14.6.1f Interactive or background / UL:64 DL: [max bit rate depending on UE category] with Flexible RLC and MAC-ehs PS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH / DL: QPSK, 16QAM and Dual-Cell
34.123-13GPPPart 1: Protocol conformance specificationRelease 15TSUser Equipment (UE) conformance specification
14.6.1f.1 Conformance requirement
See 14.6.1.1.
14.6.1f.2 Test purpose
To verify radio bearer establishment and correct data transfer for reference radio bearer configuration as specified in TS 34.108, clause 6.10.2.4.5.1 for the QPSK, 16QAM and Dual-Cell case using the downlink enhanced Layer 2 configuration with Flexible RLC and MAC-ehs .
14.6.1f.3 Method of test
NOTE: The reference to UE Categories refers to the UE capability as signalled in the Rel-8 IE “HS-DSCH physical layer category extension 2”. This IE corresponds to the HS-DSCH category supported by the UE when MAC-ehs is configured.
The following parameters are specific for this test case:
|
Parameter |
Value |
Comments |
|
Radio bearer |
TS 34.108, clause 6.10.2.4.5.1 using downlink MAC-d flow parameters according to Alt 3 (Flexible RLC and MAC-ehs). |
|
|
MAC-ehs receiver window size |
16 |
|
|
RLC Transmission window size |
See sub-test table |
|
|
RLC Receiving window size |
See sub-test table |
The generic test procedure in 14.1.3.5a is run for each sub-test for test execution 1 to 3.
|
Execution counter |
Downlink Modulation Scheme (M1) Dual-Cell data flow#1 |
Downlink Modulation Scheme (M2) Dual-Cell data flow#2 |
Number of HARQ processes |
Dual-Cell |
|
1 |
QPSK |
QPSK |
6 |
Yes |
|
2 |
16QAM |
16QAM |
8 |
Yes |
|
3 |
16QAM |
QPSK |
8 |
Yes |
Uplink TFS:
|
TFI |
RB5 (64 kbps, 20 ms TTI) |
DCCH |
|
|
TFS |
TF0, bits |
0x336 |
0x148 |
|
TF1, bits |
1×336 |
1×148 |
|
|
TF2, bits |
2×336 |
N/A |
|
|
TF3, bits |
3×336 |
N/A |
|
|
TF4, bits |
4×336 |
N/A |
Uplink TFCS:
|
TFCI |
(RB5, DCCH) |
|
UL_TFC0 |
(TF0, TF0) |
|
UL_TFC1 |
(TF1, TF0) |
|
UL_TFC2 |
(TF2, TF0) |
|
UL_TFC3 |
(TF3, TF0) |
|
UL_TFC4 |
(TF4, TF0) |
|
UL_TFC5 |
(TF0, TF1) |
|
UL_TFC6 |
(TF1, TF1) |
|
UL_TFC7 |
(TF2, TF1) |
|
UL_TFC8 |
(TF3, TF1) |
|
UL_TFC9 |
(TF4, TF1) |
Sub-tests:
|
Sub-test |
UE Category |
RLC Receiving window size (note 1) |
RLC Trans-mission window size (note 1) |
MAC-d PDU size |
Uplink TFCS Under test |
Implicitly tested |
Restricted UL TFCIs (note 2) |
UL RLC SDU size (bits) (note 3) |
Test data size (bits) (note 4) |
|
1 |
21 to 24 |
2047 |
1024 |
Flexible |
UL_TFC4 |
UL_TFC0, UL_TFC5 |
UL_TFC0, UL_TFC1, UL_TFC4, UL_TFC5, UL_TFC9 |
RB5: 1272 |
See note 4 |
|
NOTE 1: The values are set to cope with the number of SDUs used in the sub-test and within the UE capabilities for the actual UE category under test. NOTE 2: UL_TFC0, UL_TFC1 and UL_TFC5 are part of minimum set of TFCIs. NOTE 3: See TS 34.109 [10] clause 5.3.2.6.2 for details regarding loopback of RLC SDUs. NOTE 4: The test data size and number of DL RLC SDUs for RB5 is dependent on the actual TFRC test point, see the generic test procedure in 14.1.3.5a. |
|||||||||
14.6.1f.4 Test requirements
See 14.1.3.5a for definition of step 12 and step 18.
1. At step 12 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At step 18 the UE transmitted transport format shall be
– for sub-test 1: TF4 (4×336)
3. At step 18 and for each TFRC test point:
The UE shall for each radio bearer return the equal number RLC SDUs as sent by the SS in downlink. If the downlink RLC SDU size is less than the configured UL RLC SDU for the actual sub-test then the UE shall return RLC SDUs where the first bits of each SDU has the same content as the RLC SDUs sent by the SS in downlink. Otherwise the UE shall return RLC SDUs where the SDU has the same content as the first bits of the RLC SDUs sent by the SS in downlink.
NOTE: The generic test procedure as specified in 14.1.3.5a sends either 2 SDU or 8 SDUs depending on the transport block size under tests.