6.4 WLAN Environment

34.123-13GPPPart 1: Protocol conformance specificationRelease 15TSUser Equipment (UE) conformance specification

6.4.1 WLAN Offload / Cell Selection / UTRA RRC_Idle to/from WLAN (Qrxlevmeas, BeaconRSSI)

6.4.1.1 Definition

6.4.1.2 Conformance requirement

1. The UE is in UTRA RRC_IDLE state, and UE receives SystemInformationBlockType23 including RAN-assisted WLAN interworking data and configured with ThreshServingOffloadWLAN, Low and ThreshBeaconRSSIWLAN, High. When the UE measures that Serving cell has condition: Qrxlevmeas < ThreshServingOffloadWLAN, Low and the target WLAN AP has condition: BeaconRSSI > ThreshBeaconRSSIWLAN, High, the UE initiates handover attach to WLAN after TsteeringWLAN.

2. The UE is associated with WLAN AP and attached to WLAN ePDG and configured with ThreshBeaconRSSIWLAN, Low and ThreshServingOffloadWLAN, High. When the UE measures that WLAN AP has condition: BeaconRSSI < ThreshBeaconRSSIWLAN, Low and UTRA Serving cell has condition: Qrxlevmeas < ThreshServingOffloadWLAN, High, the UE initiates handover attach to WLAN cell after TsteeringWLAN.

The rules in this sub-clause are only applicable for WLANs for which identifiers have been signalled to the UE by UTRAN and the UE is capable of access network selection and traffic steering rules. Coexistence with ANDSF based WLAN selection and traffic steering methods on the UE is based on mechanism described in TS 23.402 [23]. The rules refer to the following WLAN quantities:

ChannelUtilizationWLAN

WLAN channel utilization as defined in sub-clause 8.4.2.30 in [24].

BackhaulRateDlWLAN

WLAN DLBandwidth as defined in sub-clause 9.1.2 in [25].

BackhaulRateUlWLAN

WLAN ULBandwidth as defined sub-clause 9.1.2 in [25].

BeaconRSSI

WLAN Beacon RSSI as defined in [26] and [27].

Reference

1. TS 25.304, clause 5.10.2

6.4.1.3 Test purpose

1. To verify that a UE initiates handover attach to WLAN after TsteeringWLAN when Serving cell has condition: Qrxlevmeas < ThreshServingOffloadWLAN, Low and the target WLAN AP has condition: BeaconRSSI > ThreshBeaconRSSIWLAN, High.

2. To verify that a UE initiates handover attach to UTRA cell after TsteeringWLAN WLAN AP has condition: BeaconRSSI < ThreshBeaconRSSIWLAN, Low and UTRA Serving cell has condition: Qrxlevmeas < ThreshServingOffloadWLAN, High.

6.4.1.4 Method of test

Initial conditions

– Cell 1 and Cell 39 are configured. Cell 39 is switched off.

– System information configuration 11 as defined in TS 34.108 [18] clause 6.1.0a.2 is used in Cell 1.

– The UE is in PS+PS-DCCH+DTCH_Idle State 6-19 as specified in clause 7.4 of TS 34.108on Cell 1.

Step a-c:

Parameter

Unit

Cell 1

(UTRAN)

Test Channel

1

CPICH_Ec (FDD)

dBm / 3.84 MHz

-71

P-CCPCH_RSCP (TDD)

dBm

-71

Parameter

Unit

Cell 39

(WLAN)

BeaconRSSI

dBm

68

Step d-e:

Parameter

Unit

Cell 39

(WLAN)

BeaconRSSI

dBm

45

Test Procedure

a) The SS activates Cell 39.

b) Wait for TsteeringWLAN.

c) The SS waits to see if the UE offloads to the WLAN AP after TsteeringWLAN as described in Clause C.6.1.

d) Wait for TsteeringWLAN.

e) The SS waits to see if the UE offloads to the UTRA Cell after TsteeringWLAN as described in Clause C.6.2.

6.4.1.5 Test Requirements

1) In Step c), UE shall offload the PDN to Cell 39.

2) In Step e), UE shall offload the PDN to Cell 1.

Specific Message Contents

The reference system configuration from TS 34.108 clause 6.1 is used in Cell 1, with the following modification:

SYSTEM INFORMATION BLOCK TYPE 23

Information Element

Condition

Value/remark

– CHOICE WLAN representation

WLAN Offload Information common for all PLMN

– WLAN Offload Information

– WLAN Offload Configuration

-Threshold Serving RSCP

RSCP

-ThreshservingOffloadWLAN, low

-65 dBm

-ThreshservingOffloadWLAN, high

-62 dBm

-Threshold Serving Ec/N0

Ec/No

Not Present

-Threshold Channel Utilization

ChannelUtilization

Not Present

-Threshold Backhaul Bandwidth

BackHaul

-Threshold Beacon RSSI

– ThreshBeaconRSSIWLAN, low

50 (value in dBm =-78)

ThreshBeaconRSSIWLAN, high

60(value in dBm =-68)

-TsteeringWLAN

7 seconds

6.4.2 WLAN Offload / Cell Selection / UTRA RRC_Idle to/from WLAN (Qrxlevmeas, BackhaulRateDlWLAN, WLAN identifier no match/match)

6.4.2.1 Definition

Test to Verify UE offload from UTRA RRC_Idle to WLAN when Qrxlevmeas  < ThreshServingOffloadWLAN, Low and BackhaulRateDlWLAN > ThreshBackhRateDLWLAN, High and

Verify UE offload from WLAN to UTRA RRC_Idle when BackhaulRateDlWLAN < ThreshBackhRateDLWLAN, Low and Qrxlevmeas  < ThreshServingOffloadWLAN, High.

Verify that the UE does not offload by Cell Selection from UTRA RRC_IDLE to WLAN when the WLAN Identifier does not match the identifier broadcast in SIB23.

6.4.2.2 Conformance requirement

The rules in this sub-clause are only applicable for WLANs for which identifiers have been signalled to the UE by UTRAN and the UE is capable of access network selection and traffic steering rules. Coexistence with ANDSF based WLAN selection and traffic steering methods on the UE is based on mechanism described in TS 23.402 [23]. The rules refer to the following WLAN quantities:

ChannelUtilizationWLAN

WLAN channel utilization as defined in sub-clause 8.4.2.30 in [24].

BackhaulRateDlWLAN

WLAN DLBandwidth as defined in sub-clause 9.1.2 in [25].

BackhaulRateUlWLAN

WLAN ULBandwidth as defined sub-clause 9.1.2 in [25].

BeaconRSSI

WLAN Beacon RSSI as defined in [26] and [27].

The upper layers in the UE shall be notified (see TS 24.302 [28]) when and for which WLAN(s), that matches all the provided identifiers (in sub-clause 5.10.3) for a specific entry in the list, the following conditions 1 and 2 for steering traffic from UTRAN to WLAN are satisfied for a time interval TsteeringWLAN:

1. In the UTRAN serving cell:

Qrxlevmeas < ThreshServingOffloadWLAN, Low; or

Qqualmeas < ThreshServingOffloadWLAN, Low2.

2. In the target WLAN:

ChannelUtilizationWLAN < ThreshChUtilWLAN, Low; and

BackhaulRateDlWLAN > ThreshBackhRateDLWLAN, High; and

BackhaulRateUlWLAN > ThreshBackhRateULWLAN, High; and

BeaconRSSI > ThreshBeaconRSSIWLAN, High.

The UE shall not consider the metrics for which a threshold has not been provided. The UE shall evaluate the UTRAN conditions on the serving cell in Idle mode, URA_PCH, CELL_PCH, CELL_FACH and CELL_DCH. If not all metrics related to the provided thresholds can be acquired for a WLAN BSS, the UE shall exclude that WLAN BSS from the evaluation of the above rule.

The upper layers in the UE shall be notified (see TS 24.302 [28]) when the following conditions 3 or 4 for steering traffic from WLAN to UTRAN are satisfied for a time interval TsteeringWLAN:

1. In the source WLAN:

ChannelUtilizationWLAN > ThreshChUtilWLAN, High; or

BackhaulRateDlWLAN < ThreshBackhRateDLWLAN, Low; or

BackhaulRateUlWLAN < ThreshBackhRateULWLAN, Low; or

BeaconRSSI < ThreshBeaconRSSIWLAN, Low.

2. In the target UTRANcell:

Qrxlevmeas > ThreshServingOffloadWLAN, High; and

Qqualmeas > ThreshServingOffloadWLAN, High2.

The UE shall not consider the metrics for which a threshold has not been provided. The UE shall evaluate the UTRAN conditions on the serving cell in Idle mode, URA_PCH, CELL_PCH, CELL_FACH and CELL_DCH.

Reference

1. TS 25.304, clause 5.10.2

6.4.2.3 Test purpose

To test the behaviour of the UE idle mode offload to/from WLAN

  1. UTRA RRC_Idle to WLAN when Qrxlevmeas  < ThreshServingOffloadWLAN, Low and BackhaulRateDlWLAN > ThreshBackhRateDLWLAN, High
  2. WLAN to UTRA RRC_Idle when BackhaulRateDlWLAN < ThreshBackhRateDLWLAN, Low and Qrxlevmeas  < ThreshServingOffloadWLAN, High

6.4.2.4 Method of test

Initial condition

– Cell 1 and Cell 39 are configured. Cell 39 is switched off.

– System information configuration 11 as defined in TS 34.108 [18] clause 6.1.0a.2 is used in Cell 1.

– UE is in PS+PS-DCCH+DTCH_Idle State 6-19 as specified in clause 7.4 of TS 34.108on Cell 1.

Step a-c:

Parameter

Unit

Cell 1

(UTRAN)

Test Channel

1

CPICH_Ec (FDD)

dBm / 3.84 MHz

-71

P-CCPCH_RSCP (TDD)

dBm

-71

Parameter

Unit

Cell 39

(WLAN AP)

BackhaulRateDlWLAN

kbps

r16384

BackhaulRateUlWLAN

kbps

r8192

Step c

Parameter

Unit

Cell 1

(UTRAN)

WLAN SSID

Value same as that of cell 39

CPICH_Ec (FDD)

dBm / 3.84 MHz

-60

P-CCPCH_RSCP (TDD)

dBm

-60

Step d-e

Parameter

Unit

Cell 1

(UTRAN)

CPICH_Ec (FDD)

dBm / 3.84 MHz

-71

P-CCPCH_RSCP (TDD)

dBm

-71

Step f-g

Parameter

Unit

Cell 39

(WLAN AP)

2BackhaulRateDlWLAN

kbps

r2048

Test procedure

Method C is applied.

a) The SS activates Cell 39.

b) Wait for TsteeringWLAN

c) Update system information to transmit WLAN identifier matching to that of cell 39 and wait for 5 seconds to allow UE to read the system information.

d) Wait for TsteeringWLAN

e) SS checks if the test result of generic test procedure in TS 34.123-1 sub clause C.6.1 indicates that the PDN connection is offloaded from UTRAN to WLAN

f) Wait for TsteeringWLAN

g) SS checks if the test result of generic test procedure in TS 34.123-1 sub clause C.6.2 indicates that the PDN connection is offloaded from WLAN to UTRAN.

6.4.2.5 Test requirements

1) In Step b), UE shall not offload the PDN to Cell 39 after TsteeringWLAN.

2) In Step e), UE shall offload the PDN to Cell 39.

3) In Step g), UE shall offload the PDN to Cell 1

Specific Message Contents

The reference system configuration from TS 34.108 clause 6.1 is used in Cell 1, with the following modification:

SYSTEM INFORMATION BLOCK TYPE 23 (Preamble)

Information Element

Condition

Value/remark

– CHOICE WLAN representation

WLAN Offload Information common for all PLMN

– WLAN Offload Information

– WLAN Offload Configuration

-Threshold Serving RSCP

RSCP

-ThreshservingOffloadWLAN, low

-65 dBm

-ThreshservingOffloadWLAN, high

-62 dBm

-Threshold Serving Ec/N0

Ec/No

Not Present

-Threshold Channel Utilization

ChannelUtilization

Not Present

-Threshold Backhaul Bandwidth

BackHaul

-ThreshbackhRateDLWLAN, low

[r4096] kbps

-ThreshbackhRateDLWLAN, high

[r8192] kbps

-ThreshbackhRateULWLAN, low

[r0] kbps: Value makes it insignificant for offload

-ThreshbackhRateULWLAN, high

[r4294967296] kbps: Value makes it insignificant for offload

-Threshold Beacon RSSI

RSSI

Not Present

-TsteeringWLAN

7 seconds

-WLAN Identifier List

Only 1 WLAN identifier broadcasted

– WLAN Identifier

– WLAN Type ID

-SSID

Any value Different from that of Cell 39

SYSTEM INFORMATION BLOCK TYPE 23 (Step c and later)

Information Element

Condition

Value/remark

– CHOICE WLAN representation

WLAN Offload Information common for all PLMN

– WLAN Offload Information

– WLAN Offload Configuration

-Threshold Serving RSCP

RSCP

-ThreshservingOffloadWLAN, low

-65 dBm

-ThreshservingOffloadWLAN, high

-62 dBm

-Threshold Serving Ec/N0

Ec/No

Not Present

-Threshold Channel Utilization

ChannelUtilization

Not Present

-Threshold Backhaul Bandwidth

BackHaul

-ThreshbackhRateDLWLAN, low

r4096 kbps

-ThreshbackhRateDLWLAN, high

r8192 kbps

-ThreshbackhRateULWLAN, low

r0 kbps : Value makes it insignificant for offload

-ThreshbackhRateULWLAN, high

r4294967296 kbps : Value makes it insignificant for offload

-Threshold Beacon RSSI

RSSI

Not Present

-TsteeringWLAN

7 seconds

-WLAN Identifier List

Only 1 WLAN identifier broadcasted

– WLAN Identifier

– WLAN Type ID

-SSID

Value same as that of Cell 39

6.4.3 WLAN Offload / Cell Selection / UTRA RRC_Idle to/from WLAN (Qrxlevmeas, BackhaulRateUlWLAN)

6.4.3.1 Definition

Test to Verify UE offload from UTRA RRC_Idle to WLAN when Qrxlevmeas  < ThreshServingOffloadWLAN, Low and BackhaulRateUlWLAN > ThreshBackhRateULWLAN, High and

Verify UE offload from WLAN to UTRA RRC_Idle when BackhaulRateUlWLAN < ThreshBackhRateULWLAN, Low and Qrxlevmeas  < ThreshServingOffloadWLAN, High.

          1. Conformance requirement

The rules in this sub-clause are only applicable for WLANs for which identifiers have been signalled to the UE by UTRAN and the UE is capable of access network selection and traffic steering rules. Coexistence with ANDSF based WLAN selection and traffic steering methods on the UE is based on mechanism described in TS 23.402 [23]. The rules refer to the following WLAN quantities:

ChannelUtilizationWLAN

WLAN channel utilization as defined in sub-clause 8.4.2.30 in [24].

BackhaulRateDlWLAN

WLAN DLBandwidth as defined in sub-clause 9.1.2 in [25].

BackhaulRateUlWLAN

WLAN ULBandwidth as defined sub-clause 9.1.2 in [25].

BeaconRSSI

WLAN Beacon RSSI as defined in [26] and [27].

The upper layers in the UE shall be notified (see TS 24.302 [28]) when and for which WLAN(s), that matches all the provided identifiers (in sub-clause 5.10.3) for a specific entry in the list, the following conditions 1 and 2 for steering traffic from UTRAN to WLAN are satisfied for a time interval TsteeringWLAN:

1. In the UTRAN serving cell:

Qrxlevmeas < ThreshServingOffloadWLAN, Low; or

Qqualmeas < ThreshServingOffloadWLAN, Low2.

2. In the target WLAN:

ChannelUtilizationWLAN < ThreshChUtilWLAN, Low; and

BackhaulRateDlWLAN > ThreshBackhRateDLWLAN, High; and

BackhaulRateUlWLAN > ThreshBackhRateULWLAN, High; and

BeaconRSSI > ThreshBeaconRSSIWLAN, High.

The UE shall not consider the metrics for which a threshold has not been provided. The UE shall evaluate the UTRAN conditions on the serving cell in Idle mode, URA_PCH, CELL_PCH, CELL_FACH and CELL_DCH. If not all metrics related to the provided thresholds can be acquired for a WLAN BSS, the UE shall exclude that WLAN BSS from the evaluation of the above rule.

The upper layers in the UE shall be notified (see TS 24.302 [28]) when the following conditions 3 or 4 for steering traffic from WLAN to UTRAN are satisfied for a time interval TsteeringWLAN:

1. In the source WLAN:

ChannelUtilizationWLAN > ThreshChUtilWLAN, High; or

BackhaulRateDlWLAN < ThreshBackhRateDLWLAN, Low; or

BackhaulRateUlWLAN < ThreshBackhRateULWLAN, Low; or

BeaconRSSI < ThreshBeaconRSSIWLAN, Low.

2. In the target UTRANcell:

Qrxlevmeas > ThreshServingOffloadWLAN, High; and

Qqualmeas > ThreshServingOffloadWLAN, High2.

The UE shall not consider the metrics for which a threshold has not been provided. The UE shall evaluate the UTRAN conditions on the serving cell in Idle mode, URA_PCH, CELL_PCH, CELL_FACH and CELL_DCH.

Reference

1. TS 25.304, clause 5.10.2

6.4.3.3 Test purpose

To test the behaviour of the UE idle mode offload to/from WLAN:

1. UTRA RRC_Idle to WLAN when Qrxlevmeas  < ThreshServingOffloadWLAN, Low and BackhaulRateUlWLAN > ThreshBackhRateULWLAN, High

2. WLAN to UTRA RRC_Idle when BackhaulRateUlWLAN < ThreshBackhRateULWLAN, Low and Qrxlevmeas  < ThreshServingOffloadWLAN, High

6.4.3.4 Method of test

Initial condition

– Cell 1 and Cell 39 are configured. Cell 39 is switched off.

– System information configuration 11 as defined in TS 34.108 [18] clause 6.1.0a.2 is used in Cell 1.

– UE is in PS+PS-DCCH+DTCH_Idle State 6-19 as specified in clause 7.4 of TS 34.108on Cell 1.

Step a-c:

Parameter

Unit

Cell 1

(UTRAN)

Test Channel

1

CPICH_Ec (FDD)

dBm / 3.84 MHz

-71

P-CCPCH_RSCP (TDD)

dBm

-71

Parameter

Unit

Cell 39

(WLAN AP)

BackhaulRateDlWLAN

kbps

r8192

BackhaulRateUlWLAN

kbps

r16384

Step d-e

Parameter

Unit

Cell 39

(WLAN AP)

BackhaulRateUlWLAN

kbps

r2048

Test procedure

Method C is applied.

a) The SS activates Cell 39

b) Wait for TsteeringWLAN

c) SS checks if the test result of generic test procedure in TS 34.123-1 sub clause C.6.1 indicates that the PDN connection is offloaded from UTRAN to WLAN

d) Wait for TsteeringWLAN

e) SS checks if the test result of generic test procedure in TS 34.123-1 sub clause C.6.2 indicates that the PDN connection is offloaded from WLAN to UTRAN

6.4.3.5 Test requirements

1) In Step c), UE shall offload the PDN to Cell 39.

2) In Step e), UE shall offload the PDN to Cell 1.

Specific Message Contents

The reference system configuration from TS 34.108 clause 6.1 is used in Cell 1, with the following modification:

SYSTEM INFORMATION BLOCK TYPE 23

Information Element

Condition

Value/remark

– CHOICE WLAN representation

WLAN Offload Information common for all PLMN

– WLAN Offload Information

– WLAN Offload Configuration

-Threshold Serving RSCP

RSCP

-ThreshservingOffloadWLAN, low

-65 dBm

-ThreshservingOffloadWLAN, high

-62 dBm

-Threshold Serving Ec/N0

Ec/No

Not Present

-Threshold Channel Utilization

ChannelUtilization

Not Present

-Threshold Backhaul Bandwidth

BackHaul

-ThreshbackhRateDLWLAN, low

[r0] kbps : Value makes it insignificant for offload

-ThreshbackhRateDLWLAN, high

[r4294967296] kbps : Value makes it insignificant for offload

-ThreshbackhRateULWLAN, low

[r4096] kbps

-ThreshbackhRateULWLAN, high

[r8192] kbps

-Threshold Beacon RSSI

RSSI

Not Present

-TsteeringWLAN

7 seconds

6.4.4 WLAN Offload / Cell Selection / UTRA RRC_Idle to/from WLAN (Qqualmeas, ChannelUtilizationWLAN)

6.4.4.1 Definition

6.4.4.2 Conformance requirement

1. The UE is in UTRA RRC_IDLE state, and UE receives SystemInformationBlockType23 including RAN-assisted WLAN interworking data and configured with ThreshServingOffloadWLAN, Low and ThreshChUtilWLAN, Low. When the UE measures that Serving cell has condition: Qqualmeas < ThreshServingOffloadWLAN, Low and the target WLAN AP has condition: ChannelUtilizationWLAN < ThreshChUtilWLAN, High, the UE initiates handover attach to WLAN after TsteeringWLAN.

2. The UE is associated with WLAN AP and attached to WLAN ePDG and configured with ThreshChUtilWLAN, High and ThreshServingOffloadWLAN, High. When the UE measures that WLAN AP has condition: ChannelUtilizationWLAN > ThreshChUtilWLAN, High and UTRA Serving cell has condition: Qqualmeas < ThreshServingOffloadWLAN, High, the UE initiates handover attach to WLAN cell after TsteeringWLAN.

The rules in this sub-clause are only applicable for WLANs for which identifiers have been signalled to the UE by UTRAN and the UE is capable of access network selection and traffic steering rules. Coexistence with ANDSF based WLAN selection and traffic steering methods on the UE is based on mechanism described in TS 23.402 [23]. The rules refer to the following WLAN quantities:

ChannelUtilizationWLAN

WLAN channel utilization as defined in sub-clause 8.4.2.30 in [24]

BackhaulRateDlWLAN

WLAN DLBandwidth as defined in sub-clause 9.1.2 in [25]

BackhaulRateUlWLAN

WLAN ULBandwidth as defined sub-clause 9.1.2 in [25]

BeaconRSSI

WLAN Beacon RSSI as defined in [26] and [27]

Reference

1. TS 25.304, clause5.10.2

6.4.4.3 Test purpose

1. To verify that a UE initiates handover attach to WLAN after TsteeringWLAN when Serving cell has condition: Qqualmeas < ThreshServingOffloadWLAN, Low and the target WLAN AP has condition: ChannelUtilizationWLAN < ThreshChUtilWLAN, High.

2. To verify that a UE initiates handover attach to UTRA cell after TsteeringWLAN WLAN AP has condition: ChannelUtilizationWLAN > ThreshChUtilWLAN, High and UTRA Serving cell has condition: Qqualmeas < ThreshServingOffloadWLAN, High.

6.4.4.4 Method of test

Initial conditions

– Cell 1 and Cell 39 are configured. Cell 39 is switched off.

– System information configuration 11 as defined in TS 34.108 [18] clause 6.1.0a.2 is used in Cell 1.

– The UE is in PS+PS-DCCH+DTCH_Idle State 6-19 as specified in clause 7.4 of TS 34.108on Cell 1.

Step a-c:

Parameter

Unit

Cell 1

UTRA RF Channel Number

Mid Range Test Frequency

CPICH Ec

dBm/3.84MHz

-75

Ioc (Noise)

dBm/3.84MHz

-60

CPICH_Ec/No

dB

-15.65

Parameter

Unit

Cell 39

UTRA RF Channel Number

Mid Range Test Frequency

ChannelUtilizationWLAN

40

Step d-e:

Parameter

Unit

Cell 1

UTRA RF Channel Number

Mid Range Test Frequency

CPICH Ec

dBm/3.84MHz

-60

Ioc (Noise)

dBm/3.84MHz

-60

CPICH_Ec/No

dB

-7.87

Parameter

Unit

Cell 39

UTRA RF Channel Number

Mid Range Test Frequency

ChannelUtilizationWLAN

100

Test Procedure

a) The SS activates Cell 39.

b) Wait for TsteeringWLAN.

c) The SS waits to see if the UE offloads to the WLAN AP after TsteeringWLAN as described in Clause C.6.1.

d) Wait for TsteeringWLAN.

e) The SS waits to see if the UE offloads to the UTRA Cell after TsteeringWLAN as described in Clause C.6.2.

6.4.4.5 Test Requirements

1) In Step c), UE shall offload the PDN to Cell 39.

2) In Step e), UE shall offload the PDN to Cell 1.

Specific Message Contents

The reference system configuration from TS 34.108 clause 6.1 is used in Cell 1, with the following modification:

SYSTEM INFORMATION BLOCK TYPE 23

Information Element

Condition

Value/remark

– CHOICE WLAN representation

WLAN Offload Information common for all PLMN

– WLAN Offload Information

– WLAN Offload Configuration

-Threshold Serving RSCP

RSCP

-Threshold Serving Ec/N0

Ec/No

-ThreshservingOffloadWLAN, low2

-11 dBm

-ThreshservingOffloadWLAN, high2

-11 dBm

-Threshold Channel Utilization, Low

50

-Threshold Channel Utilization, High

80

-TsteeringWLAN

7 seconds

6.4.5 Void