7.5 Test procedures for A-GPS and A-GNSS Performance requirements testing
34.1083GPPCommon test environments for User Equipment (UE)Conformance testingRelease 15TS
This clause specifies the procedures that shall be used for testing of A-GPS and A-GNSS Performance requirements in TS 37.571-1 [47] clauses 5 and 6.
7.5.1 Normal UE based A-GPS procedure
The procedure in this clause shall be used for all UE-based A-GPS TTFF test cases in CELL_DCH and CELL_FACH state as specified in TS 37.571-1 [47] clause 5.
7.5.1.1 Initial conditions
User Equipment:
The UE is in CELL_DCH or CELL_FACH state after executing the procedure defined in clause F.2 of TS 37.571-1 [47].
7.5.1.2 Procedure
|
Step |
Direction |
Message |
Comments |
|
|---|---|---|---|---|
|
UE |
SS |
|||
|
1 |
|
RESET UE POSITIONING STORED INFORMATION |
TC |
|
|
2 |
|
RRC MEASUREMENT CONTROL |
RRC (Setup, No Reporting, Nav model Satellites 1, 2, 3, 4, 5 (1)) |
|
|
3 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, No Reporting, Nav model Satellites 6, 7, 8, 9 (1), Iono Model) |
|
|
4 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, Periodical Reporting Criterion, GPS Ref time (1), ReferencePosition (1)) |
|
|
5 |
|
RRC MEASUREMENT REPORT |
RRC (Position Estimate), 1st test instance |
|
|
6 |
|
RESET UE POSITIONING STORED INFORMATION |
TC |
|
|
7 |
|
RRC MEASUREMENT CONTROL |
RRC (Setup, No Reporting, Nav model Satellites 1, 2, 3, 4,5 (2)) |
|
|
8 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, No Reporting, Nav model Satellites 6, 7, 8, 9 (2), Iono Model) |
|
|
9 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, Periodical Reporting Criterion, GPS Ref time (2), ReferencePosition (2)) |
|
|
10 |
|
RRC MEASUREMENT REPORT |
RRC (Position Estimate), 2nd test instance |
|
|
11 |
|
RESET UE POSITIONING STORED INFORMATION |
TC |
|
|
…. |
…… |
……. |
||
|
n |
|
RRC MEASUREMENT REPORT |
RRC (Position Estimate), nth test instance |
|
7.5.1.3 Specific message contents
Contents of RESET UE POSITIONING STORED INFORMATION message: TC
|
Information Element |
Value/remark |
|
UE Positioning Technology |
AGPS |
Contents of MEASUREMENT CONTROL messages: RRC
MEASUREMENT CONTROL (Steps 2 + (n-1)*5):
|
Information element |
Value/remark |
Version |
|
Measurement Information Elements |
||
|
Measurement Identity |
10 |
|
|
Measurement Command |
Setup |
|
|
Measurement Reporting Mode |
||
|
– Measurement report transfer mode |
Acknowledged mode RLC |
|
|
– Periodical reporting / Event trigger reporting mode |
Periodical reporting |
|
|
Additional Measurements List |
Not present |
|
|
CHOICE Measurement type |
UE positioning measurement |
|
|
– UE positioning measurement |
||
|
– UE positioning reporting quantity |
||
|
– Method type |
UE based |
|
|
– Positioning methods |
GPS |
|
|
– Response time |
128 |
R99 only |
|
– Horizontal accuracy |
19 (51 m) |
|
|
– Vertical accuracy |
48 (102 m) |
|
|
– GPS timing of cell wanted |
FALSE |
|
|
– Multiple sets |
FALSE |
R99 only |
|
– Additional assistance data request |
FALSE |
|
|
– Environmental characterization |
Not present |
|
|
– Measurement validity |
||
|
– UE state |
All states |
|
|
– CHOICE Reporting criteria |
||
|
– No reporting |
||
|
– UE pos OTDOA assistance data for UE-assisted |
Not present |
|
|
– UE pos OTDOA assistance data for UE-based |
Not present |
|
|
– UE positioning GPS assistance data |
||
|
– UE positioning GPS navigation model |
Satellites 1-5 as specified in TS 37.571-5 [48] clause 5.2 |
|
|
Physical Channel Information Elements |
||
|
DPCH compressed mode status info |
Not present |
MEASUREMENT CONTROL (Steps 3 + (n-1)*5):
|
Information element |
Value/remark |
Version |
|
Measurement Information Elements |
||
|
Measurement Identity |
10 |
|
|
Measurement Command |
Modify |
|
|
Measurement Reporting Mode |
||
|
– Measurement report transfer mode |
Acknowledged mode RLC |
|
|
– Periodical reporting / Event trigger reporting mode |
Periodical reporting |
|
|
Additional Measurements List |
Not present |
|
|
CHOICE Measurement type |
UE positioning measurement |
|
|
– UE positioning measurement |
||
|
– UE positioning reporting quantity |
||
|
– Method type |
UE based |
|
|
– Positioning methods |
GPS |
|
|
– Response time |
128 |
R99 only |
|
– Horizontal accuracy |
19 (51 m) |
|
|
– Vertical accuracy |
48 (102 m) |
|
|
– GPS timing of cell wanted |
FALSE |
|
|
– Multiple sets |
FALSE |
R99 only |
|
– Additional assistance data request |
FALSE |
|
|
– Environmental characterization |
Not present |
|
|
– Measurement validity |
||
|
– UE state |
All states |
|
|
– CHOICE Reporting criteria |
||
|
– No reporting |
||
|
– UE pos OTDOA assistance data for UE-assisted |
Not present |
|
|
– UE pos OTDOA assistance data for UE-based |
Not present |
|
|
– UE positioning GPS assistance data |
||
|
– UE positioning GPS navigation model |
Satellites 6-9 as specified in TS 37.571-5 [48] clause 5.2 |
|
|
– UE positioning GPS ionospheric model |
As specified in TS 37.571-5 [48] clause 5.2 |
|
|
Physical Channel Information Elements |
||
|
DPCH compressed mode status info |
Not present |
MEASUREMENT CONTROL (Steps 4 + (n-1)*5):
|
Information element |
Value/remark |
Version |
|
Measurement Information Elements |
||
|
Measurement Identity |
10 |
|
|
Measurement Command |
Modify |
|
|
Measurement Reporting Mode |
||
|
– Measurement report transfer mode |
Acknowledged mode RLC |
|
|
– Periodical reporting / Event trigger reporting mode |
Periodical reporting |
|
|
Additional Measurements List |
Not present |
|
|
CHOICE Measurement type |
UE positioning measurement |
|
|
– UE positioning measurement |
||
|
– UE positioning reporting quantity |
||
|
– Method type |
UE based |
|
|
– Positioning methods |
GPS |
|
|
– Response time |
128 |
R99 only |
|
– Horizontal accuracy |
19 (51 m) |
|
|
– Vertical accuracy |
48 (102 m) |
|
|
– GPS timing of cell wanted |
FALSE |
|
|
– Multiple sets |
FALSE |
R99 only |
|
– Additional assistance data request |
FALSE |
|
|
– Environmental characterization |
Not present |
|
|
– Measurement validity |
||
|
– UE state |
All states |
|
|
– CHOICE Reporting criteria |
Periodical Reporting Criteria |
|
|
– Amount of reporting |
1 |
|
|
– Reporting Interval |
20000 |
|
|
– UE pos OTDOA assistance data for UE-assisted |
Not present |
|
|
– UE pos OTDOA assistance data for UE-based |
Not present |
|
|
– UE positioning GPS assistance data |
||
|
– UE positioning GPS reference time |
As specified in TS 37.571-5 [48] clause 5.2 |
|
|
– UE positioning GPS reference UE position |
As specified in TS 37.571-5 [48] clause 5.2 |
|
|
Physical Channel Information Elements |
||
|
DPCH compressed mode status info |
Not present |
7.5.2 UE based A-GPS procedure for moving scenario and periodic update test case
The procedure in this clause shall be used for the UE-based A-GPS moving scenario and periodic update test case in CELL_DCH and CELL_FACH state as specified in TS 37.571-1 [47] clause 5.
7.5.2.1 Initial conditions
User Equipment:
The UE is in CELL_DCH or CELL_FACH state after executing the procedure defined in clause F.2 of TS 37.571-1 [47].
7.5.2.2 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
RESET UE POSITIONING STORED INFORMATION |
TC |
|
|
2 |
|
RRC MEASUREMENT CONTROL |
RRC (Setup, No Reporting, Nav model Satellites 1, 2, 3, 4, 5) |
|
|
3 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, No Reporting, Nav model Satellites 6, 7, 8, 9, Iono Model) |
|
|
4 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, Periodical Reporting Criterion, GPS Ref time, ReferencePosition) |
|
|
5 |
|
RRC MEASUREMENT REPORT |
RRC (Position Estimate) |
|
|
6 |
|
RRC MEASUREMENT REPORT |
RRC (Position Estimate) |
|
|
….. |
|
…… |
||
|
n |
|
RRC MEASUREMENT REPORT |
RRC (Position Estimate) |
|
|
NOTE: In the actual testing the UE may report error messages at step 5 until it has been able to acquire a position estimate. |
||||
7.5.2.3 Specific message contents
Contents of RESET UE POSITIONING STORED INFORMATION message: TC
The contents of the Reset UE Positioning Stored Information message in Step 1 are the same as specified for Normal UE based A-GPS testing in clause 7.5.1.
Contents of MEASUREMENT CONTROL message: RRC
The contents of the Measurement Control message in steps 2 and 3 are the same as specified for Normal UE based A-GPS testing in clause 7.5.1.
The contents of the Measurement Control message in step 4 are the same as specified for Normal UE based A-GPS testing in clause 7.5.1 with the following exceptions:
|
Information Element |
Value/remark |
|
Amount of reporting |
Infinite (see note) |
|
Reporting interval |
2 000 ms |
|
NOTE: Infinite means during the complete test time. |
|
7.5.3 Void
7.5.4 Normal UE assisted GPS procedure
The procedure in this clause shall be used for all UE-assisted A-GPS TTFF test cases in CELL_DCH and CELL_FACH state as specified in TS 37.571-1 [47] clause 5.
7.5.4.1 Initial conditions
User Equipment:
The UE is in CELL_DCH or CELL_FACH state after executing the procedure defined in clause F.2 of TS 37.571-1 [47].
7.5.4.2 Procedure
|
Step |
Direction |
Message |
Comments |
|
|---|---|---|---|---|
|
UE |
SS |
|||
|
1 |
|
RESET UE POSITIONING STORED INFORMATION |
TC |
|
|
2 |
|
RRC MEASUREMENT CONTROL |
RRC (Setup, Periodical Reporting Criteria, GPS Ref time) |
|
|
3 |
|
RRC MEASUREMENT REPORT |
RRC (Additional Assistance Data Request) |
|
|
4 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, No Reporting, Assistance Data Satellites 1, 2, 3, 4, 5, 6, 7, 8, 9) |
|
|
5 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, Periodical Reporting Criteria) |
|
|
6 |
|
RRC MEASUREMENT REPORT |
RRC (GPS Measured Results), 1st test instance |
|
|
7 |
|
RESET UE POSITIONING STORED INFORMATION |
TC |
|
|
8 |
|
RRC MEASUREMENT CONTROL |
RRC (Setup, Periodical Reporting Criteria, GPS Ref time) |
|
|
9 |
|
RRC MEASUREMENT REPORT |
RRC (Additional Assistance Data Request) |
|
|
10 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, No Reporting, Assistance Data Satellites 1, 2, 3, 4, 5, 6, 7, 8, 9) |
|
|
11 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, Periodical Reporting Criteria) |
|
|
12 |
|
RRC MEASUREMENT REPORT |
RRC (GPS Measured Results), 2nd test instance |
|
|
13 |
|
RESET UE POSITIONING STORED INFORMATION |
TC |
|
|
…. |
…… |
……. |
||
|
n |
|
RRC MEASUREMENT REPORT |
RRC (GPS Measured Results), nth test instance |
|
7.5.4.3 Specific message contents
Contents of RESET UE POSITIONING STORED INFORMATION message: TC
|
Information Element |
Value/remark |
|
UE Positioning Technology |
AGPS |
Contents of MEASUREMENT CONTROL messages: RRC
MEASUREMENT CONTROL (Steps 2 + (n-1)*6):
|
Information element |
Value/remark |
Version |
|
Measurement Information Elements |
||
|
Measurement Identity |
10 |
|
|
Measurement Command |
Setup |
|
|
Measurement Reporting Mode |
||
|
– Measurement report transfer mode |
Acknowledged mode RLC |
|
|
– Periodical reporting / Event trigger reporting mode |
Periodical reporting |
|
|
Additional Measurements List |
Not present |
|
|
CHOICE Measurement type |
UE positioning measurement |
|
|
– UE positioning measurement |
||
|
– UE positioning reporting quantity |
||
|
– Method type |
UE assisted |
|
|
– Positioning methods |
GPS |
|
|
– Response time |
128 |
R99 only |
|
– Horizontal accuracy |
19 (51 m) |
|
|
– Vertical accuracy |
48 (102 m) |
|
|
– GPS timing of cell wanted |
FALSE |
|
|
– Multiple sets |
FALSE |
R99 only |
|
– Additional assistance data request |
TRUE |
|
|
– Environmental characterization |
Not present |
|
|
– Measurement validity |
||
|
– UE state |
All states |
|
|
– CHOICE Reporting criteria |
Periodical Reporting Criteria |
|
|
– Amount of reporting |
1 |
|
|
– Reporting Interval |
20000 |
|
|
– UE pos OTDOA assistance data for UE-assisted |
Not present |
|
|
– UE pos OTDOA assistance data for UE-based |
Not present |
|
|
– UE positioning GPS assistance data |
||
|
– UE positioning GPS reference time |
As specified in TS 37.571-5 [48] clause 5.2 |
|
|
Physical Channel Information Elements |
||
|
DPCH compressed mode status info |
Not present |
MEASUREMENT REPORT (Steps 3 + (n-1)*6):
|
Information element |
Value/remark |
Version |
|
Measurement Information Elements |
||
|
Measurement Identity |
10 |
|
|
Measured Results |
||
|
– CHOICE Measurement |
||
|
– UE positioning measured results |
||
|
– UE positioning OTDOA measured results |
Not present |
|
|
– UE positioning position estimate info |
Not present |
|
|
– UE positioning GPS measured results |
Not present |
|
|
– UE positioning error |
||
|
– Error reason |
Assistance Data Missing |
|
|
– GPS additional assistance data request |
Defines assistance data requested by the UE |
|
|
Measured Results on RACH |
Not present |
|
|
Additional Measured Results |
Not present |
|
|
Event Results |
Not present |
MEASUREMENT CONTROL (Steps 4 + (n-1)*6):
|
Information element |
Value/remark |
Version |
|
Measurement Information Elements |
||
|
Measurement Identity |
10 |
|
|
Measurement Command |
Modify |
|
|
Measurement Reporting Mode |
||
|
– Measurement report transfer mode |
Acknowledged mode RLC |
|
|
– Periodical reporting / Event trigger reporting mode |
Periodical reporting |
|
|
Additional Measurements List |
Not present |
|
|
CHOICE Measurement type |
UE positioning measurement |
|
|
– UE positioning measurement |
||
|
– UE positioning reporting quantity |
||
|
– Method type |
UE assisted |
|
|
– Positioning methods |
GPS |
|
|
– Response time |
128 |
R99 only |
|
– Horizontal accuracy |
19 (51 m) |
|
|
– Vertical accuracy |
48 (102 m) |
|
|
– GPS timing of cell wanted |
FALSE |
|
|
– Multiple sets |
FALSE |
R99 only |
|
– Additional assistance data request |
FALSE |
|
|
– Environmental characterization |
Not present |
|
|
– Measurement validity |
||
|
– UE state |
All states |
|
|
– CHOICE Reporting criteria |
||
|
– No reporting |
||
|
– UE pos OTDOA assistance data for UE-assisted |
Not present |
|
|
– UE pos OTDOA assistance data for UE-based |
Not present |
|
|
– UE positioning GPS assistance data |
As specified in TS 37.571-5 [48] clause 5.2 and requested by the UE in Step 3+(n-1)*6 |
|
|
Physical Channel Information Elements |
||
|
DPCH compressed mode status info |
Not present |
MEASUREMENT CONTROL (Steps 5 + (n-1)*6):
|
Information element |
Value/remark |
Version |
|
Measurement Information Elements |
||
|
Measurement Identity |
10 |
|
|
Measurement Command |
Modify |
|
|
Measurement Reporting Mode |
||
|
– Measurement report transfer mode |
Acknowledged mode RLC |
|
|
– Periodical reporting / Event trigger reporting mode |
Periodical reporting |
|
|
Additional Measurements List |
Not present |
|
|
CHOICE Measurement type |
UE positioning measurement |
|
|
– UE positioning measurement |
||
|
– UE positioning reporting quantity |
||
|
– Method type |
UE assisted |
|
|
– Positioning methods |
GPS |
|
|
– Response time |
128 |
R99 only |
|
– Horizontal accuracy |
19 (51 m) |
|
|
– Vertical accuracy |
48 (102 m) |
|
|
– GPS timing of cell wanted |
FALSE |
|
|
– Multiple sets |
FALSE |
R99 only |
|
– Additional assistance data request |
FALSE |
|
|
– Environmental characterization |
Not present |
|
|
– Measurement validity |
||
|
– UE state |
All states |
|
|
– CHOICE Reporting criteria |
Periodical Reporting Criteria |
|
|
– Amount of reporting |
1 |
|
|
– Reporting Interval |
20000 |
|
|
– UE pos OTDOA assistance data for UE-assisted |
Not present |
|
|
– UE pos OTDOA assistance data for UE-based |
Not present |
|
|
– UE positioning GPS assistance data |
Not present |
|
|
Physical Channel Information Elements |
||
|
DPCH compressed mode status info |
Not present |
7.5.5 UE assisted A-GPS procedure for moving scenario and periodic update test case
The procedure in this clause shall be used for the UE-assisted A-GPS moving scenario and periodic update test case in CELL_DCH and CELL_FACH state as specified in TS 37.571-1 [47] clause 5.
7.5.5.1 Initial conditions
User Equipment:
The UE is in CELL_DCH or CELL_FACH state after executing the procedure defined in clause F.2 of TS 37.571-1 [47].
7.5.5.2 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
RESET UE POSITIONING STORED INFORMATION |
TC |
|
|
2 |
|
RRC MEASUREMENT CONTROL |
RRC (Setup, Periodical Reporting Criteria, GPS Ref time) |
|
|
3 |
|
RRC MEASUREMENT REPORT |
RRC (Additional Assistance Data Request) |
|
|
4 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, No Reporting, Assistance Data Satellites 1, 2, 3, 4, 5, 6, 7, 8, 9) |
|
|
5 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, Periodical Reporting Criteria) |
|
|
6 |
|
RRC MEASUREMENT REPORT |
RRC (GPS Measured Results), 1st test instance |
|
|
7 |
|
RRC MEASUREMENT REPORT |
RRC (GPS Measured Results), 2nd test instance |
|
|
….. |
|
…… |
||
|
n |
|
RRC MEASUREMENT REPORT |
RRC (GPS Measured Results), nth test instance |
|
|
NOTE: In the actual testing the UE may report error messages at step 6 until it has been able to acquire GPS measured results. |
||||
7.5.5.3 Specific message contents
Contents of RESET UE POSITIONING STORED INFORMATION message: TC
The contents of the Reset UE Positioning Stored Information message in Step 1 are the same as specified for Normal UE assisted A-GPS testing in clause 7.5.4.
Contents of MEASUREMENT CONTROL message: RRC
The contents of the Measurement Control message in steps 2 and 4 are the same as specified for Normal UE assisted A-GPS testing in clause 7.5.4.
The contents of the Measurement Control message in step 5 are the same as specified for Normal UE assisted A-GPS testing in clause 7.5.4 with the following exceptions:
|
Information Element |
Value/remark |
|
Amount of reporting |
Infinite (see note) |
|
Reporting interval |
2 000 ms |
|
NOTE: Infinite means during the complete test time. |
|
7.5.6 Normal UE based A-GNSS procedure
The procedure in this clause shall be used for all UE-based A-GNSS TTFF test cases in CELL_DCH and CELL_FACH state as specified in TS 37.571-1 [47] clause 6.
7.5.6.1 Initial conditions
User Equipment:
The UE is in CELL_DCH or CELL_FACH state after executing the procedure defined in clause F.2 of TS 37.571-1 [47].
7.5.6.2 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
RESET UE POSITIONING STORED INFORMATION |
TC |
|
|
2 |
|
RRC MEASUREMENT CONTROL |
RRC (Setup, No Reporting, Nav model GPS Satellites 1, 2, 3, 4, 5 (1), Nav model GANSS Satellites 1, 2, 3, 4, 5 (1), Aux Info GANSS Satellites 1, 2, 3, 4, 5 (1)) |
|
|
3 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, No Reporting, Nav model GPS Satellites 6, 7, 8, 9 (1), Iono Model, Nav model GANSS Satellites 6,7,8 (1), Aux Info GANSS Satellites 6,7,8 (1)) |
|
|
4 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, Periodical Reporting Criterion, GPS Ref time (1), GPS Ref location (1), GPS UTC Model(1), GANSS Time Model (1)) |
|
|
5 |
|
RRC MEASUREMENT REPORT |
RRC (Position Estimate), 1st test Instance |
|
|
6 |
|
RESET UE POSITIONING STORED INFORMATION |
TC |
|
|
7 |
|
RRC MEASUREMENT CONTROL |
RRC (Setup, No Reporting, Nav model GPS Satellites 1, 2, 3, 4, 5 (2), Nav model GANSS Satellites 1, 2, 3, 4, 5 (2), Aux Info GANSS Satellites 1, 2, 3, 4, 5 (2)) |
|
|
8 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, No Reporting, Nav model GPS Satellites 6, 7, 8, 9 (2), Iono Model, Nav model GANSS Satellites 6,7,8 (2), Aux Info GANSS Satellites 6,7,8 (2)) |
|
|
9 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, Periodical Reporting Criterion, GPS Ref time (1), GPS Ref location (2), GPS UTC Model(1), GANSS Time Model (2)) |
|
|
10 |
|
RRC MEASUREMENT REPORT |
RRC (Position Estimate), 2nd test Instance |
|
|
11 |
|
RESET UE POSITIONING STORED INFORMATION |
TC |
|
|
….. |
|
…… |
||
|
n |
|
RRC MEASUREMENT REPORT |
RRC (Position Estimate), nth test Instance |
|
7.5.6.3 Specific message contents
Contents of RESET UE POSITIONING STORED INFORMATION message: TC
|
Information Element |
Value/remark |
|
UE Positioning Technology |
AGNSS |
Contents of MEASUREMENT CONTROL messages: RRC
MEASUREMENT CONTROL (Steps 2 + (n-1)*5):
|
Information element |
Value/remark |
Version |
|
Measurement Information Elements |
||
|
Measurement Identity |
10 |
|
|
Measurement Command |
Setup |
|
|
Measurement Reporting Mode |
||
|
– Measurement report transfer mode |
Acknowledged mode RLC |
|
|
– Periodical reporting / Event trigger reporting mode |
Periodical reporting |
|
|
Additional Measurements List |
Not present |
|
|
CHOICE Measurement type |
UE positioning measurement |
|
|
– UE positioning measurement |
||
|
– UE positioning reporting quantity |
||
|
– Method type |
UE based |
|
|
– Positioning methods |
GPS |
|
|
– Horizontal accuracy |
19 (51 m) |
|
|
– Vertical accuracy |
48 (102 m) |
|
|
– GPS timing of cell wanted |
FALSE |
|
|
– Additional assistance data request |
FALSE |
|
|
– Environmental characterization |
Not present |
|
|
– GANSSPositioningMethods |
Bitmap as per supported GNSS |
|
|
– Measurement validity |
||
|
– UE state |
All states |
|
|
– CHOICE Reporting criteria |
||
|
– No reporting |
||
|
– UE pos OTDOA assistance data for UE-assisted |
Not present |
|
|
– UE pos OTDOA assistance data for UE-based |
Not present |
|
|
– UE positioning GPS assistance data |
||
|
– UE positioning GPS navigation model |
GPS Satellites 1-5 as specified in TS 37.571-5 [48] clause 6.2 |
|
|
– UE positioning GANSS assistance data |
||
|
-GanssGenericDataList |
||
|
– UE positioning GANSS add navigation models |
GANSS Satellites 1-5 as specified in TS 37.571-5 [48] clause 6.2 |
|
|
– UE positioning GANSS AuxiliaryInfo |
GANSS Satellites 1-5 as specified in TS 37.571-5 [48] clause 6.2 |
|
|
Physical Channel Information Elements |
||
|
DPCH compressed mode status info |
Not present |
MEASUREMENT CONTROL (Steps 3 + (n-1)*5):
|
Information element |
Value/remark |
Version |
|
Measurement Information Elements |
||
|
Measurement Identity |
10 |
|
|
Measurement Command |
Modify |
|
|
Measurement Reporting Mode |
||
|
– Measurement report transfer mode |
Acknowledged mode RLC |
|
|
– Periodical reporting / Event trigger reporting mode |
Periodical reporting |
|
|
Additional Measurements List |
Not present |
|
|
CHOICE Measurement type |
UE positioning measurement |
|
|
– UE positioning measurement |
||
|
– UE positioning reporting quantity |
||
|
– Method type |
UE based |
|
|
– Positioning methods |
GPS |
|
|
– Horizontal accuracy |
19 (51 m) |
|
|
– Vertical accuracy |
48 (102 m) |
|
|
– GPS timing of cell wanted |
FALSE |
|
|
– Additional assistance data request |
FALSE |
|
|
– Environmental characterization |
Not present |
|
|
– GANSSPositioningMethods |
Bitmap as per supported GNSS |
|
|
– Measurement validity |
||
|
– UE state |
All states |
|
|
– CHOICE Reporting criteria |
||
|
– No reporting |
||
|
– UE pos OTDOA assistance data for UE-assisted |
Not present |
|
|
– UE pos OTDOA assistance data for UE-based |
Not present |
|
|
– UE positioning GPS assistance data |
||
|
– UE positioning GPS navigation model |
GPS Satellites 6-9 as specified in TS 37.571-5 [48] clause 6.2 |
|
|
– UE positioning GPS ionospheric model |
As specified in TS 37.571-5 [48] clause 6.2 |
|
|
– UE positioning GANSS assistance data |
||
|
-GanssGenericDataList |
||
|
– UE positioning GANSS add navigation models |
GANSS Satellites 6-8 as specified in TS 37.571-5 [48] clause 6.2 |
|
|
– UE positioning GANSS AuxiliaryInfo |
GANSS Satellites 6-8 as specified in TS 37.571-5 [48] clause 6.2 |
|
|
Physical Channel Information Elements |
||
|
DPCH compressed mode status info |
Not present |
MEASUREMENT CONTROL (Steps 4 + (n-1)*5):
|
Information element |
Value/remark |
Version |
|
Measurement Information Elements |
||
|
Measurement Identity |
10 |
|
|
Measurement Command |
Modify |
|
|
Measurement Reporting Mode |
||
|
– Measurement report transfer mode |
Acknowledged mode RLC |
|
|
– Periodical reporting / Event trigger reporting mode |
Periodical reporting |
|
|
Additional Measurements List |
Not present |
|
|
CHOICE Measurement type |
UE positioning measurement |
|
|
– UE positioning measurement |
||
|
– UE positioning reporting quantity |
||
|
– Method type |
UE based |
|
|
– Positioning methods |
GPS |
|
|
– Horizontal accuracy |
19 (51 m) |
|
|
– Vertical accuracy |
48 (102 m) |
|
|
– GPS timing of cell wanted |
FALSE |
|
|
– Additional assistance data request |
FALSE |
|
|
– Environmental characterization |
Not present |
|
|
– Measurement validity |
||
|
– UE state |
All states |
|
|
– CHOICE Reporting criteria |
Periodical Reporting Criteria |
|
|
– Amount of reporting |
1 |
|
|
– Reporting Interval |
20000 |
|
|
– UE pos OTDOA assistance data for UE-assisted |
Not present |
|
|
– UE pos OTDOA assistance data for UE-based |
Not present |
|
|
– UE positioning GPS assistance data |
||
|
– UE positioning GPS reference time |
As specified in TS 37.571-5 [48] clause 6.2 |
|
|
– UE positioning GPS reference UE position |
As specified in TS 37.571-5 [48] clause 6.2 |
|
|
– UE positioning GPS UTC model |
As specified in TS 37.571-5 [48] clause 6.2 |
|
|
– UE positioning GANSS assistance data |
||
|
-GanssGenericDataList |
||
|
– GANSS Time model list |
As specified in TS 37.571-5 [48] clause 6.2 |
|
|
Physical Channel Information Elements |
||
|
DPCH compressed mode status info |
Not present |
7.5.7 UE based A-GNSS procedure for moving scenario and periodic update test case
The procedure in this clause shall be used for the UE-based A-GNSS moving scenario and periodic update test case in CELL_DCH and CELL_FACH state as specified in TS 37.571-1 [47] clause 6.
7.5.7.1 Initial conditions
User Equipment:
The UE is in CELL_DCH or CELL_FACH state after executing the procedure defined in clause F.2 of TS 37.571-1 [47].
7.5.7.2 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
RESET UE POSITIONING STORED INFORMATION |
TC |
|
|
2 |
|
RRC MEASUREMENT CONTROL |
RRC (Setup, No Reporting, Nav model GPS Satellites 1, 2, 3, 4, 5, Nav model GANSS Satellites 1, 2, 3, 4, 5, Aux Info GANSS Satellites 1, 2, 3, 4, 5) |
|
|
3 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, No Reporting, Nav model GPS Satellites 6, 7, 8, 9, Iono Model, Nav model GANSS Satellites 6,7,8, Aux Info GANSS Satellites 6,7,8) |
|
|
4 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, Periodical Reporting Criterion, GPS Ref time, GPS Ref location, GPS UTC Model, GANSS Time Model) |
|
|
5 |
|
RRC MEASUREMENT REPORT |
RRC (Position Estimate) |
|
|
6 |
|
RRC MEASUREMENT REPORT |
RRC (Position Estimate) |
|
|
….. |
|
…… |
||
|
n |
|
RRC MEASUREMENT REPORT |
RRC (Position Estimate) |
|
|
NOTE: In the actual testing the UE may report error messages at step 5 until it has been able to acquire GPS measured results. |
||||
7.5.7.3 Specific message contents
Contents of RESET UE POSITIONING STORED INFORMATION message: TC
The contents of the Reset UE Positioning Stored Information message in Step 1 are the same as specified for Normal UE based A-GNSS testing in clause 7.5.6.
Contents of MEASUREMENT CONTROL message: RRC
The contents of the Measurement Control message in steps 2 and 3 are the same as specified for Normal UE based A-GNSS testing in clause 7.5.6.
The contents of the Measurement Control message in step 4 are the same as specified for Normal UE based A-GNSS testing in clause 7.5.6 with the following exceptions:
|
Information Element |
Value/remark |
|
Amount of reporting |
Infinite (see note) |
|
Reporting interval |
2 000 ms |
|
NOTE: Infinite means during the complete test time. |
|
7.5.8 Normal UE assisted A-GNSS procedure
The procedure in this clause shall be used for all UE-assisted A-GNSS TTFF test cases in CELL_DCH and CELL_FACH state as specified in TS 37.571-1 [47] clause 6.
7.5.8.1 Initial conditions
User Equipment:
The UE is in CELL_DCH or CELL_FACH state after executing the procedure defined in clause F.2 of TS 37.571-1 [47].
7.5.8.2 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
RESET UE POSITIONING STORED INFORMATION |
TC |
|
|
2 |
|
RRC MEASUREMENT CONTROL |
RRC (Setup, Periodical Reporting criteria, GPS Ref time, GPS UTC Model, GANSS Time Model) |
|
|
3 |
|
RRC MEASUREMENT REPORT |
RRC (Additional Assistance Data Request) |
|
|
4 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, No Reporting, Assistance Data GPS Satellites 1, 2, 3, 4, 5, 6, 7, 8, 9) |
|
|
5 |
|
RRC MEASUREMENT CONTROL |
RRC (Setup, Periodical Reporting criteria, Reference Measurement Info GANSS Satellites 1, 2, 3, 4, 5, 6, 7, 8 Aux Info GANSS Satellites 1, 2, 3, 4, 5, 6, 7, 8) |
|
|
6 |
|
RRC MEASUREMENT REPORT |
RRC (GNSS Measured Results), 1st test Instance |
|
|
7 |
|
RESET UE POSITIONING STORED INFORMATION |
TC |
|
|
8 |
|
RRC MEASUREMENT CONTROL |
RRC (Setup, Periodical Reporting criteria, GPS Ref time, GPS UTC Model, GANSS Time Model) |
|
|
9 |
|
RRC MEASUREMENT REPORT |
RRC (Additional Assistance Data Request) |
|
|
10 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, No Reporting, Assistance |
|
|
Data GPS Satellites 1, 2, 3, 4, 5, 6, 7, 8, 9) |
||||
|
11 |
|
RRC MEASUREMENT CONTROL |
RRC (Setup, Periodical Reporting criteria, Reference Measurement Info GANSS Satellites 1, 2, 3, 4, 5, 6, 7, 8 Aux Info GANSS Satellites 1, 2, 3, 4, 5, 6, 7, 8) |
|
|
12 |
|
RRC MEASUREMENT REPORT |
RRC (GNSS Measured Results), 2nd test Instance |
|
|
13 |
|
RESET UE POSITIONING STORED INFORMATION |
TC |
|
|
….. |
|
…… |
||
|
n |
|
RRC MEASUREMENT REPORT |
RRC (GNSS Measured Results), nth test Instance |
|
7.5.8.3 Specific message contents
Contents of RESET UE POSITIONING STORED INFORMATION message: TC
|
Information Element |
Value/remark |
|
UE Positioning Technology |
AGNSS |
Contents of MEASUREMENT CONTROL messages: RRC
MEASUREMENT CONTROL (Steps 2 + (n-1)*6):
|
Information element |
Value/remark |
Version |
|
Measurement Information Elements |
||
|
Measurement Identity |
10 |
|
|
Measurement Command |
Setup |
|
|
Measurement Reporting Mode |
||
|
– Measurement report transfer mode |
Acknowledged mode RLC |
|
|
– Periodical reporting / Event trigger reporting mode |
Periodical reporting |
|
|
Additional Measurements List |
Not present |
|
|
CHOICE Measurement type |
UE positioning measurement |
|
|
– UE positioning measurement |
||
|
– UE positioning reporting quantity |
||
|
– Method type |
UE assisted |
|
|
– Positioning methods |
GPS |
|
|
– Horizontal accuracy |
19 (51 m) |
|
|
– Vertical accuracy |
48 (102 m) |
|
|
– GPS timing of cell wanted |
FALSE |
|
|
– Additional assistance data request |
TRUE |
|
|
– Environmental characterization |
Not present |
|
|
– GANSSPositioningMethods |
Bitmap as per supported GNSS |
|
|
– Measurement validity |
||
|
– UE state |
All states |
|
|
– CHOICE Reporting criteria |
Periodical Reporting Criteria |
|
|
– Amount of reporting |
1 |
|
|
– Reporting Interval |
20000 |
|
|
– UE pos OTDOA assistance data for UE-assisted |
Not present |
|
|
– UE pos OTDOA assistance data for UE-based |
Not present |
|
|
– UE positioning GPS assistance data |
||
|
– UE positioning GPS reference time |
As specified in TS 37.571-5 [48] clause 6.2 |
|
|
– UE positioning GPS UTC model |
As specified in TS 37.571-5 [48] clause 6.2 |
|
|
– UE positioning GANSS assistance data |
||
|
-GanssGenericDataList |
||
|
– GANSS Time model list |
As specified in TS 37.571-5 [48] clause 6.2 |
|
|
Physical Channel Information Elements |
||
|
DPCH compressed mode status info |
Not present |
MEASUREMENT REPORT (Steps 3 + (n-1)*6):
|
Information element |
Value/remark |
Version |
|
Measurement Information Elements |
||
|
Measurement Identity |
10 |
|
|
Measured Results |
||
|
– CHOICE Measurement |
||
|
– UE positioning measured results |
||
|
– UE positioning OTDOA measured results |
Not present |
|
|
– UE positioning position estimate info |
Not present |
|
|
– UE positioning GPS measured results |
Not present |
|
|
– UE positioning error |
||
|
– Error reason |
Assistance Data Missing |
|
|
– GPS additional assistance data request |
Defines assistance data requested by the UE |
|
|
Measured Results on RACH |
Not present |
|
|
Additional Measured Results |
Not present |
|
|
Event Results |
Not present |
MEASUREMENT CONTROL (Steps 4 + (n-1)*6):
|
Information element |
Value/remark |
Version |
|
Measurement Information Elements |
||
|
Measurement Identity |
10 |
|
|
Measurement Command |
Modify |
|
|
Measurement Reporting Mode |
||
|
– Measurement report transfer mode |
Acknowledged mode RLC |
|
|
– Periodical reporting / Event trigger reporting mode |
Periodical reporting |
|
|
Additional Measurements List |
Not present |
|
|
CHOICE Measurement type |
UE positioning measurement |
|
|
– UE positioning measurement |
||
|
– UE positioning reporting quantity |
||
|
– Method type |
UE assisted |
|
|
– Positioning methods |
GPS |
|
|
– Horizontal accuracy |
19 (51 m) |
|
|
– Vertical accuracy |
48 (102 m) |
|
|
– GPS timing of cell wanted |
FALSE |
|
|
– Additional assistance data request |
FALSE |
|
|
– Environmental characterization |
Not present |
|
|
– GANSSPositioningMethods |
||
|
– Measurement validity |
Bitmap as per supported GNSS |
|
|
– UE state |
All states |
|
|
– CHOICE Reporting criteria |
||
|
– No reporting |
||
|
– UE pos OTDOA assistance data for UE-assisted |
Not present |
|
|
– UE pos OTDOA assistance data for UE-based |
Not present |
|
|
– UE positioning GPS assistance data |
As specified in TS 37.571-5 [48] clause 6.2 and requested by the UE in Step 3+(n-1)*6 |
|
|
Physical Channel Information Elements |
||
|
DPCH compressed mode status info |
Not present |
|
MEASUREMENT CONTROL (Steps 5 + (n-1)*6):
|
Information element |
Value/remark |
Version |
|
Measurement Information Elements |
||
|
Measurement Identity |
10 |
|
|
Measurement Command |
Modify |
|
|
Measurement Reporting Mode |
||
|
– Measurement report transfer mode |
Acknowledged mode RLC |
|
|
– Periodical reporting / Event trigger reporting mode |
Periodical reporting |
|
|
Additional Measurements List |
Not present |
|
|
CHOICE Measurement type |
UE positioning measurement |
|
|
– UE positioning measurement |
||
|
– UE positioning reporting quantity |
||
|
– Method type |
UE assisted |
|
|
– Positioning methods |
GPS |
|
|
– Horizontal accuracy |
19 (51 m) |
|
|
– Vertical accuracy |
48 (102 m) |
|
|
– GPS timing of cell wanted |
FALSE |
|
|
– Additional assistance data request |
FALSE |
|
|
– Environmental characterization |
Not present |
|
|
– GANSSPositioningMethods |
Bitmap as per supported GNSS |
|
|
– Measurement validity |
||
|
– UE state |
All states |
|
|
– CHOICE Reporting criteria |
Periodical Reporting Criteria |
|
|
– Amount of reporting |
1 |
|
|
– Reporting Interval |
20000 |
|
|
– UE pos OTDOA assistance data for UE-assisted |
Not present |
|
|
– UE pos OTDOA assistance data for UE-based |
Not present |
|
|
– UE positioning GANSS assistance data |
||
|
-GanssGenericDataList |
||
|
– GANSS Time model list |
||
|
– UE positioning GANSS reference position info |
As specified in TS 37.571-5 [48] clause 6.2 |
|
|
– UE positioning GANSS AuxiliaryInfo |
As specified in TS 37.571-5 [48] clause 6.2 |
|
|
Physical Channel Information Elements |
||
|
DPCH compressed mode status info |
Not present |
7.5.9 UE assisted A-GNSS procedure for moving scenario and periodic update test case
The procedure in this clause shall be used for the UE-assisted A-GNSS moving scenario and periodic update test case in CELL_DCH and CELL_FACH state as specified in TS 37.571-1 [47] clause 6.
7.5.9.1 Initial conditions
User Equipment:
The UE is in CELL_DCH or CELL_FACH state after executing the procedure defined in clause F.2 of TS 37.571-1 [47].
7.5.9.2 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
RESET UE POSITIONING STORED INFORMATION |
TC |
|
|
2 |
|
RRC MEASUREMENT CONTROL |
RRC (Setup, Periodical Reporting criteria, GPS Ref time, GPS UTC Model, GANSS Time Model) |
|
|
3 |
|
RRC MEASUREMENT CONTROL |
RRC (Additional Assistance Data Request) |
|
|
4 |
|
RRC MEASUREMENT CONTROL |
RRC (Modify, No Reporting, Assistance Data GPS Satellites 1, 2, 3, 4, 5, 6, 7, 8, 9) |
|
|
5 |
|
RRC MEASUREMENT CONTROL |
RRC (Setup, Periodical Reporting criteria, Reference Measurement Info GANSS Satellites 1, 2, 3, 4, 5, 6, 7, 8 Aux Info GANSS Satellites 1, 2, 3, 4, 5, 6, 7, 8) |
|
|
6 |
|
RRC MEASUREMENT REPORT |
RRC (GNSS Measured Results), 1st test Instance |
|
|
7 |
|
RRC MEASUREMENT REPORT |
RRC (GNSS Measured Results), 2nd test Instance |
|
|
… |
|
… |
||
|
n |
|
RRC MEASUREMENT REPORT |
RRC (GNSS Measured Results), nth test Instance |
|
|
NOTE: In the actual testing the UE may report error messages at step 6 until it has been able to acquire GPS measured results. |
||||
7.5.9.3 Specific message contents
Contents of RESET UE POSITIONING STORED INFORMATION message: TC
The contents of the Reset UE Positioning Stored Information message in Step 1 are the same as specified for Normal UE assisted A-GNSS testing in clause 7.5.8.
Contents of MEASUREMENT CONTROL message: RRC
The contents of the Measurement Control message in steps 2 and 4 are the same as specified for Normal UE assisted A-GNSS testing in clause 7.5.8.
The contents of the Measurement Control message in step 5 are the same as specified for Normal UE assisted A-GNSS testing in clause 7.5.8 with the following exceptions:
|
Information Element |
Value/remark |
|
Amount of reporting |
Infinite (see note) |
|
Reporting interval |
2 000 ms |
|
NOTE: Infinite means during the complete test time. |
|