14.6.1 Interactive or background / UL:64 DL: [max bit rate depending on UE category] / PS RAB + UL:3.4 DL:3.4 kbps SRBs for DCCH
34.123-13GPPPart 1: Protocol conformance specificationRelease 15TSUser Equipment (UE) conformance specification
14.6.1.1 Conformance requirement
For all transmissions of a transport block, the transport block size is derived from the TFRI value as specified below, except only in those cases of retransmissions where the Node-B selects a combination for which no mapping exists between the original transport block size and the selected combination of channelisation Code set and modulation type. In such cases, the transport block size index value signalled to the UE shall be set to 111111, i.e., ki=63.
Let ki be the TFRI signalled on the HS-SCCH value and let k0,i be the value in the table 9.2.3.1 corresponding to the modulation and the number of codes signalled on the HS-SCCH. Let kt be the sum of the two values: kt = ki + k0,i. The transport block size L(kt) can be obtained by accessing the position kt in the table in Annex A (normative) or by using the formula below (informative):
If kt < 40
else
End
Table 9.2.3.1: Values of k0,i for different numbers of channelization codes and modulation schemes
Combination i |
Modulation scheme |
Number of channelization codes |
|
0 |
QPSK |
1 |
1 |
1 |
2 |
40 |
|
2 |
3 |
63 |
|
3 |
4 |
79 |
|
4 |
5 |
92 |
|
5 |
6 |
102 |
|
6 |
7 |
111 |
|
7 |
8 |
118 |
|
8 |
9 |
125 |
|
9 |
10 |
131 |
|
10 |
11 |
136 |
|
11 |
12 |
141 |
|
12 |
13 |
145 |
|
13 |
14 |
150 |
|
14 |
15 |
153 |
|
15 |
16QAM |
1 |
40 |
16 |
2 |
79 |
|
17 |
3 |
102 |
|
18 |
4 |
118 |
|
19 |
5 |
131 |
|
20 |
6 |
141 |
|
21 |
7 |
150 |
|
22 |
8 |
157 |
|
23 |
9 |
164 |
|
24 |
10 |
169 |
|
25 |
11 |
175 |
|
26 |
12 |
180 |
|
27 |
13 |
184 |
|
28 |
14 |
188 |
|
29 |
15 |
192 |
The following table provides the mapping between kt (as per the definition in subclause 9.2.3.1) and the HS-DSCH Transport Block Size (L(kt)).
Table 9.2.3.2: mapping between kt (as per the definition in subclause 9.2.3.1) and the HS-DSCH Transport Block Size (L(kt))
Index |
TB Size |
Index |
TB Size |
Index |
TB Size |
1 |
137 |
86 |
1380 |
171 |
6324 |
2 |
149 |
87 |
1405 |
172 |
6438 |
3 |
161 |
88 |
1430 |
173 |
6554 |
4 |
173 |
89 |
1456 |
174 |
6673 |
5 |
185 |
90 |
1483 |
175 |
6793 |
6 |
197 |
91 |
1509 |
176 |
6916 |
7 |
209 |
92 |
1537 |
177 |
7041 |
8 |
221 |
93 |
1564 |
178 |
7168 |
9 |
233 |
94 |
1593 |
179 |
7298 |
10 |
245 |
95 |
1621 |
180 |
7430 |
11 |
257 |
96 |
1651 |
181 |
7564 |
12 |
269 |
97 |
1681 |
182 |
7700 |
13 |
281 |
98 |
1711 |
183 |
7840 |
14 |
293 |
99 |
1742 |
184 |
7981 |
15 |
305 |
100 |
1773 |
185 |
8125 |
16 |
317 |
101 |
1805 |
186 |
8272 |
17 |
329 |
102 |
1838 |
187 |
8422 |
18 |
341 |
103 |
1871 |
188 |
8574 |
19 |
353 |
104 |
1905 |
189 |
8729 |
20 |
365 |
105 |
1939 |
190 |
8886 |
21 |
377 |
106 |
1974 |
191 |
9047 |
22 |
389 |
107 |
2010 |
192 |
9210 |
23 |
401 |
108 |
2046 |
193 |
9377 |
24 |
413 |
109 |
2083 |
194 |
9546 |
25 |
425 |
110 |
2121 |
195 |
9719 |
26 |
437 |
111 |
2159 |
196 |
9894 |
27 |
449 |
112 |
2198 |
197 |
10073 |
28 |
461 |
113 |
2238 |
198 |
10255 |
29 |
473 |
114 |
2279 |
199 |
10440 |
30 |
485 |
115 |
2320 |
200 |
10629 |
31 |
497 |
116 |
2362 |
201 |
10821 |
32 |
509 |
117 |
2404 |
202 |
11017 |
33 |
521 |
118 |
2448 |
203 |
11216 |
34 |
533 |
119 |
2492 |
204 |
11418 |
35 |
545 |
120 |
2537 |
205 |
11625 |
36 |
557 |
121 |
2583 |
206 |
11835 |
37 |
569 |
122 |
2630 |
207 |
12048 |
38 |
581 |
123 |
2677 |
208 |
12266 |
39 |
593 |
124 |
2726 |
209 |
12488 |
40 |
605 |
125 |
2775 |
210 |
12713 |
41 |
616 |
126 |
2825 |
211 |
12943 |
42 |
627 |
127 |
2876 |
212 |
13177 |
43 |
639 |
128 |
2928 |
213 |
13415 |
44 |
650 |
129 |
2981 |
214 |
13657 |
45 |
662 |
130 |
3035 |
215 |
13904 |
46 |
674 |
131 |
3090 |
216 |
14155 |
47 |
686 |
132 |
3145 |
217 |
14411 |
48 |
699 |
133 |
3202 |
218 |
14671 |
49 |
711 |
134 |
3260 |
219 |
14936 |
50 |
724 |
135 |
3319 |
220 |
15206 |
51 |
737 |
136 |
3379 |
221 |
15481 |
52 |
751 |
137 |
3440 |
222 |
15761 |
53 |
764 |
138 |
3502 |
223 |
16045 |
54 |
778 |
139 |
3565 |
224 |
16335 |
55 |
792 |
140 |
3630 |
225 |
16630 |
56 |
806 |
141 |
3695 |
226 |
16931 |
57 |
821 |
142 |
3762 |
227 |
17237 |
58 |
836 |
143 |
3830 |
228 |
17548 |
59 |
851 |
144 |
3899 |
229 |
17865 |
60 |
866 |
145 |
3970 |
230 |
18188 |
61 |
882 |
146 |
4042 |
231 |
18517 |
62 |
898 |
147 |
4115 |
232 |
18851 |
63 |
914 |
148 |
4189 |
233 |
19192 |
64 |
931 |
149 |
4265 |
234 |
19538 |
65 |
947 |
150 |
4342 |
235 |
19891 |
66 |
964 |
151 |
4420 |
236 |
20251 |
67 |
982 |
152 |
4500 |
237 |
20617 |
68 |
1000 |
153 |
4581 |
238 |
20989 |
69 |
1018 |
154 |
4664 |
239 |
21368 |
70 |
1036 |
155 |
4748 |
240 |
21754 |
71 |
1055 |
156 |
4834 |
241 |
22147 |
72 |
1074 |
157 |
4921 |
242 |
22548 |
73 |
1093 |
158 |
5010 |
243 |
22955 |
74 |
1113 |
159 |
5101 |
244 |
23370 |
75 |
1133 |
160 |
5193 |
245 |
23792 |
76 |
1154 |
161 |
5287 |
246 |
24222 |
77 |
1175 |
162 |
5382 |
247 |
24659 |
78 |
1196 |
163 |
5480 |
248 |
25105 |
79 |
1217 |
164 |
5579 |
249 |
25558 |
80 |
1239 |
165 |
5680 |
250 |
26020 |
81 |
1262 |
166 |
5782 |
251 |
26490 |
82 |
1285 |
167 |
5887 |
252 |
26969 |
83 |
1308 |
168 |
5993 |
253 |
27456 |
84 |
1331 |
169 |
6101 |
254 |
27952 |
85 |
1356 |
170 |
6211 |
Reference(s)
3GPP TS 25.321, 9.2.3.1 and Annex A
14.6.1.2 Test purpose
To verify radio bearer establishment and correct data transfer for reference radio bearer configuration as specified in TS 34.108, clause 6.10.2.4.5.1.
14.6.1.3 Method of test
NOTE: The reference to UE Categories refers to the UE capability as signalled in the Rel-5 IE “HS-DSCH physical layer category” (1 to 12). All UEs supporting HS-DSCH should signal a category between 1 and 12 for this IE even if the UE physical capability category is above 12. This IE corresponds to the HS-DSCH category supported by the UE when MAC-ehs is not configured.
The following parameters are specific for this test case:
Parameter |
Value |
MAC-hs receiver window size |
16 |
RLC Transmission window size |
See sub-test table |
RLC Receiving window size |
See sub-test table |
The generic test procedure in 14.1.3.5 is run for each sub-test.
Uplink TFS:
TFI |
RB5 (64 kbps, 20 ms TTI) |
DCCH |
|
TFS |
TF0, bits |
0x336 |
0x148 |
TF1, bits |
1×336 |
1×148 |
|
TF2, bits |
2×336 |
N/A |
|
TF3, bits |
3×336 |
N/A |
|
TF4, bits |
4×336 |
N/A |
Uplink TFCS:
TFCI |
(RB5, DCCH) |
UL_TFC0 |
(TF0, TF0) |
UL_TFC1 |
(TF1, TF0) |
UL_TFC2 |
(TF2, TF0) |
UL_TFC3 |
(TF3, TF0) |
UL_TFC4 |
(TF4, TF0) |
UL_TFC5 |
(TF0, TF1) |
UL_TFC6 |
(TF1, TF1) |
UL_TFC7 |
(TF2, TF1) |
UL_TFC8 |
(TF3, TF1) |
UL_TFC9 |
(TF4, TF1) |
Sub-tests:
Sub-test |
UE Category |
Number of HARQ processes |
RLC Receiving window size (note 1) |
RLC Trans-mission window size (note 1) |
MAC-d PDU size |
Uplink TFCS Under test |
Implicitly tested |
Restricted UL TFCIs (note 2) |
UL RLC SDU size (bits) (note 3) |
1 |
1 |
2 |
512 |
128 |
336 |
UL_TFC1 |
UL_TFC0, UL_TFC5 |
UL_TFC0, UL_TFC1, UL_TFC5, UL_TFC6 |
RB5: 312 |
2 |
2 |
512 |
128 |
||||||
3 |
3 |
512 |
128 |
||||||
4 |
3 |
512 |
128 |
||||||
5 |
6 |
512 |
256 |
||||||
6 |
6 |
512 |
256 |
||||||
7 |
6 |
1536 |
512 |
||||||
8 |
6 |
1536 |
512 |
||||||
9 |
6 |
2047 |
512 |
||||||
10 |
6 |
2047 |
512 |
||||||
11 |
3 |
1024 |
128 |
||||||
12 |
6 |
1024 |
128 |
||||||
2 |
1 |
2 |
256 |
128 |
656 |
UL_TFC2 |
UL_TFC0, UL_TFC5 |
UL_TFC0, UL_TFC1, UL_TFC2, UL_TFC5, UL_TFC7 |
RB5: 632 |
2 |
2 |
256 |
128 |
||||||
3 |
3 |
256 |
128 |
||||||
4 |
3 |
256 |
128 |
||||||
5 |
6 |
256 |
256 |
||||||
6 |
6 |
256 |
256 |
||||||
7 |
6 |
512 |
512 |
||||||
8 |
6 |
512 |
512 |
||||||
9 |
6 |
1024 |
512 |
||||||
10 |
6 |
1024 |
1024 |
||||||
11 |
3 |
512 |
128 |
||||||
12 |
6 |
512 |
128 |
||||||
3 |
1 |
2 |
512 |
256 |
336 |
UL_TFC3 |
UL_TFC0, UL_TFC5 |
UL_TFC0, UL_TFC1, UL_TFC3, UL_TFC5, UL_TFC8 |
RB5: 952 |
2 |
2 |
512 |
256 |
||||||
3 |
3 |
512 |
256 |
||||||
4 |
3 |
512 |
256 |
||||||
5 |
6 |
512 |
256 |
||||||
6 |
8 |
512 |
256 |
||||||
7 |
8 |
1536 |
512 |
||||||
8 |
8 |
1536 |
512 |
||||||
9 |
8 |
2047 |
512 |
||||||
10 |
6 |
2047 |
1024 |
||||||
11 |
3 |
1024 |
128 |
||||||
12 |
8 |
1024 |
128 |
||||||
4 |
1 |
2 |
256 |
256 |
656 |
UL_TFC4 |
UL_TFC0, UL_TFC5 |
UL_TFC0, UL_TFC1, UL_TFC4, UL_TFC5, UL_TFC9 |
RB5: 1272 |
2 |
2 |
256 |
256 |
||||||
3 |
3 |
256 |
256 |
||||||
4 |
3 |
256 |
256 |
||||||
5 |
6 |
256 |
256 |
||||||
6 |
8 |
256 |
256 |
||||||
7 |
8 |
512 |
512 |
||||||
8 |
8 |
512 |
512 |
||||||
9 |
8 |
1024 |
512 |
||||||
10 |
6 |
1024 |
1024 |
||||||
11 |
3 |
512 |
128 |
||||||
12 |
8 |
512 |
128 |
||||||
NOTE 1: The SS shall configure the RLC transmission and receiver window size depending on the UE category. The values are set to cope with the number of SDUs used in the sub-test and within the UE capabilities for the actual UE category under test. NOTE 2: UL_TFC0, UL_TFC1 and UL_TFC5 are part of minimum set of TFCIs. NOTE 3: See TS 34.109 [10] clause 5.3.2.6.2 for details regarding loopback of RLC SDUs. |
14.6.1.4 Test requirements
See 14.1.3.5 for definition of step 12 and step 18.
1. At step 12 the UE shall send RADIO BEARER SETUP COMPLETE.
2. At step 18 the UE transmitted transport format shall be
– for sub-test 1: TF1 (1×336).
– for sub-test 2: TF2 (2×336).
– for sub-test 3: TF3 (3×336).
– for sub-test 4: TF4 (4×336)
3. At step 18 and for each TFRC test point:
If the downlink RLC SDU size is less than the configured UL RLC SDU for the actual sub-test then the UE shall return 4 RLC SDUs where the first bits of each SDU has the same content as the RLC SDUs sent by the SS in downlink. Otherwise the UE shall return 4 RLC SDUs where each SDU has the same content as the first bits of the RLC SDUs sent by the SS in downlink.
NOTE The generic test procedure as specified in 14.1.3.5.2 sends 4 SDUs of size (NPDUs * MAC-d PDU payload size) / 4 minus 8 bits (size of 7 bit length indicator and expansion bit). For the case when the downlink SDU size is less than the configured UL SDU size then all data is returned otherwise the returned data is truncated.