9.1.1 Default RRC Message Contents (FDD)

34.1083GPPCommon test environments for User Equipment (UE)Conformance testingRelease 15TS

Tools: ARFCN - Frequency Conversion for 5G NR/LTE/UMTS/GSM

This clause contains the default values of common messages, which unless indicated otherwise in specific clauses of 3GPP TS 34.123-1 [1], shall be transmitted and checked by the system simulator.

In this clause, decimal values are normally used. However, sometimes a hexadecimal value, indicated by an "H", or a binary value, indicated by a "B" is used.

The necessary L3 messages are listed in alphabetic order, with the exception of the SYSTEM INFORMATION messages, where it is the information elements which are listed in alphabetic order (this is because some information elements occur in several SYSTEM INFORMATION types).

Default SYSTEM INFORMATION:

NOTE: SYSTEM INFORMATION BLOCK TYPE 1 (except for PLMN type "GSM-MAP"), SYSTEM INFORMATION BLOCK TYPE 8, SYSTEM INFORMATION BLOCK TYPE 9, SYSTEM INFORMATION BLOCK TYPE 10, SYSTEM INFORMATION BLOCK TYPE 14, SYSTEM INFORMATION BLOCK TYPE 15 and SYSTEM INFORMATION BLOCK TYPE 16 messages are not used.

Contents of ACTIVE SET UPDATE message: AM

Information Element	Value/remark	Version
Message Type
RRC transaction identifier	Arbitrarily selects one integer between 0 to 3
Integrity check info
– message authentication code	SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC message sequence number	SS provides the value of this IE, from its internal counter.
Activation time	Now
New U-RNTI	Not Present
New H-RNTI	Not Present	Rel-6
New Primary E-RNTI	Not Present	Rel-6
New Secondary E-RNTI	Not Present	Rel-6
CN information info	Not Present
DTX-DRX timing information	Not Present	Rel-7
DTX-DRX Information	Not Present	Rel-7
HS-SCCH less Information	Not Present	Rel-7
MIMO parameters	Not Present	Rel-7
MIMO mode with four transmit antennas parameters	Not Present	Rel-11
DCH Enhancements info FDD	Not Present	Rel-12
Maximum allowed UL TX power	Not Present – use default value
Uplink secondary cell info FDD	Not Present	Rel-9
E-DCH reconfiguration information on secondary UL frequency	Not Present	Rel-9
Uplink CLTD info FDD	Not Present	Rel-11
F-TPICH reconfiguration info	Not Present	Rel-11
Uplink OLTD info FDD	Not Present	Rel-11
Radio link addition information	Not Present
Radio link addition information on secondary UL frequency	Not Present	Rel-9
Serving Cell Change Parameters	Not present	Rel-8
Radio link removal information	Not Present
Radio link removal information on secondary UL frequency	Not present	Rel-9
TX Diversity Mode	None
SSDT information	Not Present	R99 and Rel-4 only
DPC Mode	Not Present	Rel-5
Serving HS-DSCH cell information	Not Present	Rel-6
E-DCH reconfiguration information	Not Present	Rel-6
UL 16QAM configuration	Not Present	Rel-7
UL 64QAM configuration	Not Present	Rel-11
Uplink MIMO info FDD	Not Present	Rel-11
E-DCH reconfiguration information same serving cell	Not Present	Rel-7
E-TFC Boost Info	Not Present	Rel-7
E-DPDCH power interpolation	Not Present	Rel-7
Downlink secondary cell info FDD	Not present	Rel-8
Additional downlink secondary cell info list FDD	Not present	Rel-10
Downlink secondary cell info FDD	Not Present	Rel-10
Additional downlink secondary cell info list FDD 2	Not present	Rel-11
Downlink secondary cell info FDD	Not Present	Rel-11

Contents of ACTIVE SET UPDATE COMPLETE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if it matches the same value used in the corresponding downlink ACTIVE SET UPDATE message
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.

Contents of ACTIVE SET UPDATE FAILURE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if it matches the same value used in the corresponding downlink ACTIVE SET UPDATE message
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Failure cause	Refer to test requirement

Contents of CELL UPDATE message: TM

Information Element	Value/remark	Version
Message Type
U-RNTI	Checked to see if it is set to the following values
– SRNC identity	0000 0000 0001B
– S-RNTI	0000 0000 0000 0000 0001B
RRC transaction identifier	Checked to see if it is absent
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
START List	Checked to see if the ‘CN domain identity’ and ‘START’ IEs are present for all CN domains supported by the UE .
	Checked to see if the ‘CN domain identity’ and ‘START’ IEs are present for each CN domain for which RABs are established or is the latest configured CN domain.	Rel-6
– CN domain identity	Checked to see if it is one of the supported CN domains
– START	This IE is checked to see if it is present. The first/ leftmost bit of the bit string contains the most significant bit of the START.
AM_RLC error indication (RB2, RB3 or RB4)	Checked to see if it is set to ‘FALSE’
AM_RLC error indication (RB>4)	Checked to see if it is set to ‘FALSE’
Cell update cause	See the specific test case
Traffic volume indicator	Checked to see if it is absent	Rel-6
Failure cause	Checked to see if it is absent
RB timer indicator
– T314 expired	Checked to see if it is set to ‘FALSE’
– T315 expired	Checked to see if it is set to ‘FALSE’
Establishment cause	This IE is checked to see if it is absent	Rel-5
CS Call Type	Not Present	Rel-7
HS-PDSCH in CELL_FACH	Not checked	Rel-7
UE Mobility State Indicator	Not Present	Rel-7
Capability change indicator	Not Present	Rel-7
Reconfiguration Status Indicator	Checked to see if it is absent	Rel-6
Measured results on RACH	Not checked
Logged Meas Available	Not Present	Rel-10
ANR Logging Results Available	Not Present	Rel-10

Contents of CELL UPDATE CONFIRM message: UM

Information Element	Value/remark	Version
Message Type
U-RNTI	If this message is sent on CCCH, use the following values. Else, this IE is absent.
– SRNC identity	0000 0000 0001B
– S-RNTI	0000 0000 0000 0000 0001B
RRC transaction identifier	Selects an arbitrary integer between 0 to 3
Integrity check info
– message authentication code	SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC message sequence number	SS provides the value of this IE, from its internal counter.
Integrity protection mode info	Not Present
Ciphering mode info	Not Present
Activation time	Not Present – use default value
New U-RNTI	Not Present
New C-RNTI	Not Present
New DSCH-RNTI	Not Present	R99 and Rel-4 only
New H-RNTI	Not Present	Rel-5
New Primary E-RNTI	Not present	Rel-6
New Secondary E-RNTI	Not present	Rel-6
RRC State indicator	CELL_FACH
UTRAN DRX cycle length coefficient	Not Present
RLC re-establish indicator (RB2, RB3 and RB4)	FALSE
RLC re-establish indicator (RB5 and upwards)	FALSE
CN information info	Not Present
URA identity	Not Present
RNC support for change of UE capability	Not Present	Rel-7
RB information to release list	Not Present
RB information to reconfigure list	Not Present
RB information to be affected list	Not Present
Downlink counter synchronization info	Not Present
PDCP ROHC target mode	Not Present	Rel-5
UL Transport channel information common for all transport channels	Not Present
Deleted TrCH information list	Not Present
Added or Reconfigured TrCH information list	Not Present
CHOICE Mode	FDD
– CPCH set ID	Not Present	R99 and Rel-4 only
– Added or Reconfigured TrCH information for DRAC list	Not Present	R99 and Rel-4 only
DL Transport channel information common for all transport channels	Not Present
Deleted TrCH information list	Not Present
Added or Reconfigured TrCH information list	Not Present
Frequency info	Not Present
DTX-DRX timing information	Not Present	Rel-7
DTX-DRX Information	Not Present	Rel-7
HS-SCCH less Information	Not Present	Rel-7
MIMO parameters	Not Present	Rel-7
MIMO mode with four transmit antennas parameters	Not Present	Rel-11
DCH Enhancements info FDD	Not Present	Rel-12
Maximum allowed UL TX power	Not Present
CHOICE channel requirement	Not Present
E-DCH Info	Not Present	Rel-6
CHOICE mode	FDD	R99 and Rel-4 only
– Downlink PDSCH information	Not Present	R99 and Rel-4 only
Uplink secondary cell info FDD	Not Present	Rel-9
Uplink CLTD info FDD	Not Present	Rel-11
Uplink OLTD info FDD	Not Present	Rel-11
Downlink HS-PDSCH Information	Not Present	Rel-5
Downlink information common for all radio links	Not Present
Downlink information per radio link list	Not Present
Downlink information for each radio link	Not Present
Downlink secondary cell info FDD	Not Present	Rel-8
Additional downlink secondary cell info list FDD	Not present	Rel-10
Downlink secondary cell info FDD	Not Present	Rel-10
Additional downlink secondary cell info list FDD 2	Not present	Rel-11
Downlink secondary cell info FDD	Not Present	Rel-11
Common E-RGCH info FDD	Not Present	Rel-11
MBMS PL Service Restriction Information	Not Present	Rel-6

Contents of DOWNLINK DIRECT TRANSFER message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Arbitrarily selects an integer between 0 and 3
Integrity check info
– Message authentication code	SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	SS provides the value of this IE, from its internal counter.
CN domain identity	CS domain or PS domain
NAS message	See Specific Message Content for each test case

Contents of HANDOVER FROM UTRAN COMMAND-GSM message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Arbitrarily selects one integer between 0 to 3
Integrity check info
– Message authentication code	SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	SS provides the value of this IE, from its internal counter.
Activation time	now
RAB Info
– RAB identity	0000 0001B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.
– CN domain identity	CS domain
– NAS Synchronization Indicator	Not present
– Re-establishment timer	Use T314
Inter-system message
– CHOICE System type	GSM
– Frequency Band	Set to "GSM/ PCS 1900" if GSM/ PCS 1900 is used in this test. Otherwise set to "GSM/DCS 1800 Band"
– CHOICE GSM message	Single GSM message
– Single GSM message	GSM HANDOVER COMMAND formatted and coded according to GSM specifications as BIT STRING (1..512). The first/ leftmost/ most significant bit of the bit string contains bit 8 of the first octet of the GSM message. The contents of the HANDOVER COMMAND is to be defined in the specific test case.

Contents of HANDOVER FROM UTRAN FAILURE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if it matches the same value used in the corresponding downlink HANDOVER FROM UTRAN COMMAND -GSM message
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Inter-RAT handover failure
-Inter-RAT handover failure cause	physical channel failure
Inter-system message	Not Checked

Contents of INITIAL DIRECT TRANSFER message: AM

Information Element	Value/remark	Version
Message Type
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
PLMN identity	This IE is checked to see if it is absent	Rel-6
CN domain identity	Checked to see if set to supported CN domain as specified in the IXIT statements.
Intra Domain NAS Node Selector
– CHOICE version	R99
– CHOICE CN type	GSM-MAP
– CHOICE Routing basis	Local (P)TMSI
– Routing parameter	If the IE "CN domain identity" is equal to "CS domain", this bit string is set to bits b14 through b23 of the TMSI. If the IE "CN domain identity" is equal to "PS domain", this bit string is set to bits b14 through b23 of the P-TMSI. The TMSI/P-TMSI consists of 4 octets (32bits). This can be represented by a string of bits numbered from b0 to b31, with bit b0 being the least significant The "Routing parameter" bit string consists of bits b14 through b23 of the TMSI/ PTMSI. The first/ leftmost/ most significant bit of the bit string contains bit b23 of the TMSI/ PTMSI.
– Entered parameter	Not checked
NAS message	Set according to that indicated in specific message content for each test case
START	This IE is checked to see if it is present.
Establishment cause	This IE is checked to see if it is absent	Rel-5
Measured results on RACH	Not checked
MBMS joined information	This IE is checked to see if it is absent	Rel-6

Contents of LOGGING MEASUREMENT CONFIGURATION message: AM

Information Element	Condition	Value/remark	Version
Message Type			Rel-10
RRC transaction identifier		Arbitrarily selects an integer between 0 and 3	Rel-10
Integrity check info			Rel-10
– message authentication code		SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC message sequence number		SS provides the value of this IE, from its internal counter.
Logged Measurements Configuration Info	A1, A2	Not present	Rel-10
Logged ANR configuration Info	A1, A2		Rel-10
– Logging Duration		1 hour
– Intra-UTRA ANR
– CHOICE Absolute Threshold	A1	RSCP for ANR
– RSCP		Not present (default -100 dBm)
– CHOICE Absolute Threshold	A2	Ec/N0 for ANR
– Ec/N0		Not present (default -10 dB)
– Logging Relative Threshold		Not present
– Inter-RAT ANR for E-UTRA Indicator		Not present
– Inter-RAT ANR for GSM Indicator		Not present

Condition	Explanation	Version
A1	Configuring of IE for ANR over UTRAN testing using RSCP for Absolute Threshold	Rel-10
A2	Configuring of IE for ANR over UTRAN testing using Ec/N0 for Absolute Threshold	Rel-10

Contents of MBMS ACCESS INFORMATION message: UM

Information Element	Value/remark	Version
Message type		Rel-6
Service list	1 entry in the list	Rel-6
– MBMS short transmission ID	Index to the MBMS transmission identity in the previous MBMS MODIFIED SERVICES INFORMATION or MBMS UNMODIFIED SERVICES INFORMATION corresponding to the service for which the current counting procedure applies.	Rel-6
– Access probability factor – Idle	0 (corresponding to the actual probability factor value 1)	Rel-6
– Connected mode counting scope		Rel-6
– URA_PCH	FALSE	Rel-6
– CELL_PCH	FALSE	Rel-6
– CELL_FACH	FALSE	Rel-6

Contents of MBMS GENERAL INFORMATION message: UM

Information Element	Value/remark	Version
Message type		Rel-6
MBMS preferred frequency information	Not Present	Rel-6
MBMS timers and counters		Rel-6
– T318	4000 ms	Rel-6
MICH configuration information		Rel-6
– MICH Power offset	-5dB	Rel-6
– CHOICE Mode	FDD	Rel-6
– Channelisation code	Reference to clause 5.5.1.4 “Downlink physical channels code allocation for MBMS test cases”	Rel-6
– Number of NI per frame	18	Rel-6
– STTD indicator	FALSE	Rel-6
Cell group identity	‘000000000001’ ( cells with mid range UARFCN ) ‘000000000010’ ( cells with low range UARFCN ) ‘000000000011’ ( cells with high range UARFCN )	Rel-6
Default MSCH configuration information	Not Present	Rel-6
Indicate changes in MBMS Selected Services	Not Present	Rel-6

Contents of MBMS COMMON P-T-M RB INFORMATION message: UM

Information Element	Value/remark	Version
Message type		Rel-6
RB information list	2 entries in the list	Rel-6
– RB identity	14	Rel-6
– PDCP info
– Support for lossless SRNS relocation	Not Present
– PDCP PDU header	absent
– Header compression information	Not Present
– RLC info
– DL UM RLC LI size	7
– DL Duplication Avoidance and Reordering info	Not Present
– RB identity	15	Rel-6
– PDCP info
– Support for lossless SRNS relocation	Not Present
– PDCP PDU header	absent
– Header compression information	Not Present
– RLC info
– DL UM RLC LI size	7
– DL Duplication Avoidance and Reordering info	Not Present
TrCh information for each TrCh	2 entries in the list	Rel-6
– Transport channel identity	17	Rel-6
– TFS
– CHOICE Transport channel type	Common transport channels
– Dynamic Transport format information
– RLC Size	Reference to clause 6.10 parameter set
– Number of TBs List	(This IE is repeated for TFI number.)
– Transmission Time Interval	Not Present
– Number of Transport blocks	Reference to clause 6.10 parameter set
– CHOICE Logical channel list	All
– Semi-static Transport Format information
– Transmission time interval	Reference to clause 6.10 parameter set
– Type of channel coding	Reference to clause 6.10 parameter set
– Coding Rate	Reference to clause 6.10 parameter set
– Rate matching attribute	Reference to clause 6.10 parameter set
– CRC size	Reference to clause 6.10 parameter set
– Transport channel identity	23	Rel-6
– TFS
– CHOICE Transport channel type	Common transport channels
– Dynamic Transport format information
– RLC Size	Reference to clause 6.10 parameter set
– Number of TBs List	(This IE is repeated for TFI number.)
– Transmission Time Interval	Not Present
– Number of Transport blocks	Reference to clause 6.10 parameter set
– CHOICE Logical channel list	All
– Semi-static Transport Format information
– Transmission time interval	Reference to clause 6.10 parameter set
– Type of channel coding	Reference to clause 6.10 parameter set
– Coding Rate	Reference to clause 6.10 parameter set
– Rate matching attribute	Reference to clause 6.10 parameter set
– CRC size	Reference to clause 6.10 parameter set
TrCh information for each CCTrCh	2 entries in the list	Rel-6
– CCTrCH identity	1	Rel-6
– TFCS
– CHOICE TFCI signalling	Normal
– TFCI Field 1 information
– CHOICE TFCS representation	Complete reconfiguration
– TFCS complete reconfiguration information
– CHOICE CTFC Size	Number of bits used must be enough to cover all combinations of CTFC from clause 6.10.
– CTFC information	This IE is repeated for number of CTFCs in clause 6.10 "Parameter Set"
– CTFC	Reference to clause 6.10 "Parameter Set"
– Power offset information	Not Present
– CCTrCH identity	2	Rel-6
– TFCS
– CHOICE TFCI signalling	Normal
– TFCI Field 1 information
– CHOICE TFCS representation	Complete reconfiguration
– TFCS complete reconfiguration information
– CHOICE CTFC Size	Number of bits used must be enough to cover all combinations of CTFC from clause 6.10.
– CTFC information	This IE is repeated for number of CTFCs in clause 6.10 "Parameter Set"
– CTFC	Reference to clause 6.10 "Parameter Set"
– Power offset information	Not Present
PhyCh information	2 entries in list	Rel-6
– PhyCh identity	13	Rel-6
– Secondary CCPCH info MBMS
– CHOICE mode	FDD
– Secondary scrambling code	Not Present
– STTD indicator	FALSE
– Spreading factor	Reference to clause 6.10 "Parameter Set"
– Code number	Reference to clause 5.5.1.4 “Downlink physical channels code allocation for MBMS test cases”
– Timing Offset	Set to (Cell No. – 21) * 18 for MBMS Cell Nos. 21-28. (actual value = IE value * 256 chips)
– PhyCh identity	17	Rel-6
– Secondary CCPCH info MBMS
– CHOICE mode	FDD
– Secondary scrambling code	Not Present
– STTD indicator	FALSE
– Spreading factor	Reference to clause 6.10 "Parameter Set"
– Code number	Reference to clause 5.5.1.4 “Downlink physical channels code allocation for MBMS test cases”
– Timing Offset	Set to (Cell No. – 21) * 18 for MBMS Cell Nos. 21-28. (actual value = IE value * 256 chips)

Contents of MBMS CURRENT CELL P-T-M RB INFORMATION message: UM

Information Element	Condition	Value/remark	Version
Message type	A1, A2, A3		Rel-6
S-CCPCH list	A1	Not Present	Rel-6
S-CCPCH list	A2	Contains 1 S-CCPCH	Rel-6
S-CCPCH list	A3	Contains 2 S-CCPCH	Rel-6
– S-CCPCH identity	A2, A3	1 if combining is used in the test (MBMS NEIGHBOURING CELL P-T-M RB INFORMATION is transmitted in the same modification period). Not Present if combining is not used in the test (MBMS NEIGHBOURING CELL P-T-M RB INFORMATION is not transmitted in the same modification period).	Rel-6
– Secondary CCPCH info		13	Rel-6
– MBMS Soft Combining Timing Offset		Not Present	Rel-6
– TrCh information common for all TrCh		1	Rel-6
– TrCH information list			Rel-6
– TrCh information		17	Rel-6
– RB information list			Rel-6
– RB information		14	Rel-6
– MBMS short transmission ID		Refers to the index of the service in the list of services on the cell which is being provided on this RB	Rel-6
– MBMS logical channel identity		1	Rel-6
– MSCH configuration information		Not Present	Rel-6
– S-CCPCH identity	A3	Not Present	Rel-6
– Secondary CCPCH info		17	Rel-6
– MBMS Soft Combining Timing Offset		Not Present	Rel-6
– TrCh information common for all TrCh		2	Rel-6
– TrCH information list			Rel-6
– TrCh information		23	Rel-6
– RB information list			Rel-6
– RB information		15	Rel-6
– MBMS short transmission ID		Refers to the index of the service in the list of services on the cell which is being provided on this RB	Rel-6
– MBMS logical channel identity		2	Rel-6
– MSCH configuration information		Not Present	Rel-6
S-CCPCH in SIB type 5	A1, A2, A3	Not Present	Rel-6

Condition	Explanation
A1	No services ongoing or starting
A2	1 service ongoing or starting
A3	2 services ongoing or starting

Contents of MBMS MODIFIED SERVICES INFORMATION message: UM

Information Element	Value/remark	Version
Message type		Rel-6
Modified services list	1 entry per modified service – maximum 12. If no services are modified in the current modification period this IE is Not Present	Rel-6
– MBMS Transmission identity		Rel-6
– MBMS Service ID
– MBMS Service ID	Set to the value of the service ID being modified (e.g. ‘000001’)	Rel-6
– CHOICE PLMN identity	SameAs-MIB	Rel-6
– MBMS Session ID	‘01’	Rel-6
– MBMS required UE action	Acquire PTM RB info	Rel-6
– MBMS preferred frequency	Not Present	Rel-6
– Continue MCCH reading	FALSE	Rel-6
MBMS re- acquire MCCH	Not Present	Rel-6
MBMS dynamic persistence level	Not Present	Rel-6
End of modified MCCH information	Not Present	Rel-6
MBMS number of neighbour cells	0	Rel-6
MBMS all unmodified p-t-m services	Not Present	Rel-6
MBMS p-t-m activation time	Not Present	Rel-6

Contents of MBMS NEIGHBOURING CELL P-T-M RB INFORMATION message: UM

Information Element	Value/remark	Version
Message type		Rel-6
Neighbouring cell identity	The intra-frequency cell id of the cell of the MBMS neighbouring cell referred to in the test procedure, obtained from the IE ‘Intra-frequency Cell Info list’ in SIB 11.	Rel-6
Neighbouring cell’s S-CCPCH list	1 entry in the list	Rel-6
– Secondary CCPCH info	Refers to the Physical channel identity being used for the service under test in the common RB info of the current cell	Rel-6
– Secondary CCPCH Power Offset Difference	Not Present	Rel-6
– L1 combining	Not Present	Rel-6
– CHOICE L23 configuration	SameAs Current cell	Rel-6
– Current cell’s S-CCPCH	1 (same as the S-CCPCH identity in the MBMS CURRENT CELL P-T-M RB INFORMATION)	Rel-6
– MSCH configuration information	Not Present	Rel-6

Contents of MBMS UNMODIFIED SERVICES INFORMATION message: UM

Information Element	Value/remark	Version
Message type		Rel-6
Unmodified services list	12 services by default. See NOTE 1.	Rel-6
– MBMS Transmission identity		Rel-6
– MBMS Service ID
– MBMS Service ID	‘000001’	Rel-6
– CHOICE PLMN identity	SameAs-MIB	Rel-6
– MBMS Session ID	Value set according to table for condition A1 or A2	Rel-6
– MBMS required UE action	Value set according to table for condition A1 or A2	Rel-6
– MBMS preferred frequency	Not Present	Rel-6
– MBMS Transmission identity		Rel-6
– MBMS Service ID
– MBMS Service ID	‘000002’	Rel-6
– CHOICE PLMN identity	SameAs-MIB	Rel-6
– MBMS Session ID	Value set according to table for condition A1 or A2	Rel-6
– MBMS required UE action	Value set according to table for condition A1 or A2	Rel-6
– MBMS preferred frequency	Not Present	Rel-6
– MBMS Transmission identity		Rel-6
– MBMS Service ID
– MBMS Service ID	‘000003’	Rel-6
– CHOICE PLMN identity	SameAs-MIB	Rel-6
– MBMS Session ID	Value set according to table for condition A1 or A2	Rel-6
– MBMS required UE action	Value set according to table for condition A1 or A2	Rel-6
– MBMS preferred frequency	Not Present	Rel-6
– MBMS Transmission identity		Rel-6
– MBMS Service ID
– MBMS Service ID	‘000004’	Rel-6
– CHOICE PLMN identity	SameAs-MIB	Rel-6
– MBMS Session ID	Value set according to table for condition A1 or A2	Rel-6
– MBMS required UE action	Value set according to table for condition A1 or A2	Rel-6
– MBMS preferred frequency	Not Present	Rel-6
– MBMS Transmission identity		Rel-6
– MBMS Service ID
– MBMS Service ID	‘000005’	Rel-6
– CHOICE PLMN identity	SameAs-MIB	Rel-6
– MBMS Session ID	Value set according to table for condition A1 or A2	Rel-6
– MBMS required UE action	Value set according to table for condition A1 or A2	Rel-6
– MBMS preferred frequency	Not Present	Rel-6
– MBMS Transmission identity		Rel-6
– MBMS Service ID
– MBMS Service ID	‘000006’	Rel-6
– CHOICE PLMN identity	SameAs-MIB	Rel-6
– MBMS Session ID	Value set according to table for condition A1 or A2	Rel-6
– MBMS required UE action	Value set according to table for condition A1 or A2	Rel-6
– MBMS preferred frequency	Not Present	Rel-6
– MBMS Transmission identity		Rel-6
– MBMS Service ID
– MBMS Service ID	‘000007’	Rel-6
– CHOICE PLMN identity	SameAs-MIB	Rel-6
– MBMS Session ID	Value set according to table for condition A1 or A2	Rel-6
– MBMS required UE action	Value set according to table for condition A1 or A2	Rel-6
– MBMS preferred frequency	Not Present	Rel-6
– MBMS Transmission identity		Rel-6
– MBMS Service ID
– MBMS Service ID	‘000008’	Rel-6
– CHOICE PLMN identity	SameAs-MIB	Rel-6
– MBMS Session ID	Value set according to table for condition A1 or A2	Rel-6
– MBMS required UE action	Value set according to table for condition A1 or A2	Rel-6
– MBMS preferred frequency	Not Present	Rel-6
– MBMS Transmission identity		Rel-6
– MBMS Service ID
– MBMS Service ID	‘000009’	Rel-6
– CHOICE PLMN identity	SameAs-MIB	Rel-6
– MBMS Session ID	Value set according to table for condition A1 or A2	Rel-6
– MBMS required UE action	Value set according to table for condition A1 or A2	Rel-6
– MBMS preferred frequency	Not Present	Rel-6
– MBMS Transmission identity		Rel-6
– MBMS Service ID
– MBMS Service ID	‘00000A’	Rel-6
– CHOICE PLMN identity	SameAs-MIB	Rel-6
– MBMS Session ID	Value set according to table for condition A1 or A2	Rel-6
– MBMS required UE action	Value set according to table for condition A1 or A2	Rel-6
– MBMS preferred frequency	Not Present	Rel-6
– MBMS Transmission identity		Rel-6
– MBMS Service ID
– MBMS Service ID	‘00000B’	Rel-6
– CHOICE PLMN identity	SameAs-MIB	Rel-6
– MBMS Session ID	Value set according to table for condition A1 or A2	Rel-6
– MBMS required UE action	Value set according to table for condition A1 or A2	Rel-6
– MBMS preferred frequency	Not Present	Rel-6
– MBMS Transmission identity		Rel-6
– MBMS Service ID
– MBMS Service ID	‘00000C’	Rel-6
– CHOICE PLMN identity	SameAs-MIB	Rel-6
– MBMS Session ID	Value set according to table for condition A1 or A2	Rel-6
– MBMS required UE action	Value set according to table for condition A1 or A2	Rel-6
– MBMS preferred frequency	Not Present	Rel-6

Information Element	Condition	Value/remark	Explanation
– MBMS Session ID	A1	Not Present	Condition used when the session is currently not being transmitted
– MBMS required UE action		‘None’
– MBMS Session ID	A2	‘01’	Condition used when the session is currently ongoing
– MBMS required UE action		‘Acquire PTM RB info’

NOTE 1: Any service ID which is included in MBMS MODIFIED SERVICES INFORMATION in the current modification period shall be Not Present in the list of services in this message.

Contents of MEASUREMENT CONTROL message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Arbitrarily selects an unused integer between 0 to 3
Integrity check info
– Message authentication code	SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC message sequence number	SS provides the value of this IE, from its internal counter.
Measurement Identity	1
Measurement Command	Setup
Measurement Reporting Mode
– Measurement Report Transfer Mode	Acknowledged mode RLC
– Periodical Reporting/Event Trigger Reporting Mode	Periodical reporting
Additional measurement list	Not Present
CHOICE Measurement type	Intra-frequency measurement
– Intra-frequency measurement
– Intra-frequency cell info list
– CHOICE intra-frequency cell removal	Not present
– New intra-frequency cell
– Intra-frequency cell-id	1
– Cell info
– Cell individual offset	0 (0dB)
– Reference time difference to cell	Not Present
– Read SFN number	FALSE
– CHOICE mode	FDD
– Primary CPICH info
– Primary scrambling code	Different from the Default setting in clause 6.1 (FDD)
– Primary CPICH Tx power	Not Present
– TX Diversity indicator	FALSE
– Cells for measurement	Not present
– CSG Intrafrequency cell info	Not present
– Intra-frequency SI Acquisition	Not present
– Intra-frequency measurement quantity	Not Present
– Intra-frequency reporting quantity
– Reporting quantities for active set cells
– Cell synchronization information reporting indicator	FALSE
– Cell Identity reporting indicator	TRUE
– CPICH Ec/N0 reporting indicator	FALSE
– CPICH RSCP reporting indicator	TRUE
– Pathloss reporting indicator	FALSE
– Reporting quantities for monitored set cells
– Cell synchronization information reporting indicator	FALSE
– Cell Identity reporting indicator	TRUE
– CPICH Ec/N0 reporting indicator	FALSE
– CPICH RSCP reporting indicator	TRUE
– Pathloss reporting indicator	FALSE
– Reporting quantities for detected set cells	Not Present
– Reporting cell status
– CHOICE reported cell	Report cell within active set and/or monitored cells on used frequency
– Maximum number of reported cells	2
– Measurement validity	Not Present
– CHOICE report criteria	Periodic reporting criteria
– Amount of reporting	Infinity
– Reporting interval	64 s
DPCH Compressed mode status info	Not Present

Contents of MEASUREMENT CONTROL FAILURE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if it’s set to the identical value for the same IE in the downlink MEASUREMENT CONTROL message
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Failure cause	See the test content

Contents of MEASUREMENT REPORT message: AM

Information Element	Value/remark	Version
Message Type
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Measurement identity	1
Measured Results
– Intra-frequency measured results
– Cell measured results
– Cell Identity	Not present
– Cell synchronization information	Checked that this IE is absent
– Primary CPICH info
– Primary scrambling code	Different from the Default setting in clause 6.1 (FDD)
– CPICH Ec/N0	Checked that this IE is absent
– CPICH RSCP	Checked that this IE is present
– Pathloss	Checked that this IE is absent
Measured results on RACH	Checked that this IE is absent
Additional measured results	Checked that this IE is absent
Event results	Checked that this IE is absent
GSM OTD reference cell	Checked that this IE is absent	Rel-4
CSG Proximity Indication	FFS	REL-9
Inter-RAT cell info indication	Checked that this IE is absent	Rel-5

Contents of PAGING TYPE 1 message: TM (Speech in CS)

Information Element	Value/remark
Message Type
Paging record list
– Paging record
– CHOICE Used paging identity	CN identity
– Paging cause	Terminating Conversational Call
– CN domain identity	CS domain
– CHOICE UE identity
– IMSI (GSM-MAP)	Set to the same octet string as in the IMSI stored in the USIM card
BCCH modification info	Not Present
ETWS information	Not Present

Contents of PAGING TYPE 1 message: TM (The others of speech in CS)

Information Element	Value/remark
Message Type
Paging record list
– Paging record
– CHOICE Used paging identity	CN identity
– Paging cause	Terminating Streaming Call
– CN domain identity	CS domain
– CHOICE UE identity
– IMSI (GSM-MAP)	Set to the same octet string as in the IMSI stored in the USIM card
BCCH modification info	Not Present
ETWS information	Not Present

Contents of PAGING TYPE 1 message: TM (Packet in PS)

Information Element	Value/remark
Message Type
Paging record list
– Paging record
– CHOICE Used paging identity	CN identity
– Paging cause	Terminating Interactive Call
– CN domain identity	PS domain
– CHOICE UE identity
– P-TMSI	Use P-TMSI allocated by SS at initial attach.
BCCH modification info	Not Present
ETWS information	Not Present

Contents of PAGING TYPE 1 message: TM (SMS in CS)

Information Element	Value/remark
Message Type
Paging record list
– Paging record
– CHOICE Used paging identity	CN identity
– Paging cause	Terminating Low Priority Signalling
– CN domain identity	CS domain
– CHOICE UE identity
– IMSI (GSM-MAP)	Set to the same octet string as in the IMSI stored in the TEST USIM card
BCCH modification info	Not Present
ETWS information	Not Present

Contents of PAGING TYPE 1 message: TM (SMS in PS)

Information Element	Value/remark
Message Type
Paging record list
– Paging record
– CHOICE Used paging identity	CN identity
– Paging cause	Terminating Low Priority Signalling
– CN domain identity	PS domain
– CHOICE UE identity
– IMSI (GSM-MAP)	Set to the same octet string as in the IMSI stored in the TEST USIM card
BCCH modification info	Not Present
ETWS information	Not Present

Contents of PAGING TYPE 2 message: AM (Speech in CS)

Information Element	Value/remark
Message Type
RRC transaction identifier	Arbitrarily selects an integer between 0 and 3
Integrity check info
– message authentication code	SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC message sequence number	SS provides the value of this IE, from its internal counter.
Paging cause	Terminating Conversational Call
CN domain identity	CS domain
Paging record type identifier	Select the same type as in the IE "Initial UE Identity" in RRC CONNECTION REQUEST" message.

Contents of PHYSICAL CHANNEL RECONFIGURATION message: AM or UM

Information Element	Condition	Value/remark	Version
Message Type	A1, A2, A3, A4, A5, A6, A7, A8, A9, A10
RRC transaction identifier		Arbitrarily selects an integer between 0 and 3
Integrity check info
– message authentication code		SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC message sequence number		SS provides the value of this IE, from its internal counter.
Integrity protection mode info		Not Present
Ciphering mode info		Not Present
Activation time	A1, A2, A3	(256+CFN-(CFN MOD 8 + 8))MOD 256
Activation time	A4, A5, A6, A7, A8, A9, A10	Not Present
Delay restriction flag	A1, A2, A3, A4, A5, A6, A7, A8, A9, A10	Not Present	Rel-6
New U-RNTI		Not Present
New C-RNTI	A1, A2, A3, A4, A7, A8, A9, A10	Not Present
New C-RNTI	A5, A6	‘1010 1010 1010 1010’
New DSCH-RNTI	A1, A2, A3, A4, A5, A6, A7, A8, A9, A10	Not Present	R99 and Rel-4 only
New H-RNTI	A1, A2, A3, A4, A5, A6, A7, A8, A9, A10	Not Present	Rel-5
New Primary E-RNTI		Not Present	Rel-6
New Secondary E-RNTI		Not Present	Rel-6
RRC State indicator	A1, A2, A3, A4	CELL_DCH
RRC State indicator	A5, A6	CELL_FACH
RRC State indicator	A7, A8	URA_PCH
RRC State indicator	A9, A10	CELL_PCH
UE Mobility State Indicator		Not Present	Rel-7
UTRAN DRX cycle length coefficient	A1, A2, A3, A4, A5, A6	Not Present
UTRAN DRX cycle length coefficient	A7, A8, A9, A10	3
CN information info		Not Present
URA identity		Not Present
RNC support for change of UE capability		Not Present	Rel-7
Reconfiguration in response to requested change of UE capability		Not Present	Rel-7
Downlink counter synchronization info		Not Present
Frequency info	A1, A2, A3, A4, A5
– UARFCN uplink (Nu)		Not present Absence of this IE is equivalent to applying the default duplex distance defined for the operating frequency according to 3GPP TS 25.101 [11]
– UARFCN downlink (Nd)		Reference to clause 5.1 Test frequencies
Frequency info	A6, A7, A8, A9, A10	Not Present
DTX-DRX timing information		Not Present	Rel-7
DTX-DRX Information		Not Present	Rel-7
HS-SCCH less Information		Not Present	Rel-7
MIMO parameters		Not Present	Rel-7
HARQ Info		Not Present	Rel-7
Maximum allowed UL TX power		33dBm
CHOICE channel requirement	A5, A6, A7, A8, A9, A10	Not Present
CHOICE channel requirement	A1, A2, A3, A4	Uplink DPCH info
– Uplink DPCH power control info
– DPCCH power offset		-40 (-80dB)
– PC Preamble		1 frame
– SRB delay		7 frames
– Power Control Algorithm		Algorithm1
– TPC step size		0 (1dB)
– ACK		Not Present	Rel-5
– NACK		Not Present	Rel-5
– Ack-Nack repetition factor		Not Present	Rel-5
– HARQ_preamble_mode		0	Rel-6
– Scrambling code type		Long
– Scrambling code number		0 (0 to 16777215)
– Number of DPDCH		Not Present(1)
– spreading factor		Reference to clause 6.10 Parameter Set
– TFCI existence		Reference to clause 6.10 Parameter Set
– Number of FBI bit		Reference to clause 6.10 Parameter Set
– Number of TPC bits		Not Present	Rel-7
– Puncturing Limit		Reference to clause 6.10 Parameter Set
E-DCH Info		Not Present	Rel-6
CHOICE Mode	A1, A2, A3, A4, A5, A6, A7, A8, A9, A10	FDD
– Downlink PDSCH information		Not Present	R99 and Rel-4 only
Downlink HS-PDSCH Information	A1, A2, A3, A4, A5, A6, A7, A8, A9, A10	Not Present	Rel-5
Downlink information common for all radio links	A1, A2, A3
– Downlink DPCH info common for all RL
– Timing indicator		Maintain
– CFN-targetSFN frame offset		Not Present
– Downlink DPCH power control information
– DPC mode		0 (single)
– CHOICE mode		FDD
– Power offset PPilot-DPDCH		0
– DL rate matching restriction information		Not Present
– Spreading factor		Reference to clause 6.10 Parameter Set
– Fixed or Flexible Position		Reference to clause 6.10 Parameter Set
– TFCI existence		Reference to clause 6.10 Parameter Set
– CHOICE SF		Reference to clause 6.10 Parameter Set
– DPCH compressed mode info		Not Present
– TX Diversity mode		None
– SSDT information		Not Present	R99 and Rel-4 only
– Default DPCH Offset Value		Not Present
– MAC-hs reset indicator		Not Present	Rel-5
Downlink information common for all radio links	A4
– Downlink DPCH info common for all RL
– Timing indicator		Initialize
– CFN-targetSFN frame offset		Not Present
– Downlink DPCH power control information
– DPC mode		0 (single)
– CHOICE mode		FDD
– Power offset PPilot-DPDCH		0
– DL rate matching restriction information		Not Present
– Spreading factor		Reference to clause 6.10 Parameter Set
– Fixed or Flexible Position		Reference to clause 6.10 Parameter Set
– TFCI existence		Reference to clause 6.10 Parameter Set
– CHOICE SF		Reference to clause 6.10 Parameter Set
– DPCH compressed mode info		Not Present
– TX Diversity mode		None
– SSDT information		Not Present	R99 and Rel-4 only
– Default DPCH Offset Value		Arbitrary set to value 0..306688 by step of 512
– MAC-hs reset indicator		Not Present	Rel-5
Downlink information common for all radio links	A5, A6, A7, A8, A9, A10	Not Present
Downlink information for each radio links	A1, A2,A3
– Choice mode		FDD
– Primary CPICH info
– Primary scrambling code		Ref. to the Default setting in clause 6.1 (FDD)
– PDSCH with SHO DCH info		Not Present	R99 and Rel-4 only
– PDSCH code mapping		Not Present	R99 and Rel-4 only
– Serving HS-DSCH radio link indicator		FALSE	Rel-5
– Serving E-DCH radio link indicator		FALSE	Rel-6
– Downlink DPCH info for each RL
– CHOICE mode		FDD
– Primary CPICH usage for channel estimation		Primary CPICH may be used
– DPCH frame offset		Set to value : Default DPCH Offset Value (as currently stored in SS) mod 38 400
– Secondary CPICH info		Not Present
– DL channelisation code
– Secondary scrambling code		5
– Spreading factor		Reference to clause 6.10 Parameter Set
– Code number		0
– Scrambling code change		Set to value Default1: No code change (if the UE has a compressed mode pattern sequence configured in variable TGPS_IDENTITY or included in the message including IE "Downlink DPCH info for each RL", which is using compressed mode method "SF/2") Set to value Default2: OMIT (otherwise)
– TPC combination index		0
– SSDT Cell Identity		Not Present	R99 and Rel-4 only
– Closed loop timing adjustment mode		Not Present
– E-AGCH Info		Not Present	Rel-6
– E-HICH Information		Not Present	Rel-6
– E-RGCH Information		Not Present	Rel-6
– SCCPCH information for FACH		Not Present	R99 and Rel-4 only
Downlink information for each radio links	A4
– Choice mode		FDD
– Primary CPICH info
– Primary scrambling code		Ref. to the Default setting in clause 6.1 (FDD)
– PDSCH with SHO DCH info		Not Present	R99 and Rel-4 only
– PDSCH code mapping		Not Present	R99 and Rel-4 only
– Serving HS-DSCH radio link indicator		FALSE	Rel-5
– Serving E-DCH radio link indicator		FALSE	Rel-6
– Downlink DPCH info for each RL
– CHOICE mode		FDD
– Primary CPICH usage for channel estimation		Primary CPICH may be used
– DPCH frame offset		Set to value : Default DPCH Offset Value mod 38 400
– Secondary CPICH info		Not Present
– DL channelisation code
– Secondary scrambling code		5
– Spreading factor		Reference to clause 6.10 Parameter Set
– Code number		0
– Scrambling code change		Set to value Default1: No code change (if the UE has a compressed mode pattern sequence configured in variable TGPS_IDENTITY or included in the message including IE "Downlink DPCH info for each RL", which is using compressed mode method "SF/2") Set to value Default2: OMIT (otherwise)
– TPC combination index		0
– SSDT Cell Identity		Not Present	R99 and Rel-4 only
– Closed loop timing adjustment mode		Not Present
– E-AGCH Info		Not Present	Rel-6
– E-HICH Information		Not Present	Rel-6
– E-RGCH Information		Not Present	Rel-6
– SCCPCH information for FACH		Not Present	R99 and Rel-4 only
– Downlink information for each radio link	A5
– Choice mode		FDD
– Primary CPICH info
– Primary scrambling code		Ref. to the Default setting in clause 6.1 (FDD)
– PDSCH with SHO DCH info		Not Present	R99 and Rel-4 only
– PDSCH code mapping		Not Present	R99 and Rel-4 only
– Serving HS-DSCH radio link indicator		FALSE	Rel-5
– Serving E-DCH radio link indicator		FALSE	Rel-6
– Downlink DPCH info for each RL		Not Present
– E-AGCH Info		Not Present	Rel-6
– E-HICH Information		Not Present	Rel-6
– E-RGCH Information		Not Present	Rel-6
– SCCPCH Information for FACH		Not Present	R99 and Rel-4 only
– Downlink information for each radio link	A6, A7, A8, A9, A10	Not Present
MBMS PL Service Restriction Information	A1, A2, A3, A4, A5, A6, A7, A8, A9, A10	Not Present	Rel-6

Condition	Explanation
A1	This IE need for "Non speech in CS"
A2	This IE need for "Speech in CS"
A3	This IE need for "Packet to CELL_DCH from CELL_DCH in PS"
A4	This IE need for "Packet to CELL_DCH from CELL_FACH in PS"
A5	This IE need for "Packet to CELL_FACH from CELL_DCH in PS"
A6	This IE need for "Packet to CELL_FACH from CELL_FACH in PS"
A7	This IE need for "Packet to URA_PCH from CELL_FACH in PS"
A8	This IE need for "Packet to URA_PCH from CELL_DCH in PS"
A9	This IE need for "Packet to CELL_PCH from CELL_FACH in PS"
A10	This IE need for "Packet to CELL_PCH from CELL_DCH in PS"

Contents of PHYSICAL CHANNEL RECONFIGURATION COMPLETE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if it’s set to identical value of the same IE in the downlink PHYSICAL CHANNEL RECONFIGURATION message
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Uplink integrity protection activation info	Not checked
CHOICE mode	FDD
Deferred measurement control reading	Not present for Rel-7 or later, otherwise Not checked
COUNT-C activation time	Not checked
Radio bearer uplink ciphering activation time info	Not checked
Uplink counter synchronization info	Not present

Contents of PHYSICAL CHANNEL RECONFIGURATION FAILURE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if it is set to identical value of the same IE in the downlink PHYSICAL CHANNEL RECONFIGURATION message.
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Failure cause	Checked to see if it meets test requirement

Contents of RADIO BEARER SETUP message: AM or UM

Information Element			Condition			Value/remark		Version	Index
Message Type			A1, A2, A3, A4, A5, A6, A7, A8, A11						RBS-003
			, A9, A10					Rel-5	RBS-004
			, A12, A13, A14, A15, A16					Rel-6	RBS-005
			, A17, A17a, A17b, A17c, A17d, A17e, A17f, A18, A19, A19a, A19b, A20, A21, A22					Rel-7	RBS-006
			, A23, A24,A28a					Rel-7 Rel-8	RBS-007
			, A25, A25a, A25b, A26, A27, A28, A29, A30					Rel-8	RBS-008
			, A25c, A31, A32 , A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-009
RRC transaction identifier						Arbitrarily selects an integer between 0 and 3			RBS-010
Integrity check info									RBS-011
– message authentication code						SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.			RBS-012
– RRC message sequence number						SS provides the value of this IE, from its internal counter.			RBS-013
Integrity protection mode info						Not Present			RBS-014
Ciphering mode info						Not Present			RBS-015
Sr-vcc-Info						Not Present
Activation time			A1, A2, A3, A11			(256+CFN-(CFN MOD 8 + 8)) MOD 256			RBS-016
			, A9					Rel-5	RBS-017
			, A12, A13, A14, A15, A16					Rel-6	RBS-018
			, A17, A17a, A17b, A17d, A17e, A17f, A18, A19, A19a, A19b, A20, A21, A22					Rel-7	RBS-019
			, A23, A28a					Rel-7 Rel-8	RBS-020
			, A25, A25a, A25b, A26, A27, A27a, A28					Rel-8	RBS-021
			, A25c, A31, A32 , A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-021b
Activation time			A4, A5, A6, A7, A8			Not Present			RBS-022
Activation time			A10, A24			Not Present		Rel-5	RBS-023
			, A29, A30					Rel-8	RBS-024
New U-RNTI			A1, A2, A3, A4, A5, A6, A7, A8, A11			Not Present			RBS-026
			, A9, A10					Rel-5	RBS-027
			, A12, A13, A14, A15, A16					Rel-6	RBS-028
			, A17, A17a, A17b, A17c, A17d, A17e, A17f, A18, A19, A19a, A19b, A20, A21, A22, A24					Rel-7	RBS-029
			, A23, A28a					Rel-7 Rel-8	RBS-030
			, A25, A25a, A25b, A26, A27, A27a, A28, A29, A30					Rel-8	RBS-031
			, A25c, A31, A32 , A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-032
New C-RNTI			A1, A2, A3, A4, A7, A8, A11			Not Present			RBS-033
			, A9, A10					Rel-5	RBS-034
			, A12, A13, A14, A15, A16					Rel-6	RBS-035
			, A17, A17a, A17b, A17c, A17d, A17e, A17f, A18, A19, A19a, A19b, A20, A21, A22, A24					Rel-7	RBS-036
			, A23, A28a					Rel-7 Rel-8	RBS-037
			, A25, A25a, A25b, A26, A27, A27a, A28, A29, A30					Rel-8	RBS-038
			, A25c, A31, A32 , A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-039
New C-RNTI			A5, A6			‘1010 1010 1010 1010’			RBS-040
New DSCH-RNTI			A1, A2, A3, A4, A5, A6, A7, A8, A11			Not Present		R99 and Rel-4 only	RBS-041
New H-RNTI			A1, A2, A3, A4, A5, A6, A7, A8, A11			Not Present		Rel-5	RBS-042
New H-RNTI			A9, A10			‘1010 1010 1010 1010’		Rel-5	RBS-045
New H-RNTI			A12, A13, A14, A15, A16			‘1010 1010 1010 1010’		Rel-6	RBS-046
			, A17, A17a, A17b, A17c, A17d, A17e, A17f, A18, A19, A19a, A19b, A20, A21, A22, A24					Rel-7	RBS-047
			, A23, A28a					Rel-7 Rel-8	RBS-048
			, A25, A25a, A25b, A26, A27, A27a, A28					Rel-8	RBS-049
			, A25c, A29, A30, A31, A32 , A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-049b
New Primary E-RNTI			A1, A2, A3, A4, A5, A6, A7, A8, A9, A10, A11			Not Present		Rel-6	RBS-050
			, A17, A17a, A18, A24					Rel-7	RBS-051
			, A25a, A28					Rel-8	RBS-052
New Primary E-RNTI			A12, A13, A14, A15, A16, A17b, A17c, A17d, A17e A17f,			‘1010 1010 1010 1010’		Rel-6	RBS-054
			, A19, A19a, A19b, A20, A21, A22					Rel-7	RBS-055
			, A23, A28a					Rel-7 Rel-8	RBS-056
			, A25, A25b, A26, A27, A27a, A29, A30					Rel-8	RBS-057
			A25c, A31, A32 , A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-057b
New Secondary E-RNTI			A1, A2, A3, A4, A5, A6, A7, A8, A9, A10, A11, A12, A13, A14, A15, A16			Not Present		Rel-6	RBS-058
			, A17, A17a, A17b, A17c, A17d, A17e, A17f, A18, A19, A19a, A19b, A20, A21, A22, A24					Rel-7	RBS-059
			, A23, A28a					Rel-7 Rel-8	RBS-060
			, A25, A25a, A25b, A26, A27, A27a, A28, A29, A30					Rel-8	RBS-061
			, A31, A32 , A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-062
RRC State indicator			A1, A2, A3, A4, A7, A8, A11			CELL_DCH			RBS-063
			, A9, A10					Rel-5	RBS-064
			, A12, A13, A14, A15, A16					Rel-6	RBS-065
			, A17, A17a, A17b, A17c, A17d, A17e, A17f, A18, A19, A19a, A19b, A20, A21, A22					Rel-7	RBS-066
			, A23, A28a					Rel-7 Rel-8	RBS-067
			, A25, A25a, A25b, A26, A27, A27a, A28, A30					Rel-8	RBS-068
			, A25c, A31, A32 , A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-069
RRC State indicator			A5, A6,			CELL_FACH			RBS-070
			A24					Rel-7	RBS-071
			A29						RBS-072
UTRAN DRX cycle length coefficient			A1, A2, A3, A4, A5, A6, A7, A8, A11			Not Present			RBS-073
			, A9, A10					Rel-5	RBS-074
			, A12, A13, A14, A15, A16					Rel-6	RBS-075
			, A17, A17a, A17b, A17c, A17d, A17e, A17f, A18, A19, A19a, A19b, A20, A21, A22, A24					Rel-7	RBS-076
			, A23, A28a					Rel-7 Rel-8	RBS-077
			, A25, A25a, A25b, A26, A27, A27a, A28, A29, A30					Rel-8	RBS-078
			, A25c, A31, A32 , A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-079
CN information info						Not Present			RBS-080
URA identity						Not Present			RBS-081
RNC support for change of UE capability						Not Present		Rel-7	RBS-082
CHOICE Specification mode						Complete specification		Rel-6	RBS-083
– Signalling RB information to setup						Not Present			RBS-084
– RAB information for setup			A1, A7						RBS-085
– RAB info									RBS-086
– RAB identity						0000 0001B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-087
– CN domain identity						CS domain			RBS-088
– NAS Synchronization Indicator						Not Present			RBS-089
– Re-establishment timer						useT314			RBS-090
– RB information to setup									RBS-091
– RB identity						10			RBS-092
– PDCP info						Not Present			RBS-093
– CHOICE RLC info type						RLC info			RBS-094
– CHOICE Uplink RLC mode						TM RLC			RBS-095
– Transmission RLC discard						Not Present			RBS-096
– Segmentation indication						FALSE			RBS-097
– CHOICE Downlink RLC mode						TM RLC			RBS-098
– Segmentation indication						FALSE			RBS-099
– RB mapping info									RBS-100
– Information for each multiplexing option									RBS-101
– RLC logical channel mapping indicator						Not Present			RBS-102
– Number of uplink RLC logical channels						1			RBS-103
– Uplink transport channel type						DCH			RBS-104
– UL Transport channel identity						1			RBS-105
– Logical channel identity						Not Present			RBS-106
– CHOICE RLC size list						Configured			RBS-107
– MAC logical channel priority						7			RBS-108
– Downlink RLC logical channel info									RBS-109
– Number of downlink RLC logical channels						1			RBS-110
– Downlink transport channel type						DCH			RBS-111
– DL DCH Transport channel identity						6			RBS-112
– DL DSCH Transport channel identity						Not Present			RBS-113
– Logical channel identity						Not Present			RBS-114
– RAB information for setup			A2, A8						RBS-115
– RAB info									RBS-116
– RAB identity						0000 0001B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-117
– CN domain identity						CS domain			RBS-118
– NAS Synchronization Indicator						Not Present			RBS-119
– Re-establishment timer						useT314			RBS-120
– RB information to setup									RBS-121
– RB identity						10			RBS-122
– PDCP info						Not Present			RBS-123
– CHOICE RLC info type						RLC info			RBS-124
– CHOICE Uplink RLC mode						TM RLC			RBS-125
– Transmission RLC discard						Not Present			RBS-126
– Segmentation indication						FALSE			RBS-127
– CHOICE Downlink RLC mode						TM RLC			RBS-128
– Segmentation indication						FALSE			RBS-129
– RB mapping info									RBS-130
– Information for each multiplexing option									RBS-131
– RLC logical channel mapping indicator						Not Present			RBS-132
– Number of uplink RLC logical channels						1			RBS-133
– Uplink transport channel type						DCH			RBS-134
– UL Transport channel identity						1			RBS-135
– Logical channel identity						Not Present			RBS-136
– CHOICE RLC size list						Configured			RBS-137
– MAC logical channel priority						6			RBS-138
– Downlink RLC logical channel info									RBS-139
– Number of downlink RLC logical channels						1			RBS-140
– Downlink transport channel type						DCH			RBS-141
– DL DCH Transport channel identity						6			RBS-142
– DL DSCH Transport channel identity						Not Present			RBS-143
– Logical channel identity						Not Present			RBS-144
– RB identity						11			RBS-145
– PDCP info						Not Present			RBS-146
– CHOICE RLC info type						RLC info			RBS-147
– CHOICE Uplink RLC mode						TM RLC			RBS-148
– Transmission RLC discard						Not Present			RBS-149
– Segmentation indication						FALSE			RBS-150
– CHOICE Downlink RLC mode						TM RLC			RBS-151
– Segmentation indication						FALSE			RBS-152
– RB mapping info									RBS-153
– Information for each multiplexing option									RBS-154
– RLC logical channel mapping indicator						Not Present			RBS-155
– Number of uplink RLC logical channels						1			RBS-156
– Uplink transport channel type						DCH			RBS-157
– UL Transport channel identity						2			RBS-158
– Logical channel identity						Not Present			RBS-159
– CHOICE RLC size list						Configured			RBS-160
– MAC logical channel priority						6			RBS-161
– Downlink RLC logical channel info									RBS-162
– Number of downlink RLC logical channels						1			RBS-163
– Downlink transport channel type						DCH			RBS-164
– DL DCH Transport channel identity						7			RBS-165
– DL DSCH Transport channel identity						Not Present			RBS-166
– Logical channel identity						Not Present			RBS-167
– RB identity						12			RBS-168
– PDCP info						Not Present			RBS-169
– CHOICE RLC info type						RLC info			RBS-170
– CHOICE Uplink RLC mode						TM RLC			RBS-171
– Transmission RLC discard						Not Present			RBS-172
– Segmentation indication						FALSE			RBS-173
– CHOICE Downlink RLC mode						TM RLC			RBS-174
– Segmentation indication						FALSE			RBS-175
– RB mapping info									RBS-176
– Information for each multiplexing option									RBS-177
– RLC logical channel mapping indicator						Not Present			RBS-178
– Number of uplink RLC logical channels						1			RBS-179
– Uplink transport channel type						DCH			RBS-180
– UL Transport channel identity						3			RBS-181
– Logical channel identity						Not Present			RBS-182
– CHOICE RLC size list						Configured			RBS-183
– MAC logical channel priority						6			RBS-184
– Downlink RLC logical channel info									RBS-185
– Number of downlink RLC logical channels						1			RBS-186
– Downlink transport channel type						DCH			RBS-187
– DL DCH Transport channel identity						8			RBS-188
– DL DSCH Transport channel identity						Not Present			RBS-189
– Logical channel identity						Not Present			RBS-190
– RAB information for setup			A3, A4, A5, A6						RBS-191
– RAB info						(AM DTCH for PS domain)			RBS-192
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-193
– CN domain identity						PS domain			RBS-194
– NAS Synchronization Indicator						Not Present			RBS-195
– Re-establishment timer						useT315			RBS-196
– RB information to setup									RBS-197
– RB identity						20			RBS-198
– PDCP info									RBS-199
– Support for lossless SRNS relocation						FALSE			RBS-200
– Max PDCP SN window size						Not present			RBS-201
– PDCP PDU header						Absent			RBS-202
– Header compression information						Not present			RBS-203
– CHOICE RLC info type						RLC info			RBS-204
– CHOICE Uplink RLC mode						AM RLC			RBS-205
– Transmission RLC discard									RBS-206
– CHOICE SDU discard mode						No Discard			RBS-207
– MAX_DAT						15			RBS-208
– Transmission window size						128			RBS-209
– Timer_RST						500			RBS-210
– Max_RST						4			RBS-211
– Polling info									RBS-212
– Timer_poll_prohibit						200			RBS-213
– Timer_poll						200			RBS-214
– Poll_PDU						Not Present			RBS-215
– Poll_SDU						1			RBS-216
– Last transmission PDU poll						TRUE			RBS-217
– Last retransmission PDU poll						TRUE			RBS-218
– Poll_Windows						99			RBS-219
– Timer_poll_periodic						Not Present			RBS-220
– CHOICE Downlink RLC mode						AM RLC			RBS-221
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set		Rel-5	RBS-222
– In-sequence delivery						TRUE			RBS-223
– Receiving window size						128			RBS-224
– Downlink RLC status info									RBS-225
– Timer_status_prohibit						200			RBS-226
– Timer_EPC						Not Present			RBS-227
– Missing PDU indicator						TRUE			RBS-228
– Timer_STATUS_periodic						Not Present			RBS-229
– RB mapping info									RBS-230
– Information for each multiplexing option						2 RBMuxOptions			RBS-231
– RLC logical channel mapping indicator						Not Present			RBS-232
– Number of uplink RLC logical channels						1			RBS-233
– Uplink transport channel type						DCH			RBS-234
– UL Transport channel identity						1			RBS-235
– Logical channel identity						Not Present			RBS-236
– CHOICE RLC size list						Configured			RBS-237
– MAC logical channel priority						8			RBS-238
– Downlink RLC logical channel info									RBS-239
– Number of downlink RLC logical channels						1			RBS-240
– Downlink transport channel type						DCH			RBS-241
– DL DCH Transport channel identity						6			RBS-242
– DL DSCH Transport channel identity						Not Present			RBS-243
– Logical channel identity						Not Present			RBS-244
– RLC logical channel mapping indicator						Not Present			RBS-245
– Number of uplink RLC logical channels						1			RBS-246
– Uplink transport channel type						RACH			RBS-247
– UL Transport channel identity						Not Present			RBS-248
– Logical channel identity						7			RBS-249
– CHOICE RLC size list						Explicit list			RBS-250
– RLC size index						Reference to clause 6 Parameter Set			RBS-251
– MAC logical channel priority						8			RBS-252
– Downlink RLC logical channel info									RBS-253
– Number of downlink RLC logical channels						1			RBS-254
– Downlink transport channel type						FACH			RBS-255
– DL DCH Transport channel identity						Not Present			RBS-256
– DL DSCH Transport channel identity						Not Present			RBS-257
– Logical channel identity						7			RBS-258
– RAB information for setup			A9					Rel-5	RBS-259
– RAB info						(high-speed AM DTCH for PS domain)			RBS-260
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-261
– CN domain identity						PS domain			RBS-262
– NAS Synchronization Indicator						Not Present			RBS-263
– Re-establishment timer						useT315			RBS-264
– RB information to setup									RBS-265
– RB identity						25			RBS-266
– PDCP info									RBS-267
– Support for lossless SRNS relocation						FALSE			RBS-268
– Max PDCP SN window size						Not present			RBS-269
– PDCP PDU header						Absent			RBS-270
– Header compression information						Not present			RBS-271
– CHOICE RLC info type						RLC info			RBS-272
– CHOICE Uplink RLC mode						AM RLC			RBS-273
– Transmission RLC discard									RBS-274
– CHOICE SDU discard mode						No Discard			RBS-275
– MAX_DAT						15			RBS-276
– Transmission window size						128			RBS-277
– Timer_RST						500			RBS-278
– Max_RST						4			RBS-279
– Polling info									RBS-280
– Timer_poll_prohibit						100			RBS-281
– Timer_poll						100			RBS-282
– Poll_PDU						Not Present			RBS-283
– Poll_SDU						1			RBS-284
– Last transmission PDU poll						TRUE			RBS-285
– Last retransmission PDU poll						TRUE			RBS-286
– Poll_Windows						99			RBS-287
– Timer_poll_periodic						Not Present			RBS-288
– CHOICE Downlink RLC mode						AM RLC			RBS-289
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set			RBS-290
– In-sequence delivery						TRUE			RBS-291
– Receiving window size						768			RBS-292
– Downlink RLC status info									RBS-293
– Timer_status_prohibit						100			RBS-294
– Timer_EPC						Not Present			RBS-295
– Missing PDU indicator						TRUE			RBS-296
– Timer_STATUS_periodic						Not Present			RBS-297
– One sided RLC re-establishment						FALSE			RBS-298
– RB mapping info									RBS-299
– Information for each multiplexing option						3 RBMuxOptions			RBS-300
– RLC logical channel mapping indicator						Not Present			RBS-301
– Number of uplink RLC logical channels						1			RBS-302
– Uplink transport channel type						DCH			RBS-303
– UL Transport channel identity						1			RBS-304
– Logical channel identity						Not Present			RBS-305
– CHOICE RLC size list						Configured			RBS-306
– MAC logical channel priority						8			RBS-307
– Downlink RLC logical channel info									RBS-308
– Number of downlink RLC logical channels						1			RBS-309
– Downlink transport channel type						DCH			RBS-310
– DL DCH Transport channel identity						6			RBS-311
– DL DSCH Transport channel identity						Not Present			RBS-312
– DL HS-DSCH MAC-d flow identity						Not Present			RBS-313
– Logical channel identity						Not Present			RBS-314
– RLC logical channel mapping indicator						Not Present			RBS-315
– Number of uplink RLC logical channels						1			RBS-316
– Uplink transport channel type						DCH			RBS-317
– UL Transport channel identity						1			RBS-318
– Logical channel identity						Not Present			RBS-319
– CHOICE RLC size list						Configured			RBS-320
– MAC logical channel priority						8			RBS-321
– Downlink RLC logical channel info									RBS-322
– Number of downlink RLC logical channels						1			RBS-323
– Downlink transport channel type						HS-DSCH			RBS-324
– DL DCH Transport channel identity						Not Present			RBS-325
– DL DSCH Transport channel identity						Not Present			RBS-326
– DL HS-DSCH MAC-d flow identity						0			RBS-327
– Logical channel identity						Not Present			RBS-328
– RLC logical channel mapping indicator						Not Present			RBS-329
– Number of uplink RLC logical channels						1			RBS-330
– Uplink transport channel type						RACH			RBS-331
– UL Transport channel identity						Not Present			RBS-332
– Logical channel identity						7			RBS-333
– CHOICE RLC size list						Explicit list			RBS-334
– RLC size index						Reference to clause 6 Parameter Set			RBS-335
– MAC logical channel priority						8			RBS-336
– Downlink RLC logical channel info									RBS-337
– Number of downlink RLC logical channels						1			RBS-338
– Downlink transport channel type						FACH			RBS-339
– DL DCH Transport channel identity						Not Present			RBS-340
– DL DSCH Transport channel identity						Not Present			RBS-341
– Logical channel identity						7			RBS-342
– RAB information for setup			A10					Rel-5	RBS-343
– RAB info						(high-speed AM DTCH for PS domain)			RBS-344
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-345
– CN domain identity						PS domain			RBS-346
– NAS Synchronization Indicator						Not Present			RBS-347
– Re-establishment timer						useT315			RBS-348
– RB information to setup									RBS-349
– RB identity						25			RBS-350
– PDCP info									RBS-351
– Support for lossless SRNS relocation						FALSE			RBS-352
– Max PDCP SN window size						Not present			RBS-353
– PDCP PDU header						Absent			RBS-354
– Header compression information						Not present			RBS-355
– CHOICE RLC info type						RLC info			RBS-356
– CHOICE Uplink RLC mode						AM RLC			RBS-357
– Transmission RLC discard									RBS-358
– CHOICE SDU discard mode						No Discard			RBS-359
– MAX_DAT						15			RBS-360
– Transmission window size						128			RBS-361
– Timer_RST						500			RBS-362
– Max_RST						4			RBS-363
– Polling info									RBS-364
– Timer_poll_prohibit						100			RBS-365
– Timer_poll						100			RBS-366
– Poll_PDU						Not Present			RBS-367
– Poll_SDU						1			RBS-368
– Last transmission PDU poll						TRUE			RBS-369
– Last retransmission PDU poll						TRUE			RBS-370
– Poll_Windows						99			RBS-371
– Timer_poll_periodic						Not Present			RBS-372
– CHOICE Downlink RLC mode						AM RLC			RBS-373
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set			RBS-374
– In-sequence delivery						TRUE			RBS-375
– Receiving window size						768			RBS-376
– Downlink RLC status info									RBS-377
– Timer_status_prohibit						100			RBS-378
– Timer_EPC						Not Present			RBS-379
– Missing PDU indicator						TRUE			RBS-380
– Timer_STATUS_periodic						Not Present			RBS-381
– One sided RLC re-establishment						FALSE			RBS-382
– RB mapping info									RBS-383
– Information for each multiplexing option						1 RBMuxOption			RBS-384
– RLC logical channel mapping indicator						Not present			RBS-385
– Number of uplink RLC logical channels						1			RBS-386
– Uplink transport channel type						DCH			RBS-387
– UL Transport channel identity						1			RBS-388
– Logical channel identity						Not Present			RBS-389
– CHOICE RLC size list						Configured			RBS-390
– MAC logical channel priority						8			RBS-391
– Downlink RLC logical channel info									RBS-392
– Number of downlink RLC logical channels						1			RBS-393
– Downlink transport channel type						HS-DSCH			RBS-394
– DL DCH Transport channel identity						Not present			RBS-395
– DL DSCH Transport channel identity						Not present			RBS-396
– DL HS-DSCH MAC-d flow identity						0			RBS-397
– Logical channel identity						Not Present			RBS-398
– RAB information for setup			A11						RBS-399
– RAB info						(AM DTCH for PS domain)			RBS-400
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-401
– CN domain identity						PS domain			RBS-402
– NAS Synchronization Indicator						Not Present			RBS-403
– Re-establishment timer						useT315			RBS-404
– RB information to setup									RBS-405
– RB identity						20			RBS-406
– PDCP info									RBS-407
– Support for lossless SRNS relocation						FALSE			RBS-408
– Max PDCP SN window size						Not present			RBS-409
– PDCP PDU header						Absent			RBS-410
– Header compression information						Not present			RBS-411
– CHOICE RLC info type						RLC info			RBS-412
– CHOICE Uplink RLC mode						AM RLC			RBS-413
– Transmission RLC discard									RBS-414
– CHOICE SDU discard mode						No Discard			RBS-415
– MAX_DAT						15			RBS-416
– Transmission window size						128			RBS-417
– Timer_RST						500			RBS-418
– Max_RST						4			RBS-419
– Polling info									RBS-420
– Timer_poll_prohibit						200			RBS-421
– Timer_poll						200			RBS-422
– Poll_PDU						Not Present			RBS-423
– Poll_SDU						1			RBS-424
– Last transmission PDU poll						TRUE			RBS-425
– Last retransmission PDU poll						TRUE			RBS-426
– Poll_Windows						99			RBS-427
– Timer_poll_periodic						Not Present			RBS-428
– CHOICE Downlink RLC mode						AM RLC			RBS-429
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set		Rel-5	RBS-430
– In-sequence delivery						TRUE			RBS-431
– Receiving window size						128			RBS-432
– Downlink RLC status info									RBS-433
– Timer_status_prohibit						200			RBS-434
– Timer_EPC						Not Present			RBS-435
– Missing PDU indicator						TRUE			RBS-436
– Timer_STATUS_periodic						Not Present			RBS-437
– RB mapping info									RBS-438
– Information for each multiplexing option						2 RBMuxOptions			RBS-439
– RLC logical channel mapping indicator						Not Present			RBS-440
– Number of uplink RLC logical channels						1			RBS-441
– Uplink transport channel type						DCH			RBS-442
– UL Transport channel identity						4			RBS-443
– Logical channel identity						Not Present			RBS-444
– CHOICE RLC size list						Configured			RBS-445
– MAC logical channel priority						8			RBS-446
– Downlink RLC logical channel info									RBS-447
– Number of downlink RLC logical channels						1			RBS-448
– Downlink transport channel type						DCH			RBS-449
– DL DCH Transport channel identity						9			RBS-450
– DL DSCH Transport channel identity						Not Present			RBS-451
– Logical channel identity						Not Present			RBS-452
– RLC logical channel mapping indicator						Not Present			RBS-453
– Number of uplink RLC logical channels						1			RBS-454
– Uplink transport channel type						RACH			RBS-455
– UL Transport channel identity						Not Present			RBS-456
– Logical channel identity						7			RBS-457
– CHOICE RLC size list						Explicit list			RBS-458
– RLC size index						Reference to clause 6 Parameter Set			RBS-459
– MAC logical channel priority						8			RBS-460
– Downlink RLC logical channel info									RBS-461
– Number of downlink RLC logical channels						1			RBS-462
– Downlink transport channel type						FACH			RBS-463
– DL DCH Transport channel identity						Not Present			RBS-464
– DL DSCH Transport channel identity						Not Present			RBS-465
– Logical channel identity						7			RBS-466
– RAB information for setup			A12					Rel-6	RBS-467
			A19					Rel-7	RBS-468
– RAB info						(high-speed AM DTCH for PS domain)			RBS-469
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-470
– CN domain identity						PS domain			RBS-471
– NAS Synchronization Indicator						Not Present			RBS-472
– Re-establishment timer						useT315			RBS-473
– RB information to setup									RBS-474
– RB identity						25			RBS-475
– PDCP info									RBS-476
– Support for lossless SRNS relocation						FALSE			RBS-477
– Max PDCP SN window size						Not present			RBS-478
– PDCP PDU header						Absent			RBS-479
– Header compression information						Not present			RBS-480
– CHOICE RLC info type						RLC info			RBS-481
– CHOICE Uplink RLC mode						AM RLC			RBS-482
– Transmission RLC discard									RBS-483
– CHOICE SDU discard mode						No Discard			RBS-484
– MAX_DAT						15			RBS-485
– Transmission window size						256			RBS-486
– Timer_RST						500			RBS-487
– Max_RST						4			RBS-488
– Polling info									RBS-489
– Timer_poll_prohibit						100			RBS-490
– Timer_poll						100			RBS-491
– Poll_PDU						Not Present			RBS-492
– Poll_SDU						1			RBS-493
– Last transmission PDU poll						TRUE			RBS-494
– Last retransmission PDU poll						TRUE			RBS-495
– Poll_Windows						99			RBS-496
– Timer_poll_periodic						Not Present			RBS-497
– CHOICE Downlink RLC mode						AM RLC			RBS-498
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set			RBS-499
– In-sequence delivery						TRUE			RBS-500
– Receiving window size						768			RBS-501
– Downlink RLC status info									RBS-502
– Timer_status_prohibit						100			RBS-503
– Timer_EPC						Not Present			RBS-504
– Missing PDU indicator						TRUE			RBS-505
– Timer_STATUS_periodic						Not Present			RBS-506
– One sided RLC re-establishment						FALSE			RBS-507
– RB mapping info									RBS-508
– Information for each multiplexing option						3 RBMuxOptions			RBS-509
– RLC logical channel mapping indicator						Not Present			RBS-510
– Number of uplink RLC logical channels						1			RBS-511
– Uplink transport channel type						DCH			RBS-512
– UL Transport channel identity						1			RBS-513
– Logical channel identity						Not Present			RBS-514
– CHOICE RLC size list						Configured			RBS-515
– MAC logical channel priority						8			RBS-516
– Downlink RLC logical channel info									RBS-517
– Number of downlink RLC logical channels						1			RBS-518
– Downlink transport channel type						DCH			RBS-519
– DL DCH Transport channel identity						6			RBS-520
– DL DSCH Transport channel identity						Not Present			RBS-521
– DL HS-DSCH MAC-d flow identity						Not Present			RBS-522
– Logical channel identity						Not Present			RBS-523
– RLC logical channel mapping indicator						Not Present			RBS-524
– Number of uplink RLC logical channels						1			RBS-525
– Uplink transport channel type						E-DCH			RBS-526
– Logical channel identity						7			RBS-527
– E-DCH MAC-d flow identity						2			RBS-528
– CHOICE RLC PDU size			MAC-I-FIXED			Fixed size		Rel-8	RBS-529
– DDI						5			RBS-530
– RLC PDU size list						1 RLC PDU size			RBS-531
– RLC PDU size						336 bits			RBS-532
– CHOICE RLC PDU size			MAC-I-FLEX			Flexible size		Rel-8	RBS-533
– Length indicator size						15 bit			RBS-534
– Minimum UL RLC PDU size						See clause 6.10			RBS-535
– Largest UL RLC PDU size						See clause 6.10			RBS-536
– Include in scheduling info						TRUE			RBS-537
– MAC logical channel priority						8			RBS-538
– Downlink RLC logical channel info									RBS-539
– Number of downlink RLC logical channels						1			RBS-540
– Downlink transport channel type						HS-DSCH			RBS-541
– DL DCH Transport channel identity						Not Present			RBS-542
– DL DSCH Transport channel identity						Not Present			RBS-543
– DL HS-DSCH MAC-d flow identity						0			RBS-544
– Logical channel identity						Not Present			RBS-545
– RLC logical channel mapping indicator						Not Present			RBS-546
– Number of uplink RLC logical channels						1			RBS-547
– Uplink transport channel type						RACH			RBS-548
– UL Transport channel identity						Not Present			RBS-549
– Logical channel identity						7			RBS-550
– CHOICE RLC size list						Explicit list			RBS-551
– RLC size index						Reference to clause 6 Parameter Set			RBS-552
– MAC logical channel priority						8			RBS-553
– Downlink RLC logical channel info									RBS-554
– Number of downlink RLC logical channels						1			RBS-555
– Downlink transport channel type						FACH			RBS-556
– DL DCH Transport channel identity						Not Present			RBS-557
– DL DSCH Transport channel identity						Not Present			RBS-558
– RAB information for setup			A13, A14, A15, A16					Rel-6	RBS-559
			, A19a, A19b					Rel-7	RBS-560
– RAB info						(high-speed AM DTCH for PS domain)			RBS-561
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-562
– CN domain identity						PS domain			RBS-563
– NAS Synchronization Indicator						Not Present			RBS-564
– Re-establishment timer						useT315			RBS-565
– RB information to setup									RBS-566
– RB identity						25			RBS-567
– PDCP info									RBS-568
– Support for lossless SRNS relocation						FALSE			RBS-569
– Max PDCP SN window size						Not present			RBS-570
– PDCP PDU header						Absent			RBS-571
– Header compression information						Not present			RBS-572
– CHOICE RLC info type						RLC info			RBS-573
– CHOICE Uplink RLC mode						AM RLC			RBS-574
– Transmission RLC discard									RBS-575
– CHOICE SDU discard mode						No Discard			RBS-576
– MAX_DAT						15			RBS-577
– Transmission window size						256			RBS-578
– Timer_RST						500			RBS-579
– Max_RST						4			RBS-580
– Polling info									RBS-581
– Timer_poll_prohibit						100			RBS-582
– Timer_poll						100			RBS-583
– Poll_PDU						Not Present			RBS-584
– Poll_SDU						1			RBS-585
– Last transmission PDU poll						TRUE			RBS-586
– Last retransmission PDU poll						TRUE			RBS-587
– Poll_Windows						99			RBS-588
– Timer_poll_periodic						Not Present			RBS-589
– CHOICE Downlink RLC mode						AM RLC			RBS-590
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set			RBS-591
– In-sequence delivery						TRUE			RBS-592
– Receiving window size						768			RBS-593
– Downlink RLC status info									RBS-594
– Timer_status_prohibit						100			RBS-595
– Timer_EPC						Not Present			RBS-596
– Missing PDU indicator						TRUE			RBS-597
– Timer_STATUS_periodic						Not Present			RBS-598
– One sided RLC re-establishment						FALSE			RBS-599
– RB mapping info									RBS-600
– Information for each multiplexing option						1 RBMuxOption			RBS-601
– RLC logical channel mapping indicator						Not Present			RBS-602
– Number of uplink RLC logical channels						1			RBS-603
– Uplink transport channel type						E-DCH			RBS-604
– Logical channel identity						7			RBS-605
– E-DCH MAC-d flow identity						2			RBS-606
– CHOICE RLC PDU size			MAC-I-FIXED			Fixed size		Rel-8	RBS-607
– DDI						5			RBS-608
– RLC PDU size list						1 RLC PDU size			RBS-609
– RLC PDU size						336 bits			RBS-610
– CHOICE RLC PDU size			MAC-I-FLEX			Flexible size		Rel-8	RBS-611
– Length indicator size						– 15 bit			RBS-612
– Minimum UL RLC PDU size						See clause 6.10			RBS-613
– Largest UL RLC PDU size						See clause 6.10			RBS-614
– Include in scheduling info						TRUE			RBS-615
– MAC logical channel priority						8			RBS-616
– Downlink RLC logical channel info									RBS-617
– Number of downlink RLC logical channels						1			RBS-618
– Downlink transport channel type						HS-DSCH			RBS-619
– DL DCH Transport channel identity						Not present			RBS-620
– DL DSCH Transport channel identity						Not present			RBS-621
– DL HS-DSCH MAC-d flow identity						0			RBS-622
– Logical channel identity						Not Present			RBS-623
– RAB information for setup			A15					Rel-6	RBS-624
– RAB info						(second high-speed AM DTCH for PS domain)			RBS-625
– RAB identity						0000 0110B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-626
– CN domain identity						PS domain			RBS-627
– NAS Synchronization Indicator						Not Present			RBS-628
– Re-establishment timer						useT315			RBS-629
– RB information to setup									RBS-630
– RB identity						17			RBS-631
– PDCP info									RBS-632
– Support for lossless SRNS relocation						FALSE			RBS-633
– Max PDCP SN window size						Not present			RBS-634
– PDCP PDU header						Absent			RBS-635
– Header compression information						Not present			RBS-636
– CHOICE RLC info type						RLC info			RBS-637
– CHOICE Uplink RLC mode						AM RLC			RBS-638
– Transmission RLC discard									RBS-639
– CHOICE SDU discard mode						No Discard			RBS-640
– MAX_DAT						15			RBS-641
– Transmission window size						256			RBS-642
– Timer_RST						500			RBS-643
– Max_RST						4			RBS-644
– Polling info									RBS-645
– Timer_poll_prohibit						100			RBS-646
– Timer_poll						100			RBS-647
– Poll_PDU						Not Present			RBS-648
– Poll_SDU						1			RBS-649
– Last transmission PDU poll						TRUE			RBS-650
– Last retransmission PDU poll						TRUE			RBS-651
– Poll_Windows						99			RBS-652
– Timer_poll_periodic						Not Present			RBS-653
– CHOICE Downlink RLC mode						AM RLC			RBS-654
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set			RBS-655
– In-sequence delivery						TRUE			RBS-656
– Receiving window size						768			RBS-657
– Downlink RLC status info									RBS-658
– Timer_status_prohibit						100			RBS-659
– Timer_EPC						Not Present			RBS-660
– Missing PDU indicator						TRUE			RBS-661
– Timer_STATUS_periodic						Not Present			RBS-662
– One sided RLC re-establishment						FALSE			RBS-663
– RB mapping info									RBS-664
– Information for each multiplexing option						1 RBMuxOption			RBS-665
– RLC logical channel mapping indicator						Not Present			RBS-666
– Number of uplink RLC logical channels						1			RBS-667
– Uplink transport channel type						E-DCH			RBS-668
– Logical channel identity						8			RBS-669
– E-DCH MAC-d flow identity						3			RBS-670
– CHOICE RLC PDU size			MAC-I-FIXED			Fixed size		Rel-8	RBS-671
– DDI						6			RBS-672
– RLC PDU size list						1 RLC PDU size			RBS-673
– RLC PDU size						336 bits			RBS-674
– CHOICE RLC PDU size			MAC-I-FLEX			Flexible size		Rel-8	RBS-675
– Length indicator size						– 15 bit			RBS-676
– Minimum UL RLC PDU size						See clause 6.10			RBS-677
– Largest UL RLC PDU size						See clause 6.10			RBS-678
– Include in scheduling info						TRUE			RBS-679
– MAC logical channel priority						8			RBS-680
– Downlink RLC logical channel info									RBS-681
– Number of downlink RLC logical channels						1			RBS-682
– Downlink transport channel type						HS-DSCH			RBS-683
– DL DCH Transport channel identity						Not present			RBS-684
– DL DSCH Transport channel identity						Not present			RBS-685
– DL HS-DSCH MAC-d flow identity						2			RBS-686
– Logical channel identity						Not Present			RBS-687
– RAB information for setup			A16 , A19b					Rel-6 Rel-7	RBS-688
– RAB info						(Conversational UM DTCH for PS domain)			RBS-689
– RAB identity						0000 0110B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-690
– CN domain identity						PS domain			RBS-691
– NAS Synchronization Indicator						Not Present			RBS-692
– Re-establishment timer						useT314			RBS-693
– RB information to setup									RBS-694
– RB identity						27			RBS-695
– PDCP info									RBS-696
– Support for lossless SRNS relocation						FALSE			RBS-697
– Max PDCP SN window size						Not present			RBS-698
– PDCP PDU header						Absent			RBS-699
– Header compression information						Not present			RBS-700
– CHOICE RLC info type						RLC info			RBS-701
– CHOICE Uplink RLC mode						UM RLC			RBS-702
– Transmission RLC discard						Not present			RBS-703
– CHOICE Downlink RLC mode						UM RLC			RBS-704
– DL UM RLC LI size						7			RBS-705
– DL Reception Window Size						32			RBS-706
– One sided RLC re-establishment						FALSE			RBS-707
– Alternative E-bit interpretation						Not present			RBS-708
– RB mapping info									RBS-709
– Information for each multiplexing option						1 RBMuxOption			RBS-710
– RLC logical channel mapping indicator						Not Present			RBS-711
– Number of uplink RLC logical channels						1			RBS-712
– Uplink transport channel type						E-DCH			RBS-713
– Logical channel identity						9			RBS-714
– E-DCH MAC-d flow identity						4			RBS-715
– CHOICE RLC PDU size			MAC-I-FIXED			Fixed size		Rel-8	RBS-716
– DDI						7			RBS-717
– RLC PDU size list						12 RLC PDU sizes			RBS-718
– RLC PDU size						96 bits			RBS-719
– RLC PDU size						112 bits			RBS-720
– RLC PDU size						144 bits			RBS-721
– RLC PDU size						160 bits			RBS-722
– RLC PDU size						176 bits			RBS-723
– RLC PDU size						192 bits			RBS-724
– RLC PDU size						208 bits			RBS-725
– RLC PDU size						224 bits			RBS-726
– RLC PDU size						288 bits			RBS-727
– RLC PDU size						296 bits			RBS-728
– RLC PDU size						312 bits			RBS-729
– RLC PDU size						336 bits			RBS-730
– CHOICE RLC PDU size			MAC-I-FLEX			Flexible size		Rel-8	RBS-731
– Length indicator size						Not present			RBS-732
– Minimum UL RLC PDU size						See clause 6.10			RBS-733
– Largest UL RLC PDU size						See clause 6.10			RBS-734
– Include in scheduling info						TRUE			RBS-735
– MAC logical channel priority						8			RBS-736
– Downlink RLC logical channel info									RBS-737
– Number of downlink RLC logical channels						1			RBS-738
– Downlink transport channel type						HS-DSCH			RBS-739
– DL DCH Transport channel identity						Not present			RBS-740
– DL DSCH Transport channel identity						Not present			RBS-741
– DL HS-DSCH MAC-d flow identity						3			RBS-742
– Logical channel identity						Not Present			RBS-743
– RAB information for setup			A17, A17a					Rel-7	RBS-744
			A25a, A28					Rel-8	RBS-745
– RAB info						(high-speed AM DTCH for PS domain)			RBS-746
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-747
– CN domain identity						PS domain			RBS-748
– NAS Synchronization Indicator						Not Present			RBS-749
– Re-establishment timer						useT315			RBS-750
– RB information to setup									RBS-751
– RB identity						25			RBS-752
– PDCP info									RBS-753
– Support for lossless SRNS relocation						FALSE			RBS-754
– Max PDCP SN window size						Not present			RBS-755
– PDCP PDU header						Absent			RBS-756
– Header compression information						Not present			RBS-757
– CHOICE RLC info type						RLC info			RBS-758
– CHOICE Uplink RLC mode						AM RLC			RBS-759
– Transmission RLC discard									RBS-760
– CHOICE SDU discard mode						No Discard			RBS-761
– MAX_DAT						15			RBS-762
– Transmission window size						128			RBS-763
– Timer_RST						500			RBS-764
– Max_RST						4			RBS-765
– Polling info									RBS-766
– Timer_poll_prohibit						100			RBS-767
– Timer_poll						100			RBS-768
– Poll_PDU						Not Present			RBS-769
– Poll_SDU						1			RBS-770
– Last transmission PDU poll						TRUE			RBS-771
– Last retransmission PDU poll						TRUE			RBS-772
– Poll_Windows						99			RBS-773
– Timer_poll_periodic						Not Present			RBS-774
– CHOICE Downlink RLC mode						AM RLC			RBS-775
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set			RBS-776
– Length indicator size						This IE is present and set to “7” if Downlink RLC PDU Size is set to “Flexible”			RBS-777
– In-sequence delivery						TRUE			RBS-778
– Receiving window size						768			RBS-779
– Downlink RLC status info									RBS-780
– Timer_status_prohibit						100			RBS-781
– Timer_EPC						Not Present			RBS-782
– Missing PDU indicator						TRUE			RBS-783
– Timer_STATUS_periodic						Not Present			RBS-784
– One sided RLC re-establishment						FALSE			RBS-785
– Alternative E-bit interpretation						Not present			RBS-786
– Use special value of HE field						TRUE			RBS-787
– RB mapping info									RBS-788
– Information for each multiplexing option						1 RBMuxOption			RBS-789
– RLC logical channel mapping indicator						Not present			RBS-790
– Number of uplink RLC logical channels						1			RBS-791
– Uplink transport channel type						DCH			RBS-792
– UL Transport channel identity						1			RBS-793
– Logical channel identity						Not Present			RBS-794
– CHOICE RLC size list						Configured			RBS-795
– MAC logical channel priority						8			RBS-796
– Downlink RLC logical channel info									RBS-797
– Number of downlink RLC logical channels						1			RBS-798
– Downlink transport channel type						HS-DSCH			RBS-799
– DL DCH Transport channel identity						Not present			RBS-800
– DL DSCH Transport channel identity						Not present			RBS-801
– CHOICE DL MAC header type						MAC-ehs			RBS-802
– DL HS-DSCH MAC-ehs Queue Id						0			RBS-803
– Logical channel identity						7			RBS-804
– RAB information for setup			A17b, A17c,A17d, A17e, A17f,A28a					Rel-7	RBS-805
– RAB info						(high-speed AM DTCH for PS domain)			RBS-806
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-807
– CN domain identity						PS domain			RBS-808
– NAS Synchronization Indicator						Not Present			RBS-809
– Re-establishment timer						useT315			RBS-810
– RB information to setup									RBS-811
– RB identity						25			RBS-812
– PDCP info									RBS-813
– Support for lossless SRNS relocation						FALSE			RBS-814
– Max PDCP SN window size						Not present			RBS-815
– PDCP PDU header						Absent			RBS-816
– Header compression information						Not present			RBS-817
– CHOICE RLC info type						RLC info			RBS-818
– CHOICE Uplink RLC mode						AM RLC			RBS-819
– Transmission RLC discard									RBS-820
– CHOICE SDU discard mode						No Discard			RBS-821
– MAX_DAT						15			RBS-822
– Transmission window size						256			RBS-823
– Timer_RST						500			RBS-824
– Max_RST						4			RBS-825
– Polling info									RBS-826
– Timer_poll_prohibit						100			RBS-827
– Timer_poll						100			RBS-828
– Poll_PDU						Not Present			RBS-829
– Poll_SDU						1			RBS-830
– Last transmission PDU poll						TRUE			RBS-831
– Last retransmission PDU poll						TRUE			RBS-832
– Poll_Windows						99			RBS-833
– Timer_poll_periodic						Not Present			RBS-834
– CHOICE Downlink RLC mode						AM RLC			RBS-835
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set			RBS-836
– Length indicator size						This IE is present and set to “7” if Downlink RLC PDU Size is set to “Flexible”			RBS-837
– In-sequence delivery						TRUE			RBS-838
– Receiving window size						768			RBS-839
– Downlink RLC status info									RBS-840
– Timer_status_prohibit						100			RBS-841
– Timer_EPC						Not Present			RBS-842
– Missing PDU indicator						TRUE			RBS-843
– Timer_STATUS_periodic						Not Present			RBS-844
– One sided RLC re-establishment						FALSE			RBS-845
– Alternative E-bit interpretation						Not present			RBS-846
– Use special value of HE field						TRUE			RBS-847
– RB mapping info									RBS-848
– Information for each multiplexing option						1 RBMuxOption			RBS-849
– RLC logical channel mapping indicator						Not Present			RBS-850
– Number of uplink RLC logical channels						1			RBS-851
– Uplink transport channel type						E-DCH			RBS-852
– Logical channel identity						7			RBS-853
– E-DCH MAC-d flow identity						2			RBS-854
– CHOICE RLC PDU size			MAC-I-FIXED			Fixed size		Rel-8	RBS-855
– DDI						5			RBS-856
– RLC PDU size list						1 RLC PDU size			RBS-857
– RLC PDU size						336 bits			RBS-858
– CHOICE RLC PDU size			MAC-I-FLEX			Flexible size		Rel-8	RBS-859
– Length indicator size						– 15 bit			RBS-860
– Minimum UL RLC PDU size						See clause 6.10			RBS-861
– Largest UL RLC PDU size						See clause 6.10			RBS-862
– Include in scheduling info						TRUE			RBS-863
– MAC logical channel priority						8			RBS-864
– Downlink RLC logical channel info									RBS-865
– Number of downlink RLC logical channels						1			RBS-866
– Downlink transport channel type						HS-DSCH			RBS-867
– DL DCH Transport channel identity						Not present			RBS-868
– DL DSCH Transport channel identity						Not present			RBS-869
– CHOICE DL MAC header type						MAC-ehs			RBS-870
– DL HS-DSCH MAC-ehs Queue Id						0			RBS-871
– Logical channel identity						7			RBS-872
– RAB information for setup			A18					Rel-7	RBS-873
– RAB info						(high-speed UM DTCH for PS domain)			RBS-874
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-875
– CN domain identity						PS domain			RBS-876
– NAS Synchronization Indicator						Not Present			RBS-877
– Re-establishment timer						useT315			RBS-878
– RB information to setup									RBS-879
– RB identity						25			RBS-880
– PDCP info									RBS-881
– Support for lossless SRNS relocation						FALSE			RBS-882
– Max PDCP SN window size						Not present			RBS-883
– PDCP PDU header						Absent			RBS-884
– Header compression information						Not present			RBS-885
– CHOICE RLC info type						RLC info			RBS-886
– CHOICE Uplink RLC mode						UM RLC			RBS-887
– Transmission RLC discard						Not present			RBS-888
– CHOICE Downlink RLC mode						UM RLC			RBS-889
– DL UM RLC LI size						7			RBS-890
– DL Reception Window Size						Not present			RBS-891
– One sided RLC re-establishment						FALSE			RBS-892
– Alternative E-bit interpretation						TRUE			RBS-893
– Use special value of HE field						Not present			RBS-894
– RB mapping info									RBS-895
– Information for each multiplexing option						1 RBMuxOption			RBS-896
– RLC logical channel mapping indicator						Not present			RBS-897
– Number of uplink RLC logical channels						1			RBS-898
– Uplink transport channel type						DCH			RBS-899
– UL Transport channel identity						1			RBS-900
– Logical channel identity						Not Present			RBS-901
– CHOICE RLC size list						Configured			RBS-902
– MAC logical channel priority						8			RBS-903
– Downlink RLC logical channel info									RBS-904
– Number of downlink RLC logical channels						1			RBS-905
– Downlink transport channel type						HS-DSCH			RBS-906
– DL DCH Transport channel identity						Not present			RBS-907
– DL DSCH Transport channel identity						Not present			RBS-908
– CHOICE DL MAC header type						MAC-ehs			RBS-909
– DL HS-DSCH MAC-ehs Queue Id						0			RBS-910
– Logical channel identity						7			RBS-911
– RAB information for setup			,A20, A21					Rel-7	RBS-912
– RAB info						(high-speed AM DTCH for PS domain)			RBS-913
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-914
– CN domain identity						PS domain			RBS-915
– NAS Synchronization Indicator						Not Present			RBS-916
– Re-establishment timer						useT315			RBS-917
– RB information to setup									RBS-918
– RB identity						25			RBS-919
– PDCP info									RBS-920
– Support for lossless SRNS relocation						FALSE			RBS-921
– Max PDCP SN window size						Not present			RBS-922
– PDCP PDU header						Absent			RBS-923
– Header compression information						Not present			RBS-924
– CHOICE RLC info type						RLC info			RBS-925
– CHOICE Uplink RLC mode						AM RLC			RBS-926
– Transmission RLC discard									RBS-927
– CHOICE SDU discard mode						No Discard			RBS-928
– MAX_DAT						15			RBS-929
– Transmission window size						256			RBS-930
– Timer_RST						500			RBS-931
– Max_RST						4			RBS-932
– Polling info									RBS-933
– Timer_poll_prohibit						100			RBS-934
– Timer_poll						100			RBS-935
– Poll_PDU						Not Present			RBS-936
– Poll_SDU						1			RBS-937
– Last transmission PDU poll						TRUE			RBS-938
– Last retransmission PDU poll						TRUE			RBS-939
– Poll_Windows						99			RBS-940
– Timer_poll_periodic						Not Present			RBS-941
– CHOICE Downlink RLC mode						AM RLC			RBS-942
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set			RBS-943
– In-sequence delivery						TRUE			RBS-944
– Receiving window size						768			RBS-945
– Downlink RLC status info									RBS-946
– Timer_status_prohibit						100			RBS-947
– Timer_EPC						Not Present			RBS-948
– Missing PDU indicator						TRUE			RBS-949
– Timer_STATUS_periodic						Not Present			RBS-950
– One sided RLC re-establishment						FALSE			RBS-951
– RB mapping info									RBS-952
– Information for each multiplexing option						1 RBMuxOption			RBS-953
– RLC logical channel mapping indicator						Not Present			RBS-954
– Number of uplink RLC logical channels						1			RBS-955
– Uplink transport channel type						E-DCH			RBS-956
– Logical channel identity						7			RBS-957
– E-DCH MAC-d flow identity						2			RBS-958
– CHOICE RLC PDU size			MAC-I-FIXED			Fixed size		Rel-8	RBS-959
– DDI						5			RBS-960
– RLC PDU size list						1 RLC PDU size			RBS-961
– RLC PDU size						336 bits			RBS-962
– CHOICE RLC PDU size			MAC-I-FLEX			Flexible size		Rel-8	RBS-963
– Length indicator size						– 15 bit			RBS-964
– Minimum UL RLC PDU size						See clause 6.10			RBS-965
– Largest UL RLC PDU size						See clause 6.10			RBS-966
– Include in scheduling info						TRUE			RBS-967
– MAC logical channel priority						8			RBS-968
– Downlink RLC logical channel info									RBS-969
– Number of downlink RLC logical channels						1			RBS-970
– Downlink transport channel type						HS-DSCH			RBS-971
– DL DCH Transport channel identity						Not present			RBS-972
– DL DSCH Transport channel identity						Not present			RBS-973
– CHOICE DL MAC header type						MAC-hs			RBS-974
– DL HS-DSCH MAC-d flow identity						0			RBS-975
– Logical channel identity						Not Present			RBS-976
– RAB information for setup			A21					Rel-7	RBS-977
– RAB info						(Conversational UM DTCH for PS domain)			RBS-978
– RAB identity						0000 0110B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-979
– CN domain identity						PS domain			RBS-980
– NAS Synchronization Indicator						Not Present			RBS-981
– Re-establishment timer						useT314			RBS-982
– RB information to setup									RBS-983
– RB identity						27			RBS-984
– PDCP info									RBS-985
– Support for lossless SRNS relocation						FALSE			RBS-986
– Max PDCP SN window size						Not present			RBS-987
– PDCP PDU header						Absent			RBS-988
– Header compression information						Not present			RBS-989
– CHOICE RLC info type						RLC info			RBS-990
– CHOICE Uplink RLC mode						UM RLC			RBS-991
– Transmission RLC discard						Not present			RBS-992
– CHOICE Downlink RLC mode						UM RLC			RBS-993
– DL UM RLC LI size						7			RBS-994
– DL Reception Window Size						32			RBS-995
– One sided RLC re-establishment						FALSE			RBS-996
– Alternative E-bit interpretation						Not present			RBS-997
– RB mapping info									RBS-998
– Information for each multiplexing option						1 RBMuxOption			RBS-999
– RLC logical channel mapping indicator						Not Present			RBS-1000
– Number of uplink RLC logical channels						1			RBS-1001
– Uplink transport channel type						E-DCH			RBS-1002
– Logical channel identity						9			RBS-1003
– E-DCH MAC-d flow identity						4			RBS-1004
– CHOICE RLC PDU size			MAC-I-FIXED			Fixed size		Rel-8	RBS-1005
– DDI						7			RBS-1006
– RLC PDU size list						12 RLC PDU sizes			RBS-1007
– RLC PDU size						96 bits			RBS-1008
– RLC PDU size						112 bits			RBS-1009
– RLC PDU size						144 bits			RBS-1010
– RLC PDU size						160 bits			RBS-1011
– RLC PDU size						176 bits			RBS-1012
– RLC PDU size						192 bits			RBS-1013
– RLC PDU size						208 bits			RBS-1014
– RLC PDU size						224 bits			RBS-1015
– RLC PDU size						288 bits			RBS-1016
– RLC PDU size						296 bits			RBS-1017
– RLC PDU size						312 bits			RBS-1018
– RLC PDU size						336 bits			RBS-1019
– CHOICE RLC PDU size			MAC-I-FLEX			Flexible size		Rel-8	RBS-1020
– Length indicator size						Not present			RBS-1021
– Minimum UL RLC PDU size						See clause 6.10			RBS-1022
– Largest UL RLC PDU size						See clause 6.10			RBS-1023
– Include in scheduling info						TRUE			RBS-1024
– MAC logical channel priority						8			RBS-1025
– Downlink RLC logical channel info									RBS-1026
– Number of downlink RLC logical channels						1			RBS-1027
– Downlink transport channel type						HS-DSCH			RBS-1028
– DL DCH Transport channel identity						Not present			RBS-1029
– DL DSCH Transport channel identity						Not present			RBS-1030
– CHOICE DL MAC header type						MAC-hs			RBS-1031
– DL HS-DSCH MAC-d flow identity						3			RBS-1032
– Logical channel identity						Not Present			RBS-1033
– RAB information for setup			A22					Rel-7	RBS-1034
– RAB info						(second high-speed UM DTCH for PS domain)			RBS-1035
– RAB identity						0000 0110B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-1036
– CN domain identity						PS domain			RBS-1037
– NAS Synchronization Indicator						Not Present			RBS-1038
– Re-establishment timer						useT315			RBS-1039
– RB information to setup									RBS-1040
– RB identity						27			RBS-1041
– PDCP info									RBS-1042
– Support for lossless SRNS relocation						FALSE			RBS-1043
– Max PDCP SN window size						Not present			RBS-1044
– PDCP PDU header						Absent			RBS-1045
– Header compression information						Not present			RBS-1046
– CHOICE RLC info type						RLC info			RBS-1047
– CHOICE Uplink RLC mode						UM RLC			RBS-1048
– Transmission RLC discard						Not present			RBS-1049
– CHOICE Downlink RLC mode						UM RLC			RBS-1050
– DL UM RLC LI size						15			RBS-1051
– DL Reception Window Size						Not present			RBS-1052
– One sided RLC re-establishment						FALSE			RBS-1053
– Alternative E-bit interpretation						TRUE			RBS-1054
– Use special value of HE field						Not present			RBS-1055
– RB mapping info									RBS-1056
– Information for each multiplexing option						1 RBMuxOption			RBS-1057
– RLC logical channel mapping indicator						Not present			RBS-1058
– Number of uplink RLC logical channels						1			RBS-1059
– Uplink transport channel type						E-DCH			RBS-1060
– Logical channel identity						9			RBS-1061
– E-DCH MAC-d flow identity						4			RBS-1062
– CHOICE RLC PDU size			MAC-I-FIXED			Fixed size		Rel-8	RBS-1063
– DDI						7			RBS-1064
– RLC PDU size list						See clause 6.10			RBS-1065
– CHOICE RLC PDU size			MAC-I-FLEX			Flexible size		Rel-8	RBS-1066
– Length indicator size						15 bit			RBS-1067
– Minimum UL RLC PDU size						See clause 6.10			RBS-1068
– Largest UL RLC PDU size						See clause 6.10			RBS-1069
– Include in scheduling info						TRUE			RBS-1070
– MAC logical channel priority						8			RBS-1071
– Downlink RLC logical channel info									RBS-1072
– Number of downlink RLC logical channels						1			RBS-1073
– Downlink transport channel type						HS-DSCH			RBS-1074
– DL DCH Transport channel identity						Not present			RBS-1075
– DL DSCH Transport channel identity						Not present			RBS-1076
– CHOICE DL MAC header type						MAC-ehs			RBS-1077
– DL HS-DSCH MAC-ehs Queue Id						3			RBS-1078
– Logical channel identity						9			RBS-1079
– RAB information for setup			A22					Rel-7	RBS-1080
			, A25, A25b					Rel-8	RBS-1081
			A25c					Rel-9	RBS-1081a
– RAB info						(high-speed AM DTCH for PS domain)			RBS-1082
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-1083
– CN domain identity						PS domain			RBS-1084
– NAS Synchronization Indicator						Not Present			RBS-1085
– Re-establishment timer						useT315			RBS-1086
– RB information to setup									RBS-1087
– RB identity						25			RBS-1088
– PDCP info									RBS-1089
– Support for lossless SRNS relocation						FALSE			RBS-1090
– Max PDCP SN window size						Not present			RBS-1091
– PDCP PDU header						Absent			RBS-1092
– Header compression information						Not present			RBS-1093
– CHOICE RLC info type						RLC info			RBS-1094
– CHOICE Uplink RLC mode						AM RLC			RBS-1095
– Transmission RLC discard									RBS-1096
– CHOICE SDU discard mode						No Discard			RBS-1097
– MAX_DAT						15			RBS-1098
– Transmission window size						128			RBS-1099
– Timer_RST						500			RBS-1100
– Max_RST						4			RBS-1101
– Polling info									RBS-1102
– Timer_poll_prohibit						100			RBS-1103
– Timer_poll						100			RBS-1104
– Poll_PDU						Not Present			RBS-1105
– Poll_SDU						1			RBS-1106
– Last transmission PDU poll						TRUE			RBS-1107
– Last retransmission PDU poll						TRUE			RBS-1108
– Poll_Windows						99			RBS-1109
– Timer_poll_periodic						Not Present			RBS-1110
– CHOICE Downlink RLC mode						AM RLC			RBS-1111
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set			RBS-1112
– Length indicator size						This IE is present and set to “7” if Downlink RLC PDU Size is set to “Flexible”			RBS-1113
– In-sequence delivery						TRUE			RBS-1114
– Receiving window size						768			RBS-1115
– Downlink RLC status info									RBS-1116
– Timer_status_prohibit						100			RBS-1117
– Timer_EPC						Not Present			RBS-1118
– Missing PDU indicator						TRUE			RBS-1119
– Timer_STATUS_periodic						Not Present			RBS-1120
– One sided RLC re-establishment						FALSE			RBS-1121
– Alternative E-bit interpretation						Not present			RBS-1122
– Use special value of HE field						TRUE			RBS-1123
– RB mapping info									RBS-1124
– Information for each multiplexing option						1 RBMuxOption			RBS-1125
– RLC logical channel mapping indicator						Not present			RBS-1126
– Number of uplink RLC logical channels						1			RBS-1127
– Uplink transport channel type						E-DCH			RBS-1128
– Logical channel identity						7			RBS-1129
– E-DCH MAC-d flow identity						2			RBS-1130
– CHOICE RLC PDU size			MAC-I-FIXED			Fixed size		Rel-8	RBS-1131
– DDI						5			RBS-1132
– RLC PDU size list						1 RLC PDU size			RBS-1133
– RLC PDU size						336 bits			RBS-1134
– CHOICE RLC PDU size			MAC-I-FLEX			Flexible size		Rel-8	RBS-1135
– Length indicator size						15 bit			RBS-1136
– Minimum UL RLC PDU size						See clause 6.10			RBS-1137
– Largest UL RLC PDU size						See clause 6.10			RBS-1138
– Include in scheduling info						TRUE			RBS-1139
– MAC logical channel priority						8			RBS-1140
– Downlink RLC logical channel info									RBS-1141
– Number of downlink RLC logical channels						1			RBS-1142
– Downlink transport channel type						HS-DSCH			RBS-1143
– DL DCH Transport channel identity						Not present			RBS-1144
– DL DSCH Transport channel identity						Not present			RBS-1145
– CHOICE DL MAC header type						MAC-ehs			RBS-1146
– DL HS-DSCH MAC-ehs Queue Id						0			RBS-1147
– Logical channel identity						7			RBS-1148
– RAB information for setup			A23					Rel-7 Rel-8	RBS-1149
– RAB info						(high-speed UM DTCH for CS domain)			RBS-1150
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-1151
– CN domain identity						CS domain			RBS-1152
– NAS Synchronization Indicator						‘1010’ if WB-AMR is tested, otherwise ‘0110’			RBS-1153
– Re-establishment timer						useT314			RBS-1154
– CS-HSPA information									RBS-1155
– UL AMR rate						Not Present			RBS-1156
– Max CS delay						60			RBS-1157
– RB information to setup									RBS-1158
– RB identity						26			RBS-1159
– PDCP info									RBS-1160
– Support for lossless SRNS relocation						FALSE			RBS-1161
– Max PDCP SN window size						Not present			RBS-1162
– PDCP PDU header						present			RBS-1163
– Header compression information						Not present			RBS-1164
– CHOICE RLC info type						RLC info			RBS-1165
– CHOICE Uplink RLC mode						UM RLC			RBS-1166
– Transmission RLC discard									RBS-1167
– CHOICE SDU discard mode						Timer based no explicit			RBS-1168
– Timer_discard						50			RBS-1169
– CHOICE Downlink RLC mode						UM RLC			RBS-1170
– DL UM RLC LI size						7			RBS-1171
– DL Reception Window Size						Not present			RBS-1172
– One sided RLC re-establishment						FALSE			RBS-1173
– Alternative E-bit interpretation						TRUE			RBS-1174
– Use special value of HE field						Not present			RBS-1175
– RB mapping info									RBS-1176
– Information for each multiplexing option						1 RBMuxOption			RBS-1177
– RLC logical channel mapping indicator						Not present			RBS-1178
– Number of uplink RLC logical channels						1			RBS-1179
– Uplink transport channel type						E-DCH			RBS-1180
– Logical channel identity						7			RBS-1181
– E-DCH MAC-d flow identity						2			RBS-1182
– CHOICE RLC PDU size			MAC-I-FIXED			Fixed size		Rel-8	RBS-1183
– DDI						6			RBS-1184
– RLC PDU size list						Reference to clause 6.10 Parameter Set			RBS-1185
– CHOICE RLC PDU size			MAC-I-FLEX			Flexible size		Rel-8	RBS-1186
– Length indicator size						Not present			RBS-1187
– Minimum UL RLC PDU size						See clause 6.10			RBS-1188
– Largest UL RLC PDU size						See clause 6.10			RBS-1189
– Include in scheduling info						TRUE			RBS-1190
– MAC logical channel priority						8			RBS-1191
– Downlink RLC logical channel info									RBS-1192
– Number of downlink RLC logical channels						1			RBS-1193
– Downlink transport channel type						HS-DSCH			RBS-1194
– DL DCH Transport channel identity						Not present			RBS-1195
– DL DSCH Transport channel identity						Not present			RBS-1196
– CHOICE DL MAC header type						MAC-ehs			RBS-1197
– DL HS-DSCH MAC-ehs Queue Id						0			RBS-1198
– Logical channel identity						7			RBS-1199
– RAB information for setup			A24						RBS-1200
– RAB info						(high-speed AM DTCH for PS domain)			RBS-1201
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-1202
– CN domain identity						PS domain			RBS-1203
– NAS Synchronization Indicator						Not Present			RBS-1204
– Re-establishment timer						useT315			RBS-1205
– RB information to setup									RBS-1206
– RB identity						25			RBS-1207
– PDCP info									RBS-1208
– Support for lossless SRNS relocation						FALSE			RBS-1209
– Max PDCP SN window size						Not present			RBS-1210
– PDCP PDU header						Absent			RBS-1211
– Header compression information						Not present			RBS-1212
– CHOICE RLC info type						RLC info			RBS-1213
– CHOICE Uplink RLC mode						AM RLC			RBS-1214
– Transmission RLC discard									RBS-1215
– CHOICE SDU discard mode						No Discard			RBS-1216
– MAX_DAT						15			RBS-1217
– Transmission window size						128			RBS-1218
– Timer_RST						500			RBS-1219
– Max_RST						4			RBS-1220
– Polling info									RBS-1221
– Timer_poll_prohibit						100			RBS-1222
– Timer_poll						100			RBS-1223
– Poll_PDU						Not Present			RBS-1224
– Poll_SDU						1			RBS-1225
– Last transmission PDU poll						TRUE			RBS-1226
– Last retransmission PDU poll						TRUE			RBS-1227
– Poll_Windows						99			RBS-1228
– Timer_poll_periodic						Not Present			RBS-1229
– CHOICE Downlink RLC mode						AM RLC			RBS-1230
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set			RBS-1231
– In-sequence delivery						TRUE			RBS-1232
– Receiving window size						768			RBS-1233
– Downlink RLC status info									RBS-1234
– Timer_status_prohibit						100			RBS-1235
– Timer_EPC						Not Present			RBS-1236
– Missing PDU indicator						TRUE			RBS-1237
– Timer_STATUS_periodic						Not Present			RBS-1238
– One sided RLC re-establishment						FALSE			RBS-1239
– Alternative E-bit interpretation						Not present			RBS-1240
– Use special value of HE field						TRUE			RBS-1241
– RB mapping info									RBS-1242
– Information for each multiplexing option						1 RBMuxOption			RBS-1243
– RLC logical channel mapping indicator						Not present			RBS-1244
– Number of uplink RLC logical channels						1			RBS-1245
– Uplink transport channel type						RACH			RBS-1246
– UL Transport channel identity						Not Present			RBS-1247
– Logical channel identity						7			RBS-1248
– CHOICE RLC size list						Explicit list			RBS-1249
– RLC size index						Reference to clause 6 Parameter Set			RBS-1250
– MAC logical channel priority						8			RBS-1251
– Downlink RLC logical channel info									RBS-1252
– Number of downlink RLC logical channels						1			RBS-1253
– Downlink transport channel type						HS-DSCH			RBS-1254
– DL DCH Transport channel identity						Not present			RBS-1255
– DL DSCH Transport channel identity						Not present			RBS-1256
– CHOICE DL MAC header type						MAC-ehs			RBS-1257
– DL HS-DSCH MAC-ehs Queue Id						2			RBS-1258
– Logical channel identity						Not Present			RBS-1259
– RAB information for setup			A26					Rel-8	RBS-1260
– RAB info						(first UM DTCH for PS domain)			RBS-1261
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-1262
– CN domain identity						PS domain			RBS-1263
– NAS Synchronization Indicator						Not Present			RBS-1264
– Re-establishment timer						useT315			RBS-1265
– RB information to setup									RBS-1266
– RB identity						26			RBS-1267
– PDCP info									RBS-1268
– Support for lossless SRNS relocation						FALSE			RBS-1269
– Max PDCP SN window size						Not present			RBS-1270
– PDCP PDU header						Absent			RBS-1271
– Header compression information						Not present			RBS-1272
– CHOICE RLC info type						RLC info			RBS-1273
– CHOICE Uplink RLC mode						UM RLC			RBS-1274
– Transmission RLC discard						Not present			RBS-1275
– CHOICE Downlink RLC mode						UM RLC			RBS-1276
– DL UM RLC LI size						7			RBS-1277
– DL Reception Window Size						Not present			RBS-1278
– Alternative E-bit interpretation						TRUE			RBS-1279
– One sided RLC re-establishment						FALSE			RBS-1280
– RB mapping info									RBS-1281
– Information for each multiplexing option						1 RBMuxOption			RBS-1282
– RLC logical channel mapping indicator						Not Present			RBS-1283
– Number of uplink RLC logical channels						1			RBS-1284
– Uplink transport channel type						E-DCH			RBS-1285
– Logical channel identity						7			RBS-1286
– E-DCH MAC-d flow identity						2			RBS-1287
– CHOICE RLC PDU size						Flexible size			RBS-1288
– Length indicator size						Not present			RBS-1289
– Minimum UL RLC PDU size						See clause 6.10			RBS-1290
– Largest UL RLC PDU size						See clause 6.10			RBS-1291
– Include in scheduling info						TRUE			RBS-1292
– MAC logical channel priority						8			RBS-1293
– Downlink RLC logical channel info									RBS-1294
– Number of downlink RLC logical channels						1			RBS-1295
– Downlink transport channel type						HS-DSCH			RBS-1296
– DL DCH Transport channel identity						Not present			RBS-1297
– DL DSCH Transport channel identity						Not present			RBS-1298
– CHOICE DL MAC header type						MAC-ehs			RBS-1299
– DL HS-DSCH MAC-ehs Queue Id						2			RBS-1300
– Logical channel identity						7			RBS-1301
– RAB information for setup			A26					Rel-8	RBS-1302
– RAB info						(second high-speed UM DTCH for PS domain)			RBS-1303
– RAB identity						0000 0110B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-1304
– CN domain identity						PS domain			RBS-1305
– NAS Synchronization Indicator						Not Present			RBS-1306
– Re-establishment timer						useT315			RBS-1307
– RB information to setup									RBS-1308
– RB identity						27			RBS-1309
– PDCP info									RBS-1310
– Support for lossless SRNS relocation						FALSE			RBS-1311
– Max PDCP SN window size						Not present			RBS-1312
– PDCP PDU header						Absent			RBS-1313
– Header compression information						Not present			RBS-1314
– CHOICE RLC info type						RLC info			RBS-1315
– CHOICE Uplink RLC mode						UM RLC			RBS-1316
– Transmission RLC discard						Not present			RBS-1317
– CHOICE Downlink RLC mode						UM RLC			RBS-1318
– DL UM RLC LI size						7			RBS-1319
– DL Reception Window Size						Not present			RBS-1320
– Alternative E-bit interpretation						TRUE			RBS-1321
– One sided RLC re-establishment						FALSE			RBS-1322
– RB mapping info									RBS-1323
– Information for each multiplexing option						1 RBMuxOption			RBS-1324
– RLC logical channel mapping indicator						Not Present			RBS-1325
– Number of uplink RLC logical channels						1			RBS-1326
– Uplink transport channel type						E-DCH			RBS-1327
– Logical channel identity						8			RBS-1328
– E-DCH MAC-d flow identity						3			RBS-1329
– CHOICE RLC PDU size						Flexible size			RBS-1330
– Length indicator size						Not present			RBS-1331
– Minimum UL RLC PDU size						See clause 6.10			RBS-1332
– Largest UL RLC PDU size						See clause 6.10			RBS-1333
– Include in scheduling info						TRUE			RBS-1334
– MAC logical channel priority						8			RBS-1335
– Downlink RLC logical channel info									RBS-1336
– Number of downlink RLC logical channels						1			RBS-1337
– Downlink transport channel type						HS-DSCH			RBS-1338
– DL DCH Transport channel identity						Not present			RBS-1339
– DL DSCH Transport channel identity						Not present			RBS-1340
– CHOICE DL MAC header type						MAC-ehs			RBS-1341
– DL HS-DSCH MAC-ehs Queue Id						3			RBS-1342
– Logical channel identity						8			RBS-1343
– RAB information for setup			A26					Rel-8	RBS-1344
– RAB info						(third high-speed UM DTCH for PS domain)			RBS-1345
– RAB identity						0000 0111B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-1346
– CN domain identity						PS domain			RBS-1347
– NAS Synchronization Indicator						Not Present			RBS-1348
– Re-establishment timer						useT315			RBS-1349
– RB information to setup									RBS-1350
– RB identity						21			RBS-1351
– PDCP info									RBS-1352
– Support for lossless SRNS relocation						FALSE			RBS-1353
– Max PDCP SN window size						Not present			RBS-1354
– PDCP PDU header						Absent			RBS-1355
– Header compression information						Not present			RBS-1356
– CHOICE RLC info type						RLC info			RBS-1357
– CHOICE Uplink RLC mode						UM RLC			RBS-1358
– Transmission RLC discard						Not present			RBS-1359
– CHOICE Downlink RLC mode						UM RLC			RBS-1360
– DL UM RLC LI size						7			RBS-1361
– DL Reception Window Size						Not present			RBS-1362
– Alternative E-bit interpretation						TRUE			RBS-1363
– One sided RLC re-establishment						FALSE			RBS-1364
– RB mapping info									RBS-1365
– Information for each multiplexing option						1 RBMuxOption			RBS-1366
– RLC logical channel mapping indicator						Not Present			RBS-1367
– Number of uplink RLC logical channels						1			RBS-1368
– Uplink transport channel type						E-DCH			RBS-1369
– Logical channel identity						9			RBS-1370
– E-DCH MAC-d flow identity						4			RBS-1371
– CHOICE RLC PDU size						Flexible size			RBS-1372
– Length indicator size						Not present			RBS-1373
– Minimum UL RLC PDU size						See clause 6.10			RBS-1374
– Largest UL RLC PDU size						See clause 6.10			RBS-1375
– Include in scheduling info						TRUE			RBS-1376
– MAC logical channel priority						8			RBS-1377
– Downlink RLC logical channel info									RBS-1378
– Number of downlink RLC logical channels						1			RBS-1379
– Downlink transport channel type						HS-DSCH			RBS-1380
– DL DCH Transport channel identity						Not present			RBS-1381
– DL DSCH Transport channel identity						Not present			RBS-1382
– CHOICE DL MAC header type						MAC-ehs			RBS-1383
– DL HS-DSCH MAC-ehs Queue Id						4			RBS-1384
– Logical channel identity						9			RBS-1385
– RAB information for setup			A27, A27a					Rel-8	RBS-1386
– RAB info						(high-speed UM DTCH for PS domain)			RBS-1387
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-1388
– CN domain identity						PS domain			RBS-1389
– NAS Synchronization Indicator						Not Present			RBS-1390
– Re-establishment timer						useT315			RBS-1391
– RB information to setup									RBS-1392
– RB identity						25			RBS-1393
– PDCP info									RBS-1394
– Support for lossless SRNS relocation						FALSE			RBS-1395
– Max PDCP SN window size						Not present			RBS-1396
– PDCP PDU header						Absent			RBS-1397
– Header compression information						Not present			RBS-1398
– CHOICE RLC info type						RLC info			RBS-1399
– CHOICE Uplink RLC mode						UM RLC			RBS-1400
– Transmission RLC discard						Not Present			RBS-1401
– CHOICE Downlink RLC mode						UM RLC			RBS-1402
– DL UM RLC LI size						15			RBS-1403
– DL Reception Window Size						Not present			RBS-1404
– One sided RLC re-establishment						FALSE			RBS-1405
– Alternative E-bit interpretation						TRUE			RBS-1406
– Use special value of HE field						Not present			RBS-1407
– RB mapping info									RBS-1408
– Information for each multiplexing option						1 RBMuxOption			RBS-1409
– RLC logical channel mapping indicator						Not present			RBS-1410
– Number of uplink RLC logical channels						1			RBS-1411
– Uplink transport channel type						E-DCH			RBS-1412
– Logical channel identity						7			RBS-1413
– E-DCH MAC-d flow identity						2			RBS-1414
– CHOICE RLC PDU size						Flexible size			RBS-1415
– Length indicator size						Not present			RBS-1416
– Minimum UL RLC PDU size						See clause 6.10			RBS-1417
– Largest UL RLC PDU size						See clause 6.10			RBS-1418
– Include in scheduling info						TRUE			RBS-1419
– MAC logical channel priority						8			RBS-1420
– Downlink RLC logical channel info									RBS-1421
– Number of downlink RLC logical channels						1			RBS-1422
– Downlink transport channel type						HS-DSCH			RBS-1423
– DL DCH Transport channel identity						Not present			RBS-1424
– DL DSCH Transport channel identity						Not present			RBS-1425
– CHOICE DL MAC header type						MAC-ehs			RBS-1426
– DL HS-DSCH MAC-ehs Queue Id						0			RBS-1427
– Logical channel identity						7			RBS-1428
– RAB information for setup			A29					Rel-8	RBS-1429
– RAB info						(high-speed AM DTCH for PS domain)			RBS-1430
– RAB identity						0000 0101B			RBS-1431
The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.									RBS-1432
– CN domain identity						PS domain			RBS-1433
– NAS Synchronization Indicator						Not Present			RBS-1434
– Re-establishment timer						useT315			RBS-1435
– RB information to setup									RBS-1436
– RB identity						25			RBS-1437
– PDCP info									RBS-1438
– Support for lossless SRNS relocation						FALSE			RBS-1439
– Max PDCP SN window size						Not present			RBS-1440
– PDCP PDU header						Absent			RBS-1441
– Header compression information						Not present			RBS-1442
– CHOICE RLC info type						RLC info			RBS-1443
– CHOICE Uplink RLC mode						AM RLC			RBS-1444
– Transmission RLC discard									RBS-1445
– CHOICE SDU discard mode						No Discard			RBS-1446
– MAX_DAT						15			RBS-1447
– Transmission window size						128			RBS-1448
– Timer_RST						500			RBS-1449
– Max_RST						4			RBS-1450
– Polling info									RBS-1451
– Timer_poll_prohibit						100			RBS-1452
– Timer_poll						100			RBS-1453
– Poll_PDU						Not Present			RBS-1454
– Poll_SDU						1			RBS-1455
– Last transmission PDU poll						TRUE			RBS-1456
– Last retransmission PDU poll						TRUE			RBS-1457
– Poll_Windows						99			RBS-1458
– Timer_poll_periodic						Not Present			RBS-1459
– CHOICE Downlink RLC mode						AM RLC			RBS-1460
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set			RBS-1461
– In-sequence delivery						TRUE			RBS-1462
– Receiving window size						768			RBS-1463
– Downlink RLC status info									RBS-1464
– Timer_status_prohibit						100			RBS-1465
– Timer_EPC						Not Present			RBS-1466
– Missing PDU indicator						TRUE			RBS-1467
– Timer_STATUS_periodic						Not Present			RBS-1468
– One sided RLC re-establishment						FALSE			RBS-1469
– Alternative E-bit interpretation						Not present			RBS-1470
– Use special value of HE field						TRUE			RBS-1471
– RB mapping info									RBS-1472
– Information for each multiplexing option						1 RBMuxOption			RBS-1473
– RLC logical channel mapping indicator						Not present			RBS-1474
– Number of uplink RLC logical channels						1			RBS-1475
– Uplink transport channel type						E-DCH			RBS-1476
– Logical channel identity						7			RBS-1477
– E-DCH MAC-d flow identity						0			RBS-1478
– CHOICE RLC PDU size						Flexible size			RBS-1479
– Length indicator size						15 bit			RBS-1480
– Minimum UL RLC PDU size						See clause 6.10			RBS-1481
– Largest UL RLC PDU size						See clause 6.10			RBS-1482
– Include in scheduling info						TRUE			RBS-1483
– MAC logical channel priority						8			RBS-1484
– Downlink RLC logical channel info									RBS-1485
– Number of downlink RLC logical channels						1			RBS-1486
– Downlink transport channel type						HS-DSCH			RBS-1487
– DL DCH Transport channel identity						Not present			RBS-1488
– DL DSCH Transport channel identity						Not present			RBS-1489
– CHOICE DL MAC header type						MAC-ehs			RBS-1490
– DL HS-DSCH MAC-ehs Queue Id						2			RBS-1491
– Logical channel identity						7			RBS-1492
– RAB information for setup			A30					Rel-8	RBS-1493
– RAB info						(high-speed AM DTCH for PS domain)			RBS-1494
– RAB identity						0000 0101B			RBS-1495
The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.									RBS-1496
– CN domain identity						PS domain			RBS-1497
– NAS Synchronization Indicator						Not Present			RBS-1498
– Re-establishment timer						useT315			RBS-1499
– RB information to setup									RBS-1500
– RB identity						25			RBS-1501
– PDCP info									RBS-1502
– Support for lossless SRNS relocation						FALSE			RBS-1503
– Max PDCP SN window size						Not present			RBS-1504
– PDCP PDU header						Absent			RBS-1505
– Header compression information						Not present			RBS-1506
– CHOICE RLC info type						RLC info			RBS-1507
– CHOICE Uplink RLC mode						AM RLC			RBS-1508
– Transmission RLC discard									RBS-1509
– CHOICE SDU discard mode						No Discard			RBS-1510
– MAX_DAT						15			RBS-1511
– Transmission window size						128			RBS-1512
– Timer_RST						500			RBS-1513
– Max_RST						4			RBS-1514
– Polling info									RBS-1515
– Timer_poll_prohibit						100			RBS-1516
– Timer_poll						100			RBS-1517
– Poll_PDU						Not Present			RBS-1518
– Poll_SDU						1			RBS-1519
– Last transmission PDU poll						TRUE			RBS-1520
– Last retransmission PDU poll						TRUE			RBS-1521
– Poll_Windows						99			RBS-1522
– Timer_poll_periodic						Not Present			RBS-1523
– CHOICE Downlink RLC mode						AM RLC			RBS-1524
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set			RBS-1525
– In-sequence delivery						TRUE			RBS-1526
– Receiving window size						768			RBS-1527
– Downlink RLC status info									RBS-1528
– Timer_status_prohibit						100			RBS-1529
– Timer_EPC						Not Present			RBS-1530
– Missing PDU indicator						TRUE			RBS-1531
– Timer_STATUS_periodic						Not Present			RBS-1532
– One sided RLC re-establishment						FALSE			RBS-1533
– Alternative E-bit interpretation						Not present			RBS-1534
– Use special value of HE field						TRUE			RBS-1535
– RB mapping info									RBS-1536
– Information for each multiplexing option						1 RBMuxOption			RBS-1537
– RLC logical channel mapping indicator						Not present			RBS-1538
– Number of uplink RLC logical channels						1			RBS-1539
– Uplink transport channel type						E-DCH			RBS-1540
– Logical channel identity						7			RBS-1541
– E-DCH MAC-d flow identity						2			RBS-1542
– CHOICE RLC PDU size						Flexible size			RBS-1543
– Length indicator size						15 bit			RBS-1544
– Minimum UL RLC PDU size						See clause 6.10			RBS-1545
– Largest UL RLC PDU size						See clause 6.10			RBS-1546
– Include in scheduling info						TRUE			RBS-1547
– MAC logical channel priority						8			RBS-1548
– Downlink RLC logical channel info									RBS-1549
– Number of downlink RLC logical channels						1			RBS-1550
– Downlink transport channel type						HS-DSCH			RBS-1551
– DL DCH Transport channel identity						Not present			RBS-1552
– DL DSCH Transport channel identity						Not present			RBS-1553
– CHOICE DL MAC header type						MAC-ehs			RBS-1554
– DL HS-DSCH MAC-ehs Queue Id						2			RBS-1555
– Logical channel identity						7			RBS-1556
– RAB information for setup			A31, A32					Rel-9	RBS-1557
– RAB info						(high-speed AM DTCH for PS domain)			RBS-1558
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-1559
– CN domain identity						PS domain			RBS-1560
– NAS Synchronization Indicator						Not Present			RBS-1561
– Re-establishment timer						useT315			RBS-1562
– RB information to setup									RBS-1563
– RB identity						25			RBS-1564
– PDCP info									RBS-1565
– Support for lossless SRNS relocation						FALSE			RBS-1566
– Max PDCP SN window size						Not present			RBS-1567
– PDCP PDU header						Absent			RBS-1568
– Header compression information						Not present			RBS-1569
– CHOICE RLC info type						RLC info			RBS-1570
– CHOICE Uplink RLC mode						AM RLC			RBS-1571
– Transmission RLC discard									RBS-1572
– CHOICE SDU discard mode						No Discard			RBS-1573
– MAX_DAT						15			RBS-1574
– Transmission window size						2047			RBS-1575
– Timer_RST						500			RBS-1576
– Max_RST						4			RBS-1577
– Polling info									RBS-1578
– Timer_poll_prohibit						100			RBS-1579
– Timer_poll						100			RBS-1580
– Poll_PDU						Not Present			RBS-1581
– Poll_SDU						1			RBS-1582
– Last transmission PDU poll						TRUE			RBS-1583
– Last retransmission PDU poll						TRUE			RBS-1584
– Poll_Windows						50			RBS-1585
– Timer_poll_periodic						Not Present			RBS-1586
– CHOICE Downlink RLC mode						AM RLC			RBS-1587
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set			RBS-1588
– Length indicator size						This IE is present and set to “7” if Downlink RLC PDU Size is set to “Flexible”			RBS-1589
– In-sequence delivery						TRUE			RBS-1590
– Receiving window size						2047			RBS-1591
– Downlink RLC status info									RBS-1592
– Timer_status_prohibit						80			RBS-1593
– Timer_EPC						Not Present			RBS-1594
– Missing PDU indicator						TRUE			RBS-1595
– Timer_STATUS_periodic						Not Present			RBS-1596
– One sided RLC re-establishment						FALSE			RBS-1597
– Alternative E-bit interpretation						Not present			RBS-1598
– Use special value of HE field						TRUE			RBS-1599
– RB mapping info									RBS-1600
– Information for each multiplexing option						1 RBMuxOption			RBS-1601
– RLC logical channel mapping indicator						Not present			RBS-1602
– Number of uplink RLC logical channels						1			RBS-1603
– Uplink transport channel type						E-DCH			RBS-1604
– Logical channel identity						7			RBS-1605
– E-DCH MAC-d flow identity						2			RBS-1606
– CHOICE RLC PDU size						Fixed size			RBS-1607
– DDI						7			RBS-1608
– RLC PDU size list						See clause 6.10			RBS-1609
– Include in scheduling info						TRUE			RBS-1611
– MAC logical channel priority						8			RBS-1612
– Downlink RLC logical channel info									RBS-1613
– Number of downlink RLC logical channels						1			RBS-1614
– Downlink transport channel type						HS-DSCH			RBS-1615
– DL DCH Transport channel identity						Not present			RBS-1616
– DL DSCH Transport channel identity						Not present			RBS-1617
– CHOICE DL MAC header type						MAC-ehs			RBS-1618
– DL HS-DSCH MAC-ehs Queue Id						0			RBS-1619
– Logical channel identity						7			RBS-1620
– RAB information for setup					A31, A32			Rel-9	RBS-1621
– RAB info						(high-speed AM DTCH for PS domain)			RBS-1622
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-1623
– CN domain identity						PS domain			RBS-1624
– NAS Synchronization Indicator						Not Present			RBS-1625
– Re-establishment timer						useT315			RBS-1626
– RB information to setup									RBS-1627
– RB identity						25			RBS-1628
– PDCP info									RBS-1629
– Support for lossless SRNS relocation						FALSE			RBS-1630
– Max PDCP SN window size						Not present			RBS-1631
– PDCP PDU header						Absent			RBS-1632
– Header compression information						Not present			RBS-1633
– CHOICE RLC info type						RLC info			RBS-1634
– CHOICE Uplink RLC mode						AM RLC			RBS-1635
– Transmission RLC discard									RBS-1636
– CHOICE SDU discard mode						No Discard			RBS-1637
– MAX_DAT						15			RBS-1638
– Transmission window size						2047			RBS-1639
– Timer_RST						500			RBS-1640
– Max_RST						4			RBS-1641
– Polling info									RBS-1642
– Timer_poll_prohibit						100			RBS-1643
– Timer_poll						100			RBS-1644
– Poll_PDU						Not Present			RBS-1645
– Poll_SDU						1			RBS-1646
– Last transmission PDU poll						TRUE			RBS-1647
– Last retransmission PDU poll						TRUE			RBS-1648
– Poll_Windows						50			RBS-1649
– Timer_poll_periodic						Not Present			RBS-1650
– CHOICE Downlink RLC mode						AM RLC			RBS-1651
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set			RBS-1652
– Length indicator size						This IE is present and set to “7” if Downlink RLC PDU Size is set to “Flexible”			RBS-1653
– In-sequence delivery						TRUE			RBS-1654
– Receiving window size						2047			RBS-1655
– Downlink RLC status info									RBS-1656
– Timer_status_prohibit						80			RBS-1657
– Timer_EPC						Not Present			RBS-1658
– Missing PDU indicator						TRUE			RBS-1659
– Timer_STATUS_periodic						Not Present			RBS-1660
– One sided RLC re-establishment						FALSE			RBS-1661
– Alternative E-bit interpretation						Not present			RBS-1662
– Use special value of HE field						TRUE			RBS-1663
– RB mapping info									RBS-1664
– Information for each multiplexing option						1 RBMuxOption			RBS-1665
– RLC logical channel mapping indicator						Not present			RBS-1666
– Number of uplink RLC logical channels						1			RBS-1667
– Uplink transport channel type						E-DCH			RBS-1668
– Logical channel identity						7			RBS-1669
– E-DCH MAC-d flow identity						2			RBS-1670
– CHOICE RLC PDU size						Fixed size			RBS-1671
– DDI						7			RBS-1672
– RLC PDU size list						See clause 6.10			RBS-1673
– Include in scheduling info						TRUE			RBS-1674
– MAC logical channel priority						8			RBS-1675
– Downlink RLC logical channel info									RBS-1676
– Number of downlink RLC logical channels						1			RBS-1677
– Downlink transport channel type						HS-DSCH			RBS-1678
– DL DCH Transport channel identity						Not present			RBS-1679
– DL DSCH Transport channel identity						Not present			RBS-1680
– CHOICE DL MAC header type						MAC-ehs			RBS-1681
– DL HS-DSCH MAC-ehs Queue Id						0			RBS-1682
– Logical channel identity						7			RBS-1683
– RAB information for setup		A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43					Rel-10 Rel-11		RBS-1684
– RAB info						(high-speed AM DTCH for PS domain)			RBS-1685
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-1686
– CN domain identity						PS domain			RBS-1687
– NAS Synchronization Indicator						Not Present			RBS-1688
– Re-establishment timer						useT315			RBS-1689
– RB information to setup									RBS-1690
– RB identity						25			RBS-1691
– PDCP info									RBS-1692
– Support for lossless SRNS relocation						FALSE			RBS-1693
– Max PDCP SN window size						Not present			RBS-1694
– PDCP PDU header						Absent			RBS-1695
– Header compression information						Not present			RBS-1696
– CHOICE RLC info type						RLC info			RBS-1697
– CHOICE Uplink RLC mode						AM RLC			RBS-1698
– Transmission RLC discard									RBS-1699
– CHOICE SDU discard mode						No Discard			RBS-1700
– MAX_DAT						15			RBS-1701
– Transmission window size						2047			RBS-1702
– Timer_RST						500			RBS-1703
– Max_RST						4			RBS-1704
– Polling info									RBS-1705
– Timer_poll_prohibit						100			RBS-1706
– Timer_poll						100			RBS-1707
– Poll_PDU						Not Present			RBS-1708
– Poll_SDU						1			RBS-1709
– Last transmission PDU poll						TRUE			RBS-1710
– Last retransmission PDU poll						TRUE			RBS-1711
– Poll_Windows						50			RBS-1712
– Timer_poll_periodic						Not Present			RBS-1713
– CHOICE Downlink RLC mode						AM RLC			RBS-1714
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set			RBS-1715
– Length indicator size						This IE is present and set to “7” if Downlink RLC PDU Size is set to “Flexible”			RBS-1716
– In-sequence delivery						TRUE			RBS-1717
– Receiving window size						2047			RBS-1718
– Downlink RLC status info									RBS-1719
– Timer_status_prohibit						80			RBS-1720
– Timer_EPC						Not Present			RBS-1721
– Missing PDU indicator						TRUE			RBS-1722
– Timer_STATUS_periodic						Not Present			RBS-1723
– One sided RLC re-establishment						FALSE			RBS-1724
– Alternative E-bit interpretation						Not present			RBS-1725
– Use special value of HE field						TRUE			RBS-1726
– RB mapping info									RBS-1727
– Information for each multiplexing option						1 RBMuxOption			RBS-1728
– RLC logical channel mapping indicator						Not present			RBS-1729
– Number of uplink RLC logical channels						1			RBS-1730
– Uplink transport channel type						E-DCH			RBS-1731
– Logical channel identity						7			RBS-1732
– E-DCH MAC-d flow identity						2			RBS-1733
– CHOICE RLC PDU size						Flexible size			RBS-1734
– Length indicator size						15 bit			RBS-1735
– Minimum UL RLC PDU size						16			RBS-1736
– Largest UL RLC PDU size						2432			RBS-1737
– Include in scheduling info						TRUE			RBS-1738
– MAC logical channel priority						8			RBS-1739
– Downlink RLC logical channel info									RBS-1740
– Number of downlink RLC logical channels						1			RBS-1741
– Downlink transport channel type						HS-DSCH			RBS-1742
– DL DCH Transport channel identity						Not present			RBS-1743
– DL DSCH Transport channel identity						Not present			RBS-1744
– CHOICE DL MAC header type						MAC-ehs			RBS-1745
– DL HS-DSCH MAC-ehs Queue Id						0			RBS-1746
– Logical channel identity						7			RBS-1747
– RAB information for setup		A44, A45					Rel-11		RBS-1748
– RAB info						(high-speed AM DTCH for PS domain)			RBS-1749
– RAB identity						0000 0101B The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.			RBS-1750
– CN domain identity						PS domain			RBS-1751
– NAS Synchronization Indicator						Not Present			RBS-1752
– Re-establishment timer						useT315			RBS-1753
– RB information to setup									RBS-1754
– RB identity						25			RBS-1755
– PDCP info									RBS-1756
– Support for lossless SRNS relocation						FALSE			RBS-1757
– Max PDCP SN window size						Not present			RBS-1758
– PDCP PDU header						Absent			RBS-1759
– Header compression information						Not present			RBS-1760
– CHOICE RLC info type						RLC info			RBS-1761
– CHOICE Uplink RLC mode						AM RLC			RBS-1762
– Transmission RLC discard									RBS-1763
– CHOICE SDU discard mode						No Discard			RBS-1764
– MAX_DAT						15			RBS-1765
– Transmission window size						2047			RBS-1766
– Timer_RST						500			RBS-1767
– Max_RST						4			RBS-1768
– Polling info									RBS-1769
– Timer_poll_prohibit						100			RBS-1770
– Timer_poll						100			RBS-1771
– Poll_PDU						Not Present			RBS-1772
– Poll_SDU						1			RBS-1773
– Last transmission PDU poll						TRUE			RBS-1774
– Last retransmission PDU poll						TRUE			RBS-1775
– Poll_Windows						50			RBS-1776
– Timer_poll_periodic						Not Present			RBS-1777
– CHOICE Downlink RLC mode						AM RLC			RBS-1778
– CHOICE Downlink RLC PDU Size						Reference to clause 6 Parameter Set			RBS-1779
– Length indicator size						This IE is present and set to “7” if Downlink RLC PDU Size is set to “Flexible”			RBS-1780
– In-sequence delivery						TRUE			RBS-1781
– Receiving window size						2047			RBS-1782
– Downlink RLC status info									RBS-1783
– Timer_status_prohibit						80			RBS-1784
– Timer_EPC						Not Present			RBS-1785
– Missing PDU indicator						TRUE			RBS-1786
– Timer_STATUS_periodic – Timer_Reordering						Not Present 200			RBS-1787
– One sided RLC re-establishment						FALSE			RBS-1788
– Alternative E-bit interpretation						Not present			RBS-1789
– Use special value of HE field						TRUE			RBS-1790
– RB mapping info									RBS-1791
– Information for each multiplexing option						1 RBMuxOption			RBS-1792
– RLC logical channel mapping indicator						Not present			RBS-1793
– Number of uplink RLC logical channels						1			RBS-1794
– Uplink transport channel type						E-DCH			RBS-1795
– Logical channel identity						7			RBS-1796
– E-DCH MAC-d flow identity						2			RBS-1797
– CHOICE RLC PDU size						Flexible size			RBS-1798
– Length indicator size						15 bit			RBS-1799
– Minimum UL RLC PDU size						16			RBS-1800
– Largest UL RLC PDU size						2432			RBS-1801
– Include in scheduling info						TRUE			RBS-1802
– MAC logical channel priority						8			RBS-1803
– Downlink RLC logical channel info									RBS-1804
– Number of downlink RLC logical channels						1			RBS-1805
– Downlink transport channel type						HS-DSCH			RBS-1806
– DL DCH Transport channel identity						Not present			RBS-1807
– DL DSCH Transport channel identity						Not present			RBS-1808
– CHOICE DL MAC header type						MAC-ehs			RBS-1809
– DL HS-DSCH MAC-ehs Queue Id						0			RBS-1810
– Logical channel identity						7			RBS-1811
RB information to reconfigure list			A1, A2, A3, A4, A5, A6, A7, A8			Not Present			RBS-1812
			A9, A10					Rel-5	RBS-1813
			A12, A13, A14, A15, A16					Rel-6	RBS-1814
			, A17, A17a, A17f, A18, A19, A19a, A20, A21, A22					Rel-7	RBS-1815
			, A23, A28a					Rel-7 Rel-8	RBS-1816
			, A25, A25a, A25b, A26, A27, A27a, A28, A29					Rel-8	RBS-1817
			,A25c, A31, A32 A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-1818
RB information to be affected			A1, A2, A3, A4, A5, A6, A7, A8, A11			Not Present			RBS-1819
			, A9, A10					Rel-5	RBS-1820
			A12					Rel-6	RBS-1821
			, A17, A17a, A17f, A18, A19, A20, A21, A24					Rel-7	RBS-1822
			, A23					Rel-7 Rel-8	RBS-1823
			, A25a, A28, A29 A35 A38, A39, A40, A41, A42, A43, A44, A45					Rel-8 Rel-10 Rel-11	RBS-1824
RB information to be affected			A13, A15 A19a, A25b					Rel-6	RBS-1825
			, A17d, A17e					Rel-7	RBS-1826
			, A26					Rel-8	RBS-1827
								Rel-9	RBS-1828
– RB identity						1 (UM DCCH for RRC)			RBS-1829
– RB mapping info									RBS-1830
– Information for each multiplexing option						1 RBMuxOption			RBS-1831
– RLC logical channel mapping indicator						Not Present			RBS-1832
– Number of uplink RLC logical channels						1			RBS-1833
– Uplink transport channel type						E-DCH			RBS-1834
– Logical channel identity						1			RBS-1835
– E-DCH MAC-d flow identity						1			RBS-1836
– CHOICE RLC PDU size						Fixed size		Rel-8	RBS-1837
– DDI						1			RBS-1838
– RLC PDU size list						1 RLC PDU size			RBS-1839
– RLC PDU size						144 bits			RBS-1840
– Include in scheduling info						FALSE			RBS-1841
– MAC logical channel priority						1			RBS-1842
– Downlink RLC logical channel info									RBS-1843
– Number of RLC logical channels						1			RBS-1844
– Downlink transport channel type						DCH			RBS-1845
– DL DCH Transport channel identity						10			RBS-1846
– DL DSCH Transport channel identity						Not Present			RBS-1847
– Logical channel identity						1			RBS-1848
– RB identity						2 (AM DCCH for RRC)			RBS-1849
– RB mapping info									RBS-1850
– Information for each multiplexing option						1 RBMuxOption			RBS-1851
– RLC logical channel mapping indicator						Not Present			RBS-1852
– Number of uplink RLC logical channels						1			RBS-1853
– Uplink transport channel type						E-DCH			RBS-1854
– Logical channel identity						2			RBS-1855
– E-DCH MAC-d flow identity						1			RBS-1856
– CHOICE RLC PDU size						Fixed size		Rel-8	RBS-1857
– DDI						2			RBS-1858
– RLC PDU size list						1 RLC PDU size			RBS-1859
– RLC PDU size						144 bits			RBS-1860
– Include in scheduling info						FALSE			RBS-1861
– MAC logical channel priority						2			RBS-1862
– Downlink RLC logical channel info									RBS-1863
– Number of RLC logical channels						1			RBS-1864
– Downlink transport channel type						DCH			RBS-1865
– DL DCH Transport channel identity						10			RBS-1866
– DL DSCH Transport channel identity						Not Present			RBS-1867
– Logical channel identity						2			RBS-1868
– RB identity						3 (AM DCCH for NAS High Priority)			RBS-1869
– RB mapping info									RBS-1870
– Information for each multiplexing option						1 RBMuxOption			RBS-1871
– RLC logical channel mapping indicator						Not Present			RBS-1872
– Number of uplink RLC logical channels						1			RBS-1873
– Uplink transport channel type						E-DCH			RBS-1874
– Logical channel identity						3			RBS-1875
– E-DCH MAC-d flow identity						1			RBS-1876
– CHOICE RLC PDU size						Fixed size		Rel-8	RBS-1877
– DDI						3			RBS-1878
– RLC PDU size list						1 RLC PDU size			RBS-1879
– RLC PDU size						144 bits			RBS-1880
– Include in scheduling info						FALSE			RBS-1881
– MAC logical channel priority						3			RBS-1882
– Downlink RLC logical channel info									RBS-1883
– Number of RLC logical channels						1			RBS-1884
– Downlink transport channel type						DCH			RBS-1885
– DL DCH Transport channel identity						10			RBS-1886
– DL DSCH Transport channel identity						Not Present			RBS-1887
– Logical channel identity						3			RBS-1888
– RB identity						4 (AM DCCH for NAS Low Priority)			RBS-1889
– RB mapping info									RBS-1890
– Information for each multiplexing option						1 RBMuxOption			RBS-1891
– RLC logical channel mapping indicator						Not Present			RBS-1892
– Number of uplink RLC logical channels						1			RBS-1893
– Uplink transport channel type						E-DCH			RBS-1894
– Logical channel identity						4			RBS-1895
– E-DCH MAC-d flow identity						1			RBS-1896
– CHOICE RLC PDU size						Fixed size		Rel-8	RBS-1897
– DDI						4			RBS-1898
– RLC PDU size list						1 RLC PDU size			RBS-1899
– RLC PDU size						144 bits			RBS-1900
– Include in scheduling info						FALSE			RBS-1901
– MAC logical channel priority						4			RBS-1902
– Downlink RLC logical channel info									RBS-1903
– Number of RLC logical channels						1			RBS-1904
– Downlink transport channel type						DCH			RBS-1905
– DL DCH Transport channel identity						10			RBS-1906
– DL DSCH Transport channel identity						Not Present			RBS-1907
– Logical channel identity						4			RBS-1908
RB information to be affected			A14, A16 , A19b					Rel-6 Rel-7	RBS-1909
			, A31, A32					Rel-9	RBS-1910
– RB identity						1 (UM DCCH for RRC)			RBS-1911
– RB mapping info									RBS-1912
– Information for each multiplexing option						1 RBMuxOption			RBS-1913
– RLC logical channel mapping indicator						Not Present			RBS-1914
– Number of uplink RLC logical channels						1			RBS-1915
– Uplink transport channel type						E-DCH			RBS-1916
– Logical channel identity						1			RBS-1917
– E-DCH MAC-d flow identity						1			RBS-1918
– CHOICE RLC PDU size						Fixed size		Rel-8	RBS-1919
– DDI						1			RBS-1920
– RLC PDU size list						1 RLC PDU size			RBS-1921
– RLC PDU size						144 bits			RBS-1922
– Include in scheduling info						FALSE			RBS-1923
– MAC logical channel priority						1			RBS-1924
– Downlink RLC logical channel info									RBS-1925
– Number of RLC logical channels						1			RBS-1926
– Downlink transport channel type						HS-DSCH			RBS-1927
– DL DCH Transport channel identity						Not present			RBS-1928
– DL DSCH Transport channel identity						Not present			RBS-1929
– DL HS-DSCH MAC-d flow identity						1			RBS-1930
– Logical channel identity						1			RBS-1931
– RB identity						2 (AM DCCH for RRC)			RBS-1932
– RB mapping info									RBS-1933
– Information for each multiplexing option						1 RBMuxOption			RBS-1934
– RLC logical channel mapping indicator						Not Present			RBS-1935
– Number of uplink RLC logical channels						1			RBS-1936
– Uplink transport channel type						E-DCH			RBS-1937
– Logical channel identity						2			RBS-1938
– E-DCH MAC-d flow identity						1			RBS-1939
– CHOICE RLC PDU size						Fixed size		Rel-8	RBS-1940
– DDI						2			RBS-1941
– RLC PDU size list						1 RLC PDU size			RBS-1942
– RLC PDU size						144 bits			RBS-1943
– Include in scheduling info						FALSE			RBS-1944
– MAC logical channel priority						2			RBS-1945
– Downlink RLC logical channel info									RBS-1946
– Number of RLC logical channels						1			RBS-1947
– Downlink transport channel type						HS-DSCH			RBS-1948
– DL DCH Transport channel identity						Not Present			RBS-1949
– DL DSCH Transport channel identity						Not Present			RBS-1950
– DL HS-DSCH MAC-d flow identity						1			RBS-1951
– Logical channel identity						2			RBS-1952
– RB identity						3 (AM DCCH for NAS High Priority)			RBS-1953
– RB mapping info									RBS-1954
– Information for each multiplexing option						1 RBMuxOption			RBS-1955
– RLC logical channel mapping indicator						Not Present			RBS-1956
– Number of uplink RLC logical channels						1			RBS-1957
– Uplink transport channel type						E-DCH			RBS-1958
– Logical channel identity						3			RBS-1959
– E-DCH MAC-d flow identity						1			RBS-1960
– CHOICE RLC PDU size						Fixed size		Rel-8	RBS-1961
– DDI						3			RBS-1962
– RLC PDU size list						1 RLC PDU size			RBS-1963
– RLC PDU size						144 bits			RBS-1964
– Include in scheduling info						FALSE			RBS-1965
– MAC logical channel priority						3			RBS-1966
– Downlink RLC logical channel info									RBS-1967
– Number of RLC logical channels						1			RBS-1968
– Downlink transport channel type						HS-DSCH			RBS-1969
– DL DCH Transport channel identity						Not Present			RBS-1970
– DL DSCH Transport channel identity						Not Present			RBS-1971
– DL HS-DSCH MAC-d flow identity						1			RBS-1972
– Logical channel identity						3			RBS-1973
– RB identity						4 (AM DCCH for NAS Low Priority)			RBS-1974
– RB mapping info									RBS-1975
– Information for each multiplexing option						1 RBMuxOption			RBS-1976
– RLC logical channel mapping indicator						Not Present			RBS-1977
– Number of uplink RLC logical channels						1			RBS-1978
– Uplink transport channel type						E-DCH			RBS-1979
– Logical channel identity						4			RBS-1980
– E-DCH MAC-d flow identity						1			RBS-1981
– CHOICE RLC PDU size						Fixed size		Rel-8	RBS-1982
– DDI						4			RBS-1983
– RLC PDU size list						1 RLC PDU size			RBS-1984
– RLC PDU size						144 bits			RBS-1985
– Include in scheduling info						FALSE			RBS-1986
– MAC logical channel priority						4			RBS-1987
– Downlink RLC logical channel info									RBS-1988
– Number of RLC logical channels						1			RBS-1989
– Downlink transport channel type						HS-DSCH			RBS-1990
– DL DCH Transport channel identity						Not Present			RBS-1991
– DL DSCH Transport channel identity						Not Present			RBS-1992
– DL HS-DSCH MAC-d flow identity						1			RBS-1993
– Logical channel identity						4			RBS-1994
RB information to be affected			A17b, A17c, A22, A28a					Rel-7	RBS-1995
			A25 A25c					Rel-8 Rel-9	RBS-1996
– RB identity						1 (UM DCCH for RRC)			RBS-1997
– RB mapping info									RBS-1998
– Information for each multiplexing option						1 RBMuxOption			RBS-1999
– RLC logical channel mapping indicator						Not Present			RBS-2000
– Number of uplink RLC logical channels						1			RBS-2001
– Uplink transport channel type						E-DCH			RBS-2002
– Logical channel identity						1			RBS-2003
– E-DCH MAC-d flow identity						1			RBS-2004
– CHOICE RLC PDU size						Fixed size		Rel-8	RBS-2005
– DDI						1			RBS-2006
– RLC PDU size list						1 RLC PDU size			RBS-2007
– RLC PDU size						144 bits			RBS-2008
– Include in scheduling info						FALSE			RBS-2009
– MAC logical channel priority						1			RBS-2010
– Downlink RLC logical channel info									RBS-2011
– Number of RLC logical channels						1			RBS-2012
– Downlink transport channel type						HS-DSCH			RBS-2013
– DL DCH Transport channel identity						Not present			RBS-2014
– DL DSCH Transport channel identity						Not present			RBS-2015
– CHOICE DL MAC header type						MAC-ehs			RBS-2016
– DL HS-DSCH MAC-ehs Queue Id						1			RBS-2017
– Logical channel identity						1			RBS-2018
– RB identity						2 (AM DCCH for RRC)			RBS-2019
– RB mapping info									RBS-2020
– Information for each multiplexing option						1 RBMuxOption			RBS-2021
– RLC logical channel mapping indicator						Not Present			RBS-2022
– Number of uplink RLC logical channels						1			RBS-2023
– Uplink transport channel type						E-DCH			RBS-2024
– Logical channel identity						2			RBS-2025
– E-DCH MAC-d flow identity						1			RBS-2026
– CHOICE RLC PDU size						Fixed size		Rel-8	RBS-2027
– DDI						2			RBS-2028
– RLC PDU size list						1 RLC PDU size			RBS-2029
– RLC PDU size						144 bits			RBS-2030
– Include in scheduling info						FALSE			RBS-2031
– MAC logical channel priority						2			RBS-2032
– Downlink RLC logical channel info									RBS-2033
– Number of RLC logical channels						1			RBS-2034
– Downlink transport channel type						HS-DSCH			RBS-2035
– DL DCH Transport channel identity						Not Present			RBS-2036
– DL DSCH Transport channel identity						Not Present			RBS-2037
– CHOICE DL MAC header type						MAC-ehs			RBS-2038
– DL HS-DSCH MAC-ehs Queue Id						1			RBS-2039
– Logical channel identity						2			RBS-2040
– RB identity						3 (AM DCCH for NAS High Priority)			RBS-2041
– RB mapping info									RBS-2042
– Information for each multiplexing option						1 RBMuxOption			RBS-2043
– RLC logical channel mapping indicator						Not Present			RBS-2044
– Number of uplink RLC logical channels						1			RBS-2045
– Uplink transport channel type						E-DCH			RBS-2046
– Logical channel identity						3			RBS-2047
– E-DCH MAC-d flow identity						1			RBS-2048
– CHOICE RLC PDU size						Fixed size		Rel-8	RBS-2049
– DDI						3			RBS-2050
– RLC PDU size list						1 RLC PDU size			RBS-2051
– RLC PDU size						144 bits			RBS-2052
– Include in scheduling info						FALSE			RBS-2053
– MAC logical channel priority						3			RBS-2054
– Downlink RLC logical channel info									RBS-2055
– Number of RLC logical channels						1			RBS-2056
– Downlink transport channel type						HS-DSCH			RBS-2057
– DL DCH Transport channel identity						Not Present			RBS-2058
– DL DSCH Transport channel identity						Not Present			RBS-2059
– CHOICE DL MAC header type						MAC-ehs			RBS-2060
– DL HS-DSCH MAC-ehs Queue Id						1			RBS-2061
– Logical channel identity						3			RBS-2062
– RB identity						4 (AM DCCH for NAS Low Priority)			RBS-2063
– RB mapping info									RBS-2064
– Information for each multiplexing option						1 RBMuxOption			RBS-2065
– RLC logical channel mapping indicator						Not Present			RBS-2066
– Number of uplink RLC logical channels						1			RBS-2067
– Uplink transport channel type						E-DCH			RBS-2068
– Logical channel identity						4			RBS-2069
– E-DCH MAC-d flow identity						1			RBS-2070
– CHOICE RLC PDU size						Fixed size		Rel-8	RBS-2071
– DDI						4			RBS-2072
– RLC PDU size list						1 RLC PDU size			RBS-2073
– RLC PDU size						144 bits			RBS-2074
– Include in scheduling info						FALSE			RBS-2075
– MAC logical channel priority						4			RBS-2076
– Downlink RLC logical channel info									RBS-2077
– Number of RLC logical channels						1			RBS-2078
– Downlink transport channel type						HS-DSCH			RBS-2079
– DL DCH Transport channel identity						Not Present			RBS-2080
– DL DSCH Transport channel identity						Not Present			RBS-2081
– CHOICE DL MAC header type						MAC-ehs			RBS-2082
– DL HS-DSCH MAC-ehs Queue Id						1			RBS-2083
– Logical channel identity						4			RBS-2084
RB information to be affected			A27, A27a , A33, A34, A36, A37					Rel-8 Rel-10	RBS-2085
– RB identity						1 (UM DCCH for RRC)			RBS-2086
– RB mapping info									RBS-2087
– Information for each multiplexing option						1 RBMuxOption			RBS-2088
– RLC logical channel mapping indicator						Not Present			RBS-2089
– Number of uplink RLC logical channels						1			RBS-2090
– Uplink transport channel type						E-DCH			RBS-2091
– Logical channel identity						1			RBS-2092
– E-DCH MAC-d flow identity						1			RBS-2093
– CHOICE RLC PDU size						Fixed size			RBS-2094
– DDI						Not Present			RBS-2095
– RLC PDU size list						1 RLC PDU size			RBS-2096
– RLC PDU size						144 bits			RBS-2097
– Include in scheduling info						FALSE			RBS-2098
– MAC logical channel priority						1			RBS-2099
– Downlink RLC logical channel info									RBS-2100
– Number of RLC logical channels						1			RBS-2101
– Downlink transport channel type						HS-DSCH			RBS-2102
– DL DCH Transport channel identity						Not present			RBS-2103
– DL DSCH Transport channel identity						Not present			RBS-2104
– CHOICE DL MAC header type						MAC-ehs			RBS-2105
– DL HS-DSCH MAC-ehs Queue Id						1			RBS-2106
– Logical channel identity						1			RBS-2107
– RB identity						2 (AM DCCH for RRC)			RBS-2108
– RB mapping info									RBS-2109
– Information for each multiplexing option						1 RBMuxOption			RBS-2110
– RLC logical channel mapping indicator						Not Present			RBS-2111
– Number of uplink RLC logical channels						1			RBS-2112
– Uplink transport channel type						E-DCH			RBS-2113
– Logical channel identity						2			RBS-2114
– E-DCH MAC-d flow identity						1			RBS-2115
– CHOICE RLC PDU size						Fixed size			RBS-2116
– DDI						Not Present			RBS-2117
– RLC PDU size list						1 RLC PDU size			RBS-2118
– RLC PDU size						144 bits			RBS-2119
– Include in scheduling info						FALSE			RBS-2120
– MAC logical channel priority						2			RBS-2121
– Downlink RLC logical channel info									RBS-2122
– Number of RLC logical channels						1			RBS-2123
– Downlink transport channel type						HS-DSCH			RBS-2124
– DL DCH Transport channel identity						Not Present			RBS-2125
– DL DSCH Transport channel identity						Not Present			RBS-2126
– CHOICE DL MAC header type						MAC-ehs			RBS-2127
– DL HS-DSCH MAC-ehs Queue Id						1			RBS-2128
– Logical channel identity						2			RBS-2129
– RB identity						3 (AM DCCH for NAS High Priority)			RBS-2130
– RB mapping info									RBS-2131
– Information for each multiplexing option						1 RBMuxOption			RBS-2132
– RLC logical channel mapping indicator						Not Present			RBS-2133
– Number of uplink RLC logical channels						1			RBS-2134
– Uplink transport channel type						E-DCH			RBS-2135
– Logical channel identity						3			RBS-2136
– E-DCH MAC-d flow identity						1			RBS-2137
– CHOICE RLC PDU size						Fixed size			RBS-2138
– DDI						Not Present			RBS-2139
– RLC PDU size list						1 RLC PDU size			RBS-2140
– RLC PDU size						144 bits			RBS-2141
– Include in scheduling info						FALSE			RBS-2142
– MAC logical channel priority						3			RBS-2143
– Downlink RLC logical channel info									RBS-2144
– Number of RLC logical channels						1			RBS-2145
– Downlink transport channel type						HS-DSCH			RBS-2146
– DL DCH Transport channel identity						Not Present			RBS-2147
– DL DSCH Transport channel identity						Not Present			RBS-2148
– CHOICE DL MAC header type						MAC-ehs			RBS-2149
– DL HS-DSCH MAC-ehs Queue Id						1			RBS-2150
– Logical channel identity						3			RBS-2151
– RB identity						4 (AM DCCH for NAS Low Priority)			RBS-2152
– RB mapping info									RBS-2153
– Information for each multiplexing option						1 RBMuxOption			RBS-2154
– RLC logical channel mapping indicator						Not Present			RBS-2155
– Number of uplink RLC logical channels						1			RBS-2156
– Uplink transport channel type						E-DCH			RBS-2157
– Logical channel identity						4			RBS-2158
– E-DCH MAC-d flow identity						1			RBS-2159
– CHOICE RLC PDU size						Fixed size			RBS-2160
– DDI						Not Present			RBS-2161
– RLC PDU size list						1 RLC PDU size			RBS-2162
– RLC PDU size						144 bits			RBS-2163
– Include in scheduling info						FALSE			RBS-2164
– MAC logical channel priority						4			RBS-2165
– Downlink RLC logical channel info									RBS-2166
– Number of RLC logical channels						1			RBS-2167
– Downlink transport channel type						HS-DSCH			RBS-2168
– DL DCH Transport channel identity						Not Present			RBS-2169
– DL DSCH Transport channel identity						Not Present			RBS-2170
– CHOICE DL MAC header type						MAC-ehs			RBS-2171
– DL HS-DSCH MAC-ehs Queue Id						1			RBS-2172
– Logical channel identity						4			RBS-2173
RB information to be affected			A30					Rel-8	RBS-2174
– RB identity						1 (UM DCCH for RRC)			RBS-2175
– RB mapping info									RBS-2176
– Information for each multiplexing option						1 RBMuxOption			RBS-2177
– RLC logical channel mapping indicator						Not Present			RBS-2178
– Number of uplink RLC logical channels						1			RBS-2179
– Uplink transport channel type						E-DCH			RBS-2180
– Logical channel identity						1			RBS-2181
– E-DCH MAC-d flow identity						3			RBS-2182
– CHOICE RLC PDU size						Fixed size			RBS-2183
– DDI						0 (Not applicable for MAC-i/is)			RBS-2184
– RLC PDU size list						1 RLC PDU size			RBS-2185
– RLC PDU size						144 bits			RBS-2186
– Include in scheduling info						FALSE			RBS-2187
– MAC logical channel priority						1			RBS-2188
– Downlink RLC logical channel info									RBS-2189
– Number of RLC logical channels						1			RBS-2190
– Downlink transport channel type						HS-DSCH			RBS-2191
– DL DCH Transport channel identity						Not present			RBS-2192
– DL DSCH Transport channel identity						Not present			RBS-2193
– CHOICE DL MAC header type						MAC-ehs			RBS-2194
– DL HS-DSCH MAC-ehs Queue Id						3			RBS-2195
– Logical channel identity						1			RBS-2196
– RB identity						2 (AM DCCH for RRC)			RBS-2197
– RB mapping info									RBS-2198
– Information for each multiplexing option						1 RBMuxOption			RBS-2199
– RLC logical channel mapping indicator						Not Present			RBS-2200
– Number of uplink RLC logical channels						1			RBS-2201
– Uplink transport channel type						E-DCH			RBS-2202
– Logical channel identity						2			RBS-2203
– E-DCH MAC-d flow identity						3			RBS-2204
– CHOICE RLC PDU size						Fixed size			RBS-2205
– DDI						0 (Not applicable for MAC-i/is)			RBS-2206
– RLC PDU size list						1 RLC PDU size			RBS-2207
– RLC PDU size						144 bits			RBS-2208
– Include in scheduling info						FALSE			RBS-2209
– MAC logical channel priority						2			RBS-2210
– Downlink RLC logical channel info									RBS-2211
– Number of RLC logical channels						1			RBS-2212
– Downlink transport channel type						HS-DSCH			RBS-2213
– DL DCH Transport channel identity						Not Present			RBS-2214
– DL DSCH Transport channel identity						Not Present			RBS-2215
– CHOICE DL MAC header type						MAC-ehs			RBS-2216
– DL HS-DSCH MAC-ehs Queue Id						3			RBS-2217
– Logical channel identity						2			RBS-2218
– RB identity						3 (AM DCCH for NAS High Priority)			RBS-2219
– RB mapping info									RBS-2220
– Information for each multiplexing option						1 RBMuxOption			RBS-2221
– RLC logical channel mapping indicator						Not Present			RBS-2222
– Number of uplink RLC logical channels						1			RBS-2223
– Uplink transport channel type						E-DCH			RBS-2224
– Logical channel identity						3			RBS-2225
– E-DCH MAC-d flow identity						3			RBS-2226
– CHOICE RLC PDU size						Fixed size		Rel-8	RBS-2227
– DDI						0 (Not applicable for MAC-i/is)			RBS-2228
– RLC PDU size list						1 RLC PDU size			RBS-2229
– RLC PDU size						144 bits			RBS-2230
– Include in scheduling info						FALSE			RBS-2231
– MAC logical channel priority						3			RBS-2232
– Downlink RLC logical channel info									RBS-2233
– Number of RLC logical channels						1			RBS-2234
– Downlink transport channel type						HS-DSCH			RBS-2235
– DL DCH Transport channel identity						Not Present			RBS-2236
– DL DSCH Transport channel identity						Not Present			RBS-2237
– CHOICE DL MAC header type						MAC-ehs			RBS-2238
– DL HS-DSCH MAC-ehs Queue Id						3			RBS-2239
– Logical channel identity						3			RBS-2240
– RB identity						4 (AM DCCH for NAS Low Priority)			RBS-2241
– RB mapping info									RBS-2242
– Information for each multiplexing option						1 RBMuxOption			RBS-2243
– RLC logical channel mapping indicator						Not Present			RBS-2244
– Number of uplink RLC logical channels						1			RBS-2245
– Uplink transport channel type						E-DCH			RBS-2246
– Logical channel identity						4			RBS-2247
– E-DCH MAC-d flow identity						3			RBS-2248
– CHOICE RLC PDU size						Fixed size		Rel-8	RBS-2249
– DDI						4			RBS-2250
– RLC PDU size list						1 RLC PDU size			RBS-2251
– RLC PDU size						144 bits			RBS-2252
– Include in scheduling info						FALSE			RBS-2253
– MAC logical channel priority						4			RBS-2254
– Downlink RLC logical channel info									RBS-2255
– Number of RLC logical channels						1			RBS-2256
– Downlink transport channel type						HS-DSCH			RBS-2257
– DL DCH Transport channel identity						Not Present			RBS-2258
– DL DSCH Transport channel identity						Not Present			RBS-2259
– CHOICE DL MAC header type						MAC-ehs			RBS-2260
– DL HS-DSCH MAC-ehs Queue Id						3			RBS-2261
– Logical channel identity						4			RBS-2262
Downlink counter synchronization info			A1, A2, A3, A4, A5, A6, A7, A8, A11			Not Present			RBS-2263
			, A9, A10					Rel-5	RBS-2264
			, A12, A13, A14, A15, A16					Rel-6	RBS-2265
			, A17, A17a, A17b, A17c, A17d, A17e, A17f, A18, A19, A19a, A19b, A20, A21, A22, A24					Rel-7	RBS-2266
			, A23, A28a					Rel-7 Rel-8	RBS-2267
			, A25, A25a, A25b, A26, A27, A27a, A28, A29, A30					Rel-8	RBS-2268
			, A31, A32, A25c , A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-2269
PDCP ROHC target mode			A9, A10			Not Present		Rel-5	RBS-2270
PDCP ROHC target mode			, A12, A13, A14, A15, A16			Not Present		Rel-6	RBS-2271
			, A17, A17a, A17b, A17c, A17d, A17e, A17f, A18, A19, A19a, A19b, A20, A21, A22, A24					Rel-7	RBS-2272
			, A23, A28a					Rel-7 Rel-8	RBS-2273
			, A25, A25a, A25b, A26, A27, A27a, A28, A29, A30					Rel-8	RBS-2274
			, A31, A32, A25c , A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-2275
UL Transport channel information for all transport channels			A1, A2, A3, A4, A5, A6, A7, A8, A11						RBS-2276
UL Transport channel information for all transport channels			, A9, A10					Rel-5	RBS-2277
			, A17, A17a, A17f, A18					Rel-7	RBS-2278
			, A25a, A28					Rel-8	RBS-2279
			, A31, A32 , A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-2280
– PRACH TFCS						Not Present			RBS-2281
– CHOICE mode						FDD			RBS-2282
– TFC subset						Not Present			RBS-2283
– UL DCH TFCS									RBS-2284
– CHOICE TFCI signalling						Normal			RBS-2285
– TFCI Field 1 information									RBS-2286
– CHOICE TFCS representation						Complete reconfiguration			RBS-2287
– TFCS complete reconfigure information									RBS-2288
– CHOICE CTFC Size						Number of bits used must be enough to cover all combinations of CTFC from clause 6.10.2.4 Parameter Set.			RBS-2289
– CTFC information						This IE is repeated for TFC numbers and reference to clause 6.10.2.4 Parameter Set			RBS-2290
– CTFC						Reference to clause 6.10.2.4 Parameter Set			RBS-2291
– Power offset information									RBS-2292
– CHOICE Gain Factors						Computed Gain Factors(The last TFC is set to Signalled Gain Factors)			RBS-2293
– Gain factor βc						11 (below 64 kbps) 9 (equal or higher than 64 kbps) when HSDPA is not configured 9 (equal or higher than 64 kbps and below 384 kbps) when HSDPA is also configured 6 (equal or higher than 384 kbps) when HSDPA is also configured (Not Present if the CHOICE Gain Factors is set to Computed Gain Factors)			RBS-2294
– Gain factor βd						15 (Not Present if the CHOICE Gain Factors is set to Computed Gain Factors)			RBS-2295
– Reference TFC ID						0			RBS-2296
– CHOICE mode						FDD			RBS-2297
– Power offset P p-m						Not Present			RBS-2298
UL Transport channel information for all transport channels			A12,					Rel-6	RBS-2299
			A19					Rel-7	RBS-2300
– PRACH TFCS						Not Present			RBS-2301
– CHOICE mode						FDD			RBS-2302
– TFC subset						Not Present			RBS-2303
– UL DCH TFCS									RBS-2304
– CHOICE TFCI signalling						Normal			RBS-2305
– TFCI Field 1 information									RBS-2306
– CHOICE TFCS representation						Complete reconfiguration			RBS-2307
– TFCS complete reconfigure information									RBS-2308
– CHOICE CTFC Size						ctfc2bit			RBS-2309
– CTFC information									RBS-2310
– CTFC						0 ((UL DCH RAB, DCCH)=(TF0, TF0))			RBS-2311
– Power offset information									RBS-2312
– CHOICE Gain Factors						Computed Gain Factors			RBS-2313
– CTFC						1 ((UL DCH RAB, DCCH)=(TF0, TF1))			RBS-2314
– Power offset information									RBS-2315
– CHOICE Gain Factors						Signalled Gain Factors			RBS-2316
– Gain factor βc						11 (below 64 kbps) 9 (equal or higher than 64 kbps) when HSDPA is not configured 9 (equal or higher than 64 kbps and below 384 kbps) when HSDPA is also configured 6 (equal or higher than 384 kbps) when HSDPA is also configured (Not Present if the CHOICE Gain Factors is set to Computed Gain Factors)			RBS-2317
– Gain factor βd						15			RBS-2318
– Reference TFC ID						0			RBS-2319
– CHOICE mode						FDD			RBS-2320
– Power offset P p-m						Not Present			RBS-2321
UL Transport channel information for all transport channels			A13, A14, A15, A16			Not Present		Rel-6	RBS-2322
			, A17b, A17c, A17d, A17e, A19a, A19b, A20, A21, A22, A24					Rel-7	RBS-2323
			, A23, A28a,					Rel-7 Rel-8	RBS-2324
			, A25, A25b, A26, A27, A27a, A29, A30					Rel-8	RBS-2325
			, A25c					Rel-9	RBS-2326
Deleted UL TrCH information			A1, A2, A3, A4, A5, A6, A7, A8, A11			Not Present			RBS-2327
			, A9, A10					Rel-5	RBS-2328
			, A12					Rel-6	RBS-2329
			, A17, A17a, A17f, A18, A19, A20, A21, A24					Rel-7	RBS-2330
			, A23,					Rel-7 Rel-8	RBS-2331
			, A28, A29					Rel-8	RBS-2332
			A35, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-10 Rel-11	RBS-2333
Deleted UL TrCH information			A13, A14, A15, A16					Rel-6	RBS-2334
			A17b, A17c, A17d, A17e, A19a, A19b, A22, A26, A27, A27a, A28a					Rel-7	RBS-2335
			A25, A25b					Rel-8	RBS-2336
			, A25c, A31, A32 , A33, A34, A36, A37					Rel-9 Rel-10	RBS-2337
– Uplink transport channel type						DCH			RBS-2338
– UL transport channel identity						5			RBS-2339
Deleted UL TrCH information – Uplink transport channel type – E-DCH MAC-d flow identity			A30			e_dch 1		Rel-8	RBS-2339a
Added or Reconfigured UL TrCH information			A1, A3 A4, A5, A6, A7			1 DCH added, 1 DCH reconfigured (if from cell_DCH) OR 2 DCHs added (if from cell_FACH)			RBS-2340
Added or Reconfigured UL TrCH information			, A9, A10					Rel-5	RBS-2341
			, A17, A17a, A18,					Rel-7	RBS-2342
			, A28					Rel-8	RBS-2343
– Uplink transport channel type						DCH			RBS-2344
– UL Transport channel identity						1			RBS-2345
– TFS									RBS-2346
– CHOICE Transport channel type						Dedicated transport channels			RBS-2347
– Dynamic Transport format information									RBS-2348
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2349
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2350
– Transmission Time Interval						Not Present			RBS-2351
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-2352
– CHOICE Logical channel list						All			RBS-2353
– Semi-static Transport Format information									RBS-2354
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2355
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2356
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2357
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2358
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2359
– Uplink transport channel type						DCH			RBS-2360
– UL Transport channel identity						5			RBS-2361
– TFS									RBS-2362
– CHOICE Transport channel type						Dedicated transport channels			RBS-2363
– Dynamic Transport format information									RBS-2364
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2365
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2366
– Transmission Time Interval						Not Present			RBS-2367
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-2368
– CHOICE Logical channel list						All			RBS-2369
– Semi-static Transport Format information									RBS-2370
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2371
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2372
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2373
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2374
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2375
Added or Reconfigured UL TrCH information			A11			1 DCH added for DTCH			RBS-2376
– Uplink transport channel type						DCH			RBS-2377
– UL Transport channel identity						4			RBS-2378
– TFS									RBS-2379
– CHOICE Transport channel type						Dedicated transport channels			RBS-2380
– Dynamic Transport format information									RBS-2381
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2382
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2383
– Transmission Time Interval						Not Present			RBS-2384
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-2385
– CHOICE Logical channel list						All			RBS-2386
– Semi-static Transport Format information									RBS-2387
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2388
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2389
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2390
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2391
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2392
Added or Reconfigured UL TrCH information			A2, A8			4 TrCHs(DCH for DCCH and 3DCHs for DTCH)			RBS-2393
– Uplink transport channel type						DCH			RBS-2394
– UL Transport channel identity						5			RBS-2395
– TFS									RBS-2396
– CHOICE Transport channel type						Dedicated transport channels			RBS-2397
– Dynamic Transport format information									RBS-2398
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2399
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2400
– Transmission Time Interval						Not Present			RBS-2401
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-2402
– CHOICE Logical channel list						All			RBS-2403
– Semi-static Transport Format information									RBS-2404
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2405
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2406
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2407
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2408
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2409
– Uplink transport channel type						DCH			RBS-2410
– UL Transport channel identity						1			RBS-2411
– TFS									RBS-2412
– CHOICE Transport channel type						Dedicated transport channels			RBS-2413
– Dynamic Transport format information									RBS-2414
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2415
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2416
– Transmission Time Interval						Not Present			RBS-2417
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-2418
– CHOICE Logical channel list						All			RBS-2419
– Semi-static Transport Format information									RBS-2420
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2421
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2422
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2423
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2424
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2425
– Uplink transport channel type						DCH			RBS-2426
– UL Transport channel identity						2			RBS-2427
– TFS									RBS-2428
– CHOICE Transport channel type						Dedicated transport channels			RBS-2429
– Dynamic Transport format information									RBS-2430
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2431
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2432
– Transmission Time Interval						Not Present			RBS-2433
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-2434
– CHOICE Logical channel list						All			RBS-2435
– Semi-static Transport Format information									RBS-2436
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2437
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2438
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2439
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2440
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2441
– Uplink transport channel type						DCH			RBS-2442
– UL Transport channel identity						3			RBS-2443
– TFS									RBS-2444
– CHOICE Transport channel type						Dedicated transport channels			RBS-2445
– Dynamic Transport format information									RBS-2446
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2447
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2448
– Transmission Time Interval						Not Present			RBS-2449
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-2450
– CHOICE Logical channel list						All			RBS-2451
– Semi-static Transport Format information									RBS-2452
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2453
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2454
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2455
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2456
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2457
Added or Reconfigured UL TrCH information			A12			1 E-DCH added, 1 DCH added, 1 DCH reconfigured		Rel-6	RBS-2458
			A19					Rel-7	RBS-2459
– Uplink transport channel type						E-DCH			RBS-2460
– CHOICE UL parameters						E-DCH			RBS-2461
– UL MAC header type						Not present		Rel-8	RBS-2462
– UL MAC header type			MAC-I-FIXED, MAC-I-FLEX			MAC-i/is		Rel-8	RBS-2463
– E-DCH Transmission Time Interval						set to 2ms if supported by the UE E-DCH category, or 10ms if the UE E-DCH category does not support 2ms TTI			RBS-2464
– HARQ info for E-DCH									RBS-2465
– HARQ RV Configuration						rvtable			RBS-2466
– Added or reconfigured E-DCH MAC-d flow									RBS-2467
– E-DCH MAC-d flow identity						2			RBS-2468
– E-DCH MAC-d flow power offset						0			RBS-2469
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2470
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2471
– CHOICE transmission grant type						Scheduled grant info			RBS-2472
– Uplink transport channel type						DCH			RBS-2473
– UL Transport channel identity						1			RBS-2474
– TFS									RBS-2475
– CHOICE Transport channel type						Dedicated transport channels			RBS-2476
– Dynamic Transport format information									RBS-2477
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2478
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2479
– Transmission Time Interval						Not Present			RBS-2480
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-2481
– CHOICE Logical channel list						All			RBS-2482
– Semi-static Transport Format information									RBS-2483
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2484
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2485
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2486
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2487
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2488
– Uplink transport channel type						DCH			RBS-2489
– UL Transport channel identity						5			RBS-2490
– TFS									RBS-2491
– CHOICE Transport channel type						Dedicated transport channels			RBS-2492
– Dynamic Transport format information									RBS-2493
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2494
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2495
– Transmission Time Interval						Not Present			RBS-2496
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-2497
– CHOICE Logical channel list						All			RBS-2498
– Semi-static Transport Format information									RBS-2499
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2500
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2501
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2502
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2503
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2504
Added or Reconfigured UL TrCH information			A13, A14			1 E-DCH added with one DCCH MAC-d flow and one DTCH MAC-d flow		Rel-6	RBS-2505
			, A17b, A17c, A17d, A17e, A19a, A20, A28a					Rel-7	RBS-2506
			, A25, A25b, A27, A27a					Rel-8	RBS-2507
			, A25c, A31, A32 , A33, A34, A36, A37					Rel-9 Rel-10	RBS-2508
– Uplink transport channel type						E-DCH			RBS-2509
– CHOICE UL parameters						E-DCH			RBS-2510
– UL MAC header type						Not present		Rel-8	RBS-2511
– UL MAC header type			MAC-I-FIXED, MAC-I-FLEX			MAC-i/is		Rel-8	RBS-2512
– E-DCH Transmission Time Interval						set to 2ms if supported by the UE E-DCH category, or 10ms if the UE E-DCH category does not support 2ms TTI			RBS-2513
– HARQ info for E-DCH									RBS-2514
– HARQ RV Configuration						rvtable			RBS-2515
– Added or reconfigured E-DCH MAC-d flow						(for DCCH)			RBS-2516
– E-DCH MAC-d flow identity						1			RBS-2517
– E-DCH MAC-d flow power offset						0			RBS-2518
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2519
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2520
– CHOICE transmission grant type						Non-scheduled grant info			RBS-2521
– Max MAC-e PDU contents size			MAC-I-FIXED, MAC-I-FLEX			168 bits		Rel-8	RBS-2522
– Max MAC-e PDU contents size						162 bits			RBS-2523
– 2 ms non-scheduled transmission grant HARQ process allocation						Not Present			RBS-2524
– Added or reconfigured E-DCH MAC-d flow						(for DTCH)			RBS-2525
– E-DCH MAC-d flow identity						2			RBS-2526
– E-DCH MAC-d flow power offset						0			RBS-2527
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2528
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2529
– CHOICE transmission grant type						Scheduled grant info			RBS-2530
Added or Reconfigured UL TrCH information			A15			1 E-DCH added with one DCCH MAC-d flow and two DTCH MAC-d flows		Rel-6	RBS-2531
– Uplink transport channel type						E-DCH			RBS-2532
– CHOICE UL parameters						E-DCH			RBS-2533
– UL MAC header type						Not present		Rel-8	RBS-2534
– UL MAC header type			MAC-I-FIXED, MAC-I-FLEX			MAC-i/is		Rel-8	RBS-2535
– E-DCH Transmission Time Interval						set to 2ms if supported by the UE E-DCH category, or 10ms if the UE E-DCH category does not support 2ms TTI			RBS-2536
– HARQ info for E-DCH									RBS-2537
– HARQ RV Configuration						rvtable			RBS-2538
– Added or reconfigured E-DCH MAC-d flow						(for DCCH)			RBS-2539
– E-DCH MAC-d flow identity						1			RBS-2540
– E-DCH MAC-d flow power offset						0			RBS-2541
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2542
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2543
– CHOICE transmission grant type						Non-scheduled grant info			RBS-2544
– Max MAC-e PDU contents size						162 bits			RBS-2545
– Max MAC-e PDU contents size			MAC-I-FIXED, MAC-I-FLEX			168 bits		Rel-8	RBS-2546
– 2 ms non-scheduled transmission grant HARQ process allocation						Not Present			RBS-2547
– Added or reconfigured E-DCH MAC-d flow						(for first DTCH)			RBS-2548
– E-DCH MAC-d flow identity						2			RBS-2549
– E-DCH MAC-d flow power offset						0			RBS-2550
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2551
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2552
– CHOICE transmission grant type						Scheduled grant info			RBS-2553
– Added or reconfigured E-DCH MAC-d flow						(for second DTCH)			RBS-2554
– E-DCH MAC-d flow identity						3			RBS-2555
– E-DCH MAC-d flow power offset						0			RBS-2556
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2557
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2558
– CHOICE transmission grant type						Scheduled grant info			RBS-2559
Added or Reconfigured UL TrCH information			A16			1 E-DCH added with one DCCH MAC-d flow and two DTCH MAC-d flows		Rel-6	RBS-2560
			, A19b, A21, A22					Rel-7	RBS-2561
– Uplink transport channel type						E-DCH			RBS-2562
– CHOICE UL parameters						E-DCH			RBS-2563
– UL MAC header type						Not present		Rel-8	RBS-2564
– UL MAC header type			MAC-I-FIXED, MAC-I-FLEX			MAC-i/is		Rel-8	RBS-2565
– CHOICE mode						FDD		Rel-7	RBS-2566
– E-DCH Transmission Time Interval						set to 2ms if supported by the UE E-DCH category, or 10ms if the UE E-DCH category does not support 2ms TTI			RBS-2567
– HARQ info for E-DCH									RBS-2568
– HARQ RV Configuration						rvtable			RBS-2569
– Added or reconfigured E-DCH MAC-d flow						(for DCCH)			RBS-2570
– E-DCH MAC-d flow identity						1			RBS-2571
– E-DCH MAC-d flow power offset						0			RBS-2572
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2573
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2574
– CHOICE transmission grant type						Non-scheduled grant info			RBS-2575
– Max MAC-e PDU contents size						162 bits			RBS-2576
– Max MAC-e PDU contents size			MAC-I-FIXED, MAC-I-FLEX			168 bits		Rel-8	RBS-2577
– 2 ms non-scheduled transmission grant HARQ process allocation						Not Present			RBS-2578
– Added or reconfigured E-DCH MAC-d flow						(for first DTCH)			RBS-2579
– E-DCH MAC-d flow identity						2			RBS-2580
– E-DCH MAC-d flow power offset						0			RBS-2581
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2582
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2583
– CHOICE transmission grant type						Scheduled grant info			RBS-2584
– Added or reconfigured E-DCH MAC-d flow						(for second DTCH)			RBS-2585
– E-DCH MAC-d flow identity						4			RBS-2586
– E-DCH MAC-d flow power offset						0			RBS-2587
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2588
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2589
– CHOICE transmission grant type						Scheduled grant info			RBS-2590
Added or Reconfigured UL TrCH information			A23			1 E-DCH added with one DCCH MAC-d flow and one DTCH MAC-d flow		Rel-7 Rel-8	RBS-2591
– Uplink transport channel type						E-DCH			RBS-2592
– CHOICE UL parameters						E-DCH			RBS-2593
– UL MAC header type						Not present		Rel-8	RBS-2594
– UL MAC header type			MAC-I-FIXED, MAC-I-FLEX			MAC-i/is		Rel-8	RBS-2595
– E-DCH Transmission Time Interval						set to 2ms if supported by the UE E-DCH category, or 10ms if the UE E-DCH category does not support 2ms TTI			RBS-2596
– HARQ info for E-DCH									RBS-2597
– HARQ RV Configuration						rvtable			RBS-2598
– Added or reconfigured E-DCH MAC-d flow						(for DCCH)			RBS-2599
– E-DCH MAC-d flow identity						1			RBS-2600
– E-DCH MAC-d flow power offset						0			RBS-2601
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2602
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2603
– CHOICE transmission grant type						Non-scheduled grant info			RBS-2604
– Max MAC-e PDU contents size						162 bits		Rel-6	RBS-2605
– Max MAC-e PDU contents size			MAC-I-FIXED, MAC-I-FLEX			168 bits		Rel-8	RBS-2606
– 2 ms non-scheduled transmission grant HARQ process allocation						‘01000000’B if 2ms TTI configured otherwise Not Present			RBS-2607
– Added or reconfigured E-DCH MAC-d flow						(for DTCH)			RBS-2608
– E-DCH MAC-d flow identity						2			RBS-2609
– E-DCH MAC-d flow power offset						0			RBS-2610
– E-DCH MAC-d flow maximum number of retransmissions						3 if 2ms TTI configured, otherwise 1			RBS-2611
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2612
– CHOICE transmission grant type						Non-scheduled grant info			RBS-2613
– Max MAC-e PDU contents size						546 bits		Rel-6	RBS-2614
– Max MAC-e PDU contents size			MAC-I-FIXED, MAC-I-FLEX			552 bits		Rel-8	RBS-2615
Added or Reconfigured UL TrCH information			A26			1 E-DCH added with one DCCH MAC-d flow and three DTCH MAC-d flows		Rel-8	RBS-2616
– Uplink transport channel type						E-DCH			RBS-2617
– CHOICE UL parameters						E-DCH			RBS-2618
– UL MAC header type						Not present			RBS-2619
– UL MAC header type						MAC-i/is			RBS-2620
– CHOICE mode						FDD		Rel-7	RBS-2621
– E-DCH Transmission Time Interval						set to 2ms if supported by the UE E-DCH category, or 10ms if the UE E-DCH category does not support 2ms TTI			RBS-2622
– HARQ info for E-DCH									RBS-2623
– HARQ RV Configuration						rvtable			RBS-2624
– Added or reconfigured E-DCH MAC-d flow						(for DCCH)			RBS-2625
– E-DCH MAC-d flow identity						1			RBS-2626
– E-DCH MAC-d flow power offset						0			RBS-2627
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2628
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2629
– CHOICE transmission grant type						Non-scheduled grant info			RBS-2630
– Max MAC-e PDU contents size						168 bits			RBS-2631
– 2 ms non-scheduled transmission grant HARQ process allocation						Not Present			RBS-2632
– Added or reconfigured E-DCH MAC-d flow						(for first DTCH)			RBS-2633
– E-DCH MAC-d flow identity						2			RBS-2634
– E-DCH MAC-d flow power offset						0			RBS-2635
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2636
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2637
– CHOICE transmission grant type						Scheduled grant info			RBS-2638
– Added or reconfigured E-DCH MAC-d flow						(for second DTCH)			RBS-2639
– E-DCH MAC-d flow identity						3			RBS-2640
– E-DCH MAC-d flow power offset						0			RBS-2641
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2642
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2643
– CHOICE transmission grant type						Scheduled grant info			RBS-2644
– Added or reconfigured E-DCH MAC-d flow						(for third DTCH)			RBS-2645
– E-DCH MAC-d flow identity						4			RBS-2646
– E-DCH MAC-d flow power offset						0			RBS-2647
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2648
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2649
– CHOICE transmission grant type						Scheduled grant info			RBS-2650
Added or Reconfigured UL TrCH information			A29			1 E-DCH added with one DTCH MAC-d flow		Rel-8	RBS-2651
– Uplink transport channel type						E-DCH			RBS-2652
– CHOICE UL parameters						E-DCH			RBS-2653
– UL MAC header type			MAC-I-FIXED, MAC-I-FLEX			MAC-i/is		Rel-8	RBS-2654
– E-DCH Transmission Time Interval						set to 2ms if supported by the UE E-DCH category, or 10ms if the UE E-DCH category does not support 2ms TTI			RBS-2655
– HARQ info for E-DCH									RBS-2656
– HARQ RV Configuration						rvtable			RBS-2657
– Added or reconfigured E-DCH MAC-d flow									RBS-2658
– E-DCH MAC-d flow identity						0			RBS-2659
– E-DCH MAC-d flow power offset						0			RBS-2660
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2661
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2662
– CHOICE transmission grant type						Scheduled grant info			RBS-2663
Added or Reconfigured UL TrCH information			A30			1 E-DCH added with one DCCH MAC-d flow and one DTCH MAC-d flow		Rel-8	RBS-2664
– Uplink transport channel type						E-DCH			RBS-2665
– CHOICE UL parameters						E-DCH			RBS-2666
– UL MAC header type			MAC-I-FIXED, MAC-I-FLEX			MAC-i/is			RBS-2667
– E-DCH Transmission Time Interval						set to 2ms if supported by the UE E-DCH category, or 10ms if the UE E-DCH category does not support 2ms TTI			RBS-2668
– HARQ info for E-DCH									RBS-2669
– HARQ RV Configuration						rvtable			RBS-2670
– Added or reconfigured E-DCH MAC-d flow						(for DCCH)			RBS-2671
– E-DCH MAC-d flow identity						3			RBS-2672
– E-DCH MAC-d flow power offset						0			RBS-2673
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2674
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2675
– CHOICE transmission grant type						Non-scheduled grant info			RBS-2676
– Max MAC-e PDU contents size						168 bits			RBS-2677
– 2 ms non-scheduled transmission grant HARQ process allocation						Not Present			RBS-2678
– Added or reconfigured E-DCH MAC-d flow						(for DTCH)			RBS-2679
– E-DCH MAC-d flow identity						2			RBS-2680
– E-DCH MAC-d flow power offset						0			RBS-2681
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2682
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2683
– CHOICE transmission grant type						Scheduled grant info			RBS-2684
Added or Reconfigured UL TrCH information			A17f, A35 A38, A39, A40, A41, A42, A43, A44, A45			1 E-DCH added, 1 DCH reconfigured		Rel-7 Rel-10 Rel-11	RBS-2685
– Uplink transport channel type						E-DCH			RBS-2686
– CHOICE UL parameters						E-DCH			RBS-2687
– UL MAC header type			MAC-I-FIXED, MAC-I-FLEX			MAC-i/is		Rel-8	RBS-2688
– E-DCH Transmission Time Interval						set to 2ms if supported by the UE E-DCH category, or 10ms if the UE E-DCH category does not support 2ms TTI			RBS-2689
– HARQ info for E-DCH									RBS-2690
– HARQ RV Configuration						rvtable			RBS-2691
– Added or reconfigured E-DCH MAC-d flow									RBS-2692
– E-DCH MAC-d flow identity						2			RBS-2693
– E-DCH MAC-d flow power offset						0			RBS-2694
– E-DCH MAC-d flow maximum number of retransmissions						7			RBS-2695
– E-DCH MAC-d flow multiplexing list						Not Present			RBS-2696
– CHOICE transmission grant type						Scheduled grant info			RBS-2697
– Uplink transport channel type						DCH			RBS-2698
– UL Transport channel identity						5			RBS-2699
– TFS									RBS-2700
– CHOICE Transport channel type						Dedicated transport channels			RBS-2701
– Dynamic Transport format information									RBS-2702
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2703
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2704
– Transmission Time Interval						Not Present			RBS-2705
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-2706
– CHOICE Logical channel list						All			RBS-2707
– Semi-static Transport Format information									RBS-2708
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2709
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2710
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2711
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2712
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2713
DL Transport channel information common for all transport channel			A1, A2, A7, A8						RBS-2714
– SCCPCH TFCS						Not Present			RBS-2715
– CHOICE mode						FDD			RBS-2716
– CHOICE DL parameters						SameasUL			RBS-2717
DL Transport channel information common for all transport channel			A3, A4, A5, A6, A11						RBS-2718
			A10					Rel-5	RBS-2719
			, A12, A13, A15					Rel-6	RBS-2720
			, A17, A18, A17a, A17d, A17e, A17f, A19, A19a,					Rel-7	RBS-2721
			, A25a, A25b, A26, A28					Rel-8	RBS-2722
			, A31, A32 , A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-2723
– SCCPCH TFCS						Not Present			RBS-2724
– CHOICE mode						FDD			RBS-2725
– CHOICE DL parameters						Explicit			RBS-2726
– DL DCH TFCS									RBS-2727
– CHOICE TFCI Signalling						Normal			RBS-2728
– TFCI Field 1 Information									RBS-2729
– CHOICE TFCS representation						Complete reconfiguration			RBS-2730
– TFCS complete reconfigure									RBS-2731
– CHOICE CTFC Size						Number of bits used must be enough to cover all combinations of CTFC from clause 6.10.2.4 Parameter Set.			RBS-2732
– CTFC information						This IE is repeated for TFC numbers and reference to clause 6.10.2.4			RBS-2733
– CTFC						Reference to clause 6.10.2.4 Parameter Set			RBS-2734
– Power offset information						Not Present			RBS-2735
DL Transport channel information common for all transport channel			A9					Rel-5	RBS-2736
– SCCPCH TFCS						Not Present			RBS-2737
– CHOICE mode						FDD			RBS-2738
– CHOICE DL parameters						Explicit			RBS-2739
– DL DCH TFCS									RBS-2740
– CHOICE TFCI Signalling						Normal			RBS-2741
– TFCI Field 1 Information									RBS-2742
– CHOICE TFCS representation						Complete reconfiguration			RBS-2743
– TFCS complete reconfigure									RBS-2744
– CHOICE CTFC Size						ctfc2bit			RBS-2745
– CTFC information									RBS-2746
– CTFC						0 ((DL DCH RAB, DCCH)=(TF0, TF0))			RBS-2747
– Power offset information						Not Present			RBS-2748
– CTFC						1 ((DL DCH RAB, DCCH)=(TF0, TF1))			RBS-2749
– Power offset information						Not Present			RBS-2750
DL Transport channel information common for all transport channel			A14, A16			Not Present		Rel-6	RBS-2751
			, A17b, A17c, A19b, A20, A21, A22, A24					Rel-7	RBS-2752
			, A23, A28a					Rel-7 Rel-8	RBS-2753
			, A25, A27, A27a, A29, A30, A25c					Rel-8 Rel-9	RBS-2754
Deleted DL TrCH information			A1, A2, A3, A4, A5, A6, A7, A8			Not Present			RBS-2755
			, A9, A10					Rel-5	RBS-2756
			, A12, A13					Rel-6	RBS-2757
			, A17, A18, A17a, A17d, A17e, A17f, A19, A19a, A20, A21, A24					Rel-7	RBS-2758
			, A25a, A25b, A26, A28, A29					Rel-8	RBS-2759
			, A35 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-2760
Deleted DL TrCH information			A14, A16					Rel-6	RBS-2761
			A17b, A17c, A19b, A22					Rel-7	RBS-2762
			A25, A27, A27a, A25c, A28a						RBS-2763
			, A31, A32					Rel-9	RBS-2764
			, A33, A34, A36, A37					Rel-10	RBS-2765
– Downlink transport channel type						DCH			RBS-2766
– DL Transport channel identity						10			RBS-2767
Deleted DL TrCH information – Downlink transport channel type – DL HS-DSCH MAC-d flow identity			A30			mac_ehs 1		Rel-8	RBS-2767a
Added or Reconfigured DL TrCH information			A1			1 DCH added, 1 DCH reconfigured			RBS-2768
– Downlink transport channel type						DCH			RBS-2769
– DL Transport channel identity						6			RBS-2770
– CHOICE DL parameters						Same as UL			RBS-2771
– Uplink transport channel type						DCH			RBS-2772
– UL TrCH identity						1			RBS-2773
– DCH quality target									RBS-2774
– BLER Quality value						-20 (-2.0)			RBS-2775
– Downlink transport channel type						DCH			RBS-2776
– DL Transport channel identity						10			RBS-2777
– CHOICE DL parameters						Same as UL			RBS-2778
– Uplink transport channel type						DCH			RBS-2779
– UL TrCH identity						5			RBS-2780
– DCH quality target									RBS-2781
– BLER Quality value						-20 (-2.0)			RBS-2782
Added or Reconfigured DL TrCH information			A3, A4, A5, A6, A7			2 TrCHs(DCH for DCCH and DCH for DTCH)			RBS-2783
– Downlink transport channel type						DCH			RBS-2784
– DL Transport channel identity						10			RBS-2785
– CHOICE DL parameters						Same as UL			RBS-2786
– Uplink transport channel type						DCH			RBS-2787
– UL TrCH identity						5			RBS-2788
– DCH quality target									RBS-2789
– BLER Quality value						-20 (-2.0)			RBS-2790
– Downlink transport channel type						DCH			RBS-2791
– DL Transport channel identity						6			RBS-2792
– CHOICE DL parameters						Explicit Except for RAB with the symmetric DL and UL rate: Same as UL			RBS-2793
– TFS									RBS-2794
– CHOICE Transport channel type						Dedicated transport channel			RBS-2795
– Dynamic transport format information									RBS-2796
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2797
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2798
– Transmission Time Interval						Not Present			RBS-2799
– Number of Transport blocks						Reference to clause 6.10 Parameter Set only including TF0			RBS-2800
– CHOICE Logical channel list						All			RBS-2801
– Semi-static Transport Format information									RBS-2802
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2803
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2804
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2805
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2806
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2807
– DCH quality target									RBS-2808
– BLER Quality value						-20 (-2.0)			RBS-2809
Added or Reconfigured DL TrCH information			A2, A8			4 TrCHs(DCH for DCCH and 3DCHs for DTCH)			RBS-2810
– Downlink transport channel type						DCH			RBS-2811
– DL Transport channel identity						10			RBS-2812
– CHOICE DL parameters						Same as UL			RBS-2813
– Uplink transport channel type						DCH			RBS-2814
– UL TrCH identity						5			RBS-2815
– DCH quality target									RBS-2816
– BLER Quality value						-20 (-2.0)			RBS-2817
– Downlink transport channel type						DCH			RBS-2818
– DL Transport channel identity						6			RBS-2819
– CHOICE DL parameters						Explicit			RBS-2820
– TFS									RBS-2821
– CHOICE Transport channel type						Dedicated transport channel			RBS-2822
– Dynamic transport format information									RBS-2823
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2824
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2825
– Dynamic transport format information									RBS-2826
– Transmission Time Interval						Not Present			RBS-2827
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-2828
– CHOICE Logical channel list						All			RBS-2829
– Semi-static Transport Format information									RBS-2830
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2831
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2832
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2833
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2834
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2835
– DCH quality target									RBS-2836
– BLER Quality value						Not Present			RBS-2837
– Downlink transport channel type						DCH			RBS-2838
– DL Transport channel identity						7			RBS-2839
– CHOICE DL parameters						Explicit			RBS-2840
– TFS									RBS-2841
– CHOICE Transport channel type						Dedicated transport channel			RBS-2842
– Dynamic transport format information									RBS-2843
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2844
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2845
– Dynamic transport format information									RBS-2846
– Transmission Time Interval						Not Present			RBS-2847
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-2848
– CHOICE Logical channel list						All			RBS-2849
– Semi-static Transport Format information									RBS-2850
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2851
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2852
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2853
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2854
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2855
– DCH quality target									RBS-2856
– BLER Quality value						Not Present			RBS-2857
– Downlink transport channel type						DCH			RBS-2858
– DL Transport channel identity						8			RBS-2859
– CHOICE DL parameters						Explicit			RBS-2860
– TFS									RBS-2861
– CHOICE Transport channel type						Dedicated transport channel			RBS-2862
– Dynamic transport format information									RBS-2863
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2864
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2865
– Dynamic transport format information									RBS-2866
– Transmission Time Interval						Not Present			RBS-2867
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-2868
– CHOICE Logical channel list						All			RBS-2869
– Semi-static Transport Format information									RBS-2870
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2871
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2872
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2873
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2874
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2875
– DCH quality target									RBS-2876
– BLER Quality value						Not Present			RBS-2877
Added or Reconfigured DL TrCH information			A9			3 TrCHs (DCH for DCCH and DCH plus HS-DSCH for DTCH)		Rel-5	RBS-2878
Added or Reconfigured DL TrCH information			A12			3 TrCHs (DCH for DCCH and DCH plus HS-DSCH for DTCH)		Rel-6	RBS-2879
			A19					Rel-7	RBS-2880
– Downlink transport channel type						DCH			RBS-2881
– DL Transport channel identity						10			RBS-2882
– CHOICE DL parameters						Same as UL			RBS-2883
– Uplink transport channel type						DCH			RBS-2884
– UL TrCH identity						5			RBS-2885
– DCH quality target									RBS-2886
– BLER Quality value						-20 (-2.0)			RBS-2887
– Downlink transport channel type						DCH			RBS-2888
– DL Transport channel identity						6			RBS-2889
– CHOICE DL parameters						Explicit			RBS-2890
– TFS									RBS-2891
– CHOICE Transport channel type						Dedicated transport channel			RBS-2892
– Dynamic transport format information									RBS-2893
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2894
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2895
– Dynamic transport format information									RBS-2896
– Transmission Time Interval						Not Present			RBS-2897
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-2898
– CHOICE Logical channel list						All			RBS-2899
– Semi-static Transport Format information									RBS-2900
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2901
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2902
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2903
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2904
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2905
– DCH quality target									RBS-2906
– BLER Quality value						-20 (-2.0)			RBS-2907
– Downlink transport channel type						HS-DSCH			RBS-2908
– DL Transport channel identity						Not Present			RBS-2909
– CHOICE DL parameters						HS-DSCH			RBS-2910
– HARQ Info									RBS-2911
– Number of Processes						Reference to clause 6.10.2.4.5 Parameter Set			RBS-2912
– CHOICE Memory Partitioning						Implicit			RBS-2913
– Added or reconfigured MAC-d flow									RBS-2914
– MAC-hs queue to add or reconfigure list						(one queue)			RBS-2915
– MAC-hs queue Id						0			RBS-2916
– MAC-d Flow Identity						0			RBS-2917
– T1						50			RBS-2918
– MAC-hs window size						16			RBS-2919
– MAC-d PDU size Info									RBS-2920
– MAC-d PDU size						336			RBS-2921
– MAC-d PDU size index						0			RBS-2922
– MAC-hs queue to delete list						Not present			RBS-2923
– DCH quality target						Not present			RBS-2924
Added or Reconfigured DL TrCH information			A10			2 TrCHs (DCH for DCCH and HS-DSCH for DTCH)		Rel-5	RBS-2925
– Downlink transport channel type						DCH			RBS-2926
– DL Transport channel identity						10			RBS-2927
– CHOICE DL parameters						Same as UL			RBS-2928
– Uplink transport channel type						DCH			RBS-2929
– UL TrCH identity						5			RBS-2930
– DCH quality target									RBS-2931
– BLER Quality value						-20 (-2.0)			RBS-2932
– Downlink transport channel type						HS-DSCH			RBS-2933
– DL Transport channel identity						Not Present			RBS-2934
– CHOICE DL parameters						HS-DSCH			RBS-2935
– HARQ Info									RBS-2936
– Number of Processes						Reference to clause 6.10.2.4.5 Parameter Set			RBS-2937
– CHOICE Memory Partitioning						Implicit			RBS-2938
– Added or reconfigured MAC-d flow									RBS-2939
– MAC-hs queue to add or reconfigure list						(one queue)			RBS-2940
– MAC-hs queue Id						0			RBS-2941
– MAC-d Flow Identity						0			RBS-2942
– T1						50			RBS-2943
– MAC-hs window size						16			RBS-2944
– MAC-d PDU size Info									RBS-2945
– MAC-d PDU size						336			RBS-2946
– MAC-d PDU size index						0			RBS-2947
– MAC-hs queue to delete list						Not present			RBS-2948
– DCH quality target						Not present			RBS-2949
Added or Reconfigured DL TrCH information			A11			1 DCH for DTCH			RBS-2950
– Downlink transport channel type						DCH			RBS-2951
– DL Transport channel identity						9			RBS-2952
– CHOICE DL parameters						Explicit			RBS-2953
– TFS									RBS-2954
– CHOICE Transport channel type						Dedicated transport channel			RBS-2955
– Dynamic transport format information									RBS-2956
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2957
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2958
– Dynamic transport format information									RBS-2959
– Transmission Time Interval						Not Present			RBS-2960
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-2961
– CHOICE Logical channel list						All			RBS-2962
– Semi-static Transport Format information									RBS-2963
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2964
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2965
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2966
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2967
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2968
– DCH quality target									RBS-2969
– BLER Quality value						-20 (-2.0)			RBS-2970
Added or Reconfigured DL TrCH information			A13			2 TrCHs (DCH for DCCH and HS-DSCH for DTCH)		Rel-6	RBS-2971
– Downlink transport channel type						DCH			RBS-2972
– DL Transport channel identity						10			RBS-2973
– CHOICE DL parameters						Explicit			RBS-2974
– TFS									RBS-2975
– CHOICE Transport channel type						Dedicated transport channels			RBS-2976
– Dynamic Transport format information									RBS-2977
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-2978
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-2979
– Transmission Time Interval						Not Present			RBS-2980
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-2981
– CHOICE Logical channel list						All			RBS-2982
– Semi-static Transport Format information									RBS-2983
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-2984
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-2985
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-2986
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-2987
– CRC size						Reference to clause 6.10 Parameter Set			RBS-2988
– DCH quality target									RBS-2989
– BLER Quality value						-20 (-2.0)			RBS-2990
– Downlink transport channel type						HS-DSCH			RBS-2991
– DL Transport channel identity						Not Present			RBS-2992
– CHOICE DL parameters						HS-DSCH			RBS-2993
– HARQ Info									RBS-2994
– Number of Processes						Reference to clause 6.10.2.4.5 Parameter Set			RBS-2995
– CHOICE Memory Partitioning						Implicit			RBS-2996
– Added or reconfigured MAC-d flow									RBS-2997
– MAC-hs queue to add or reconfigure list						(one queue)			RBS-2998
– MAC-hs queue Id						0			RBS-2999
– MAC-d Flow Identity						0			RBS-3000
– T1						50			RBS-3001
– MAC-hs window size						16			RBS-3002
– MAC-d PDU size Info									RBS-3003
– MAC-d PDU size						336			RBS-3004
– MAC-d PDU size index						0			RBS-3005
– MAC-hs queue to delete list						Not present			RBS-3006
– DCH quality target						Not present			RBS-3007
Added or Reconfigured DL TrCH information – Downlink transport channel type – DL Transport channel identity – CHOICE DL parameters – TFS – CHOICE Transport channel type – Dynamic Transport format information – RLC Size – Number of TBs and TTI List – Transmission Time Interval – Number of Transport blocks			A19a			2 TrCHs (DCH for DCCH and HS-DSCH for DTCH)		Rel-7	RBS-3008 RBS-3009 RBS-3010 RBS-3011 RBS-3012 RBS-3013 RBS-3014 RBS-3015 RBS-3016 RBS-3017 RBS-3018 RBS-3019 RBS-3020 RBS-3021 RBS-3022 RBS-3023 RBS-3024 RBS-3025 RBS-3026 RBS-3027 RBS-3028 RBS-3029 RBS-3030 RBS-3031 RBS-3032 RBS-3033 RBS-3034 RBS-3035 RBS-3036 RBS-3037 RBS-3038 RBS-3039 RBS-3040 RBS-3041 RBS-3042 RBS-3043 RBS-3044
						DCH
						10
						Explicit

						Dedicated transport channels

						Reference to clause 6.10 Parameter Set
						(This IE is repeated for TFI number.)
						Not Present
						Reference to clause 6.10 Parameter Set
– CHOICE Logical channel list						All
– Semi-static Transport Format information
– Transmission time interval						Reference to clause 6.10 Parameter Set
– Type of channel coding						Reference to clause 6.10 Parameter Set
– Coding Rate						Reference to clause 6.10 Parameter Set
– Rate matching attribute						Reference to clause 6.10 Parameter Set
– CRC size						Reference to clause 6.10 Parameter Set
– DCH quality target
– BLER Quality value						-20 (-2.0)
– Downlink transport channel type						HS-DSCH
– DL Transport channel identity						Not Present
– CHOICE DL parameters						HS-DSCH
– HARQ Info
– Number of Processes						Reference to clause 6.10.2.4.5 Parameter Set
– CHOICE Memory Partitioning						Implicit
– Added or reconfigured MAC-d flow
– MAC-hs queue to add or reconfigure list						(one queue)
– MAC-hs queue Id						0
– MAC-d Flow Identity						0
– T1 – MAC-hs window size – MAC-d PDU size Info – MAC-d PDU size – MAC-d PDU size index – MAC-hs queue to delete list – DCH quality target						50
						16

						336
						0
						Not present
						Not present
Added or Reconfigured DL TrCH information			A14			1 TrCH (HS-DSCH for DTCH and DCCH)		Rel-6	RBS-3045
			, A20					Rel-7	RBS-3046
			, A31, A32					Rel-9	RBS-3047
– Downlink transport channel type						HS-DSCH			RBS-3048
– DL Transport channel identity						Not Present			RBS-3049
– CHOICE DL parameters						HS-DSCH			RBS-3050
– HARQ Info									RBS-3051
– Number of Processes						Reference to clause 6.10.2.4.5 Parameter Set			RBS-3052
– CHOICE Memory Partitioning						Implicit			RBS-3053
– Added or reconfigured MAC-d flow									RBS-3054
– MAC-hs queue to add or reconfigure list						(two queues)			RBS-3055
– MAC-hs queue Id						0 (for DTCH)			RBS-3056
– MAC-d Flow Identity						0			RBS-3057
– T1						50			RBS-3058
– MAC-hs window size						16			RBS-3059
– MAC-d PDU size Info									RBS-3060
– MAC-d PDU size						336			RBS-3061
– MAC-d PDU size index						0			RBS-3062
– MAC-hs queue Id						1 (for DCCH)			RBS-3063
– MAC-d Flow Identity						1			RBS-3064
– T1						50			RBS-3065
– MAC-hs window size						16			RBS-3066
– MAC-d PDU size Info									RBS-3067
– MAC-d PDU size						148			RBS-3068
– MAC-d PDU size index						0			RBS-3069
– MAC-hs queue to delete list						Not present			RBS-3070
– DCH quality target						Not present			RBS-3071
Added or Reconfigured DL TrCH information			A15			2 TrCHs (DCH for DCCH and HS-DSCH for DTCH)		Rel-6	RBS-3072
– Downlink transport channel type						DCH			RBS-3073
– DL Transport channel identity						10			RBS-3074
– CHOICE DL parameters						Explicit			RBS-3075
– TFS									RBS-3076
– CHOICE Transport channel type						Dedicated transport channels			RBS-3077
– Dynamic Transport format information									RBS-3078
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-3079
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-3080
– Transmission Time Interval						Not Present			RBS-3081
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-3082
– CHOICE Logical channel list						All			RBS-3083
– Semi-static Transport Format information									RBS-3084
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-3085
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-3086
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-3087
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-3088
– CRC size						Reference to clause 6.10 Parameter Set			RBS-3089
– DCH quality target									RBS-3090
– BLER Quality value						-20 (-2.0)			RBS-3091
– Downlink transport channel type						HS-DSCH			RBS-3092
– DL Transport channel identity						Not Present			RBS-3093
– CHOICE DL parameters						HS-DSCH			RBS-3094
– HARQ Info									RBS-3095
– Number of Processes						Reference to clause 6.10.2.4.5 Parameter Set			RBS-3096
– CHOICE Memory Partitioning						Implicit			RBS-3097
– Added or reconfigured MAC-d flow									RBS-3098
– MAC-hs queue to add or reconfigure list						(two queues)			RBS-3099
– MAC-hs queue Id						0 (for first DTCH)			RBS-3100
– MAC-d Flow Identity						0			RBS-3101
– T1						50			RBS-3102
– MAC-hs window size						16			RBS-3103
– MAC-d PDU size Info									RBS-3104
– MAC-d PDU size						336			RBS-3105
– MAC-d PDU size index						0			RBS-3106
– MAC-hs queue Id						2 (for second DTCH)			RBS-3107
– MAC-d Flow Identity						2			RBS-3108
– T1						50			RBS-3109
– MAC-hs window size						16			RBS-3110
– MAC-d PDU size Info									RBS-3111
– MAC-d PDU size						336			RBS-3112
– MAC-d PDU size index						0			RBS-3113
– MAC-hs queue to delete list						Not present			RBS-3114
– DCH quality target						Not present			RBS-3115
Added or Reconfigured DL TrCH information			A16			1 TrCH (HS-DSCH for 2 DTCHs and DCCH)		Rel-6	RBS-3116
			, A19b, A21					Rel-7	RBS-3117
– Downlink transport channel type						HS-DSCH			RBS-3118
– DL Transport channel identity						Not Present			RBS-3119
– CHOICE DL parameters						HS-DSCH			RBS-3120
– HARQ Info									RBS-3121
– Number of Processes						Reference to clause 6.10.2.4.5 Parameter Set			RBS-3122
– CHOICE Memory Partitioning						Implicit			RBS-3123
– Added or reconfigured MAC-d flow									RBS-3124
– MAC-hs queue to add or reconfigure list						(three queues)			RBS-3125
– MAC-hs queue Id						0 (for first DTCH)			RBS-3126
– MAC-d Flow Identity						0			RBS-3127
– T1						50			RBS-3128
– MAC-hs window size						16			RBS-3129
– MAC-d PDU size Info									RBS-3130
– MAC-d PDU size						336			RBS-3131
– MAC-d PDU size index						0			RBS-3132
– MAC-hs queue Id						1 (for DCCH)			RBS-3133
– MAC-d Flow Identity						1			RBS-3134
– T1						50			RBS-3135
– MAC-hs window size						16			RBS-3136
– MAC-d PDU size Info									RBS-3137
– MAC-d PDU size						148			RBS-3138
– MAC-d PDU size index						0			RBS-3139
– MAC-hs queue Id						3 (for second DTCH)			RBS-3140
– MAC-d Flow Identity						3			RBS-3141
– T1						50			RBS-3142
– MAC-hs window size						16			RBS-3143
– MAC-d PDU size Info									RBS-3144
– MAC-d PDU size						112			RBS-3145
– MAC-d PDU size index						0			RBS-3146
– MAC-d PDU size						144			RBS-3147
– MAC-d PDU size index						1			RBS-3148
– MAC-d PDU size						160			RBS-3149
– MAC-d PDU size index						2			RBS-3150
– MAC-d PDU size						176			RBS-3151
– MAC-d PDU size index						3			RBS-3152
– MAC-d PDU size						192			RBS-3153
– MAC-d PDU size index						4			RBS-3154
– MAC-d PDU size						224			RBS-3155
– MAC-d PDU size index						5			RBS-3156
– MAC-d PDU size						296			RBS-3157
– MAC-d PDU size index						6			RBS-3158
– MAC-d PDU size						344			RBS-3159
– MAC-d PDU size index						7			RBS-3160
– MAC-hs queue to delete list						Not present			RBS-3161
– DCH quality target						Not present			RBS-3162
Added or Reconfigured DL TrCH information			A17, A17a, A18			2 TrCHs (DCH for DCCH and HS-DSCH for DTCH)		Rel-7	RBS-3163
			, A25a					Rel-8	RBS-3164
– Downlink transport channel type						DCH			RBS-3165
– DL Transport channel identity						10			RBS-3166
– CHOICE DL parameters						Same as UL			RBS-3167
– Uplink transport channel type						DCH			RBS-3168
– UL TrCH identity						5			RBS-3169
– DCH quality target									RBS-3170
– BLER Quality value						-20 (-2.0)			RBS-3171
– Downlink transport channel type						HS-DSCH			RBS-3172
– DL Transport channel identity						Not Present			RBS-3173
– CHOICE DL parameters						HS-DSCH			RBS-3174
– HARQ Info									RBS-3175
– Number of Processes						Reference to clause 6.10.2.4.5 Parameter Set			RBS-3176
– CHOICE Memory Partitioning						Implicit			RBS-3177
– CHOICE DL MAC header type						MAC-ehs			RBS-3178
– Added or reconfigured MAC-ehs reordering queue									RBS-3179
– MAC-ehs queue to add or reconfigure list						(one queue)			RBS-3180
– MAC-ehs queue Id						0			RBS-3181
– T1						50			RBS-3182
– MAC-ehs window size						16			RBS-3183
– MAC-ehs queue to delete list						Not present			RBS-3184
– DCH quality target						Not present			RBS-3185
Added or Reconfigured DL TrCH information			A17b, A17c, A28a A25c , A33, A34, A36, A37			1 TrCH (HS-DSCH for DTCH and DCCH)		Rel-7 Rel-9 Rel-10	RBS-3186
– Downlink transport channel type						HS-DSCH			RBS-3187
– DL Transport channel identity						Not Present			RBS-3188
– CHOICE DL parameters						HS-DSCH			RBS-3189
– HARQ Info									RBS-3190
– Number of Processes						Reference to clause 6.10.2.4.5 Parameter Set			RBS-3191
– CHOICE Memory Partitioning						Implicit			RBS-3192
– CHOICE DL MAC header type						MAC-ehs			RBS-3193
– Added or reconfigured MAC-ehs reordering queue									RBS-3194
– MAC-hs queue to add or reconfigure list						(two queues)			RBS-3195
– MAC-ehs queue Id						0 (for DTCH)			RBS-3196
– T1						50			RBS-3197
– MAC-ehs window size						16			RBS-3198
– MAC-ehs queue Id						1 (for DCCH)			RBS-3199
– T1						50			RBS-3200
– MAC-hs window size						16			RBS-3201
– MAC-ehs queue to delete list						Not present			RBS-3202
– DCH quality target						Not present			RBS-3203
Added or Reconfigured DL TrCH information			A17d, A17e, A17f			2 TrCHs (DCH for DCCH and HS-DSCH for DTCH)		Rel-7	RBS-3204
			, A25b					Rel-8	RBS-3205
– Downlink transport channel type						DCH			RBS-3206
– DL Transport channel identity						10			RBS-3207
– CHOICE DL parameters						Explicit			RBS-3208
– TFS									RBS-3209
– CHOICE Transport channel type						Dedicated transport channels			RBS-3210
– Dynamic Transport format information									RBS-3211
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-3212
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-3213
– Transmission Time Interval						Not Present			RBS-3214
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-3215
– CHOICE Logical channel list						All			RBS-3216
– Semi-static Transport Format information									RBS-3217
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-3218
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-3219
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-3220
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-3221
– CRC size						Reference to clause 6.10 Parameter Set			RBS-3222
– DCH quality target									RBS-3223
– BLER Quality value						-20 (-2.0)			RBS-3224
– Downlink transport channel type						HS-DSCH			RBS-3225
– DL Transport channel identity						Not Present			RBS-3226
– CHOICE DL parameters						HS-DSCH			RBS-3227
– HARQ Info									RBS-3228
– Number of Processes						Reference to clause 6.10.2.4.5 Parameter Set			RBS-3229
– CHOICE Memory Partitioning						Implicit			RBS-3230
– CHOICE DL MAC header type						MAC-ehs			RBS-3231
– Added or reconfigured MAC-ehs reordering queue									RBS-3232
– MAC-ehs queue to add or reconfigure list						(one queue)			RBS-3233
– MAC-ehs queue Id						0			RBS-3234
– T1						50			RBS-3235
– MAC-ehs window size						16			RBS-3236
– MAC-ehs queue to delete list						Not present			RBS-3237
– DCH quality target						Not present			RBS-3238
Added or Reconfigured DL TrCH information			A22			1 TrCH (HS-DSCH for 2 DTCHs and DCCH)		Rel-7	RBS-3239
– Downlink transport channel type						HS-DSCH			RBS-3240
– DL Transport channel identity						Not Present			RBS-3241
– CHOICE DL parameters						HS-DSCH			RBS-3242
– HARQ Info									RBS-3243
– Number of Processes						Reference to clause 6.10.2.4.5 Parameter Set			RBS-3244
– CHOICE Memory Partitioning						Implicit			RBS-3245
– CHOICE DL MAC header type						MAC-ehs			RBS-3246
– Added or reconfigured MAC-ehs reordering queue									RBS-3247
– MAC-ehs queue to add or reconfigure list						(three queues)			RBS-3248
– MAC-ehs queue Id						0 (for first DTCH)			RBS-3249
– T1						50			RBS-3250
– MAC-ehs window size						16			RBS-3251
– MAC-ehs queue Id						1 (for DCCH)			RBS-3252
– T1						50			RBS-3253
– MAC-ehs window size						16			RBS-3254
– MAC-ehs queue Id						3 (for second DTCH)			RBS-3255
– T1						50			RBS-3256
– MAC-ehs window size						16			RBS-3257
– MAC-ehs queue to delete list						Not present			RBS-3258
– DCH quality target						Not present			RBS-3259
Added or Reconfigured DL TrCH information			A23			1 TrCH (HS-DSCH for DTCHs and DCCH)		Rel-7 Rel-8	RBS-3260
– Downlink transport channel type						HS-DSCH			RBS-3261
– DL Transport channel identity						Not Present			RBS-3262
– CHOICE DL parameters						HS-DSCH			RBS-3263
– HARQ Info									RBS-3264
– Number of Processes						Reference to clause 6.10 Parameter Set			RBS-3265
– CHOICE Memory Partitioning						Implicit			RBS-3266
– CHOICE DL MAC header type						MAC-ehs			RBS-3267
– Added or reconfigured MAC-ehs reordering queue									RBS-3268
– MAC-ehs queue to add or reconfigure list						(two queues)			RBS-3269
– MAC-ehs queue Id						0 (for DTCH)			RBS-3270
– T1						50			RBS-3271
– MAC-ehs window size						16			RBS-3272
– MAC-ehs queue Id						1 (for DCCH)			RBS-3273
– T1						50			RBS-3274
– MAC-ehs window size						16			RBS-3275
– MAC-ehs queue to delete list						Not present			RBS-3276
– DCH quality target						Not present			RBS-3277
Added or Reconfigured DL TrCH information			A25			1 TrCH (HS-DSCH for DTCH and DCCH)		Rel-8	RBS-3278
– Downlink transport channel type						HS-DSCH			RBS-3279
– DL Transport channel identity						Not Present			RBS-3280
– CHOICE DL parameters						HS-DSCH			RBS-3281
– HARQ Info									RBS-3282
– Number of Processes						Reference to clause 6.10.2.4.5 Parameter Set			RBS-3283
– CHOICE Memory Partitioning						Implicit			RBS-3284
– CHOICE DL MAC header type						MAC-ehs			RBS-3285
– Added or reconfigured MAC-ehs reordering queue									RBS-3286
– MAC-ehs queue to add or reconfigure list						(two queues)			RBS-3287
– MAC-ehs queue Id						0 (for DTCH)			RBS-3288
– T1						50			RBS-3289
– MAC-ehs window size						16			RBS-3290
– MAC-ehs queue Id						1 (for DCCH)			RBS-3291
– T1						50			RBS-3292
– MAC-ehs window size						16			RBS-3293
– MAC-ehs queue to delete list						Not present			RBS-3294
– DCH quality target						Not present			RBS-3295
Added or Reconfigured DL TrCH information			A28			2 TrCHs (DCH for DCCH and HS-DSCH for DTCH)		Rel-8	RBS-3296
– Downlink transport channel type						DCH			RBS-3297
– DL Transport channel identity						10			RBS-3298
– CHOICE DL parameters						Same as UL			RBS-3299
– Uplink transport channel type						DCH			RBS-3300
– UL TrCH identity						5			RBS-3301
– DCH quality target									RBS-3302
– BLER Quality value						-20 (-2.0)			RBS-3303
– Downlink transport channel type						HS-DSCH			RBS-3304
– DL Transport channel identity						Not Present			RBS-3305
– CHOICE DL parameters						HS-DSCH			RBS-3306
– HARQ Info									RBS-3307
– Number of Processes						Reference to clause 6.10.2.4.5 Parameter Set			RBS-3308
– CHOICE Memory Partitioning						Implicit			RBS-3309
– CHOICE DL MAC header type						MAC-ehs			RBS-3310
– Added or reconfigured MAC-ehs reordering queue									RBS-3311
– MAC-ehs queue to add or reconfigure list						(one queue)			RBS-3312
– MAC-ehs queue Id						0			RBS-3313
– T1						50			RBS-3314
– MAC-ehs window size						32			RBS-3315
– MAC-ehs queue to delete list						Not present			RBS-3316
– DCH quality target						Not present			RBS-3317
Added or Reconfigured DL TrCH information list			A24, A29			1 TrCH (HS-DSCH for DTCH)			RBS-3318
– Downlink transport channel type						HS-DSCH			RBS-3319
– DL Transport channel identity						Not Present			RBS-3320
– CHOICE DL parameters						HS-DSCH			RBS-3321
– HARQ Info									RBS-3322
– Number of Processes						Reference to clause 6.10 Parameter Set			RBS-3323
– CHOICE Memory Partitioning						Implicit			RBS-3324
– CHOICE DL MAC header type						MAC-ehs			RBS-3325
– Added or reconfigured MAC-ehs reordering queue									RBS-3326
– MAC-ehs queue to add or reconfigure list						(one queue)			RBS-3327
– MAC-ehs queue Id						2 (for DTCH)			RBS-3328
– T1						50			RBS-3329
– MAC-ehs window size						16			RBS-3330
– DCH quality target						Not present			RBS-3331
Added or Reconfigured DL TrCH information			A26			2 TrCHs (DCH for DCCH and HS-DSCH for 3 DTCHs)		Rel-8	RBS-3332
– Downlink transport channel type						DCH			RBS-3333
– DL Transport channel identity						10			RBS-3334
– CHOICE DL parameters						Explicit			RBS-3335
– TFS									RBS-3336
– CHOICE Transport channel type						Dedicated transport channels			RBS-3337
– Dynamic Transport format information									RBS-3338
– RLC Size						Reference to clause 6.10 Parameter Set			RBS-3339
– Number of TBs and TTI List						(This IE is repeated for TFI number.)			RBS-3340
– Transmission Time Interval						Not Present			RBS-3341
– Number of Transport blocks						Reference to clause 6.10 Parameter Set			RBS-3342
– CHOICE Logical channel list						All			RBS-3343
– Semi-static Transport Format information									RBS-3344
– Transmission time interval						Reference to clause 6.10 Parameter Set			RBS-3345
– Type of channel coding						Reference to clause 6.10 Parameter Set			RBS-3346
– Coding Rate						Reference to clause 6.10 Parameter Set			RBS-3347
– Rate matching attribute						Reference to clause 6.10 Parameter Set			RBS-3348
– CRC size						Reference to clause 6.10 Parameter Set			RBS-3349
– DCH quality target									RBS-3350
– BLER Quality value						-20 (-2.0)			RBS-3351
– Downlink transport channel type						HS-DSCH			RBS-3352
– DL Transport channel identity						Not Present			RBS-3353
– CHOICE DL parameters						HS-DSCH			RBS-3354
– HARQ Info									RBS-3355
– Number of Processes						Reference to clause 6.10.2.4.5 Parameter Set			RBS-3356
– CHOICE Memory Partitioning						Implicit			RBS-3357
– CHOICE DL MAC header type						MAC-ehs			RBS-3358
– Added or reconfigured MAC-ehs reordering queue									RBS-3359
– MAC-ehs queue to add or reconfigure list						(three queues)			RBS-3360
									RBS-3361
– MAC-ehs queue Id						2 (for first DTCH)			RBS-3362
– T1						50			RBS-3363
– MAC-ehs window size						16			RBS-3364
– MAC-ehs queue Id						3 (for second DTCH)			RBS-3365
– T1						50			RBS-3366
– MAC-ehs window size						16			RBS-3367
– MAC-ehs queue Id						4 (for third DTCH)			RBS-3368
– T1						50			RBS-3369
– MAC-ehs window size						16			RBS-3370
– DCH quality target						Not present			RBS-3371
Added or Reconfigured DL TrCH information			A27, A27a			1 TrCH (HS-DSCH for 2 DTCHs and DCCH)		Rel-8	RBS-3372
– Downlink transport channel type						HS-DSCH			RBS-3373
– DL Transport channel identity						Not Present			RBS-3374
– CHOICE DL parameters						HS-DSCH			RBS-3375
– HARQ Info									RBS-3376
– Number of Processes						Reference to clause 6.10.2.4.5 Parameter Set			RBS-3377
– CHOICE Memory Partitioning						Implicit			RBS-3378
– CHOICE DL MAC header type						MAC-ehs			RBS-3379
– Added or reconfigured MAC-ehs reordering queue									RBS-3380
– MAC-ehs queue to add or reconfigure list						(two queues)			RBS-3381
– MAC-ehs queue Id						0 (for first DTCH)			RBS-3382
– T1						50			RBS-3383
– MAC-ehs window size						16			RBS-3384
– MAC-ehs queue Id						1 (for DCCH)			RBS-3385
– T1						50			RBS-3386
– MAC-ehs window size						16			RBS-3387
– DCH quality target						Not present			RBS-3388
Added or Reconfigured DL TrCH information			A30			1 TrCH (HS-DSCH for DTCH and DCCH)		Rel-8	RBS-3389
– Downlink transport channel type						HS-DSCH			RBS-3390
– DL Transport channel identity						Not Present			RBS-3391
– CHOICE DL parameters						HS-DSCH			RBS-3392
– HARQ Info									RBS-3393
– Number of Processes						Reference to clause 6.10.2.4.5 Parameter Set			RBS-3394
– CHOICE Memory Partitioning						Implicit			RBS-3395
– CHOICE DL MAC header type						MAC-ehs			RBS-3396
– Added or reconfigured MAC-ehs reordering queue									RBS-3397
– MAC-hs queue to add or reconfigure list						(two queues)			RBS-3398
– MAC-ehs queue Id						2 (for DTCH)			RBS-3399
– T1						50			RBS-3400
– MAC-ehs window size						16			RBS-3401
– MAC-ehs queue Id						3 (for DCCH)			RBS-3402
– T1						50			RBS-3403
– MAC-hs window size						16			RBS-3404
– MAC-ehs queue to delete list						Not present			RBS-3405
– DCH quality target						Not present			RBS-3406
Added or Reconfigured DL TrCH information list			A35 A38, A39, A40, A41, A42, A43, A44, A45			2 TrCh (DCH for DCCH and HS-DSCH for DTCH)		Rel-10 Rel-11	RBS-3407
– Downlink transport channel type						DCH			RBS-3408
– DL Transport channel identity						10			RBS-3409
– CHOICE DL parameters						Same as UL			RBS-3410
– Uplink transport channel type						DCH			RBS-3411
– UL TrCH identity						5			RBS-3412
			A33, A34, A35, A36, A37					Rel-10	RBS-3412a
– DCH quality target									RBS-3413
– Downlink transport channel type						HS-DSCH			RBS-3414
– DL Transport channel identity						Not Present			RBS-3415
– CHOICE DL parameters						HS-DSCH			RBS-3416
– HARQ Info									RBS-3417
– Number of Processes						Reference to clause 6.10 Parameter Set			RBS-3418
– CHOICE Memory Partitioning						Implicit			RBS-3419
– CHOICE DL MAC header type						MAC-ehs			RBS-3420
– Added or reconfigured MAC-ehs reordering queue									RBS-3421
– MAC-ehs queue to add or reconfigure list						(one queue)			RBS-3422
– MAC-ehs queue Id						0 (for DTCH)			RBS-3423
– T1						50			RBS-3424
– MAC-ehs window size						64			RBS-3425
– DCH quality target						Not present			RBS-3426
Frequency info			A1, A2, A3, A4, A5, A7, A8, 11						RBS-3438
			, A9, A10					Rel-5	RBS-3439
			, A12, A13, A14, A15, A16					Rel-6	RBS-3440
			, A17, A17a, A17b, A17c, A17d, A17e, , A17f A18, A19, A19a, A19b, A20, A21, A22, A24					Rel-7	RBS-3441
			, A23, A28a					Rel-7	RBS-3442
			, A25, A25a, A25b, A26, A27, A27a, A28, A30					Rel-8	RBS-3443
			, A25c					Rel-9	RBS-3444
– UARFCN uplink (Nu)						Reference to clause 5.1 Test frequencies. This IE should be present, if the default duplex distance defined for the operating frequency band is not used and frequency is different from the current frequency, otherwise set to Not Present.			RBS-3445
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies if frequency is different from the current frequency otherwise set to Not Present.			RBS-3446
Frequency info			A6			Not Present			RBS-3447
			, A29					Rel-8	RBS-3448
			, A31, A32 , A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-3449
DTX-DRX timing information			A20, A21					Rel-7	RBS-3450
			, A23					Rel-7 Rel-8	RBS-3451
CHOICE timing									RBS-3452
– New timing									RBS-3453
– Enabling Delay						0			RBS-3454
– UE DTX DRX Offset						1 if 2ms TTI selected, otherwise 0			RBS-3455
DTX-DRX Information									RBS-3456
– CHOICE E-DCH TTI length						Unless stated otherwise, this should be set to 2ms if the UE supports 2ms TTI, or 10ms if the UE does not support 2ms TTI.			RBS-3457
– UE DTX cycle 1						8 if 2ms TTI selected, otherwise 10			RBS-3458
– UE DTX cycle 2						16 if 2ms TTI selected, otherwise 20			RBS-3459
– MAC DTX cycle						8 if 2ms TTI selected, otherwise 10			RBS-3460
– Inactivity Threshold for UE DTX cycle 2						32 if 2ms TTI selected, otherwise 8			RBS-3461
– UE DTX long preamble length						4			RBS-3462
– MAC Inactivity Threshold						1 if 2ms TTI selected, otherwise 8			RBS-3463
– CQI DTX Timer						32			RBS-3464
– UE DPCCH burst_1						1			RBS-3465
– UE DPCCH burst_2						1			RBS-3466
DRX Information									RBS-3467
– UE DRX cycle						8 if 2ms TTI selected, otherwise 10			RBS-3468
– Inactivity Threshold for UE DRX cycle						32			RBS-3469
– Inactivity Threshold for UE Grant Monitoring						32 if 2ms TTI selected, otherwise 8			RBS-3470
– UE DRX Grant Monitoring						TRUE			RBS-3471
Uplink DPCCH slot format information						1			RBS-3472
HS-SCCH less information						Not Present			RBS-3473
MIMO parameters			A28a , A28					Rel-7 Rel-8	RBS-3474
– MIMO operation						start			RBS-3475
– CHOICE mode						FDD			RBS-3476
– MIMO N_cqi_typeA/M_cqi ratio						1/1			RBS-3477
– MIMO pilot configuration									RBS-3478
– CHOICE Second CPICH pattern						Antenna1 S-CPICH			RBS-3479
– Channelisation code						12			RBS-3480
MIMO parameters			A31 , A34					Rel-9 Rel-10	RBS-3481
– MIMO operation						start			RBS-3482
– CHOICE mode						FDD			RBS-3483
– MIMO N_cqi_typeA/M_cqi ratio						1/1			RBS-3484
– MIMO pilot configuration									RBS-3485
-CHOICE Second CPICH pattern						Antenna1 S-CPICH			RBS-3486
– Channelisation code						13			RBS-3487
– Power Offset for S-CPICH for MIMO						0			RBS-3488
– Precoding weight set restriction						True			RBS-3489
MIMO parameters			A32, A33					Rel-9 Rel-10	RBS-3490
– MIMO operation						start			RBS-3491
– CHOICE mode						FDD			RBS-3492
– MIMO N_cqi_typeA/M_cqi ratio						1/1			RBS-3493
– MIMO pilot configuration									RBS-3494
-CHOICE Second CPICH pattern						Antenna1 S-CPICH			RBS-3495
– Channelisation code						29			RBS-3496
– Power Offset for S-CPICH for MIMO						0			RBS-3497
– Precoding weight set restriction						True			RBS-3498
Maximum allowed UL TX power			A1, A2, A3, A4, A7, A8, A11			33dBm			RBS-3499
			, A9, A10					Rel-5	RBS-3500
			, A12, A13, A14, A15, A16					Rel-6	RBS-3501
			, A17, A17a, A17b, A17c, A17d, A17e, , A17f A18, A19, A19a, A19b, A20, A21, A22, A24					Rel-7	RBS-3502
			, A23, A28a					Rel-7 Rel-8	RBS-3503
			, A25, A25a, A25b, A26, A27, A27a, A28, A29, A30					Rel-8	RBS-3504
			, A25c					Rel-9	RBS-3505
			, A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-10 Rel-11	RBS-3506
Maximum allowed UL TX power			A5, A6			Not Present			RBS-3507
CHOICE channel requirement			A1, A2, A3, A4, A7, A8, A11			Uplink DPCH info		Rel-5 and earlier	RBS-3508
– Uplink DPCH power control info									RBS-3509
– DPCCH power offset						-40 (-80dB)			RBS-3510
– PC Preamble						1 frame			RBS-3511
– SRB delay						7 frames			RBS-3512
– Power Control Algorithm						Algorithm1			RBS-3513
– TPC step size						0 (1dB)			RBS-3514
– NACK						Not Present		Rel-5	RBS-3515
– NACK						Not Present		Rel-5	RBS-3516
– Ack-Nack repetition factor						Not Present		Rel-5	RBS-3517
– Scrambling code type						Long			RBS-3518
– Scrambling code number						0 (0 to 16777215)			RBS-3519
– Number of DPDCH						Not Present(1)			RBS-3520
– spreading factor						Reference to clause 6.10 Parameter Set			RBS-3521
– TFCI existence						Reference to clause 6.10 Parameter Set			RBS-3522
– Number of FBI bit						Reference to clause 6.10 Parameter Set			RBS-3523
– Puncturing Limit						Reference to clause 6.10 Parameter Set			RBS-3524
– Number of TPC bits						Not Present		Rel-7	RBS-3525
CHOICE channel requirement			A9, A10			Uplink DPCH info		Rel-5	RBS-3526
			, A17, A17a, A18					Rel-7	RBS-3527
			, A25a, A28					Rel-8	RBS-3528
– Uplink DPCH power control info									RBS-3529
– DPCCH power offset						-40 (-80dB)			RBS-3530
– PC Preamble						1 frame			RBS-3531
– SRB delay						7 frames			RBS-3532
– Power Control Algorithm						Algorithm1			RBS-3533
– TPC step size						0 (1dB)			RBS-3534
– ACK						3			RBS-3535
– NACK						3			RBS-3536
– Ack-Nack repetition factor						1			RBS-3537
– HARQ_preamble_mode						0		Rel-6	RBS-3538
– Scrambling code type						Long			RBS-3539
– Scrambling code number						0 (0 to 16777215)			RBS-3540
– Number of DPDCH						Not Present(1)			RBS-3541
– spreading factor						Reference to clause 6.10 Parameter Set			RBS-3542
– TFCI existence						Reference to clause 6.10 Parameter Set			RBS-3543
– Number of FBI bit						Reference to clause 6.10 Parameter Set			RBS-3544
– Puncturing Limit						Reference to clause 6.10 Parameter Set			RBS-3545
CHOICE channel requirement			A5,A6			Not Present		Rel-5 and earlier	RBS-3546
Uplink DPCH info			A12					Rel-6	RBS-3547
			, A19 A35 A38, A39, A40, A41, A42, A43, A44, A45					Rel-7 Rel-10 Rel-11	RBS-3548
– Uplink DPCH power control info									RBS-3549
– DPCCH power offset						-40 (-80dB)			RBS-3550
– PC Preamble						1 frame			RBS-3551
– SRB delay						7 frames			RBS-3552
– Power Control Algorithm						Algorithm1			RBS-3553
– TPC step size						0 (1dB)			RBS-3554
– ACK						3			RBS-3555
– NACK						3			RBS-3556
– Ack-Nack repetition factor						1			RBS-3557
– HARQ_preamble_mode						0			RBS-3558
– Scrambling code type						Long			RBS-3559
– Scrambling code number						0 (0 to 16777215)			RBS-3560
– Number of DPDCH						Not Present(1)			RBS-3561
– spreading factor						Reference to clause 6.10 Parameter Set			RBS-3562
– TFCI existence						Reference to clause 6.10 Parameter Set			RBS-3563
– Number of FBI bit						Reference to clause 6.10 Parameter Set			RBS-3564
– Puncturing Limit						Reference to clause 6.10 Parameter Set			RBS-3565
– Number of TPC bits						Not Present		Rel-7	RBS-3566
Uplink DPCH info			A13, A14, A15, A16					Rel-6	RBS-3567
			, A17b, A17c, A17d, A17e, , A17f A19a, A19b, A20, A21, A22					Rel-7	RBS-3568
			, A23, A28a					Rel-7 Rel-8	RBS-3569
			, A25, A25b, A26, A27, A27a, A30					Rel-8	RBS-3570
			, A25c A33, A34, A36, A37					Rel-9 Rel-10	RBS-3571
– Uplink DPCH power control info									RBS-3572
– DPCCH power offset						-40 (-80dB)			RBS-3573
– PC Preamble						1 frame			RBS-3574
– SRB delay						7 frames			RBS-3575
– Power Control Algorithm						Algorithm1			RBS-3576
– TPC step size						0 (1dB)			RBS-3577
– ACK						3			RBS-3578
– NACK						3			RBS-3579
– Ack-Nack repetition factor						1			RBS-3580
– HARQ_preamble_mode						0			RBS-3581
– Scrambling code type						Long			RBS-3582
– Scrambling code number						0 (0 to 16777215)			RBS-3583
– Number of DPDCH						0			RBS-3584
– spreading factor						Not Present			RBS-3585
– TFCI existence						FALSE			RBS-3586
– Number of FBI bit						Not Present			RBS-3587
– Puncturing Limit						Not Present			RBS-3588
– Number of TPC bits						Not Present		Rel-7	RBS-3589
Uplink DPCH info			A24, A29			Not Present		Rel-7	RBS-3590
Uplink DPCH info			A31, A32					Rel-9	RBS-3591
– Uplink DPCH power control info									RBS-3592
– DPCCH power offset						-40 (-80dB)			RBS-3593
– PC Preamble						1 frame			RBS-3594
– SRB delay						7 frames			RBS-3595
– Power Control Algorithm						Algorithm1			RBS-3596
– TPC step size						0 (1dB)			RBS-3597
– ∆ACK						3			RBS-3598
– ∆NACK						3			RBS-3599
– Ack-Nack repetition factor						1			RBS-3600
– HARQ_preamble_mode						0			RBS-3601
– Scrambling code type						Short			RBS-3602
– Scrambling code number						0 (0 to 16777215)			RBS-3603
– Number of DPDCH						Not Present(1)			RBS-3604
– spreading factor						Reference to clause 6.10 Parameter Set			RBS-3605
– TFCI existence						Reference to clause 6.10 Parameter Set			RBS-3606
– Number of FBI bit						Reference to clause 6.10 Parameter Set			RBS-3607
– Puncturing Limit						Reference to clause 6.10 Parameter Set			RBS-3608
– Number of TPC bits						Not Present			RBS-3609
E-DCH info			A12, A13, A14, A15, A16					Rel-6	RBS-3610
			, A17b, A17c, A17d, A17e, , A17f A20, A21, A22					Rel-7	RBS-3611
			, A23					Rel-7 Rel-8	RBS-3612
			, A25, A25b, A26, A27, A30					Rel-8	RBS-3613
			, A25c , A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-3614
– MAC- e/es reset indicator						TRUE			RBS-3615
– E-DPCCH info									RBS-3616
– E-DPCCH/DPCCH power offset						0			RBS-3617
– Happy bit delay condition						100 ms			RBS-3618
– E-TFC Boost Info						Not Present		Rel-7	RBS-3619
– E-DPDCH power interpolation						Not Present		Rel-7	RBS-3620
– E-DPDCH info									RBS-3621
– E-TFCI table index						0			RBS-3622
– E-DCH minimum set E-TFCI						9			RBS-3623
– Reference E-TFCIs						2 E-TFCIs			RBS-3624
– Reference E-TFCI						11			RBS-3625
– Reference E-TFCI PO						4			RBS-3626
– Reference E-TFCI						83			RBS-3627
– Reference E-TFCI PO						16			RBS-3628
– Maximum channelisation codes						2sf4			RBS-3629
– PLnon-max						0.84			RBS-3630
– Scheduling Information Configuration									RBS-3631
– Periodicity for Scheduling Info – no grant						Not present			RBS-3632
– Periodicity for Scheduling Info – grant						Not present			RBS-3633
– Power Offset for Scheduling Info						0			RBS-3634
– 3-Index-Step Threshold						Not present			RBS-3635
– 2-Index-Step Threshold						Not present			RBS-3636
– Scheduled Transmission configuration									RBS-3637
– 2ms scheduled transmission grant HARQ process allocation						Not present			RBS-3638
– Serving Grant						Not present			RBS-3639
-UL 16QAM settings						Not Present		Rel-7	RBS-3640
E-DCH info			A19					Rel-7	RBS-3641
			, A27a					Rel-8	RBS-3642
– MAC- e/es reset indicator						TRUE			RBS-3643
– E-DPCCH info									RBS-3644
– E-DPCCH/DPCCH power offset						0			RBS-3645
– Happy bit delay condition						100 ms			RBS-3646
– E-TFC Boost Info						Not Present		Rel-7	RBS-3647
– E-DPDCH power interpolation						Not Present		Rel-7	RBS-3648
– E-DPDCH info									RBS-3649
– E-TFCI table index						0			RBS-3650
– E-DCH minimum set E-TFCI						9			RBS-3651
– Reference E-TFCIs						2 E-TFCIs			RBS-3652
– Reference E-TFCI						11			RBS-3653
– Reference E-TFCI PO						4			RBS-3654
– Reference E-TFCI						83			RBS-3655
– Reference E-TFCI PO						16			RBS-3656
– Maximum channelisation codes						2sf2and2sf4			RBS-3657
– PLnon-max						0.84			RBS-3658
– Scheduling Information Configuration									RBS-3659
– Periodicity for Scheduling Info – no grant						Not present			RBS-3660
– Periodicity for Scheduling Info – grant						Not present			RBS-3661
– Power Offset for Scheduling Info						0			RBS-3662
– 3-Index-Step Threshold						Not present			RBS-3663
– 2-Index-Step Threshold						Not present			RBS-3664
– Scheduled Transmission configuration									RBS-3665
– 2ms scheduled transmission grant HARQ process allocation						Not present			RBS-3666
– Serving Grant						Not present			RBS-3667
-UL 16QAM settings								Rel-7	RBS-3668
-BetaEd gain E-AGCH table selection						1			RBS-3669
E-DCH info			A19a, A19b					Rel-7 Rel-7 Rel-7 Rel-7	RBS-3670 RBS-3671 RBS-3672
						TRUE 0 100 ms Not Present Not Present 0 10 3 E-TFCIs 105 12 116 14 127 16 2sf2and2sf4 0.84 Not present Not present 0 Not present Not present Not present Not present 1
– MAC- e/es reset indicator – E-DPCCH info – E-DPCCH/DPCCH power offset – Happy bit delay condition – E-TFC Boost Info – E-DPDCH power interpolation – E-DPDCH info – E-TFCI table index – E-DCH minimum set E-TFCI – Reference E-TFCIs – Reference E-TFCI – Reference E-TFCI PO – Reference E-TFCI – Reference E-TFCI PO – Reference E-TFCI – Reference E-TFCI PO – Maximum channelisation codes – PLnon-max – Scheduling Information Configuration – Periodicity for Scheduling Info – no grant – Periodicity for Scheduling Info – grant – Power Offset for Scheduling Info – 3-Index-Step Threshold – 2-Index-Step Threshold – Scheduled Transmission configuration – 2ms scheduled transmission grant HARQ process allocation – Serving Grant -UL 16QAM settings -BetaEd gain E-AGCH table selection
E-DCH info			A24			Not Present		Rel-7	RBS-3673
			, A29					Rel-8	RBS-3674
Uplink secondary cell info FDD			, A31, A32 , A33, A34, A35, A36, A37			Not Present		Rel-9 Rel-10	RBS-3675
Uplink secondary cell info FDD			A25c					Rel-9	RBS-3676
– Secondary serving E-DCH cell info									RBS-3677
– Primary E-RNTI						‘1010 1010 1010 1011’			RBS-3678
– Secondary E-RNTI						Not Present			RBS-3679
– Secondary E-DCH info common									RBS-3680
– Frequency info									RBS-3681
– UARFCN uplink (Nu)						Reference to clause 5.1 Test frequencies			RBS-3682
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-3683
– Scrambling code type						Long			RBS-3684
– Scrambling code number						0			RBS-3685
– 2ms scheduled transmission grant HARQ process allocation						Not Present			RBS-3686
– Serving Grant									RBS-3687
– Primary/Secondary Grant Selector						Primary			RBS-3688
– Minimum reduced E-DPDCH gain factor.						21/15			RBS-3689
– E-DCH minimum set E-TFCI						1			RBS-3690
– DPCCH Power offset for secondary UL frequency						0 dB			RBS-3691
– PC Preamble						0 frame			RBS-3692
– Downlink information per radio link list on secondary UL frequency									RBS-3693
– Downlink information for each radio link on secondary UL frequency						1			RBS-3694
– Primary CPICH info									RBS-3695
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-3696
– Cell ID						Not Present			RBS-3697
– Downlink F-DPCH info for each RL on secondary UL frequency									RBS-3698
– Downlink F-DPCH info for each RL									RBS-3699
– Primary CPICH usage for channel estimate									RBS-3700
– F-DPCH frame offset						Set to value Default DPCH Offset Value (as currently stored in SS) mod 38 400			RBS-3701
– F-DPCH slot format						3 if UE supports enhanced F-DPCH, otherwise Not Present			RBS-3702
– Secondary CPICH info						Not Present			RBS-3703
– Secondary scrambling code						Not Present			RBS-3704
– Code number						11			RBS-3705
– TPC combination index						0			RBS-3706
– STTD indication						Not Present			RBS-3707
– E-AGCH Info									RBS-3708
– E-AGCH Channelisation Code						10			RBS-3709
– E-HICH Info									RBS-3710
– Channelisation Code						4			RBS-3711
– Signature Sequence						1			RBS-3712
– E-RGCH Info									RBS-3713
– Signature Sequence						0			RBS-3714
– RG combination index						0			RBS-3715
CHOICE Mode			A1, A2, A3, A4, A5, A6, A7, A8, A11			FDD		R99 and Rel-4 only	RBS-3716
– Downlink PDSCH information						Not Present			RBS-3717
Downlink HS-PDSCH Information			A1, A2, A3, A4, A5, A6, A7, A8, A11			Not Present		Rel-5	RBS-3718
Downlink HS-PDSCH Information			A9, A10					Rel-5	RBS-3719
Downlink HS-PDSCH Information			, A12, A13, A14, A15, A16					Rel-6	RBS-3720
			, A17, A17d, A18, A19, A19a, A19b, A20, A21, A22, A24					Rel-7	RBS-3721
			, A25, A25b, A29					Rel-8	RBS-3722
– HS-SCCH Info									RBS-3723
– CHOICE mode						FDD			RBS-3724
– DL Scrambling Code						Not present			RBS-3725
– HS-SCCH Channelisation Code Information									RBS-3726
– HS-SCCH Channelisation Code						7			RBS-3727
– Measurement Feedback Info									RBS-3728
– CHOICE mode						FDD			RBS-3729
– POhsdsch						6 dB			RBS-3730
– CQI Feedback cycle, k						4 ms			RBS-3731
– CQI repetition factor						1			RBS-3732
– CQI						5 (corresponds to 0dB in relative power offset)			RBS-3733
– CHOICE mode						FDD (no data)			RBS-3734
– Downlink 64QAM configured						Not present		Rel-7	RBS-3735
– HS-DSCH TB size table						Not present		Rel-7	RBS-3736
Downlink HS-PDSCH Information			A25a					Rel-8	RBS-3737
– HS-SCCH Info									RBS-3738
– CHOICE mode						FDD			RBS-3739
– DL Scrambling Code						Not present			RBS-3740
– HS-SCCH Channelisation Code Information									RBS-3741
– HS-SCCH Channelisation Code						7			RBS-3742
– Measurement Feedback Info									RBS-3743
– CHOICE mode						FDD			RBS-3744
– POhsdsch						6 dB			RBS-3745
– CQI Feedback cycle, k						4 ms			RBS-3746
– CQI repetition factor						1			RBS-3747
– CQI						5 (corresponds to 0dB in relative power offset)			RBS-3748
– CHOICE mode						FDD (no data)			RBS-3749
– Downlink 64QAM configured						Not present		Rel-7	RBS-3750
– HS-DSCH TB size table						Octet Aligned		Rel-7	RBS-3751
Downlink HS-PDSCH Information			A17a					Rel-7	RBS-3752
			, A28					Rel-8	RBS-3753
– HS-SCCH Info									RBS-3754
– CHOICE mode						FDD			RBS-3755
– DL Scrambling Code						Not Present			RBS-3756
– HS-SCCH Channelisation Code Information									RBS-3757
– HS-SCCH Channelisation Code						4			RBS-3758
– HS-SCCH Channelisation Code						5			RBS-3759
– Measurement Feedback Info									RBS-3760
– CHOICE mode						FDD			RBS-3761
– POhsdsch						6 dB			RBS-3762
– CQI Feedback cycle, k						4 ms			RBS-3763
– CQI repetition factor						1			RBS-3764
– CQI						5 (corresponds to 0dB in relative power offset)			RBS-3765
– CHOICE mode						FDD			RBS-3766
– Downlink 64QAM configured						TRUE		Rel-7	RBS-3767
– HS-DSCH TB size table						Octet Aligned		Rel-7	RBS-3768
Downlink HS-PDSCH Information			A17b					Rel-7	RBS-3769
			, A23					Rel-7 Rel-8	RBS-3770
			, A26, A27, A27a, A30 A25c, A41, A42, A43					Rel-8 Rel-9, Rel-11	RBS-3771
– HS-SCCH Info									RBS-3772
– CHOICE mode						FDD			RBS-3773
– DL Scrambling Code						Not present			RBS-3774
– HS-SCCH Channelisation Code Information									RBS-3775
– HS-SCCH Channelisation Code						7			RBS-3776
– Measurement Feedback Info									RBS-3777
– CHOICE mode						FDD			RBS-3778
– POhsdsch						6 dB			RBS-3779
– CQI Feedback cycle, k						4 ms			RBS-3780
– CQI repetition factor						1			RBS-3781
– CQI						5 (corresponds to 0dB in relative power offset)			RBS-3782
– CHOICE mode						FDD (no data)			RBS-3783
– Downlink 64QAM configured						Not present		Rel-7	RBS-3784
– HS-DSCH TB size table						Octet Aligned		Rel-7	RBS-3785
Downlink HS-PDSCH Information			A17c, A17e, A17f					Rel-7	RBS-3786
– HS-SCCH Info									RBS-3787
– CHOICE mode						FDD			RBS-3788
– DL Scrambling Code						Not Present			RBS-3789
– HS-SCCH Channelisation Code Information									RBS-3790
– HS-SCCH Channelisation Code						6			RBS-3791
– HS-SCCH Channelisation Code						7			RBS-3792
– Measurement Feedback Info									RBS-3793
– CHOICE mode						FDD			RBS-3794
– Pohsdsch						6 dB			RBS-3795
– CQI Feedback cycle, k						4 ms			RBS-3796
– CQI repetition factor						1			RBS-3797
– CQI						5 (corresponds to 0dB in relative power offset)			RBS-3798
– CHOICE mode						FDD			RBS-3799
– Downlink 64QAM configured						TRUE			RBS-3800
– HS-DSCH TB size table						Octet Aligned			RBS-3801
Downlink HS-PDSCH Information	A28a							Rel-7	RBS-3802
– HS-SCCH Info									RBS-3803
– CHOICE mode						FDD			RBS-3804
– DL Scrambling Code						Not Present			RBS-3805
– HS-SCCH Channelisation Code Information									RBS-3806
– HS-SCCH Channelisation Code						4			RBS-3807
– HS-SCCH Channelisation Code						5			RBS-3808
– Measurement Feedback Info									RBS-3809
– CHOICE mode						FDD			RBS-3810
– Pohsdsch						6 dB			RBS-3811
– CQI Feedback cycle, k						4 ms			RBS-3812
– CQI repetition factor						1			RBS-3813
– CQI						5 (corresponds to 0dB in relative power offset)			RBS-3814
– CHOICE mode						FDD			RBS-3815
– Downlink 64QAM configured						Not Present			RBS-3816
– HS-DSCH TB size table						Not Present			RBS-3817
Downlink HS-PDSCH Information	A31 , A34, A36							Rel-9 Rel-10	RBS-3818
– HS-SCCH Info									RBS-3819
– CHOICE mode						FDD			RBS-3820
– DL Scrambling Code						Not Present			RBS-3821
– HS-SCCH Channelisation Code Information									RBS-3822
– HS-SCCH Channelisation Code						6			RBS-3823
– HS-SCCH Channelisation Code						7			RBS-3824
– Measurement Feedback Info									RBS-3825
– CHOICE mode						FDD			RBS-3826
– Pohsdsch						8 dB			RBS-3827
– CQI Feedback cycle, k						8 ms			RBS-3828
– CQI repetition factor						1			RBS-3829
– CQI						4 (corresponds to 0dB in relative power offset)			RBS-3830
– CHOICE mode						FDD			RBS-3831
– Downlink 64QAM configured						Not Present			RBS-3832
– HS-DSCH TB size table						Not Present			RBS-3833
Downlink HS-PDSCH Information	A32 , A33, A35, A37 A38, A39, A40, A44, A45							Rel-9 Rel-10 Rel-11	RBS-3834
– HS-SCCH Info									RBS-3835
– CHOICE mode						FDD			RBS-3836
– DL Scrambling Code						Not Present			RBS-3837
– HS-SCCH Channelisation Code Information									RBS-3838
– HS-SCCH Channelisation Code						Refer to clause 5.5.1.3			RBS-3839
– Measurement Feedback Info									RBS-3840
– CHOICE mode						FDD			RBS-3841
– Pohsdsch						8 dB			RBS-3842
– CQI Feedback cycle, k						8 ms			RBS-3843
– CQI repetition factor						1			RBS-3844
– CQI						4 (corresponds to 0dB in relative power offset)			RBS-3845
– CHOICE mode						FDD			RBS-3846
– Downlink 64QAM configured						TRUE			RBS-3847
– HS-DSCH TB size table						Not present			RBS-3848
Downlink information common for all radio links			A1, A2, A3, A11						RBS-3865
– Downlink DPCH info common for all RL									RBS-3866
– Timing indicator						Maintain			RBS-3867
– CFN-targetSFN frame offset						Not Present			RBS-3868
– Downlink DPCH power control information									RBS-3869
– DPC mode						0 (single)			RBS-3870
– CHOICE mode						FDD			RBS-3871
– Power offset PPilot-DPDCH						0			RBS-3872
– DL rate matching restriction information						Not Present			RBS-3873
– Spreading factor						Reference to clause 6.10 Parameter Set			RBS-3874
– Fixed or Flexible Position						Reference to clause 6.10 Parameter Set			RBS-3875
– TFCI existence						Reference to clause 6.10 Parameter Set			RBS-3876
– CHOICE SF						Reference to clause 6.10 Parameter Set			RBS-3877
– CHOICE mode						FDD			RBS-3878
– DPCH compressed mode info						Not Present			RBS-3879
– TX Diversity mode						None			RBS-3880
– SSDT information						Not Present		R99 and Rel-4 only	RBS-3881
– Default DPCH Offset Value						Not Present			RBS-3882
Downlink information common for all radio links			A9					Rel-5	RBS-3883
Downlink information common for all radio links			, A12, A13, A15					Rel-6	RBS-3884
			, A17, A17a, A17d, A17e, , A17f A18. A19, A19a					Rel-7	RBS-3885
			, A25a, A25b, A26, A28					Rel-8	RBS-3886
			A35					Rel-10	RBS-3886a
			A38, A39, A40, A41, A42, A43, A44, A45					Rel-11	RBS-3886b
– Downlink DPCH info common for all RL									RBS-3887
– Timing indicator						Maintain			RBS-3888
– CFN-targetSFN frame offset						Not Present			RBS-3889
– Downlink DPCH power control information									RBS-3890
– DPC mode						0 (single)			RBS-3891
– CHOICE mode						FDD			RBS-3892
– Power offset PPilot-DPDCH						0			RBS-3893
– DL rate matching restriction information						Not Present			RBS-3894
– Spreading factor						Reference to clause 6.10 Parameter Set			RBS-3895
– Fixed or Flexible Position						Reference to clause 6.10 Parameter Set			RBS-3896
– TFCI existence						Reference to clause 6.10 Parameter Set			RBS-3897
– CHOICE SF						Reference to clause 6.10 Parameter Set			RBS-3898
– CHOICE mode						FDD			RBS-3899
– DPCH compressed mode info						Not Present			RBS-3900
– TX Diversity mode						None			RBS-3901
– Default DPCH Offset Value						Not Present			RBS-3902
– MAC-hs reset indicator						Not Present			RBS-3903
Downlink information common for all radio links			A4,A7,A8						RBS-3904
– Downlink DPCH info common for all RL									RBS-3905
– Timing indicator						Initialize			RBS-3906
– CFN-targetSFN frame offset						Not Present			RBS-3907
– Downlink DPCH power control information									RBS-3908
– DPC mode						0 (single)			RBS-3909
– CHOICE mode						FDD			RBS-3910
– Power offset PPilot-DPDCH						0			RBS-3911
– DL rate matching restriction information						Not Present			RBS-3912
– Spreading factor						Reference to clause 6.10 Parameter Set			RBS-3913
– Fixed or Flexible Position						Reference to clause 6.10 Parameter Set			RBS-3914
– TFCI existence						Reference to clause 6.10 Parameter Set			RBS-3915
– CHOICE SF						Reference to clause 6.10 Parameter Set			RBS-3916
– CHOICE mode						FDD			RBS-3917
– DPCH compressed mode info						Not Present			RBS-3918
– TX Diversity mode						None			RBS-3919
– SSDT information						Not Present		R99 and Rel-4 only	RBS-3920
– Default DPCH Offset Value						Arbitrary set to value 0..306688 by step of 512			RBS-3921
Downlink information common for all radio links			A10					Rel-5	RBS-3922
– Downlink DPCH info common for all RL									RBS-3923
– Timing indicator						Initialize			RBS-3924
– CFN-targetSFN frame offset						Not Present			RBS-3925
– Downlink DPCH power control information									RBS-3926
– DPC mode						0 (single)			RBS-3927
– CHOICE mode						FDD			RBS-3928
– Power offset PPilot-DPDCH						0			RBS-3929
– DL rate matching restriction information						Not Present			RBS-3930
– Spreading factor						Reference to clause 6.10 Parameter Set			RBS-3931
– Fixed or Flexible Position						Reference to clause 6.10 Parameter Set			RBS-3932
– TFCI existence						Reference to clause 6.10 Parameter Set			RBS-3933
– CHOICE SF						Reference to clause 6.10 Parameter Set			RBS-3934
– CHOICE mode						FDD			RBS-3935
– DPCH compressed mode info						Not Present			RBS-3936
– TX Diversity mode						None			RBS-3937
– Default DPCH Offset Value						Arbitrary set to value 0..306688 by step of 512			RBS-3938
– MAC-hs reset indicator						Not Present			RBS-3939
Downlink information common for all radio links			A14, A16					Rel-6	RBS-3940
			, A17b, A17c, A19b, A20, A21, A22					Rel-7	RBS-3941
			, A23, A28a					Rel-7 Rel-8	RBS-3942
			, A25, A27, A27a A25c, A31, A32					Rel-8 Rel-9	RBS-3943
			A33, A34, A36, A37					Rel-10	RBS-3943a
– Downlink F-DPCH info common for all RL									RBS-3944
– Timing Indication						Maintain			RBS-3945
– Timing maintained Synchronization indicator						FALSE			RBS-3946
– Downlink F-DPCH power control information									RBS-3947
– DPC mode						0 (single)			RBS-3948
– TPC command error rate target						0.04			RBS-3949
– CHOICE mode						FDD			RBS-3950
– DPCH compressed mode info						Not Present			RBS-3951
– TX Diversity mode						None			RBS-3952
– Default DPCH Offset Value						Not Present			RBS-3953
– MAC-hs reset indicator						Not Present			RBS-3954
Downlink information common for all radio links			A5,A6			Not Present			RBS-3955
			, A24			Not Present		Rel-7	RBS-3956
			, A29						RBS-3957
Downlink information common for all radio links – Downlink F-DPCH info common for all RL – Timing Indication – Downlink F-DPCH power control Information – DPC mode – TPC command error rate target – CHOICE mode – DPCH compressed mode info – TX Diversity mode – Default DPCH Offset Value – MAC-hs reset indicator			A30			Initialise 0 (single) 0.04 FDD Not Present None Arbitrary set to value 0..306688 by step of 512 TRUE		Rel-8	RBS-3957a
Downlink information for each radio link list			A1, A2, A3, A4, A7, A8, A11						RBS-3958
– Downlink information for each radio link									RBS-3959
– Choice mode						FDD			RBS-3960
– Primary CPICH info									RBS-3961
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-3962
– PDSCH with SHO DCH info						Not Present		R99 and Rel-4 only	RBS-3963
– PDSCH code mapping						Not Present		R99 and Rel-4 only	RBS-3964
– Serving HS-DSCH radio link indicator						FALSE		Rel-5	RBS-3965
– Downlink DPCH info for each RL									RBS-3966
– Primary CPICH usage for channel estimation						Primary CPICH may be used			RBS-3967
– DPCH frame offset						Set to value Default DPCH Offset Value (as currently stored in SS) mod 38 400			RBS-3968
– Secondary CPICH info						Not Present			RBS-3969
– DL channelisation code									RBS-3970
– Secondary scrambling code						1			RBS-3971
– Spreading factor						Reference to clause 6.10 Parameter Set			RBS-3972
– Code number						0			RBS-3973
– Scrambling code change						Set to value Default1: No code change (if the UE has a compressed mode pattern sequence configured in variable TGPS_IDENTITY or included in the message including IE "Downlink DPCH info for each RL", which is using compressed mode method "SF/2") Set to value Default2: OMIT (otherwise)			RBS-3974
– TPC combination index						0			RBS-3975
– SSDT Cell Identity						Not Present		R99 and Rel-4 only	RBS-3976
– Closed loop timing adjustment mode						Not Present			RBS-3977
– SCCPCH information for FACH						Not Present		R99 and Rel-4 only	RBS-3978
Downlink information for each radio link list			A5						RBS-3979
– Downlink information for each radio link									RBS-3980
– Choice mode						FDD			RBS-3981
– Primary CPICH info									RBS-3982
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-3983
– PDSCH with SHO DCH info						Not Present		R99 and Rel-4 only	RBS-3984
– PDSCH code mapping						Not Present		R99 and Rel-4 only	RBS-3985
– Serving HS-DSCH radio link indicator						FALSE		Rel-5	RBS-3986
– Downlink DPCH info for each RL						Not present			RBS-3987
– SCCPCH information for FACH						Not Present		R99 and Rel-4 only	RBS-3988
Downlink information for each radio link list			A9, A10					Rel-5	RBS-3989
			, A17, A18					Rel-7	RBS-3990
– Downlink information for each radio link									RBS-3991
– Choice mode						FDD			RBS-3992
– Primary CPICH info									RBS-3993
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-3994
– PDSCH with SHO DCH info						Not Present		R99 and Rel-4 only	RBS-3995
– PDSCH code mapping						Not Present		R99 and Rel-4 only	RBS-3996
– Serving HS-DSCH radio link indicator						TRUE			RBS-3997
– Serving E-DCH radio link indicator						FALSE		Rel-6	RBS-3998
– Downlink DPCH info for each RL									RBS-3999
– Primary CPICH usage for channel estimation						Primary CPICH may be used			RBS-4000
– DPCH frame offset						Set to value Default DPCH Offset Value (as currently stored in SS) mod 38 400			RBS-4001
– Secondary CPICH info						Not Present			RBS-4002
– DL channelisation code									RBS-4003
– Secondary scrambling code						1			RBS-4004
– Spreading factor						Reference to clause 6.10 Parameter Set			RBS-4005
– Code number						0			RBS-4006
– Scrambling code change						Set to value Default1: No code change (if the UE has a compressed mode pattern sequence configured in variable TGPS_IDENTITY or included in the message including IE "Downlink DPCH info for each RL", which is using compressed mode method "SF/2") Set to value Default2: OMIT (otherwise)			RBS-4007
– TPC combination index						0			RBS-4008
– SSDT Cell Identity						Not Present		R99 and Rel-4 only	RBS-4009
– Closed loop timing adjustment mode						Not Present			RBS-4010
– E-AGCH Info						Not Present		Rel-6	RBS-4011
– CHOICE E-HICH Information						Not Present		Rel-6	RBS-4012
– CHOICE E-RGCH Information						Not Present		Rel-6	RBS-4013
– SCCPCH information for FACH						Not Present		R99 and Rel-4 only	RBS-4014
Downlink information for each radio link list			A17a, A17d, A17e,					Rel-7	RBS-4015
			, A25a, A28					Rel-8	RBS-4016
– Downlink information for each radio link									RBS-4017
– Choice mode						FDD			RBS-4018
– Primary CPICH info									RBS-4019
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4020
– Serving HS-DSCH radio link indicator						TRUE			RBS-4021
– Serving E-DCH radio link indicator						FALSE		Rel-6	RBS-4022
– Downlink DPCH info for each RL									RBS-4023
– Primary CPICH usage for channel estimation						Primary CPICH may be used			RBS-4024
– DPCH frame offset						Set to value Default DPCH Offset Value (as currently stored in SS) mod 38 400			RBS-4025
– Secondary CPICH info						Not Present			RBS-4026
– DL channelisation code									RBS-4027
– Secondary scrambling code						Not Present			RBS-4028
– Spreading factor						Reference to clause 6.10 Parameter Set			RBS-4029
– Code number						13			RBS-4030
– Scrambling code change						Not Present			RBS-4031
– TPC combination index						0			RBS-4032
– Closed loop timing adjustment mode						Not Present			RBS-4033
– E-AGCH Info						Not Present		Rel-6	RBS-4034
– CHOICE E-HICH Information						Not Present		Rel-6	RBS-4035
– CHOICE E-RGCH Information						Not Present		Rel-6	RBS-4036
Downlink information for each radio link list			A25b					Rel-8	RBS-4037
– Downlink information for each radio link									RBS-4038
– Choice mode						FDD			RBS-4039
– Primary CPICH info									RBS-4040
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4041
– Serving HS-DSCH radio link indicator						TRUE			RBS-4042
– Serving E-DCH radio link indicator						TRUE		Rel-6	RBS-4043
– Downlink DPCH info for each RL									RBS-4044
– Primary CPICH usage for channel estimation						Primary CPICH may be used			RBS-4045
– DPCH frame offset						Set to value Default DPCH Offset Value (as currently stored in SS) mod 38 400			RBS-4046
– Secondary CPICH info						Not Present			RBS-4047
– DL channelisation code									RBS-4048
– Secondary scrambling code						Not Present			RBS-4049
– Spreading factor						Reference to clause 6.10 Parameter Set			RBS-4050
– Code number						13			RBS-4051
– Scrambling code change						Not Present			RBS-4052
– TPC combination index						0			RBS-4053
– Closed loop timing adjustment mode						Not Present			RBS-4054
– E-AGCH Info								Rel-6	RBS-4055
– E-AGCH Channelisation Code						10			RBS-4056
– CHOICE E-HICH Information								Rel-6	RBS-4057
– Channelisation code						4			RBS-4058
– Signature sequence						1			RBS-4059
– CHOICE E-RGCH Information									RBS-4060
– E-RGCH Information									RBS-4061
– Signature Sequence						0			RBS-4062
– RG combination index						0			RBS-4063
Downlink information for each radio link list			A12, A13, A15, A17f					Rel-6	RBS-4064
			, A19, A19a					Rel-7	RBS-4065
			, A26 , A35 A38, A39, A40, A41, A42, A43, A44, A45					Rel-8 Rel-10 Rel-11	RBS-4066
– Downlink information for each radio link									RBS-4067
– Choice mode						FDD			RBS-4068
– Primary CPICH info									RBS-4069
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4070
– Serving HS-DSCH radio link indicator						TRUE			RBS-4071
– Serving E-DCH radio link indicator						TRUE			RBS-4072
– Downlink DPCH info for each RL									RBS-4073
– Primary CPICH usage for channel estimation						Primary CPICH may be used			RBS-4074
– DPCH frame offset						Set to value Default DPCH Offset Value (as currently stored in SS) mod 38 400			RBS-4075
– Secondary CPICH info						Not Present			RBS-4076
– DL channelisation code									RBS-4077
– Secondary scrambling code						1			RBS-4078
– Spreading factor						Reference to clause 6.10 Parameter Set			RBS-4079
– Code number						0			RBS-4080
– Scrambling code change						Set to value: No code change (if the UE has a compressed mode pattern sequence configured in variable TGPS_IDENTITY or included in the message including IE "Downlink DPCH info for each RL", which is using compressed mode method "SF/2") Set to value: OMIT (otherwise)		Default1 Default2	RBS-4081
– TPC combination index						0			RBS-4082
– Closed loop timing adjustment mode						Not Present			RBS-4083
– E-AGCH Info									RBS-4084
– E-AGCH Channelisation Code						10			RBS-4085
– CHOICE E-HICH Information									RBS-4086
– E-HICH Information									RBS-4087
– Channelisation code						4			RBS-4088
– Signature sequence						1			RBS-4089
– CHOICE E-RGCH Information									RBS-4090
– E-RGCH Information									RBS-4091
– Signature Sequence						0			RBS-4092
– RG combination index						0			RBS-4093
Downlink information for each radio link list			A14, A16 , A19b					Rel-6 Rel-7	RBS-4094
– Downlink information for each radio link									RBS-4095
– Choice mode						FDD			RBS-4096
– Primary CPICH info									RBS-4097
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4098
– Serving HS-DSCH radio link indicator						TRUE			RBS-4099
– Serving E-DCH radio link indicator						TRUE			RBS-4100
– Downlink DPCH info for each RL						Not Present			RBS-4101
– Downlink F-DPCH info for each RL									RBS-4102
– Primary CPICH usage for channel estimation						Primary CPICH may be used			RBS-4103
– F-DPCH frame offset						Set to value Default DPCH Offset Value (as currently stored in SS) mod 38 400			RBS-4104
– F-DPCH slot format						3 if UE supports enhanced F-DPCH, otherwise Not Present		Rel-7	RBS-4105
– Secondary CPICH info						Not Present			RBS-4106
– Secondary scrambling code						Not Present			RBS-4107
– Code number						12			RBS-4108
– TPC combination index						0			RBS-4109
– E-AGCH Info									RBS-4110
– E-AGCH Channelisation Code						10			RBS-4111
– CHOICE E-HICH Information									RBS-4112
– E-HICH Information									RBS-4113
– Channelisation code						4			RBS-4114
– Signature sequence						1			RBS-4115
– CHOICE E-RGCH Information						Not Present			RBS-4116
Downlink information for each radio link list			A17b, A17c, A28a A25c					Rel-7 Rel-9	RBS-4117
– Downlink information for each radio link									RBS-4118
– Choice mode						FDD			RBS-4119
– Primary CPICH info									RBS-4120
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4121
– Serving HS-DSCH radio link indicator						TRUE			RBS-4122
– Serving E-DCH radio link indicator						TRUE			RBS-4123
– Downlink DPCH info for each RL						Not Present			RBS-4124
– Downlink F-DPCH info for each RL									RBS-4125
– Primary CPICH usage for channel estimation						Primary CPICH may be used			RBS-4126
– F-DPCH frame offset						Set to value Default DPCH Offset Value (as currently stored in SS) mod 38 400			RBS-4127
– F-DPCH slot format						3 if UE supports enhanced F-DPCH, otherwise Not Present			RBS-4128
– Secondary CPICH info						Not Present			RBS-4129
– Secondary scrambling code						Not Present			RBS-4130
– Code number						11			RBS-4131
– TPC combination index						0			RBS-4132
– E-AGCH Info									RBS-4133
– E-AGCH Channelisation Code						10			RBS-4134
– CHOICE E-HICH Information									RBS-4135
– E-HICH Information									RBS-4136
– Channelisation code						4			RBS-4137
– Signature sequence						1			RBS-4138
– CHOICE E-RGCH Information						Not Present			RBS-4139
									RBS-4140
Downlink information for each radio link list			A30					Rel-8	RBS-4141
– Downlink information for each radio link									RBS-4142
– Choice mode						FDD			RBS-4143
– Primary CPICH info									RBS-4144
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4145
– Serving HS-DSCH radio link indicator						TRUE			RBS-4146
– Serving E-DCH radio link indicator						TRUE			RBS-4147
– Downlink DPCH info for each RL						Not Present			RBS-4148
– Downlink F-DPCH info for each RL									RBS-4149
– Primary CPICH usage for channel estimation						Primary CPICH may be used			RBS-4150
– F-DPCH frame offset						Set to value Default DPCH Offset Value (as currently stored in SS) mod 38 400			RBS-4151
– F-DPCH slot format						3 if UE supports enhanced F-DPCH, otherwise Not Present			RBS-4152
– Secondary CPICH info						Not Present			RBS-4153
– Secondary scrambling code						Not Present			RBS-4154
– Code number						12			RBS-4155
– TPC combination index						0			RBS-4156
– E-AGCH Info									RBS-4157
– E-AGCH Channelisation Code						11			RBS-4158
– CHOICE E-HICH Information									RBS-4159
– E-HICH Information									RBS-4160
– Channelisation code						4			RBS-4161
– Signature sequence						10			RBS-4162
– CHOICE E-RGCH Information						Not Present			RBS-4163
Downlink information for each radio link list			A20, A21,					Rel-7	RBS-4164
			, A23					Rel-7 Rel-8	RBS-4165
			, A25					Rel-8	RBS-4166
			, A27, A27a					Rel-8	RBS-4167
			, A31 , A34, A36					Rel-9 Rel-10	RBS-4168
– Downlink information for each radio link									RBS-4169
– Choice mode						FDD			RBS-4170
– Primary CPICH info									RBS-4171
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4172
– Serving HS-DSCH radio link indicator						TRUE			RBS-4173
– Serving E-DCH radio link indicator						TRUE			RBS-4174
– Downlink DPCH info for each RL						Not Present			RBS-4175
– Downlink F-DPCH info for each RL									RBS-4176
– Primary CPICH usage for channel estimation						Primary CPICH may be used			RBS-4177
– F-DPCH frame offset						Set to value Default DPCH Offset Value (as currently stored in SS) mod 38 400			RBS-4178
– F-DPCH slot format						3 if UE supports enhanced F-DPCH, otherwise Not Present		Rel-7	RBS-4179
– Secondary CPICH info						Not Present			RBS-4180
– Secondary scrambling code						Not Present			RBS-4181
– Code number						12			RBS-4182
– TPC combination index						0			RBS-4183
– E-AGCH Info									RBS-4184
– E-AGCH Channelisation Code						10			RBS-4185
– CHOICE E-HICH Information									RBS-4186
– E-HICH Information									RBS-4187
– Channelisation code						4			RBS-4188
– Signature sequence						1			RBS-4189
– CHOICE E-RGCH Information									RBS-4190
– E-RGCH Information									RBS-4191
– Signature Sequence						0			RBS-4192
– RG combination index						0			RBS-4193
Downlink information for each radio link list			A22					Rel-7	RBS-4194
– Downlink information for each radio link									RBS-4195
– Choice mode						FDD			RBS-4196
– Primary CPICH info									RBS-4197
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4198
– Serving HS-DSCH radio link indicator						TRUE			RBS-4199
– Serving E-DCH radio link indicator						TRUE			RBS-4200
– Downlink DPCH info for each RL						Not Present			RBS-4201
– Downlink F-DPCH info for each RL									RBS-4202
– Primary CPICH usage for channel estimation						Primary CPICH may be used			RBS-4203
– F-DPCH frame offset						Set to value Default DPCH Offset Value (as currently stored in SS) mod 38 400			RBS-4204
– F-DPCH slot format						3 if UE supports enhanced F-DPCH, otherwise Not Present		Rel-7	RBS-4205
– Secondary CPICH info						Not Present			RBS-4206
– Secondary scrambling code						Not Present			RBS-4207
– Code number						12			RBS-4208
– TPC combination index						0			RBS-4209
– E-AGCH Info									RBS-4210
– E-AGCH Channelisation Code						10			RBS-4211
– CHOICE E-HICH Information									RBS-4212
– E-HICH Information									RBS-4213
– Channelisation code						4			RBS-4214
– Signature sequence						1			RBS-4215
– CHOICE E-RGCH Information									RBS-4216
– E-RGCH Information						Not present			RBS-4217
– Downlink information for each radio link			A32, A33, A37					Rel-10	RBS-4218
– Choice mode						FDD			RBS-4219
– Primary CPICH info									RBS-4220
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4221
– Serving HS-DSCH radio link indicator						TRUE			RBS-4222
– Serving E-DCH radio link indicator						TRUE			RBS-4223
– Downlink DPCH info for each RL						Not Present			RBS-4224
– Downlink F-DPCH info for each RL									RBS-4225
– Primary CPICH usage for channel estimation						Primary CPICH may be used			RBS-4226
– F-DPCH frame offset						Set to value Default DPCH Offset Value (as currently stored in SS) mod 38 400			RBS-4227
– F-DPCH slot format						3 if UE supports enhanced F-DPCH, otherwise Not Present		Rel-7	RBS-4228
– Secondary CPICH info						Not Present			RBS-4229
– Secondary scrambling code						Not Present			RBS-4230
– Code number						11			RBS-4231
– TPC combination index						0			RBS-4232
– E-AGCH Info									RBS-4233
– E-AGCH Channelisation Code						10			RBS-4234
– CHOICE E-HICH Information									RBS-4235
– E-HICH Information									RBS-4236
– Channelisation code						4			RBS-4237
– Signature sequence						1			RBS-4238
– CHOICE E-RGCH Information									RBS-4239
– E-RGCH Information									RBS-4240
– Signature Sequence						0			RBS-4241
– RG combination index						0			RBS-4242
Downlink information for each radio link list			A6, A24			Not Present			RBS-4243
			A29						RBS-4244
Downlink secondary cell info FDD			A25a A25c , A36					Rel-8 Rel-9 Rel-10	RBS-4245
– CHOICE Configuration info						New configuration			RBS-4246
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4247
– Downlink 64QAM configured						Not Present			RBS-4248
– HS-DSCH TB size table						Octet Aligned			RBS-4249
– Primary CPICH info									RBS-4250
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4251
– DL Scrambling Code						Not Present			RBS-4252
– HS-SCCH Channelisation Code Information									RBS-4253
– HS-SCCH Channelisation Code						7			RBS-4254
– Measurement Power Offset						6 dB			RBS-4255
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4256
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4257
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4258
Downlink secondary cell info FDD	A25, A25b							Rel-8	RBS-4259
									RBS-4260
– CHOICE Configuration info						New configuration			RBS-4261
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4262
– Downlink 64QAM configured						Not Present			RBS-4263
– HS-DSCH TB size table						Not Present			RBS-4264
– Primary CPICH info									RBS-4265
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4266
– DL Scrambling Code						Not Present			RBS-4267
– HS-SCCH Channelisation Code Information									RBS-4268
– HS-SCCH Channelisation Code						7			RBS-4269
– Measurement Power Offset						6 dB			RBS-4270
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4271
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4272
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4273
Downlink secondary cell info FDD	A31							Rel-9	RBS-4274
	, A34							Rel-10	RBS-4275
– CHOICE Configuration info						New configuration			RBS-4276
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4277
– Downlink 64QAM configured						Not Present			RBS-4278
– HS-DSCH TB size table						Not Present			RBS-4279
– Primary CPICH info									RBS-4280
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4281
– DL Scrambling Code						Not Present			RBS-4282
– HS-SCCH Channelisation Code Information									RBS-4283
– HS-SCCH Channelisation Code						7			RBS-4284
– Measurement Power Offset						6 dB			RBS-4285
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4286
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4287
-Secondary cell MIMO parameters								Rel-9	RBS-4288
– CHOICE Configuration info									RBS-4289
– Continue									RBS-4290
– New configuration									RBS-4291
– MIMO N_cqi_typeA/M_cqi ratio						1/1			RBS-4292
– MIMO pilot configuration									RBS-4293
-CHOICE Second CPICH pattern									RBS-4294
-Antenna2 P-CPICH						No data			RBS-4295
-Antenna1 S-CPICH									RBS-4296
-Channelisation code						13			RBS-4297
-Power Offset for S-CPICH for MIMO						0			RBS-4298
Downlink secondary cell info FDD	A32 , A33							Rel-9 Rel-10	RBS-4299
– CHOICE Configuration info						New configuration			RBS-4300
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4301
– Downlink 64QAM configured						TRUE			RBS-4302
– HS-DSCH TB size table						Not present			RBS-4303
– Primary CPICH info									RBS-4304
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4305
– DL Scrambling Code						Not Present			RBS-4306
– HS-SCCH Channelisation Code Information									RBS-4307
– HS-SCCH Channelisation Code						6			RBS-4308
– HS-SCCH Channelisation Code						7			RBS-4309
– Measurement Power Offset						6 dB			RBS-4310
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4311
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4312
– Secondary cell MIMO parameters								Rel-9	RBS-4313
– CHOICE Configuration info									RBS-4314
– Continue									RBS-4315
– New configuration									RBS-4316
– MIMO N_cqi_typeA/M_cqi ratio						1/1			RBS-4317
– MIMO pilot configuration									RBS-4318
-CHOICE Second CPICH pattern									RBS-4319
-Antenna2 P-CPICH						No data			RBS-4320
-Antenna1 S-CPICH									RBS-4321
-Channelisation code						29			RBS-4322
Downlink secondary cell info FDD	A35, A37							Rel-10	RBS-4323
– CHOICE Configuration info						New configuration			RBS-4324
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4325
– Downlink 64QAM configured						TRUE			RBS-4326
– HS-DSCH TB size table						Not present			RBS-4327
– Primary CPICH info									RBS-4328
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4329
– DL Scrambling Code						Not Present			RBS-4330
– HS-SCCH Channelisation Code Information									RBS-4331
– HS-SCCH Channelisation Code						6			RBS-4332
– HS-SCCH Channelisation Code						7			RBS-4333
– Measurement Power Offset						6 dB			RBS-4334
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4335
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4336
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4337
Downlink secondary cell info FDD				A38, A39, A40				Rel-11	RBS-4338
– CHOICE Configuration info						New configuration			RBS-4339
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4340
– Downlink 64QAM configured						True			RBS-4341
– HS-DSCH TB size table						Not present			RBS-4342
– Primary CPICH info									RBS-4343
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4344
– DL Scrambling Code						Not Present			RBS-4345
– HS-SCCH Channelisation Code Information									RBS-4346
– HS-SCCH Channelisation Code						6			RBS-4347
– HS-SCCH Channelisation Code						7			RBS-4348
– Measurement Power Offset						6 dB			RBS-4349
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4350
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4351
– multiflowConfigurationInfo								Rel-11	RBS-4352
– Multiflow cell						Intra-NodeB			RBS-4353
– Multiflow time reference cell						False			RBS-4354
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4355
Additional downlink secondary cell info list FDD				A39, A40				Rel-11	RBS-4356
Downlink secondary cell info FDD				A39, A40				Rel-11	RBS-4357
– CHOICE Configuration info						New configuration			RBS-4358
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4359
– Downlink 64QAM configured						True			RBS-4360
– HS-DSCH TB size table						Not present			RBS-4361
– Primary CPICH info									RBS-4362
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4363
– DL Scrambling Code						Not Present			RBS-4364
– HS-SCCH Channelisation Code Information									RBS-4365
– HS-SCCH Channelisation Code						6			RBS-4366
– HS-SCCH Channelisation Code						7			RBS-4367
– Measurement Power Offset						6 dB			RBS-4368
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4369
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4370
– multiflowConfigurationInfo								Rel-11	RBS-4371
– Multiflow cell						Intra-NodeB			RBS-4372
– Multiflow time reference cell						True			RBS-4373
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4374
Downlink secondary cell info FDD				A40				Rel-11	RBS-4375
– CHOICE Configuration info						New configuration			RBS-4376
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4377
– Downlink 64QAM configured						True			RBS-4378
– HS-DSCH TB size table						Not present			RBS-4379
– Primary CPICH info									RBS-4380
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4381
– DL Scrambling Code						Not Present			RBS-4382
– HS-SCCH Channelisation Code Information									RBS-4383
– HS-SCCH Channelisation Code						6			RBS-4384
– HS-SCCH Channelisation Code						7			RBS-4385
– Measurement Power Offset						6 dB			RBS-4386
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4387
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4388
– multiflowConfigurationInfo								Rel-11	RBS-4389
– Multiflow cell						Intra-NodeB			RBS-4390
– Multiflow time reference cell						False			RBS-4391
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4392
Downlink secondary cell info FDD				A41, A42, A43				Rel-11	RBS-4393
– CHOICE Configuration info						New configuration			RBS-4394
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4395
– Downlink 64QAM configured						False			RBS-4396
– HS-DSCH TB size table						Octet Aligned			RBS-4397
– Primary CPICH info									RBS-4398
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4399
– DL Scrambling Code						Not Present			RBS-4400
– HS-SCCH Channelisation Code Information									RBS-4401
– HS-SCCH Channelisation Code						Refer to clause 5.5.1.3			RBS-4402
– Measurement Power Offset						6 dB			RBS-4403
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4404
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4405
– multiflowConfigurationInfo								Rel-11	RBS-4406
– Multiflow cell						Intra-NodeB			RBS-4407
– Multiflow time reference cell						False			RBS-4408
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4409
Additional downlink secondary cell info list FDD				A42, A43				Rel-11	RBS-4410
Downlink secondary cell info FDD				A42, A43				Rel-11	RBS-4411
– CHOICE Configuration info						New configuration			RBS-4412
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4413
– Downlink 64QAM configured						False			RBS-4414
– HS-DSCH TB size table						Octet Aligned			RBS-4415
– Primary CPICH info									RBS-4416
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4417
– DL Scrambling Code						Not Present			RBS-4418
– HS-SCCH Channelisation Code Information									RBS-4419
– HS-SCCH Channelisation Code						Refer to clause 5.5.1.3			RBS-4420
– Measurement Power Offset						6 dB			RBS-4421
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4422
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4423
– multiflowConfigurationInfo								Rel-11	RBS-4424
– Multiflow cell						Intra-NodeB			RBS-4425
– Multiflow time reference cell						True			RBS-4426
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4427
Downlink secondary cell info FDD				A43				Rel-11	RBS-4428
– CHOICE Configuration info						New configuration			RBS-4429
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4430
– Downlink 64QAM configured						False			RBS-4431
– HS-DSCH TB size table						Octet Aligned			RBS-4432
– Primary CPICH info									RBS-4433
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4434
– DL Scrambling Code						Not Present			RBS-4435
– HS-SCCH Channelisation Code Information									RBS-4436
– HS-SCCH Channelisation Code						Refer to clause 5.5.1.3			RBS-4437
– Measurement Power Offset						6 dB			RBS-4438
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4439
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4440
– multiflowConfigurationInfo								Rel-11	RBS-4441
– Multiflow cell						Intra-NodeB			RBS-4442
– Multiflow time reference cell						False			RBS-4443
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4444
Downlink secondary cell info FDD				A44, A45				Rel-11	RBS-4445
– CHOICE Configuration info						New configuration			RBS-4446
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4447
– Downlink 64QAM configured						False			RBS-4448
– HS-DSCH TB size table						Octet Aligned			RBS-4449
– Primary CPICH info									RBS-4450
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4451
– DL Scrambling Code						Not Present			RBS-4452
– HS-SCCH Channelisation Code Information									RBS-4453
– HS-SCCH Channelisation Code						Refer to clause 5.5.1.3			RBS-4454
– Measurement Power Offset						6 dB			RBS-4455
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4456
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4457
– multiflowConfigurationInfo								Rel-11	RBS-4458
– Multiflow cell						Inter-NodeB			RBS-4459
– Multiflow time reference cell						True			RBS-4460
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4461
Additional downlink secondary cell info list FDD				A45				Rel-11	RBS-4462
Downlink secondary cell info FDD				A45				Rel-11	RBS-4463
– CHOICE Configuration info						New configuration			RBS-4464
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4465
– Downlink 64QAM configured						True			RBS-4466
– HS-DSCH TB size table						Not present			RBS-4467
– Primary CPICH info									RBS-4468
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4469
– DL Scrambling Code						Not Present			RBS-4470
– HS-SCCH Channelisation Code Information									RBS-4471
– HS-SCCH Channelisation Code						Refer to clause 5.5.1.3			RBS-4472
– Measurement Power Offset						6 dB			RBS-4473
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4474
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4475
– multiflowConfigurationInfo								Rel-11	RBS-4476
– Multiflow cell						Intra-NodeB			RBS-4477
– Multiflow time reference cell						False			RBS-4478
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4479
Additional downlink secondary cell info list FDD			A33					Rel-10	RBS-4480
Downlink secondary cell info FDD			A33			3rd Carrier (3C and 4C)		Rel-10	RBS-4481
– CHOICE Configuration info						New configuration			RBS-4482
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4483
– Downlink 64QAM configured						TRUE			RBS-4484
– HS-DSCH TB size table						Not present			RBS-4485
– Primary CPICH info									RBS-4486
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4487
– DL Scrambling Code						Not Present			RBS-4488
– HS-SCCH Channelisation Code Information									RBS-4489
– HS-SCCH Channelisation Code						6			RBS-4490
– HS-SCCH Channelisation Code						7			RBS-4491
– Measurement Power Offset						6 dB			RBS-4492
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4493
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4494
– Secondary cell MIMO parameters								Rel-9	RBS-4495
– CHOICE Configuration info									RBS-4496
– Continue									RBS-4497
– New configuration									RBS-4498
– MIMO N_cqi_typeA/M_cqi ratio						1/1			RBS-4499
– MIMO pilot configuration									RBS-4500
-CHOICE Second CPICH pattern									RBS-4501
-Antenna2 P-CPICH						No data			RBS-4502
-Antenna1 S-CPICH									RBS-4503
-Channelisation code						29			RBS-4504
-Power Offset for S-CPICH for MIMO						0			RBS-4505
– Precoding weight set restriction						True			RBS-4506
Downlink secondary cell info FDD			A33			4th Carrier (4C)		Rel-10	RBS-4507
– CHOICE Configuration info						New configuration			RBS-4508
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4509
– Downlink 64QAM configured						TRUE			RBS-4510
– HS-DSCH TB size table						Not present			RBS-4511
– Primary CPICH info									RBS-4512
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4513
– DL Scrambling Code						Not Present			RBS-4514
– HS-SCCH Channelisation Code Information									RBS-4515
– HS-SCCH Channelisation Code						6			RBS-4516
– HS-SCCH Channelisation Code						7			RBS-4517
– Measurement Power Offset						6 dB			RBS-4518
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4519
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4520
– Secondary cell MIMO parameters								Rel-9	RBS-4521
– CHOICE Configuration info									RBS-4522
– Continue									RBS-4523
– New configuration									RBS-4524
– MIMO N_cqi_typeA/M_cqi ratio						1/1			RBS-4525
– MIMO pilot configuration									RBS-4526
-CHOICE Second CPICH pattern									RBS-4527
-Antenna2 P-CPICH						No data			RBS-4528
-Antenna1 S-CPICH									RBS-4529
-Channelisation code						29			RBS-4530
-Power Offset for S-CPICH for MIMO						0			RBS-4531
– Precoding weight set restriction						True			RBS-4532
Additional downlink secondary cell info list FDD			A34			3rd Carrier (3C and 4C)		Rel-10	RBS-4533
Downlink secondary cell info FDD			A34					Rel-10	RBS-4534
– CHOICE Configuration info						New configuration			RBS-4535
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4536
– Downlink 64QAM configured						Not Present			RBS-4537
– HS-DSCH TB size table						Not Present			RBS-4538
– Primary CPICH info									RBS-4539
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4540
– DL Scrambling Code						Not Present			RBS-4541
– HS-SCCH Channelisation Code Information									RBS-4542
– HS-SCCH Channelisation Code						7			RBS-4543
– Measurement Power Offset						6 dB			RBS-4544
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4545
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4546
-Secondary cell MIMO parameters								Rel-9	RBS-4547
– CHOICE Configuration info									RBS-4548
– Continue									RBS-4549
– New configuration									RBS-4550
– MIMO N_cqi_typeA/M_cqi ratio						1/1			RBS-4551
– MIMO pilot configuration									RBS-4552
-CHOICE Second CPICH pattern									RBS-4553
-Antenna2 P-CPICH						No data			RBS-4554
-Antenna1 S-CPICH									RBS-4555
-Channelisation code						13			RBS-4556
-Power Offset for S-CPICH for MIMO						0			RBS-4557
– Precoding weight set restriction						True			RBS-4558
Downlink secondary cell info FDD			A34			4th Carrier (4C)		Rel-10	RBS-4559
– CHOICE Configuration info						New configuration			RBS-4560
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4561
– Downlink 64QAM configured						Not Present			RBS-4562
– HS-DSCH TB size table						Not Present			RBS-4563
– Primary CPICH info									RBS-4564
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4565
– DL Scrambling Code						Not Present			RBS-4566
– HS-SCCH Channelisation Code Information									RBS-4567
– HS-SCCH Channelisation Code						7			RBS-4568
– Measurement Power Offset						6 dB			RBS-4569
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4570
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4571
-Secondary cell MIMO parameters								Rel-9	RBS-4572
– CHOICE Configuration info									RBS-4573
– Continue									RBS-4574
– New configuration									RBS-4575
– MIMO N_cqi_typeA/M_cqi ratio						1/1			RBS-4576
– MIMO pilot configuration									RBS-4577
-CHOICE Second CPICH pattern									RBS-4578
-Antenna2 P-CPICH						No data			RBS-4579
-Antenna1 S-CPICH									RBS-4580
-Channelisation code						13			RBS-4581
-Power Offset for S-CPICH for MIMO						0			RBS-4582
– Precoding weight set restriction						True			RBS-4583
Additional downlink secondary cell info list FDD			A35			3rd Carrier (3C and 4C)		Rel-10	RBS-4584
Downlink secondary cell info FDD			A35					Rel-10	RBS-4585
– CHOICE Configuration info						New configuration			RBS-4586
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4587
– Downlink 64QAM configured						TRUE			RBS-4588
– HS-DSCH TB size table						Not present			RBS-4589
– Primary CPICH info									RBS-4590
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4591
– DL Scrambling Code						Not Present			RBS-4592
– HS-SCCH Channelisation Code Information									RBS-4593
– HS-SCCH Channelisation Code						6			RBS-4594
– HS-SCCH Channelisation Code						7			RBS-4595
– Measurement Power Offset						6 dB			RBS-4596
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4597
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4598
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4599
Downlink secondary cell info FDD			A35			4th Carrier (4C)		Rel-10	RBS-4600
– CHOICE Configuration info						New configuration			RBS-4601
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4602
– Downlink 64QAM configured						TRUE			RBS-4603
– HS-DSCH TB size table						Not present			RBS-4604
– Primary CPICH info									RBS-4605
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4606
– DL Scrambling Code						Not Present			RBS-4607
– HS-SCCH Channelisation Code Information									RBS-4608
– HS-SCCH Channelisation Code						6			RBS-4609
– HS-SCCH Channelisation Code						7			RBS-4610
– Measurement Power Offset						6 dB			RBS-4611
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4612
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4613
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4614
Additional downlink secondary cell info list FDD			A36					Rel-10	RBS-4615
Downlink secondary cell info FDD			A36			3rd Carrier (3C and 4C)		Rel-10	RBS-4616
– CHOICE Configuration info						New configuration			RBS-4617
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4618
– Downlink 64QAM configured						Not Present			RBS-4619
– HS-DSCH TB size table						Octet Aligned			RBS-4620
– Primary CPICH info									RBS-4621
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4622
– DL Scrambling Code						Not Present			RBS-4623
– HS-SCCH Channelisation Code Information									RBS-4624
– HS-SCCH Channelisation Code						7			RBS-4625
– Measurement Power Offset						6 dB			RBS-4626
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4627
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4628
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4629
Downlink secondary cell info FDD			A36			4th Carrier (4C)		Rel-10	RBS-4630
– CHOICE Configuration info						New configuration			RBS-4631
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4632
– Downlink 64QAM configured						Not Present			RBS-4633
– HS-DSCH TB size table						Octet Aligned			RBS-4634
– Primary CPICH info									RBS-4635
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4636
– DL Scrambling Code						Not Present			RBS-4637
– HS-SCCH Channelisation Code Information									RBS-4638
– HS-SCCH Channelisation Code						7			RBS-4639
– Measurement Power Offset						6 dB			RBS-4640
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4641
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4642
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4643
Additional downlink secondary cell info list FDD			A37					Rel-10	RBS-4644
Downlink secondary cell info FDD			A37			3rd Carrier (3C and 4C)		Rel-10	RBS-4645
– CHOICE Configuration info						New configuration			RBS-4646
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4647
– Downlink 64QAM configured						TRUE			RBS-4648
– HS-DSCH TB size table						Not present			RBS-4649
– Primary CPICH info									RBS-4650
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4651
– DL Scrambling Code						Not Present			RBS-4652
– HS-SCCH Channelisation Code Information									RBS-4653
– HS-SCCH Channelisation Code						6			RBS-4654
– HS-SCCH Channelisation Code						7			RBS-4655
– Measurement Power Offset						6 dB			RBS-4656
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4657
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4658
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4659
Downlink secondary cell info FDD			A37			4th Carrier (4C)		Rel-10	RBS-4660
– CHOICE Configuration info						New configuration			RBS-4661
– New H-RNTI						‘1010 1010 1010 1010’			RBS-4662
– Downlink 64QAM configured						TRUE			RBS-4663
– HS-DSCH TB size table						Not present			RBS-4664
– Primary CPICH info									RBS-4665
– Primary scrambling code						Ref. to the Default setting in clause 6.1 (FDD)			RBS-4666
– DL Scrambling Code						Not Present			RBS-4667
– HS-SCCH Channelisation Code Information									RBS-4668
– HS-SCCH Channelisation Code						6			RBS-4669
– HS-SCCH Channelisation Code						7			RBS-4670
– Measurement Power Offset						6 dB			RBS-4671
– UARFCN downlink (Nd)						Reference to clause 5.1 Test frequencies			RBS-4672
– Different Tx diversity mode configuration from serving HS-DSCH cell						Not Present		Rel-8	RBS-4673
-Secondary cell MIMO parameters						Not Present		Rel-9	RBS-4674
MBMS PL Service Restriction Information			A1, A2, A3, A4, A5, A6, A7, A8			Not Present			RBS-4675
			A9, A10					Rel-5	RBS-4676
			, A12, A13, A14, A15, A16					Rel-6	RBS-4677
			, A17, A17a, A17b, A17c, , A17f A18, A19, A19a, A20, A21, A22					Rel-7	RBS-4678
			, A23, A24, A28a					Rel-7 Rel-8	RBS-4679
			, A25, A25a, A26, A27, A27a, A28, A29, A30					Rel-8	RBS-4680
			, A31, A32 , A33, A34, A35, A36, A37 A38, A39, A40, A41, A42, A43, A44, A45					Rel-9 Rel-10 Rel-11	RBS-4681

Condition	Explanation	Version
A1	This IE is needed for "Non speech to CELL_DCH from CELL_DCH in CS"
A2	This IE is needed for "Speech to CELL_DCH from CELL_DCH in CS"
A3	This IE is needed for "Packet to CELL_DCH from CELL_DCH in PS"
A4	This IE is needed for "Packet to CELL_DCH from CELL_FACH in PS"
A5	This IE is needed for "Packet to CELL_FACH from CELL_DCH in PS"
A6	This IE is needed for "Packet to CELL_FACH from CELL_FACH in PS"
A7	This IE is needed for "Non speech to CELL_DCH from CELL_FACH in CS"
A8	This IE is needed for "Speech to CELL_DCH from CELL_FACH in CS"
A9	This IE is needed for "Packet to CELL_DCH / HS-DSCH using three multiplexing options", or when not stated otherwise, for "Packet to CELL_DCH / HS-DSCH from CELL_DCH in PS"	Rel-5
A10	This IE is needed for "Packet to CELL_DCH / HS-DSCH using one multiplexing option", or when not stated otherwise, for "Packet to CELL_DCH / HS-DSCH from CELL_FACH in PS"	Rel-5
A11	This IE is needed for " Packet RAB Setup after Speech RAB Setup in CELL_DCH"
A12	This IE is needed for "Packet to CELL_DCH / E-DCH / HS-DSCH using three multiplexing options (3/3) and SRBs mapped on DCH/DCH"	Rel-6
A13	This IE is needed for "Packet to CELL_DCH / E-DCH / HS-DSCH using one multiplexing option (1/1) and SRBs mapped on E-DCH/DCH"	Rel-6
A14	This IE is needed for "Packet to CELL_DCH / E-DCH / HS-DSCH using one multiplexing option (1/1) and SRBs mapped on E-DCH/HS-DSCH"	Rel-6
A15	This IE is needed for "Packet to CELL_DCH / E-DCH / HS-DSCH with multiple RABs (two streaming/interactive/background) using one multiplexing option (1/1) and SRBs mapped on E-DCH/DCH”	Rel-6
A16	This IE is needed for "Packet to CELL_DCH / E-DCH / HS-DSCH with multiple RABs (one conversational and one streaming/interactive/background) using one multiplexing option (1/1) and SRBs mapped on E-DCH/HS-DSCH”	Rel-6
A17	This IE is needed for "Packet to CELL_DCH / HS-DSCH with enhanced data rate and RLC AM"	Rel-7
A17a	This IE is needed for "Packet to CELL_DCH / HS-DSCH [DL : 64QAM] with enhanced data rate and RLC AM"	Rel-7
A17b	This IE is needed for "Packet to CELL_DCH / HS-DSCH with enhanced data rate and RLC AM using one multiplexing option (1/1) and SRBs mapped on E-DCH/HS-DSCH (MAC-ehs)"	Rel-7
A17c	This IE is needed for "Packet to CELL_DCH / HS-DSCH [DL : 64QAM] with enhanced data rate and RLC AM using one multiplexing option (1/1) and SRBs mapped on E-DCH/HS-DSCH (MAC-ehs)"	Rel-7
A17d	This IE is needed for "Packet to CELL_DCH / HS-DSCH with enhanced data rate and RLC AM using one multiplexing option (1/1) and SRBs mapped on E-DCH/DCH (MAC-ehs)"	Rel-7
A17e	This IE is needed for "Packet to CELL_DCH / HS-DSCH [DL : 64QAM] with enhanced data rate and RLC AM using one multiplexing option (1/1) and SRBs mapped on E-DCH/DCH (MAC-ehs)"	Rel-7
A17f	This IE is needed for "Packet to CELL_DCH / E-DCH / HS-DSCH [DL : 64QAM] with enhanced rate and RLC AM using one multiplexing option (1/1) and SRBs mapped on DCH"	Rel-7
A18	This IE is needed for "Packet to CELL_DCH / HS-DSCH with enhanced data rate and RLC UM"	Rel-7
A19	This IE is needed for "Packet to CELL_DCH / E-DCH[UL : 16QAM] / HS-DSCH using three multiplexing options (3/3) and SRBs mapped on DCH/DCH"	Rel-7
A19a	This IE is needed for "Packet to CELL_DCH / E-DCH[UL : 16QAM] / HS-DSCH using one multiplexing option (1/1) and SRBs mapped on E-DCH/DCH"	Rel-7
A19b	This IE is needed for "Packet to CELL_DCH / E-DCH[UL: 16QAM] / HS-DSCH with multiple RABs (one conversational and one streaming/interactive/background) using one multiplexing option (1/1) and SRBs mapped on E-DCH/HS-DSCH"	Rel-7
A20	This IE is needed for "Packet to CELL_DCH / E-DCH / HS-DSCH with DTX/DRX using one multiplexing option (1/1) and SRBs mapped on E-DCH/HS-DSCH"	Rel-7
A21	This IE is needed for "Packet to CELL_DCH / E-DCH / HS-DSCH with DTX/DRX and multiple RABs (one conversational and one streaming/interactive/background) using one multiplexing option (1/1) and SRBs mapped on E-DCH/HS-DSCH”	Rel-7
A22	This IE is needed for "Packet to CELL_DCH / E-DCH / HS-DSCH with multiple RABs (one conversational and one streaming/interactive/background) with enhanced data rate using one multiplexing option (1/1) and SRBs mapped on E-DCH/HS-DSCH”	Rel-7
A23	This IE is needed for “Speech to CELL_DCH / E-DCH / HS-DSCH CS RAB with DTX/DRX and enhanced data rate using one multiplexing option (1/1) and SRBs mapped on E-DCH/HS-DSCH”	Rel-7 Rel-8 (Note 1)
A24	This IE is needed for “Packet to CELL_FACH from CELL_FACH using one multiplexing option (1/1) and SRBs mapped on RACH/HS-DSCH”	Rel-7
A25	This IE is needed for "Packet to CELL_DCH / E-DCH / HS-DSCH [Dual Carrier Adjacent Channels] with enhanced data rate using one multiplexing option (1/1) and SRBs mapped on E-DCH( MACe/es ) /HS-DSCH”"	Rel-8
A25a	This IE is needed for “Packet to CELL_DCH / HS-DSCH [Dual Carrier Adjacent Channels] with enhanced data rate and RLC AM and SRBs mapped on DCH/DCH”	Rel-8
A25b	This IE is needed for "Packet to CELL_DCH / E-DCH ( MACe/es ) / HS-DSCH [Dual Carrier Adjacent Channels] with enhanced data rate using one multiplexing option (1/1) and SRBs mapped on E-DCH/DCH”	Rel-8
A25c	This IE is needed for "Packet to CELL_DCH / E-DCH ( MACi/is ) [Dual-Cell] / HS-DSCH [Dual Carrier Adjacent Channels] with enhanced data rate using one multiplexing option (1/1) and SRBs mapped on E-DCH/ HS-DSCH”	Rel-9
A26	This IE is needed for "UM Packet to CELL_DCH / E-DCH (MAC-i/is) / HS-DSCH (MAC-ehs) with multiple RABs (three streaming/interactive/background) using one multiplexing option (1/1) and SRBs mapped on E-DCH (MAC-i/is)/DCH”	Rel-8
A27	This IE is needed for "UM Packet to CELL_DCH / E-DCH (MAC-i/is) / HS-DSCH (MAC-ehs) using one multiplexing option (1/1) and SRBs mapped on E-DCH (MAC-i/is)/HS-DSCH (MAC-ehs)"	Rel-8
A27a	This IE is needed for "UM Packet to CELL_DCH / E-DCH [UL : 16QAM] (MAC-i/is) / HS-DSCH (MAC-ehs) using one multiplexing option (1/1) and SRBs mapped on E-DCH (MAC-i/is)/HS-DSCH”	Rel-8
A28	This IE is needed for "Packet to CELL_DCH / HS-DSCH [DL : 64QAM+MIMO] with enhanced data rate and RLC AM"	Rel-8
A28a	This IE is needed for "Packet to CELL_DCH / HS-DSCH [DL : 16QAM+MIMO] with enhanced data rate and RLC AM"	Rel-7
A29	This IE is needed for "AM Packet to Enhanced CELL_FACH from Enhanced CELL_FACH in PS with SRBs mapped on common E-DCH/HS-DSCH"	Rel-8
A30	This IE is needed for “AM Packet to CELL_DCH from Enhanced CELL_FACH in PS with SRBs mapped on E-DCH (MAC-i/is)/HS-DSCH(MAC-ehs)”	Rel-8
A31	This IE is needed for "Packet to CELL_DCH / HS-DSCH [UL: E-DCH DL: DC-HSDPA and MIMO] with enhanced data rate and RLC AM"	Rel-9
A32	This IE is needed for "Packet to CELL_DCH / HS-DSCH [UL: E-DCH DL: 64QAM, DC-HSDPA and MIMO] with enhanced data rate and RLC AM"	Rel-9
A33	This IE is needed for "Packet to CELL_DCH / HS-DSCH [UL: E-DCH DL: 64QAM, 4C-HSDPA and MIMO] with enhanced data rate and RLC AM and SRBs mapped on E-DCH (MAC-i/is)/HS-DSCH (MAC-ehs)"	Rel-10
A34	This IE is needed for "Packet to CELL_DCH / HS-DSCH [UL: E-DCH DL: 16QAM, 4C-HSDPA and MIMO] with enhanced data rate and RLC AM and SRBs mapped on E-DCH (MAC-i/is)/HS-DSCH (MAC-ehs)"	Rel-10
A35	This IE is needed for "Packet to CELL_DCH / HS-DSCH [UL: E-DCH DL: 64QAM, 4C-HSDPA] with enhanced data rate and RLC AM and SRBs mapped on DCH/DCH "	Rel-10
A36	This IE is needed for "Packet to CELL_DCH / HS-DSCH [UL: E-DCH DL: 16QAM, 4C-HSDPA] with enhanced data rate and RLC AM and SRBs mapped on E-DCH (MAC-i/is)/HS-DSCH (MAC-ehs)"	Rel-10
A37	This IE is needed for "Packet to CELL_DCH / HS-DSCH [UL: E-DCH DL: 64QAM, 4C-HSDPA] with enhanced data rate and RLC AM and SRBs mapped on E-DCH (MAC-i/is)/HS-DSCH (MAC-ehs)"	Rel-10
A38	This IE is needed for "Packet to CELL_DCH / HS-DSCH [UL: E-DCH DL: 64QAM, SF-2C-HSDPA] with enhanced data rate and RLC AM and SRBs mapped on DCH/DCH "	Rel-11
A39	This IE is needed for "Packet to CELL_DCH / HS-DSCH [UL: E-DCH DL: 64QAM, DF-3C-HSDPA] with enhanced data rate and RLC AM and SRBs mapped on DCH/DCH "	Rel-11
A40	This IE is needed for "Packet to CELL_DCH / HS-DSCH [UL: E-DCH DL: 64QAM, DF-4C-HSDPA] with enhanced data rate and RLC AM and SRBs mapped on DCH/DCH "	Rel-11
A41	This IE is needed for "Packet to CELL_DCH / HS-DSCH [UL: E-DCH DL: 16QAM, SF-2C-HSDPA] with enhanced data rate and RLC AM and SRBs mapped on DCH/DCH "	Rel-11
A42	This IE is needed for "Packet to CELL_DCH / HS-DSCH [UL: E-DCH DL: 16QAM, DF-3C-HSDPA] with enhanced data rate and RLC AM and SRBs mapped on DCH/DCH "	Rel-11
A43	This IE is needed for "Packet to CELL_DCH / HS-DSCH [UL: E-DCH DL: 16QAM, DF-4C-HSDPA] with enhanced data rate and RLC AM and SRBs mapped on DCH/DCH "	Rel-11
A44	This IE is needed for "Packet to CELL_DCH / HS-DSCH [UL: E-DCH DL: 16QAM/64QAM, SF-2C-HSDPA and Inter-Node B] with enhanced data rate and RLC AM and SRBs mapped on DCH/DCH "	Rel-11
A45	This IE is needed for "Packet to CELL_DCH / HS-DSCH [UL: E-DCH DL: 16QAM/64QAM, DF-3C-HSDPA and Inter-Node B] with enhanced data rate and RLC AM and SRBs mapped on DCH/DCH "	Rel-11

NOTE 1: Support depends on the UE capability: Support for CS voice over HSPA. This is supported in Rel-8 and may be supported in Rel-7.

Condition	Explanation	Version
MAC-I-FIXED	Used with other condition when MAC-i/is with Fixed RLC PDU size is configured	Rel-8
MAC-I-FLEX	Used with other condition when MAC-i/is with Flexible RLC PDU size is configured	Rel-8

Contents of RADIO BEARER SETUP message: AM or UM, for MBMS PtP Radio Bearer Setup

Information Element	Condition	Value/remark
– RAB information for setup
– RAB info		(UM DTCH for PS domain DL only)
– RAB identity		11111111B For Selected Service and Set to same as Enhanced NSAPI received in Service Request (10000000B to 11111110B) for Multicast service. The first/ leftmost bit of the bit string contains the most significant bit of the RAB identity.
– CN domain identity		PS domain
– NAS Synchronization Indicator		Not Present
– Re-establishment timer		useT315
– RB information to setup
– RB identity		21
– MBMS Service Identity		Present for Selected Service only
– MBMS Service ID		MBMS Service ID of the service UE has selected
– MBMS Session identity
– MBMS Session ID		Ongoing Session ID
– PDCP info
– Support for lossless SRNS relocation		FALSE
– Max PDCP SN window size		Not present
– PDCP PDU header		Absent
– Header compression information		Not present
– CHOICE RLC info type		RLC info
– CHOICE Uplink RLC mode		Not Present
– CHOICE Downlink RLC mode		UM RLC
– DL UM RLC LI size		7
– DL Reception Window Size		Not Present
– RB mapping info
– Information for each multiplexing option		1 RBMuxOptions
– RLC logical channel mapping indicator		Not Present
– Number of uplink RLC logical channels		Not Present
– Downlink RLC logical channel info
– Number of downlink RLC logical channels		1
– Downlink transport channel type		DCH
– DL DCH Transport channel identity		7
– DL DSCH Transport channel identity		Not Present
– Logical channel identity		Not Present
Added or Reconfigured UL TrCH information	B5, B2	5 DCH reconfigured
– Uplink transport channel type		DCH
– UL Transport channel identity		5
– TFS
– CHOICE Transport channel type		Dedicated transport channels
– Dynamic Transport format information
– RLC Size		Reference to clause 6. 11.1b Parameter Set
– Number of TBs and TTI List		(This IE is repeated for TFI number.)
– Transmission Time Interval		Not Present
– Number of Transport blocks		Reference to clause 6. 11.1b Parameter Set
– CHOICE Logical channel list		All
– Semi-static Transport Format information
– Transmission time interval		Reference to clause 6. 11.1b Parameter Set
– Type of channel coding		Reference to clause 6. 11.1b Parameter Set
– Coding Rate		Reference to clause 6. 11.1b Parameter Set
– Rate matching attribute		Reference to clause 6. 11.1b Parameter Set
– CRC size		Reference to clause 6. 11.1b Parameter Set
Added or Reconfigured DL TrCH information	B1, B2	2 TrCHs(DCH for DCCH and 1 DCH for DTCH)
– Downlink transport channel type		DCH
– DL Transport channel identity		10
– CHOICE DL parameters		Same as UL
– Uplink transport channel type		DCH
– UL TrCH identity		5
– DCH quality target
– BLER Quality value		-20 (-2.0)
– Downlink transport channel type		DCH
– DL Transport channel identity		7
– CHOICE DL parameters		Explicit
– TFS
– CHOICE Transport channel type		Dedicated transport channel
– Dynamic transport format information
– RLC Size		Reference to clause 6. 11.1b Parameter Set
– Number of TBs and TTI List		(This IE is repeated for TFI number.)
– Transmission Time Interval		Not Present
– Number of Transport blocks		Reference to clause 6. 11.1b Parameter Set only including TF0
– CHOICE Logical channel list		All
– Semi-static Transport Format information
– Transmission time interval		Reference to clause 6. 11.1b Parameter Set
– Type of channel coding		Reference to clause 6. 11.1b Parameter Set
– Coding Rate		Reference to clause 6. 11.1b Parameter Set
– Rate matching attribute		Reference to clause 6. 11.1b Parameter Set
– CRC size		Reference to clause 6. 11.1b Parameter Set
– DCH quality target
– BLER Quality value		-20 (-2.0)
Added or Reconfigured DL TrCH information	B3, B4	3 TrCHs(DCH for DCCH and 2 DCH for DTCH’s)
– Downlink transport channel type		DCH
– DL Transport channel identity		10
– CHOICE DL parameters		Same as UL
– Uplink transport channel type		DCH
– UL TrCH identity		5
– DCH quality target
– BLER Quality value		-20 (-2.0)
– Downlink transport channel type		DCH
– DL Transport channel identity		6
– CHOICE DL parameters		Same as UL
– Uplink transport channel type		DCH
– UL TrCH identity		1
– DCH quality target
– BLER Quality value		-20 (-2.0)
– Downlink transport channel type		DCH
– DL Transport channel identity		7
– CHOICE DL parameters		Explicit
– TFS
– CHOICE Transport channel type		Dedicated transport channel
– Dynamic transport format information
– RLC Size		Reference to clause 6. 11.1a Parameter Set
– Number of TBs and TTI List		(This IE is repeated for TFI number.)
– Transmission Time Interval		Not Present
– Number of Transport blocks		Reference to clause 6. 11.1a Parameter
– CHOICE Logical channel list		All
– Semi-static Transport Format information
– Transmission time interval		Reference to clause 6. 11.1a Parameter Set
– Type of channel coding		Reference to clause 6. 11.1a Parameter Set
– Coding Rate		Reference to clause 6. 11.1a Parameter Set
– Rate matching attribute		Reference to clause 6. 11.1a Parameter Set
– CRC size		Reference to clause 6. 11.1a Parameter Set
– DCH quality target
– BLER Quality value		-20 (-2.0)
All other IEs	B1	Use the values defined in the RADIO BEARER SETUP message indicated as “Packet to CELL_DCH from CELL_DCH in PS” condition A3 except RB parameter set referred in 6.11.1b instead of 6.10
All other IEs	B2	Use the values defined in the RADIO BEARER SETUP message indicated as “Packet to CELL_DCH from CELL_FACH in PS” condition A4 except RB parameter set referred in 6.11.1b instead of 6.10
All other IEs	B3	Use the values defined in the RADIO BEARER SETUP message indicated as “Packet to CELL_DCH from CELL_DCH in PS” condition A3 except RB parameter set referred in 6.11.1a instead of 6.10
All other IEs	B4	Use the values defined in the RADIO BEARER SETUP message indicated as “Packet to CELL_DCH from CELL_FACH in PS” condition A4 except RB parameter set referred in 6.11.1a instead of 6.10

Condition	Explanation	Version
B1	This IE is needed for " MBMS PtP Radio Bearer Setup when UE state is state 6-7"
B2	This IE is needed for " MBMS PtP Radio Bearer Setup when UE state is state 6-8"
B3	This IE is needed for " MBMS PtP Radio Bearer Setup, when UE state is 6-10"
B4	This IE is needed for " MBMS PtP Radio Bearer Setup, when UE state is 6-11"

Contents of RADIO BEARER SETUP COMPLETE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if the value is identical to the same IE in the downlink RADIO BEARER SETUP message.
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Uplink integrity protection activation info	Not checked.
CHOICE mode	FDD
START	Not checked (if ciphering is OFF), check the presence if ciphering is ON.
Deferred measurement control reading	Not present for Rel-7 or later, otherwise Not checked
COUNT-C activation time	The UE shall include this IE if the following two conditions are fulfilled: (a) The RADIO BEARER SETUP message did not contain the IE "Ciphering activation time for DPCH" and (b) The RADIO BEARER SETUP message established the first RB(s) mapped to RLC-TM for a CN domain. Else, this IE is absent.
Radio bearer uplink ciphering activation time info	Not checked
Uplink counter synchronization info	Not present

Contents of RADIO BEARER SETUP FAILURE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if it is set to identical value of the same IE in the downlink RADIO BEARER SETUP message.
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Failure cause	Checked to see if it meets test requirement
Radio bearers for which reconfiguration would have succeeded	Not checked

Contents of RADIO BEARER RECONFIGURATION message: AM or UM

Information Element	Condition		Value/remark		Version		Index
Message Type	A1,A2,A3,A4,A5,A6						RBC-001
RRC transaction identifier			Arbitrarily selects an integer between 0 and 3				RBC-002
Integrity check info							RBC-003
– message authentication code			SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.				RBC-004
– RRC message sequence number			SS provides the value of this IE, from its internal counter.				RBC-005
Integrity protection mode info			Not Present				RBC-006
Ciphering mode info			Not Present				RBC-007
Activation time	A1,A2,A3		(256+CFN-(CFN MOD 8 + 8))MOD 256				RBC-008
Activation time	A4, A5,A6		Not Present				RBC-009
Delay restriction flag	A1,A2,A3,A4,A5,A6		Not Present		Rel-6		RBC-010
New U-RNTI			Not Present				RBC-011
New C-RNTI	A1, A2, A3, A4,		Not Present				RBC-012
New C-RNTI	A5, A6		‘1010 1010 1010 1010’				RBC-013
New DSCH-RNTI	A1, A2, A3, A4, A5, A6		Not Present		R99 and Rel-4 only		RBC-014
New H-RNTI	A1, A2, A3, A4, A5, A6		Not Present		Rel-5		RBC-015
New Primary E-RNTI			Not Present		Rel-6		RBC-016
New Secondary E-RNTI			Not Present		Rel-6		RBC-017
RRC State indicator	A1, A2, A3, A4		CELL_DCH				RBC-018
RRC State indicator	A5, A6		CELL_FACH				RBC-019
UE Mobility State Indicator			Not Present		Rel-7		RBC-020
UTRAN DRX cycle length coefficient	A1,A2,A3,A4,A5,A6		Not Present				RBC-021
CN information info			Not Present				RBC-022
URA identity			Not Present				RBC-023
CHOICE specification mode			Complete specification		Rel-5		RBC-024
RNC support for change of UE capability			Not Present		Rel-7		RBC-025
Reconfiguration in response to requested change of UE capability			Not Present		Rel-7		RBC-026
RAB information to reconfigure list			Not Present				RBC-027
RB information to reconfigure list	A1		TS25.331 specifies that "Although this IE is not always required, need is MP to align with ASN.1".				RBC-028
– RB information to reconfigure			(UM DCCH for RRC)				RBC-029
– RB identity			1				RBC-030
– PDCP info			Not Present				RBC-031
– PDCP SN info			Not Present				RBC-032
– RLC info			Not Present				RBC-033
– RB mapping info			Not Present				RBC-034
– RB stop/continue			Not Present				RBC-035
– RB information to reconfigure			(AM DCCH for RRC)				RBC-036
– RB identity			2				RBC-037
– PDCP info			Not Present				RBC-038
– PDCP SN info			Not Present				RBC-039
– RLC info			Not Present				RBC-040
– RB mapping info			Not Present				RBC-041
– RB stop/continue			Not Present				RBC-042
– RB information to reconfigure			(AM DCCH for NAS_DT High priority)				RBC-043
– RB identity			3				RBC-044
– PDCP info			Not Present				RBC-045
– PDCP SN info			Not Present				RBC-046
– RLC info			Not Present				RBC-047
– RB mapping info			Not Present				RBC-048
– RB stop/continue			Not Present				RBC-049
– RB information to reconfigure			(AM DCCH for NAS_DT Low priority)				RBC-050
– RB identity			4				RBC-051
– PDCP info			Not Present				RBC-052
– PDCP SN info			Not Present				RBC-053
– RLC info			Not Present				RBC-054
– RB mapping info			Not Present				RBC-055
– RB stop/continue			Not Present				RBC-056
– RB information to reconfigure			(TM DTCH)				RBC-057
– RB identity			10				RBC-058
– PDCP info			Not Present				RBC-059
– PDCP SN info			Not Present				RBC-060
– RLC info			Not Present				RBC-061
– RB mapping info			Not Present				RBC-062
– RB stop/continue			Not Present				RBC-063
RB information to reconfigure list	A2		TS25.331 specifies that "Although this IE is not always required, need is MP to align with ASN.1".				RBC-064
– RB information to reconfigure			(UM DCCH for RRC)				RBC-065
– RB identity			1				RBC-066
– PDCP info			Not Present				RBC-067
– PDCP SN info			Not Present				RBC-068
– RLC info			Not Present				RBC-069
– RB mapping info			Not Present				RBC-070
– RB stop/continue			Not Present				RBC-071
– RB information to reconfigure			(AM DCCH for RRC)				RBC-072
– RB identity			2				RBC-073
– PDCP info			Not Present				RBC-074
– PDCP SN info			Not Present				RBC-075
– RLC info			Not Present				RBC-076
– RB mapping info			Not Present				RBC-077
– RB stop/continue			Not Present				RBC-078
– RB information to reconfigure			(AM DCCH for NAS_DT High priority)				RBC-079
– RB identity			3				RBC-080
– PDCP info			Not Present				RBC-081
– PDCP SN info			Not Present				RBC-082
– RLC info			Not Present				RBC-083
– RB mapping info			Not Present				RBC-084
– RB stop/continue			Not Present				RBC-085
– RB information to reconfigure			(AM DCCH for NAS_DT Low priority)				RBC-086
– RB identity			4				RBC-087
– PDCP info			Not Present				RBC-088
– PDCP SN info			Not Present				RBC-089
– RLC info			Not Present				RBC-090
– RB mapping info			Not Present				RBC-091
– RB stop/continue			Not Present				RBC-092
– RB information to reconfigure			(TM DTCH)				RBC-093
– RB identity			10				RBC-094
– PDCP info			Not Present				RBC-095
– PDCP SN info			Not Present				RBC-096
– RLC info			Not Present				RBC-097
– RB mapping info			Not Present				RBC-098
– RB stop/continue			Not Present				RBC-099
– RB information to reconfigure			(TM DTCH)				RBC-100
– RB identity			11				RBC-101
– PDCP info			Not Present				RBC-102
– PDCP SN info			Not Present				RBC-103
– RLC info			Not Present				RBC-104
– RB mapping info			Not Present				RBC-105
– RB stop/continue			Not Present				RBC-106
– RB information to reconfigure			(TM DTCH) (This IE is needed for 12.2 kbps and 10.2 kbps)				RBC-107
– RB identity			12				RBC-108
– PDCP info			Not Present				RBC-109
– PDCP SN info			Not Present				RBC-110
– RLC info			Not Present				RBC-111
– RB mapping info			Not Present				RBC-112
– RB stop/continue			Not Present				RBC-113
RB information to reconfigure list	A3,A4,A5,A6		TS25.331 specifies that "Although this IE is not always required, need is MP to align with ASN.1".				RBC-114
– RB information to reconfigure			(UM DCCH for RRC)				RBC-115
– RB identity			1				RBC-116
– PDCP info			Not Present				RBC-117
– PDCP SN info			Not Present				RBC-118
– RLC info			Not Present				RBC-119
– RB mapping info			Not Present				RBC-120
– RB stop/continue			Not Present				RBC-121
– RB information to reconfigure			(AM DCCH for RRC)				RBC-122
– RB identity			2				RBC-123
– PDCP info			Not Present				RBC-124
– PDCP SN info			Not Present				RBC-125
– RLC info			Not Present				RBC-126
– RB mapping info			Not Present				RBC-127
– RB stop/continue			Not Present				RBC-128
– RB information to reconfigure			(AM DCCH for NAS_DT High priority)				RBC-129
– RB identity			3				RBC-130
– PDCP info			Not Present				RBC-131
– PDCP SN info			Not Present				RBC-132
– RLC info			Not Present				RBC-133
– RB mapping info			Not Present				RBC-134
– RB stop/continue			Not Present				RBC-135
– RB information to reconfigure			(AM DCCH for NAS_DT Low priority)				RBC-136
– RB identity			4				RBC-137
– PDCP info			Not Present				RBC-138
– PDCP SN info			Not Present				RBC-139
– RLC info			Not Present				RBC-140
– RB mapping info			Not Present				RBC-141
– RB stop/continue			Not Present				RBC-142
– RB information to reconfigure			(AM DTCH)				RBC-143
– RB identity			20				RBC-144
– PDCP info			Not Present				RBC-145
– PDCP SN info			Not Present				RBC-146
– RLC info			Not Present				RBC-147
– RB mapping info			Not Present				RBC-148
– RB stop/continue			Not Present				RBC-149
RB information to be affected	A1, A2, A3,A4,A5,A6		Not Present				RBC-150
RB with PDCP context relocation info list			Not Present		Rel-5		RBC-151
PDCP ROHC target mode			Not Present		Rel-5		RBC-152
UL Transport channel information common for all transport channels	A1, A2, A5,A6		Not Present				RBC-153
UL Transport channel information common for all transport channels	A3, A4						RBC-154
– PRACH TFCS			Not Present				RBC-155
– CHOICE mode			FDD				RBC-156
– TFC subset			Not Present				RBC-157
– UL DCH TFCS							RBC-158
– CHOICE TFCI signalling			Normal				RBC-159
– TFCI Field 1 information							RBC-160
– CHOICE TFCS representation			Complete reconfiguration				RBC-161
– TFCS complete reconfigure information							RBC-162
– CHOICE CTFC Size			Number of bits used must be enough to cover all combinations of CTFC from clause 6.10.2.4 Parameter Set.				RBC-163
– CTFC information			This IE is repeated for TFC numbers and reference to clause 6.10.2.4 Parameter Set				RBC-164
– CTFC			Reference to clause 6.10.2.4 Parameter Set				RBC-165
– Power offset information							RBC-166
– CHOICE Gain Factors			Computed Gain Factors(The last TFC is set to Signalled Gain Factors)				RBC-167
– Gain factor βc			11 (below 64 kbps) 9 (equal or higher than 64 kbps) when HSDPA is not configured 9 (equal or higher than 64 kbps and below 384 kbps) when HSDPA is also configured 6 (equal or higher than 384 kbps) when HSDPA is also configured (Not Present if the CHOICE Gain Factors is set to ComputedGain Factors)				RBC-168
– Gain factor βd			15 (Not Present if the CHOICE Gain Factors is set to ComputedGain Factors)				RBC-169
– Reference TFC ID			0				RBC-170
– CHOICE mode			FDD				RBC-171
– Power offset P p-m			Not Present				RBC-172
Deleted UL TrCH information	A1, A2, A3, A4, A5,A6		Not Present				RBC-173
Added or Reconfigured UL TrCH information	A1, A2, A5,A6		Not Present				RBC-174
Added or Reconfigured UL TrCH information	A4		2 TrCHs(DCH for DCCH and DCH for DTCH)					RBC-175
– Uplink transport channel type			DCH					RBC-176
– UL Transport channel identity			5					RBC-177
– TFS								RBC-178
– CHOICE Transport channel type			Dedicated transport channels					RBC-179
– Dynamic Transport format information								RBC-180
– RLC Size			Reference to clause 6.10 Parameter Set					RBC-181
– Number of TBs and TTI List			(This IE is repeated for TFI number.)					RBC-182
– Transmission Time Interval			Not Present					RBC-183
– Number of Transport blocks			Reference to clause 6.10 Parameter Set					RBC-184
– CHOICE Logical channel list			All					RBC-185
– Semi-static Transport Format information								RBC-186
– Transmission time interval			Reference to clause 6.10 Parameter Set					RBC-187
– Type of channel coding			Reference to clause 6.10 Parameter Set					RBC-188
– Coding Rate			Reference to clause 6.10 Parameter Set					RBC-189
– Rate matching attribute			Reference to clause 6.10 Parameter Set					RBC-190
– CRC size			Reference to clause 6.10 Parameter Set					RBC-191
– Uplink transport channel type			DCH					RBC-192
– UL Transport channel identity			1					RBC-193
– TFS								RBC-194
– CHOICE Transport channel type			Dedicated transport channels					RBC-195
– Dynamic Transport format information								RBC-196
– RLC Size			Reference to clause 6.10 Parameter Set					RBC-197
– Number of TBs and TTI List			(This IE is repeated for TFI number.)					RBC-198
– Transmission Time Interval			Not Present					RBC-199
– Number of Transport blocks			Reference to clause 6.10 Parameter Set					RBC-200
– CHOICE Logical channel list			All					RBC-201
– Semi-static Transport Format information								RBC-202
– Transmission time interval			Reference to clause 6.10 Parameter Set					RBC-203
– Type of channel coding			Reference to clause 6.10 Parameter Set					RBC-204
– Coding Rate			Reference to clause 6.10 Parameter Set					RBC-205
– Rate matching attribute			Reference to clause 6.10 Parameter Set					RBC-206
– CRC size			Reference to clause 6.10 Parameter Set					RBC-207
Added or Reconfigured UL TrCH information	A3		(DCH for DTCH)				RBC-208
– Uplink transport channel type			DCH				RBC-209
– UL Transport channel identity			1				RBC-210
– TFS							RBC-211
– CHOICE Transport channel type			Dedicated transport channels				RBC-212
– Dynamic Transport format information							RBC-213
– RLC Size			Reference to clause 6.10 Parameter Set				RBC-214
– Number of TBs and TTI List			(This IE is repeated for TFI number.)				RBC-215
– Transmission Time Interval			Not Present				RBC-216
– Number of Transport blocks			Reference to clause 6.10 Parameter Set				RBC-217
– CHOICE Logical channel list			All				RBC-218
– Semi-static Transport Format information							RBC-219
– Transmission time interval			Reference to clause 6.10 Parameter Set				RBC-220
– Type of channel coding			Reference to clause 6.10 Parameter Set				RBC-221
– Coding Rate			Reference to clause 6.10 Parameter Set				RBC-222
– Rate matching attribute			Reference to clause 6.10 Parameter Set				RBC-223
– CRC size			Reference to clause 6.10 Parameter Set				RBC-224
CHOICE mode	A1,A2,A3,A4,A5,A6		Not Present				RBC-225
DL Transport channel information common for all transport channel	A1, A2, A5, A6		Not Present				RBC-226
DL Transport channel information common for all transport channel	A3,A4							RBC-227
– SCCPCH TFCS			Not Present					RBC-228
– CHOICE mode			FDD					RBC-229
– CHOICE DL parameters			Explicit					RBC-230
– DL DCH TFCS								RBC-231
– CHOICE TFCI Signalling			Normal					RBC-232
– TFCI Field 1 Information								RBC-233
– CHOICE TFCS representation			Complete reconfiguration					RBC-234
– TFCS complete reconfigure								RBC-235
– CHOICE CTFC Size			Number of bits used must be enough to cover all combinations of CTFC from clause 6.10.2.4 Parameter Set.					RBC-236
– CTFC information			This IE is repeated for TFC numbers and reference to clause 6.10.2.4					RBC-237
– CTFC			Reference to clause 6.10.2.4 Parameter Set					RBC-238
– Power offset information			Not Present					RBC-239
Deleted DL TrCH information	A1, A2, A3, A4, A5,A6		Not Present				RBC-240
Added or Reconfigured DL TrCH information	A1, A2, A5, A6		Not Present				RBC-241
Added or Reconfigured DL TrCH information	A4		2 TrCHs(DCH for DCCH and DCH for DTCH)				RBC-242
– Downlink transport channel type			DCH				RBC-243
– DL Transport channel identity			10				RBC-244
– CHOICE DL parameters			Same as UL				RBC-245
– Uplink transport channel type			DCH				RBC-246
– UL TrCH identity			5				RBC-247
– DCH quality target							RBC-248
– BLER Quality value			Not Present				RBC-249
– Downlink transport channel type			DCH				RBC-250
– DL Transport channel identity			6				RBC-251
– CHOICE DL parameters			Explicit				RBC-252
– TFS							RBC-253
– CHOICE Transport channel type			Dedicated transport channel				RBC-254
– Dynamic transport format information							RBC-255
– RLC Size			Reference to clause 6.10 Parameter Set				RBC-256
– Number of TBs and TTI List			(This IE is repeated for TFI number.)				RBC-257
– Dynamic transport format information							RBC-258
– Transmission Time Interval			Not Present				RBC-259
– Number of Transport blocks			Reference to clause 6.10 Parameter Set				RBC-260
– Semi-static Transport Format information							RBC-261
– Transmission time interval			Reference to clause 6.10 Parameter Set				RBC-262
– Type of channel coding			Reference to clause 6.10 Parameter Set				RBC-263
– Coding Rate			Reference to clause 6.10 Parameter Set				RBC-264
– Rate matching attribute			Reference to clause 6.10 Parameter Set				RBC-265
– CRC size			Reference to clause 6.10 Parameter Set				RBC-266
– DCH quality target							RBC-267
– BLER Quality value			-20 (-2.0)				RBC-268
Added or Reconfigured DL TrCH information	A3						RBC-269
– Downlink transport channel type			DCH				RBC-270
– DL Transport channel identity			6				RBC-271
– CHOICE DL parameters			Explicit				RBC-272
– TFS							RBC-273
– CHOICE Transport channel type			Dedicated transport channel				RBC-274
– Dynamic transport format information							RBC-275
– RLC Size			Reference to clause 6.10 Parameter Set				RBC-276
– Number of TBs and TTI List			(This IE is repeated for TFI number.)				RBC-277
– Dynamic transport format information							RBC-278
– Transmission Time Interval			Not Present				RBC-279
– Number of Transport blocks			Reference to clause 6.10 Parameter Set				RBC-280
– Semi-static Transport Format information							RBC-281
– Transmission time interval			Reference to clause 6.10 Parameter Set				RBC-282
– Type of channel coding			Reference to clause 6.10 Parameter Set				RBC-283
– Coding Rate			Reference to clause 6.10 Parameter Set				RBC-284
– Rate matching attribute			Reference to clause 6.10 Parameter Set				RBC-285
– CRC size			Reference to clause 6.10 Parameter Set				RBC-286
– DCH quality target							RBC-287
– BLER Quality value			-20 (-2.0)				RBC-288
Preconfiguration	A5		Not Present		Rel-5			RBC-289
CHOICE Mode			FDD					RBC-290
– predefinedConfiguration Identity			Not Present					RBC-291
– defaultConfig			Not Present					RBC-292
Frequency info	A1,A2,A3,A4,A5						RBC-293
– UARFCN uplink (Nu)			Not present Absence of this IE is equivalent to applying the default duplex distance defined for the operating frequency according to 3GPP TS 25.101 [11]				RBC-294
– UARFCN downlink (Nd)			Reference to clause 5.1 Test frequencies				RBC-295
Frequency info	A6		Not Present				RBC-296
DTX-DRX timing information			Not Present		Rel-7		RBC-297
DTX-DRX Information			Not Present		Rel-7		RBC-298
HS-SCCH less Information			Not Present		Rel-7		RBC-299
MIMO parameters			Not Present		Rel-7		RBC-300
CHOICE mode	A5		Not Present		Rel-8			RBC-301
– MIMO N_cqi_typeA/M_cqi ratio			Not Present		Rel-7			RBC-302
– MIMO pilot configuration			Not Present		Rel-7			RBC-303
– Precoding weight set restriction			Not Present		Rel-7			RBC-304
MIMO mode with four transmit antennas parameters			Not Present		Rel-11			RBC-304a
DCH Enhancements info FDD			Not Present		Rel-12			RBC-304b
Maximum allowed UL TX power	A1,A2,A3,A4,A5,A6		33dBm				RBC-305
CHOICE channel requirement	A1, A2, A3, A4		Uplink DPCH info				RBC-306
-Uplink DPCH power control info							RBC-307
– DPCCH power offset			-40 (-80dB)				RBC-308
– PC Preamble			1 frame				RBC-309
– SRB delay			7 frames				RBC-310
– Power Control Algorithm			Algorithm1				RBC-311
– TPC step size			0 (1dB)				RBC-312
– ACK			Not Present		Rel-5		RBC-313
– NACK			Not Present		Rel-5		RBC-314
– Ack-Nack repetition factor			Not Present		Rel-5		RBC-315
– Scrambling code type			Long				RBC-316
– Scrambling code number			0 (0 to 16777215)				RBC-317
– Number of DPDCH			Not Present(1)				RBC-318
– spreading factor			Reference to clause 6.10 Parameter Set				RBC-319
– TFCI existence			Reference to clause 6.10 Parameter Set				RBC-320
– Number of FBI bit			Reference to clause 6.10 Parameter Set				RBC-321
– Number of TPC bits			Not Present		Rel-7		RBC-322
– Puncturing Limit			Reference to clause 6.10 Parameter Set				RBC-323
CHOICE channel requirement	A5, A6		Not Present				RBC-324
E-DCH Info			Not Present		Rel-6		RBC-325
Mac-es-e-resetIndicator	A5		Not Present		Rel-6			RBC-326
CHOICE modeSpecificInfo	A5		FDD					RBC-327
– e-DPCCH-Info	A5		Not Present					RBC-328
– schedulingTransmConfiguration	A5		Not Present					RBC-329
– ul-16QAM-Settings	A5		Not Present		Rel-7			RBC-330
CHOICE Mode	A1,A2,A3,A4,A5,A6		FDD				RBC-331
– Downlink PDSCH information			Not Present		R99 and Rel-4 only		RBC-332
Uplink secondary cell info FDD	A5				Rel-9			RBC-333
Uplink CLTD info FDD				Not Present		Rel-11			RBC-333a
Uplink OLTD info FDD				Not Present		Rel-11			RBC-333b
Downlink HS-PDSCH Information	A1, A2, A3, A4, A5, A6		Not Present		Rel-5		RBC-334
– Measurement Feedback Info	A5		Not Present		Rel-5			RBC-335
– Choice Mode	A5		FDD					RBC-336
– Downlink 64QAM configured	A5		Not Present		Rel-7			RBC-337
Downlink information common for all radio links	A5, A6		Not Present				RBC-338
Downlink information common for all radio links	A1, A2, A3						RBC-339
– Downlink DPCH info common for all RL							RBC-340
– Timing indicator			Maintain				RBC-341
– CFN-targetSFN frame offset			Not Present				RBC-342
– Downlink DPCH power control information							RBC-343
– DPC mode			0 (single)				RBC-344
– CHOICE mode			FDD				RBC-345
– Power offset PPilot-DPDCH			0				RBC-346
– DL rate matching restriction information			Not Present				RBC-347
– Spreading factor			Reference to clause 6.10 Parameter Set				RBC-348
– Fixed or Flexible Position			Reference to clause 6.10 Parameter Set				RBC-349
– TFCI existence			Reference to clause 6.10 Parameter Set				RBC-350
– CHOICE SF			Reference to clause 6.10 Parameter Set				RBC-351
– DPCH compressed mode info			Not Present				RBC-352
– TX Diversity mode			None				RBC-353
– SSDT information			Not Present		R99 and Rel-4 only		RBC-354
– Default DPCH Offset Value			Not Present				RBC-355
– MAC-hs reset indicator			Not Present		Rel-5		RBC-356
Downlink information common for all radio links	A4						RBC-357
– Downlink DPCH info common for all RL							RBC-358
– Timing indicator			Initialize				RBC-359
– CFN-targetSFN frame offset			Not Present				RBC-360
– Downlink DPCH power control information							RBC-361
– DPC mode			0 (single)				RBC-362
– CHOICE mode			FDD				RBC-363
– Power offset PPilot-DPDCH			0				RBC-364
– DL rate matching restriction information			Not Present				RBC-365
– Spreading factor			Reference to clause 6.10 Parameter Set				RBC-366
– Fixed or Flexible Position			Reference to clause 6.10 Parameter Set				RBC-367
– TFCI existence			Reference to clause 6.10 Parameter Set				RBC-368
– CHOICE SF			Reference to clause 6.10 Parameter Set				RBC-369
– DPCH compressed mode info			Not Present				RBC-370
– TX Diversity mode			None				RBC-371
– SSDT information			Not Present		R99 and Rel-4 only		RBC-372
– Default DPCH Offset Value			Present Arbitrary set to value 0..306688 by step of 512				RBC-373
– MAC-hs reset indicator			Not Present		Rel-5		RBC-374
Downlink information per radio link list	A1, A2, A3						RBC-375
-Downlink information for each radio link							RBC-376
– Choice mode			FDD				RBC-377
– Primary CPICH info							RBC-378
– Primary scrambling code			Ref. to the Default setting in clause 6.1 (FDD)				RBC-379
– PDSCH with SHO DCH info			Not Present		R99 and Rel-4 only		RBC-380
– PDSCH code mapping			Not Present		R99 and Rel-4 only		RBC-381
– Serving HS-DSCH radio link indicator			FALSE		Rel-5		RBC-382
– Serving E-DCH radio link indicator			FALSE		Rel-6		RBC-383
– Downlink DPCH info for each RL							RBC-384
– Primary CPICH usage for channel estimation			Primary CPICH may be used				RBC-385
– DPCH frame offset			Set to value Default DPCH Offset Value (as currently stored in SS) mod 38 400				RBC-386
– Secondary CPICH info			Not Present				RBC-387
– Secondary scrambling code							RBC-388
– channelisation code							RBC-389
– DL channelisation code							RBC-390
– Secondary scrambling code			2				RBC-391
– Spreading factor			Reference to clause 6.10 Parameter Set				RBC-392
– Code number			0				RBC-393
– Scrambling code change			Set to value Default1: No code change (if the UE has a compressed mode pattern sequence configured in variable TGPS_IDENTITY or included in the message including IE "Downlink DPCH info for each RL", which is using compressed mode method "SF/2") Set to value Default2: OMIT (otherwise)				RBC-394
– TPC combination index			0				RBC-395
– SSDT Cell Identity			Not Present		R99 and Rel-4 only		RBC-396
– Closed loop timing adjustment mode			Not Present				RBC-397
– E-AGCH Info			Not present		Rel-6		RBC-398
– E-HICH Information			Not present		Rel-6		RBC-399
– E-RGCH Information			Not present		Rel-6		RBC-400
– SCCPCH information for FACH			Not Present		R99 and Rel-4 only		RBC-401
Downlink information per radio link list	A4						RBC-402
-Downlink information for each radio link							RBC-403
– Choice mode			FDD				RBC-404
– Primary CPICH info							RBC-405
– Primary scrambling code			Ref. to the Default setting in clause 6.1 (FDD)				RBC-406
– PDSCH with SHO DCH info			Not Present		R99 and Rel-4 only		RBC-407
– PDSCH code mapping			Not Present		R99 and Rel-4 only		RBC-408
– Serving HS-DSCH radio link indicator			FALSE		Rel-5		RBC-409
– Serving E-DCH radio link indicator			FALSE		Rel-6		RBC-410
– Downlink DPCH info for each RL							RBC-411
– Primary CPICH usage for channel estimation			Primary CPICH may be used				RBC-412
– DPCH frame offset			Set to value : Default DPCH Offset Value mod 38 400				RBC-413
– Secondary CPICH info			Not Present				RBC-414
– Secondary scrambling code							RBC-415
– channelisation code							RBC-416
– DL channelisation code							RBC-417
– Secondary scrambling code			2				RBC-418
– Spreading factor			Reference to clause 6.10 Parameter Set				RBC-419
– Code number			0				RBC-420
– Scrambling code change			Set to value Default1: No code change (if the UE has a compressed mode pattern sequence configured in variable TGPS_IDENTITY or included in the message including IE "Downlink DPCH info for each RL", which is using compressed mode method "SF/2") Set to value Default2: OMIT (otherwise)				RBC-421
– TPC combination index			0				RBC-422
– SSDT Cell Identity			Not Present		R99 and Rel-4 only		RBC-423
– Closed loop timing adjustment mode			Not Present				RBC-424
– E-AGCH Info			Not present		Rel-6		RBC-425
– E-HICH Information			Not present		Rel-6		RBC-426
– E-RGCH Information			Not present		Rel-6		RBC-427
– SCCPCH information for FACH			Not Present		R99 and Rel-4 only		RBC-428
– Downlink information for each radio link	A5						RBC-429
– Choice mode			FDD				RBC-430
– Primary CPICH info							RBC-431
– Primary scrambling code			Ref. to the Default setting in clause 6.1 (FDD)				RBC-432
– PDSCH with SHO DCH info			Not Present		R99 and Rel-4 only		RBC-433
– PDSCH code mapping			Not Present		R99 and Rel-4 only		RBC-434
– Serving HS-DSCH radio link indicator			FALSE		Rel-5		RBC-435
– Serving E-DCH radio link indicator			FALSE		Rel-6		RBC-436
– Downlink DPCH info for each RL			Not present				RBC-437
– E-AGCH Info			Not present		Rel-6		RBC-438
– E-HICH Information			Not present		Rel-6		RBC-439
– E-RGCH Information			Not present		Rel-6		RBC-440
– SCCPCH Information for FACH			Not Present		R99 and Rel-4 only		RBC-441
– Downlink information for each radio link	A6				R99		RBC-442
– Choice mode			FDD				RBC-443
– Primary CPICH info							RBC-444
– Primary scrambling code			Ref. to the Default setting in clause 6.1 (FDD)				RBC-445
– PDSCH with SHO DCH info			Not Present		R99 and Rel-4 only		RBC-446
– PDSCH code mapping			Not Present		R99 and Rel-4 only		RBC-447
– Serving E-DCH radio link indicator			FALSE		Rel-6		RBC-448
– Downlink DPCH info for each RL			Not present				RBC-449
– E-AGCH Info			Not present		Rel-6		RBC-450
– E-HICH Information			Not present		Rel-6		RBC-451
– E-RGCH Information			Not present		Rel-6		RBC-452
– SCCPCH Information for FACH			Not Present		R99 and Rel-4 only		RBC-453
– Downlink information for each radio link	A6		Not Present		Rel-4 only		RBC-454
Downlink secondary cell info FDD	A5		Not Present		Rel-8			RBC-455
Additional downlink secondary cell info list FDD	A5		Not Present		Rel-10			RBC-456
– Downlink secondary cell info FDD	A5		Not Present		Rel-10			RBC-457
Additional downlink secondary cell info list FDD 2 – Downlink secondary cell info FDD 2		A5 A5		Not Present Not Present		Rel-11 Rel-11			RBC-457a
MBMS PL Service Restriction Information	A1,A2,A3,A4,A5,A6		Not Present		Rel-6		RBC-458

Condition	Explanation
A1	This IE need for "Non speech in CS"
A2	This IE need for "Speech in CS"
A3	This IE need for "Packet to CELL_DCH from CELL_DCH in PS"
A4	This IE need for "Packet to CELL_DCH from CELL_FACH in PS"
A5	This IE need for "Packet to CELL_FACH from CELL_DCH in PS"
A6	This IE need for "Packet to CELL_FACH from CELL_FACH in PS"

Contents of RADIO BEARER RECONFIGURATION FAILURE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if it is set to identical value of the same IE in the downlink RADIO BEARER RECONFIGURATION message.
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Failure cause	Checked to see if it meets test requirement
Radio bearers for which reconfiguration would have succeeded List	Not checked

Contents of RADIO BEARER RECONFIGURATION COMPLETE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if the value is identical to the same IE in the downlink RADIO BEARER RECONFIGURATION COMPLETE message
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Uplink integrity protection activation info	Not checked
CHOICE mode	FDD
Deferred measurement control reading	Not present for Rel-7 or later, otherwise Not checked
COUNT-C activation time	Not checked
Radio bearer uplink ciphering activation time info	Not checked
Uplink counter synchronization info	Not present

Contents of RADIO BEARER RELEASE message: AM or UM

Information Element	Condition	Value/remark	Version	Index
Message Type	A1, A2, A3, A4, A5, A6, A7, A8			RBR-001
Message Type	, A9, A10		Rel-5	RBR-002
RRC transaction identifier		Arbitrarily selects an integer between 0 and 3		RBR-003
Integrity check info				RBR-004
– message authentication code		SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.		RBR-005
– RRC message sequence number		SS provides the value of this IE, from its internal counter.		RBR-006
Integrity protection mode info		Not Present		RBR-007
Ciphering mode info		Not Present		RBR-008
Activation time	A1, A2, A3, A7, A8	(256+CFN-(CFN MOD 8 + 8))MOD 256		RBR-009
Activation time	, A9, A10	(256+CFN-(CFN MOD 8 + 8))MOD 256	Rel-5	RBR-010
Activation time	A4, A5, A6	Not Present		RBR-011
New U-RNTI		Not Present		RBR-012
New C-RNTI	A1,A2,A3,A4	Not Present		RBR-013
New C-RNTI	, A9	Not Present	Rel-5	RBR-014
New C-RNTI	A5, A6, A7, A8	‘1010 1010 1010 1010’		RBR-015
New C-RNTI	, A10	‘1010 1010 1010 1010’	Rel-5	RBR-016
New DSCH-RNTI	A1, A2, A3, A4, A5, A6, A7, A8	Not Present	R99 and Rel-4 only	RBR-017
New H-RNTI	A1, A2, A3, A4, A5, A6, A7, A8	Not Present		RBR-018
New H-RNTI	, A9, A10,	Not Present	Rel-5	RBR-019
New Primary E-RNTI		Not Present	Rel-6	RBR-020
New Secondary E-RNTI		Not Present	Rel-6	RBR-021
RRC State indicator	A1,A2, A3, A4	CELL_DCH		RBR-022
RRC State indicator	, A9	CELL_DCH	Rel-5	RBR-023
RRC State indicator	A5, A6, A7, A8	CELL_FACH		RBR-024
RRC State indicator	, A10	CELL_FACH	Rel-5	RBR-025
UE Mobility State Indicator		Not Present	Rel-7	RBR-026
UTRAN DRX cycle length coefficient	A1,A2,A3,A4,A5,A6, A7, A8	Not Present		RBR-027
UTRAN DRX cycle length coefficient	, A9, A10	Not Present	Rel-5	RBR-028
CN information info		Not Present		RBR-029
Signalling Connection release indication		Not Present		RBR-030
URA identity		Not Present		RBR-031
RNC support for change of UE capability		Not Present	Rel-7	RBR-032
RAB information to reconfigure list		Not Present		RBR-033
RB information to release	A1,A2, A7, A8			RBR-034
– RB identity		10		RBR-035
RB information to release	A2, A8			RBR-036
– RB identity		11		RBR-037
RB information to release	A2, A8			RBR-038
– RB identity		12		RBR-039
RB information to release	A3, A4, A5, A6			RBR-040
– RB identity		20		RBR-041
RB information to release	A9, A10		Rel-5	RBR-042
– RB identity		25		RBR-043
RB information to reconfigure list	A1,A2, A3,A4,A5, A6, A7, A8, A9, A10	Not Present	Rel-6	RBR-044
RB information to be affected	A1,A2, A3,A4,A5, A6, A7, A8	Not Present		RBR-045
RB information to be affected	, A9, A10	Not Present	Rel-5	RBR-046
Downlink counter synchronization info	A1,A2,A3,A4,A5,A6, A7, A8	Not Present		RBR-047
Downlink counter synchronization info	, A9, A10	Not Present	Rel-5	RBR-048
UL Transport channel information for all transport channels	A1, A2, A3, A4, A5, A6, A7, A8	TFCS reconfigured to fit the new transport channel configuration.		RBR-049
UL Transport channel information for all transport channels	, A9, A10		Rel-5	RBR-050
Deleted UL TrCH Information	A1,A2, A3, A4, A5, A6, A7, A8			RBR-051
Deleted UL TrCH Information	, A9, A10		Rel-5	RBR-052
– Uplink transport channel type		DCH		RBR-053
– Transport channel identity		1		RBR-054
Deleted UL TrCH Information	A2, A8			RBR-055
– Uplink transport channel type		DCH		RBR-056
– Transport channel identity		2		RBR-057
Deleted UL TrCH Information	A2, A8			RBR-058
– Uplink transport channel type		DCH		RBR-059
– Transport channel identity		3		RBR-060
Added or Reconfigured UL TrCH information	A5, A6, A7, A8	Not Present		RBR-061
Added or Reconfigured UL TrCH information	, A10	Not Present	Rel-5	RBR-062
Added or Reconfigured UL TrCH information	A1, A2, A3, A4	TrCHs(DCH for DCCH )		RBR-063
Added or Reconfigured UL TrCH information	, A9	TrCHs(DCH for DCCH )	Rel-5	RBR-064
– Uplink transport channel type		DCH		RBR-065
– UL Transport channel identity		5		RBR-066
– TFS				RBR-067
– CHOICE Transport channel type		Dedicated transport channels		RBR-068
– Dynamic Transport format information				RBR-069
– RLC Size		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RBR-070
– Number of TBs and TTI List		(This IE is repeated for TFI number.)		RBR-071
– Transmission Time Interval		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RBR-072
– Number of Transport blocks		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RBR-073
– CHOICE Logical channel list		All		RBR-074
– Semi-static Transport Format information				RBR-075
– Transmission time interval		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RBR-076
– Type of channel coding		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RBR-077
– Coding Rate		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RBR-078
– Rate matching attribute		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RBR-079
– CRC size		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RBR-080
DL Transport channel information for all transport channels	A1, A2, A3, A4, A5, A6, A7, A8	TFCS reconfigured to fit the new transport channel configuration.		RBR-081
DL Transport channel information for all transport channels	, A9, A10		Rel-5	RBR-082
Deleted DL TrCH Information	A1, A2, A3, A4, A5, A6, A7, A8			RBR-083
Deleted DL TrCH Information	, A9		Rel-5	RBR-084
– Downlink transport channel type		DCH		RBR-085
– Transport channel identity		6		RBR-086
Deleted DL TrCH Information	A2, A8			RBR-087
– Downlink transport channel type		DCH		RBR-088
– Transport channel identity		7		RBR-089
Deleted DL TrCH Information	A2, A8			RBR-090
– Downlink transport channel type		DCH		RBR-091
– Transport channel identity		8		RBR-092
Deleted DL TrCH Information	A9, A10		Rel-5	RBR-093
– Downlink transport channel type		HS-DSCH		RBR-094
– DL HS-DSCH MAC-d flow identity		0		RBR-095
Added or Reconfigured DL TrCH information	A5, A6, A7, A8	Not Present		RBR-096
Added or Reconfigured DL TrCH information	, A10	Not Present	Rel-5	RBR-097
Added or Reconfigured DL TrCH information	A1, A2, A3, A4	1 TrCHs(DCH for DCCH)		RBR-098
Added or Reconfigured DL TrCH information	, A9	1 TrCHs(DCH for DCCH)	Rel-5	RBR-099
– Downlink transport channel type		DCH		RBR-100
– DL Transport channel identity		10		RBR-101
– CHOICE DL parameters		Same as UL		RBR-102
– Uplink transport channel type		DCH		RBR-103
– UL TrCH identity		5		RBR-104
– DCH quality target				RBR-105
– BLER Quality value		Not Present		RBR-106
Frequency info	A1,A2,A3,A4,A5, A7, A8			RBR-107
Frequency info	, A9, A10		Rel-5	RBR-108
– UARFCN uplink (Nu)		Not present Absence of this IE is equivalent to applying the default duplex distance defined for the operating frequency according to 3GPP TS 25.101 [11]		RBR-109
– UARFCN downlink (Nd)		Reference to clause 5.1 Test frequencies		RBR-110
DTX-DRX timing information		Not Present	Rel-7	RBR-111
DTX-DRX Information		Not Present	Rel-7	RBR-112
HS-SCCH less Information		Not Present	Rel-7	RBR-113
MIMO parameters		Not Present	Rel-7	RBR-114
Maximum allowed UL TX power		33dBm		RBR-115
Frequency info	A6	Not Present		RBR-116
CHOICE channel requirement	A5, A6, A7, A8	Not Present		RBR-117
CHOICE channel requirement	, A10	Not Present	Rel-5	RBR-118
CHOICE channel requirement	A1, A2, A3, A4	Uplink DPCH info		RBR-119
CHOICE channel requirement	, A9	Uplink DPCH info	Rel-5	RBR-120
– Uplink DPCH power control info				RBR-121
– DPCCH power offset		-40 (-80dB)		RBR-122
– PC Preamble		1 frame		RBR-123
– SRB delay		7 frames		RBR-124
– Power Control Algorithm		Algorithm1		RBR-125
– ACK		Not Present	Rel-5	RBR-126
– NACK		Not Present	Rel-5	RBR-127
– Ack-Nack repetition factor		Not Present	Rel-5	RBR-128
– TPC step size		0 (1dB)		RBR-129
– Scrambling code type		Long		RBR-130
– Scrambling code number		0 (0 to 16777215)		RBR-131
– Number of DPDCH		Not Present(1)		RBR-132
– spreading factor		Reference to clause 6.10 Parameter Set		RBR-133
– TFCI existence		Reference to clause 6.10 Parameter Set		RBR-134
– Number of FBI bit		Reference to clause 6.10 Parameter Set		RBR-135
– Number of TPC bits		Not Present	Rel-7	RBR-136
– Puncturing Limit		Reference to clause 6.10 Parameter Set		RBR-137
E-DCH Info		Not Present	Rel-6	RBR-138
CHOICE Mode	A1,A2,A3,A4,A5,A6, A7, A8	FDD		RBR-139
CHOICE Mode	, A9, A10	FDD	Rel-5	RBR-140
– Downlink PDSCH information		Not Present	R99 and Rel-4 only	RBR-141
Downlink HS-PDSCH Information	A1, A2, A3, A4, A5, A6, A7, A8, A9, A10	Not Present	Rel-5	RBR-142
Downlink information common for all radio links	A5, A6, A7, A8	Not Present		RBR-143
Downlink information common for all radio links	, A10	Not Present	Rel-5	RBR-144
Downlink information common for all radio links	A1,A2, A3			RBR-145
Downlink information common for all radio links	, A9		Rel-5	RBR-146
– Downlink DPCH info common for all RL				RBR-147
– Timing indicator		Maintain		RBR-148
– CFN-targetSFN frame offset		Not Present		RBR-149
– Downlink DPCH power control information				RBR-150
– DPC mode		0 (single)		RBR-151
– CHOICE mode		FDD		RBR-152
– Power offset PPilot-DPDCH		0		RBR-153
– DL rate matching restriction information		Not Present		RBR-154
– Spreading factor		Reference to clause 6.10 Parameter Set		RBR-155
– Fixed or Flexible Position		Reference to clause 6.10 Parameter Set		RBR-156
– TFCI existence		Reference to clause 6.10 Parameter Set		RBR-157
– CHOICE SF		Reference to clause 6.10 Parameter Set		RBR-158
– DPCH compressed mode info		Not Present		RBR-159
– TX Diversity mode		None		RBR-160
– SSDT information		Not Present	R99 and Rel-4 only	RBR-161
– Default DPCH Offset Value		Not Present		RBR-162
– MAC-hs reset indicator		Not Present	Rel-5	RBR-163
Downlink information common for all radio links	A4			RBR-164
– Downlink DPCH info common for all RL				RBR-165
– Timing indicator		Initialize		RBR-166
– CFN-targetSFN frame offset		Not Present		RBR-167
– Downlink DPCH power control information				RBR-168
– DPC mode		0 (single)		RBR-169
– CHOICE mode		FDD		RBR-170
– Power offset PPilot-DPDCH		0		RBR-171
– DL rate matching restriction information		Not Present		RBR-172
– Spreading factor		Reference to clause 6.10 Parameter Set		RBR-173
– Fixed or Flexible Position		Reference to clause 6.10 Parameter Set		RBR-174
– TFCI existence		Reference to clause 6.10 Parameter Set		RBR-175
– CHOICE SF		Reference to clause 6.10 Parameter Set		RBR-176
– DPCH compressed mode info		Not Present		RBR-177
– TX Diversity mode		None		RBR-178
– SSDT information		Not Present	R99 and Rel-4 only	RBR-179
– Default DPCH Offset Value		Arbitrary set to value 0..306688 by step of 512		RBR-180
– MAC-hs reset indicator		Not Present	Rel-5	RBR-181
Downlink information for each radio link list	A1,A2,A3			RBR-182
Downlink information for each radio link list	, A9		Rel-5	RBR-183
-Downlink information for each radio link				RBR-184
– Choice mode		FDD		RBR-185
– Primary CPICH info				RBR-186
– Primary scrambling code		Ref. to the Default setting in clause 6.1 (FDD)		RBR-187
– PDSCH with SHO DCH info		Not Present	R99 and Rel-4 only	RBR-188
– PDSCH code mapping		Not Present	R99 and Rel-4 only	RBR-189
– Serving HS-DSCH radio link indicator		FALSE	Rel-5	RBR-190
– Serving E-DCH radio link indicator		FALSE	Rel-6	RBR-191
– Downlink DPCH info for each RL				RBR-192
– Primary CPICH usage for channel estimation		Primary CPICH may be used		RBR-193
– DPCH frame offset		Set to value Default DPCH Offset Value (as currently stored in SS) mod 38 400		RBR-194
– Secondary CPICH info		Not Present		RBR-195
– Secondary scrambling code				RBR-196
– channelisation code				RBR-197
– DL channelisation code				RBR-198
– Secondary scrambling code		3		RBR-199
– Spreading factor		Reference to clause 6.10 Parameter Set		RBR-200
– Code number		0		RBR-201
– Scrambling code change		Set to value Default1: No code change (if the UE has a compressed mode pattern sequence configured in variable TGPS_IDENTITY or included in the message including IE "Downlink DPCH info for each RL", which is using compressed mode method "SF/2") Set to value Default2: OMIT (otherwise)		RBR-202
– TPC combination index		0		RBR-203
– SSDT Cell Identity		Not Present	R99 and Rel-4 only	RBR-204
– Closed loop timing adjustment mode		Not Present		RBR-205
– E-AGCH Info		Not present	Rel-6	RBR-206
– E-HICH Information		Not present	Rel-6	RBR-207
– E-RGCH Information		Not present	Rel-6	RBR-208
– SCCPCH information for FACH		Not Present	R99 and Rel-4 only	RBR-209
Downlink information for each radio link list	A4			RBR-210
-Downlink information for each radio link				RBR-211
– Choice mode		FDD		RBR-212
– Primary CPICH info				RBR-213
– Primary scrambling code		Ref. to the Default setting in clause 6.1 (FDD)		RBR-214
– PDSCH with SHO DCH info		Not Present	R99 and Rel-4 only	RBR-215
– PDSCH code mapping		Not Present	R99 and Rel-4 only	RBR-216
– Serving HS-DSCH radio link indicator		FALSE	Rel-5	RBR-217
– Serving E-DCH radio link indicator		FALSE	Rel-6	RBR-218
– Downlink DPCH info for each RL				RBR-219
– Primary CPICH usage for channel estimation		Primary CPICH may be used		RBR-220
– DPCH frame offset		Set to value : Default DPCH Offset Value mod 38 400		RBR-221
– Secondary CPICH info		Not Present		RBR-222
– Secondary scrambling code				RBR-223
– channelisation code				RBR-224
– DL channelisation code				RBR-225
– Secondary scrambling code		3		RBR-226
– Spreading factor		Reference to clause 6.10 Parameter Set		RBR-227
– Code number		0		RBR-228
– Scrambling code change		Set to value Default1: No code change (if the UE has a compressed mode pattern sequence configured in variable TGPS_IDENTITY or included in the message including IE "Downlink DPCH info for each RL", which is using compressed mode method "SF/2") Set to value Default2: OMIT (otherwise)		RBR-229
– TPC combination index		0		RBR-230
– SSDT Cell Identity		Not Present	R99 and Rel-4 only	RBR-231
– Closed loop timing adjustment mode		Not Present		RBR-232
– E-AGCH Info		Not present	Rel-6	RBR-233
– E-HICH Information		Not present	Rel-6	RBR-234
– E-RGCH Information		Not present	Rel-6	RBR-235
– SCCPCH information for FACH		Not Present	R99 and Rel-4 only	RBR-236
– Downlink information for each radio link	A5, A7, A8			RBR-237
– Choice mode		FDD		RBR-238
– Primary CPICH info				RBR-239
– Primary scrambling code		Ref. to the Default setting in clause 6.1 (FDD)		RBR-240
– PDSCH with SHO DCH info		Not Present	R99 and Rel-4 only	RBR-241
– PDSCH code mapping		Not Present	R99 and Rel-4 only	RBR-242
– Serving HS-DSCH radio link indicator		FALSE	Rel-5	RBR-243
– Serving E-DCH radio link indicator		FALSE	Rel-6	RBR-244
– Downlink DPCH info for each RL		Not present		RBR-245
– E-AGCH Info		Not present	Rel-6	RBR-246
– E-HICH Information		Not present	Rel-6	RBR-247
– E-RGCH Information		Not present	Rel-6	RBR-248
– SCCPCH information for FACH		Not Present	R99 and Rel-4 only	RBR-249
– Downlink information for each radio link	A6, A10	Not Present		RBR-250
MBMS PL Service Restriction Information	A1,A2, A3,A4,A5, A6, A7, A8, A9, A10	Not Present	Rel-6	RBR-251
MBMS RB list released to change transfer mode		Not Present	Rel-6	RBR-252

Condition	Explanation	Version
A1	This IE need for "Non speech in CS"
A2	This IE need for "Speech in CS"
A3	This IE need for "Packet to CELL_DCH from CELL_DCH in PS"
A4	This IE need for "Packet to CELL_DCH from CELL_FACH in PS"
A5	This IE need for "Packet to CELL_FACH from CELL_DCH in PS"
A6	This IE need for "Packet to CELL_FACH from CELL_FACH in PS"
A7	This IE need for "Non speech to CELL_FACH from CELL_DCH in CS"
A8	This IE need for "Speech to CELL_FACH from CELL_DCH in CS"
A9	This IE is needed for "Packet to CELL_DCH / HS-DSCH using three multiplexing options", or when not stated otherwise, for "Packet to CELL_DCH from CELL_DCH / HS-DSCH in PS"	Rel-5
A10	This IE is needed for "Packet to CELL_DCH / HS-DSCH using one multiplexing option", or when not stated otherwise, for "Packet to CELL_FACH from CELL_DCH / HS-DSCH in PS"	Rel-5

Contents of RADIO BEARER RELEASE COMPLETE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see the value is identical to the same IE in the downlink RADIO BEARER RELEASE message.
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Uplink integrity protection activation info	Not checked.
CHOICE mode	FDD
Deferred measurement control reading	Not present for Rel-7 or later, otherwise Not checked
COUNT-C activation time	Not checked
Radio bearer uplink ciphering activation time info	Not checked
Uplink counter synchronization info	Not present

Contents of RADIO BEARER RELEASE FAILURE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if it is set to identical value of the same IE in the downlink RADIO BEARER RELEASE message.
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Failure cause	Checked to see if it meets test requirement
Radio bearers for which reconfiguration would have succeeded	Not checked

Contents of RRC CONNECTION REQUEST message: TM

Information Element	Condition	Value/remark	Version
Message Type
Predefined configuration status information		To be checked against requirement if specified	Rel-5
Initial UE identity
– CHOICE UE id type
– TMSI and LAI (GSM-MAP)		Set to the UE’s TMSI and LAI.
Establishment cause		To be checked against requirement if specified
Protocol error indicator		FALSE
UE Specific Behaviour Information 1 idle		This IE will not be checked by default behaviour, but in specific test case.
Domain indicator		To be checked against requirement if specified	Rel-6
Call type		To be checked against requirement if specified	Rel-6
UE capability indication		To be checked against requirement if specified	Rel-6
Support for F-DPCH	A1	TRUE	Rel-6
Support for F-DPCH	A2	Not Present	Rel-6
UE Mobility State Indicator		Not Present	Rel-7
Support for Enhanced F-DPCH		To be checked against requirement if specified	Rel-7
HS-PDSCH in CELL_FACH		To be checked against requirement if specified	Rel-7
MAC-ehs support		To be checked against requirement if specified	Rel-7
DPCCH Discontinuous Transmission support		To be checked against requirement if specified	Rel-7
Measured results on RACH		To be checked against requirement if specified	Rel-4
Access stratum release indicator		To be checked against requirement if specified	Rel-4

Condition	Explanation
A1	This IE need to be set to TRUE when F-DPCH is fully supported by the UE.
A2	This IE need to be absent when F-DPCH is not fully supported by the UE.

Contents of RRC CONNECTION REJECT message: UM

Information Element	Value/remark
Message Type
RRC transaction identifier	Arbitrarily selects an integer between 0 and 3
Initial UE identity	Select the same type as in the IE "Initial UE Identity" in RRC CONNECTION REQUEST" message.
Rejection cause	Unspecified
Wait Time	0
Redirection info	Not Present

Contents of RRC CONNECTION RELEASE message: UM

Information Element	Value/remark	Version
Message Type
U-RNTI	This IE is set to the following value when the message is transmitted on the CCCH. When transmitted on DCCH, this is absent.	R99, Rel-4
– SRNC identity	0000 0000 0001B
– S-RNTI	0000 0000 0000 0000 0001B
CHOICE identity type	This IE is set to the following value when the message is transmitted on the CCCH. When transmitted on DCCH, this is absent.	Rel-5
– U-RNTI
– SRNC identity	0000 0000 0001B
– S-RNTI	0000 0000 0000 0000 0001B
– Group identity	[FFS]
– Group release information	[FFS]
RRC transaction identifier	Arbitrarily selects an integer between 0 and 3
Integrity check info	This IE is present when this message is transmitted on downlink DCCH. Else, this IE and the sub-IEs are omitted.
– Message authentication code	SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	SS provides the value of this IE, from its internal counter.
N308	2 (for CELL_DCH state). Not Present (for UE in other connected mode states).
Release cause	Normal event
UE Mobility State Indicator	Not Present	Rel-7
Rplmn information	Not Present

Contents of RRC CONNECTION RELEASE COMPLETE message: AM or UM

Information Element	Semantics description
Message Type
RRC transaction identifier	The value of this IE is checked to see that it matches the value of the same IE transmitted in the downlink RRC CONNECTION RELEASE message.
Integrity check info
– Message authentication code	Checked to see if it’s identical to the value of XMAC-I calculated by the SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	Checked to see if it is present. This number is used by the SS to compute the XMAC-I
Error indication	Not checked

Contents of RRC CONNECTION SETUP message: UM (Transition to CELL_DCH or in CELL_FACH)

Information Element	Condition	Value/remark	Version	Index
Message Type	A1, A2, A3 , A4, A5, A6			RCS-001
Initial UE identity		Select the same identity as in the IE "Initial UE Identity" in received RRC CONNECTION REQUEST" message		RCS-002
RRC transaction identifier		Arbitrarily selects an integer between 0 and 3		RCS-003
Activation time		Not Present(Now)		RCS-004
New U-RNTI				RCS-005
– SRNC identity		0000 0000 0001B		RCS-006
– S-RNTI		0000 0000 0000 0000 0001B		RCS-007
New C-RNTI	A1, A2, A3	Not present		RCS-008
	A4, A6	‘1010 1010 1010 1010’	Rel-7	RCS-009
New H-RNTI	A1	Not present	Rel-6	RCS-010
	A2	‘1010 1010 1010 1010’	Rel-6	RCS-011
	A3, A4		Rel-7	RCS-012
	A5, A6		Rel-8	RCS-013
New Primary E-RNTI	A1	Not present	Rel-6	RCS-014
	A2, A3	‘1010 1010 1010 1010’	Rel-7	RCS-015
	A5, A6	‘1010 1010 1010 1010’	Rel-8	RCS-016
New Secondary E-RNTI		Not present	Rel-6	RCS-017
RRC State Indicator		CELL_DCH		RCS-018
RRC State Indicator	A4, A6	CELL_FACH		RCS-019
UTRAN DRX cycle length coefficient		9		RCS-020
Capability update requirement				RCS-021
– UE radio access FDD capability update requirement		TRUE		RCS-022
– UE radio access TDD capability update requirement		FALSE		RCS-023
– UE radio access 3.84 Mcps TDD capability update requirement		FALSE	Rel-4	RCS-024
– UE radio access 1.28 Mcps TDD capability update requirement		FALSE	Rel-4	RCS-025
– System specific capability update requirement list		GSM		RCS-026
– System specific capability update requirement list	UTRAN to E-UTRA	GSM, EUTRA	Rel-8	NOTE 2
RNC support for change of UE capability		FALSE	Rel-7	RCS-027
CHOICE specification mode		Complete specification	Rel-5	RCS-028
– Complete specification			Rel-5	RCS-029
– Signalling RB information to setup	A1	(UM DCCH for RRC)		RCS-030
– RB identity		Not Present		RCS-031
– CHOICE RLC info type				RCS-032
– RLC info				RCS-033
– CHOICE Uplink RLC mode		UM RLC		RCS-034
– Transmission RLC discard		Not Present		RCS-035
– CHOICE Downlink RLC mode		UM RLC		RCS-036
– DL UM RLC LI size		7 bit	Rel-6	RCS-037
– One sided RLC re-establishment		FALSE	Rel-6	RCS-038
– RB mapping info				RCS-039
– Information for each multiplexing option		2 RBMuxOptions		RCS-040
– RLC logical channel mapping indicator		Not Present		RCS-041
– Number of RLC logical channels		1		RCS-042
– Uplink transport channel type		DCH		RCS-043
– UL Transport channel identity		5		RCS-044
– Logical channel identity		1		RCS-045
– CHOICE RLC size list		Configured		RCS-046
– MAC logical channel priority		1		RCS-047
– Downlink RLC logical channel info				RCS-048
– Number of RLC logical channels		1		RCS-049
– Downlink transport channel type		DCH		RCS-050
– DL DCH Transport channel identity		10		RCS-051
– DL DSCH Transport channel identity		Not Present		RCS-052
– Logical channel identity		1		RCS-053
– RLC logical channel mapping indicator		Not Present		RCS-054
– Number of RLC logical channels		1		RCS-055
– Uplink transport channel type		RACH		RCS-056
– UL Transport channel identity		Not Present		RCS-057
– Logical channel identity		1		RCS-058
– CHOICE RLC size list		Explicit List		RCS-059
– RLC size index		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-060
– MAC logical channel priority		1		RCS-061
– Downlink RLC logical channel info				RCS-062
– Number of RLC logical channels		1		RCS-063
– Downlink transport channel type		FACH		RCS-064
– DL DCH Transport channel identity		Not Present		RCS-065
– DL DSCH Transport channel identity		Not Present		RCS-066
– Logical channel identity		1		RCS-067
– Signalling RB information to setup	A2	(UM DCCH for RRC)	Rel-6	RCS-068
– RB identity		Not Present		RCS-069
– CHOICE RLC info type				RCS-070
– RLC info				RCS-071
– CHOICE Uplink RLC mode		UM RLC		RCS-072
– Transmission RLC discard		Not Present		RCS-073
– CHOICE Downlink RLC mode		UM RLC		RCS-074
– DL UM RLC LI size		7 bit	Rel-6	RCS-075
– One sided RLC re-establishment		FALSE	Rel-6	RCS-076
– RB mapping info				RCS-077
– Information for each multiplexing option		1 RBMuxOption		RCS-078
– RLC logical channel mapping indicator		Not Present		RCS-079
– Number of RLC logical channels		1		RCS-080
– Uplink transport channel type		E-DCH		RCS-081
– Logical channel identity		1		RCS-082
– E-DCH MAC-d flow identity		1		RCS-083
– DDI		1		RCS-084
– RLC PDU size list		1 RLC PDU size		RCS-085
– RLC PDU size		144 bits		RCS-086
– Include in scheduling info		FALSE		RCS-087
– MAC logical channel priority		1		RCS-088
– Downlink RLC logical channel info				RCS-089
– Number of RLC logical channels		1		RCS-090
– Downlink transport channel type		HS-DSCH		RCS-091
– DL DCH Transport channel identity		Not present		RCS-092
– DL DSCH Transport channel identity		Not Present		RCS-093
– DL HS-DSCH MAC-d flow identity		1		RCS-094
– Logical channel identity		1		RCS-095
– Signalling RB information to setup	A3	(UM DCCH for RRC)	Rel-7	RCS-096
– Signalling RB information to setup	A5, A6	(UM DCCH for RRC)	Rel-8	RCS-097
– RB identity		Not present		RCS-098
– CHOICE RLC info type				RCS-099
– RLC info				RCS-100
– CHOICE Uplink RLC mode		UM RLC		RCS-101
– Transmission RLC discard		Not Present		RCS-102
– CHOICE Downlink RLC mode		UM RLC		RCS-103
– DL UM RLC LI size		7 bit		RCS-104
– One sided RLC re-establishment		FALSE		RCS-105
– Alternative E-bit interpretation		TRUE		RCS-106
– Use special value of HE field		Not present		RCS-107
– RB mapping info				RCS-108
– Information for each multiplexing option		1 RBMuxOption		RCS-109
– RLC logical channel mapping indicator		Not Present		RCS-110
– Number of RLC logical channels		1		RCS-111
– Uplink transport channel type		E-DCH		RCS-112
– Logical channel identity		1		RCS-113
– E-DCH MAC-d flow identity		1		RCS-114
– DDI		1		RCS-115
– CHOICE RLC PDU size		Fixed size	Rel-8	RCS-116
– RLC PDU size list		1 RLC PDU size		RCS-117
– RLC PDU size		144 bits		RCS-118
– Include in scheduling info		FALSE		RCS-119
– MAC logical channel priority		1		RCS-120
– Downlink RLC logical channel info				RCS-121
– Number of RLC logical channels		1		RCS-122
– Downlink transport channel type		HS-DSCH		RCS-123
– DL DCH Transport channel identity		Not present		RCS-124
– DL DSCH Transport channel identity		Not Present		RCS-125
– CHOICE DL MAC header type		MAC-ehs		RCS-126
– DL HS-DSCH MAC-ehs Queue Id		1		RCS-127
– Logical channel identity		1		RCS-128
– Signalling RB information to setup	A4	(UM DCCH for RRC)	Rel-7	RCS-129
– RB identity		Not present		RCS-130
– CHOICE RLC info type				RCS-131
– RLC info				RCS-132
– CHOICE Uplink RLC mode		UM RLC		RCS-133
– Transmission RLC discard		Not Present		RCS-134
– CHOICE Downlink RLC mode		UM RLC		RCS-135
– DL UM RLC LI size		7 bit		RCS-136
– One sided RLC re-establishment		FALSE		RCS-137
– Alternative E-bit interpretation		Not Present		RCS-138
– Use special value of HE field		Not Present		RCS-139
– RB mapping info				RCS-140
– Information for each multiplexing option		1 RBMuxOption		RCS-141
– RLC logical channel mapping indicator		Not Present		RCS-142
– Number of RLC logical channels		1		RCS-143
– Uplink transport channel type		RACH		RCS-144
– UL Transport channel identity		Not Present		RCS-145
– Logical channel identity		1		RCS-146
– CHOICE RLC size list		According to clause 6.10.2.4.4.1 (combinations on PRACH)		RCS-147
– MAC logical channel priority		1		RCS-148
– Downlink RLC logical channel info				RCS-149
– Number of RLC logical channels		1		RCS-150
– Downlink transport channel type		HS-DSCH		RCS-151
– DL DCH Transport channel identity		Not present		RCS-152
– DL DSCH Transport channel identity		Not Present		RCS-153
– CHOICE DL MAC header type		MAC-ehs		RCS-154
– DL HS-DSCH MAC-ehs Queue Id		1		RCS-155
– Logical channel identity		1		RCS-156
– Signalling RB information to setup	A1	(AM DCCH for RRC)		RCS-157
– RB identity		Not Present		RCS-158
– CHOICE RLC info type				RCS-159
– RLC info				RCS-160
– CHOICE Uplink RLC mode		AM RLC		RCS-161
– Transmission RLC discard				RCS-162
– SDU discard mode		No discard		RCS-163
– MAX_DAT		15		RCS-164
– Transmission window size		32		RCS-165
– Timer_RST		500		RCS-166
– Max_RST		1		RCS-167
– Polling info				RCS-168
– Timer_poll_prohibit		200		RCS-169
– Timer_poll		200		RCS-170
– Poll_PDU		Not Present		RCS-171
– Poll_SDU		1		RCS-172
– Last transmission PDU poll		TRUE		RCS-173
– Last retransmission PDU poll		TRUE		RCS-174
– Poll_Window		99		RCS-175
– Timer_poll_periodic		Not Present		RCS-176
– CHOICE Downlink RLC mode		AM RLC		RCS-177
– DL RLC PDU size		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)	Rel-6	RCS-178
– In-sequence delivery		TRUE		RCS-179
– Receiving window size		32		RCS-180
– Downlink RLC status info				RCS-181
– Timer_status_prohibit		200		RCS-182
– Timer_EPC		Not Present		RCS-183
– Missing PDU indicator		TRUE		RCS-184
– Timer_STATUS_periodic		Not Present		RCS-185
– RB mapping info				RCS-186
– Information for each multiplexing option		2 RBMuxOptions		RCS-187
– RLC logical channel mapping indicator		Not Present		RCS-188
– Number of RLC logical channels		1		RCS-189
– Uplink transport channel type		DCH		RCS-190
– UL Transport channel identity		5		RCS-191
– Logical channel identity		2		RCS-192
– CHOICE RLC size list		Configured		RCS-193
– MAC logical channel priority		2		RCS-194
– Downlink RLC logical channel info				RCS-195
– Number of RLC logical channels		1		RCS-196
– Downlink transport channel type		DCH		RCS-197
– DL DCH Transport channel identity		10		RCS-198
– DL DSCH Transport channel identity		Not Present		RCS-199
– Logical channel identity		2		RCS-200
– RLC logical channel mapping indicator		Not Present		RCS-201
– Number of RLC logical channels		1		RCS-202
– Uplink transport channel type		RACH		RCS-203
– UL Transport channel identity		Not Present		RCS-204
– Logical channel identity		2		RCS-205
– CHOICE RLC size list		Explicit List		RCS-206
– RLC size index		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-207
– MAC logical channel priority		2		RCS-208
– Downlink RLC logical channel info				RCS-209
– Number of RLC logical channels		1		RCS-210
– Downlink transport channel type		FACH		RCS-211
– DL DCH Transport channel identity		Not Present		RCS-212
– DL DSCH Transport channel identity		Not Present		RCS-213
– Logical channel identity		2		RCS-214
– Signalling RB information to setup	A2	(AM DCCH for RRC)	Rel-6	RCS-215
– RB identity		Not Present		RCS-216
– CHOICE RLC info type				RCS-217
– RLC info				RCS-218
– CHOICE Uplink RLC mode		AM RLC		RCS-219
– Transmission RLC discard				RCS-220
– SDU discard mode		No discard		RCS-221
– MAX_DAT		15		RCS-222
– Transmission window size		32		RCS-223
– Timer_RST		500		RCS-224
– Max_RST		1		RCS-225
– Polling info				RCS-226
– Timer_poll_prohibit		200		RCS-227
– Timer_poll		200		RCS-228
– Poll_PDU		Not Present		RCS-229
– Poll_SDU		1		RCS-230
– Last transmission PDU poll		TRUE		RCS-231
– Last retransmission PDU poll		TRUE		RCS-232
– Poll_Window		99		RCS-233
– Timer_poll_periodic		Not Present		RCS-234
– CHOICE Downlink RLC mode		AM RLC		RCS-235
– In-sequence delivery		TRUE		RCS-236
– Receiving window size		32		RCS-237
– Downlink RLC status info				RCS-238
– Timer_status_prohibit		200		RCS-239
– Timer_EPC		Not Present		RCS-240
– Missing PDU indicator		TRUE		RCS-241
– Timer_STATUS_periodic		Not Present		RCS-242
– RB mapping info				RCS-243
– Information for each multiplexing option		1 RBMuxOption		RCS-244
– RLC logical channel mapping indicator		Not Present		RCS-245
– Number of RLC logical channels		1		RCS-246
– Uplink transport channel type		E-DCH		RCS-247
– Logical channel identity		2		RCS-248
– E-DCH MAC-d flow identity		1		RCS-249
– DDI		2		RCS-250
– RLC PDU size list		1 RLC PDU size		RCS-251
– RLC PDU size		144 bits		RCS-252
– Include in scheduling info		FALSE		RCS-253
– MAC logical channel priority		2		RCS-254
– Downlink RLC logical channel info				RCS-255
– Number of RLC logical channels		1		RCS-256
– Downlink transport channel type		HS-DSCH		RCS-257
– DL DCH Transport channel identity		Not Present		RCS-258
– DL DSCH Transport channel identity		Not Present		RCS-259
– DL HS-DSCH MAC-d flow identity		1		RCS-260
– Logical channel identity		2		RCS-261
– Signalling RB information to setup	A3	(AM DCCH for RRC)	Rel-7	RCS-262
– Signalling RB information to setup	A5, A6	(AM DCCH for RRC)	Rel-8	RCS-263
– RB identity		Not present		RCS-264
– CHOICE RLC info type				RCS-265
– RLC info				RCS-266
– CHOICE Uplink RLC mode		AM RLC		RCS-267
– Transmission RLC discard				RCS-268
– SDU discard mode		No discard		RCS-269
– MAX_DAT		15		RCS-270
– Transmission window size		32		RCS-271
– Timer_RST		500		RCS-272
– Max_RST		1		RCS-273
– Polling info				RCS-274
– Timer_poll_prohibit		200		RCS-275
– Timer_poll		200		RCS-276
– Poll_PDU		Not Present		RCS-277
– Poll_SDU		1		RCS-278
– Last transmission PDU poll		TRUE		RCS-279
– Last retransmission PDU poll		TRUE		RCS-280
– Poll_Window		99		RCS-281
– Timer_poll_periodic		Not Present		RCS-282
– CHOICE Downlink RLC mode		AM RLC		RCS-283
– CHOICE Downlink RLC PDU Size		Reference to clause 6 Parameter Set		RCS-284
– Length indicator size		7		RCS-285
– In-sequence delivery		TRUE		RCS-286
– Receiving window size		32		RCS-287
– Downlink RLC status info				RCS-288
– Timer_status_prohibit		200		RCS-289
– Timer_EPC		Not Present		RCS-290
– Missing PDU indicator		TRUE		RCS-291
– Timer_STATUS_periodic		Not Present		RCS-292
– Alternative E-bit interpretation		Not Present		RCS-293
– Use special value of HE field		TRUE		RCS-294
– RB mapping info				RCS-295
– Information for each multiplexing option		1 RBMuxOption		RCS-296
– RLC logical channel mapping indicator		Not Present		RCS-297
– Number of RLC logical channels		1		RCS-298
– Uplink transport channel type		E-DCH		RCS-299
– Logical channel identity		2		RCS-300
– E-DCH MAC-d flow identity		1		RCS-301
– DDI		2		RCS-302
– CHOICE RLC PDU size		Fixed size	Rel-8	RCS-303
– RLC PDU size list		1 RLC PDU size		RCS-304
– RLC PDU size		144 bits		RCS-305
– Include in scheduling info		FALSE		RCS-306
– MAC logical channel priority		2		RCS-307
– Downlink RLC logical channel info				RCS-308
– Number of RLC logical channels		1		RCS-309
– Downlink transport channel type		HS-DSCH		RCS-310
– DL DCH Transport channel identity		Not Present		RCS-311
– DL DSCH Transport channel identity		Not Present		RCS-312
– CHOICE DL MAC header type		MAC-ehs		RCS-313
– DL HS-DSCH MAC-ehs Queue Id		1		RCS-314
– Logical channel identity		2		RCS-315
– Signalling RB information to setup	A4	(AM DCCH for RRC)	Rel-7	RCS-316
– RB identity		Not present		RCS-317
– CHOICE RLC info type				RCS-318
– RLC info				RCS-319
– CHOICE Uplink RLC mode		AM RLC		RCS-320
– Transmission RLC discard				RCS-321
– SDU discard mode		No discard		RCS-322
– MAX_DAT		15		RCS-323
– Transmission window size		32		RCS-324
– Timer_RST		500		RCS-325
– Max_RST		1		RCS-326
– Polling info				RCS-327
– Timer_poll_prohibit		200		RCS-328
– Timer_poll		200		RCS-329
– Poll_PDU		Not Present		RCS-330
– Poll_SDU		1		RCS-331
– Last transmission PDU poll		TRUE		RCS-332
– Last retransmission PDU poll		TRUE		RCS-333
– Poll_Window		99		RCS-334
– Timer_poll_periodic		Not Present		RCS-335
– CHOICE Downlink RLC mode		AM RLC		RCS-336
– CHOICE Downlink RLC PDU Size		Reference to clause 6 Parameter Set		RCS-337
– Length indicator size		7		RCS-338
– In-sequence delivery		TRUE		RCS-339
– Receiving window size		32		RCS-340
– Downlink RLC status info				RCS-341
– Timer_status_prohibit		200		RCS-342
– Timer_EPC		Not Present		RCS-343
– Missing PDU indicator		TRUE		RCS-344
– Timer_STATUS_periodic		Not Present		RCS-345
– Alternative E-bit interpretation		Not Present		RCS-346
– Use special value of HE field		Not Present		RCS-347
– RB mapping info				RCS-348
– Information for each multiplexing option		1 RBMuxOption		RCS-349
– RLC logical channel mapping indicator		Not Present		RCS-350
– Number of RLC logical channels		1		RCS-351
– Uplink transport channel type		RACH		RCS-352
– UL Transport channel identity		Not Present		RCS-353
– Logical channel identity		2		RCS-354
– CHOICE RLC size list		Explicit List		RCS-355
– RLC size index		According to clause 6.10.2.4.4.1 (combinations on PRACH)		RCS-356
– MAC logical channel priority		2		RCS-357
– Downlink RLC logical channel info				RCS-358
– Downlink transport channel type		HS-DSCH		RCS-359
– DL DCH Transport channel identity		Not Present		RCS-360
– DL DSCH Transport channel identity		Not Present		RCS-361
– CHOICE DL MAC header type		MAC-ehs		RCS-362
– DL HS-DSCH MAC-ehs Queue Id		1		RCS-363
– Logical channel identity		2		RCS-364
– Signalling RB information to setup	A1	(AM DCCH for NAS_DT High priority)		RCS-365
– RB identity		Not Present		RCS-366
– CHOICE RLC info type				RCS-367
– RLC info				RCS-368
– CHOICE Uplink RLC mode		AM RLC		RCS-369
– Transmission RLC discard				RCS-370
– SDU discard mode		No discard		RCS-371
– MAX_DAT		15		RCS-372
– Transmission window size		32		RCS-373
– Timer_RST		500		RCS-374
– Max_RST		1		RCS-375
– Polling info				RCS-376
– Timer_poll_prohibit		200		RCS-377
– Timer_poll		200		RCS-378
– Poll_PDU		Not present		RCS-379
– Poll_SDU		1		RCS-380
– Last transmission PDU poll		TRUE		RCS-381
– Last retransmission PDU poll		TRUE		RCS-382
– Poll_Window		99		RCS-383
– Timer_poll_periodic		Not Present		RCS-384
– CHOICE Downlink RLC mode		AM RLC		RCS-385
– DL RLC PDU size		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)	Rel-6	RCS-386
– In-sequence delivery		TRUE		RCS-387
– Receiving window size		32		RCS-388
– Downlink RLC status info				RCS-389
– Timer_status_prohibit		200		RCS-390
– Timer_EPC		Not present		RCS-391
– Missing PDU indicator		TRUE		RCS-392
– Timer_STATUS_periodic		Not Present		RCS-393
– RB mapping info				RCS-394
– Information for each multiplexing option		2 RBMuxOptions		RCS-395
– RLC logical channel mapping indicator		Not Present		RCS-396
– Number of RLC logical channels		1		RCS-397
– Uplink transport channel type		DCH		RCS-398
– UL Transport channel identity		5		RCS-399
– Logical channel identity		3		RCS-400
– CHOICE RLC size list		Configured		RCS-401
– MAC logical channel priority		3		RCS-402
– Downlink RLC logical channel info				RCS-403
– Number of RLC logical channels		1		RCS-404
– Downlink transport channel type		DCH		RCS-405
– DL DCH Transport channel identity		10		RCS-406
– DL DSCH Transport channel identity		Not Present		RCS-407
– Logical channel identity		3		RCS-408
– RLC logical channel mapping indicator		Not Present		RCS-409
– Number of RLC logical channels		1		RCS-410
– Uplink transport channel type		RACH		RCS-411
– UL Transport channel identity		Not Present		RCS-412
– Logical channel identity		3		RCS-413
– CHOICE RLC size list		Explicit List		RCS-414
– RLC size index		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-415
– MAC logical channel priority		3		RCS-416
– Downlink RLC logical channel info				RCS-417
– Number of RLC logical channels		1		RCS-418
– Downlink transport channel type		FACH		RCS-419
– DL DCH Transport channel identity		Not Present		RCS-420
– DL DSCH Transport channel identity		Not Present		RCS-421
– Logical channel identity		3		RCS-422
– Signalling RB information to setup	A2	(AM DCCH for NAS_DT High priority)	Rel-6	RCS-423
– RB identity		Not Present		RCS-424
– CHOICE RLC info type				RCS-425
– RLC info				RCS-426
– CHOICE Uplink RLC mode		AM RLC		RCS-427
– Transmission RLC discard				RCS-428
– SDU discard mode		No discard		RCS-429
– MAX_DAT		15		RCS-430
– Transmission window size		32		RCS-431
– Timer_RST		500		RCS-432
– Max_RST		1		RCS-433
– Polling info				RCS-434
– Timer_poll_prohibit		200		RCS-435
– Timer_poll		200		RCS-436
– Poll_PDU		Not present		RCS-437
– Poll_SDU		1		RCS-438
– Last transmission PDU poll		TRUE		RCS-439
– Last retransmission PDU poll		TRUE		RCS-440
– Poll_Window		99		RCS-441
– Timer_poll_periodic		Not Present		RCS-442
– CHOICE Downlink RLC mode		AM RLC		RCS-443
– In-sequence delivery		TRUE		RCS-444
– Receiving window size		32		RCS-445
– Downlink RLC status info				RCS-446
– Timer_status_prohibit		200		RCS-447
– Timer_EPC		Not present		RCS-448
– Missing PDU indicator		TRUE		RCS-449
– Timer_STATUS_periodic		Not Present		RCS-450
– RB mapping info				RCS-451
– Information for each multiplexing option		1 RBMuxOption		RCS-452
– RLC logical channel mapping indicator		Not Present		RCS-453
– Number of RLC logical channels		1		RCS-454
– Uplink transport channel type		E-DCH		RCS-455
– Logical channel identity		3		RCS-456
– E-DCH MAC-d flow identity		1		RCS-457
– DDI		3		RCS-458
– RLC PDU size list		1 RLC PDU size		RCS-459
– RLC PDU size		144 bits		RCS-460
– Include in scheduling info		FALSE		RCS-461
– MAC logical channel priority		3		RCS-462
– Downlink RLC logical channel info				RCS-463
– Number of RLC logical channels		1		RCS-464
– Downlink transport channel type		HS-DSCH		RCS-465
– DL DCH Transport channel identity		Not Present		RCS-466
– DL DSCH Transport channel identity		Not Present		RCS-467
– DL HS-DSCH MAC-d flow identity		1		RCS-468
– Logical channel identity		3		RCS-469
– Signalling RB information to setup	A3	(AM DCCH for NAS_DT High priority)	Rel-7	RCS-470
– Signalling RB information to setup	A5, A6	(AM DCCH for NAS_DT High priority)	Rel-8	RCS-471
– RB identity		Not present		RCS-472
– CHOICE RLC info type				RCS-473
– RLC info				RCS-474
– CHOICE Uplink RLC mode		AM RLC		RCS-475
– Transmission RLC discard				RCS-476
– SDU discard mode		No discard		RCS-477
– MAX_DAT		15		RCS-478
– Transmission window size		32		RCS-479
– Timer_RST		500		RCS-480
– Max_RST		1		RCS-481
– Polling info				RCS-482
– Timer_poll_prohibit		200		RCS-483
– Timer_poll		200		RCS-484
– Poll_PDU		Not Present		RCS-485
– Poll_SDU		1		RCS-486
– Last transmission PDU poll		TRUE		RCS-487
– Last retransmission PDU poll		TRUE		RCS-488
– Poll_Window		99		RCS-489
– Timer_poll_periodic		Not Present		RCS-490
– CHOICE Downlink RLC mode		AM RLC		RCS-491
– CHOICE Downlink RLC PDU Size		Reference to clause 6 Parameter Set		RCS-492
– Length indicator size		7		RCS-493
– In-sequence delivery		TRUE		RCS-494
– Receiving window size		32		RCS-495
– Downlink RLC status info				RCS-496
– Timer_status_prohibit		200		RCS-497
– Timer_EPC		Not Present		RCS-498
– Missing PDU indicator		TRUE		RCS-499
– Timer_STATUS_periodic		Not Present		RCS-500
– Alternative E-bit interpretation		Not Present		RCS-501
– Use special value of HE field		TRUE		RCS-502
– RB mapping info				RCS-503
– Information for each multiplexing option		1 RBMuxOption		RCS-504
– RLC logical channel mapping indicator		Not Present		RCS-505
– Number of RLC logical channels		1		RCS-506
– Uplink transport channel type		E-DCH		RCS-507
– Logical channel identity		3		RCS-508
– E-DCH MAC-d flow identity		1		RCS-509
– CHOICE RLC PDU size		Fixed size	Rel-8	RCS-510
– DDI		2		RCS-511
– RLC PDU size list		1 RLC PDU size		RCS-512
– RLC PDU size		144 bits		RCS-513
– Include in scheduling info		FALSE		RCS-514
– MAC logical channel priority		3		RCS-515
– Downlink RLC logical channel info				RCS-516
– Number of RLC logical channels		1		RCS-517
– Downlink transport channel type		HS-DSCH		RCS-518
– DL DCH Transport channel identity		Not Present		RCS-519
– DL DSCH Transport channel identity		Not Present		RCS-520
– CHOICE DL MAC header type		MAC-ehs		RCS-521
– DL HS-DSCH MAC-ehs Queue Id		1		RCS-522
– Logical channel identity		3		RCS-523
– Signalling RB information to setup	A4	(AM DCCH for NAS_DT High priority)	Rel-7	RCS-524
– RB identity		Not present		RCS-525
– CHOICE RLC info type				RCS-526
– RLC info				RCS-527
– CHOICE Uplink RLC mode		AM RLC		RCS-528
– Transmission RLC discard				RCS-529
– SDU discard mode		No discard		RCS-530
– MAX_DAT		15		RCS-531
– Transmission window size		32		RCS-532
– Timer_RST		500		RCS-533
– Max_RST		1		RCS-534
– Polling info				RCS-535
– Timer_poll_prohibit		200		RCS-536
– Timer_poll		200		RCS-537
– Poll_PDU		Not Present		RCS-538
– Poll_SDU		1		RCS-539
– Last transmission PDU poll		TRUE		RCS-540
– Last retransmission PDU poll		TRUE		RCS-541
– Poll_Window		99		RCS-542
– Timer_poll_periodic		Not Present		RCS-543
– CHOICE Downlink RLC mode		AM RLC		RCS-544
– CHOICE Downlink RLC PDU Size		Reference to clause 6 Parameter Set		RCS-545
– Length indicator size		7		RCS-546
– In-sequence delivery		TRUE		RCS-547
– Receiving window size		32		RCS-548
– Downlink RLC status info				RCS-549
– Timer_status_prohibit		200		RCS-550
– Timer_EPC		Not Present		RCS-551
– Missing PDU indicator		TRUE		RCS-552
– Timer_STATUS_periodic		Not Present		RCS-553
– Alternative E-bit interpretation		Not Present		RCS-554
– Use special value of HE field		Not Present		RCS-555
– RB mapping info				RCS-556
– Information for each multiplexing option		1 RBMuxOption		RCS-557
– RLC logical channel mapping indicator		Not Present		RCS-558
– Number of RLC logical channels		1		RCS-559
– Uplink transport channel type		RACH		RCS-560
– UL Transport channel identity		Not Present		RCS-561
– Logical channel identity		3		RCS-562
– CHOICE RLC size list		Explicit List		RCS-563
– RLC size index		According to clause 6.10.2.4.4.1 (combinations on PRACH)		RCS-564
– MAC logical channel priority		3		RCS-565
– Downlink RLC logical channel info				RCS-566
– Number of RLC logical channels		1		RCS-567
– Downlink transport channel type		HS-DSCH		RCS-568
– DL DCH Transport channel identity		Not Present		RCS-569
– DL DSCH Transport channel identity		Not Present		RCS-570
– CHOICE DL MAC header type		MAC-ehs		RCS-571
– DL HS-DSCH MAC-ehs Queue Id		1		RCS-572
– Logical channel identity		3		RCS-573
– Signalling RB information to setup	A1	(AM DCCH for NAS_DT Low priority)		RCS-574
– RB identity		Not Present		RCS-575
– CHOICE RLC info type				RCS-576
– RLC info				RCS-577
– CHOICE Uplink RLC mode		AM RLC		RCS-578
– Transmission RLC discard				RCS-579
– SDU discard mode		No discard		RCS-580
– MAX_DAT		15		RCS-581
– Transmission window size		32		RCS-582
– Timer_RST		500		RCS-583
– Max_RST		1		RCS-584
– Polling info				RCS-585
– Timer_poll_prohibit		200		RCS-586
– Timer_poll		200		RCS-587
– Poll_PDU		Not present		RCS-588
– Poll_SDU		1		RCS-589
– Last transmission PDU poll		TRUE		RCS-590
– Last retransmission PDU poll		TRUE		RCS-591
– Poll_Window		99		RCS-592
– Timer_poll_periodic		Not Present		RCS-593
– CHOICE Downlink RLC mode		AM RLC		RCS-594
– DL RLC PDU size		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)	Rel-6	RCS-595
– In-sequence delivery		TRUE		RCS-596
– Receiving window size		32		RCS-597
– Downlink RLC status info				RCS-598
– Timer_status_prohibit		200		RCS-599
– Timer_EPC		Not Present		RCS-600
– Missing PDU indicator		TRUE		RCS-601
– Timer_STATUS_periodic		Not Present		RCS-602
– RB mapping info				RCS-603
– Information for each multiplexing option		2 RBMuxOptions		RCS-604
– RLC logical channel mapping indicator		Not Present		RCS-605
– Number of RLC logical channels		1		RCS-606
– Uplink transport channel type		DCH		RCS-607
– UL Transport channel identity		5		RCS-608
– Logical channel identity		4		RCS-609
– CHOICE RLC size list		Configured		RCS-610
– MAC logical channel priority		4		RCS-611
– Downlink RLC logical channel info				RCS-612
– Number of RLC logical channels		1		RCS-613
– Downlink transport channel type		DCH		RCS-614
– DL DCH Transport channel identity		10		RCS-615
– DL DSCH Transport channel identity		Not Present		RCS-616
– Logical channel identity		4		RCS-617
– RLC logical channel mapping indicator		Not Present		RCS-618
– Number of RLC logical channels		1		RCS-619
– Uplink transport channel type		RACH		RCS-620
– UL Transport channel identity		Not Present		RCS-621
– Logical channel identity		4		RCS-622
– CHOICE RLC size list		Explicit List		RCS-623
– RLC size index		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-624
– MAC logical channel priority		4		RCS-625
– Downlink RLC logical channel info				RCS-626
– Number of RLC logical channels		1		RCS-627
– Downlink transport channel type		FACH		RCS-628
– DL DCH Transport channel identity		Not Present		RCS-629
– DL DSCH Transport channel identity		Not Present		RCS-630
– Logical channel identity		4		RCS-631
– Signalling RB information to setup	A2	(AM DCCH for NAS_DT Low priority)	Rel-6	RCS-632
– RB identity		Not Present		RCS-633
– CHOICE RLC info type				RCS-634
– RLC info				RCS-635
– CHOICE Uplink RLC mode		AM RLC		RCS-636
– Transmission RLC discard				RCS-637
– SDU discard mode		No discard		RCS-638
– MAX_DAT		15		RCS-639
– Transmission window size		32		RCS-640
– Timer_RST		500		RCS-641
– Max_RST		1		RCS-642
– Polling info				RCS-643
– Timer_poll_prohibit		200		RCS-644
– Timer_poll		200		RCS-645
– Poll_PDU		Not present		RCS-646
– Poll_SDU		1		RCS-647
– Last transmission PDU poll		TRUE		RCS-648
– Last retransmission PDU poll		TRUE		RCS-649
– Poll_Window		99		RCS-650
– Timer_poll_periodic		Not Present		RCS-651
– CHOICE Downlink RLC mode		AM RLC		RCS-652
– In-sequence delivery		TRUE		RCS-653
– Receiving window size		32		RCS-654
– Downlink RLC status info				RCS-655
– Timer_status_prohibit		200		RCS-656
– Timer_EPC		Not Present		RCS-657
– Missing PDU indicator		TRUE		RCS-658
– Timer_STATUS_periodic		Not Present		RCS-659
– RB mapping info				RCS-660
– Information for each multiplexing option		1 RBMuxOption		RCS-661
– RLC logical channel mapping indicator		Not Present		RCS-662
– Number of RLC logical channels		1		RCS-663
– Uplink transport channel type		E-DCH		RCS-664
– Logical channel identity		4		RCS-665
– E-DCH MAC-d flow identity		1		RCS-666
– DDI		4		RCS-667
– RLC PDU size list		1 RLC PDU size		RCS-668
– RLC PDU size		144 bits		RCS-669
– Include in scheduling info		FALSE		RCS-670
– MAC logical channel priority		4		RCS-671
– Downlink RLC logical channel info				RCS-672
– Number of RLC logical channels		1		RCS-673
– Downlink transport channel type		HS-DSCH		RCS-674
– DL DCH Transport channel identity		Not Present		RCS-675
– DL DSCH Transport channel identity		Not Present		RCS-676
– DL HS-DSCH MAC-d flow identity		1		RCS-677
– Logical channel identity		4		RCS-678
– Signalling RB information to setup	A3, A5	(AM DCCH for NAS DT Low priority)	Rel-7	RCS-679
– Signalling RB information to setup	, A6	(AM DCCH for NAS DT Low priority)	Rel-8
– RB identity		Not present		RCS-680
– CHOICE RLC info type				RCS-681
– RLC info				RCS-682
– CHOICE Uplink RLC mode		AM RLC		RCS-683
– Transmission RLC discard				RCS-684
– SDU discard mode		No discard		RCS-685
– MAX_DAT		15		RCS-686
– Transmission window size		32		RCS-687
– Timer_RST		500		RCS-688
– Max_RST		1		RCS-689
– Polling info				RCS-690
– Timer_poll_prohibit		200		RCS-691
– Timer_poll		200		RCS-692
– Poll_PDU		Not Present		RCS-693
– Poll_SDU		1		RCS-694
– Last transmission PDU poll		TRUE		RCS-695
– Last retransmission PDU poll		TRUE		RCS-696
– Poll_Window		99		RCS-697
– Timer_poll_periodic		Not Present		RCS-698
– CHOICE Downlink RLC mode		AM RLC		RCS-699
– CHOICE Downlink RLC PDU Size		Reference to clause 6 Parameter Set		RCS-700
– Length indicator size		7		RCS-701
– In-sequence delivery		TRUE		RCS-702
– Receiving window size		32		RCS-703
– Downlink RLC status info				RCS-704
– Timer_status_prohibit		200		RCS-705
– Timer_EPC		Not Present		RCS-706
– Missing PDU indicator		TRUE		RCS-707
– Timer_STATUS_periodic		Not Present		RCS-708
– Alternative E-bit interpretation		Not Present		RCS-709
– Use special value of HE field		TRUE		RCS-710
– RB mapping info				RCS-711
– Information for each multiplexing option		1 RBMuxOption		RCS-712
– RLC logical channel mapping indicator		Not Present		RCS-713
– Number of RLC logical channels		1		RCS-714
– Uplink transport channel type		E-DCH		RCS-715
– Logical channel identity		4		RCS-716
– E-DCH MAC-d flow identity		1		RCS-717
– CHOICE RLC PDU size		Fixed size	Rel-8	RCS-718
– DDI		2		RCS-719
– RLC PDU size list		1 RLC PDU size		RCS-720
– RLC PDU size		144 bits		RCS-721
– Include in scheduling info		FALSE		RCS-722
– MAC logical channel priority		4		RCS-723
– Downlink RLC logical channel info				RCS-724
– Number of RLC logical channels		1		RCS-725
– Downlink transport channel type		HS-DSCH		RCS-726
– DL DCH Transport channel identity		Not Present		RCS-727
– DL DSCH Transport channel identity		Not Present		RCS-728
– CHOICE DL MAC header type		MAC-ehs		RCS-729
– DL HS-DSCH MAC-ehs Queue Id		1		RCS-730
– Logical channel identity		4		RCS-731
– Signalling RB information to setup	A4	(AM DCCH for NAS DT Low priority)	Rel-7	RCS-732
– RB identity		Not present		RCS-733
– CHOICE RLC info type				RCS-734
– RLC info				RCS-735
– CHOICE Uplink RLC mode		AM RLC		RCS-736
– Transmission RLC discard				RCS-737
– SDU discard mode		No discard		RCS-738
– MAX_DAT		15		RCS-739
– Transmission window size		32		RCS-740
– Timer_RST		500		RCS-741
– Max_RST		1		RCS-742
– Polling info				RCS-743
– Timer_poll_prohibit		200		RCS-744
– Timer_poll		200		RCS-745
– Poll_PDU		Not Present		RCS-746
– Poll_SDU		1		RCS-747
– Last transmission PDU poll		TRUE		RCS-748
– Last retransmission PDU poll		TRUE		RCS-749
– Poll_Window		99		RCS-750
– Timer_poll_periodic		Not Present		RCS-751
– CHOICE Downlink RLC mode		AM RLC		RCS-752
– CHOICE Downlink RLC PDU Size		Reference to clause 6 Parameter Set		RCS-753
– Length indicator size		7		RCS-754
– In-sequence delivery		TRUE		RCS-755
– Receiving window size		32		RCS-756
– Downlink RLC status info				RCS-757
– Timer_status_prohibit		200		RCS-758
– Timer_EPC		Not Present		RCS-759
– Missing PDU indicator		TRUE		RCS-760
– Timer_STATUS_periodic		Not Present		RCS-761
– Alternative E-bit interpretation		Not Present		RCS-762
– Use special value of HE field		Not Present		RCS-763
– RB mapping info				RCS-764
– Information for each multiplexing option		1 RBMuxOption		RCS-765
– RLC logical channel mapping indicator		Not Present		RCS-766
– Number of RLC logical channels		1		RCS-767
– Uplink transport channel type		RACH		RCS-768
– UL Transport channel identity		Not Present		RCS-769
– Logical channel identity		4		RCS-770
– CHOICE RLC size list		Explicit List		RCS-771
– RLC size index		According to clause 6.10.2.4.4.1 (Combinations on PRACH)		RCS-772
– MAC logical channel priority		4		RCS-773
– Downlink RLC logical channel info				RCS-774
– Number of RLC logical channels		1		RCS-775
– Downlink transport channel type		HS-DSCH		RCS-776
– DL DCH Transport channel identity		Not Present		RCS-777
– DL DSCH Transport channel identity		Not Present		RCS-778
– CHOICE DL MAC header type		MAC-ehs		RCS-779
– DL HS-DSCH MAC-ehs Queue Id		1		RCS-780
– Logical channel identity		4		RCS-781
UL Transport channel information for all transport channels	A1			RCS-782
– PRACH TFCS		Not Present		RCS-783
– CHOICE Mode		FDD		RCS-784
– TFC subset		Nor Present		RCS-785
– UL DCH TFCS				RCS-786
– CHOICE TFCI signalling		Normal		RCS-787
– TFCI Field 1 information				RCS-788
– CHOICE TFCS representation		Complete		RCS-789
– TFCS complete reconfigure				RCS-790
– CHOICE CTFC Size		2bit CTFC		RCS-791
– CTFC information		This IE is repeated for TFC numbers according to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-792
– CTFC		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-793
– Power offset information				RCS-794
– CHOICE Gain Factors		Computed Gain Factors (The last TFC is set to Signalled Gain Factors)		RCS-795
– Gain factor ßc		11 (below 64 kbps) 9 (higher than 64 kbps) (Not Present if the above is set to Computed Gain Factors)		RCS-796
– Gain factor ßd		15 (Not Present if the above is set to Computed Gain Factors)		RCS-797
– Reference TFC ID		0		RCS-798
– CHOICE mode		FDD		RCS-799
– Power offset Pp-m		Not Present		RCS-800
UL Transport channel information for all transport channels	A2	Not Present	Rel-6	RCS-801
UL Transport channel information for all transport channels	A3, A4	Not Present	Rel-7	RCS-802
	A5, A6		Rel-8	RCS-803
Added or Reconfigured UL TrCH information	A1			RCS-804
– Uplink transport channel type		DCH		RCS-805
– UL Transport channel identity		5		RCS-806
– TFS				RCS-807
– CHOICE Transport channel type		Dedicated transport channels		RCS-808
– Dynamic Transport format information				RCS-809
– RLC size		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-810
– Number of TBs and TTI lists		(This IE is repeated for TFI number)		RCS-811
– Transmission Time Interval		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-812
– Number of Transport blocks		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-813
– CHOICE Logical channel list		All		RCS-814
– Semi-static Transport Format information				RCS-815
– Transmission time interval		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-816
– Type of channel coding		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-817
– Coding Rate		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-818
– Rate matching attribute		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-819
– CRC size		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-820
Added or Reconfigured UL TrCH information	A2	1 E-DCH added with one DCCH MAC-d flow	Rel-6	RCS-821
	A3		Rel-7	RCS-822
– Uplink transport channel type		E-DCH		RCS-823
– CHOICE UL parameters		E-DCH		RCS-824
– E-DCH Transmission Time Interval		set to 2ms if supported by the UE E-DCH category, or 10ms if the UE E-DCH category does not support 2ms TTI		RCS-825
– HARQ info for E-DCH				RCS-826
– HARQ RV Configuration		rvtable		RCS-827
– Added or reconfigured E-DCH MAC-d flow		(for DCCH)		RCS-828
– E-DCH MAC-d flow identity		1		RCS-829
– E-DCH MAC-d flow power offset		0		RCS-830
– E-DCH MAC-d flow maximum number of retransmissions		7		RCS-831
– E-DCH MAC-d flow multiplexing list		Not Present		RCS-832
– CHOICE transmission grant type		Non-scheduled grant info		RCS-833
– Max MAC-e PDU contents size		162 bits		RCS-834
– 2 ms non-scheduled transmission grant HARQ process allocation		Not Present		RCS-835
Added or Reconfigured UL TrCH information	A4	Not Present	Rel-7	RCS-836
Added or Reconfigured UL TrCH information	A5, A6	1 E-DCH added with one DCCH MAC-d flow	Rel-8	RCS-837
– Uplink transport channel type		E-DCH		RCS-838
– CHOICE UL parameters		E-DCH		RCS-839
– UL MAC header type		MAC-i/is		RCS-840
– E-DCH Transmission Time Interval		set to 2ms if supported by the UE E-DCH category, or 10ms if the UE E-DCH category does not support 2ms TTI		RCS-841
– HARQ info for E-DCH				RCS-842
– HARQ RV Configuration		rvtable		RCS-843
– Added or reconfigured E-DCH MAC-d flow		(for DCCH)		RCS-844
– E-DCH MAC-d flow identity		1		RCS-845
– E-DCH MAC-d flow power offset		0		RCS-846
– E-DCH MAC-d flow maximum number of retransmissions		7		RCS-847
– E-DCH MAC-d flow multiplexing list		Not Present		RCS-848
– CHOICE transmission grant type		Non-scheduled grant info		RCS-849
– Max MAC-e PDU contents size		168 bits		RCS-850
– 2 ms non-scheduled transmission grant HARQ process allocation		Not Present		RCS-851
DL Transport channel information common for all transport channel	A1			RCS-852
– SCCPCH TFCS		Not Present		RCS-853
– CHOICE mode		FDD		RCS-854
– CHOICE DL parameters		Same as UL		RCS-855
DL Transport channel information common for all transport channel	A2	Not Present	Rel-6	RCS-856
DL Transport channel information common for all transport channel	A3, A4	Not Present	Rel-7	RCS-857
	A5, A6		Rel-8	RCS-858
Added or Reconfigured DL TrCH information	A1			RCS-859
– Downlink transport channel type		DCH		RCS-860
– DL Transport channel identity		10		RCS-861
– CHOICE DL parameters		Same as UL		RCS-862
– Uplink transport channel type		DCH		RCS-863
– UL TrCH Identity		5		RCS-864
– DCH quality target				RCS-865
– BLER Quality value		-20 (-2.0)		RCS-866
Added or Reconfigured DL TrCH information	A2	1 TrCH (HS-DSCH for DCCH)	Rel-6	RCS-867
– Downlink transport channel type		HS-DSCH		RCS-868
– DL Transport channel identity		Not Present		RCS-869
– CHOICE DL parameters		HS-DSCH		RCS-870
– HARQ Info				RCS-871
– Number of Processes		Reference to clause 6.10.2.4.5 Parameter Set		RCS-872
– CHOICE Memory Partitioning		Implicit		RCS-873
– Added or reconfigured MAC-d flow				RCS-874
– MAC-hs queue to add or reconfigure list		(one queue)		RCS-875
– MAC-hs queue Id		1 (for DCCH)		RCS-876
– MAC-d Flow Identity		1		RCS-877
– T1		50		RCS-878
– MAC-hs window size		16		RCS-879
– MAC-d PDU size Info				RCS-880
– MAC-d PDU size		148		RCS-881
– MAC-d PDU size index		0		RCS-882
– MAC-hs queue to delete list		Not present		RCS-883
– DCH quality target		Not present		RCS-884
Added or Reconfigured DL TrCH information	A3	1 TrCH (HS-DSCH for DCCH)	Rel-7	RCS-885
Added or Reconfigured DL TrCH information	A5 A4 A6	1 TrCH (HS-DSCH for DCCH)	Rel-8 Rel-7 Rel-8	RCS-886
– Downlink transport channel type		HS-DSCH		RCS-887
– DL Transport channel identity		Not Present		RCS-888
– CHOICE DL parameters		HS-DSCH		RCS-889
– HARQ Info				RCS-890
– Number of Processes		Reference to clause 6.10.2.4.5 Parameter Set		RCS-891
– CHOICE Memory Partitioning		Implicit		RCS-892
– CHOICE DL MAC header type		MAC-ehs		RCS-893
– Added or reconfigured MAC-ehs reordering queue				RCS-894
– MAC-ehs queue to add or reconfigure list		(1 queue)		RCS-895
– MAC-ehs queue Id		1		RCS-896
– T1		50		RCS-897
– MAC-ehs window size		16		RCS-898
– MAC-ehs queue to delete list		Not present		RCS-899
– DCH quality target		Not present		RCS-900
Frequency info		Not Present		RCS-901
DTX-DRX timing information		Not present	Rel-7	RCS-902
DTX-DRX Information		Not present	Rel-7	RCS-903
HS-SCCH less Information		Not present	Rel-7	RCS-904
Maximum allowed UL TX power		Not Present		RCS-905
Uplink DPCH info	A1			RCS-907
– Uplink DPCH power control info				RCS-908
– DPCCH power offset		-40 (-80dB)		RCS-909
– PC Preamble		1 frame		RCS-910
– SRB delay		7 frames		RCS-911
– Power Control Algorithm		Algorithm1		RCS-912
– TPC step size		0 (1dB)		RCS-913
– Scrambling code type		Long		RCS-914
– Scrambling code number		0 (0 to 16777215)		RCS-915
– Number of DPDCH		Not Present(1)		RCS-916
– Spreading factor		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-917
– TFCI existence		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-918
– Number of FBI bit		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-919
– Puncturing Limit		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-920
– Number of TPC bits		Not present	Rel-7	RCS-921
Uplink DPCH info	A2		Rel-6	RCS-922
	A3		Rel-7	RCS-923
	A5		Rel-8	RCS-924
– Uplink DPCH power control info				RCS-925
– DPCCH power offset		-40 (-80dB)		RCS-926
– PC Preamble		1 frame		RCS-927
– SRB delay		7 frames		RCS-928
– Power Control Algorithm		Algorithm1		RCS-929
– TPC step size		0 (1dB)		RCS-930
– ACK		3		RCS-931
– NACK		3		RCS-932
– Ack-Nack repetition factor		1		RCS-933
– HARQ_preamble_mode		0		RCS-934
– Scrambling code type		Long		RCS-935
– Scrambling code number		0 (0 to 16777215)		RCS-936
– Number of DPDCH		0		RCS-937
– spreading factor		Not Present		RCS-938
– TFCI existence		FALSE		RCS-939
– Number of FBI bit		Not Present		RCS-940
– Puncturing Limit		Not Present		RCS-941
Uplink DPCH info	A4	Not Present	Rel-7	RCS-942
Uplink DPCH info	A6	Not Present	Rel-8
E-DCH Info	A1	Not Present	Rel-6	RCS-943
E-DCH info	A2		Rel-6	RCS-944
	A3		Rel-7	RCS-945
	A5		Rel-8	RCS-946
– MAC-es/e reset indicator		TRUE		RCS-947
– E-DPCCH info				RCS-948
– E-DPCCH/DPCCH power offset		0		RCS-949
– Happy bit delay condition		100 ms		RCS-950
– E-TFC Boost Info		Not present	Rel-7	RCS-951
– E-DPDCH power interpolation		Not present	Rel-7	RCS-952
– E-DPDCH info				RCS-953
– E-TFCI table index		0		RCS-954
– E-DCH minimum set E-TFCI		9		RCS-955
– Reference E-TFCIs		2 E-TFCIs		RCS-956
– Reference E-TFCI		11		RCS-957
– Reference E-TFCI PO		4		RCS-958
– Reference E-TFCI		83		RCS-959
– Reference E-TFCI PO		16		RCS-960
– Maximum channelisation codes		2sf4		RCS-961
– PLnon-max		0.84		RCS-962
– Scheduling Information Configuration				RCS-963
– Periodicity for Scheduling Info – no grant		Not present		RCS-964
– Periodicity for Scheduling Info – grant		Not present		RCS-965
– Power Offset for Scheduling Info		0		RCS-966
– 3-Index-Step Threshold		Not present		RCS-967
– 2-Index-Step Threshold		Not present		RCS-968
– Scheduled Transmission configuration				RCS-969
– 2ms scheduled transmission grant HARQ process allocation		Not present		RCS-970
– Serving Grant		Not present		RCS-971
– UL 16QAM settings		Not present	Rel-7	RCS-972
E-DCH info	A4	Not Present	Rel-7	RCS-973
E-DCH info	A6	Not Present	Rel-8
Downlink HS-PDSCH Information	A1	Not Present	Rel-6	RCS-974
Downlink HS-PDSCH Information	A2		Rel-6	RCS-975
Downlink HS-PDSCH Information	A5, A6		Rel-8	RCS-976
	A3		Rel-7	RCS-977
– HS-SCCH Info				RCS-978
– CHOICE mode		FDD		RCS-979
– DL Scrambling Code		Not present		RCS-980
– HS-SCCH Channelisation Code Information				RCS-981
– HS-SCCH Channelisation Code		7		RCS-982
– Measurement Feedback Info				RCS-983
– CHOICE mode		FDD		RCS-984
– POhsdsch		6 dB		RCS-985
– CQI Feedback cycle, k		4 ms		RCS-986
– CQI repetition factor		1		RCS-987
– CQI		5 (corresponds to 0dB in relative power offset)		RCS-988
– CHOICE mode		FDD (no data)		RCS-989
– Downlink 64QAM configured		Not present	Rel-7	RCS-990
– HS-DSCH TB size table		Not present	Rel-7	RCS-991
Downlink HS-PDSCH Information	A4	Not present	Rel-7	RCS-992
Downlink information common for all radio links	A1			RCS-993
– Downlink DPCH info common for all RL				RCS-994
– Timing Indication		Initialize		RCS-995
– CFN-targetSFN frame offset		Not Present		RCS-996
– CHOICE mode		FDD		RCS-997
– Downlink DPCH power control information				RCS-998
– DPC mode		0 (single)		RCS-999
– Power offset P Pilot-DPDCH		0		RCS-1000
– DL rate matching restriction information		Not Present		RCS-1001
– Spreading factor		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-1002
– Fixed or Flexible Position		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-1003
– TFCI existence		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-1004
– CHOICE SF		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-1005
– DPCH compressed mode info		Not Present		RCS-1006
– TX Diversity mode		None		RCS-1007
– SSDT information		Not Present	R99 and Rel-4 only	RCS-1008
– Default DPCH Offset Value		Arbitrary set to value 0..306688 by step of 512		RCS-1009
Downlink information common for all radio links	A2		Rel-6	RCS-1010
	A3		Rel-7	RCS-1011
	A5		Rel-8	RCS-1012
– Downlink F-DPCH info common for all RL				RCS-1013
– Timing Indication		Initialise		RCS-1014
– Downlink F-DPCH power control information				RCS-1015
– DPC mode		0 (single)		RCS-1016
– TPC command error rate target		0.04		RCS-1017
– CHOICE mode		FDD		RCS-1018
– DPCH compressed mode info		Not Present		RCS-1019
– TX Diversity mode		None		RCS-1020
– Default DPCH Offset Value		Arbitrary set to value 0..306688 by step of 512		RCS-1021
– MAC-hs reset indicator		TRUE		RCS-1022
Downlink information common for all radio links	A4	Not Present	Rel-7	RCS-1023
	A6		Rel-8
Downlink information for each radio links list	A1			RCS-1024
– Downlink information for each radio links				RCS-1025
– CHOICE mode		FDD		RCS-1026
– Primary CPICH info				RCS-1027
– Primary scrambling code		Reference to clause 6.1 "Default settings (FDD)"		RCS-1028
– PDSCH with SHO DCH info		Not Present	R99 and Rel-4 only	RCS-1029
– PDSCH code mapping		Not Present	R99 and Rel-4 only	RCS-1030
– Serving HS-DSCH radio link indicator		FALSE	Rel-6	RCS-1031
– Serving E-DCH radio link indicator		FALSE	Rel-6	RCS-1032
– Downlink DPCH info for each RL				RCS-1033
– Primary CPICH usage for channel estimation		Primary CPICH may be used		RCS-1034
– DPCH frame offset		Set to value: Default DPCH Offset Value mod 38 400		RCS-1035
– Secondary CPICH info		Not Present		RCS-1036
– DL channelisation code				RCS-1037
– Secondary scrambling code		1		RCS-1038
– Spreading factor		According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		RCS-1039
– Code number		0		RCS-1040
– Scrambling code change		Not Present		RCS-1041
– TPC combination index		0		RCS-1042
– SSDT Cell Identity		Not Present	R99 and Rel-4 only	RCS-1043
– Closed loop timing adjustment mode		Not Present		RCS-1044
– E-AGCH Info		Not Present	Rel-6	RCS-1045
– E-HICH Information		Not Present	Rel-6	RCS-1046
– E-RGCH Information		Not Present	Rel-6	RCS-1047
– SCCPCH information for FACH		Not Present	R99 and Rel-4 only	RCS-1048
Downlink information for each radio link list	A2		Rel-6	RCS-1049
	A3		Rel-7	RCS-1050
	A5		Rel-8	RCS-1051
– Downlink information for each radio link				RCS-1052
– Choice mode		FDD		RCS-1053
– Primary CPICH info				RCS-1054
– Primary scrambling code		Ref. to the Default setting in clause 6.1 (FDD)		RCS-1055
– Serving HS-DSCH radio link indicator		TRUE		RCS-1056
– Serving E-DCH radio link indicator		TRUE		RCS-1057
– Downlink DPCH info for each RL		Not Present		RCS-1058
– Downlink F-DPCH info for each RL				RCS-1059
– Primary CPICH usage for channel estimation		Primary CPICH may be used		RCS-1060
– F-DPCH frame offset		Set to value Default DPCH Offset Value (as currently stored in SS) mod 38 400		RCS-1061
– F-DPCH slot format		Not Present	Rel-7	RCS-1062
– Secondary CPICH info		Not Present		RCS-1063
– Secondary scrambling code		Not Present		RCS-1064
– Code number		12		RCS-1065
– TPC combination index		0		RCS-1066
– E-AGCH Info				RCS-1067
– E-AGCH Channelisation Code		10		RCS-1068
– CHOICE E-HICH Information				RCS-1069
– E-HICH Information				RCS-1070
– Channelisation code		4		RCS-1071
– Signature sequence		1		RCS-1072
– CHOICE E-RGCH Information				RCS-1073
– E-RGCH Information				RCS-1074
– Signature Sequence		0		RCS-1075
– RG combination index		0		RCS-1076
Downlink information for each radio link list	A4	Not Present	Rel-7	RCS-1077
	A6		Rel-8

Condition	Explanation	Version
A1	This IE is needed for “Stand-alone SRBs mapped on DCH/DCH”
A2	This IE is needed for "Stand-alone SRBs mapped on E-DCH and HS-DSCH "	Rel-6
A3	This IE is needed for "Stand-alone SRBs mapped on E-DCH and HS-DSCH using MAC-ehs”	Rel-7
A4	This IE is needed for "Stand-alone SRBs mapped on RACH and HS-DSCH using MAC-ehs” for HS-DSCH reception in CELL_FACH	Rel-7
A5	This IE is needed for "Stand-alone SRBs mapped on E-DCH using MAC-i/is and HS-DSCH using MAC-ehs”	Rel-8
A6	This IE is needed for SRB mapped onto common E-DCH (MAC-i/is) and HS-DSCH (MAC-ehs) in Enhanced CELL_FACH
UTRAN to E-UTRA	This IE is needed for UTRAN to E-UTRA test cases	Rel-8
NOTE 1: If not specified, then A1 will be the default condition NOTE 2: E-UTRA capability is requested on the first RRC connection setup message during test case execution

Contents of RRC CONNECTION SETUP message: UM (Transition to CELL_FACH)

Information Element	Condition		Value/remark		Version		Index
Message Type							RCSU-001
Initial UE identity			Select the same identity as in the IE "Initial UE Identity" in received RRC CONNECTION REQUEST" message				RCSU-002
RRC transaction identifier			Arbitrarily selects an integer between 0 and 3				RCSU-003
Activation time			Not Present (Now)				RCSU-004
New U-RNTI							RCSU-005
– SRNC identity			0000 0000 0001B				RCSU-006
– S-RNTI			0000 0000 0000 0000 0001B				RCSU-007
New C-RNTI			0000 0000 0000 0001B				RCSU-008
New H-RNTI			Not present		Rel-6		RCSU-009
New Primary E-RNTI		Not present		Rel-6		RCSU-010
New Secondary E-RNTI		Not present		Rel-6		RCSU-011
RRC state indicator			CELL_FACH				RCSU-012
UTRAN DRX cycle length coefficient			9				RCSU-013
Capability update requirement							RCSU-014
– UE radio access FDD capability update requirement			TRUE				RCSU-015
– UE radio access TDD capability update requirement			FALSE				RCSU-016
– UE radio access 3.84 Mcps TDD capability update requirement			FALSE		Rel-4		RCSU-017
– UE radio access 1.28 Mcps TDD capability update requirement			FALSE		Rel-4		RCSU-018
– System specific capability update requirement list			GSM				RCSU-019
– System specific capability update requirement list	UTRAN to E-UTRA		GSM, EUTRA		Rel-8
CHOICE specification mode			Complete specification		Rel-5		RCSU-020
– Complete specification					Rel-5		RCSU-021
– Signalling RB information to setup			(UM DCCH for RRC)				RCSU-022
– RB identity			Not present				RCSU-023
– CHOICE RLC info type			RLC info				RCSU-024
– CHOICE Uplink RLC mode			UM RLC				RCSU-025
– Transmission RLC discard			timerBasedNoExplicit : dt50				RCSU-026
– SDU discard mode			Not present				RCSU-027
– CHOICE Downlink RLC mode			UM RLC				RCSU-028
– DL UM RLC LI size			7 bit		Rel-6		RCSU-029
– One sided RLC re-establishment			FALSE		Rel-6		RCSU-030
– RB mapping info							RCSU-031
– Information for each multiplexing option			2 RBMuxOptions				RCSU-032
– RLC logical channel mapping indicator			Not Present				RCSU-033
– Number of uplink RLC logical channels			1				RCSU-034
– Uplink transport channel type			DCH				RCSU-035
– UL Transport channel identity			5				RCSU-036
– Logical channel identity			1				RCSU-037
– CHOICE RLC size list			Configured				RCSU-038
– MAC logical channel priority			1				RCSU-039
– Downlink RLC logical channel info							RCSU-040
– Number of downlink RLC logical channels			1				RCSU-041
– Downlink transport channel type			DCH				RCSU-042
– DL DCH Transport channel identity			10				RCSU-043
– DL DSCH Transport channel identity			Not Present				RCSU-044
– Logical channel identity			1				RCSU-045
– RLC logical channel mapping indicator			Not Present				RCSU-046
– Number of uplink RLC logical channels			1				RCSU-047
– Uplink transport channel type			RACH				RCSU-048
– UL Transport channel identity			Not Present				RCSU-049
– Logical channel identity			1				RCSU-050
– CHOICE RLC size list			Explicit list				RCSU-051
– RLC size index			According to clause 6.10.2.4.4.1				RCSU-052
– MAC logical channel priority			1				RCSU-053
– Downlink RLC logical channel info							RCSU-054
– Number of downlink RLC logical channels			1				RCSU-055
– Downlink transport channel type			FACH				RCSU-056
– DL DCH Transport channel identity			Not Present				RCSU-057
– DL DSCH Transport channel identity			Not Present				RCSU-058
– Logical channel identity			1				RCSU-059
– Signalling RB information to setup			(AM DCCH for RRC)				RCSU-060
– RB identity			Not Present				RCSU-061
– CHOICE RLC info type			RLC info				RCSU-062
– CHOICE Uplink RLC mode			AM RLC				RCSU-063
– Transmission RLC discard							RCSU-064
– SDU discard mode			No Discard				RCSU-065
– MAX_DAT			15				RCSU-066
– Transmission window size			32				RCSU-067
– Timer_RST			500				RCSU-068
– Max_RST			1				RCSU-069
– Polling info							RCSU-070
– Timer_poll_prohibit			200				RCSU-071
– Timer_poll			200				RCSU-072
– Poll_PDU			Not Present				RCSU-073
– Poll_SDU			1				RCSU-074
– Last transmission PDU poll			TRUE				RCSU-075
– Last retransmission PDU poll			TRUE				RCSU-076
– Poll_Windows			99				RCSU-077
– Timer_poll_periodic			Not Present				RCSU-078
– CHOICE Downlink RLC mode			AM RLC				RCSU-079
– DL RLC PDU size			According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		Rel-6		RCSU-080
– In-sequence delivery			TRUE				RCSU-081
– Receiving window size			32				RCSU-082
– Downlink RLC status info							RCSU-083
– Timer_status_prohibit			200				RCSU-084
– Timer_EPC			Not Present				RCSU-085
– Missing PDU indicator			TRUE				RCSU-086
– Timer_STATUS_periodic			Not Present				RCSU-087
– RB mapping info							RCSU-088
– Information for each multiplexing option			2 RBMuxOptions				RCSU-089
– RLC logical channel mapping indicator			Not Present				RCSU-090
– Number of uplink RLC logical channels			1				RCSU-091
– Uplink transport channel type			DCH				RCSU-092
– UL Transport channel identity			5				RCSU-093
– Logical channel identity			2				RCSU-094
– CHOICE RLC size list			Configured				RCSU-095
– MAC logical channel priority			2				RCSU-096
– Downlink RLC logical channel info							RCSU-097
– Number of downlink RLC logical channels			1				RCSU-098
– Downlink transport channel type			DCH				RCSU-099
– DL DCH Transport channel identity			10				RCSU-100
– DL DSCH Transport channel identity			Not Present				RCSU-101
– Logical channel identity			2				RCSU-102
– RLC logical channel mapping indicator			Not Present				RCSU-103
– Number of uplink RLC logical channels			1				RCSU-104
– Uplink transport channel type			RACH				RCSU-105
– UL Transport channel identity			Not Present				RCSU-106
– Logical channel identity			2				RCSU-107
– CHOICE RLC size list			Explicit list				RCSU-108
– RLC size index			According to clause 6.10.2.4.4.1				RCSU-109
– MAC logical channel priority			2				RCSU-110
– Downlink RLC logical channel info							RCSU-111
– Number of downlink RLC logical channels			1				RCSU-112
– Downlink transport channel type			FACH				RCSU-113
– DL DCH Transport channel identity			Not Present				RCSU-114
– DL DSCH Transport channel identity			Not Present				RCSU-115
– Logical channel identity			2				RCSU-116
Signalling RB information to setup			(AM DCCH for NAS_DT High priority)				RCSU-117
– RB identity			Not present				RCSU-118
– CHOICE RLC info type			RLC info				RCSU-119
– CHOICE Uplink RLC mode			AM RLC				RCSU-120
– Transmission RLC discard							RCSU-121
– SDU discard mode			No Discard				RCSU-122
– MAX_DAT			15				RCSU-123
– Transmission window size			32				RCSU-124
– Timer_RST			500				RCSU-125
– Max_RST			1				RCSU-126
– Polling info							RCSU-127
– Timer_poll_prohibit			200				RCSU-128
– Timer_poll			200				RCSU-129
– Poll_PDU			Not Present				RCSU-130
– Poll_SDU			1				RCSU-131
– Last transmission PDU poll			TRUE				RCSU-132
– Last retransmission PDU poll			TRUE				RCSU-133
– Poll_Windows			99				RCSU-134
– Timer_poll_periodic			Not Present				RCSU-135
– CHOICE Downlink RLC mode			AM RLC				RCSU-136
– DL RLC PDU size			According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		Rel-6		RCSU-137
– In-sequence delivery			TRUE				RCSU-138
– Receiving window size			32				RCSU-139
– Downlink RLC status info							RCSU-140
– Timer_status_prohibit			200				RCSU-141
– Timer_EPC			Not Present				RCSU-142
– Missing PDU indicator			TRUE				RCSU-143
– Timer_STATUS_periodic			Not Present				RCSU-144
– RB mapping info							RCSU-145
– Information for each multiplexing option			2 RBMuxOptions				RCSU-146
– RLC logical channel mapping indicator			Not Present				RCSU-147
– Number of uplink RLC logical channels			1				RCSU-148
– Uplink transport channel type			DCH				RCSU-149
– UL Transport channel identity			5				RCSU-150
– Logical channel identity			3				RCSU-151
– CHOICE RLC size list			Configured				RCSU-152
– MAC logical channel priority			3				RCSU-153
– Downlink RLC logical channel info							RCSU-154
– Number of downlink RLC logical channels			1				RCSU-155
– Downlink transport channel type			DCH				RCSU-156
– DL DCH Transport channel identity			10				RCSU-157
– DL DSCH Transport channel identity			Not Present				RCSU-158
– Logical channel identity			3				RCSU-159
– RLC logical channel mapping indicator			Not Present				RCSU-160
– Number of uplink RLC logical channels			1				RCSU-161
– Uplink transport channel type			RACH				RCSU-162
– UL DCH Transport channel identity			Not Present				RCSU-163
– Logical channel identity			3				RCSU-164
– CHOICE RLC size list			Explicit list				RCSU-165
– RLC size index			According to clause 6.10.2.4.4.1				RCSU-166
– MAC logical channel priority			3				RCSU-167
– Downlink RLC logical channel info							RCSU-168
– Number of downlink RLC logical channels			1				RCSU-169
– Downlink transport channel type			FACH				RCSU-170
– DL DCH Transport channel identity			Not Present				RCSU-171
– DL DSCH Transport channel identity			Not Present				RCSU-172
– Logical channel identity			3				RCSU-173
– Signalling RB information to setup			(AM DCCH for NAS_DT Low priority)				RCSU-174
– RB identity			Not Present				RCSU-175
– CHOICE RLC info type			RLC info				RCSU-176
– CHOICE Uplink RLC mode			AM RLC				RCSU-177
– Transmission RLC discard							RCSU-178
– SDU discard mode			No Discard				RCSU-179
– MAX_DAT			15				RCSU-180
– Transmission window size			32				RCSU-181
– Timer_RST			500				RCSU-182
– Max_RST			1				RCSU-183
– Polling info							RCSU-184
– Timer_poll_prohibit			200				RCSU-185
– Timer_poll			200				RCSU-186
– Poll_PDU			Not Present				RCSU-187
– Poll_SDU			1				RCSU-188
– Last transmission PDU poll			TRUE				RCSU-189
– Last retransmission PDU poll			TRUE				RCSU-190
– Poll_Windows			99				RCSU-191
– Timer_poll_periodic			Not Present				RCSU-192
– CHOICE Downlink RLC mode			AM RLC				RCSU-193
– DL RLC PDU size			According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)		Rel-6		RCSU-194
– In-sequence delivery			TRUE				RCSU-195
– Receiving window size			32				RCSU-196
– Downlink RLC status info							RCSU-197
– Timer_status_prohibit			200				RCSU-198
– Timer_EPC			Not Present				RCSU-199
– Missing PDU indicator			TRUE				RCSU-200
– Timer_STATUS_periodic			Not Present				RCSU-201
– RB mapping info							RCSU-202
– Information for each multiplexing option			2 RBMuxOptions				RCSU-203
– RLC logical channel mapping indicator			Not Present				RCSU-204
– Number of uplink RLC logical channels			1				RCSU-205
– Uplink transport channel type			DCH				RCSU-206
– UL Transport channel identity			5				RCSU-207
– Logical channel identity			4				RCSU-208
– CHOICE RLC size list			Configured				RCSU-209
– MAC logical channel priority			4				RCSU-210
– Downlink RLC logical channel info							RCSU-211
– Number of downlink RLC logical channels			1				RCSU-212
– Downlink transport channel type			DCH				RCSU-213
– DL DCH Transport channel identity			10				RCSU-214
– DL DSCH Transport channel identity			Not Present				RCSU-215
– Logical channel identity			4				RCSU-216
– RLC logical channel mapping indicator			Not Present				RCSU-217
– Number of uplink RLC logical channels			1				RCSU-218
– Uplink transport channel type			RACH				RCSU-219
– UL Transport channel identity			Not Present				RCSU-220
– Logical channel identity			4				RCSU-221
– CHOICE RLC size list			Explicit list				RCSU-222
– RLC size index			According to clause 6.10.2.4.4.1				RCSU-223
– MAC logical channel priority			4				RCSU-224
– Downlink RLC logical channel info							RCSU-225
– Number of downlink RLC logical channels			1				RCSU-226
– Downlink transport channel type			FACH				RCSU-227
– DL DCH Transport channel identity			Not Present				RCSU-228
– DL DSCH Transport channel identity			Not Present				RCSU-229
– Logical channel identity			4				RCSU-230
UL Transport channel information for all transport channels							RCSU-231
– PRACH TFCS			Not Present				RCSU-232
– CHOICE Mode			FDD				RCSU-233
– TFC subset			Not Present				RCSU-234
– UL DCH TFCS							RCSU-235
– CHOICE TFCI signalling			Normal				RCSU-236
– TFCI Field 1 information							RCSU-237
– CHOICE TFCS representation			Complete				RCSU-238
– TFCS complete reconfigure							RCSU-239
– CHOICE CTFC Size			2bit CTFC				RCSU-240
– CTFC information			This IE is repeated for TFC numbers according to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)				RCSU-241
– CTFC			According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer)				RCSU-242
– Power offset information							RCSU-243
– CHOICE Gain Factors			Computed Gain Factors (The last TFC is set to Signalled Gain Factors)				RCSU-244
– Gain factor ßc			11 (below 64 kbps) 9 (equal or higher than 64 kbps) when HSDPA is not configured 9 (equal or higher than 64 kbps and below 384 kbps) when HSDPA is also configured 6 (equal or higher than 384 kbps) when HSDPA is also configured (Not Present if the above is set to Computed Gain Factors)				RCSU-245
– Gain factor ßd			15 (Not Present if the above is set to Computed Gain Factors)				RCSU-246
– Reference TFC ID			0				RCSU-247
– CHOICE mode			FDD				RCSU-248
– Power offset Pp-m			Not Present				RCSU-249
Added or Reconfigured TrCH information list			TS 25.331 specifies that "Although this IE is not required when the IE "RRC state indicator" is set to "CELL_FACH", need is MP to align with ASN.1"				RCSU-250
– Added or Reconfigured UL TrCH information							RCSU-251
– Uplink transport channel type			DCH				RCSU-252
– UL Transport channel identity			5				RCSU-253
– TFS							RCSU-254
– CHOICE Transport channel type			Dedicated transport channels				RCSU-255
– Dynamic Transport format information							RCSU-256
– RLC Size			bitMode sizeType2 {part1 2, part2 OMIT} This results in an RLC size of 144 bits				RCSU-257
– Number of TBs and TTI List			List with two entry				RCSU-258
– Transmission Time Interval			Not Present				RCSU-259
– Number of Transport blocks			0				RCSU-260
– Transmission Time Interval			Not Present				RCSU-261
– Number of Transport blocks			1				RCSU-262
– CHOICE Logical channel List			ALL				RCSU-263
– Semi-static Transport Format information							RCSU-264
– Transmission time interval			40 ms				RCSU-265
– Type of channel coding			Convolutional				RCSU-266
– Coding Rate			1/3				RCSU-267
– Rate matching attribute			-170				RCSU-268
– CRC size			16				RCSU-269
DL Transport channel information common for all transport channel							RCSU-270
– SCCPCH TFCS			Not Present				RCSU-271
– CHOICE mode			FDD				RCSU-272
– CHOICE DL parameters			Same as UL				RCSU-273
Added or Reconfigured TrCH information list			TS 25.331 specifies that "Although this IE is not required when the IE "RRC state indicator" is set to "CELL_FACH", need is MP to align with ASN.1"				RCSU-274
– Added or Reconfigured DL TrCH information							RCSU-275
– Downlink transport channel type			DCH				RCSU-276
– DL Transport channel identity			10				RCSU-277
– CHOICE DL parameters			Same as UL				RCSU-278
– Uplink Transport channel type			DCH				RCSU-279
– UL TrCH identity			5				RCSU-280
– DCH quality target			Not Present				RCSU-281
Frequency info			Not present				RCSU-282
Maximum allowed UL TX power			Not present				RCSU-283
CHOICE channel requirement			Not Present				RCSU-284
E-DCH Info			Not Present		Rel-6		RCSU-285
Downlink HS-PDSCH Information			Not Present		Rel-6		RCSU-286
Downlink information common for all radio links			Not Present				RCSU-287
Downlink information for each radio link list			Not present				RCSU-288

Condition	Explanation	Version
UTRAN to E-UTRA	This IE is needed for UTRAN to E-UTRA test cases	Rel-8

Contents of RRC CONNECTION SETUP COMPLETE message: AM

Information Element	Value/remark	Version
Message Type
RRC transaction identifier	The value of this IE is checked to see that it matches the value of the same IE transmitted in the downlink RRC CONNECTION SETUP message.
START list	This IE is checked to see if it is present.
UE radio access capability	Not checked
– Access stratum release indicator	Not checked
– DL capability with simultaneous HS-DSCH configuration	Not checked	REL-5
– PDCP capability	Not checked
– RLC capability	Not checked
– Transport channel capability	Not checked
– RF capability FDD	Not checked
– RF capability TDD	Not checked	REL-4
– RF capability TDD 1.28 Mcps	Not checked	REL-4
– Physical channel capability	Not checked
– UE multi-mode/multi-RAT capability	Not checked
– Security capability
– Ciphering algorithm capability
>UEA0	TRUE
>UEA1	TRUE
>UEA2	To be checked against PICS	REL-7
– Integrity protection algorithm capability
>UIA1	TRUE
>UIA2	To be checked against PICS	REL-7
– UE positioning capability	Not checked
– Measurement capability	Not checked
– Measurement capability TDD	Not checked	REL-8
– Device type	Not checked	REL-6
– Support for System Information Block type 11bis	Not checked	REL-6
– Support for F-DPCH	To be checked against requirement if specified	REL-6
– MAC-ehs support	To be checked against requirement if specified	REL-7
– UE specific capability Information LCR TDD	Not checked	REL-7
– Support for E-DPCCH Power Boosting	Not checked	REL-7
– Support of common E-DCH	To be checked against requirement if specified	REL-8
– Support of MAC-i/is	To be checked against requirement if specified	REL-8
– Support of SPS operation	Not checked	REL-8
– Support of Control Channel DRX operation	Not checked	REL-8
– Support of CSG	To be checked against requirement if specified	REL-8
– Support for Two DRX schemes in URA_PCH and CELL_PCH	To be checked against requirement if specified	REL-7
– Support for E-DPDCH power interpolation formula	Not checked	REL-7
– Support for absolute priority based cell re-selection in UTRAN	To be checked against requirement if specified	REL-8
– Support of MU-MIMO	Not checked	REL-10
– Radio Access Capability Band Combination List	To be checked against requirement if specified	REL-9
– Support of TX Diversity on DL Control Channels by MIMO Capable UE when MIMO operation is active	To be checked against requirement if specified	REL-7
– Support of enhanced TS0	To be checked against requirement if specified	REL-9
– Support for cell-specific Tx diversity configuration for dual-cell operation	To be checked against requirement if specified	REL-8
– CSG proximity indication capability	To be checked against requirement if specified	REL-9
– Neighbour Cell SI acquisition capability	To be checked against requirement if specified	REL-9
– Extended measurements Support	To be checked against requirement if specified	REL-9
– Support for dual cell with MIMO operation in different bands	To be checked against requirement if specified	REL-10
– UE based network performance measurements parameters	To be checked against requirement if specified	REL-10
– Support of UTRAN ANR	To be checked against requirement if specified	REL-10
UE radio access capability extension	Not checked
UE system specific capability	Not checked
Deferred measurement control reading	Not Present for Rel-7 or later, otherwise Not checked
Logged Meas Available	Not checked	REL-10
ANR Logging Results Available	Not checked	REL-10
Connection Establishment Failure Info Available	Not checked	REL-11

Contents of RRC STATUS message: AM

Information Element	Value/remark
Message Type
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Identification of received message	Not Checked
Protocol error information
– Protocol error cause	Refer to test requirement.

Contents of SECURITY MODE COMMAND message: AM

Information Element	Condition	Value/remark	Version
Message Type	A1, A2
RRC transaction identifier		Arbitrarily selects an integer between 0 and 3
Integrity check info
– Message authentication code		Set to MAC-I value computed by the SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message Sequence Number		Set to an arbitrarily selected integer between 0 and 15
Security capability
– Ciphering algorithm capability
– UEA0		If the UE has indicated support for ciphering algorithm UEA0 in the IE "security capability" in the RRC CONNECTION SETUP COMPLETE message, this IE is set to TRUE.
– UEA1		If the UE has indicated support for ciphering algorithm UEA1 in the IE "security capability" in the RRC CONNECTION SETUP COMPLETE message, this IE is set to TRUE.
– UEA2		If the UE has indicated support for ciphering algorithm UEA2 in the IE "security capability" in the RRC CONNECTION SETUP COMPLETE message, this IE is set to TRUE.	Rel-7
– Spare		Spare 3-15 = FALSE
– Integrity protection algorithm capability		0000000000000010B (UIA1)
– UIA1		TRUE
– UIA2		If the UE has indicated support for integrity algorithm UIA2 in the IE "security capability" in the RRC CONNECTION SETUP COMPLETE message, this IE is set to TRUE.	Rel-7
– Spare		Spare 0 and Spare 3-15 = FALSE
Ciphering mode info		This presence of this IE is dependent on IXIT statements in TS 34.123-2. If ciphering is indicated to be active, this IE present with the values of the sub IEs as stated below. Else, this IE is omitted.
– Ciphering mode command		Start/restart
– Ciphering algorithm		UEA0 or UEA1 or UEA2. The indicated algorithm must be one of the algorithms supported by the UE as indicated in the IE "security capability" in the RRC CONNECTION SETUP COMPLETE message.
– Ciphering activation time for DPCH		Not Present
– Radio bearer downlink ciphering activation time info
– Radio bearer activation time
– RB identity		1
– RLC sequence number		Current RLC SN
– RB identity		2
– RLC sequence number		Current RLC SN+2
– RB identity		3
– RLC sequence number		Current RLC SN
– RB identity		4
– RLC sequence number		Current RLC SN
Integrity protection mode info
– Integrity protection mode command		Start
– Downlink integrity protection activation info		Not Present
– Integrity protection algorithm		UIA1 or UIA2. The indicated algorithm must be one of the algorithms supported by the UE as indicated in the IE "security capability" in the RRC CONNECTION SETUP COMPLETE message
– Integrity protection initialisation number		SS selects an arbitrary 32 bits number for FRESH
CN domain identity		CS or PS
UE system specific security capability	A1	Not Checked
UE system specific security capability	A2
– Inter-RAT UE security capability
– CHOICE system		GSM
– GSM security capability		The indicated algorithms must be the same as the algorithms supported by the UE as indicated in the IE " UE system specific capability " in the RRC CONNECTION SETUP COMPLETE message.

Condition	Explanation
A1	UE not supporting GSM
A2	UE supporting GSM

Contents of SECURITY MODE COMPLETE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	The value of this IE is checked to see that it matches the value of the same IE transmitted in the downlink SECURITY MODE COMMAND message.
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Uplink integrity protection activation info	Not checked.
Radio bearer uplink ciphering activation time info	If ciphering is not activated in SECURITY MODE COMMAND message, this IE must be absent. Else, SS checks this IE for the presence of activation times for all ciphered uplink RLC-UM and RLC-AM RBs.

Contents of SECURITY MODE FAILURE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if the value is the identical to the same IE in the downlink SECURITY MODE COMMAND message.
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Failure cause	Refer to test requirement.

Contents of TRANSPORT CHANNEL RECONFIGURATION message: AM or UM

Information Element	Condition	Value/remark	Version	Index
Message Type	A1, A2, A3, A4, A5, A6			TCR-001
RRC transaction identifier		Arbitrarily selects an integer between 0 and 3		TCR-002
Integrity check info				TCR-003
– message authentication code		SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.		TCR-004
– RRC message sequence number		SS provides the value of this IE, from its internal counter.		TCR-005
Integrity protection mode info		Not Present		TCR-006
Ciphering mode info		Not Present		TCR-007
Activation time	A1, A2, A3	(256+CFN-(CFN MOD 8 + 8))MOD 256		TCR-008
Activation time	A4, A5, A6	Not Present		TCR-009
Delay restriction flag	A1, A2, A3, A4, A5, A6	Not Present	Rel-6	TCR-010
New U-RNTI		Not Present		TCR-011
New C-RNTI	A1, A2, A3, A4	Not Present		TCR-012
New C-RNTI	A5, A6	‘1010 1010 1010 1010’		TCR-013
New DSCH-RNTI	A1, A2, A3, A4, A5, A6	Not Present	R99 and Rel-4 only	TCR-014
New H-RNTI	A1, A2, A3, A4, A5, A6	Not Present	Rel-5	TCR-015
New Primary E-RNTI		Not Present	Rel-6	TCR-016
New Secondary E-RNTI		Not Present	Rel-6	TCR-017
RRC State indicator	A1, A2, A3, A4	CELL_DCH		TCR-018
RRC State indicator	A5, A6	CELL_FACH		TCR-019
UE Mobility State Indicator		Not Present	Rel-7	TCR-020
UTRAN DRX cycle length coefficient	A1, A2, A3, A4,A5,A6	Not Present		TCR-021
CN information info		Not Present		TCR-022
URA identity		Not Present		TCR-023
RNC support for change of UE capability		Not Present	Rel-7	TCR-024
Reconfiguration in response to requested change of UE capability		Not Present	Rel-7	TCR-025
Downlink counter synchronization info		Not Present		TCR-026
UL Transport channel information for all transport channels	A1, A2, A5, A6	Not Present		TCR-027
UL Transport channel information for all transport channels	A3, A4			TCR-028
– PRACH TFCS		Not Present		TCR-029
– CHOICE mode		FDD		TCR-030
– TFC subset		Not Present		TCR-031
– UL DCH TFCS				TCR-032
– CHOICE TFCI signalling		Normal		TCR-033
– TFCI Field 1 information				TCR-034
– CHOICE TFCS representation		Complete reconfiguration		TCR-035
– TFCS complete reconfigure information				TCR-036
– CHOICE CTFC Size		Number of bits used must be enough to cover all combinations of CTFC from clause 6.10.2.4 Parameter Set.		TCR-037
– CTFC information		This IE is repeated for TFC numbers and reference to clause 6.10.2.4 Parameter Set		TCR-038
– CTFC		Reference to clause 6.10.2.4 Parameter Set		TCR-039
– Power offset information				TCR-040
– CHOICE Gain Factors		Computed Gain Factors (The last TFC is set to Signalled Gain Factors)		TCR-041
– Gain factor βc		11 (equal or below 64 kbps) when HSDPA is not configured 9 (equal or higher than 64 kbps and below 384 kbps) when HSDPA is also configured 6 (equal or higher than 384 kbps) when HSDPA is also configured 9 (higher than 64 kbps) (Not Present if the CHOICE Gain Factors is set to ComputedGain Factors)		TCR-042
– Gain factor βd		15 (Not Present if the CHOICE Gain Factors is set to ComputedGain Factors)		TCR-043
– Reference TFC ID		0		TCR-044
– CHOICE mode		FDD		TCR-045
– Power offset P p-m		Not Present		TCR-046
Added or Reconfigured UL TrCH information	A1, A2, A5, A6	Not Present		TCR-047
Added or Reconfigured UL TrCH information	A4	2 TrCHs(DCH for DCCH and DCH for DTCH)		TCR-048
– Uplink transport channel type		DCH		TCR-049
– UL Transport channel identity		5		TCR-050
– TFS				TCR-051
– CHOICE Transport channel type		Dedicated transport channels		TCR-052
– Dynamic Transport format information				TCR-053
– RLC Size		Reference to clause 6.10 Parameter Set		TCR-054
– Number of TBs and TTI List		(This IE is repeated for TFI number.)		TCR-055
– Transmission Time Interval		Not Present		TCR-056
– Number of Transport blocks		Reference to clause 6.10 Parameter Set		TCR-057
– CHOICE Logical channel list		All		TCR-058
– Semi-static Transport Format information				TCR-059
– Transmission time interval		Reference to clause 6.10 Parameter Set		TCR-060
– Type of channel coding		Reference to clause 6.10 Parameter Set		TCR-061
– Coding Rate		Reference to clause 6.10 Parameter Set		TCR-062
– Rate matching attribute		Reference to clause 6.10 Parameter Set		TCR-063
– CRC size		Reference to clause 6.10 Parameter Set		TCR-064
– Uplink transport channel type		DCH		TCR-065
– UL Transport channel identity		1		TCR-066
– TFS				TCR-067
– CHOICE Transport channel type		Dedicated transport channels		TCR-068
– Dynamic Transport format information				TCR-069
– RLC Size		Reference to clause 6.10 Parameter Set		TCR-070
– Number of TBs and TTI List		(This IE is repeated for TFI number.)		TCR-071
– Transmission Time Interval		Not Present		TCR-072
– Number of Transport blocks		Reference to clause 6.10 Parameter Set		TCR-073
– CHOICE Logical channel list		All		TCR-074
– Semi-static Transport Format information				TCR-075
– Transmission time interval		Reference to clause 6.10 Parameter Set		TCR-076
– Type of channel coding		Reference to clause 6.10 Parameter Set		TCR-077
– Coding Rate		Reference to clause 6.10 Parameter Set		TCR-078
– Rate matching attribute		Reference to clause 6.10 Parameter Set		TCR-079
– CRC size		Reference to clause 6.10 Parameter Set		TCR-080
Added or Reconfigured UL TrCH information	A3	(DCH for DTCH)		TCR-081
– Uplink transport channel type		DCH		TCR-082
– UL Transport channel identity		1		TCR-083
– TFS				TCR-084
– CHOICE Transport channel type		Dedicated transport channels		TCR-085
– Dynamic Transport format information				TCR-086
– RLC Size		Reference to clause 6.10 Parameter Set		TCR-087
– Number of TBs and TTI List		(This IE is repeated for TFI number.)		TCR-088
– Transmission Time Interval		Not Present		TCR-089
– Number of Transport blocks		Reference to clause 6.10 Parameter Set		TCR-090
– CHOICE Logical channel list		All		TCR-091
– Semi-static Transport Format information				TCR-092
– Transmission time interval		Reference to clause 6.10 Parameter Set		TCR-093
– Type of channel coding		Reference to clause 6.10 Parameter Set		TCR-094
– Coding Rate		Reference to clause 6.10 Parameter Set		TCR-095
– Rate matching attribute		Reference to clause 6.10 Parameter Set		TCR-096
– CRC size		Reference to clause 6.10 Parameter Set		TCR-097
CHOICE mode	A1,A2,A3,A4,A5,A6	Not Present		TCR-098
DL Transport channel information common for all transport channel	A1, A2, A5,A6	Not Present		TCR-099
DL Transport channel information common for all transport channel	A3,A4			TCR-100
– SCCPCH TFCS		Not Present		TCR-101
– CHOICE mode		FDD		TCR-102
– CHOICE DL parameters		Explicit		TCR-103
– DL DCH TFCS				TCR-104
– CHOICE TFCI Signalling		Normal		TCR-105
– TFCI Field 1 Information				TCR-106
– CHOICE TFCS representation		Complete reconfiguration		TCR-107
– TFCS complete reconfigure				TCR-108
– CHOICE CTFC Size		Number of bits used must be enough to cover all combinations of CTFC from clause 6.10.2.4 Parameter Set.		TCR-109
– CTFC information		This IE is repeated for TFC numbers and reference to clause 6.10.2.4		TCR-110
– CTFC		Reference to clause 6.10.2.4 Parameter Set		TCR-111
– Power offset information		Not Present		TCR-112
Added or Reconfigured DL TrCH information	A1, A2, A5, A6	Not Present		TCR-113
Added or Reconfigured DL TrCH information	A4	2 TrCHs(DCH for DCCH and DCH for DTCH)		TCR-114
– Downlink transport channel type		DCH		TCR-115
– DL Transport channel identity		10		TCR-116
– CHOICE DL parameters		Same as UL		TCR-117
– Uplink transport channel type		DCH		TCR-118
– UL TrCH identity		5		TCR-119
– DCH quality target				TCR-120
– BLER Quality value		Not Present		TCR-121
– Downlink transport channel type		DCH		TCR-122
– DL Transport channel identity		6		TCR-123
– CHOICE DL parameters		Explicit Except for RAB with the symmetric DL and UL rate: Same as UL		TCR-124
– TFS				TCR-125
– CHOICE Transport channel type		Dedicated transport channel		TCR-126
– Dynamic transport format information				TCR-127
– RLC Size		Reference to clause 6.10 Parameter Set		TCR-128
– Number of TBs and TTI List		(This IE is repeated for TFI number.)		TCR-129
– Dynamic transport format information				TCR-130
– Transmission Time Interval		Not Present		TCR-131
– Number of Transport blocks		Reference to clause 6.10 Parameter Set		TCR-132
– Semi-static Transport Format information				TCR-133
– Transmission time interval		Reference to clause 6.10 Parameter Set		TCR-134
– Type of channel coding		Reference to clause 6.10 Parameter Set		TCR-135
– Coding Rate		Reference to clause 6.10 Parameter Set		TCR-136
– Rate matching attribute		Reference to clause 6.10 Parameter Set		TCR-137
– CRC size		Reference to clause 6.10 Parameter Set		TCR-138
– DCH quality target				TCR-139
– BLER Quality value		-20 (-2.0)		TCR-140
Added or Reconfigured DL TrCH information	A3			TCR-141
– Downlink transport channel type		DCH		TCR-142
– DL Transport channel identity		6		TCR-143
– CHOICE DL parameters		Explicit Except for RAB with the symmetric DL and UL rate: Same as UL		TCR-144
– TFS				TCR-145
– CHOICE Transport channel type		Dedicated transport channel		TCR-146
– Dynamic transport format information				TCR-147
– RLC Size		Reference to clause 6.10 Parameter Set		TCR-148
– Number of TBs and TTI List		(This IE is repeated for TFI number.)		TCR-149
– Dynamic transport format information				TCR-150
– Transmission Time Interval		Not Present		TCR-151
– Number of Transport blocks		Reference to clause 6.10 Parameter Set		TCR-152
– Semi-static Transport Format information				TCR-153
– Transmission time interval		Reference to clause 6.10 Parameter Set		TCR-154
– Type of channel coding		Reference to clause 6.10 Parameter Set		TCR-155
– Coding Rate		Reference to clause 6.10 Parameter Set		TCR-156
– Rate matching attribute		Reference to clause 6.10 Parameter Set		TCR-157
– CRC size		Reference to clause 6.10 Parameter Set		TCR-158
– DCH quality target				TCR-159
– BLER Quality value		-20 (-2.0)		TCR-160
Frequency info	A1,A2,A3,A4,A5			TCR-161
– UARFCN uplink (Nu)		Not present Absence of this IE is equivalent to applying the default duplex distance defined for the operating frequency according to 3GPP TS 25.101 [11]		TCR-162
– UARFCN downlink (Nd)		Reference to clause 5.1 Test frequencies		TCR-163
Frequency info	A6	Not Present		TCR-164
DTX-DRX timing information		Not Present	Rel-7	TCR-165
DTX-DRX Information		Not Present	Rel-7	TCR-166
HS-SCCH less Information		Not Present	Rel-7	TCR-167
MIMO parameters		Not Present	Rel-7	TCR-168
Maximum allowed UL TX power	A1, A2, A3, A4, A5, A6	33dBm		TCR-169
CHOICE channel requirement	A5, A6	Not Present		TCR-170
CHOICE channel requirement	A1, A2, A3, A4	Uplink DPCH info		TCR-171
-Uplink DPCH power control info				TCR-172
– DPCCH power offset		-40 (-80dB)		TCR-173
– PC Preamble		1 frame		TCR-174
– SRB delay		7 frames		TCR-175
– Power Control Algorithm		Algorithm1		TCR-176
– TPC step size		0 (1dB)		TCR-177
– ACK		Not Present	Rel-5	TCR-178
– NACK		Not Present	Rel-5	TCR-179
– Ack-Nack repetition factor		Not Present	Rel-5	TCR-180
– Scrambling code type		Long		TCR-181
– Scrambling code number		0 (0 to 16777215)		TCR-182
– Number of DPDCH		Not Present(1)		TCR-183
– spreading factor		Reference to clause 6.10 Parameter Set		TCR-184
– TFCI existence		Reference to clause 6.10 Parameter Set		TCR-185
– Number of FBI bit		Reference to clause 6.10 Parameter Set		TCR-186
– Number of TPC bits		Not Present	Rel-7	TCR-187
– Puncturing Limit		Reference to clause 6.10 Parameter Set		TCR-188
E-DCH Info		Not Present	Rel-6	TCR-189
CHOICE Mode	A1, A2, A3, A4, A5, A6	FDD	R99 and Rel-4 only	TCR-190
– Downlink PDSCH information		Not Present	R99 and Rel-4 only	TCR-191
Downlink HS-PDSCH Information	A1, A2, A3, A4, A5, A6	Not Present	Rel-5	TCR-192
Downlink information common for all radio links	A5, A6	Not Present		TCR-193
Downlink information common for all radio links	A1, A2, A3			TCR-194
– Downlink DPCH info common for all RL				TCR-195
– Timing indicator		Maintain		TCR-196
– CFN-targetSFN frame offset		Not Present		TCR-197
– Downlink DPCH power control information				TCR-198
– DPC mode		0 (single)		TCR-199
– CHOICE mode		FDD		TCR-200
– Power offset PPilot-DPDCH		0		TCR-201
– DL rate matching restriction information		Not Present		TCR-202
– Spreading factor		Reference to clause 6.10 Parameter Set		TCR-203
– Fixed or Flexible Position		Reference to clause 6.10 Parameter Set		TCR-204
– TFCI existence		Reference to clause 6.10 Parameter Set		TCR-205
– CHOICE SF		Reference to clause 6.10 Parameter Set		TCR-206
– DPCH compressed mode info		Not Present		TCR-207
– TX Diversity mode		None		TCR-208
– SSDT information		Not Present	R99 and Rel-4 only	TCR-209
– Default DPCH Offset Value		Not Present		TCR-210
– MAC-hs reset indicator		Not Present	Rel-5	TCR-211
Downlink information common for all radio links	A4			TCR-212
– Downlink DPCH info common for all RL				TCR-213
– Timing indicator		Initialize		TCR-214
– CFN-targetSFN frame offset		Not Present		TCR-215
– Downlink DPCH power control information				TCR-216
– DPC mode		0 (single)		TCR-217
– CHOICE mode		FDD		TCR-218
– Power offset PPilot-DPDCH		0		TCR-219
– DL rate matching restriction information		Not Present		TCR-220
– Spreading factor		Reference to clause 6.10 Parameter Set		TCR-221
– Fixed or Flexible Position		Reference to clause 6.10 Parameter Set		TCR-222
– TFCI existence		Reference to clause 6.10 Parameter Set		TCR-223
– CHOICE SF		Reference to clause 6.10 Parameter Set		TCR-224
– DPCH compressed mode info		Not Present		TCR-225
– TX Diversity mode		None		TCR-226
– SSDT information		Not Present	R99 and Rel-4 only	TCR-227
– Default DPCH Offset Value		Arbitrary set to value 0..306688 by step of 512		TCR-228
– MAC-hs reset indicator		Not Present	Rel-5	TCR-229
Downlink information for each radio link list	A1, A2, A3			TCR-230
– Downlink information for each radio links				TCR-231
– CHOICE mode		FDD		TCR-232
– Primary CPICH info				TCR-233
– Primary scrambling code		Ref. to the Default setting in clause 6.1 (FDD)		TCR-234
– PDSCH with SHO DCH info		Not Present	R99 and Rel-4 only	TCR-235
– PDSCH code mapping		Not Present	R99 and Rel-4 only	TCR-236
– Serving HS-DSCH radio link indicator		FALSE	Rel-5	TCR-237
– Serving E-DCH radio link indicator		FALSE	Rel-6	TCR-238
– Downlink DPCH info for each RL				TCR-239
– Primary CPICH usage for channel estimation		Primary CPICH may be used		TCR-240
– DPCH frame offset		Set to value Default DPCH Offset Value ( as currently stored in SS) mod 38 400		TCR-241
– Power offset PPilot-DPDCH		0		TCR-242
– Secondary CPICH info		Not Present		TCR-243
– DL channelisation code				TCR-244
– Secondary scrambling code		4		TCR-245
– Spreading factor		Reference to clause 6.10 Parameter Set		TCR-246
– Code number		0		TCR-247
– Scrambling code change		Set to value Default1: No code change (if the UE has a compressed mode pattern sequence configured in variable TGPS_IDENTITY or included in the message including IE "Downlink DPCH info for each RL", which is using compressed mode method "SF/2") Set to value Default2: OMIT (otherwise)		TCR-248
– TPC combination index		0		TCR-249
– SSDT Cell Identity		Not Present	R99 and Rel-4 only	TCR-250
– Closed loop timing adjustment mode		Not Present		TCR-251
– E-AGCH Info		Not Present	Rel-6	TCR-252
– E-HICH Information		Not Present	Rel-6	TCR-253
– E-RGCH Information		Not Present	Rel-6	TCR-254
– SCCPCH information for FACH		Not Present	R99 and Rel-4 only	TCR-255
Downlink information for each radio link list	A4			TCR-256
– Downlink information for each radio link				TCR-257
– CHOICE mode		FDD		TCR-258
– Primary CPICH info				TCR-259
– Primary scrambling code		Ref. to the Default setting in clause 6.1 (FDD)		TCR-260
– PDSCH with SHO DCH info		Not Present	R99 and Rel-4 only	TCR-261
– PDSCH code mapping		Not Present	R99 and Rel-4 only	TCR-262
– Serving HS-DSCH radio link indicator		FALSE	Rel-5	TCR-263
– Serving E-DCH radio link indicator		FALSE	Rel-6	TCR-264
– Downlink DPCH info for each RL				TCR-265
– Primary CPICH usage for channel estimation		Primary CPICH may be used		TCR-266
– DPCH frame offset		Set to value: Default DPCH Offset Value mod 38 400		TCR-267
– Power offset PPilot-DPDCH		0		TCR-268
– Secondary CPICH info		Not Present		TCR-269
– DL channelisation code				TCR-270
– Secondary scrambling code		4		TCR-271
– Spreading factor		Reference to clause 6.10 Parameter Set		TCR-272
– Code number		0		TCR-273
– Scrambling code change		Set to value Default1: No code change (if the UE has a compressed mode pattern sequence configured in variable TGPS_IDENTITY or included in the message including IE "Downlink DPCH info for each RL", which is using compressed mode method "SF/2") Set to value Default2: OMIT (otherwise)		TCR-274
– TPC combination index		0		TCR-275
– SSDT Cell Identity		Not Present	R99 and Rel-4 only	TCR-276
– Closed loop timing adjustment mode		Not Present		TCR-277
– E-AGCH Info		Not Present	Rel-6	TCR-278
– E-HICH Information		Not Present	Rel-6	TCR-279
– E-RGCH Information		Not Present	Rel-6	TCR-280
– SCCPCH information for FACH		Not Present	R99 and Rel-4 only	TCR-281
– Downlink information for each radio link	A5			TCR-282
– Choice mode		FDD		TCR-283
– Primary CPICH info				TCR-284
– Primary scrambling code		Ref. to the Default setting in clause 6.1 (FDD)		TCR-285
– PDSCH with SHO DCH info		Not Present	R99 and Rel-4 only	TCR-286
– PDSCH code mapping		Not Present	R99 and Rel-4 only	TCR-287
– Serving HS-DSCH radio link indicator		FALSE	Rel-5	TCR-288
– Serving E-DCH radio link indicator		FALSE	Rel-6	TCR-289
– Downlink DPCH info for each RL		Not present		TCR-290
– E-AGCH Info		Not Present	Rel-6	TCR-291
– E-HICH Information		Not Present	Rel-6	TCR-292
– E-RGCH Information		Not Present	Rel-6	TCR-293
– SCCPCH information for FACH		Not Present	R99 and Rel-4 only	TCR-294
– Downlink information for each radio link	A6	Not Present		TCR-295
MBMS PL Service Restriction Information	A1, A2, A3, A4, A5, A6	Not Present	Rel-6	TCR-296

Condition	Explanation
A1	This IE need for "Non speech in CS"
A2	This IE need for "Speech in CS"
A3	This IE need for "Packet to CELL_DCH from CELL_DCH in PS"
A4	This IE need for "Packet to CELL_DCH from CELL_FACH in PS"
A5	This IE need for "Packet to CELL_FACH from CELL_DCH in PS"
A6	This IE need for "Packet to CELL_FACH from CELL_FACH in PS"

Contents of TRANSPORT CHANNEL RECONFIGURATION COMPLETE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if the value is identical to the same IE in the downlink TRANSPORT CHANNEL RECONFIGURATION message
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Uplink integrity protection activation info	Not checked
CHOICE mode	FDD
Deferred measurement control reading	Not present for Rel-7 or later, otherwise Not checked
COUNT-C activation time	Not checked
Radio bearer uplink ciphering activation time info	Not checked
Uplink counter synchronization info	Not present

Contents of TRANSPORT CHANNEL RECONFIGURATION FAILURE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if it is set to identical value of the same IE in the downlink TRANSPORT CHANNEL RECONFIGURATION message.
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Failure cause	Checked to see if it meets test requirement

Contents of TRANSPORT FORMAT COMBINATION CONTROL message: AM or UM (in CELL_DCH)

Information Element	Value/remark
Message Type
RRC transaction identifier	Arbitrarily selects an integer between 0 and 3
Integrity check info
– Message authentication code	SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	SS provides the value of this IE, from its internal counter.
CHOICE mode	FDD
DPCH/PUSCH TFCS in Uplink
– CHOICE Subset representation	Allowed transport format combination list
– Allowed Transport format combination	0 (The TFC is constructed from ALL TF0)
Activation time for TFC subset	Not Present
TFC Control duration	Not Present

Contents of TRANSPORT FORMAT COMBINATION CONTROL FAILURE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if it is set to identical value of the same IE in the downlink TRANSPORT CHANNEL RECONFIGURATION message.
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Failure cause	Checked to see if it meets test requirement

Contents of UE CAPABILITY ENQUIRY message: AM or UM

Information Element	Value/remark
Message Type
RRC transaction identifier	Arbitrarily selects an integer between 0 and 3
Integrity check info
– Message authentication code	SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	SS provides the value of this IE, from its internal counter.
Capability update requirement
– UE radio access FDD capability update requirement	TRUE
– UE radio access TDD capability update requirement	FALSE
– System specific capability update requirement list	Not Present

Contents of UE CAPABILITY INFORMATION message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if the value is identical to the same IE in the downlink UE CAPABILITY ENQUIRY message.
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
UE radio access capability	Value will be checked. Stated capability must be compatible with 3GPP TS 34.123-2 [3] (ICS statements) and the user settings
– Access stratum release indicator
– PDCP Capability
– RLC Capability
– Transport channel capability
– RF Capability FDD
– RF Capability TDD
– Physical channel capability
– UE multi-mode/multi-RAT capability
– Security Capability
– UE positioning Capability
– Measurement capability
UE radio access capability extension	Value will be checked. Stated capability must be compatible with 3GPP TS 34.123-2 [3] (ICS statements) and the user settings
UE system specific capability	Not Checked

Contents of UE CAPABILITY INFORMATION CONFIRM message: AM or UM

Information Element	Value/remark
Message Type
RRC transaction identifier	Set to the same value as received in the UE CAPABILITY INFORMATON message.
Integrity check info
– Message authentication code	SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	SS provides the value of this IE, from its internal counter.

Contents of UE INFORMATION REQUEST: AM

Information Element	Condition	Value/remark	Version
Message Type			Rel-10
RRC transaction identifier		Arbitrarily selects an integer between 0 and 3	Rel-10
Integrity check info			Rel-10
– message authentication code		SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC message sequence number		SS provides the value of this IE, from its internal counter.
Logged Measurements Report Request	A1	Not Present	Rel-10
Logged ANR Report Request	A1	TRUE	Rel-10

Condition	Explanation	Version
A1	Configuring of IE for requesting Logged ANR Report	Rel-10

Contents of UE INFORMATION RESPONSE: AM

Information Element	Value/remark	Version
Message Type		Rel-10
RRC transaction identifier	Arbitrarily selects an integer between 0 and 3	Rel-10
Integrity check info		Rel-10
– message authentication code	SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC message sequence number	SS provides the value of this IE, from its internal counter.
Logged Meas Report	Not Checked	Rel-10
Logged ANR Report Info	Not Checked	Rel-10

Contents of URA UPDATE message: TM

Information Element	Value/remark	Version
Message Type
U-RNTI
– SRNC identity	0000 0000 0001B
– S-RNTI	0000 0000 0000 0000 0001B
RRC transaction identifier	Checked to see if it is absent
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
URA update cause	See the test content
Protocol error indicator	Checked to see if it is absent or set to ‘FALSE’
HS-PDSCH in CELL_PCH and URA_PCH	Not checked
HS-PDSCH in CELL_FACH	Not checked
Protocol error information	Checked to see if it is absent
Logged Meas Available	Not checked	Rel-10

Contents of URA UPDATE CONFIRM message: UM

Information Element	Value/remark	Version
Message Type
U-RNTI	If this message is sent on CCCH, use the following values. Else, this IE is absent.
– SRNC identity	0000 0000 0001B
– S-RNTI	0000 0000 0000 0000 0001B
RRC transaction identifier	Arbitrarily selects and integer between 0 and 3
Integrity check info
– message authentication code	SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC message sequence number	SS provides the value of this IE, from its internal counter.
Integrity protection mode info	Not Present
Ciphering mode info	Not Present
New U-RNTI	Not Present
New C-RNTI	Not Present
RRC state indicator	URA_PCH
UTRAN DRX cycle length coefficient	3
CN information info	Not Present
URA identity	Not Present
RNC support for change of UE capability	Not Present
Downlink counter synchronization info	Not Present
Logged Meas Available	Not Present	Rel-10
ANR Logging Results Available	Not Present	Rel-10

Contents of UPLINK DIRECT TRANSFER message: AM

Information Element	Value/remark
Message Type
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.

CN domain identity	Checked to see if set to a CN domain for which a signalling connection exists
NAS message	Set according to that indicated in specific message content clause
Measured results on RACH	Not checked

Contents of UTRAN MOBILITY INFORMATION message: AM or UM

Information Element	Condition	Value/remark
Message Type
Integrity check info
– message authentication code		SS calculates the value of MAC-I for this message and writes to this IE. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC message sequence number		SS provides the value of this IE, from its internal counter.
RRC transaction identifier		Arbitrarily selects an integer between 0 and 3
Integrity protection mode info		Not Present
Ciphering mode info		Not Present
New U-RNTI		See the test content
New C-RNTI		See the test content
New H-RNTI		Not Present
UE Timers and constants in connected mode
– T301		2 000 milliseconds
– N301		2
– T302		4 000 milliseconds
– N302		3
– T304		1 000 milliseconds
– N304		3
– T305		60 minutes
– T307		50 seconds
– T308		320 milliseconds
– T309		8 seconds
– T310		320 milliseconds
– N310		5
– T311		500 milliseconds
– T312		5 seconds
– N312		200
– T313		10 seconds
– N313		200
– T314		20 seconds
– T315		30 seconds
– N315		200
– T316		50 seconds
– T317		1 800 seconds
CN information info		Not Present
URA identity		Not present
RNC support for change of UE capability		Not Present
Downlink counter synchronization info		Not Present
Dedicated WLAN Offload Information	WLAN
– CHOICE Configuration info		New configuration
– T330		10
– WLAN Offload Information
– WLAN Offload Configuration
-Threshold Serving RSCP	RSCP
-ThreshservingOffloadWLAN, low		Set according to specific message content
-ThreshservingOffloadWLAN, high		Set according to specific message content
-Threshold Serving Ec/N0	Ec/No
-ThreshservingOffloadWLAN, low2		Set according to specific message content
-ThreshservingOffloadWLAN, high2		Set according to specific message content
-Threshold Channel Utilization	ChannelUtilization
-ThreshchUtilWLAN, low		Set according to specific message content
-ThreshchUtilWLAN, high		Set according to specific message content
-Threshold Backhaul Bandwidth	BackHaul
-ThreshbackhRateDLWLAN, low		Set according to specific message content
-ThreshbackhRateDLWLAN, high		Set according to specific message content
-ThreshbackhRateULWLAN, low		Set according to specific message content
-ThreshbackhRateULWLAN, high		Set according to specific message content
-Threshold Beacon RSSI	RSSI
-ThreshBeaconRSSIWLAN, low		Set according to specific message content
-ThreshBeaconRSSIWLAN, high		Set according to specific message content
-Offload Preference Indicator		‘1111 1111 1111 1111’B
-TsteeringWLAN		0
-WLAN Identifier List		Only 1 WLAN identifier bradcasted
– WLAN Identifier
– WLAN Type ID
– SSID		Set as per Table 4.4.8-1 of 36.508[45]
-BSSID		Not Present
-HESSID		Not Present

Condition	Explanation
WLAN	RAN Assisted WLAN interworking test cases
RSCP	RSCP based thresholds are to be used
Ec/No	Ec/No based thresholds are to be used
ChannelUtilization	Channel Utilization based thresholds are to be used
BackHaul	BackHaul Bandwidth based thresholds are to be used
RSSI	Beacon RSSI based thresholds are to be used

Contents of UTRAN MOBILITY INFORMATION CONFIRM message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if it matches the value of the same IE in downlink UTRAN MOBILITY INFORMATION message
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Uplink integrity protection activation info	Not checked
Deferred measurement control reading	Not Present for Rel-7 or later, otherwise Not checked
COUNT-C activation time	Not checked
Radio bearer uplink ciphering activation time info	Not checked
Uplink counter synchronization info	Not present

Contents of UTRAN MOBILITY INFORMATION FAILURE message: AM

Information Element	Value/remark
Message Type
RRC transaction identifier	Checked to see if it matches the value of the same IE in downlink UTRAN MOBILITY INFORMATION message
Integrity check info
– Message authentication code	This IE is checked to see if it is present. The value is compared against the XMAC-I value computed by SS. The first/ leftmost bit of the bit string contains the most significant bit of the MAC-I.
– RRC Message sequence number	This IE is checked to see if it is present. The value is used by SS to compute the XMAC-I value.
Failure Cause	Checked to see if it meets test requirement