7.4 Common generic procedures for AS testing
34.1083GPPCommon test environments for User Equipment (UE)Conformance testingRelease 15TS
7.4.1 UE RRC Test States for common procedures
Figure 7.4.1.1: UE RRC test initial states and common procedures
For UE to set up a call in UTRAN there are a number of procedures to be undertaken in a hierarchical sequence to move between known states. The sequences are shown in figure 7.4.1.1; the operating states for various protocols in the UE are given in table 7.4.1.1.
It is noted that figure 7.4.1.1 should not be construed as a formal state transition diagram, in any manner. The intention here is to define the starting state of UE following the execution of the procedures indicated above.
Table 7.4.1.1: The UE states
|
RRC |
CC |
MM |
SM |
GMM |
||
|---|---|---|---|---|---|---|
|
State 1 |
Power OFF |
—– |
Null |
Null |
Pdp-Inactive |
GMM-null |
|
State 2 |
Registered Idle Mode on CS |
Idle |
Null |
MM Idle |
Pdp-Inactive |
GMM-deregistered |
|
State 3 |
Registered Idle Mode on PS |
Idle |
Null |
Null |
Pdp-Inactive |
GMM-registered |
|
State 7 |
Registered Idle Mode on CS/PS |
Idle |
Null |
MM Idle |
Pdp-Inactive |
GMM-registered |
|
State BGP6-1 |
CS-CELL_DCH_Initial |
Connected |
Null |
MM Idle |
Pdp-Inactive |
As previous |
|
State BGP6-2 |
CS-CELL_FACH_Initial |
Connected |
Null |
MM Idle |
Pdp-Inactive |
As previous |
|
State BGP6-3 |
PS-CELL_DCH_Initial |
Connected |
Null |
As previous |
Pdp-Inactive |
GMM registered |
|
State BGP6-4 |
PS-CELL_FACH_Initial |
Connected |
Null |
As previous |
Pdp-Inactive |
GMM registered |
|
State BGP6-5 |
CS-DCCH_DCH |
Connected (CELL_DCH) |
Null |
MM Idle |
Pdp-Inactive |
As previous |
|
State BGP6-6 |
CS-DCCH_FACH |
Connected (CELL_FACH) |
Null |
MM Idle |
Pdp-Inactive |
As previous |
|
State BGP6-7 (NOTE1) |
PS-DCCH_DCH |
Connected (CELL_DCH) |
Null |
As previous |
Pdp-Active pending |
GMM registered |
|
State BGP6-8 |
PS-DCCH_FACH |
Connected (CELL_FACH) |
Null |
As previous |
Pdp-Active pending |
GMM registered |
|
State BGP6-9 |
CS-DCCH+DTCH_DCH |
Connected (CELL_DCH) |
Active |
MM connection active |
Pdp-Inactive |
As previous |
|
State BGP6-9a |
CS- DCCH+DTCH_DCH_TEST_LOOP |
Connected (CELL_DCH) |
Null |
MM Idle |
Pdp-Inactive |
As previous |
|
State BGP6-10 |
PS-DCCH+DTCH_DCH |
Connected (CELL_DCH) |
Null |
As previous |
Pdp-Active |
GMM registered |
|
State BGP6-10a |
PS-DCCH+DTCH_DCH_TEST_LOOP |
Connected (CELL_DCH) |
Null |
As previous |
Pdp-Inactive |
GMM registered |
|
State BGP6-11 |
PS-DCCH+DTCH_FACH |
Connected (CELL_FACH) |
Null |
As previous |
Pdp-Active |
GMM registered |
|
State BGP6-11a |
PS-DCCH+DTCH_FACH_TEST_LOOP |
Connected (CELL_FACH) |
Null |
As previous |
Pdp-Inactive |
GMM registered |
|
State BGP6-12 |
CELL_PCH |
Connected (CELL_PCH) |
Null |
As previous |
Pdp-Inactive |
GMM registered |
|
State BGP6-13 |
URA_PCH |
Connected (URA_PCH) |
Null |
As previous |
Pdp-Inactive |
GMM registered |
|
State BGP6-14 |
PS+CS-DCCH+DTCH_DCH |
Connected (CELL_DCH) |
Active |
MM connection active |
Pdp-Active |
GMM registered |
|
State BGP6-15 |
CS+CS-DCCH+DTCH_DCH |
Connected (CELL_DCH) |
Active |
MM connection active |
Pdp-Inactive |
As previous |
|
State BGP6-16 |
PS+PS-DCCH+DTCH_DCH |
Connected (CELL_DCH) |
Null |
As previous |
Pdp-Active |
GMM registered |
|
State BGP6-17 |
PS-DCCH+DTCH_HS-DSCH |
Connected (CELL_DCH) |
Null |
As previous |
Pdp-Active |
GMM registered |
|
State BGP6-18 |
PS-DCCH+DTCH_E-DCH/HS-DSCH |
Connected (CELL_DCH) |
Null |
As previous |
Pdp-Active |
GMM registered |
|
State BGP6-19 |
PS+PS-DCCH+DTCH_Idle |
Idle |
Null |
MM Idle |
Pdp-Active |
GMM registered |
|
NOTE1: The default procedure to move from state BGP6-1 to state BGP6-7 is the procedure P9. |
||||||
State 1, state 2, state 3, P1, P2 and P1a are described in clause 7.2.
7.4.2 Generic Setup Procedure for RRC test cases
7.4.2.1 RRC connection establishment procedure for circuit-switched calls (procedure P3 and P4)
7.4.2.1.1 Mobile terminating call
7.4.2.1.1.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be operated under normal test conditions as specified in the present document.
– The Test USIM shall be inserted.
7.4.2.1.1.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.1.1.3 Procedure
The Call Set-up procedure shall be performed under ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
PAGING TYPE 1 (PCCH) |
RRC |
|
|
2 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
3 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
5 |
|
PAGING RESPONSE |
RR |
|
7.4.2.1.1.4 Specific message contents
To execute procedure P3, all specific message contents shall be referred to clause 9.
To execute procedure P4, all specific message contents with the exception of step 3 shall be referred to clause 9. For step 3, the message of the same type titled "Transition to CELL_FACH" in clause 9 is used.
7.4.2.1.2 Mobile originating calls
7.4.2.1.2.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be operated under normal test conditions as specified in the present document.
– The Test USIM shall be inserted.
7.4.2.1.2.2 Definition of system information messages
The default system information messages specified in clause 6.1 are used.
7.4.2.1.2.3 Procedure
The Call Set-up procedure shall be performed under ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
2 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
3 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
4 |
|
CM SERVICE REQUEST |
MM |
|
7.4.2.1.2.4 Specific message contents
To execute procedure P3, all specific message contents shall be referred to clause 9.
To execute procedure P4, all specific message contents with the exception of step 2 shall be referred to clause 9. For step 2, the message of the same type titled "Transition to CELL_FACH" in clause 9 is used.
7.4.2.2 RRC connection establishment procedure for packet switched sessions (procedure P5 and P6)
7.4.2.2.1 Mobile terminating session
7.4.2.2.1.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be operated under normal test conditions as specified in the present document.
– The Test USIM shall be inserted.
7.4.2.2.1.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.2.1.3 Procedure
The Session Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
PAGING TYPE1 (PCCH) |
Paging |
|
|
2 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
3 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
5 |
|
SERVICE REQUEST |
GMM |
|
7.4.2.2.1.4 Specific message contents
To execute procedure P5, all specific message contents shall be referred to clause 9.
To execute procedure P6, all specific message contents with the exception of step 3 shall be referred to clause 9. For step 3, the message of the same type titled "Transition to CELL_FACH" in clause 9 is used.
7.4.2.2.2 Mobile originating sessions
7.4.2.2.2.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be operated under normal test conditions as specified in the present document.
– The Test USIM shall be inserted.
7.4.2.2.2.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.2.2.3 Procedure
The Session Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
2 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
3 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
4 |
|
SERVICE REQUEST |
GMM |
|
7.4.2.2.2.4 Specific message contents
To execute procedure P5, all specific message contents shall be referred to clause 9.
To execute procedure P6, all specific message contents with the exception of step 2 shall be referred to clause 9. For step 2, the message of the same type titled "Transition to CELL_FACH" in clause 9 is used.
7.4.2.3 NAS call set up procedure for circuit switched calls (procedure P7 and P8)
7.4.2.3.1 Mobile terminating call
7.4.2.3.1.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-1 or state 6-2.
– The Test USIM shall be inserted.
7.4.2.3.1.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.3.1.3 Procedure
The Call Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
AUTHENTICATION REQUEST |
MM |
|
|
2 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
3 |
|
SECURITY MODE COMMAND |
RRC |
|
|
4 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
5 |
|
SET UP |
CC |
|
|
6 |
|
CALL CONFIRMED |
CC |
|
7.4.2.3.1.4 Specific message contents
All RRC specific message contents shall be referred to clause 9.
7.4.2.3.2 Mobile originating calls
7.4.2.3.2.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-1or state 6-2.
– The Test USIM shall be inserted.
7.4.2.3.2.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.3.2.3 Procedure
The Call Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
AUTHENTICATION REQUEST |
MM |
|
|
2 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
3 |
|
SECURITY MODE COMMAND |
RRC |
|
|
4 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
5 |
|
SET UP |
CC |
|
|
6 |
|
CALL PROCEEDING |
CC |
|
7.4.2.3.2.4 Specific message contents
All RRC specific message contents shall be referred to clause 9.
7.4.2.4 NAS session activation procedure for packet switched sessions (procedure P9 and P10)
7.4.2.4.1 Mobile terminating session
7.4.2.4.1.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-3 or state 6-4.
– The Test USIM shall be inserted.
7.4.2.4.1.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.4.1.3 Procedure
The Session Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
2 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
3 |
|
SECURITY MODE COMMAND |
RRC |
|
|
4 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
5 |
|
REQUEST PDP CONTEXT ACTIVATION |
SM |
|
|
6 |
|
ACTIVATE PDP CONTEXT REQUEST |
SM |
|
7.4.2.4.1.4 Specific message contents
All RRC specific message contents shall be referred to clause 9.
7.4.2.4.2 Mobile originating sessions
7.4.2.4.2.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-3 or state 6-4.
– The Test USIM shall be inserted.
7.4.2.4.2.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.4.2.3 Procedure
The Session Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
2 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
3 |
|
SECURITY MODE COMMAND |
RRC |
|
|
4 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
5 |
|
ACTIVATE PDP CONTEXT REQUEST |
SM |
|
7.4.2.4.2.4 Specific message contents
All RRC specific message contents shall be referred to clause 9.
7.4.2.4a NAS session activation procedure for packet switched sessions with active set update (procedure P9b)
7.4.2.4a.1 Mobile terminating session
7.4.2.4a.1.1 Initial conditions
System Simulator:
– 1 serving cell default parameters. 1 neighbour cell.
User Equipment:
– The UE shall be in state 6-3.
– The Test USIM shall be inserted.
7.4.2.4a.1.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.4a.1.3 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
2 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
3 |
|
SECURITY MODE COMMAND |
RRC |
|
|
4 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
5 |
|
REQUEST PDP CONTEXT ACTIVATION |
SM |
|
|
6 |
|
ACTIVATE PDP CONTEXT REQUEST |
SM |
|
|
7 |
Set the power level of the neighbour cell to -60dBm. Any MEASUREMENT REPORT received is ignored. |
|||
|
8 |
|
ACTIVE SET UPDATE |
RRC |
|
|
9 |
|
ACTIVE SET UPDATE COMPLETE |
RRC |
|
7.4.2.4a.1.4 Specific message contents
All RRC specific message contents shall be referred to clause 9 with the following exceptions.
ACTIVE SET UPDATE (Step 8)
|
Information Element |
Value/remark |
Version |
|
Radio link addition information |
||
|
– Primary CPICH Info |
||
|
– Primary Scrambling Code |
Set to the Primary Scrambling Code of neighbour cell. Refer to clause 6.1. |
|
|
– Downlink DPCH info for each RL |
||
|
– CHOICE mode |
FDD |
|
|
– Primary CPICH usage for channel estimation |
P-CPICH can be used. |
|
|
– DPCH frame offset |
Calculated value from cells timing information |
|
|
– Secondary CPICH info |
Not Present |
|
|
– DL channelisation code |
||
|
– Secondary scrambling code |
1 |
|
|
– Spreading factor |
According to clause 6.10.2.4.1.3 (standalone 13.6 kbps signalling radio bearer) |
|
|
– Code Number |
0 |
|
|
– Scrambling code change |
Not Present |
|
|
– TPC Combination Index |
0 |
|
|
– SSDT Cell Identity |
Not Present |
R99 and Rel-4 only |
|
– Close loop timing adjustment mode |
Not Present |
|
|
– TFCI Combining Indicator |
FALSE |
|
|
– SCCPCH information for FACH |
Not Present |
R99 and Rel-4 only |
7.4.2.4a.2 Mobile originating sessions
7.4.2.4a.2.1 Initial conditions
System Simulator:
– 1 serving cell default parameters. 1 neighbour cell.
User Equipment:
– The UE shall be in 6-3.
– The Test USIM shall be inserted.
7.4.2.4a.2.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.4a.2.3 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
2 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
3 |
|
SECURITY MODE COMMAND |
RRC |
|
|
4 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
5 |
|
ACTIVATE PDP CONTEXT REQUEST |
SM |
|
|
6 |
Set the power level of the neighbour cell to -60dBm. Any MEASUREMENT REPORT received is ignored. |
|||
|
7 |
|
ACTIVE SET UPDATE |
RRC |
|
|
8 |
|
ACTIVE SET UPDATE COMPLETE |
RRC |
|
7.4.2.4a.2.4 Specific message contents
All RRC specific message contents shall be referred to clause 9 with the following exceptions.
ACTIVE SET UPDATE (Step 7) same as ACTIVE SET UPDATE (Step 8) in clause 7.4.2.4a.1.4.
7.4.2.5 Radio access bearer establishment procedure for circuit switched calls (procedure P11 and P12)
7.4.2.5.1 Mobile terminating call
7.4.2.5.1.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-5 or state 6-6.
– The Test USIM shall be inserted.
7.4.2.5.1.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.5.1.3 Procedure
The Call Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
RADIO BEARER SETUP |
RRC RAB SETUP |
|
|
2 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
3 |
|
ALERTING |
CC (This message is optional) |
|
|
4 |
|
CONNECT |
CC |
|
|
5 |
|
CONNECT ACKNOWLEDGE |
CC |
|
7.4.2.5.1.4 Specific message contents
To execute procedure P11, use the message titled "CS speech" (defined in clause 9) for the message in step 1. To execute procedure 12, use the message "The others of speech in CS" (defined in clause 9) for the message in step 1.
7.4.2.5.2 Mobile originating calls
7.4.2.5.2.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-5 or state 6-6.
– The Test USIM shall be inserted.
7.4.2.5.2.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.5.2.3 Procedure
The Call Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
RADIO BEARER SETUP |
RRC RAB SETUP |
|
|
2 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
3 |
|
ALERTING |
CC |
|
|
4 |
|
CONNECT |
CC |
|
|
5 |
|
CONNECT ACKOWLEDGE |
CC |
|
7.4.2.5.2.4 Specific message contents
To execute procedure P11, use the message titled "CS speech" (defined in clause 9) for the message in step 1. To execute procedure 12, use the message "The others of speech in CS" (defined in clause 9) for the message in step 1.
7.4.2.5a Test loop activation and radio access bearer establishment procedure for circuit switched calls (procedure P7a)
7.4.2.5a.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-1.
– The Test USIM shall be inserted.
7.4.2.5a.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.5a.3 Procedure
The Call Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
AUTHENTICATION REQUEST |
MM |
|
|
2 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
3 |
|
SECURITY MODE COMMAND |
RRC |
|
|
4 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
5 |
|
ACTIVATE RB TEST MODE (DCCH) |
TC |
|
|
6 |
|
ACTIVATE RB TEST MODE COMPLETE (DCCH) |
TC |
|
|
1 |
|
RADIO BEARER SETUP |
RRC RAB SETUP |
|
|
2 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
14 |
|
CLOSE UE TEST LOOP (DCCH) |
TC UE test mode 1 RLC SDU size set as specified for the actual test case. |
|
|
15 |
|
CLOSE UE TEST LOOP COMPLETE (DCCH) |
TC |
|
7.4.2.5a.4 Specific message contents
To execute procedure P7a, use the message titled "CS speech" (defined in clause 9) for the message in step 1.
7.4.2.6 Radio access bearer establishment procedure for packet switched sessions (procedure P13, P14, P25 and P26)
7.4.2.6.1 Mobile terminating session
7.4.2.6.1.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-7 or state 6-8.
– The Test USIM shall be inserted.
7.4.2.6.1.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.6.1.3 Procedure
The Session Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
RADIO BEARER SETUP |
RRC RAB SETUP |
|
|
2 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
3 |
|
ACTIVATE PDP CONTEXT ACCEPT |
SM |
|
7.4.2.6.1.4 Specific message contents
For step 1, the messages in clause 9 are used. To execute procedure P13, use the message titled "Packet to CELL_DCH from CELL_DCH in PS". To execute procedure P14, use the message titled "Packet to CELL_FACH from CELL_FACH in PS". To execute procedure P25, use the message titled "Packet to CELL_DCH / HS-DSCH from CELL_DCH in PS". To execute procedure P26, use the RADIO BEARER SETUP message with one of the conditions A12, A13, A14, A15, A16, A19, A20, A21 or A22.
Contents of ACTIVATE PDP CONTEXT ACCEPT message: DCCH-AM (Step 3)
|
Information Element |
Value/remark |
|
|
WLAN offload indication |
WLAN |
‘0010’B |
|
Condition |
Explanation |
|
WLAN |
For RAN Assisted WLAN interworking test cases |
7.4.2.6.2 Mobile originating sessions
7.4.2.6.2.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-7 or state 6-8.
– The Test USIM shall be inserted.
7.4.2.6.2.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.6.2.3 Procedure
The Session Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
RADIO BEARER SETUP |
RRC RAB SETUP |
|
|
2 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
3 |
|
ACTIVATE PDP CONTEXT ACCEPT |
SM |
|
7.4.2.6.2.4 Specific message contents
For step 1, the messages in clause 9 are used. To execute procedure P13, use the message titled "Packet to CELL_DCH from CELL_DCH in PS". To execute procedure P14, use the message titled "Packet to CELL_FACH from CELL_FACH in PS". To execute procedure P25, use the message titled "Packet to CELL_DCH / HS-DSCH from CELL_DCH in PS". To execute procedure P26, use the RADIO BEARER SETUP message with one of the conditions A12, A13, A14, A15 or A16.
Contents of ACTIVATE PDP CONTEXT ACCEPT message: DCCH-AM (Step 3)
|
Information Element |
Value/remark |
|
|
WLAN offload indication |
WLAN |
‘0010’B |
|
Condition |
Explanation |
|
WLAN |
For RAN Assisted WLAN interworking test cases |
7.4.2.6a Test loop activation and radio access bearer establishment procedure for packet switched sessions (procedure P4a and P9a)
7.4.2.6a.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-3 or state 6-4.
– The Test USIM shall be inserted.
7.4.2.6a.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.6a.3 Procedure
The Session Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
2 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
3 |
|
SECURITY MODE COMMAND |
RRC |
|
|
4 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
5 |
|
ACTIVATE RB TEST MODE (DCCH) |
TC |
|
|
6 |
|
ACTIVATE RB TEST MODE COMPLETE (DCCH) |
TC |
|
|
7 |
|
RADIO BEARER SETUP |
RRC RAB SETUP. The ‘pdcp info’ IE shall be omitted. |
|
|
8 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
14 |
|
CLOSE UE TEST LOOP (DCCH) |
TC UE test mode 1 RLC SDU size set as specified for the actual test case. |
|
|
15 |
|
CLOSE UE TEST LOOP COMPLETE (DCCH) |
TC |
|
7.4.2.6a.4 Specific message contents
For step 1, the messages in clause 9 are used. To execute procedure P9a, use the message titled "Packet to CELL_DCH from CELL_DCH in PS". To execute procedure 4a, use the message titled "Packet to CELL_FACH from CELL_FACH in PS" with the exception that the ‘pdcp info’ IE shall be omitted.
7.4.2.7 Procedure for transitions to CELL_PCH or URA_PCH state (procedure P15, P16, P17 and P18)
7.4.2.7.1 Transition to CELL_PCH (procedure P15 and P16)
7.4.2.7.1.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-10 or state 6-11.
– The Test USIM shall be inserted.
7.4.2.7.1.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.7.1.3 Procedure
The Call Set-up procedure shall be performed under ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
PHYSICAL CHANNEL RECONFIGURATION |
RRC |
|
|
2 |
|
PHYSICAL CHANNEL RECONFIGURATION COMPLETE |
RRC |
|
7.4.2.7.1.4 Specific message contents
Contents of PHYSICAL CHANNEL RECONFIGURATION message: DCCH-AM (Step 1)
|
Information Element |
Value/remark |
|
Message Type |
|
|
RRC State Indicator |
CELL_PCH |
7.4.2.7.2 Transition to URA_PCH (procedure P17 and P18)
7.4.2.7.2.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-10 or state 6-11.
– The Test USIM shall be inserted.
7.4.2.7.2.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.7.2.3 Procedure
The Call Set-up procedure shall be performed under ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
PHYSICAL CHANNEL RECONFIGURATION |
RRC |
|
|
2 |
|
PHYSICAL CHANNEL RECONFIGURATION COMPLETE |
RRC |
|
7.4.2.7.2.4 Specific message contents
Contents of PHYSICAL CHANNEL RECONFIGURATION message: DCCH-AM (Step 1)
|
Information Element |
Value/remark |
|
Message Type |
|
|
RRC State Indicator |
URA_PCH |
7.4.2.8 Radio access bearer establishment procedure with packet switched sessions for transitions to Multi Call state (procedure P19, 20 and 21)
7.4.2.8.1 Transition to PS+CS-DCCH+DTCH DCH (procedure P19)
7.4.2.8.1.1 Mobile terminating session
7.4.2.8.1.1.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall have registered in CS/PS.
– The UE shall be in state 6-9.
– The Test USIM shall be inserted.
7.4.2.8.1.1.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.8.1.1.3 Procedure
The Session Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|---|---|---|---|---|
|
UE |
SS |
|||
|
1 |
|
PAGING TYPE2 (DCCH) |
Paging |
|
|
2 |
|
SERVICE REQUEST |
GMM |
|
|
3 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
4 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
5 |
|
SECURITY MODE COMMAND |
RRC |
|
|
6 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
7 |
|
REQUEST PDP CONTEXT ACTIVATION |
SM |
|
|
8 |
|
ACTIVATE PDP CONTEXT REQUEST |
SM |
|
|
9 |
|
RADIO BEARER SETUP |
RRC RAB SETUP |
|
|
10 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
11 |
|
ACTIVATE PDP CONTEXT ACCEPT |
SM |
|
7.4.2.8.1.1.4 Specific message contents
FFS
7.4.2.8.1.2 Mobile originating sessions
7.4.2.8.1.2.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-9.
– The Test USIM shall be inserted.
7.4.2.8.1.2.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.8.1.2.3 Procedure
The Session Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SERVICE REQUEST |
GMM |
|
|
2 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
3 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
4 |
|
SECURITY MODE COMMAND |
RRC |
|
|
5 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
6 |
|
ACTIVATE PDP CONTEXT REQUEST |
SM |
|
|
7 |
|
RADIO BEARER SETUP |
RRC RAB SETUP |
|
|
8 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
9 |
|
ACTIVATE PDP CONTEXT ACCEPT |
SM |
|
7.4.2.8.1.2.4 Specific message contents
FFS
7.4.2.8.2 Transition to PS+PS-DCCH+DTCH DCH (procedure P20 and P21)
7.4.2.8.2.1 Mobile terminating session
7.4.2.8.2.1.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-10 or state 6-11.
– The Test USIM shall be inserted.
7.4.2.8.2.1.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.8.2.1.3 Procedure
The Session Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
PAGING TYPE2 (DCCH) |
Paging |
|
|
2 |
|
SERVICE REQUEST |
GMM |
|
|
3 |
|
SERVICE ACCEPT |
GMM |
|
|
4 |
|
REQUEST PDP CONTEXT ACTIVATION |
SM |
|
|
5 |
|
ACTIVATE PDP CONTEXT REQUEST |
SM |
|
|
6 |
|
RADIO BEARER SETUP |
RRC RAB SETUP |
|
|
7 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
8 |
|
ACTIVATE PDP CONTEXT ACCEPT |
SM |
|
7.4.2.8.2.1.4 Specific message contents
FFS
7.4.2.8.2.2 Mobile originating sessions
7.4.2.8.2.2.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-10 or state 6-11.
– The Test USIM shall be inserted.
7.4.2.8.2.2.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.8.2.2.3 Procedure
The Session Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SERVICE REQUEST |
GMM |
|
|
2 |
|
SERVICE ACCEPT |
GMM |
|
|
3 |
|
ACTIVATE PDP CONTEXT REQUEST |
SM |
|
|
4 |
|
RADIO BEARER SETUP |
RRC RAB SETUP |
|
|
5 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
6 |
|
ACTIVATE PDP CONTEXT ACCEPT |
SM |
|
7.4.2.8.2.2.4 Specific message contents
FFS
7.4.2.8.3 Transition to PS+PS-DCCH+DTCH Idle (Procedure P27)
7.4.2.8.3.1 Mobile terminating session
7.4.2.8.3.1.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-16.
– The Test USIM shall be inserted.
7.4.2.8.3.1.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.8.3.1.3 Procedure
The Session Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
RRC CONNECTION RELEASE (DCCH) |
N308=1 |
|
|
2 |
|
RRC CONNECTION RELEASE COMPLETE (DCCH) |
The UE shall enter idle state. Message is repeated 2(N308+1) times |
|
7.4.2.8.3.1.4 Specific message contents
None
7.4.2.9 Radio access bearer establishment procedure with circuit switched calls for transitions to Multi Call state (procedure P22, P23 and P24)
7.4.2.9.1 Transition to CS+CS-DCCH+DTCH DCH (procedure P22)
7.4.2.9.1.1 Mobile terminating call
7.4.2.9.1.1.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-9.
– The Test USIM shall be inserted.
7.4.2.9.1.1.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.9.1.1.3 Procedure
The Call Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
PAGING TYPE2 (DCCH) |
Paging |
|
|
2 |
|
PAGING RESPONSE |
RR |
|
|
3 |
|
SET UP |
CC |
|
|
4 |
|
CALL CONFIRMED |
CC |
|
|
5 |
|
RADIO BEARER SETUP |
RRC RAB SETUP |
|
|
6 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
7 |
|
ALERTING |
CC (this message is optional) |
|
|
8 |
|
CONNECT |
CC |
|
|
9 |
|
CONNECT ACKNOWLEDGE |
CC |
|
7.4.2.9.1.1.4 Specific message contents
FFS
7.4.2.9.1.2 Mobile originating calls
7.4.2.9.1.2.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-9.
– The Test USIM shall be inserted.
7.4.2.9.1.2.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.9.1.2.3 Procedure
The Call Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
CM SERVICE REQUEST |
MM |
|
|
2 |
|
CM SERVICE ACCEPT |
MM |
|
|
3 |
|
SET UP |
CC |
|
|
4 |
|
CALL PROCEEDING |
CC |
|
|
5 |
|
RADIO BEARER SETUP |
RRC RAB SETUP |
|
|
6 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
7 |
|
ALERTING |
CC |
|
|
8 |
|
CONNECT |
CC |
|
|
9 |
|
CONNECT ACKNOWLEDGE |
CC |
|
7.4.2.9.1.2.4 Specific message contents
FFS
7.4.2.9.2 Transition to PS+CS-DCCH+DTCH DCH (procedure P23 and 24)
7.4.2.9.2.1 Mobile terminating call
7.4.2.9.2.1.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall have registered in CS/PS.
– The UE shall be in state 6-10 or state 6-11.
– The Test USIM shall be inserted.
7.4.2.9.2.1.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.9.2.1.3 Procedure
The Call Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|---|---|---|---|---|
|
UE |
SS |
|||
|
1 |
|
PAGING TYPE2 (DCCH) |
Paging |
|
|
2 |
|
PAGING RESPONSE |
RR |
|
|
3 |
|
AUTHENTICATION REQUEST |
MM |
|
|
4 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
5 |
|
SECURITY MODE COMMAND |
RRC |
|
|
6 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
7 |
|
SET UP |
CC |
|
|
8 |
|
CALL CONFIRMED |
CC |
|
|
9 |
|
RADIO BEARER SETUP |
RRC RAB SETUP |
|
|
10 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
11 |
|
ALERTING |
CC (this message is optional) |
|
|
12 |
|
CONNECT |
CC |
|
|
13 |
|
CONNECT ACKNOWLEDGE |
CC |
|
7.4.2.9.2.1.4 Specific message contents
FFS
7.4.2.9.2.2 Mobile originating calls
7.4.2.9.2.2.1 Initial conditions
System Simulator:
– 1 cell, default parameters.
User Equipment:
– The UE shall be in state 6-10 or state 6-11.
– The Test USIM shall be inserted.
7.4.2.9.2.2.2 Definition of system information messages
The default system information messages are used as specified in clause 6.1.
7.4.2.9.2.2.3 Procedure
The Call Set-up procedure shall be performed under Ideal radio conditions as defined in clauses 5.2 and 6.1.
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
CM SERVICE REQUEST |
MM |
|
|
2 |
|
AUTHENTICATION REQUEST |
MM |
|
|
3 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
4 |
|
SECURITY MODE COMMAND |
RRC |
|
|
5 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
6 |
|
SET UP |
CC |
|
|
7 |
|
CALL PROCEEDING |
CC |
|
|
8 |
|
RADIO BEARER SETUP |
RRC RAB SETUP |
|
|
9 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
10 |
|
ALERTING |
CC |
|
|
11 |
|
CONNECT |
CC |
|
|
12 |
|
CONNECT ACKOWLEDGE |
CC |
|
7.4.2.9.2.2.4 Specific message contents
FFS