6.1.6 Reference Radio Conditions (TDD)
34.1083GPPCommon test environments for User Equipment (UE)Conformance testingRelease 15TS
The following transmission parameters shall be used for TDD modes other than 3.84 Mcps TDD IMB unless otherwise stated in the description of the individual test case.
Table 6.1.6a: Default settings for a serving cell in a single cell environment
|
Parameter |
Unit |
Cell 1/Cell 21/Cell 31 |
|
Cell type |
Serving cell |
|
|
UTRA RF Channel Number |
Mid Range Test Frequency |
|
|
Qrxlevmin |
dBm |
-81 |
|
UE_TXPWR_MAX_RACH |
dBm |
21 |
|
PCCPCH RSCP |
dBm |
-60 |
|
NOTE: The cell fulfils 3GPP TS 25.304 [36], clause 5.2.3.1.2 and 3GPP TS 25.123 [37]. |
||
Table 6.1.7: Default settings for a serving cell and
a suitable neighbour cell in a multi-cell environment
|
Parameter |
Unit |
Cell 1/Cell 21/Cell 31 |
Cell 2/Cell 22 |
Cell 4/Cell 24/Cell 32 |
|
Cell type |
Serving cell |
Suitable neighbour intra-frequency cell |
Suitable neighbour inter-frequency cell |
|
|
UTRA RF Channel Number |
Mid Range Test Frequency |
Mid Range Test Frequency |
High Range Test Frequency |
|
|
Qrxlevmin |
dBm |
-81 |
-81 |
|
|
UE_TXPWR_MAX_RACH |
dBm |
21 |
21 |
|
|
PCCPCH RSCP |
dBm |
-60 |
-70 |
|
|
NOTE: Both cells fulfil 3GPP TS 25.304 [36], clause 5.2.3.1.2 and 3GPP TS 25.123 [37]. |
||||
Table 6.1.8: Default settings for a non-suitable cell
|
Parameter |
Unit |
Level |
|
Qrxlevmin |
dBm |
-81 |
|
UE_TXPWR_MAX_RACH |
dBm |
21 |
|
PCCPCH RSCP |
dBm |
-91 |
|
NOTE: The cell is not suitable according to 3GPP TS 25.304 [36], clause 5.2.3.1.2. |
||
Table 6.1.9: Default settings for a non-suitable "Off" cell
|
Parameter |
Unit |
Level |
|
Qrxlevmin |
dBm |
-81 |
|
UE_TXPWR_MAX_RACH |
dBm |
21 |
|
PCCPCH RSCP |
dBm |
≤ -110 |
|
NOTE: The cell is not suitable according to 3GPP TS 25.304 [36], clause 5.2.3.1.2. |
||
Table 6.1.10: Default power levels of physical channels relative to P-CCPCH
|
Parameter |
Unit |
Level Idle mode |
Level Connected mode |
|
SCCPCH_Ec |
dB |
-2 |
|
|
FPACH_Ec |
dB |
-5 |
|
|
PICH_Ec |
dB |
-5 |
|
|
DPCH_Ec |
dB |
0 |
|
|
HS-SCCH_Ec |
dB |
0 |
|
|
E-AGCH_Ec |
dB |
-2 |
|
|
E-HICH |
dB |
-2 |
|
6.1.6.1 Reference Radio Conditions (3.84 Mcps TDD IMB)
The following transmission parameters shall be used unless otherwise stated in the description of the individual test case.
Table 6.1.6.3 gives the default settings for a non-suitable cell which is configured and always present whereas table 6.1.6.4 is for a cell that is switched off. Cells configured according to table 6.1.6.3 are for test cases in which it is necessary to make a cell unsuitable, and then subsequently make it suitable. This could be achieved by switching the cell off and then reconfiguring as in table 6.1.6.4, but this takes a lot of time to do.
Table 6.1.6.1: Default settings for a serving cell in a single cell environment
|
Parameter |
Unit |
Cell 31 |
|
Cell type |
Serving cell |
|
|
UTRA RF Channel Number (Note 2) |
Mid Range Test Frequency |
|
|
Qqualmin |
dB |
-24 |
|
Qrxlevmin |
dBm |
-79 |
|
UE_TXPWR_MAX_RACH |
dBm |
21 |
|
P-CPICH Ec (Note 1) |
dBm/3.84 MHz |
-60 |
|
T-CPICH Ec (Note 1) |
dBm/3.84 MHz |
-50.5 |
|
NOTE 1: The power level is specified in terms of CPICH_Ec instead of CPICH_RSCP as RSCP is a receiver measurement and only CPICH_Ec can be directly controlled by the SS. NOTE 2: The Test Frequencies are selected from the Tables in section 5.1.2 for the band under test. |
||
Table 6.1.6.2: Default settings for a serving cell and a suitable neighbour cell in a multi-cell environment
|
Parameter |
Unit |
Cell 31 |
Cell 33 |
|
Cell type |
Serving cell |
Suitable neighbour inter-frequency cell |
|
|
UTRA RF Channel Number |
Mid Range Test Frequency |
Mid Range Test Frequency |
|
|
Qqualmin |
dB |
-24 |
-24 |
|
Qrxlevmin |
dBm |
-79 |
-79 |
|
UE_TXPWR_MAX_RACH |
dBm |
21 |
21 |
|
P-CPICH Ec (Note 1) |
dBm/3.84 MHz |
-60 |
-70 |
|
T-CPICH Ec (Note 1) |
dBm/3.84 MHz |
-50.5 |
-60.5 |
|
NOTE 1: The power level is specified in terms of CPICH_Ec instead of CPICH_RSCP as RSCP is a receiver measurement and only CPICH_Ec can be directly controlled by the SS. |
|||
Table 6.1.6.3: Default settings for a non-suitable cell
|
Parameter |
Unit |
Level |
|
Qqualmin |
dB |
-24 |
|
Qrxlevmin |
dBm |
-79 |
|
UE_TXPWR_MAX_RACH |
dBm |
21 |
|
P-CPICH Ec (Note 1) |
dBm/3.84 MHz |
-90 |
|
T-CPICH Ec (Note 1) |
dBm/3.84 MHz |
-80.5 |
|
NOTE 1: The power level is specified in terms of CPICH_Ec instead of CPICH_RSCP as RSCP is a receiver measurement and only CPICH_Ec can be directly controlled by the SS. |
||
Table 6.1.6.4: Default settings for a non-suitable "Off" cell
|
Parameter |
Unit |
Level |
|
Qqualmin |
dB |
-24 |
|
Qrxlevmin |
dBm |
-79 |
|
P-CPICH_Ec (Note 1) |
dBm/3.84 MHz |
≤ -122 |
|
T-CPICH Ec (Note 1) |
dBm/3.84 MHz |
≤ -112.5 |
|
NOTE 1: The power level is specified in terms of CPICH_Ec instead of CPICH_RSCP as RSCP is a receiver measurement and only CPICH_Ec can be directly controlled by the SS. |
||
Table 6.1.6.5: Default power levels of physical channels relative to P-CPICH_Ec
|
Parameter |
Unit |
Level |
|
PCCPCH_Ec |
dB |
-2 |
|
SCCPCH_Ec (Note 2) |
dB |
-14 |
|
SCCPCH Type 2_Ec |
dB |
-2.57 |
|
SCH_Ec |
dB |
-5 |
|
T-CPICH |
dB |
-2.22 |
|
MICH |
dB |
-14 |
|
NOTE 1: Relative power levels are stated per code. NOTE 2: In 3GPP TS 25.221[28], clause 5.8.2.4, SCCPCH is referred to as SCCPCH Type 1. |
||