7.3 Operator controlled PLMN selector handling

31.1213GPPRelease 16TSUICC-terminal interfaceUniversal Subscriber Identity Module (USIM) application test specification

7.3.1 UE recognising the priority order of the Operator controlled PLMN selector list.

7.3.1.1 Definition and applicability

The Operator controlled PLMN selector list gives in priority order the preferred OPLMNs on which the UE shall register if no network of the User controlled PLMN selector list is available. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFOPLMNwACT. Update and deletion of OPLMNs shall not be possible by the subscriber by the use of the PIN.

The registration attempts initiated by the UE accessing UTRAN depends on UE’s capabilities and can be one of the following:

I. registration procedures for Ues supporting CS or

II. registration procedures for Ues supporting PS or

III. registration procedures for Ues supporting CS/PS

7.3.1.2 Conformance requirement

When registering onto a VPLMN the UE shall take into account the priority of OPLMNs in the preferred list on the USIM.

– TS 22.011 [6], clause 3.2.2;

– TS 31.102 [4], clause 4.2.53.

7.3.1.3 Test purpose

To verify that the OPLMN with the higher priority (defined by its position in EFOPLMNwACT) takes precedence over the OPLMN with the lower priority when the UE performs a network selection.

7.3.1.4 Method of test

7.3.1.4.1 Initial conditions

For this test a USS (in case of a Terminal accessing UTRAN) or a SS (in case of a Terminal accessing a GERAN) is needed.

The USS (in case of a Terminal accessing UTRAN)/ SS (in case of a Terminal accessing a GERAN) transmits on two BCCHs, with the following network parameters:

– Attach/detach: disabled.

– LAI (MCC/MNC/LAC): 254/011/0001.

– RAI (MCC/MNC/LAC/RAC): 254/011/0001/05 (for UTRAN cell only).

– Access control: unrestricted.

– Attach/detach: disabled.

– LAI (MCC/MNC/LAC): 254/012/0001.

– RAI (MCC/MNC/LAC/RAC): 254/012/0001/05 (for UTRAN cell only).

– Access control: unrestricted.

NOTE: In case of a GERAN no packet system information is transmitted.

The default UICC is used with the following exceptions:

EFUST (USIM Service Table)

Logically: Local Phone Book available

User controlled PLMN selector available

Fixed dialling numbers available

Barred dialling numbers available

The GSM Access available

The Group Identifier level 1 and level 2 not available

Service n 33 (Packed Switched Domain) shall be set to ‘1’

Enabled Services Table available

Operator controlled PLMN selector available

Coding:

B1

B2

B3

B4

B5

B6

binary

xx1x xx11

xxxx xxxx

xxxx 1×00

xxxx x1xx

xxxx xx11

xxxx xx1x

The coding of EFUST shall conform with the capabilities of the USIM used.

EFOPLMNwACT (OPLMN Selector)

Logically: 1st PLMN: 254 012 (MCC MNC)

1st ACT UTRAN

2nd PLMN: 254 011

2nd ACT UTRAN

3rd PLMN: 254 002

3rd ACT: UTRAN

4th PLMN: 254 012

4th ACT: GSM

5th PLMN: 254 011

5th ACT: GSM

6th PLMN: 254 005

6th ACT: UTRAN

7th PLMN: 254 006

7th ACT: UTRAN

8th PLMN: 254 007

8th ACT: UTRAN

Coding:

B01

B02

B03

B04

B05

B06

B07

B08

B09

B10

Hex

52

24

10

80

00

52

14

10

80

00

B11

B12

B13

B14

B15

B16

B17

B18

B19

B20

52

24

00

80

00

52

24

10

00

80

B21

B22

B23

B24

B25

B26

B27

B28

B29

B30

52

14

10

00

80

52

54

00

80

00

B31

B32

B33

B34

B35

B36

B37

B38

B39

B40

52

64

00

80

00

52

74

00

80

00

The UICC is installed into the Terminal and the UE is set to automatic PLMN selection mode.

In case of a Terminal accessing UTRAN "Expected Sequence A" and in case of a Terminal accessing a GERAN "Expected Sequence B" shall be performed.

7.3.1.4.2 Procedure

Expected Sequence A:

a) The UE is powered on.

b) After receipt on the cell related to the BCCH transmitting MCC/MNC 254/012 of a RRC CONNECTION REQUEST from the UE, the USS sends RRC CONNECTION SETUP to the UE, followed by RRC CONNECTION SETUP COMPLETE sent by the UE to the USS.

c) Depending on which domain the UE is going to be registered on, one of the following requirements should be fulfilled:

I. During registration on CS and after receipt of a LOCATION UPDATING REQUEST from the UE, the USS initiates authentication, starts integrity by using the security procedure and sends LOCATION UPDATING ACCEPT to the UE with the following values:

LAI (MCC/MNC/LAC): 254/012/0001

TMSI: "34567890"

II. During registration on PS and after receipt of a ATTACH REQUEST from the UE, the USS initiates authentication, starts integrity by using the security procedure and sends ATTACH ACCEPT to the UE with following values:

RAI (MCC/MNC/LAC/RAC) 254/012/0001/05

P-TMSI "34567890"

P-TMSI signature value "AB1234"

III. During registration on CS/PS and after receipt of a LOCATION UPDATING REQUEST and/or ATTACH REQUEST from the UE, the USS initiates authentication, starts integrity by using the security procedure and sends LOCATION UPDATING ACCEPT and/or ATTACH ACCEPT to the UE with some of the following values:

LAI (MCC/MNC/LAC): 254/012/0001

TMSI: "34567890"

RAI (MCC/MNC/LAC/RAC) 254/012/0001/05

P-TMSI "34567890"

P-TMSI signature value "AB1234"

d) After receipt of a

I. TMSI REALLOCATION COMPLETE during registration on CS from the UE, the USS sends RRC CONNECTION RELEASE to the UE, followed by RRC CONNECTION RELEASE COMPLETE sent by the UE to the USS.

II. ATTACH COMPLETE during registration on PS from the UE, the USS sends RRC CONNECTION RELEASE, followed by RRC CONNECTION RELEASE COMPLETE sent by the UE to the USS or.

III. TMSI REALLOCATION COMPLETE and/or ATTACH COMPLETE during registration on CS/PS from the UE, the USS sends RRC CONNECTION RELEASE, followed by RRC CONNECTION RELEASE COMPLETE sent by the UE to the USS.

e) The UE is soft powered down.

Expected Sequence B:

a) The UE is powered on.

b) After receipt of a CHANNEL REQUEST from the UE, the SS sends IMMEDIATE ASSIGNMENT to the UE.

c) After receipt of a LOCATION UPDATING REQUEST from the UE, the SS sends LOCATION UPDATING ACCEPT with:

LAI (MCC/MNC/LAC): 254/012/0001

TMSI: "34567890"

to the UE.

d) After receipt of a TMSI REALLOCATION COMPLETE from the UE, the SS sends CHANNEL RELEASE to the UE.

e) The UE is soft powered down.

7.3.1.5 Acceptance criteria

1) After step a) the UE accessing a GERAN shall send CHANNEL REQUEST on the cell related to the BCCH transmitting MCC/MNC 254/012 to the SS and the UE accessing UTRAN shall send an RRC CONNECTION REQUEST on the cell related to the BCCH transmitting MCC/MNC 254/012 to the USS.

2) After step b) the UE accessing a GERAN shall send LOCATION UPDATING REQUEST to the SS and the UE accessing UTRAN shall send

I. LOCATION UPDATING REQUEST to the USS during registration on CS or

II. ATTACH REQUEST. To the USS during registration on PS or

III. LOCATION UPDATING REQUEST and/or ATTACH REQUEST to the USS during registration on CS/PS.

3) After step c) the UE accessing GERAN shall respond with TMSI REALLOCATION COMPLETE and the UE accessing UTRAN shall respond with

I. TMSI REALLOCATION COMPLETE during registration on CS or

II. ATTACH COMPLETE during registration on PS or

III. TMSI REALLOCATION COMPLETE and/or ATTACH COMPLETE to the USS during registration on CS/PS.

4) After step e) the USIM shall contain the following values:

For UEs accessing GERAN and UEs accessing UTRAN and supporting (CS and PS) or (CS only):

EFLOCI (Location Information)

Logically: LAI-MCC: 254

LAI-MNC: 012

TMSI: "34567890"

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

B9

B10

B11

Hex

34

56

78

90

52

24

10

xx

xx

xx

00

For UEs supporting (CS and PS) or (PS only):

EFPSLOCI (Location Information)

Logically: RAI-MCC: 254

RAI-MNC: 012

P-TMSI: "34567890"

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

B9

B10

B11

Hex

34

56

78

90

xx

xx

xx

52

24

10

xx

Coding:

B12

B13

B14

Hex

xx

xx

00

7.3.2 UE recognising the priority order of the User controlled PLMN selector over the Operator controlled PLMN selector list.

7.3.2.1 Definition and applicability

The User controlled PLMN selector list has a higher priority as the OPLMN selector list on which the UE shall register. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFPLMNwACT.

The registration attempts initiated by the terminal accessing UTRAN depends on terminal’s capabilities and can be one of the following:

I. registration procedures for Ues supporting CS or

II. registration procedures for Ues supporting PS or

III. registration procedures for Ues supporting CS/PS

7.3.2.2 Conformance requirement

When registering onto a VPLMN the UE shall take into account the priority of UPLMNs first before the OPLMNs in the preferred list on the USIM.

– TS 22.011 [6], clause 3.2.2.2;

– TS 31.102 [4], clauses 4.2.5 and 4.2.53.

7.3.2.3 Test purpose

To verify that the User controlled PLMN with a lower priority (defined by its position in EFPLMNwACT) takes precedence over the OPLMN with a higher priority when the UE performs a network selection.

7.3.2.4 Method of test

7.3.2.4.1 Initial conditions

For this test a USS (in case of a Terminal accessing UTRAN) or a SS (in case of a Terminal accessing a GERAN) is needed.

The USS (in case of a Terminal accessing UTRAN)/ SS (in case of a Terminal accessing a GERAN) transmits on two BCCHs, with the following network parameters:

– Attach/detach: disabled.

– LAI (MCC/MNC/LAC): 254/001/0001.

– RAI (MCC/MNC/LAC/RAC): 254/001/0001/05 (only for UTRAN cell).

– Access control: unrestricted.

– Attach/detach: disabled.

– LAI (MCC/MNC/LAC): 244/010/0001.

– RAI (MCC/MNC/LAC/RAC): 244/010/0001/05 (only for UTRAN cell).

– Access control: unrestricted.

NOTE: In case of a GERAN no packet system information is transmitted

The default UICC is used with the following exception:

EFUST (USIM Service Table)

Logically: Local Phone Book available

User controlled PLMN selector available

Fixed dialling numbers available

Barred dialling numbers available

The GSM Access available

The Group Identifier level 1 and level 2 not available

Service n 33 (Packed Switched Domain) shall be set to ‘1’

Enabled Services Table available

Operator controlled PLMN selector available

Coding:

B1

B2

B3

B4

B5

B6

binary

xx1x xx11

xxxx xxxx

xxxx 1×00

xxxx x1xx

xxxx xx11

xxxx xx1x

The coding of EFUST shall conform with the capabilities of the USIM used.

EFPLMNwACT (UPLMN Selector with Access Technology)

Logically: 1st PLMN: 244 081 (MCC MNC)

1st ACT: UTRAN

2nd PLMN: 244 081

2nd ACT: GSM

3rd PLMN: 244 082

3rd ACT: UTRAN

4th PLMN: 244 082

4th ACT: GSM

5th PLMN: 244 003

5th ACT: UTRAN

6th PLMN: 244 004

6th ACT: UTRAN

7th PLMN: 244 005

7th ACT: UTRAN

8th PLMN: 244 006

8th ACT: UTRAN

9th PLMN: 244 007

9th ACT: UTRAN

10th PLMN: 244 008

10th ACT: UTRAN

11th PLMN: 244 010

11th ACT: UTRAN

12th PLMN: 244 010

12th ACT: GSM

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

B9

B10

B11

B12

B13

B14

B15

Hex

42

14

80

80

00

42

14

80

00

80

42

24

80

80

00

B16

B17

B18

B19

B20

B21

B22

B23

B24

B25

B26

B27

B28

B29

B30

42

24

80

00

80

42

24

00

80

00

42

44

00

80

00

B31

B32

B33

B34

B35

B36

B37

B38

B39

B40

B41

B42

B43

B44

B45

42

54

00

80

00

42

64

00

80

00

42

74

00

80

00

B46

B47

B48

B49

B50

B51

B52

B53

B54

B55

B56

B57

B58

B59

B60

42

84

00

80

00

42

04

10

80

00

42

04

10

00

80

The UICC is installed into the Terminal and the UE is set to automatic PLMN selection mode.

In case of a Terminal accessing UTRAN "Expected Sequence A" and in case of a Terminal accessing a GERAN "Expected Sequence B" shall be performed.

7.3.2.4.2 Procedure

Expected Sequence A:

a) The UE is powered on.

b) After receipt of a RRC CONNECTION REQUEST from the UE on the cell related to the BCCH transmitting MCC/MNC 244/010, the USS sends RRC CONNECTION SETUP to the UE, followed by RRC CONNECTION SETUP COMPLETE sent by the UE to the USS.

c) Depending on which domain the UE is going to be registered on, one of the following requirements should be fulfilled:

I. During registration on CS and after receipt of a LOCATION UPDATING REQUEST from the UE, the USS initiates authentication, starts integrity by using the security procedure and sends LOCATION UPDATING ACCEPT to the UE with the following values:

LAI (MCC/MNC/LAC): 244/010/0001

TMSI: "34567890"

II. During registration on PS and after receipt of a ATTACH REQUEST from the UE, the USS initiates authentication, starts integrity by using the security procedure and sends ATTACH ACCEPT with the following values:

RAI (MCC/MNC/LAC/RAC) 244/010/0001/05

P-TMSI "34567890"

P-TMSI signature value "AB1234"

III. During registration on CS/PS and after receipt of a LOCATION UPDATING REQUEST and/or ATTACH REQUEST from the UE, the USS initiates authentication, starts integrity by using the security procedure and sends LOCATION UPDATING ACCEPT and/or ATTACH ACCEPT with some of the following values :

LAI (MCC/MNC/LAC): 244/010/0001

TMSI: "34567890"

RAI (MCC/MNC/LAC/RAC) 244/010/0001/05

P-TMSI "34567890"

P-TMSI signature value "AB1234"

d) After receipt of a

I. TMSI REALLOCATION COMPLETE during registration on CS from the UE, the USS sends RRC CONNECTION RELEASE to the UE, followed by RRC CONNECTION RELEASE COMPLETE sent by the UE to the USS.

II. ATTACH COMPLETE during registration on PS from the UE, the USS sends RRC CONNECTION RELEASE, followed by RRC CONNECTION RELEASE COMPLETE sent by the UE to the USS or.

III. TMSI REALLOCATION COMPLETE and/or ATTACH COMPLETE during registration on CS/PS from the UE, the USS sends RRC CONNECTION RELEASE, followed by RRC CONNECTION RELEASE COMPLETE sent by the UE to the USS.

e) The UE is soft powered down.

Expected Sequence B:

a) The UE is powered on.

b) After receipt of a CHANNEL REQUEST from the UE, the SS sends IMMEDIATE ASSIGNMENT to the UE.

c) After receipt of a LOCATION UPDATING REQUEST from the UE, the SS sends LOCATION UPDATING ACCEPT with:

LAI (MCC/MNC/LAC): 244/010/0001

TMSI: "34567890"

to the UE.

d) After receipt of a TMSI REALLOCATION COMPLETE from the UE, the SS sends CHANNEL RELEASE to the UE.

e) The UE is soft powered down.

7.3.2.5 Acceptance criteria

1) After step a) the UE accessing a GERAN shall send CHANNEL REQUEST on the cell related to the BCCH transmitting MCC/MNC 244/010 to the SS and the UE accessing UTRAN shall send an RRC CONNECTION REQUEST on the cell related to the BCCH transmitting MCC/MNC 244/010 to the USS.

2) After step b) the UE accessing a GERAN shall send LOCATION UPDATING REQUEST to the SS and the UE accessing UTRAN shell send

I. LOCATION UPDATING REQUEST to the USS during registration on CS or

II. ATTACH REQUEST during registration on PS or

III. LOCATION UPDATING REQUEST and/or ATTACH REQUEST to the USS during registration on CS/PS.

3) After step c) the UE accessing GERAN shall respond with TMSI REALLOCATION COMPLETE and the UE accessing UTRAN shall respond with

I. TMSI REALLOCATION COMPLETE during registration on CS or

II. ATTACH COMPLETE during registration on PS or

III. TMSI REALLOCATION COMPLETE and/or ATTACH COMPLETE to the USS during registration on CS/PS..

4) After step e) the USIM shall contain the following values:

For UEs accessing GERAN and UEs accessing UTRAN and supporting (CS and PS) or (CS only):

EFLOCI (Location Information)

Logically: LAI-MCC: 244

LAI-MNC: 010

TMSI: "34567890"

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

B9

B10

B11

34

56

78

90

42

04

10

xx

xx

xx

00

For UEs supporting (CS and PS) or (PS only):

EFPSLOCI (Location Information)

Logically: RAI-MCC: 244

RAI-MNC: 010

P-TMSI: "34567890"

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

B9

B10

B11

Hex

34

56

78

90

xx

xx

xx

42

04

10

xx

Coding:

B12

B13

B14

Hex

xx

xx

00

7.3.3 UE recognising the priority order of the Operator controlled PLMN selector list when accessing E-UTRAN

7.3.3.1 Definition and applicability

The Operator controlled PLMN selector list gives in priority order the preferred OPLMNs on which the UE shall register if no network of the User controlled PLMN selector list is available. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFOPLMNwACT. Update and deletion of OPLMNs shall not be possible by the subscriber by the use of the PIN.

7.3.3.2 Conformance requirement

When registering onto a VPLMN the UE shall take into account the priority of OPLMNs in the preferred list on the USIM.

– TS 22.011 [6], clause 3.2.2;

– TS 31.102 [4], clause 4.2.53, 4.2.5 and 5.1.1.2.

7.3.3.3 Test purpose

To verify that the OPLMN with the higher priority (defined by its position in EFOPLMNwACT) takes precedence over the OPLMN with the lower priority when the UE performs a network selection. Hereby the new coding for RAT
E-UTRAN/NB-IoT has to be handled correctly by the UE.

7.3.3.4 Method of test

7.3.3.4.1 Initial conditions

For this test an E-USS/NB-SS is required.

The E-USS transmits on two BCCHs, with the following network parameters:

– TAI (MCC/MNC/TAC): 254/011/0001.

– Access control: unrestricted.

– TAI (MCC/MNC/TAC): 254/012/0001.

– Access control: unrestricted.

The NB-SS transmits on two BCCHs, with the following network parameters:

– TAI (MCC/MNC/TAC): 254/011/0001.

– Access control: unrestricted.

– TAI (MCC/MNC/TAC): 254/012/0001.

– Access control: unrestricted.

The default E-UTRAN UICC is used with the following exceptions:

EFUST (USIM Service Table)

Logically: Local Phone Book available

User controlled PLMN selector available

Fixed dialling numbers available

Barred dialling numbers available

The GSM Access available

The Group Identifier level 1 and level 2 not available

Service n 33 (Packed Switched Domain) shall be set to ‘1’

Enabled Services Table available

Operator controlled PLMN selector available

EPS Mobility Management Information available

Allowed CSG Lists and corresponding indications not available

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

Binary

xx1x xx11

xxxx xxxx

xxxx 1×00

xxxx x1xx

xxxx xx11

xxxx xx1x

xxxx xxxx

xxxx xxxx

B9

B10

B11

xxxx xxxx

xxxx xxxx

xx01 xxxx

The coding of EFUST shall conform with the capabilities of the USIM used.

EFOPLMNwACT (OPLMN Selector)

Logically: 1st PLMN: 254 012 (MCC MNC)

1st ACT E-UTRAN

2nd PLMN: 254 011

2nd ACT E-UTRAN

3rd PLMN: 254 002

3rd ACT: E-UTRAN

4th PLMN: 254 012

4th ACT: GSM

5th PLMN: 254 011

5th ACT: GSM

6th PLMN: 254 005

6th ACT: UTRAN

7th PLMN: 254 006

7th ACT: UTRAN

8th PLMN: 254 007

8th ACT: UTRAN

Coding:

B01

B02

B03

B04

B05

B06

B07

B08

B09

B10

Hex

52

24

10

40

00

52

14

10

40

00

B11

B12

B13

B14

B15

B16

B17

B18

B19

B20

52

24

00

40

00

52

24

10

00

80

B21

B22

B23

B24

B25

B26

B27

B28

B29

B30

52

14

10

00

80

52

54

00

80

00

B31

B32

B33

B34

B35

B36

B37

B38

B39

B40

52

64

00

80

00

52

74

00

80

00

The UICC is installed into the Terminal and the UE is set to automatic PLMN selection mode.

7.3.3.4.2 Procedure

a) The UE is powered on.

b) After receipt of an RRCConnectionRequest/RRCConnectionRequest-NB from the UE on the E-UTRAN-cell/NB-IoT-cell related to the BCCH transmitting MCC/MNC 254/012, the E-USS/NB-SS sends RRCConnectionSetup/RRCConnectionSetup-NB to the UE, followed by RRCConnectionSetupComplete/RRCConnectionSetupComplete-NB sent by the UE to the E-USS/NB-SS.

c) During registration and after receipt of a AttachRequest from the UE, the E-USS/NB-SS initiates authentication, starts integrity by using the security procedure and sends AttachAccept with to the UE:

TAI (MCC/MNC/TAC): 254/012/ 0001

GUTI: "25401200010266436587"

d) After receipt of the AttachComplete during registration from the UE, the E-USS/NB-SS sends RRCConnectionRelease/RRCConnectionRelease-NB.

e) The UE is soft powered down.

7.3.3.5 Acceptance criteria

1.) After step a) the UE shall send a RRCConnectionRequest/RRCConnectionRequest-NB on the E-UTRAN-cell/NB-IoT-cell related to the BCCH transmitting MCC/MNC 254/012 to the E-USS/NB-SS.

2) After step b) the terminal shall send AttachRequest to the E-USS/NB-SS.

3) After step c) the terminal shall respond with AttachComplete during registration.

4) After step e) the USIM shall contain the following values:

EFEPSLOCI (EPS Information)

Logically: GUTI: 25401200010266436587

Last visited registered TAI: 254/012/0001

EPS update status: updated

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

B9

B10

B11

Hex

0B

F6

52

24

10

00

01

02

66

43

65

B12

B13

B14

B15

B16

B17

B18

87

52

24

10

00

01

00

7.3.4 UE recognising the priority order of the User controlled PLMN selector over the Operator controlled PLMN selector list – E-UTRAN

7.3.4.1 Definition and applicability

The User controlled PLMN selector list has a higher priority as the OPLMN selector list on which the UE shall register. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFPLMNwACT.

7.3.4.2 Conformance requirement

When registering onto a VPLMN the UE shall take into account the priority of UPLMNs first before the OPLMNs in the preferred list on the USIM.

– TS 22.011 [6], clause 3.2.2.2;

– TS 31.102 [4], clauses 4.2.5, 4.2.53 and 5.1.1.2.

7.3.4.3 Test purpose

To verify that the User controlled PLMN with a lower priority (defined by its position in EFPLMNwACT) takes precedence over the OPLMN with a higher priority when the UE performs a network selection. Hereby the new coding for RAT
E-UTRAN/NB-IoT has to be handled correctly by the UE.

7.3.4.4 Method of test

7.3.4.4.1 Initial conditions

For this test an E-USS/NB-SS is required.

The E-USS transmits on two BCCHs, with the following network parameters:

– TAI (MCC/MNC/TAC): 254/001/0001.

— Access control: unrestricted.

– TAI (MCC/MNC/TAC): 244/010/0001.

– Access control: unrestricted.

The NB-SS transmits on two BCCHs, with the following network parameters:

– TAI (MCC/MNC/TAC): 254/001/0001.

— Access control: unrestricted.

– TAI (MCC/MNC/TAC): 244/010/0001.

– Access control: unrestricted.

The default E-UTRAN UICC is used with the following exception:

EFUST (USIM Service Table)

Logically: Local Phone Book available

User controlled PLMN selector available

Fixed dialling numbers available

Barred dialling numbers available

The GSM Access available

The Group Identifier level 1 and level 2 not available

Service n 33 (Packed Switched Domain) shall be set to ‘1’

Enabled Services Table available

Operator controlled PLMN selector available

EPS Mobility Management Information available

Allowed CSG Lists and corresponding indications not available

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

Binary

xx1x xx11

xxxx xxxx

xxxx 1×00

xxxx x1xx

xxxx xx11

xxxx xx1x

xxxx xxxx

xxxx xxxx

B9

B10

B11

xxxx xxxx

xxxx xxxx

xx01 xxxx

The UICC is installed into the Terminal and the UE is set to automatic PLMN selection mode.

7.3.4.4.2 Procedure

a) The UE is powered on.

b) After receipt of an RRCConnectionRequest/RRCConnectionRequest-NB from the UE on the E-UTRAN-cell/NB-IoT-cell related to the BCCH transmitting MCC/MNC 244/010, the E-USS/NB-SS sends RRCConnectionSetup/RRCConnectionSetup-NB to the UE, followed by RRCConnectionSetupComplete/RRCConnectionSetupComplete-NB sent by the UE to the E-USS/NB-SS.

c) During registration and after receipt of a AttachRequest from the UE, the E-USS/NB-SS initiates authentication, starts integrity by using the security procedure and sends AttachAccept with to the UE:

TAI (MCC/MNC/TAC): 244/010/ 0001

GUTI: "24401000010266436587"

d) After receipt of the AttachComplete during registration from the UE, the E-USS/NB-SS sends RRCConnectionRelease/RRCConnectionRelease-NB.

e) The UE is soft powered down.

7.3.4.5 Acceptance criteria

1.) After step a) the UE shall send a RRCConnectionRequest/RRCConnectionRequest-NB on the E-UTRAN-cell/NB-IoT-cell related to the BCCH transmitting MCC/MNC 244/010 to the E-USS/NB-SS.

2) After step b) the terminal shall send AttachRequest to the E-USS/NB-SS.

3) After step c) the terminal shall respond with AttachComplete during registration.

4) After step e) the USIM shall contain the following values:

EFEPSLOCI (EPS Information)

Logically: GUTI: 24401000010266436587

Last visited registered TAI: 244/010/0001

EPS update status: updated

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

B9

B10

B11

Hex

0B

F6

42

04

10

00

01

02

66

43

65

B12

B13

B14

B15

B16

B17

B18

87

42

04

10

00

01

00

7.3.5 UE recognising the priority order of the Operator controlled PLMN selector list when accessing E-UTRAN in NB-S1 mode

7.3.5.1 Definition and applicability

The Operator controlled PLMN selector list gives in priority order the preferred OPLMNs on which the UE shall register if no network of the User controlled PLMN selector list is available. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFOPLMNwACT. Update and deletion of OPLMNs shall not be possible by the subscriber by the use of the PIN.

7.3.5.2 Conformance requirement

When registering onto a VPLMN the UE shall take into account the priority of OPLMNs in the preferred list on the USIM.

– TS 22.011 [6], clause 3.2.2;

– TS 31.102 [4], clause 4.2.53, 4.2.5 and 5.1.1.2.

7.3.5.3 Test purpose

To verify that the OPLMN with the higher priority (defined by its position in EFOPLMNwACT) takes precedence over the OPLMN with the lower priority when the UE performs a network selection. Hereby the new coding for RAT
E-UTRAN in NB-IoT mode has to be handled correctly by the UE.

7.3.5.4 Method of test

7.3.5.4.1 Initial conditions

For this test a NB-SS is required.

The NB-SS transmits on two BCCHs, with the following network parameters:

– TAI (MCC/MNC/TAC): 254/011/0001.

– Access control: unrestricted.

– TAI (MCC/MNC/TAC): 254/012/0001.

– Access control: unrestricted.

The default E-UTRAN UICC is used with the following exceptions:

EFUST (USIM Service Table)

Logically: Local Phone Book available

User controlled PLMN selector available

Fixed dialling numbers available

Barred dialling numbers available

The GSM Access available

The Group Identifier level 1 and level 2 not available

Service n 33 (Packed Switched Domain) shall be set to ‘1’

Enabled Services Table available

Operator controlled PLMN selector available

EPS Mobility Management Information available

Allowed CSG Lists and corresponding indications not available

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

Binary

xx1x xx11

xxxx xxxx

xxxx 1×00

xxxx x1xx

xxxx xx11

xxxx xx1x

xxxx xxxx

xxxx xxxx

B9

B10

B11

xxxx xxxx

xxxx xxxx

xx01 xxxx

The coding of EFUST shall conform with the capabilities of the USIM used.

EFOPLMNwACT (OPLMN Selector)

Logically: 1st PLMN: 254 012 (MCC MNC)

1st ACT E-UTRAN in NB-S1 mode

2nd PLMN: 254 011

2nd ACT E-UTRAN in NB-S1 mode

3rd PLMN: 254 002

3rd ACT: E-UTRAN

4th PLMN: 254 012

4th ACT: GSM

5th PLMN: 254 011

5th ACT: GSM

6th PLMN: 254 005

6th ACT: UTRAN

7th PLMN: 254 006

7th ACT: UTRAN

8th PLMN: 254 007

8th ACT: UTRAN

Coding:

B01

B02

B03

B04

B05

B06

B07

B08

B09

B10

Hex

52

24

10

50

00

52

14

10

50

00

B11

B12

B13

B14

B15

B16

B17

B18

B19

B20

52

24

00

40

00

52

24

10

00

80

B21

B22

B23

B24

B25

B26

B27

B28

B29

B30

52

14

10

00

80

52

54

00

80

00

B31

B32

B33

B34

B35

B36

B37

B38

B39

B40

52

64

00

80

00

52

74

00

80

00

The UICC is installed into the Terminal and the UE is set to automatic PLMN selection mode.

7.3.5.4.2 Procedure

a) The UE is powered on.

b) After receipt of an RRCConnectionRequest-NB from the UE on the NB-IoT-cell related to the BCCH transmitting MCC/MNC 254/012, the NB-SS sends RRCConnectionSetup-NB to the UE, followed by RRCConnectionSetupComplete-NB sent by the UE to the NB-SS.

c) During registration and after receipt of a AttachRequest from the UE, the NB-SS initiates authentication, starts integrity by using the security procedure and sends AttachAccept with to the UE:

TAI (MCC/MNC/TAC): 254/012/ 0001

GUTI: "25401200010266436587"

d) After receipt of the AttachComplete during registration from the UE, the NB-SS sends RRCConnectionRelease-NB.

e) The UE is soft powered down.

7.3.5.5 Acceptance criteria

1.) After step a) the UE shall send a RRCConnectionRequest-NB on the NB-IoT-cell related to the BCCH transmitting MCC/MNC 254/012 to the NB-SS.

2) After step b) the terminal shall send AttachRequest to the NB-SS.

3) After step c) the terminal shall respond with AttachComplete during registration.

4) After step e) the USIM shall contain the following values:

EFEPSLOCI (EPS Information)

Logically: GUTI: 25401200010266436587

Last visited registered TAI: 254/012/0001

EPS update status: updated

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

B9

B10

B11

Hex

0B

F6

52

24

10

00

01

02

66

43

65

B12

B13

B14

B15

B16

B17

B18

87

52

24

10

00

01

00

7.3.6 UE recognising the priority order of the User controlled PLMN selector over the Operator controlled PLMN selector list – E-UTRAN in NB-S1 mode

7.3.6.1 Definition and applicability

The User controlled PLMN selector list has a higher priority as the OPLMN selector list on which the UE shall register. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFPLMNwACT.

7.3.6.2 Conformance requirement

When registering onto a VPLMN the UE shall take into account the priority of UPLMNs first before the OPLMNs in the preferred list on the USIM.

– TS 22.011 [6], clause 3.2.2.2;

– TS 31.102 [4], clauses 4.2.5, 4.2.53 and 5.1.1.2.

7.3.6.3 Test purpose

To verify that the User controlled PLMN with a lower priority (defined by its position in EFPLMNwACT) takes precedence over the OPLMN with a higher priority when the UE performs a network selection. Hereby the new coding for RAT
E-UTRAN in NB-IoT mode has to be handled correctly by the UE.

7.3.6.4 Method of test

7.3.6.4.1 Initial conditions

For this test a NB-SS is required.

The NB-SS transmits on two BCCHs, with the following network parameters:

– TAI (MCC/MNC/TAC): 254/001/0001.

— Access control: unrestricted.

– TAI (MCC/MNC/TAC): 244/010/0001.

– Access control: unrestricted.

The default E-UTRAN UICC is used with the following exception:

EFUST (USIM Service Table)

Logically: Local Phone Book available

User controlled PLMN selector available

Fixed dialling numbers available

Barred dialling numbers available

The GSM Access available

The Group Identifier level 1 and level 2 not available

Service n 33 (Packed Switched Domain) shall be set to ‘1’

Enabled Services Table available

Operator controlled PLMN selector available

EPS Mobility Management Information available

Allowed CSG Lists and corresponding indications not available

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

Binary

xx1x xx11

xxxx xxxx

xxxx 1×00

xxxx x1xx

xxxx xx11

xxxx xx1x

xxxx xxxx

xxxx xxxx

B9

B10

B11

xxxx xxxx

xxxx xxxx

xx01 xxxx

The UICC is installed into the Terminal and the UE is set to automatic PLMN selection mode.

EFPLMNwACT (User Controlled PLMN Selector with Access Technology)

Logically: 1st PLMN: 244 081 (MCC MNC)

1st ACT: E-UTRAN

2nd PLMN: 244 081

2nd ACT: GSM

3rd PLMN: 244 083

3rd ACT: E-UTRAN

4th PLMN: 244 082

4th ACT: GSM

5th PLMN: 244 003

5th ACT: E-UTRAN

6th PLMN: 244 004

6th ACT: UTRAN

7th PLMN: 244 005

7th ACT: UTRAN

8th PLMN: 244 081

8th ACT: UTRAN

9th PLMN: 244 007

9th ACT: UTRAN

10th PLMN: 244 008

10th ACT: E-UTRAN

11th PLMN: 244 009

11th ACT: UTRAN

12th PLMN: 244 010

12th ACT: E-UTRAN in NB-S1 mode

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

B9

B10

B11

B12

B13

B14

B15

Hex

42

14

80

40

00

42

14

80

00

80

42

34

80

40

00

B16

B17

B18

B19

B20

B21

B22

B23

B24

B25

B26

B27

B28

B29

B30

42

24

80

00

80

42

34

00

40

00

42

44

00

80

00

B31

B32

B33

B34

B35

B36

B37

B38

B39

B40

B41

B42

B43

B44

B45

42

54

00

80

00

42

14

80

80

00

42

74

00

80

00

B46

B47

B48

B49

B50

B51

B52

B53

B54

B55

B56

B57

B58

B59

B60

42

84

00

40

00

42

94

00

80

00

42

04

10

50

00

EFOPLMNwACT (Operator Controlled PLMN Selector with Access Technology)

Logically: 1st PLMN: 254 001 (MCC MNC)

1st ACT: E-UTRAN in NB-S1 mode

2nd PLMN: 254 001

2nd ACT: GSM

3rd PLMN: 254 002

3rd ACT: E-UTRAN

4th PLMN: 254 003

4th ACT: E-UTRAN

5th PLMN: 254 004

5th ACT: UTRAN

6th PLMN: 254 005

6th ACT: UTRAN

7th PLMN: 254 006

7th ACT: UTRAN

8th PLMN: 254 007

8th ACT: UTRAN

Coding:

B01

B02

B03

B04

B05

B06

B07

B08

B09

B10

Hex

52

14

00

50

00

52

14

00

00

80

B11

B12

B13

B14

B15

B16

B17

B18

B19

B20

52

24

00

40

00

52

34

00

40

00

B21

B22

B23

B24

B25

B26

B27

B28

B29

B30

52

44

00

80

00

52

54

00

80

00

B31

B32

B33

B34

B35

B36

B37

B38

B39

B40

52

64

00

80

00

52

74

00

80

00

7.3.6.4.2 Procedure

a) The UE is powered on.

b) After receipt of an RRCConnectionRequest-NB from the UE on the NB-IoT-cell related to the BCCH transmitting MCC/MNC 244/010, the NB-SS sends RRCConnectionSetup-NB to the UE, followed by RRCConnectionSetupComplete-NB sent by the UE to the NB-SS.

c) During registration and after receipt of a AttachRequest from the UE, the NB-SS initiates authentication, starts integrity by using the security procedure and sends AttachAccept with to the UE:

TAI (MCC/MNC/TAC): 244/010/ 0001

GUTI: "24401000010266436587"

d) After receipt of the AttachComplete during registration from the UE, the NB-SS sends RRCConnectionRelease-NB.

e) The UE is soft powered down.

7.3.6.5 Acceptance criteria

1.) After step a) the UE shall send a RRCConnectionRequest-NB on the NB-IoT-cell related to the BCCH transmitting MCC/MNC 244/010 to the NB-SS.

2) After step b) the terminal shall send AttachRequest to the NB-SS.

3) After step c) the terminal shall respond with AttachComplete during registration.

4) After step e) the USIM shall contain the following values:

EFEPSLOCI (EPS Information)

Logically: GUTI: 24401000010266436587

Last visited registered TAI: 244/010/0001

EPS update status: updated

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

B9

B10

B11

Hex

0B

F6

42

04

10

00

01

02

66

43

65

B12

B13

B14

B15

B16

B17

B18

87

42

04

10

00

01

00

7.3.7 UE recognising the priority order of the Operator controlled PLMN selector list using the ACT preference – E-UTRAN in NB-S1/ E-UTRAN in WB-S1 mode

7.3.7.1 Definition and applicability

The Operator controlled PLMN selector list gives in priority order the preferred OPLMNs on which the UE shall register if no network of the User controlled PLMN selector list is available. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFOPLMNwACT. Update and deletion of OPLMNs shall not be possible by the subscriber by the use of the PIN.

7.3.7.2 Conformance requirement

When registering onto a VPLMN the UE shall take into account the priority of OPLMNs in the preferred list on the USIM.

– TS 22.011 [6], clause 3.2.2;

– TS 31.102 [4], clause 4.2.53, 4.2.5 and 5.1.1.2.

7.3.7.3 Test purpose

To verify that the OPLMN with the higher priority (defined by its position in EFOPLMNwACT) takes precedence over the OPLMN with the lower priority when the UE performs a network selection. Hereby the new coding for RAT
E-UTRAN in NB-IoT mode and E-UTRAN in WB-S1 mode has to be handled correctly by the UE.

7.3.7.4 Method of test

7.3.7.4.1 Initial conditions

For this test an E-USS and NB-SS is required.

The E-USS transmits on BCCHs, with the following network parameters:

– TAI (MCC/MNC/TAC): 254/012/0001.

– Access control: unrestricted.

The NB-SS transmits on BCCHs, with the following network parameters:

– TAI (MCC/MNC/TAC): 254/012/0001.

– Access control: unrestricted.

The default E-UTRAN UICC is used with the following exceptions:

EFUST (USIM Service Table)

Logically: Local Phone Book available

User controlled PLMN selector available

Fixed dialling numbers available

Barred dialling numbers available

The GSM Access available

The Group Identifier level 1 and level 2 not available

Service n 33 (Packed Switched Domain) shall be set to ‘1’

Enabled Services Table available

Operator controlled PLMN selector available

EPS Mobility Management Information available

Allowed CSG Lists and corresponding indications not available

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

Binary

xx1x xx11

xxxx xxxx

xxxx 1×00

xxxx x1xx

xxxx xx11

xxxx xx1x

xxxx xxxx

xxxx xxxx

B9

B10

B11

xxxx xxxx

xxxx xxxx

xx01 xxxx

The coding of EFUST shall conform with the capabilities of the USIM used.

EFOPLMNwACT (OPLMN Selector)

Logically: 1st PLMN: 254 012 (MCC MNC)

1st ACT E-UTRAN in NB-S1 mode

2nd PLMN: 254 012

2nd ACT E-UTRAN in WB-S1 mode

3rd PLMN: 254 002

3rd ACT: E-UTRAN

4th PLMN: 254 012

4th ACT: GSM

5th PLMN: 254 011

5th ACT: GSM

6th PLMN: 254 005

6th ACT: UTRAN

7th PLMN: 254 006

7th ACT: UTRAN

8th PLMN: 254 007

8th ACT: UTRAN

Coding:

B01

B02

B03

B04

B05

B06

B07

B08

B09

B10

Hex

52

24

10

50

00

52

24

10

60

00

B11

B12

B13

B14

B15

B16

B17

B18

B19

B20

52

24

00

40

00

52

24

10

00

80

B21

B22

B23

B24

B25

B26

B27

B28

B29

B30

52

14

10

00

80

52

54

00

80

00

B31

B32

B33

B34

B35

B36

B37

B38

B39

B40

52

64

00

80

00

52

74

00

80

00

The UICC is installed into the Terminal and the UE is set to automatic PLMN selection mode.

7.3.7.4.2 Procedure

a) The UE is powered on.

b) After receipt of an RRCConnectionRequest-NB from the UE on the NB-IoT-cell related to the BCCH transmitting MCC/MNC 254/012, the NB-SS sends RRCConnectionSetup-NB to the UE, followed by RRCConnectionSetupComplete-NB sent by the UE to the NB-SS.

c) During registration and after receipt of a AttachRequest from the UE, the NB-SS initiates authentication, starts integrity by using the security procedure and sends AttachAccept with to the UE:

TAI (MCC/MNC/TAC): 254/012/ 0001

GUTI: "25401200010266436587"

d) After receipt of the AttachComplete during registration from the UE, the NB-SS sends RRCConnectionRelease-NB.

e) The UE is soft powered down.

7.3.7.5 Acceptance criteria

1.) After step a) the UE shall send a RRCConnectionRequest-NB on the NB-IoT-cell related to the BCCH transmitting MCC/MNC 254/012 to the NB-SS.

2) After step b) the terminal shall send AttachRequest to the NB-SS.

3) After step c) the terminal shall respond with AttachComplete during registration.

4) After step e) the USIM shall contain the following values:

EFEPSLOCI (EPS Information)

Logically: GUTI: 25401200010266436587

Last visited registered TAI: 254/012/0001

EPS update status: updated

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

B9

B10

B11

Hex

0B

F6

52

24

10

00

01

02

66

43

65

B12

B13

B14

B15

B16

B17

B18

87

52

24

10

00

01

00

7.3.8 UE recognising the priority order of the Operator controlled PLMN selector list using the ACT preference – E-UTRAN in NB-S1 mode/ GSM

7.3.8.1 Definition and applicability

The Operator controlled PLMN selector list gives in priority order the preferred OPLMNs on which the UE shall register if no network of the User controlled PLMN selector list is available. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFOPLMNwACT. Update and deletion of OPLMNs shall not be possible by the subscriber by the use of the PIN.

7.3.8.2 Conformance requirement

When registering onto a VPLMN the UE shall take into account the priority of OPLMNs in the preferred list on the USIM.

– TS 22.011 [6], clause 3.2.2;

– TS 31.102 [4], clause 4.2.53, 4.2.5 and 5.1.1.2.

7.3.8.3 Test purpose

To verify that the OPLMN with the higher priority (defined by its position in EFOPLMNwACT) takes precedence over the OPLMN with the lower priority when the UE performs a network selection. Hereby the new coding for RAT
E-UTRAN in NB-S1 mode has to be handled correctly by the UE.

7.3.8.4 Method of test

7.3.8.4.1 Initial conditions

For this test both a GSM SS and an NB-IoT NB-SS are needed.

The GSM SS transmits on BCCH, with the following network parameters:

– Attach/detach: disabled.

– LAI (MCC/MNC/LAC): 244/083/0001.

– Access control: unrestricted.

The NB-SS transmits on the BCCH, with the following network parameters:

– TAI (MCC/MNC/TAC): 244/083/0001.

– Access control: unrestricted.

The default E-UTRAN UICC is used with the following exception:

EFOPLMNwACT (Operator Controlled PLMN Selector with Access Technology)

Logically: 1st PLMN: 254 001 (MCC MNC)

1st ACT: E-UTRAN

2nd PLMN: 254 001

2nd ACT: GSM

3rd PLMN: 244 083

3rd ACT: E-UTRAN in NB-S1 mode

4th PLMN: 244 083

4th ACT: GSM

5th PLMN: 254 004

5th ACT: UTRAN

6th PLMN: 254 005

6th ACT: UTRAN

7th PLMN: 254 006

7th ACT: UTRAN

8th PLMN: 254 007

8th ACT: UTRAN

Coding:

B01

B02

B03

B04

B05

B06

B07

B08

B09

B10

Hex

52

14

00

40

00

52

14

00

00

80

B11

B12

B13

B14

B15

B16

B17

B18

B19

B20

42

34

80

50

00

42

34

80

00

80

B21

B22

B23

B24

B25

B26

B27

B28

B29

B30

52

44

00

80

00

52

54

00

80

00

B31

B32

B33

B34

B35

B36

B37

B38

B39

B40

52

64

00

80

00

52

74

00

80

00

The UICC is installed into the Terminal and the UE is set to automatic PLMN selection mode.

7.3.8.4.2 Procedure

a) The UE is powered on.

b) After receipt of an RRCConnectionRequest-NB from the UE on the NB-IoT-cell related to the BCCH transmitting MCC/MNC 244/083, the E-USS sends RRCConnectionSetup to the UE, followed by RRCConnectionSetupComplete-NB sent by the UE to the NB-SS.

c) During registration and after receipt of a AttachRequest from the UE, the NB-SS initiates authentication, starts integrity by using the security procedure and sends AttachAccept with to the UE:

TAI (MCC/MNC/TAC): 244/083/ 0001

GUTI: "24408300010266436587"

d) After receipt of the AttachComplete during registration from the UE, the NB-SS sends RRCConnectionRelease-NB.

e) The UE is soft powered down.

7.3.8.5 Acceptance criteria

1.) After step a) the UE shall send a RRCConnectionRequest-NB on the NB-IoT-cell related to the BCCH transmitting MCC/MNC 244/083 to the NB-SS.

2) After step b) the terminal shall send AttachRequest to the NB-SS.

3) After step c) the terminal shall respond with AttachComplete during registration.

4) After step e) the USIM shall contain the following values:

EFEPSLOCI (EPS Information)

Logically: GUTI: 24408300010266436587

Last visited registered TAI: 244/083/0001

EPS update status: updated

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

B9

B10

B11

Hex

0B

F6

42

34

80

00

01

02

66

43

65

B12

B13

B14

B15

B16

B17

B18

87

42

34

80

00

01

00

7.3.9 UE recognising the priority order of the Operator controlled PLMN selector list using the ACT preference – E-UTRAN in WB-S1 mode/GSM

7.3.9.1 Definition and applicability

The Operator controlled PLMN selector list gives in priority order the preferred OPLMNs on which the UE shall register if no network of the User controlled PLMN selector list is available. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFOPLMNwACT. Update and deletion of OPLMNs shall not be possible by the subscriber by the use of the PIN.

7.3.9.2 Conformance requirement

When registering onto a VPLMN the UE shall take into account the priority of OPLMNs in the preferred list on the USIM.

– TS 22.011 [6], clause 3.2.2;

– TS 31.102 [4], clause 4.2.53, 4.2.5 and 5.1.1.2.

7.3.9.3 Test purpose

To verify that the OPLMN with the higher priority (defined by its position in EFOPLMNwACT) takes precedence over the OPLMN with the lower priority when the UE performs a network selection. Hereby the new coding for RAT
E-UTRAN in WB-S1 mode has to be handled correctly by the UE.

7.3.9.4 Method of test

7.3.9.4.1 Initial conditions

For this test both a GSM SS and an E-UTRAN E-USS is needed.

The GSM SS transmits on BCCH, with the following network parameters:

– Attach/detach: disabled.

– LAI (MCC/MNC/LAC): 244/083/0001.

– Access control: unrestricted.

The E-USS transmits on the BCCH, with the following network parameters:

– TAI (MCC/MNC/TAC): 244/083/0001.

– Access control: unrestricted.

The default E-UTRAN UICC is used with the following exception:

EFOPLMNwACT (Operator Controlled PLMN Selector with Access Technology)

Logically: 1st PLMN: 254 001 (MCC MNC)

1st ACT: E-UTRAN

2nd PLMN: 254 001

2nd ACT: GSM

3rd PLMN: 244 083

3rd ACT: E-UTRAN in WB-S1 mode

4th PLMN: 244 083

4th ACT: GSM

5th PLMN: 254 004

5th ACT: UTRAN

6th PLMN: 254 005

6th ACT: UTRAN

7th PLMN: 254 006

7th ACT: UTRAN

8th PLMN: 254 007

8th ACT: UTRAN

Coding:

B01

B02

B03

B04

B05

B06

B07

B08

B09

B10

Hex

52

14

00

40

00

52

14

00

00

80

B11

B12

B13

B14

B15

B16

B17

B18

B19

B20

42

34

80

60

00

42

34

80

00

80

B21

B22

B23

B24

B25

B26

B27

B28

B29

B30

52

44

00

80

00

52

54

00

80

00

B31

B32

B33

B34

B35

B36

B37

B38

B39

B40

52

64

00

80

00

52

74

00

80

00

The UICC is installed into the Terminal and the UE is set to automatic PLMN selection mode.

7.3.9.4.2 Procedure

a) The UE is powered on.

b) After receipt of an RRCConnectionRequest from the UE on the E-UTRAN-cell related to the BCCH transmitting MCC/MNC 244/083, the E-USS sends RRCConnectionSetup to the UE, followed by RRCConnectionSetupComplete sent by the UE to the E-USS.

c) During registration and after receipt of a AttachRequest from the UE, the E-USS initiates authentication, starts integrity by using the security procedure and sends AttachAccept with to the UE:

TAI (MCC/MNC/TAC): 244/083/ 0001

GUTI: "24408300010266436587"

d) After receipt of the AttachComplete during registration from the UE, the E-USS sends RRCConnectionRelease.

e) The UE is soft powered down.

7.3.9.5 Acceptance criteria

1.) After step a) the UE shall send a RRCConnectionRequest on the E-UTRAN-cell related to the BCCH transmitting MCC/MNC 244/083 to the E-USS.

2) After step b) the terminal shall send AttachRequest to the E-USS.

3) After step c) the terminal shall respond with AttachComplete during registration.

4) After step e) the USIM shall contain the following values:

EFEPSLOCI (EPS Information)

Logically: GUTI: 24408300010266436587

Last visited registered TAI: 244/083/0001

EPS update status: updated

Coding:

B1

B2

B3

B4

B5

B6

B7

B8

B9

B10

B11

Hex

0B

F6

42

34

80

00

01

02

66

43

65

B12

B13

B14

B15

B16

B17

B18

87

42

34

80

00

01

00