14.6.2 Interactive or background / UL:384 DL: [max bit rate depending on UE category] / PS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH

34.123-13GPPPart 1: Protocol conformance specificationRelease 15TSUser Equipment (UE) conformance specification

14.6.2.1 Conformance requirement

See 14.6.1.1.

14.6.2.2 Test purpose

To verify radio bearer establishment and correct data transfer for reference radio bearer configuration as specified in TS 34.108, clause 6.10.2.4.5.2.

14.6.2.3 Method of test

NOTE: The reference to UE Categories refers to the UE capability as signalled in the Rel-5 IE “HS-DSCH physical layer category” (1 to 12). All UEs supporting HS-DSCH should signal a category between 1 and 12 for this IE even if the UE physical capability category is above 12. This IE corresponds to the HS-DSCH category supported by the UE when MAC-ehs is not configured.

The following parameters are specific for this test case:

Parameter

Value

MAC-hs receiver window size

16

RLC Transmission window size

See sub-test table

RLC Receiving window size

See sub-test table

The generic test procedure in 14.1.3.5 is run for each sub-test.

Uplink TFS:

TFI

RB5

(384 kbps, 10ms)

DCCH

TFS

TF0, bits

0x336

0x148

TF1, bits

1×336

1×148

TF2, bits

2×336

N/A

TF3, bits

4×336

N/A

TF4, bits

8×336

N/A

TF5, bits

12×336

N/A

Uplink TFCS:

TFCI

(RB5, DCCH)

UL_TFC0

(TF0, TF0)

UL_TFC1

(TF1, TF0)

UL_TFC2

(TF2, TF0)

UL_TFC3

(TF3, TF0)

UL_TFC4

(TF4, TF0)

UL_TFC5

(TF5, TF0)

UL_TFC6

(TF0, TF1)

UL_TFC7

(TF1, TF1)

UL_TFC8

(TF2, TF1)

UL_TFC9

(TF3, TF1)

UL_TFC10

(TF4, TF1)

UL_TFC11

(TF5, TF1)

Sub-tests:

Sub-test

UE

Category

Number of HARQ processes

RLC Receiving window size

(note 1)

RLC Trans-mission window size

(note 1)

MAC-d PDU size
(bits)

Uplink TFCS

Under test

Implicitly tested

Restricted UL TFCIs

(note 2)

UL RLC SDU size

(bits)

(note 3)

1

1

2

512

256

336

UL_TFC1

UL_TFC0, UL_TFC6

UL_TFC0, UL_TFC1,

UL_TFC6,

UL_TFC7

RB5: 312

2

2

512

256

3

3

512

256

4

3

512

256

5

6

512

256

6

6

512

256

7

6

1536

512

8

6

1536

512

9

6

2047

512

10

6

2047

512

11

3

512

256

12

6

512

256

2

1

2

256

256

656

UL_TFC2

UL_TFC0, UL_TFC6

UL_TFC0, UL_TFC1,

UL_TFC2,

UL_TFC6,

UL_TFC8

RB5: 632

2

2

256

256

3

3

256

256

4

3

256

256

5

6

256

256

6

6

256

256

7

6

512

512

8

6

512

512

9

6

1024

512

10

6

1024

1024

11

3

256

256

12

6

256

256

3

1

2

512

256

336

UL_TFC3

UL_TFC0, UL_TFC6

UL_TFC0, UL_TFC1,

UL_TFC3,

UL_TFC6,

UL_TFC9

RB5: 1272

2

2

512

256

3

3

512

256

4

3

512

256

5

6

512

256

6

8

512

256

7

8

1536

512

8

8

1536

512

9

8

2047

512

10

6

2047

1024

11

3

512

256

12

8

512

256

4

1

2

256

256

656

UL_TFC4

UL_TFC0, UL_TFC6

UL_TFC0, UL_TFC1,

UL_TFC4,

UL_TFC6,

UL_TFC10

RB5: 2552

2

2

256

256

3

3

256

256

4

3

256

256

5

6

256

256

6

8

256

256

7

8

512

512

8

8

512

512

9

8

1024

512

10

6

1024

1024

11

3

256

256

12

8

256

256

5

1

2

256

256

656

UL_TFC5

UL_TFC0, UL_TFC6

UL_TFC0, UL_TFC1,

UL_TFC5,

UL_TFC6,

UL_TFC11

RB5: 3832

2

2

256

256

3

3

256

256

4

3

256

256

5

6

256

256

6

8

256

256

7

8

512

512

8

8

512

512

9

8

1024

512

10

6

1024

1024

11

3

256

256

12

8

256

256

NOTE 1: The SS shall configure the RLC transmission and receiver window size depending on the UE category. The values are set to cope with the number of SDUs used in the sub-test and within the UE capabilities for the actual UE category under test.

NOTE 2: UL_TFC0, UL_TFC1 and UL_TFC6 are part of minimum set of TFCIs.

NOTE 3: See TS 34.109 [10] clause 5.3.2.6.2 for details regarding loopback of RLC SDUs.
RB5: The UL RLC SDU size is set to N*UL RLC payload size minus 8 bits (size of 7 bit length indicator and expansion bit) , where N is the number of transport blocks for the UL transport format under test. This will enable the UE to return th data within one UL TTI.

14.6.2.4 Test requirements

See 14.1.3.5.2 for definition of step 12 and step 18.

1. At step 12 the UE shall send RADIO BEARER SETUP COMPLETE.

2. At step 18 the UE transmitted transport format shall be

– for sub-test 1: TF1 (1×336).

– for sub-test 2: TF2 (2×336).

– for sub-test 3: TF3 (4×336).

– for sub-test 4: TF4 (8×336).

– for sub-test 5: TF5 (12×336).

3. At step 18 and for each TFRC test point:

If the downlink RLC SDU size is less than the configured UL RLC SDU for the actual sub-test then the UE shall return 4 RLC SDUs where the first bits of each SDU has the same content as the RLC SDUs sent by the SS in downlink. Otherwise the UE shall return 4 RLC SDUs where each SDU has the same content as the first bits of the RLC SDUs sent by the SS in downlink.

NOTE: The generic test procedure as specified in 14.1.3.5.2 sends 4 SDUs of size (NPDUs * MAC-d PDU payload size) / 4 minus 8 bits (size of 7 bit length indicator and expansion bit). For the case when the downlink SDU size is less than the configured UL SDU size then all data is returned otherwise the returned data is truncated.