7.3 Test procedures for RF test
34.1083GPPCommon test environments for User Equipment (UE)Conformance testingRelease 15TS
NOTE: In general parameters defined for specific test cases in 3GPP TS 34.121 [2] take priority over the default parameters defined in the present document.
7.3.1 UE Test States for RF testing
In this clause, the states of the UE for the test are defined. For RF testing the same UE test states as specified in section 7.2.1 apply plus an additional RB Test Mode State. The RB Test Mode State can be reached from the UE States 2, 3 and 7 according to section 7.2.1. For this RB Test Mode State the different protocols shall be in the following states:
|
RRC |
CC |
MM |
SM |
GMM |
|
|
RB Test Mode State |
connected |
null |
see Note |
pdp-inactive |
same as previous state |
|
NOTE: The MM state is "MM connection active" if an RRC connection exists for the CS domain otherwise it is "same as previous state". |
|||||
7.3.2 Test procedure for TX, RX and Performance Requirement (without handover)
7.3.2.1 Initial conditions
System Simulator
– test cases using 1 cell:
– 1cell, default parameters.
– other test cases using this test procedure:
– Number of cells and parameters for specific tests are defined in 3GPP TS 34.121 [2] and take priority over the default parameters.
User Equipment:
– The UE shall initially be operated under normal RF test conditions if not otherwise stated in the initial conditions for the actual test case.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.2.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
7.3.2.3 Procedure
7.3.2.3.1 For UE supporting CS
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (CS domain, TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
PAGING RESPONSE |
RR |
|
|
7 |
|
AUTHENTICATION REQUEST |
MM |
|
|
8 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
12 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
13 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP) |
|
|
14 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
15 |
|
CLOSE UE TEST LOOP (DCCH) |
TC (UE test loop mode set up) |
|
|
16 |
|
CLOSE UE TEST LOOP COMPLETE |
TC (confirms that loopback entities for the radio bearer(s) have been created and loop back is activated) |
|
|
17 |
|
OPEN UE TEST LOOP |
TC |
|
|
18 |
|
OPEN UE TEST LOOP COMPLETE |
TC |
|
|
19 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
20 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.2.3.2 For UE supporting PS only
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (PS domain, P-TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
SERVICE REQUEST |
GMM |
|
|
7 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
8 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
12 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
13 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP) |
|
|
14 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
15 |
|
CLOSE UE TEST LOOP (DCCH) |
TC (UE test loop mode set up) |
|
|
16 |
|
CLOSE UE TEST LOOP COMPLETE |
TC (confirms that loopback entities for the radio bearer(s) have been created and loop back is activated) |
|
|
17 |
|
OPEN UE TEST LOOP |
TC |
|
|
18 |
|
OPEN UE TEST LOOP COMPLETE |
TC |
|
|
19 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
20 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.2.3.3 For CS+PS multi RAB combination
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (CS domain, TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
PAGING RESPONSE |
RR |
|
|
7 |
|
AUTHENTICATION REQUEST |
MM |
|
|
8 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 12 13 14 15 |
|
PAGING TYPE 2 (DCCH) SERVICE REQUEST SECURITY MODE COMMAND SECURITY MODE COMPLETE ACTIVATE RB TEST MODE |
TMSI (GSM-MAP)/ P-TMSI GMM RRC RRC TC |
|
|
16 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
17 |
|
RADIO BEARER SETUP |
RRC CS radio bearer(s) are configured |
|
|
18 19 20 |
|
RADIO BEARER SETUP COMPLETE RADIO BEARER SETUP RADIO BEARER SETUP COMPLETE |
RRC RRC PS radio bearer(s) are configured RRC |
|
|
21 |
|
CLOSE UE TEST LOOP (DCCH) |
TC (UE test loop mode set up) |
|
|
22 |
|
CLOSE UE TEST LOOP COMPLETE |
TC (confirms that loopback entities for the radio bearer(s) have been created and loop back is activated) |
|
|
23 |
|
OPEN UE TEST LOOP |
TC |
|
|
24 |
|
OPEN UE TEST LOOP COMPLETE |
TC |
|
|
25 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
26 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.2.4 Specific message contents
The default message contents specified in clause 9.2 are used with the following exceptions.
7.3.2.4.1 ATTACH ACCEPT
This message is sent from the SS to the UE, used for the UE supporting PS only.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
7.3.2.4.2 Reference measurement channels
The configurations of the reference measurement channels for RF tests are described in 3GPP TS 34.121 [2], annex C for FDD and 3GPP TS 34.122 [5], annex C for TDD.
7.3.2.4.3 Void
7.3.2.4.4 Compressed mode
[T.B.D]
7.3.2.4.5 Transmit diversity mode
[T.B.D]
7.3.3 Test procedure for test cases using Cell_PCH or URA_PCH state
7.3.3.1 Initial conditions
System Simulator:
– Number of cells and parameters for specific tests are defined in 3GPP TS 34.121 [2] and take priority over the default parameters.
User Equipment:
– The UE shall be operated under RF test conditions.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.3.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|---|---|
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
7.3.3.3 Procedure
7.3.3.3.1 For UE supporting PS
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (PS domain, P-TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
SERVICE REQUEST |
GMM |
|
|
7 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
8 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
12 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
13 |
|
RADIO BEARER SETUP |
RRC – RAB SETUP using Reference Radio Bearer Configuration |
|
|
14 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
15 |
|
PHYSICAL CHANNEL RECONFIGURATION |
RRC – RRC state indicator is set to "Cell_PCH" or "URA_PCH" depending on the test case |
|
|
16 |
|
PHYSICAL CHANNEL RECONFIGURATION COMPLETE |
RRC The UE sends this message before it completes state transition. |
|
|
17 |
Void |
SS sends the L2 ack on the PHYSICAL CHANNEL RECONFIGURATION COMPLETE message. NOTE: The SS should continue to keep the dedicated channel configuration during the time when the L2 ack is sent to the UE. |
||
7.3.3.4 Specific message contents
The default message contents specified in clause 9.2 are used with the following exceptions.
The RADIO BEARER SETUP message is defined in clause 9.2.1, "Contents of RADIO BEARER SETUP message: AM or UM (UE supports PS RAB only)".
The PHYSICAL CHANNEL RECONFIGURATION message is defined in clause 9.1.1, "Contents of PHYSICAL CHANNEL RECONFIGURATION message: AM or UM" using condition A8 for URA_PCH and condition A10 for Cell_PCH.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
7.3.4 Test procedure for Handover
NOTE: This test procedure is also used for some other test cases involving more than 1 cell.
7.3.4.1 Initial conditions
System Simulator:
– Intra-frequency hard handover and soft handover (for FDD) case:
– 2 cells, default parameters according to Cell 1 and Cell 2 in clause 6.1.4.
– Inter-frequency hard handover case:
– 2 cells, default parameters according to Cell 1 and Cell 4 in clause 6.1.4.
– Inter-system handover UTRAN to GSM case:
– 2 cells, default parameters according to Cell 1 and Cell 9 in clause 6.1.4.
– other test cases using this test procedure:
– Number of cells and parameters for specific tests are defined in 3GPP TS 34.121 [2] for FDD and TS 34.122 [5] for TDD and take priority over the default parameters.
UserEquipment:
– The UE shall be initially operated under the normal RF test conditions if not otherwise stated in the initial conditions for the actual test case.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.4.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|---|---|
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
For the intra-frequency hard handover and soft handover (for FDD) case the default messages for SIB11 and SIB12 as specified for Cell 1 and Cell 2 in clause 6.1.4 are used.
For the inter-frequency hard handover case the default messages for SIB11 and SIB12 as specified for Cell 1 and Cell 4 in clause 6.1.4 are used.
For the inter-system handover from UTRAN to GSM case the default messages for SIB11 and SIB12 as specified for Cell 1 and Cell 9 in clause 6.1.4 are used.
7.3.4.3 Procedure
7.3.4.3.1 For UE supporting CS
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (CS domain, TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
PAGING RESPONSE |
RR |
|
|
7 |
|
AUTHENTICATION REQUEST |
MM |
|
|
8 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
12 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
13 |
|
RADIO BEARER SETUP |
RRC – RAB SETUP using Reference Radio Bearer Configuration – RRC state indicator is set to "CELL_DCH" |
|
|
14 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
15 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
16 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.4.3.2 For UE supporting PS only
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (PS domain, P-TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
SERVICE REQUEST |
GMM |
|
|
7 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
8 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
12 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
13 |
|
RADIO BEARER SETUP |
RRC – RAB SETUP using Reference Radio Bearer Configuration – RRC state indicator is set to "CELL_DCH" |
|
|
14 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
15 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
16 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.4.4 Specific message contents
The default message contents specified in clause 9.2 are used with the following exceptions.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
7.3.5 Test procedure for test cases using CELL_FACH state
7.3.5.1 Initial conditions
System Simulator:
– Number of cells and parameters for specific tests are defined in TS 34.121 [2] and take priority over the default parameters.
User Equipment:
– The UE shall be operated under RF test conditions.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.5.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
7.3.5.3 Procedure
7.3.5.3.1 For UE supporting CS
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (CS domain, TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
PAGING RESPONSE |
RR |
|
|
7 |
|
AUTHENTICATION REQUEST |
MM |
|
|
8 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
12 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
13 |
|
DEACTIVATE RB TEST MODE |
TC |
|
|
14 |
|
DEACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
15 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
16 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.5.3.2 For UE supporting PS only
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (PS domain, P-TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
SERVICE REQUEST |
GMM |
|
|
7 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
8 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
12 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
13 |
|
DEACTIVATE RB TEST MODE |
TC |
|
|
14 |
|
DEACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
15 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
16 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.5.4 Specific message contents
The default message contents specified in clause 9.2 are used with the following exceptions.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
The RRC connection setup is defined in clause 9.1.1, "Contents of RRC CONNECTION SETUP message: UM (Transition to CELL_FACH)".
7.3.6 Test procedure for HSDPA RF Performance Requirement
7.3.6.1 Initial conditions
System Simulator:
– 1 HS-DSCH cell, default parameters.
User Equipment:
– The UE shall initially be operated under normal RF test conditions if not otherwise stated in the initial conditions for the actual test case.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.6.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|---|---|
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
7.3.6.3 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (CS domain, TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
PAGING RESPONSE |
RR |
|
|
7 |
|
AUTHENTICATION REQUEST |
MM |
|
|
8 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC (CS domain) |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
PAGING TYPE2 (DCCH) |
Paging (TMSI (GSM-MAP)/ P-TMSI) |
|
|
12 |
|
SERVICE REQUEST |
GMM |
|
|
13 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
14 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
15 |
|
SECURITY MODE COMMAND |
RRC (PS domain, IE Integrity protection mode command set to "modify") |
|
|
16 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
17 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
18 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
19 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP RMC 12.2 CS) |
|
|
20 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
21 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP HSDPA PS) |
|
|
22 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
A23 |
|
CLOSE UE TEST LOOP (DCCH) |
TC (UE test loop mode set up to loop the RMC 12.2 to UL RMC 12.2) . Test steps A23, A24, A26 and A27 are only executed when the test method in TS 34.121 [2] specifies that loopback test shall be used. |
|
|
A24 |
|
CLOSE UE TEST LOOP COMPLETE |
TC (confirms that loopback entities for the radio bearer(s) have been created and loop back is activated) |
|
|
25 |
<–> |
Perform test |
||
|
A26 |
|
OPEN UE TEST LOOP |
TC |
|
|
A27 |
|
OPEN UE TEST LOOP COMPLETE |
TC |
|
|
28 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
29 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.6.4 Specific message contents
The default message contents specified in clause 9.2 are used with the following exceptions.
7.3.6.4.1 ATTACH ACCEPT
This message is sent from the SS to the UE.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
7.3.6.4.2 RADIO BEARER SETUP
For step 19, the message in clause 9.2, "Contents of RADIO BEARER SETUP message: AM or UM (Test Loop Mode1)" is used with condition A1. For step 21, the message in clause 9.2, "Contents of RADIO BEARER SETUP message: AM or UM (HSDPA)" is used.
The configurations of the fixed reference channels for HSDPA RF tests are described in 3GPP TS 34.121[2], annex C for FDD and 3GPP TS 34.122 [5], annex C for TDD.
7.3.6.4.3 RRC CONNECTION SETUP
For step 4 , the message in clause 9.2, "Contents of RRC CONNECTION SETUP message: UM" is used with the following exceptions:
Contents of RRC CONNECTION SETUP message: UM
|
Information Element |
Value/remark |
|
– Default DPCH Offset Value |
Arbitrary set to value 1536..306176 by step of 2560 (this corresponds to a 0.5 slot timing offset between the DPCCH and the HS-DPCCH) |
7.3.7 Test procedure for inter-RAT handover used in RRM testing
7.3.7.1 Initial conditions
System Simulator:
– 2 cells, default parameters according to Cell 1 and Cell 9 in clause 6.1.4.
UserEquipment:
– The UE shall be initially operated under the normal RF test conditions if not otherwise stated in the initial conditions for the actual test case.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.7.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|---|---|
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
For the inter-system handover from UTRAN FDD to GSM case the default messages for SIB11 and SIB12 as specified for Cell 1 and Cell 9 in clause 6.1.4 are used.
7.3.7.3 Procedure
|
Step |
Direction |
Message |
Comments |
|
|---|---|---|---|---|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING (PCCH) |
Paging |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC (Transition to cell DCH) |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
PAGING RESPONSE |
RR |
|
|
7 |
|
AUTHENTICATION REQUEST |
MM |
|
|
8 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
SET UP |
CC (see note) |
|
|
12 |
|
CALL CONFIRMED |
CC |
|
|
13 |
|
RADIO BEARER SETUP |
RRC RAB SETUP |
|
|
14 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
15 |
|
ALERTING |
CC (this message is optional) |
|
|
16 |
|
CONNECT |
CC |
|
|
17 |
|
CONNECT ACKNOWLEDGE |
CC |
|
|
NOTE: The "Signal" information element is not included in the SETUP message. |
||||
7.3.7.4 Specific message contents
The default message contents specified in clause 9.1 are used with the following exceptions.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
7.3.8 Test procedure for inter-RAT cell FACH reselection used in RRM testing
7.3.8.1 Initial conditions
System Simulator:
– Number of cells and parameters for specific tests are defined in TS 34.121 [2] and take priority over the default parameters.
User Equipment:
– The UE shall be operated under RF test conditions.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.8.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
7.3.8.3 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
3 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
5 |
|
SERVICE REQUEST |
GMM |
|
|
6 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
7 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
8 |
|
SECURITY MODE COMMAND |
RRC |
|
|
9 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
10 |
|
ACTIVATE PDP CONTEXT REQUEST |
SM |
|
|
11 |
|
RADIO BEARER SETUP |
RRC RAB SETUP |
|
|
12 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
13 |
|
ACTIVATE PDP CONTEXT ACCEPT |
SM |
|
7.3.8.4 Specific message contents
The default message contents specified in clause 9.1 are used with the following exceptions.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
The RRC connection setup is defined in clause 9.1.1, "Contents of RRC CONNECTION SETUP message: UM (Transition to CELL_FACH)".
7.3.9 Test procedure for E-DCH RF test cases
7.3.9.1 Initial conditions
System Simulator:
– 1 HS-DSCH plus E-DCH cell, default parameters.
User Equipment:
– The UE shall initially be operated under normal RF test conditions if not otherwise stated in the initial conditions for the actual test case.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.9.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|---|---|
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
7.3.9.3 Procedure
7.3.9.3.1 For UE transmitting on E-DCH with DCH
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (CS domain, TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
PAGING RESPONSE |
RR |
|
|
7 |
|
AUTHENTICATION REQUEST |
MM |
|
|
8 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC (CS domain) |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
PAGING TYPE2 (DCCH) |
Paging (TMSI (GSM-MAP)/ P-TMSI) |
|
|
12 |
|
SERVICE REQUEST |
GMM |
|
|
13 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
14 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
15 |
|
SECURITY MODE COMMAND |
RRC (PS domain, IE Integrity protection mode command set to "modify") |
|
|
16 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
17 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
18 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
19 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP RMC 12.2 CS) |
|
|
20 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
21 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP HSDPA and E-DCH PS) |
|
|
22 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
A23 |
|
CLOSE UE TEST LOOP (DCCH) |
TC (UE test loop mode set up) . Test steps A23, A24, A26 and A27 are only executed when the test method in TS 34.121 [2] specifies that loopback test shall be used. |
|
|
A24 |
|
CLOSE UE TEST LOOP COMPLETE |
TC (confirms that loopback entities for the radio bearer(s) have been created and loop back is activated) |
|
|
25 |
<–> |
Perform test |
||
|
A26 |
|
OPEN UE TEST LOOP |
TC |
|
|
A27 |
|
OPEN UE TEST LOOP COMPLETE |
TC |
|
|
28 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
29 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.9.3.2 For UE transmitting on E-DCH without DCH
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (PS domain, P-TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
SERVICE REQUEST |
GMM |
|
|
7 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
8 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC (PS domain) |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
12 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
13 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP HSDPA and E-DCH PS) |
|
|
14 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
A15 |
|
CLOSE UE TEST LOOP (DCCH) |
TC (UE test loop mode set up) . Test steps A15, A16, A18 and A19 are only executed when the test method in TS 34.121 [2] specifies that loopback test shall be used. |
|
|
A16 |
|
CLOSE UE TEST LOOP COMPLETE |
TC (confirms that loopback entities for the radio bearer(s) have been created and loop back is activated) |
|
|
17 |
<–> |
Perform test |
||
|
A18 |
|
OPEN UE TEST LOOP |
TC |
|
|
A19 |
|
OPEN UE TEST LOOP COMPLETE |
TC |
|
|
20 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
21 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.9.4 Specific message contents
The default message contents specified in clause 9.2 are used with the following exceptions.
7.3.9.4.1 ATTACH ACCEPT
This message is sent from the SS to the UE.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
7.3.9.4.2 RADIO BEARER SETUP
For step 19, the message in clause 9.2, "Contents of RADIO BEARER SETUP message: AM or UM (Test Loop Mode1)" is used with condition A1. For step 21, the message in clause 9.2, "Contents of RADIO BEARER SETUP message: AM or UM (E-DCH and HSDPA)" is used.
The configurations of the fixed reference channels for HSDPA RF tests are described in 3GPP TS 34.121[2], annex C for FDD and 3GPP TS 34.122 [5], annex C for TDD. The configurations of the reference channels for E-DCH RF tests are described in 3GPP TS 34.121[2].
7.3.9.4.3 RRC CONNECTION SETUP
For step 4 , the messages in clause 9.2, "Contents of RRC CONNECTION SETUP message: UM" is used with the following exceptions:
Contents of RRC CONNECTION SETUP message: UM
|
Information Element |
Value/remark |
|
– Default DPCH Offset Value |
Arbitrary set to value 1536..306176 by step of 2560 (this corresponds to a 0.5 slot timing offset between the DPCCH and the HS-DPCCH) |
7.3.10 Test procedure for MBMS RF/RRM test cases
7.3.10.1 Initial conditions
System Simulator:
– Number of cells and parameters for specific tests are defined in TS 34.121 [2] and take priority over the default parameters.
User Equipment:
– The UE shall be operated under RF test conditions.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.10.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|---|---|
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
As specified in 34.108 clause 6.1.0b with the following exceptions and using condition M2.
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
7.3.10.3 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
0 |
UE selects the required MBMS broadcast service |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
MBMS MODIFIED SERVICES INFORMATION (MCCH) |
No Service in Modified Service list |
|
|
3 |
|
MBMS UNMODIFIED SERVICES INFORMATION (MCCH) |
MBMS required UE action " set to acquire PTM RB info”. |
|
|
4 |
|
MBMS GENERAL INFORMATION (MCCH) |
||
|
5 |
|
MBMS COMMON P-T-M RB INFORMATION (MCCH) |
Contains configuration of the MTCH radio bearer. |
|
|
6 |
|
MBMS CURRENT CELL P-T-M RB INFORMATION (MCCH) |
Indicates the radio bearer configuration to be used for reception of the service. |
|
|
7 |
|
MBMS NEIGHBOURING CELL P-T-M RB INFORMATION (MCCH) |
Optional depending on whether neighbour cells are required. |
|
|
8 |
|
PAGING TYPE1 (PCCH) |
Paging (PS domain, P-TMSI) |
|
|
9 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
10 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
11 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
12 |
|
SERVICE REQUEST |
GMM |
|
|
13 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
14 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
15 |
|
SECURITY MODE COMMAND |
RRC |
|
|
16 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
17 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
18 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
19 |
void |
|||
|
20 |
|
CLOSE UE TEST LOOP |
TC (UE test loop mode 3 set up) The RLC SDU counting shall be performed by the UE |
|
|
21 |
|
CLOSE UE TEST LOOP COMPLETE |
TC (test loop mode 3 on MTCH is activated) |
|
|
A22 |
|
PHYSICAL CHANNEL RECONFIGURATION |
RRC – RRC state indicator set to "Cell_PCH" Test steps A22 and A23 are only executed when the test method in TS 34.121 [2] specifies that transition to CELL_PCH state is required. |
|
|
A23 |
|
PHYSICAL CHANNEL RECONFIGURATION COMPLETE |
RRC The UE sends this message before it completes state transition. |
|
|
<–> |
Perform test. |
|||
|
A24 |
|
PAGING TYPE 1 |
RRC – RRC state indicator set to "Cell_FACH" Test steps A24, A25 and A26 are only executed when the test method in TS 34.121 [2] specifies that the test is performed in CELL_PCH state. |
|
|
A25 |
|
CELL UPDATE |
RRC |
|
|
A26 |
|
CELL UPDATE CONFIRM |
RRC |
|
|
27 |
|
OPEN UE TEST LOOP |
TC |
|
|
28 |
|
OPEN UE TEST LOOP COMPLETE |
TC |
|
|
29 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
30 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.10.4 Specific message contents
The default message contents specified in clause 9.1.1 are used with the following exceptions.
Contents of MBMS GENERAL INFORMATION message: UM (Step 4)
|
Information Element |
Value/remark |
Version |
|---|---|---|
|
MICH configuration information |
Rel-6 |
|
|
– MICH Power offset |
0dB |
Rel-6 |
|
– CHOICE Mode |
FDD |
Rel-6 |
|
– Channelisation code |
7 |
Rel-6 |
|
– Number of NI per frame |
18 |
Rel-6 |
|
– STTD indicator |
FALSE |
Rel-6 |
Contents of MBMS COMMON P-T-M RB INFORMATION message: UM (Step 5)
For step 5, the message in clause 9.2.1 “Contents of MBMS COMMON P-T-M RB INFORMATION message: UM” is used
Contents of MBMS CURRENT P-T-M RB INFORMATION message: UM (Step 6)
For step 6, the message in clause 9.1.1 “Contents of MBMS CURRENT P-T-M RB INFORMATION message: UM” is used with condition A2.
PHYSICAL CHANNEL RECONFIGURATION (Step A22)
For step A22, the message in clause 9.1.1 "Contents of PHYSICAL CHANNEL RECONFIGURATION message: AM or UM" is used with condition A9 for Cell_PCH.
PAGING TYPE 1 (Step A24)
|
Information Element |
Value/remark |
|
Message Type |
|
|
Paging record list |
|
|
-Paging record |
|
|
– CHOICE Used paging identity |
Utran-Identity |
|
-U-RNTI |
|
|
-SRNC-Identity |
‘000000000001’B |
|
-S-RNTI |
‘00000000000000000001’B |
|
BCCH modification info |
Not Present |
Contents of ATTACH ACCEPT message: GMM
This message is sent from the SS to the UE.
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
7.3.11 Test procedure for HSDPA with F-DPCH RF Performance Requirement
7.3.11.1 Initial conditions
System Simulator:
– 1 HS-DSCH with F-DPCH cell, default parameters.
User Equipment:
– The UE shall initially be operated under normal RF test conditions if not otherwise stated in the initial conditions for the actual test case.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.11.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|---|---|
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
7.3.11.3 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (PS domain, P-TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
SERVICE REQUEST |
GMM |
|
|
7 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
8 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC (PS domain) |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
12 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
13 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP HSDPA with F-DPCH) |
|
|
14 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
15 |
<–> |
Perform test |
||
|
16 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
17 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.11.4 Specific message contents
The default message contents specified in clause 9.2 are used with the following exceptions.
7.3.11.4.1 ATTACH ACCEPT
This message is sent from the SS to the UE.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
7.3.11.4.2 RADIO BEARER SETUP
For step 13, the message in clause 9.2, "Contents of RADIO BEARER SETUP message: AM or UM (HSDPA with F-DPCH)" is used.
The configurations of the fixed reference channels for HSDPA RF tests are described in 3GPP TS 34.121[2], annex C for FDD and 3GPP TS 34.122 [5], annex C for TDD.
7.3.11.4.3 RRC CONNECTION SETUP
For step 4 , the message in clause 9.2, "Contents of RRC CONNECTION SETUP message: UM" is used with the following exceptions:
Contents of RRC CONNECTION SETUP message: UM
|
Information Element |
Value/remark |
|
– Default DPCH Offset Value |
Arbitrary set to value 1536..306176 by step of 2560 (this corresponds to a 0.5 slot timing offset between the DPCCH and the HS-DPCCH) |
7.3.12 Test procedure for HSDPA in CELL_FACH RF Performance Requirement
7.3.12.1 Initial conditions
System Simulator:
– Number of cells and parameters for specific tests are defined in TS 34.121 [2] and take priority over the default parameters.
User Equipment:
– The UE shall be operated under RF test conditions.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.12.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
Additional crucial parameters for the test requirements are repeated in table 7.3.12-1 and these overrule the parameters defined in SIB type 5.
Table 7.3.12.1: UE parameters for Random Access test
|
Parameter |
Unit |
Value |
|
Maximum number of preamble ramping cycles (Mmax). |
2 |
|
|
Maximum number of preambles in one preamble ramping cycle |
2 |
|
|
The backoff time TB01 |
ms |
N/A |
|
Power step when no acquisition indicator is received |
dB |
3 |
|
Power offset between the last transmitted preamble and the control part of the message (Power offset P p-m) |
dB |
0 |
|
Maximum allowed UL TX power |
dBm |
21 |
7.3.12.3 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (PS domain, P-TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
SERVICE REQUEST |
GMM |
|
|
7 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
8 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
12 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
13 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP HSDPA PS in CELL_FACH) |
|
|
14 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
15 |
|
CLOSE UE TEST LOOP |
TC (UE test loop mode 1 set up) The RLC SDU counting shall be performed by the SS |
|
|
16 |
|
CLOSE UE TEST LOOP COMPLETE |
TC (test loop mode 1 on DTCH is activated) |
|
|
17 |
<–> |
Perform test. |
||
|
18 |
|
OPEN UE TEST LOOP |
TC |
|
|
19 |
|
OPEN UE TEST LOOP COMPLETE |
TC |
|
|
20 |
DEACTIVATE RB TEST MODE |
TC |
||
|
21 |
DEACTIVATE RB TEST MODE COMPLETE |
TC |
||
|
22 |
|
RRC CONNECTION RELEASE |
RRC |
|
7.3.12.4 Specific message contents
The default message contents specified in clause 9.2 are used with the following exceptions.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
The RRC connection setup is defined in clause 9.1.1, "Contents of RRC CONNECTION SETUP message: UM (Transition to CELL_FACH)".
For step 13, the message in clause 9.1.1, " Contents of RADIO BEARER SETUP message: AM or UM" is used with condition A24. Default parameters are set for “Interactive/Background / UL:32 DL: [max bit rate depending on UE category] with fixed RLC and MAC-ehs / PS RAB + SRBs for CCCH + DCCH on RACH and SRB with fixed RLC and MAC-ehs on HS-DSCH / DL:QPSK” in clause 6.10.2.4.7.1 using the 10 ms UL TTI alternative with the following exception:
|
Information Element |
Condition |
Value/remark |
Version |
|---|---|---|---|
|
– Number of uplink RLC logical channels |
|
1 |
|
|
– Uplink transport channel type |
|
RACH |
|
|
– UL Transport channel identity |
|
Not Present |
|
|
– Logical channel identity |
|
7 |
|
|
– CHOICE RLC size list |
|
Explicit list |
|
|
– RLC size index |
|
Reference to clause 6 Parameter Set |
|
|
– MAC logical channel priority |
|
1 (Note 1) |
– |
Note 1: The exception is required to get ASC #0 according to 25.321 section 11.2.1. ASC#0 guarantee persistance value 1 to not cause delay in the RACH procedure.
The configurations of the fixed reference channels for HSDPA RF tests are described in 3GPP TS 34.121[2], annex C for FDD and 3GPP TS 34.122 [5], annex C for TDD.
7.3.13 Test procedure for DC-HSDPA and DB-DC-HSDPA RF tests
7.3.13.1 Initial conditions
System Simulator:
– Dual HS-DSCH cell, default parameters.
User Equipment:
– The UE shall initially be operated under normal RF test conditions if not otherwise stated in the initial conditions for the actual test case.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.13.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|---|---|
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
7.3.13.3 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (CS domain, TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
PAGING RESPONSE |
RR |
|
|
7 |
|
AUTHENTICATION REQUEST |
MM |
|
|
8 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC (CS domain) |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
PAGING TYPE2 (DCCH) |
Paging (TMSI (GSM-MAP)/ P-TMSI) |
|
|
12 |
|
SERVICE REQUEST |
GMM |
|
|
13 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
14 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
15 |
|
SECURITY MODE COMMAND |
RRC (PS domain, IE Integrity protection mode command set to "modify") |
|
|
16 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
17 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
18 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
19 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP RMC 12.2 CS) |
|
|
20 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
21 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP DC-HSDPA PS) |
|
|
22 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
23 |
<–> |
Perform test |
||
|
24 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
25 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.13.4 Specific message contents
The default message contents specified in clause 9.2 are used with the following exceptions.
7.3.13.4.1 ATTACH ACCEPT
This message is sent from the SS to the UE.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
7.3.13.4.2 RADIO BEARER SETUP
For step 19, the message in clause 9.2, "Contents of RADIO BEARER SETUP message: AM or UM (Test Loop Mode1)" is used with condition A1. For step 21, the message in clause 9.2, " RADIO BEARER SETUP message: AM or UM (DC-HSDPA)" is used.
The configurations of the fixed reference channels for HSDPA RF tests are described in 3GPP TS 34.121[2], annex C for FDD and 3GPP TS 34.122 [5], annex C for TDD.
7.3.13.4.3 RRC CONNECTION SETUP
For step 4 , the message in clause 9.2, "Contents of RRC CONNECTION SETUP message: UM" is used with the following exceptions:
Contents of RRC CONNECTION SETUP message: UM
|
Information Element |
Value/remark |
|
– Default DPCH Offset Value |
Arbitrary set to value 1536..306176 by step of 2560 (this corresponds to a 0.5 slot timing offset between the DPCCH and the HS-DPCCH) |
7.3.14 Test procedure for DC-HSUPA RF tests
7.3.14.1 Initial conditions
System Simulator:
– Dual E-DCH cell, default parameters.
User Equipment:
– The UE shall initially be operated under normal RF test conditions if not otherwise stated in the initial conditions for the actual test case.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.14.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|---|---|
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
7.3.14.3 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (CS domain, TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
PAGING RESPONSE |
RR |
|
|
7 |
|
AUTHENTICATION REQUEST |
MM |
|
|
8 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC (CS domain) |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
PAGING TYPE2 (DCCH) |
Paging (TMSI (GSM-MAP)/ P-TMSI) |
|
|
12 |
|
SERVICE REQUEST |
GMM |
|
|
13 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
14 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
15 |
|
SECURITY MODE COMMAND |
RRC (PS domain, IE Integrity protection mode command set to "modify") |
|
|
16 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
17 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
18 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
21 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP DC-HSUPA PS) |
|
|
22 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
23 |
<–> |
Perform test |
||
|
24 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
25 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.14.4 Specific message contents
The default message contents specified in clause 9.2 are used with the following exceptions.
7.3.14.4.1 ATTACH ACCEPT
This message is sent from the SS to the UE.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
7.3.14.4.2 RADIO BEARER SETUP
The Radio Bearer Setup message is defined in clause 9.2, “Contents of RADIO BEARER SETUP message: AM or UM (DC-HSUPA)”.
The configurations of the fixed reference channels for HSDPA RF tests are described in 3GPP TS 34.121[2], annex C for FDD and 3GPP TS 34.122 [5], annex C for TDD.
7.3.14.4.3 RRC CONNECTION SETUP
The RRC connection setup is defined in clause 9.1.1, "Contents of RRC CONNECTION SETUP message: UM (Transition to CELL_FACH)".
7.3.15 Test procedure for Multiple-cell Performance Requirement for 1,28 Mcps TDD
7.3.15.1 Initial conditions
System Simulator
– Number of cells and parameters for specific tests are defined in TS 34.122 [5] and take priority over the default parameters.
User Equipment:
– The UE shall be operated under RF test conditions.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.15.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 11 (1.28 Mcps TDD)
This is the default message content of SIB 11 for cell 1.
|
– Intra-frequency measurement identity |
Not Present Absence of this IE is equivalent to default value 1 |
|
|
– Intra-frequency cell info list |
||
|
– CHOICE intra-frequency cell removal |
Not present (This IE shall be ignored by the UE for SIB11) |
|
|
– New intra-frequency cells |
||
|
– Intra-frequency cell id |
1 |
|
|
– Cell info |
||
|
– Cell individual offset |
Not present Absence of this IE is equivalent to default value 0dB |
|
|
– Reference time difference to cell |
Not Present |
|
|
– Read SFN Indicator |
FALSE |
|
|
– CHOICE mode |
TDD |
|
|
– Primary CCPCH info |
||
|
– Cell parameters ID |
19 |
|
|
– Primary CCPCH TX power |
Not Present |
|
|
– Timeslot list |
Not Present |
|
|
– CHOICE TDD option |
||
|
– 1.28 Mcps TDD |
||
|
– Timeslot number |
Not Present |
|
|
– Cell Selection and Re-selection info |
Not Present (The IE shall be absent as this is the serving cell) |
|
|
– Intra-frequency cell id |
2 |
|
|
– Cell info |
||
|
– Cell individual offset |
Not present Absence of this IE is equivalent to default value 0dB |
|
|
– Reference time difference to cell |
Not Present |
|
|
– Read SFN Indicator |
FALSE |
|
|
– CHOICE mode |
TDD |
|
|
– Primary CCPCH info |
||
|
– Cell parameters ID |
58 |
|
|
– Primary CCPCH TX power |
Not Present |
|
|
– Timeslot list |
Not Present |
|
|
– CHOICE TDD option |
||
|
– 1.28 Mcps TDD |
||
|
– Timeslot number |
Not Present |
|
|
– Cell Selection and Re-selection info |
Not Present |
|
|
– Intra-frequency cell id |
3 |
|
|
– Cell info |
||
|
– Cell individual offset |
Not present Absence of this IE is equivalent to default value 0dB |
|
|
– Reference time difference to cell |
Not Present |
|
|
– Read SFN Indicator |
FALSE |
|
|
– CHOICE mode |
TDD |
|
|
– Primary CCPCH info |
||
|
– Cell parameters ID |
85 |
|
|
– Primary CCPCH TX power |
Not Present |
|
|
– Timeslot list |
Not Present |
|
|
– CHOICE TDD option |
||
|
– 1.28 Mcps TDD |
||
|
– Timeslot number |
Not Present |
|
|
– Cell Selection and Re-selection info |
Not Present |
|
|
– Intra-frequency cell id |
7 |
|
|
– Cell info |
Same content as specified for intra-frequency cell id=2 with the exception that value for Cell Parameters ID shall be according to clause titled “Default settings for cell No.7(TDD)” in clause 6.1.4 |
|
|
– Intra-frequency cell id |
8 |
|
|
– Cell info |
Same content as specified for intra-frequency cell id=2 with the exception that value for Cell Parameters ID shall be according to clause titled “Default settings for cell No.8(TDD)” in clause 6.1.4 |
7.3.15.3 Procedure
7.3.15.3.1 For UE supporting CS
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (CS domain, TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
PAGING RESPONSE |
RR |
|
|
7 |
|
AUTHENTICATION REQUEST |
MM |
|
|
8 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
12 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
13 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP) |
|
|
14 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
15 |
|
CLOSE UE TEST LOOP (DCCH) |
TC (UE test loop mode set up) |
|
|
16 |
|
CLOSE UE TEST LOOP COMPLETE |
TC (confirms that loopback entities for the radio bearer(s) have been created and loop back is activated) |
|
|
17 |
|
OPEN UE TEST LOOP |
TC |
|
|
18 |
|
OPEN UE TEST LOOP COMPLETE |
TC |
|
|
19 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
20 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.15.3.2 For UE supporting PS only
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (PS domain, P-TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
SERVICE REQUEST |
GMM |
|
|
7 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
8 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
12 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
13 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP) |
|
|
14 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
15 |
|
CLOSE UE TEST LOOP (DCCH) |
TC (UE test loop mode set up) |
|
|
16 |
|
CLOSE UE TEST LOOP COMPLETE |
TC (confirms that loopback entities for the radio bearer(s) have been created and loop back is activated) |
|
|
17 |
|
OPEN UE TEST LOOP |
TC |
|
|
18 |
|
OPEN UE TEST LOOP COMPLETE |
TC |
|
|
19 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
20 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.15.4 Specific message contents
The default message contents specified in clause 9.2 are used with the following exceptions.
7.3.15.4.1 ATTACH ACCEPT
This message is sent from the SS to the UE, used for the UE supporting PS only.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
7.3.15.4.2 Reference measurement channels
The configurations of the reference measurement channels for RF tests are described in 3GPP TS 34.122 [5], annex C for TDD.
7.3.16 Test procedure for 4C-HSDPA RF tests
7.3.16.1 Initial conditions
System Simulator:
– Dual HS-DSCH cell, default parameters.
User Equipment:
– The UE shall initially be operated under normal RF test conditions if not otherwise stated in the initial conditions for the actual test case.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.16.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|---|---|
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
7.3.16.3 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (CS domain, TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
PAGING RESPONSE |
RR |
|
|
7 |
|
AUTHENTICATION REQUEST |
MM |
|
|
8 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC (CS domain) |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
PAGING TYPE2 (DCCH) |
Paging (TMSI (GSM-MAP)/ P-TMSI) |
|
|
12 |
|
SERVICE REQUEST |
GMM |
|
|
13 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
14 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
15 |
|
SECURITY MODE COMMAND |
RRC (PS domain, IE Integrity protection mode command set to "modify") |
|
|
16 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
17 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
18 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
19 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP RMC 12.2 CS) |
|
|
20 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
21 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP DC-HSDPA PS) |
|
|
22 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
23 |
<–> |
Perform test |
||
|
24 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
25 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.16.4 Specific message contents
The default message contents specified in clause 9.2 are used with the following exceptions.
7.3.16.4.1 ATTACH ACCEPT
This message is sent from the SS to the UE.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
7.3.16.4.2 RADIO BEARER SETUP
For step 19, the message in clause 9.2, "Contents of RADIO BEARER SETUP message: AM or UM (Test Loop Mode1)" is used with condition A1. For step 21, the message in clause 9.2, " RADIO BEARER SETUP message: AM or UM (DC-HSDPA)" is used with secondary serving cell defined as per table 5.0aB or 5.0aC of 3GPP TS 25.101.
The configurations of the fixed reference channels for HSDPA RF tests are described in 3GPP TS 34.121[2], annex C for FDD and 3GPP TS 34.122 [5], annex C for TDD.
7.3.16.4.3 RRC CONNECTION SETUP
For step 4 , the message in clause 9.2, "Contents of RRC CONNECTION SETUP message: UM" is used with the following exceptions:
Contents of RRC CONNECTION SETUP message: UM
|
Information Element |
Value/remark |
|
– Default DPCH Offset Value |
Arbitrary set to value 1536..306176 by step of 2560 (this corresponds to a 0.5 slot timing offset between the DPCCH and the HS-DPCCH) |
7.3.17 Test procedure for TX, RX and Performance Requirement for UL CLTD
7.3.17.1 Initial conditions
System Simulator:
– 1 HS-DSCH cell, default parameters.
User Equipment:
– The UE shall initially be operated under normal RF test conditions if not otherwise stated in the initial conditions for the actual test case.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.17.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|---|---|
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
7.3.17.3 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (CS domain, TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
PAGING RESPONSE |
RR |
|
|
7 |
|
AUTHENTICATION REQUEST |
MM |
|
|
8 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC (CS domain) |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
PAGING TYPE2 (DCCH) |
Paging (TMSI (GSM-MAP)/ P-TMSI) |
|
|
12 |
|
SERVICE REQUEST |
GMM |
|
|
13 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
14 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
15 |
|
SECURITY MODE COMMAND |
RRC (PS domain, IE Integrity protection mode command set to "modify") |
|
|
16 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
17 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
18 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
19 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP RMC 12.2 CS) |
|
|
20 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
21 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP HSDPA PS) |
|
|
22 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
A23 |
|
CLOSE UE TEST LOOP (DCCH) |
TC (UE test loop mode set up to loop the RMC 12.2 to UL RMC 12.2). Test steps A23, A24, A26 and A27 are only executed when the test method in TS 34.121 [2] specifies that loopback test shall be used. |
|
|
A24 |
|
CLOSE UE TEST LOOP COMPLETE |
TC (confirms that loopback entities for the radio bearer(s) have been created and loop back is activated) |
|
|
25 |
<–> |
Perform test |
||
|
A26 |
|
OPEN UE TEST LOOP |
TC |
|
|
A27 |
|
OPEN UE TEST LOOP COMPLETE |
TC |
|
|
28 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
29 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.17.4 Specific message contents
The default message contents specified in clause 9.2 are used with the following exceptions.
7.3.17.4.1 ATTACH ACCEPT
This message is sent from the SS to the UE.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
7.3.17.4.2 RADIO BEARER SETUP
For step 19, the message in clause 9.2, "Contents of RADIO BEARER SETUP message: AM or UM (Test Loop Mode1)" is used with condition A1. For step 21, the message in clause 9.2, "Contents of RADIO BEARER SETUP message: AM or UM (HSDPA)" is used, with follwing exceptions.
|
Information Element |
Value/remark |
Version |
|---|---|---|
|
Uplink CLTD info FDD |
Rel-11 |
|
|
– CHOICE Mode |
New |
|
|
– S-DPCCH Info |
||
|
– S-DPCCH/DPCCH power offset |
0 |
|
|
– Initial CLTD activation state |
First state |
|
|
– Primary CPICH Info |
||
|
– Primary Scrambling Code |
Reference to clause 6.1 "Default settings (FDD)" |
|
Information Element |
Value/remark |
Version |
|---|---|---|
|
F-TPICH Info |
Rel-11 |
|
|
– F-TPICH slot format |
1 |
|
|
– F-TPICH Code number |
6 |
|
|
– F-TPICH frame offset |
1024 |
The configurations of the fixed reference channels for HSDPA RF tests are described in 3GPP TS 34.121[2], annex C for FDD and 3GPP TS 34.122 [5], annex C for TDD.
7.3.17.4.3 RRC CONNECTION SETUP
For step 4, the message in clause 9.2, "Contents of RRC CONNECTION SETUP message: UM" is used with the following exceptions:
Contents of RRC CONNECTION SETUP message: UM
|
Information Element |
Value/remark |
|
– Default DPCH Offset Value |
Arbitrary set to value 1536..306176 by step of 2560 (this corresponds to a 0.5 slot timing offset between the DPCCH and the HS-DPCCH) |
7.3.18 Test procedure for TX, RX and Performance Requirement for UL OLTD
7.3.18.1 Initial conditions
System Simulator:
– 1 HS-DSCH cell, default parameters.
User Equipment:
– The UE shall initially be operated under normal RF test conditions if not otherwise stated in the initial conditions for the actual test case.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.18.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|---|---|
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
7.3.18.3 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (CS domain, TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
PAGING RESPONSE |
RR |
|
|
7 |
|
AUTHENTICATION REQUEST |
MM |
|
|
8 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC (CS domain) |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
PAGING TYPE2 (DCCH) |
Paging (TMSI (GSM-MAP)/ P-TMSI) |
|
|
12 |
|
SERVICE REQUEST |
GMM |
|
|
13 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
14 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
15 |
|
SECURITY MODE COMMAND |
RRC (PS domain, IE Integrity protection mode command set to "modify") |
|
|
16 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
17 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
18 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
19 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP RMC 12.2 CS) |
|
|
20 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
21 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP HSDPA PS) |
|
|
22 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
A23 |
|
CLOSE UE TEST LOOP (DCCH) |
TC (UE test loop mode set up to loop the RMC 12.2 to UL RMC 12.2). Test steps A23, A24, A26 and A27 are only executed when the test method in TS 34.121 [2] specifies that loopback test shall be used. |
|
|
A24 |
|
CLOSE UE TEST LOOP COMPLETE |
TC (confirms that loopback entities for the radio bearer(s) have been created and loop back is activated) |
|
|
25 |
<–> |
Perform test |
||
|
A26 |
|
OPEN UE TEST LOOP |
TC |
|
|
A27 |
|
OPEN UE TEST LOOP COMPLETE |
TC |
|
|
28 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
29 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.18.4 Specific message contents
The default message contents specified in clause 9.2 are used with the following exceptions.
7.3.18.4.1 ATTACH ACCEPT
This message is sent from the SS to the UE.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
7.3.18.4.2 RADIO BEARER SETUP
For step 19, the message in clause 9.2, "Contents of RADIO BEARER SETUP message: AM or UM (Test Loop Mode1)" is used with condition A1. For step 21, the message in clause 9.2, "Contents of RADIO BEARER SETUP message: AM or UM (HSDPA)" is used, with following exceptions
|
Information Element |
Value/remark |
Version |
|---|---|---|
|
Uplink OLTD info FDD |
Rel-11 |
|
|
– Uplink OLTD activation |
TRUE |
|
Information Element |
Value/remark |
Version |
|---|---|---|
|
F-TPICH Info |
Rel-11 |
|
|
– F-TPICH slot format |
1 |
|
|
– F-TPICH Code number |
6 |
|
|
– F-TPICH frame offset |
1024 |
The configurations of the fixed reference channels for HSDPA RF tests are described in 3GPP TS 34.121[2], annex C for FDD and 3GPP TS 34.122 [5], annex C for TDD.
7.3.18.4.3 RRC CONNECTION SETUP
For step 4, the message in clause 9.2, "Contents of RRC CONNECTION SETUP message: UM" is used with the following exceptions:
Contents of RRC CONNECTION SETUP message: UM
|
Information Element |
Value/remark |
|
– Default DPCH Offset Value |
Arbitrary set to value 1536..306176 by step of 2560 (this corresponds to a 0.5 slot timing offset between the DPCCH and the HS-DPCCH) |
7.3.19 Test procedure for TX, RX and Performance Requirement for UL CLTD with HSDPA & E-DCH
7.3.19.1 Initial conditions
System Simulator:
– 1 HS-DSCH plus E-DCH cell, default parameters.
User Equipment:
– The UE shall initially be operated under normal RF test conditions if not otherwise stated in the initial conditions for the actual test case.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.19.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|---|---|
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
7.3.19.3 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (CS domain, TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
PAGING RESPONSE |
RR |
|
|
7 |
|
AUTHENTICATION REQUEST |
MM |
|
|
8 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC (CS domain) |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
PAGING TYPE2 (DCCH) |
Paging (TMSI (GSM-MAP)/ P-TMSI) |
|
|
12 |
|
SERVICE REQUEST |
GMM |
|
|
13 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
14 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
15 |
|
SECURITY MODE COMMAND |
RRC (PS domain, IE Integrity protection mode command set to "modify") |
|
|
16 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
17 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
18 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
19 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP RMC 12.2 CS) |
|
|
20 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
21 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP HSDPA and E-DCH PS) |
|
|
22 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
A23 |
|
CLOSE UE TEST LOOP (DCCH) |
TC (UE test loop mode set up). Test steps A23, A24, A26 and A27 are only executed when the test method in TS 34.121 [2] specifies that loopback test shall be used. |
|
|
A24 |
|
CLOSE UE TEST LOOP COMPLETE |
TC (confirms that loopback entities for the radio bearer(s) have been created and loop back is activated) |
|
|
25 |
<–> |
Perform test |
||
|
A26 |
|
OPEN UE TEST LOOP |
TC |
|
|
A27 |
|
OPEN UE TEST LOOP COMPLETE |
TC |
|
|
28 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
29 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.19.4 Specific message contents
The default message contents specified in clause 9.2 are used with the following exceptions.
7.3.19.4.1 ATTACH ACCEPT
This message is sent from the SS to the UE.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
7.3.19.4.2 RADIO BEARER SETUP
For step 19, the message in clause 9.2, "Contents of RADIO BEARER SETUP message: AM or UM (Test Loop Mode1)" is used with condition A1. For step 21, the message in clause 9.2, "Contents of RADIO BEARER SETUP message: AM or UM (E-DCH and HSDPA)" is used, with following exceptions:
|
Information Element |
Value/remark |
Version |
|---|---|---|
|
Uplink CLTD info FDD |
Rel-11 |
|
|
– CHOICE Mode |
New |
|
|
– S-DPCCH Info |
||
|
– S-DPCCH/DPCCH power offset |
0 |
|
|
– Initial CLTD activation state |
First state |
|
|
– Primary CPICH Info |
||
|
– Primary Scrambling Code |
Reference to clause 6.1 "Default settings (FDD)" |
|
Information Element |
Value/remark |
Version |
|---|---|---|
|
F-TPICH Info |
Rel-11 |
|
|
– F-TPICH slot format |
1 |
|
|
– F-TPICH Code number |
6 |
|
|
– F-TPICH frame offset |
1024 |
The configurations of the fixed reference channels for HSPA RF tests are described in 3GPP TS 34.121[2], annex C for FDD and 3GPP TS 34.122 [5], annex C for TDD.. The configurations of the reference channels for E-DCH RF tests are described in 3GPP TS 34.121[2].
7.3.19.4.3 RRC CONNECTION SETUP
For step 4, the message in clause 9.2, "Contents of RRC CONNECTION SETUP message: UM" is used with the following exceptions:
Contents of RRC CONNECTION SETUP message: UM
|
Information Element |
Value/remark |
|
– Default DPCH Offset Value |
Arbitrary set to value 1536..306176 by step of 2560 (this corresponds to a 0.5 slot timing offset between the DPCCH and the HS-DPCCH) |
7.3.20 Test procedure for TX, RX and Performance Requirement for UL OLTD with HSDPA & E-DCH
7.3.20.1 Initial conditions
System Simulator:
– 1 HS-DSCH plus E-DCH cell, default parameters.
User Equipment:
– The UE shall initially be operated under normal RF test conditions if not otherwise stated in the initial conditions for the actual test case.
– The Test-USIM shall be inserted.
– The UE has a valid TMSI (CS) after the execution of the procedure described in clause 7.2.2.1.
– The UE has a valid P-TMSI (PS) after the execution of the procedure described in clause 7.2.2.2.
7.3.20.2 Definition of system information messages
The default system information messages specified in clause 6.1.0b are used with the following exceptions.
Contents of System information block type 1: RRC
|
Information Element |
Value/remark |
|---|---|
|
– CN domain system information |
|
|
– CN domain identity |
PS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00 00 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– CN domain identity |
CS |
|
– CHOICE CN Type |
GSM-MAP |
|
– CN domain specific NAS system information |
|
|
– GSM-MAP NAS system information |
00(T3212 is set to infinity) 01 |
|
– CN domain specific DRX cycle length coefficient |
7 |
|
– UE Timers and constants in connected mode |
|
|
– T305 |
Infinity |
Contents of System information block type 3 and 4: RRC
|
Information Element |
Value/remark |
|
– Qrxlevmin |
-115 |
Contents of System Information Block type 5 (FDD)
|
Information Element |
Value/remark |
|
– Secondary CCPCH system information |
|
|
– Secondary CCPCH info |
|
|
– CHOICE mode |
FDD |
|
– Secondary scrambling code |
Not Present |
|
– STTD indicator |
FALSE |
|
– Spreading factor |
64 |
|
– Code number |
2 |
|
– Pilot symbol existence |
FALSE |
|
– TFCI existence |
TRUE (default value) |
|
– Fixed or Flexible position |
Flexible (default value) |
|
– Timing offset |
Not Present Absence of this IE is equivalent to default value 0 |
7.3.20.3 Procedure
|
Step |
Direction |
Message |
Comments |
|
|
UE |
SS |
|||
|
1 |
|
SYSTEM INFORMATION (BCCH) |
Broadcast |
|
|
2 |
|
PAGING TYPE1 (PCCH) |
Paging (CS domain, TMSI) |
|
|
3 |
|
RRC CONNECTION REQUEST (CCCH) |
RRC |
|
|
4 |
|
RRC CONNECTION SETUP (CCCH) |
RRC |
|
|
5 |
|
RRC CONNECTION SETUP COMPLETE (DCCH) |
RRC |
|
|
6 |
|
PAGING RESPONSE |
RR |
|
|
7 |
|
AUTHENTICATION REQUEST |
MM |
|
|
8 |
|
AUTHENTICATION RESPONSE |
MM |
|
|
9 |
|
SECURITY MODE COMMAND |
RRC (CS domain) |
|
|
10 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
11 |
|
PAGING TYPE2 (DCCH) |
Paging (TMSI (GSM-MAP)/ P-TMSI) |
|
|
12 |
|
SERVICE REQUEST |
GMM |
|
|
13 |
|
AUTHENTICATION AND CIPHERING REQUEST |
GMM |
|
|
14 |
|
AUTHENTICATION AND CIPHERING RESPONSE |
GMM |
|
|
15 |
|
SECURITY MODE COMMAND |
RRC (PS domain, IE Integrity protection mode command set to "modify") |
|
|
16 |
|
SECURITY MODE COMPLETE |
RRC |
|
|
17 |
|
ACTIVATE RB TEST MODE |
TC |
|
|
18 |
|
ACTIVATE RB TEST MODE COMPLETE |
TC |
|
|
19 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP RMC 12.2 CS) |
|
|
20 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
21 |
|
RADIO BEARER SETUP |
RRC (RAB SETUP HSDPA and E-DCH PS) |
|
|
22 |
|
RADIO BEARER SETUP COMPLETE |
RRC |
|
|
A23 |
|
CLOSE UE TEST LOOP (DCCH) |
TC (UE test loop mode set up to loop the RMC 12.2 to UL RMC 12.2). Test steps A23, A24, A26 and A27 are only executed when the test method in TS 34.121 [2] specifies that loopback test shall be used. |
|
|
A24 |
|
CLOSE UE TEST LOOP COMPLETE |
TC (confirms that loopback entities for the radio bearer(s) have been created and loop back is activated) |
|
|
25 |
<–> |
Perform test |
||
|
A26 |
|
OPEN UE TEST LOOP |
TC |
|
|
A27 |
|
OPEN UE TEST LOOP COMPLETE |
TC |
|
|
28 |
|
RRC CONNECTION RELEASE |
RRC |
|
|
29 |
|
RRC CONNECTION RELEASE COMPLETE |
RRC |
|
7.3.20.4 Specific message contents
The default message contents specified in clause 9.2 are used with the following exceptions.
7.3.20.4.1 ATTACH ACCEPT
This message is sent from the SS to the UE.
Contents of Attach Accept message: GMM
|
Information Element |
Value/remark |
|
Periodic RA update timer |
E0 (timer is deactivated) |
7.3.20.4.2 RADIO BEARER SETUP
For step 19, the message in clause 9.2, "Contents of RADIO BEARER SETUP message: AM or UM (Test Loop Mode1)" is used with condition A1. For step 21, the message in clause 9.2, "Contents of RADIO BEARER SETUP message: AM or UM (E-DCH and HSDPA)" is used, with following exceptions.
|
Information Element |
Value/remark |
Version |
|---|---|---|
|
Uplink OLTD info FDD |
Rel-11 |
|
|
– Uplink OLTD activation |
TRUE |
|
Information Element |
Value/remark |
Version |
|---|---|---|
|
F-TPICH Info |
Rel-11 |
|
|
– F-TPICH slot format |
1 |
|
|
– F-TPICH Code number |
6 |
|
|
– F-TPICH frame offset |
1024 |
The configurations of the fixed reference channels for HSPA RF tests are described in 3GPP TS 34.121[2], annex C for FDD and 3GPP TS 34.122 [5], annex C for TDD.
7.3.20.4.3 RRC CONNECTION SETUP
For step 4, the message in clause 9.2, "Contents of RRC CONNECTION SETUP message: UM" is used with the following exceptions:
Contents of RRC CONNECTION SETUP message: UM
|
Information Element |
Value/remark |
|
– Default DPCH Offset Value |
Arbitrary set to value 1536..306176 by step of 2560 (this corresponds to a 0.5 slot timing offset between the DPCCH and the HS-DPCCH) |