7.2 User controlled PLMN selector handling
31.1213GPPRelease 16TSUICC-terminal interfaceUniversal Subscriber Identity Module (USIM) application test specification
7.2.1 UE updating the User controlled PLMN selector list
7.2.1.1 Definition and applicability
The User controlled PLMN selector list gives in priority order the preferred UPLMNs on which the UE shall register. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFPLMNwACT. Update and deletion of PLMNs may be performed by the subscriber.
7.2.1.2 Conformance requirement
The UE shall correctly replace the selected UPLMN in the User controlled PLMN selector list.
– TS 31.102 [4], clause 5.3.6.
7.2.1.3 Test purpose
To verify that the UE correctly updates the EFPLMNwACT.
7.2.1.4 Method of test
7.2.1.4.1 Initial conditions
No USS/SS is required for this test.
The default UICC is used.
The UICC is installed into the Terminal and the UE is powered on.
7.2.1.4.2 Procedure
a) The user shall initiate an MMI dependent procedure to change the second UPLMN in the User controlled PLMN selector list to MCC/MNC of 567/02, the ACT identifier shall set to UTRAN only.
b) The UE is soft powered down.
7.2.1.5 Acceptance criteria
After step b) the USIM shall contain the following values:
EFPLMNwACT (UPLMN Selector)
Logically: 1st PLMN: 244 081 (MCC MNC)
1st ACT: UTRAN
2nd PLMN: 567 02
2nd ACT UTRAN
3rd PLMN: 244 082
3rd ACT UTRAN
4th PLMN: 244 082
4th ACT GSM
5th PLMN: 244 003
5th ACT UTRAN
6th PLMN: 244 004
6th ACT UTRAN
7th PLMN: 244 005
7th ACT UTRAN
8th PLMN: 244 006
8th ACT UTRAN
9th PLMN: 244 007
9th ACT UTRAN
10th PLMN: 244 008
10th ACT UTRAN
11th PLMN: 244 009
11th ACT UTRAN
12th PLMN: 244 010
12th ACT UTRAN
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
B12 |
B13 |
B14 |
B15 |
|
Hex |
42 |
14 |
80 |
80 |
00 |
65 |
F7 |
20 |
80 |
00 |
42 |
24 |
80 |
80 |
00 |
|
B16 |
B17 |
B18 |
B19 |
B20 |
B21 |
B22 |
B23 |
B24 |
B25 |
B26 |
B27 |
B28 |
B29 |
B30 |
|
|
42 |
24 |
80 |
00 |
80 |
42 |
34 |
00 |
80 |
00 |
42 |
44 |
00 |
80 |
00 |
|
|
B31 |
B32 |
B33 |
B34 |
B35 |
B36 |
B37 |
B38 |
B39 |
B40 |
B41 |
B42 |
B43 |
B44 |
B45 |
|
|
42 |
54 |
00 |
80 |
00 |
42 |
64 |
00 |
80 |
00 |
42 |
74 |
00 |
80 |
00 |
|
|
B46 |
B47 |
B48 |
B49 |
B50 |
B51 |
B52 |
B53 |
B54 |
B55 |
B56 |
B57 |
B58 |
B59 |
B60 |
|
|
42 |
84 |
00 |
80 |
00 |
42 |
94 |
00 |
80 |
00 |
42 |
04 |
10 |
80 |
00 |
7.2.2 UE recognising the priority order of the User controlled PLMN selector list with the same access technology.
7.2.2.1 Definition and applicability
The User controlled PLMN selector list gives in priority order the preferred UPLMNs on which the UE shall register. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFPLMNwACT. Update and deletion of UPLMNs may be performed by the subscriber by the use of the PIN.
The registration attempts initiated by the terminal accessing UTRAN depends on terminal’s capabilities and can be one of the following:
I. registration procedures for Ues supporting CS or
II. registration procedures for Ues supporting PS or
III. registration procedures for Ues supporting CS/PS
7.2.2.2 Conformance requirement
When registering onto a VPLMN the UE shall take into account the priority order of the UPLMNs in the preferred list on the USIM.
– TS 22.011 [6], clause 3.2.2.
7.2.2.3 Test purpose
To verify that the UPLMN with the higher priority (defined by its position in EFPLMNwACT) takes precedence over the UPLMN with the lower priority when the UE performs a network selection.
7.2.2.4 Method of test
7.2.2.4.1 Initial conditions
The USS (in case of a Terminal accessing UTRAN)/SS (in case of a Terminal accessing a GERAN) transmits on two BCCHs, with the following network parameters:
– Attach/detach: disabled.
– LAI (MCC/MNC/LAC): 244/033/0001.
– RAI (MCC/MNC/LAC/RAC): 244/033/0001/05 (only for UTRAN cell).
– Access control: unrestricted.
– Attach/detach: disabled.
– LAI (MCC/MNC/LAC): 244/034/0001.
– RAI (MCC/MNC/LAC/RAC): 244/034/0001/05 (only for UTRAN cell).
– Access control: unrestricted.
NOTE: In case of a GERAN no packet system information is transmitted
The default UICC is used with the following exception:
EFPLMNwACT (UPLMN Selector with Access Technology)
Logically: 1st PLMN: 244 081 (MCC MNC)
1st ACT: UTRAN
2nd PLMN: 244 081
2nd ACT GSM
3rd PLMN: 244 082
3rd ACT UTRAN
3rd PLMN: 244 082
3rd AIGSI……..
……..
8th PLMN: 244 034
8th ACT GSM
9th PLMN: 244 033
9th ACT GSM
10th PLMN: 244 008
10th ACT UTRAN
11th PLMN: 244 034
11th ACT UTRAN
12th PLMN: 244 033
12th ACT UTRAN
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
B12 |
B13 |
B14 |
B15 |
|
Hex |
42 |
14 |
80 |
80 |
00 |
42 |
14 |
80 |
00 |
80 |
42 |
24 |
80 |
80 |
00 |
|
B16 |
B17 |
B18 |
B19 |
B20 |
….. |
….. |
….. |
….. |
|||||||
|
42 |
24 |
80 |
00 |
80 |
….. |
….. |
….. |
….. |
|||||||
|
….. |
….. |
B36 |
B37 |
B38 |
B39 |
B40 |
B41 |
B42 |
B43 |
B44 |
B45 |
||||
|
….. |
….. |
42 |
44 |
30 |
00 |
80 |
42 |
34 |
30 |
00 |
80 |
||||
|
B46 |
B47 |
B48 |
B49 |
B50 |
B51 |
B52 |
B53 |
B54 |
B55 |
B56 |
B57 |
B58 |
B59 |
B60 |
|
|
42 |
84 |
00 |
80 |
00 |
42 |
44 |
30 |
80 |
00 |
42 |
34 |
30 |
80 |
00 |
The UICC is installed into the Terminal and the UE is set to automatic PLMN selection mode.
In case of a Terminal accessing UTRAN "Expected Sequence A" and in case of a Terminal accessing a GERAN "Expected Sequence B" shall be performed.
7.2.2.4.2 Procedure
Expected Sequence A:
a) The UE is powered on.
b) After receipt on the cell related to the BCCH transmitting MCC/MNC 244/034 of a RRC CONNECTION REQUEST from the UE, the USS sends RRC CONNECTION SETUP to the UE, followed by RRC CONNECTION SETUP COMPLETE sent by the UE to the USS.
c) Depending on which domain the UE is going to be registered on, one of the following sequences will be passed through:
I. During registration on CS and after receipt of a LOCATION UPDATING REQUEST from the UE, the USS initiates authentication, starts integrity by using the security procedure and sends LOCATION UPDATING ACCEPT to the UE with the following values:
LAI (MCC/MNC/LAC): 244/034/0001
TMSI: "34567890"
II. During registration on PS and after receipt of a ATTACH REQUEST from the UE, the USS initiates authentication, starts integrity by using the security procedure and sends ATTACH ACCEPT to the UE with the following values:
RAI (MCC/MNC/LAC/RAC) 244/034/0001/05
P-TMSI "34567890"
P-TMSI signature value "AB1234"
III. During registration on CS/PS and after receipt of a LOCATION UPDATING REQUEST and/or ATTACH REQUEST from the UE, the USS initiates authentication, starts integrity by using the security procedure and sends LOCATION UPDATING ACCEPT and/or ATTACH ACCEPT to the UE with some of the following values:
LAI (MCC/MNC/LAC): 244/034/0001
TMSI: "34567890"
RAI (MCC/MNC/LAC/RAC) 244/034/0001/05
P-TMSI "34567890"
P-TMSI signature value "AB1234"
d) After passing through the authentication procedure and after receipt of
I. TMSI REALLOCATION COMPLETE during registration on CS from the UE, the USS sends RRC CONNECTION RELEASE to the UE, followed by RRC CONNECTION RELEASE COMPLETE sent by the UE to the USS or
II. ATTACH COMPLETE during registration on PS from the UE, the USS sends RRC CONNECTION RELEASE, followed by RRC CONNECTION RELEASE COMPLETE sent by the UE to the USS or.
III. TMSI REALLOCATION COMPLETE and/or ATTACH COMPLETE during registration on CS/PS from the UE, the USS sends RRC CONNECTION RELEASE, followed by RRC CONNECTION RELEASE COMPLETE sent by the UE to the USS.
e) The UE is soft powered down.
Expected Sequence B:
a) The UE is powered on.
b) After receipt of a CHANNEL REQUEST from the UE, the SS sends IMMEDIATE ASSIGNMENT to the UE.
c) After receipt of a LOCATION UPDATING REQUEST from the UE, the SS sends LOCATION UPDATING ACCEPT with:
LAI (MCC/MNC/LAC): 244/034/0001
TMSI: "34567890"
to the UE
d) After receipt of a TMSI REALLOCATION COMPLETE from the UE, the SS sends CHANNEL RELEASE to the UE.
e) The UE is soft powered down.
7.2.2.5 Acceptance criteria
1) After step a) the UE accessing a GERAN shall send CHANNEL REQUEST on the cell related to the BCCH transmitting MCC/MNC 244/034 to the SS and the UE accessing UTRAN shall send an RRC CONNECTION REQUEST on the cell related to the BCCH transmitting MCC/MNC 244/034 to the USS.
2) After step b) the UE accessing a GERAN shall send LOCATION UPDATING REQUEST to the SS and the UE accessing UTRAN shall send
I. LOCATION UPDATING REQUEST to the USS during registration on CS or
II. ATTACH REQUEST to the USS during registration on PS or
III. LOCATION UPDATING REQUEST and/or ATTACH REQUEST to the USS during registration on CS/PS.
3) After step c) the UE accessing a GERAN shall respond with TMSI REALLOCATION COMPLETE and the UE accessing UTRAN shall respond with
I. TMSI REALLOCATION COMPLETE to the USS during registration on CS or
II. ATTACH COMPLETE during registration on PS or
III. TMSI REALLOCATION COMPLETE and/or ATTACH COMPLETE to the USS during registration on CS/PS.
4) After step e) the USIM shall contain the following values:
For UEs accessing GERAN and UEs accessing UTRAN and supporting (CS and PS) or (CS only):
EFLOCI (Location Information)
Logically: LAI-MCC: 244
LAI-MNC: 034
TMSI: "34567890"
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
|
Hex |
34 |
56 |
78 |
90 |
42 |
44 |
30 |
xx |
xx |
xx |
00 |
For UEs accessing UTRAN and supporting (CS and PS) or (PS only):
EFPSLOCI (Location Information)
Logically: RAI-MCC: 244
RAI-MNC: 034
P-TMSI: "34567890"
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
|
Hex |
34 |
56 |
78 |
90 |
xx |
xx |
xx |
42 |
44 |
30 |
xx |
|
Coding: |
B12 |
B13 |
B14 |
||||||||
|
Hex |
xx |
xx |
00 |
7.2.3 UE recognising the priority order of the User controlled PLMN selector list using an ACT preference.
7.2.3.1 Definition and applicability
The User controlled PLMN selector list gives in priority order the preferred PLMNs of the User on which the UE shall register. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFPLMNwACT. Update and deletion of User controlled PLMNs may be performed by the subscriber by the use of the PIN.
7.2.3.2 Conformance requirement
When registering onto a VPLMN the UE shall take into account the priority of the ACT identifier in the preferred list on the USIM.
– TS 22.011 [6], clause 3.2.2;
– TS 31.102 [4], clauses 4.2.5 and 5.1.2.
7.2.3.3 Test purpose
To verify that the ACT with the higher priority (defined by its position in EFPLMNwACT) takes precedence over the UPLMN with the lower priority when the UE performs a network selection.
7.2.3.4 Method of test
7.2.3.4.1 Initial conditions
For this test both a GSM SS and an UTRAN USS is needed.
The GSM SS transmits on BCCH, with the following network parameters:
– Attach/detach: disabled.
– LAI (MCC/MNC/LAC): 244/081/0001.
– RAI (MCC/MNC/LAC/RAC): 244/081/0001/05.
– Access control: unrestricted.
The UMTS USS transmits on BCCH, with the following network parameters:
– Attach/detach: disabled.
– RAI (MCC/MNC/LAC/RAC): 244/082/0001/05.
– Access control: unrestricted.
The default UICC is used.
The UICC is installed into the Terminal and the UE is set to automatic PLMN selection mode.
7.2.3.4.2 Procedure
a) The UE is powered on.
b) After receipt of a CHANNEL REQUEST from the UE on the GSM-cell related to the BCCH transmitting MCC/MNC 244/081, the SS sends IMMEDIATE ASSIGNMENT to the UE.
c) After receipt of a LOCATION UPDATING REQUEST and/or an ATTACH REQUEST from the UE, the SS sends a LOCATION UPDATING ACCEPT with:
LAI (MCC/MNC/LAC): 244/081/0001
TMSI: "34567890"
and/or an ATTACH ACCEPT with:
RAI (MCC/MNC/LAC/RAC) 244/081/0001/05
P-TMSI "34567890"
P-TMSI signature value "AB1234"
to the UE.
d) After receipt of a TMSI REALLOCATION COMPLETE and/or an ATTACH COMPLETE from the UE, the SS sends CHANNEL RELEASE to the UE.
e) The UE is soft powered down.
7.2.3.5 Acceptance criteria
1.) After step a) the UE shall send a CHANNEL REQUEST on the GSM-cell related to the BCCH transmitting MCC/MNC 244/081 to the SS.
2) After step b) the UE shall send a LOCATION UPDATING REQUEST and/or an ATTACH REQUEST to the SS.
3) After step c) the UE shall respond with a TMSI REALLOCATION COMPLETE and/or an ATTACH COMPLETE.
4) After step e) the USIM shall contain the following values:
For UEs supporting (CS and PS) or (CS only):
EFLOCI (Location Information)
Logically: LAI-MCC: 244
LAI-MNC: 081
TMSI: "34567890"
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
|
Hex |
34 |
56 |
78 |
90 |
42 |
14 |
80 |
xx |
xx |
xx |
00 |
For UEs supporting (CS and PS) or (PS only):
EFPSLOCI (Location Information)
Logically: RAI-MCC: 244
RAI-MNC: 081
P-TMSI: "34567890"
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
|
Hex |
34 |
56 |
78 |
90 |
xx |
xx |
xx |
42 |
14 |
80 |
xx |
|
Coding: |
B12 |
B13 |
B14 |
||||||||
|
Hex |
xx |
xx |
00 |
7.2.4 Void
7.2.5 UE updating the User controlled PLMN selector list for E-UTRAN
7.2.5.1 Definition and applicability
The User controlled PLMN selector list gives in priority order the preferred UPLMNs on which the UE shall register. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFPLMNwACT. Update and deletion of PLMNs may be performed by the subscriber.
7.2.5.2 Conformance requirement
The UE shall correctly replace the selected UPLMN in the User controlled PLMN selector list.
– TS 31.102 [4], clause 5.3.6 and 4.2.5.
7.2.5.3 Test purpose
To verify that the UE correctly updates the EFPLMNwACT.
7.2.5.4 Method of test
7.2.5.4.1 Initial conditions
No USS/SS is required for this test.
The default E-UTRAN UICC is used.
The UICC is installed into the Terminal and the UE is powered on.
7.2.5.4.2 Procedure
a) The user shall initiate an MMI dependent procedure to change the second UPLMN in the User controlled PLMN selector list to MCC/MNC of 567/04, the ACT identifier shall set to E-UTRAN only.
b) The UE is soft powered down.
7.2.5.5 Acceptance criteria
After step b) the USIM shall contain the following values:
EFPLMNwACT (UPLMN Selector)
Logically: 1st PLMN: 244 081 (MCC MNC)
1st ACT: E-UTRAN
2nd PLMN: 567 04
2nd ACT E-UTRAN
3rd PLMN: 244 083
3rd ACT: E-UTRAN
4th PLMN: 244 082
4th ACT: GSM
5th PLMN: 244 003
5th ACT: E-UTRAN
6th PLMN: 244 004
6th ACT: UTRAN
7th PLMN: 244 005
7th ACT: UTRAN
8th PLMN: 244 081
8th ACT: UTRAN
9th PLMN: 244 007
9th ACT: UTRAN
10th PLMN: 244 008
10th ACT: E-UTRAN
11th PLMN: 244 009
11th ACT: UTRAN
12th PLMN: 244 010
12th ACT: E-UTRAN
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
B12 |
B13 |
B14 |
B15 |
|
Hex |
42 |
14 |
80 |
40 |
00 |
65 |
F7 |
40 |
40 |
00 |
42 |
34 |
80 |
40 |
00 |
|
B16 |
B17 |
B18 |
B19 |
B20 |
B21 |
B22 |
B23 |
B24 |
B25 |
B26 |
B27 |
B28 |
B29 |
B30 |
|
|
42 |
24 |
80 |
00 |
80 |
42 |
34 |
00 |
40 |
00 |
42 |
44 |
00 |
80 |
00 |
|
|
B31 |
B32 |
B33 |
B34 |
B35 |
B36 |
B37 |
B38 |
B39 |
B40 |
B41 |
B42 |
B43 |
B44 |
B45 |
|
|
42 |
54 |
00 |
80 |
00 |
42 |
14 |
80 |
80 |
00 |
42 |
74 |
00 |
80 |
00 |
|
|
B46 |
B47 |
B48 |
B49 |
B50 |
B51 |
B52 |
B53 |
B54 |
B55 |
B56 |
B57 |
B58 |
B59 |
B60 |
|
|
42 |
84 |
00 |
40 |
00 |
42 |
94 |
00 |
80 |
00 |
42 |
04 |
10 |
40 |
00 |
7.2.6 UE recognising the priority order of the User controlled PLMN selector list using an ACT preference- UTRAN/E-UTRAN
7.2.6.1 Definition and applicability
The User controlled PLMN selector list gives in priority order the preferred PLMNs of the User on which the UE shall register. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFPLMNwACT. Update and deletion of User controlled PLMNs may be performed by the subscriber by the use of the PIN.
7.2.6.2 Conformance requirement
When registering onto a VPLMN the UE shall take into account the priority of the ACT identifier in the preferred list on the USIM.
– TS 22.011 [6], clause 3.2.2;
– TS 31.102 [4], clauses 4.2.5 and 5.1.1.2.
7.2.6.3 Test purpose
To verify that the ACT with the higher priority (defined by its position in EFPLMNwACT) takes precedence over the UPLMN with the lower priority when the UE performs a network selection. Hereby the new coding for RAT
E-UTRAN has to be handled correctly by the UE.
7.2.6.4 Method of test
7.2.6.4.1 Initial conditions
For this test both a UTRAN USS and an E-UTRAN E-USS is needed.
The USS transmits on BCCH, with the following network parameters:
– Attach/detach: disabled.
– LAI (MCC/MNC/LAC): 244/004/0001.
– Access control: unrestricted.
The E-USS transmits on the BCCH, with the following network parameters:
– TAI (MCC/MNC/TAC): 244/003/0001.
– Access control: unrestricted.
The default E-UTRAN UICC is used.
The UICC is installed into the Terminal and the UE is set to automatic PLMN selection mode.
7.2.6.4.2 Procedure
a) The UE is powered on.
b) After receipt of an RRCConnectionRequest from the UE on the E-UTRAN-cell related to the BCCH transmitting MCC/MNC 244/003, the E-USS sends RRCConnectionSetup to the UE, followed by RRCConnectionSetupComplete sent by the UE to the E-USS.
c) During registration and after receipt of a AttachRequest from the UE, the E-USS initiates authentication, starts integrity by using the security procedure and sends AttachAccept with to the UE:
TAI (MCC/MNC/TAC): 244/003/ 0001
GUTI: "24400300010266436587"
d) After receipt of the AttachComplete during registration from the UE, the E-USS sends RRCConnectionRelease.
e) The UE is soft powered down.
7.2.6.5 Acceptance criteria
1.) After step a) the UE shall send a RRCConnectionRequest on the E-UTRAN-cell related to the BCCH transmitting MCC/MNC 244/003 to the E-USS.
2) After step b) the terminal shall send AttachRequest to the E-USS.
3) After step c) the terminal shall respond with AttachComplete during registration.
4) After step e) the USIM shall contain the following values:
EFEPSLOCI (EPS Information)
Logically: GUTI: 24400300010266436587
Last visited registered TAI: 244/003/0001
EPS update status: updated
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
|
Hex |
0B |
F6 |
42 |
34 |
00 |
00 |
01 |
02 |
66 |
43 |
65 |
|
B12 |
B13 |
B14 |
B15 |
B16 |
B17 |
B18 |
|||||
|
87 |
42 |
34 |
00 |
00 |
01 |
00 |
7.2.7 UE recognising the priority order of the User controlled PLMN selector list using an ACT preference- GSM/E-UTRAN
7.2.7.1 Definition and applicability
The User controlled PLMN selector list gives in priority order the preferred PLMNs of the User on which the UE shall register. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFPLMNwACT. Update and deletion of User controlled PLMNs may be performed by the subscriber by the use of the PIN.
7.2.7.2 Conformance requirement
When registering onto a VPLMN the UE shall take into account the priority of the ACT identifier in the preferred list on the USIM.
– TS 22.011 [6], clause 3.2.2;
– TS 31.102 [4], clauses 4.2.5 and 5.1.1.2.
7.2.7.3 Test purpose
To verify that the ACT with the higher priority (defined by its position in EFPLMNwACT) takes precedence over the UPLMN with the lower priority when the UE performs a network selection. Hereby the new coding for RAT
E-UTRAN has to be handled correctly by the UE.
7.2.7.4 Method of test
7.2.7.4.1 Initial conditions
For this test both a GSM SS and an E-UTRAN E-USS is needed.
The GSM SS transmits on BCCH, with the following network parameters:
– Attach/detach: disabled.
– LAI (MCC/MNC/LAC): 244/082/0001.
– Access control: unrestricted.
The E-USS transmits on the BCCH, with the following network parameters:
– TAI (MCC/MNC/TAC): 244/083/0001.
– Access control: unrestricted.
The default E-UTRAN UICC is used.
The UICC is installed into the Terminal and the UE is set to automatic PLMN selection mode.
7.2.7.4.2 Procedure
a) The UE is powered on.
b) After receipt of an RRCConnectionRequest from the UE on the E-UTRAN-cell related to the BCCH transmitting MCC/MNC 244/083, the E-USS sends RRCConnectionSetup to the UE, followed by RRCConnectionSetupComplete sent by the UE to the E-USS.
c) During registration and after receipt of a AttachRequest from the UE, the E-USS initiates authentication, starts integrity by using the security procedure and sends AttachAccept with to the UE:
TAI (MCC/MNC/TAC): 244/083/ 0001
GUTI: "24408300010266436587"
d) After receipt of the AttachComplete during registration from the UE, the E-USS sends RRCConnectionRelease.
e) The UE is soft powered down.
7.2.7.5 Acceptance criteria
1.) After step a) the UE shall send a RRCConnectionRequest on the E-UTRAN-cell related to the BCCH transmitting MCC/MNC 244/083 to the e-USS.
2) After step b) the terminal shall send AttachRequest to the E-USS.
3) After step c) the terminal shall respond with AttachComplete during registration.
4) After step e) the USIM shall contain the following values:
EFEPSLOCI (EPS Information)
Logically: GUTI: 24408300010266436587
Last visited registered TAI: 244/083/0001
EPS update status: updated
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
|
Hex |
0B |
F6 |
42 |
34 |
80 |
00 |
01 |
02 |
66 |
43 |
65 |
|
B12 |
B13 |
B14 |
B15 |
B16 |
B17 |
B18 |
|||||
|
87 |
42 |
34 |
80 |
00 |
01 |
00 |
7.2.8 UE recognising the priority order of the User controlled PLMN selector list with the same access technology – E-UTRAN in NB-S1 mode
7.2.8.1 Definition and applicability
The User controlled PLMN selector list gives in priority order the preferred PLMNs of the User on which the UE shall register. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFPLMNwACT. Update and deletion of User controlled PLMNs may be performed by the subscriber by the use of the PIN.
7.2.8.2 Conformance requirement
When registering onto a VPLMN the UE shall take into account the priority of the ACT identifier in the preferred list on the USIM.
– TS 22.011 [6], clause 3.2.2;
– TS 31.102 [4], clauses 4.2.5 and 5.1.1.2.
7.2.8.3 Test purpose
To verify that the ACT with the higher priority (defined by its position in EFPLMNwACT) takes precedence over the UPLMN with the lower priority when the UE performs a network selection. Hereby the new coding for
E-UTRAN in NB-S1 mode has to be handled correctly by the UE.
7.2.8.4 Method of test
7.2.8.4.1 Initial conditions
For this test 2 NB-IoT-cells are needed.
The NB-SS transmits on BCCH, with the following network parameters:
– TAI (MCC/MNC/TAC): 244/081/0001.
– Access control: unrestricted.
The NB-SS transmits on the BCCH, with the following network parameters:
– TAI (MCC/MNC/TAC): 244/083/0001.
– Access control: unrestricted.
The default E-UTRAN UICC is used, with the following exception:
EFPLMNwACT (User Controlled PLMN Selector with Access Technology)
Logically: 1st PLMN: 244 083 (MCC MNC)
1st ACT: E-UTRAN in NB-S1mode
2nd PLMN: 244 081
2nd ACT: E-UTRAN in NB-S1 mode
3rd PLMN: 244 083
3rd ACT: E-UTRAN
4th PLMN: 244 082
4th ACT: GSM
5th PLMN: 244 003
5th ACT: E-UTRAN
6th PLMN: 244 004
6th ACT: UTRAN
7th PLMN: 244 005
7th ACT: UTRAN
8th PLMN: 244 081
8th ACT: UTRAN
9th PLMN: 244 007
9th ACT: UTRAN
10th PLMN: 244 008
10th ACT: E-UTRAN
11th PLMN: 244 009
11th ACT: UTRAN
12th PLMN: 244 010
12th ACT: E-UTRAN
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
B12 |
B13 |
B14 |
B15 |
|
Hex |
42 |
34 |
80 |
50 |
00 |
42 |
14 |
80 |
50 |
00 |
42 |
34 |
80 |
40 |
00 |
|
B16 |
B17 |
B18 |
B19 |
B20 |
B21 |
B22 |
B23 |
B24 |
B25 |
B26 |
B27 |
B28 |
B29 |
B30 |
|
|
42 |
24 |
80 |
00 |
80 |
42 |
34 |
00 |
40 |
00 |
42 |
44 |
00 |
80 |
00 |
|
|
B31 |
B32 |
B33 |
B34 |
B35 |
B36 |
B37 |
B38 |
B39 |
B40 |
B41 |
B42 |
B43 |
B44 |
B45 |
|
|
42 |
54 |
00 |
80 |
00 |
42 |
14 |
80 |
80 |
00 |
42 |
74 |
00 |
80 |
00 |
|
|
B46 |
B47 |
B48 |
B49 |
B50 |
B51 |
B52 |
B53 |
B54 |
B55 |
B56 |
B57 |
B58 |
B59 |
B60 |
|
|
42 |
84 |
00 |
40 |
00 |
42 |
94 |
00 |
80 |
00 |
42 |
04 |
10 |
40 |
00 |
The UICC is installed into the Terminal and the UE is set to automatic PLMN selection mode.
7.2.8.2 Procedure
a) The UE is powered on.
b) After receipt of an RRCConnectionRequest-NB from the UE on the NB-IoT-cell related to the BCCH transmitting MCC/MNC 244/083, the NB-SS sends RRCConnectionSetup-NB to the UE, followed by RRCConnectionSetupComplete-NB sent by the UE to the NB-SS.
c) During registration and after receipt of a AttachRequest from the UE, the NB-SS initiates authentication, starts integrity by using the security procedure and sends AttachAccept with to the UE:
TAI (MCC/MNC/TAC): 244/083/ 0001
GUTI: "24408300010266436587"
d) After receipt of the AttachComplete during registration from the UE, the NB-SS sends RRCConnectionRelease-NB.
e) The UE is powered down.
7.2.8.5 Acceptance criteria
1) After step a) the UE shall send a RRCConnectionRequest-NB on the NB-IoT -cell related to the BCCH transmitting MCC/MNC 244/083 to the NB-SS.
2) After step b) the terminal shall send AttachRequest to the NB-SS.
3) After step c) the terminal shall respond with AttachComplete during registration.
4) After step e) the USIM shall contain the following values:
EFEPSLOCI (EPS Information)
Logically: GUTI: 24408300010266436587
Last visited registered TAI: 244/083/0001
EPS update status: updated
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
|
Hex |
0B |
F6 |
42 |
34 |
80 |
00 |
01 |
02 |
66 |
43 |
65 |
|
B12 |
B13 |
B14 |
B15 |
B16 |
B17 |
B18 |
|||||
|
87 |
42 |
34 |
80 |
00 |
01 |
00 |
7.2.9 UE recognising the priority order of the User controlled PLMN selector list using the ACT preference – E-UTRAN in WB-S1/E-UTRAN in NB-S1
7.2.9.1 Definition and applicability
The User controlled PLMN selector list gives in priority order the preferred PLMNs of the User on which the UE shall register. The Radio Access Technology identifier defines the Radio network in which the UE shall register. The list is stored on the USIM in the EFPLMNwACT. Update and deletion of User controlled PLMNs may be performed by the subscriber by the use of the PIN.
7.2.9.2 Conformance requirement
When registering onto a VPLMN the UE shall take into account the priority of the ACT identifier in the preferred list on the USIM.
– TS 22.011 [6], clause 3.2.2;
– TS 31.102 [4], clauses 4.2.5 and 5.1.1.2.
7.2.9.3 Test purpose
To verify that the ACT with the higher priority (defined by its position in EFPLMNwACT) takes precedence over the UPLMN with the lower priority when the UE performs a network selection. Hereby the new coding for RAT
E-UTRAN in WB-S1 mode and E-UTRAN in NB-S1 mode has to be handled correctly by the UE.
7.2.9.4 Method of test
7.2.9.4.1 Initial conditions
For this test both an E-USS and NB-SS are needed.
The E-USS transmits on BCCH, with the following network parameters:
– Attach/detach: disabled.
– TAI (MCC/MNC/LAC): 244/083/0001.
– Access control: unrestricted.
The NB-SS transmits on the BCCH, with the following network parameters:
– TAI (MCC/MNC/TAC): 244/083/0001.
– Access control: unrestricted.
The default E-UTRAN UICC is used with the following exception:
EFPLMNwACT (User Controlled PLMN Selector with Access Technology)
Logically: 1st PLMN: 244 081 (MCC MNC)
1st ACT: E-UTRAN
2nd PLMN: 244 081
2nd ACT: GSM
3rd PLMN: 244 083
3rd ACT: E-UTRAN in NB-S1 mode
4th PLMN: 244 083
4th ACT: E-UTRAN in WB-S1 mode
5th PLMN: 244 003
5th ACT: E-UTRAN
6th PLMN: 244 004
6th ACT: UTRAN
7th PLMN: 244 005
7th ACT: UTRAN
8th PLMN: 244 081
8th ACT: UTRAN
9th PLMN: 244 007
9th ACT: UTRAN
10th PLMN: 244 008
10th ACT: E-UTRAN
11th PLMN: 244 009
11th ACT: UTRAN
12th PLMN: 244 010
12th ACT: E-UTRAN
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
B12 |
B13 |
B14 |
B15 |
|
Hex |
42 |
14 |
80 |
40 |
00 |
42 |
14 |
80 |
00 |
80 |
42 |
34 |
80 |
50 |
00 |
|
B16 |
B17 |
B18 |
B19 |
B20 |
B21 |
B22 |
B23 |
B24 |
B25 |
B26 |
B27 |
B28 |
B29 |
B30 |
|
|
42 |
34 |
80 |
60 |
00 |
42 |
34 |
00 |
40 |
00 |
42 |
44 |
00 |
80 |
00 |
|
|
B31 |
B32 |
B33 |
B34 |
B35 |
B36 |
B37 |
B38 |
B39 |
B40 |
B41 |
B42 |
B43 |
B44 |
B45 |
|
|
42 |
54 |
00 |
80 |
00 |
42 |
14 |
80 |
80 |
00 |
42 |
74 |
00 |
80 |
00 |
|
|
B46 |
B47 |
B48 |
B49 |
B50 |
B51 |
B52 |
B53 |
B54 |
B55 |
B56 |
B57 |
B58 |
B59 |
B60 |
|
|
42 |
84 |
00 |
40 |
00 |
42 |
94 |
00 |
80 |
00 |
42 |
04 |
10 |
40 |
00 |
The UICC is installed into the Terminal and the UE is set to automatic PLMN selection mode.
7.2.9.4.2 Procedure
a) The UE is powered on.
b) After receipt of an RRCConnectionRequest-NB from the UE on the NB-IoT-cell related to the BCCH transmitting MCC/MNC 244/083, the NB-SS sends RRCConnectionSetup-NB to the UE, followed by RRCConnectionSetupComplete-NB sent by the UE to the NB-SS.
c) During registration and after receipt of a AttachRequest from the UE, the NB-SS initiates authentication, starts integrity by using the security procedure and sends AttachAccept with to the UE:
TAI (MCC/MNC/TAC): 244/083/ 0001
GUTI: "24408300010266436587"
d) After receipt of the AttachComplete during registration from the UE, the NB-SS sends RRCConnectionRelease-NB.
e) The UE is soft powered down.
7.2.9.5 Acceptance criteria
1) After step a) the UE shall send a RRCConnectionRequest-NB on the NB-IoT-cell related to the BCCH transmitting MCC/MNC 244/083 to the NB-SS.
2) After step b) the terminal shall send AttachRequest to the NB-SS.
3) After step c) the terminal shall respond with AttachComplete during registration.
4) After step e) the USIM shall contain the following values:
EFEPSLOCI (EPS Information)
Logically: GUTI: 24408300010266436587
Last visited registered TAI: 244/083/0001
EPS update status: updated
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
|
Hex |
0B |
F6 |
42 |
34 |
80 |
00 |
01 |
02 |
66 |
43 |
65 |
|
B12 |
B13 |
B14 |
B15 |
B16 |
B17 |
B18 |
|||||
|
87 |
42 |
34 |
80 |
00 |
01 |
00 |