4.18 Measurements related to the UTRAN cell FDD carrier (RF Performance metrics)

32.4053GPPPerformance Management (PM)Performance measurementsRelease 17Telecommunication managementTSUniversal Terrestrial Radio Access Network (UTRAN)

4.18.0 Introduction

RF metrics can be used to indicate loading levels and abnormal conditions.

4.18.1 Mean Transmitted Carrier Power of an UTRAN Cell

  1. This measurement provides the average of the transmitted carrier power. This measurement is valid only for FDD mode.
  2. SI.
  3. This measurement is obtained by sampling at a pre-defined interval, the transmitted carrier power (see TS 25.133 [8]) for the RF carrier of a given UtranCell, and then taking the arithmetic mean.
  4. A single integer value from 0 to 100, that maps the value of the measured transmitted carrier power percentage as defined in table 9.43 [8].
  5. CARR.FDDMeanTCP.
  6. UtranCellFDD
  7. Valid for circuit switched and packet switched traffic
  8. UMTS
  9. Network Operator’s Traffic Engineering Community, Equipment Vendor’s Performance Modelling Community.

4.18.2 Maximum Transmitted Carrier Power of an UTRAN Cell

  1. This measurement provides the maximum of the transmitted carrier power. This measurement is valid only for FDD mode.
  2. SI.
  3. This measurement is obtained by sampling at a pre-defined interval, the transmitted carrier power (see TS 25.133 [8]) for the RF carrier of a given UtranCell, and then taking the maximum value.
  4. A single integer value from 0 to 100, that maps the value of the measured transmitted carrier power percentage as defined in table 9.43 [8].
  5. CARR.FDDMaxTCP.
  6. UtranCellFDD
  7. Valid for circuit switched and packet switched traffic
  8. UMTS
  9. Network Operator’s Traffic Engineering Community, Equipment Vendor’s Performance Modelling Community.

4.18.3 Mean Received Total Wideband Power of an UTRAN Cell

  1. This measurement provides the average of the received total wideband power. This measurement is valid only for FDD mode.
  2. SI.
  3. This measurement is obtained by sampling at a pre-defined interval, the received total wideband power (see TS 25.133 [8]) for the RF carrier of a given UtranCell, and then taking the arithmetic mean.
  4. A single integer value from 0 to 621 that maps the value of the measured received total wideband power as defined In table 9.37[8].
  5. CARR.FDDMeanRTWP.
  6. UtranCellFDD
  7. Valid for circuit switched and packet switched traffic
  8. UMTS
  9. Network Operator’s Traffic Engineering Community, Equipment Vendor’s Performance Modelling Community.

4.18.4 Maximum Received Total Wideband Power of an UTRAN Cell

  1. This measurement provides the maximum of the received total wideband power. This measurement is valid only for FDD mode.
  2. SI.
  3. This measurement is obtained by sampling at a pre-defined interval, the received wideband power (see TS 25.133 [8]) for the RF carrier of a given UtranCell, and then taking the maximum value.
  4. A single integer value from 0 to 621 that maps the value of the measured received total wideband power as defined In table 9.37[8]
  5. CARR.FDDMaxRTWP.
  6. UtranCellFDD
  7. Valid for circuit switched and packet switched traffic
  8. UMTS
  9. Network Operator’s Traffic Engineering Community, Equipment Vendor’s Performance Modelling Community.

4.18.5 Mean Radio Link Transmitted Code Power of an UTRAN Cell

a) This measurement provides the average of the Radio Link Transmitted Code Power. This measurement is valid for only FDD mode.

b) SI

c) This measurement is obtained by sampling at a pre-defined interval, the Radio Link Transmitted Code Power of a given UtranCell, and then taking the arithmetic mean.

d) A single integer value from 10 to 122, that maps the value of the measured Transmitted Code Power as defined in table 9.46 of TS 25.133 [8].

e) CARR. MeanRadioLink

f) UtranCellFDD

g) Valid for circuit switched and packet switched traffic

h) UMTS

4.18.6 Maximum Radio Link Transmitted Code Power of an UTRAN Cell

a) This measurement provides the maximum of the Radio Link Transmitted Code Power. This measurement is valid only for FDD mode.

b) SI

c) This measurement is obtained by sampling at a pre-defined interval, the Radio Link Transmitted Code Power of a given UtranCell, and then taking the arithmetic maximum value.

d) A single integer value from 10 to 122, that maps the value of the measured Transmitted Code Power as defined in table 9.46 of TS 25.133 [8].

e) CARR. MaxRadioLink

f) UtranCellFDD

g) Valid for circuit switched and packet switched traffic

h) UMTS

4.18.7 Mean transmitted carrier power of all codes not used for HS-PDSCH, HS-SCCH, E-AGCH, E-RGCH or E-HICH transmission of an UTRAN Cell

  1. This measurement provides the mean transmitted non-HS carrier power of a serving HS-DSCH cell.
    This measurement is valid only for FDD mode.
  2. SI.
  3. This measurement is obtained by sampling at a pre-defined interval, the transmitted carrier power (extracted from NBAP common measurement report (see TS 25.215 [14], TS 25.433 [7])) of all codes not used for
    HS-PDSCH, HS-SCCH, E-AGCH, E-RGCH or E-HICH transmission of a given UtranCell, and then taking the arithmetic mean of the measurement values obtained during the granularity period.
  4. A single integer value from 0 to 100, that maps the value of the measured transmitted carrier power to a percentage as defined in table 9.64 (see TS 25.133 [8]).
  5. CARR.MeanFDDNonHSTCP.
  6. UtranCellFDD
  7. Valid for circuit switched and packet switched traffic
  8. UMTS

4.18.8 Maximum transmitted carrier power of all codes not used for HS-PDSCH, HS-SCCH, E-AGCH, E-RGCH or E-HICH transmission of an UTRAN Cell

  1. This measurement provides the maximum transmitted non-HS carrier power of a serving HS-DSCH cell. This measurement is valid only for FDD mode.
  2. SI.
  3. This measurement is obtained by sampling at a pre-defined interval, the transmitted carrier power (extracted from NBAP common measurement report (see TS 25.215 [14], TS 25.433 [7])) of all codes not used for HS-PDSCH, HS-SCCH, E-AGCH, E-RGCH or E-HICH transmission of a given UtranCell, and then taking the maximum of the measurement values obtained during the granularity period.
  4. A single integer value from 0 to 100, that maps the value of the measured transmitted carrier power to a percentage as defined in table 9.64 (see TS 25.133 [8]).
  5. CARR.MaxFDDNonHSTCP.
  6. UtranCellFDD
  7. Valid for circuit switched and packet switched traffic
  8. UMTS