14.6.4 Conversational / unknown / UL:64 DL:64 kbps / CS RAB + Interactive or background / UL:384 DL:[Bit rate depending on the UE category] / PS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH
34.123-13GPPPart 1: Protocol conformance specificationRelease 15TSUser Equipment (UE) conformance specification
14.6.4.1 Conformance requirement
See 14.6.1.1.
14.6.4.2 Test purpose
To verify radio bearer establishment and correct data transfer for reference radio bearer configuration as specified in TS 34.108, clause 6.10.2.4.5.4.
14.6.4.3 Method of test
NOTE: The reference to UE Categories refers to the UE capability as signalled in the Rel-5 IE “HS-DSCH physical layer category” (1 to 12). All UEs supporting HS-DSCH should signal a category between 1 and 12 for this IE even if the UE physical capability category is above 12. This IE corresponds to the HS-DSCH category supported by the UE when MAC-ehs is not configured.
Initial Conditions
The following RLC Info parameter values shall be set by the SS for the Conversational / unknown / UL:64 DL:64 kbps / CS RAB (RB5):
|
RB5 (Conv. 64 kbps) |
|
|
Uplink RLC |
|
|
TM RLC |
|
|
Segmentation indication |
FALSE |
|
Transmission RLC discard |
|
|
CHOICE SDU Discard Mode |
|
|
Timer based no explicit |
|
|
Timer_discard |
100ms |
|
Downlink RLC |
|
|
TM RLC |
|
|
Segmentation indication |
FALSE |
|
NOTE: Timer based discard without explicit signalling is used in uplink to secure that the UE will be able to return data for the case when the UE test loop function will not deliver all the SDUs in one and the same TTI . |
|
The generic test procedure in 14.1.3.5 is run for each sub-test.
Uplink TFS:
|
TFI |
RB5 (Conv. 64 kbps, 20 ms TTI) |
RB6 (I/B 384 kbps, 10 ms TTI) |
DCCH |
|
|
TFS |
TF0, bits |
0x640 |
0x336 |
0x148 |
|
TF1, bits |
2×640 |
1×336 |
1×148 |
|
|
TF2, bits |
N/A |
2×336 |
N/A |
|
|
TF3, bits |
N/A |
4×336 |
N/A |
|
|
TF4, bits |
N/A |
8×336 |
N/A |
|
|
TF5, bits |
N/A |
12×336 |
N/A |
Uplink TFCS:
|
TFCI |
(RB5, RB6, DCCH) |
|
UL_TFC0 |
(TF0,TF0,TF0) |
|
UL_TFC1 |
(TF1,TF0,TF0) |
|
UL_TFC2 |
(TF0,TF1,TF0) |
|
UL_TFC3 |
(TF1,TF1,TF0) |
|
UL_TFC4 |
(TF0,TF2,TF0) |
|
UL_TFC5 |
(TF1,TF2,TF0) |
|
UL_TFC6 |
(TF0,TF3,TF0) |
|
UL_TFC7 |
(TF1,TF3,TF0) |
|
UL_TFC8 |
(TF0,TF4,TF0) |
|
UL_TFC9 |
(TF1,TF4,TF0) |
|
UL_TFC10 |
(TF0,TF5,TF0) |
|
UL_TFC11 |
(TF1,TF5,TF0) |
|
UL_TFC12 |
(TF0,TF0,TF1) |
|
UL_TFC13 |
(TF1,TF0,TF1) |
|
UL_TFC14 |
(TF0,TF1,TF1) |
|
UL_TFC15 |
(TF1,TF1,TF1) |
|
UL_TFC16 |
(TF0,TF2,TF1) |
|
UL_TFC17 |
(TF1,TF2,TF1) |
|
UL_TFC18 |
(TF0,TF3,TF1) |
|
UL_TFC19 |
(TF1,TF3,TF1) |
|
UL_TFC20 |
(TF0,TF4,TF1) |
|
UL_TFC21 |
(TF1,TF4,TF1) |
|
UL_TFC22 |
(TF0,TF5,TF1) |
|
UL_TFC23 |
(TF1,TF5,TF1) |
Downlink TFS:
|
TFI |
RB5 (Conv. 64 kbps, 20 ms TTI) |
DCCH |
|
|
TFS |
TF0, bits |
0x640 |
0x148 |
|
TF1, bits |
2×640 |
1×148 |
Downlink TFCS:
|
TFCI |
(RB5, DCCH) |
|---|---|
|
DL_TFC0 |
(TF0, TF0) |
|
DL_TFC1 |
(TF1, TF0) |
|
DL_TFC2 |
(TF0, TF1) |
|
DL_TFC3 |
(TF1, TF1) |
Sub-tests:
The principle used to select sub-tests has been to cover all uplink and downlink TFS for the Conversational CS and Interactive Background PS radio bearer. As the Interactive Background UL:384 kbps radio bearer (RB6) has the highest number of transport formats (5 for TTI=10 ms and excluding TF0) then 5 sub-tests have been defined. The selected UL TFCI to achieve test coverage of TF1 to TF5 for RB6 and for TF1 for RB5 is: UL_TFC3 for TF1, UL_TFC5 for TF2, UL_TFC7 for TF3, UL_TFC9 for TF4 and UL_TFC11 for TF5.
|
Sub-tes |
UE Category |
Number of HARQ processes |
RLC Receiving window size (note 1) |
RLC Trans-mission window size (note 1) |
MAC-d PDU size (bits) |
Downlink TFCS Under test |
Uplink TFCS Under test |
Implicitly tested |
Restricted UL TFCIs (note 2) |
UL RLC SDU size (bits) (note 3) |
Test data size (bits) (note 4) |
|---|---|---|---|---|---|---|---|---|---|---|---|
|
1 |
1 |
2 |
512 |
256 |
336 |
DL_TFC1 |
UL_TFC3 |
DL_TFC0, DL_TFC2, UL_TFC0, UL_TFC12 |
UL_TFC0, UL_TFC1, UL_TFC2, UL_TFC3, UL_TFC12, UL_TFC15 |
RB5: 640 RB6: 312 |
RB5: 2×640 RB6: See note 4 |
|
2 |
2 |
512 |
256 |
||||||||
|
3 |
3 |
512 |
256 |
||||||||
|
4 |
3 |
512 |
256 |
||||||||
|
5 |
6 |
512 |
256 |
||||||||
|
6 |
6 |
512 |
256 |
||||||||
|
7 |
6 |
1536 |
512 |
||||||||
|
8 |
6 |
1536 |
512 |
||||||||
|
9 |
6 |
2047 |
512 |
||||||||
|
10 |
5 |
2047 |
512 |
||||||||
|
11 |
3 |
512 |
256 |
||||||||
|
12 |
6 |
512 |
256 |
||||||||
|
2 |
1 |
2 |
256 |
256 |
656 |
DL_TFC1 |
UL_TFC5 |
DL_TFC0, DL_TFC2, UL_TFC0, UL_TFC12 |
UL_TFC0, UL_TFC1, UL_TFC2, UL_TFC5, UL_TFC12, UL_TFC17 |
RB5: 640 RB6: 632 |
RB5: 2×640 RB6: See note 4 |
|
2 |
2 |
256 |
256 |
||||||||
|
3 |
3 |
256 |
256 |
||||||||
|
4 |
3 |
256 |
256 |
||||||||
|
5 |
6 |
256 |
256 |
||||||||
|
6 |
6 |
256 |
256 |
||||||||
|
7 |
6 |
512 |
512 |
||||||||
|
8 |
6 |
512 |
512 |
||||||||
|
9 |
6 |
1024 |
512 |
||||||||
|
10 |
5 |
1024 |
1024 |
||||||||
|
11 |
3 |
256 |
256 |
||||||||
|
12 |
6 |
256 |
256 |
||||||||
|
3 |
1 |
2 |
512 |
256 |
336 |
DL_TFC1 |
UL_TFC7 |
DL_TFC0, DL_TFC2, UL_TFC0, UL_TFC12 |
UL_TFC0, UL_TFC1, UL_TFC2, UL_TFC7, UL_TFC12, UL_TFC19 |
RB5: 640 RB6: 1272 |
RB5: 2×640 RB6: See note 4 |
|
2 |
2 |
512 |
256 |
||||||||
|
3 |
3 |
512 |
256 |
||||||||
|
4 |
3 |
512 |
256 |
||||||||
|
5 |
6 |
512 |
256 |
||||||||
|
6 |
8 |
512 |
256 |
||||||||
|
7 |
8 |
1536 |
512 |
||||||||
|
8 |
8 |
1536 |
512 |
||||||||
|
9 |
8 |
2047 |
512 |
||||||||
|
10 |
5 |
2047 |
1024 |
||||||||
|
11 |
3 |
512 |
256 |
||||||||
|
12 |
8 |
512 |
256 |
||||||||
|
4 |
1 |
2 |
256 |
256 |
656 |
DL_TFC1 |
UL_TFC9 |
DL_TFC0, DL_TFC2, UL_TFC0, UL_TFC12 |
UL_TFC0, UL_TFC1, UL_TFC2, UL_TFC9, UL_TFC12, UL_TFC21 |
RB5: 640 RB6: 2552 |
RB5: 2×640 RB6: See note 4 |
|
2 |
2 |
256 |
256 |
||||||||
|
3 |
3 |
256 |
256 |
||||||||
|
4 |
3 |
256 |
256 |
||||||||
|
5 |
6 |
256 |
256 |
||||||||
|
6 |
8 |
256 |
256 |
||||||||
|
7 |
8 |
512 |
512 |
||||||||
|
8 |
8 |
512 |
512 |
||||||||
|
9 |
8 |
1024 |
512 |
||||||||
|
10 |
5 |
1024 |
1024 |
||||||||
|
11 |
3 |
256 |
256 |
||||||||
|
12 |
8 |
256 |
256 |
||||||||
|
5 |
1 |
2 |
256 |
256 |
656 |
DL_TFC1 |
UL_TFC11 |
DL_TFC0, DL_TFC2, UL_TFC0, UL_TFC12 |
UL_TFC0, UL_TFC1, UL_TFC2, UL_TFC11, UL_TFC12, UL_TFC23 |
RB5: 640 RB6: 3832 |
RB5: 2×640 RB6: See note 4 |
|
2 |
2 |
256 |
256 |
||||||||
|
3 |
3 |
256 |
256 |
||||||||
|
4 |
3 |
256 |
256 |
||||||||
|
5 |
6 |
256 |
256 |
||||||||
|
6 |
8 |
256 |
256 |
||||||||
|
7 |
8 |
512 |
512 |
||||||||
|
8 |
8 |
512 |
512 |
||||||||
|
9 |
8 |
1024 |
512 |
||||||||
|
10 |
5 |
1024 |
1024 |
||||||||
|
11 |
3 |
256 |
256 |
||||||||
|
12 |
8 |
256 |
256 |
||||||||
|
NOTE 1: The SS shall configure the RLC transmission and receiver window size depending on the UE category. The values are set to cope with the number of SDUs used in the sub-test and within the UE capabilities for the actual UE category under test. NOTE 2: UL_TFC0, UL_TFC1, UL_TFC2, and UL_TFC12 are part of minimum set of TFCIs. NOTE 3: See TS 34.109 [10] clause 5.3.2.6.2 for details regarding loopback of RLC SDUs. NOTE 4: The test data size for RB6 is dependent on the actual TFRC test point, see the generic test procedure in 14.1.3.5. |
|||||||||||
14.6.4.4 Test requirements
See 14.1.3.5 for definition of the referenced step numbers.
1. At step 12 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At steps 17 to 20 the UE transmitted transport format shall be within the set of restricted TFCIs as specified for the actual sub-test.
3. At step 18 and for each TFRC test point:
If the downlink RLC SDU size is less than the configured UL RLC SDU for the actual sub-test then the UE shall return 4 RLC SDUs where the first bits of each SDU has the same content as the RLC SDUs sent by the SS in downlink. Otherwise the UE shall return 4 RLC SDUs where each SDU has the same content as the first bits of the RLC SDUs sent by the SS in downlink.
NOTE: The generic test procedure as specified in 14.1.3.5.2 sends 4 SDUs of size (NPDUs * MAC-d PDU payload size) / 4 minus 8 bits (size of 7 bit length indicator and expansion bit). For the case when the downlink SDU size is less than the configured UL SDU size then all data is returned otherwise the returned data is truncated.