH, IR_U, AGPS, HSU_ENH, HS_ENH |
Please power off the UE |
All ATSs |
Please power on the UE |
All ATSs |
Please switch off the UE |
All ATSs |
Please switch on the UE |
All ATSs |
Please insert the USIM card into the UE |
All ATSs |
Please remove the USIM card into the UE |
All ATSs |
Please check that the DTCH is through connected by generating a noise |
RRC, SMS, NAS, RAB, HSD_ENH, IR_U, AGPS, HSU_ENH |
Configure UE for an MO Telephony call |
RRC, SMS, NAS, RAB, HSD_ENH, IR_U, AGPS, HSU_ENH, HS_ENH |
Configure UE for an Emergency call |
RRC, SMS, NAS, RAB, HSD_ENH, IR_U, AGPS, HSU_ENH, HS_ENH |
Configure UE for an MT telephony call |
RRC, SMS, NAS, RAB, HSD_ENH, IR_U, AGPS, HSU_ENH, HS_ENH |
Please set UE in operation mode C (PS services only) |
RRC, SMS, NAS, RAB, HSD_ENH, IR_U, AGPS, HSU_ENH, HS_ENH |
Please set UE in operation mode A (to support simultaneous CS and PS services) |
RRC, SMS, NAS, RAB, HSD_ENH, IR_U, AGPS, HSU_ENH, HS_ENH |
Please configure UE to use the following emergency number <p_EmergencyNumber> |
RRC, SMS, NAS, RAB, HSD_ENH, IR_U, A-GPS, HSU_ENH, HS_ENH |
Please initiate a non call related supplementary service which is supported by the UE |
NAS |
Please insert Test USIM programmed with Access Class: <p_AccessClass> |
NAS |
Please insert 2nd SIM card with short IMSI |
NAS, SMS, AGPS |
Please initiate an autocalling call with the number: <p_AutocallingNumber> |
NAS |
Please initiate an autocalling call with a number that will be put in the blacklisted list. The following number shall not be used: <p_AutocallingNumber> |
NAS |
Please reset the autocalling list of blacklisted numbers |
NAS |
Please initiate a DTMF tone with the character <p_Character> and the tone duration <p_ToneDuration> |
NAS |
Please enable call refusal on the UE |
NAS |
Please check that the DTMF tone indication has been generated |
NAS |
Please insert another USIM card as required for test case tc_9_4_5_4_6. The PLMN selector on the USIM card shall contain entries for PLMNs MCC=’022’H, MNC=’01F’H resp. MCC=’022’H , MNC=’03F’H. The latter PLMN shall be ranked better than the first one |
NAS |
Please trigger UE to initiate a Detach procedure for non-PS services only |
NAS |
Please check that the mobile indicates the reception of a message with message id: <p_MessageId > and message code: <p_MessageCode> |
SMS |
Please check the length of the received Short Message: <p_LengthMessage> and the contents of the received Short Message: <p_Message> |
SMS |
Please send an SMS COMMAND message containing a request to delete the previously submitted Short Message |
SMS |
Please send an SMS COMMAND message containing an enquiry about the previously submitted Short Message |
SMS |
Please check that NO recalled Short Message is displayed |
SMS |
Please check that the reception of a received Short Message is indicated |
SMS |
Please check that the Mobile does not indicate the reception of a new message with message id: <p_MessageId> and message code: <p_MessageCode> |
SMS |
Please check that NO reception of a received Short Message of type 0 is indicated |
SMS |
Please insert the USIM card of type B into the UE |
MAC |
Please insert the USIM card, with information given in <p_TestCase> |
RRC, NAS, IR_U, HSU_ENH, HS_ENH |
Please check that the UE display the registered PLMN as PLMN <p_PLMN> |
RRC, HSU_ENH, HS_ENH |
Please insert the USIM card, with Type A EFACC |
RRC |
Please insert the USIM card, with Type B EFACC |
RRC |
Please trigger UE to send three SNDCP PDUs of 500 bytes each on SAPI 11 |
IR_G |
Please trigger PDP Context Activation Type 2 in UE |
IR_G |
Please trigger MO-LR for position estimate |
AGPS |
Please trigger MO-LR for assistance data |
AGPS |
Please trigger MO-LR for transfer to 3rd party |
AGPS |
Please check that the UE displays the correct information about the LCS client |
AGPS |
Please accept the location request within 20 s |
AGPS |
Please deny the location request within 20 s |
AGPS |
Please do not reply to the location request |
AGPS |
Please check that the UE notifies the user of the location request |
AGPS |
If the UE does not support the RESET command defined in 34.109, please ensure that the UE has no assistance data stored before running this test case |
AGPS |
Please trigger UE to send 10 kbytes of data on SAPI 3 |
IR_G |
Please trigger UE to send 1 kbyte of data on SAPI 3 |
IR_G |
Please check that in the manual PLMN list the UE display: <p_PLMN_List> |
HSU_ENH |
Please check that UE displays no service or no network available |
HSU_ENH, HSPA8_ENH |
Please check that in the manual PLMN list the UE displays the PLMN with the following information: – <p_PLMN_List1> offers voice call, SMS and PS data services – <p_PLMN_List2> offers voice call services – <p_PLMN_List3> offers PS data services |
HS_ENH |
Please check that in the manual PLMN list the UE indicates that: – <p_PLMN1> is present on the the User Controlled PLMN List – <p_PLMN2> is present on the Forbidden list – <p_PLMN3> is present on the Operator Controlled PLMN List |
HS_ENH |
Please insert the USIM card with an empty CSG allowed list |
HSPA8_ENH |
Please switch the PLMN selection mode of the UE to manual CSG selection |
HSPA8_ENH |
Please switch the PLMN selection mode of the UE to automatic CSG selection |
HSPA8_ENH |
Please select the following CSG manually: MCC = <p_MCC>, MNC = <p_MNC>, CSG = <p_CSG> |
HSPA8_ENH |
Please check that in the manual CSG list the UE display: <p_CSG1> accessible, <p_CSG2> not accessible |
HSPA8_ENH |
Please check that the Mobile UE indicates the reception of ETWS data <p_ETWS_Data> and alerts or activate alerting the user. |
HSPA8_ENH |
Please check that the Mobile UE does NOT indicate the reception of ETWS data <p_ETWS_Data> and not alert, nor activate alerting the user |
HSPA8_ENH |
Please set the PLMN selection operation mode at switch on in the UE to automatic network selection |
HSPA7_ENH |
Please set the PLMN selection operation mode at switch on in the UE to manual network selection |
HSPA7_ENH |
B.1.13 A-GPS test suite parameters declarations
These parameters are used in the A-GPS ATS.
Table B.1.13: A-GPS PIXIT
Parameter Name |
Description |
Type |
Default Value |
Supported Value |
---|---|---|---|---|
px_GpsScenario |
Pre-defined GPS scenario to be loaded by the upper tester in the Satellite Simulator. See 3GPP TS 34.108 [3], clause 10.7. Minimum value:0, Maximum value: 31 |
GpsScenarioType |
0 |
|
px_GeoInfo |
Geographical information to be sent as Location Estimate in FACILITY message from the System Simulator. |
Ext_GeographicalInformation |
9032B9D66360B600323C3C006544 |
|
px_LcsClientName |
LCS Client name |
IA5String |
OPERATOR |
|
px_LcsClientAddressTOA |
LCS Client external address TOA |
B4 |
‘1001’B |
|
px_LcsClientAddressNPI |
LCS Client external address NPI |
B4 |
‘0001’B |
|
px_LcsClientAddressDigits |
LCS Client external address Digits |
IA5String |
0123456 |
|
px_ResetStoredInfo |
Support of RESETUEPOSITIONINGSTOREDINFORMATION command as defined in 3GPP TS 34.109 [4], clause 6.10 |
BOOLEAN |
TRUE |
|
px_UeLcsNotification |
Value for UE LCS Notification timeout timer (in seconds) |
INTEGER |
20 |
B.1.14 HSD_ENH test suite parameters declarations
These parameters are used in the HSD_ENH ATS.
Table B.1.14: HSD_ENH PIXIT
Parameter Name |
Description |
Type |
Default Value |
Supported Value |
---|---|---|---|---|
px_GERANIu_RadioAccessCapability |
MS GERAN Iu mode Radio Access Capability |
BITSTRING |
||
px_RAB_HS_Exec128_384Supp |
TRUE enforces execution of optional UL 128 Kbps RAB HSDPA test cases, when UE supports UL384 Kbps |
BOOLEAN |
FALSE |
|
px_RAB_HS_Exec64_384Supp |
TRUE enforces execution of optional UL 64 Kbps RAB HSDPA test cases, when UE supports UL 384 kbps |
BOOLEAN |
FALSE |
|
px_RAB_HS_Exec64_128Supp |
TRUE enforces execution of optional UL 64 Kbps RAB HSDPA test cases, when UE supports UL128 kbps |
BOOLEAN |
FALSE |
|
px_CMAS_CB_Data01 |
Contents of the first CMAS Cell Broadcast Message of 90 characters. |
IA5String |
"First CMAS message: CMAS Presidential Alert. ABCDEFGHIJKLMNOPQRSTUVWXYZ123456890abcdefghijklmnopqrst" |
|
px_CMAS_CB_Data02 |
Contents of the second CMAS Cell Broadcast Message of 90 characters. |
IA5String |
"Second CMAS message: CMAS Imminent Threat Alert – Severity: Extreme, Urgency: Immediate. ABCDEFGHIJ” |
|
px_CMAS_CB_Data03 |
Contents of the third CMAS Cell Broadcast Message of 90 characters. |
IA5String |
"Third CMAS message: CMAS Child Abduction Emergency. ABCDEFGHIJKLMNOPQRSTUVWXYZ123456890abcdefghijklm" |
B.1.15 HSU_ENH test suite parameters declarations
These parameters are used in the HSU_ENH ATS.
Table B.1.15: HSU_ENH PIXIT
Parameter Name |
Description |
Type |
Default Value |
Supported Value |
---|---|---|---|---|
px_ExecNon_FDPCH_When_FDPCHSupp |
To execute Non-FDPCH test case when fully FDPCH is supported |
BOOLEAN |
TRUE |
B.1.16 HS_ENH test suite parameters declarations
These parameters are used in the HS_ENH ATS.
Table B.1.16: HS_ENH PIXIT
Parameter Name |
Description |
Type |
Default Value |
Supported Value |
---|---|---|---|---|
Void |
B.1.17 Audit capabilities test suite parameters declarations
These parameters are used in the audit capabilities test case.
Table B.1.17.1: UTRA audit capabilities PIXIT
Parameter Name |
Description |
Type |
Default Value |
Supported Value |
---|---|---|---|---|
px_MaxNumberROHC_ContextSessions |
Maximum number of ROHC context sessions, see 3GPP TS 25.331 [21], clause 10.3.3.24 |
MaxROHC_ContextSessions_r4 |
||
px_ReverseDecompressionDepth |
Reverse decompression depth, see 3GPP TS 25.331 [21], clause 10.3.3.24 |
INTEGER |
Table B.1.17.2: GERAN audit capabilities PIXIT
Parameter Name |
Description |
Type |
Default Value |
Supported Value |
---|---|---|---|---|
px_8PSK_PowerCap |
Radio Capability used for 8PSK modulation, see 3GPP TS 24.008 [9], clause 10.5.5.12a |
B2 |
||
px_Alt_EFTA_MultislotClass |
Alternative Enhanced Flexible Timeslot Assignment Multislot Class, see 3GPP TS 24.008 [9], clause 10.5.5.12a |
B4 |
||
px_EGPRS_MultislotClass |
Integer representation of the multislot class, see 3GPP TS 24.008 [9], clause 10.5.5.12a |
INTEGER |
||
px_GERAN_to_EUTRA_Support |
GERAN to E-UTRA support in GERAN packet transfer mode, see 3GPP TS 24.008 [9], clause 10.5.5.12a |
B2 |
||
px_GMSK_PowerCap |
Power Class used for GMSK with the indicated Access Technology, see 3GPP TS 24.008 [9], clause 10.5.5.12a |
B3 |
||
px_GPRS_MultislotClass |
Integer representation of the multislot class, see 3GPP TS 24.008 [9], clause 10.5.5.12a |
INTEGER |
||
px_Multislot_Capability_Reduction_for_Downlink_Dual_Carrier |
Multislot Capability Reduction for Downlink Dual Carrier, see 3GPP TS 24.008 [9], clause 10.5.5.12a |
B3 |
Table B.1.17.3: E-UTRA audit capabilities PIXIT
Parameter Name |
Description |
Type |
Default Value |
Supported Value |
---|---|---|---|---|
px_eMaxNumberROHC_ContextSessions |
Maximum number of ROHC context sessions |
maxNumberROHC_ContextSessions_Type |
||
px_InterFreqMeasBandList_eBand1 |
Indicates need for measurement gaps when operating on the E‑UTRA band 1 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand2 |
Indicates need for measurement gaps when operating on the E‑UTRA band 2 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand3 |
Indicates need for measurement gaps when operating on the E‑UTRA band 3 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand4 |
Indicates need for measurement gaps when operating on the E‑UTRA band 4 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand5 |
Indicates need for measurement gaps when operating on the E‑UTRA band 5 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand6 |
Indicates need for measurement gaps when operating on the E‑UTRA band 6 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand7 |
Indicates need for measurement gaps when operating on the E‑UTRA band 7 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand8 |
Indicates need for measurement gaps when operating on the E‑UTRA band 8 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand9 |
Indicates need for measurement gaps when operating on the E‑UTRA band 9 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand10 |
Indicates need for measurement gaps when operating on the E‑UTRA band 10 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand11 |
Indicates need for measurement gaps when operating on the E‑UTRA band 11 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand12 |
Indicates need for measurement gaps when operating on the E‑UTRA band 12 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand13 |
Indicates need for measurement gaps when operating on the E‑UTRA band 13 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand14 |
Indicates need for measurement gaps when operating on the E‑UTRA band 14 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand17 |
Indicates need for measurement gaps when operating on the E‑UTRA band 17 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand18 |
Indicates need for measurement gaps when operating on the E‑UTRA band 18 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand19 |
Indicates need for measurement gaps when operating on the E‑UTRA band 19 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand20 |
Indicates need for measurement gaps when operating on the E‑UTRA band 20 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterFreqMeasBandList_eBand21 |
Indicates need for measurement gaps when operating on the E‑UTRA band 21 and measuring other supported E‑UTRA bands. |
InterFreqBandList |
||
px_InterRAT_MeasBandList_eBand1 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 1 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand2 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 2 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand3 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 3 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand4 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 4 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand5 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 5 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand6 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 6 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand7 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 7 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand8 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 8 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand9 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 9 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand10 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 10 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand11 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 11 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand12 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 12 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand13 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 13 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand14 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 14 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand17 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 17 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand18 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 18 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand19 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 19 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand20 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 20 and measuring other supported inter-RAT bands |
interRAT_BandList |
||
px_InterRAT_MeasBandList_eBand21 |
Indicates need for DL measurement gaps when operating on the E‑UTRA band 21 and measuring other supported inter-RAT bands |
interRAT_BandList |
B.1.18 eCall and HSPA8 test suite parameters declarations
These parameters are used in the eCall and HSPA8 ATS.
Table B.1.18: eCall and HSPA8 PIXIT
Parameter Name |
Description |
Type |
Default Value |
Supported Value |
---|---|---|---|---|
px_eCall_TestNumber |
Number digits of the test number used in eCall Test Call. Numbers are in the order: Digit 1, Digit 2, Digit 3, etc (see 3GPP TS 24.008 [9], clause 10.5.4.7) |
IA5String |
"123456" |
|
px_eCall_ReconfNumber |
Number digits of the reconfiguration number used in eCall Reconfiguration Call. Numbers are in the order: Digit 1, Digit 2, Digit 3, etc (see 3GPP TS 24.008 [9], clause 10.5.4.7) |
IA5String |
"987654" |
|
px_ETWS_BMC_CB_RepPeriod |
CB repetition period for ETWS CB message |
INTEGER |
2 |
|
px_ETWS_BMC_NoOfBC_Req |
No of broadcasts requested for ETWS CB message |
INTEGER |
2 |
|
px_ETWS_SMS_CB_Data01 |
Contents of the first ETWS Cell Broadcast Message sent will be converted to an OCTETSTRING |
IA5String_BMC |
"First ETWS Cell Broadcast Message" |
|
px_ETWS_SMS_CB_Data02 |
Contents of the second ETWS Cell Broadcast Message sent will be converted to an OCTETSTRING |
IA5String_BMC |
"Second ETWS Cell Broadcast Message" |
|
px_ETWS_SMS_CB_Data03 |
Contents of the third ETWS Cell Broadcast Message sent will be converted to an OCTETSTRING |
IA5String_BMC |
"Third ETWS Cell Broadcast Message" |
|
px_ETWS_SMS_CB_Data04 |
Contents of the fourth ETWS Cell Broadcast Message sent will be converted to an OCTETSTRING |
IA5String_BMC |
"Fourth ETWS Cell Broadcast Message" |
|
px_ETWS_SMS_CB_Data05 |
Contents of the fifth ETWS Cell Broadcast Message sent will be converted to an OCTETSTRING |
IA5String_BMC |
"Fifth ETWS Cell Broadcast Message" |
|
px_ETWS_SMS_CB_Data06 |
Contents of the sixth ETWS Cell Broadcast Message sent will be converted to an OCTETSTRING |
IA5String_BMC |
"Sixth ETWS Cell Broadcast Message" |
|
px_ETWS_TimeZone |
Value of the Time Zone in ETWS cell broadcast message |
TZONES |
0 |
B.1.19 IR_U test suite parameters declarations
These parameters are used in the IR_U ATS.
Table B.1.19: IR_U PIXIT
Parameter Name |
Description |
Type |
Default Value |
Supported Value |
---|---|---|---|---|
px_ITURegion1_GSM_BandsUnderTest |
Indicates the GSM band under test for ITU region 1 |
ITURegion1_GSM_BandsUnderTest |
||
px_ITURegion2_GSM_BandsUnderTest |
Indicates the GSM band under test for ITU region 2 |
ITURegion2_GSM_BandsUnderTest |
||
px_ITURegion1_SecondaryFDD_Band |
Indicates the secondary FDD band under test for ITU region 1 |
ITURegion1_FDD_Band |
||
px_ITURegion2_SecondaryFDD_Band |
Indicates the secondary FDD band under test for ITU region 2 |
ITURegion2_FDD_Band |
B.1.20 TTCN-3 test suite parameters declarations
These parameters are used in the TTCN-3 test suites.
Table B.1.20: TTCN-3 PIXIT
Parameter Name |
Description |
Type |
Default Value |
Supported Value |
---|---|---|---|---|
px_AnrForUtranMeasLogWaitTime |
Time required by UE to measure, detect and log an ANR cell in idle mode, CELL_PCH and URA_PCH. Value in seconds in the range of 1 to 60 seconds |
integer |
15 s |
Annex C (informative):
Additional information to IXIT
Notwithstanding the provisions of the copyright related to the text of the present document, The Organizational Partners of 3GPP grant that users of the present document may freely reproduce the IXIT proforma in this annex so that it can be used for its intended purposes and may further publish the completed IXIT.
Additional information may be provided when completing the IXIT questions listed in annex A.